DNV SERVICE DOCUMENTS

SUMMARY OF CHANGES AND

CURRENT DOCUMENT STATUS

OCTOBER 2010

DET NORSKE VERITAS

FOREWORD
DET NORSKE VERITAS (DNV) is an autonomous and independent foundation with the objectives of safeguarding life,
property and the environment, at sea and onshore. DNV undertakes classification, certification, and other verification and
consultancy services relating to quality of ships, offshore units and installations, and onshore industries worldwide, and carries
out research in relation to these functions.
DNV service documents consist of amongst other the following types of documents:
— Service Specifications. Procedual requirements.
— Standards. Technical requirements.
— Recommended Practices. Guidance.
The Standards and Recommended Practices are offered within the following areas:
A) Qualification, Quality and Safety Methodology
B) Materials Technology
C) Structures
D) Systems
E) Special Facilities
F) Pipelines and Risers
G) Asset Operation
H) Marine Operations
J) Cleaner Energy
O) Subsea Systems

The electronic pdf version of this document found through http://www.dnv.com is the officially binding version
© Det Norske Veritas

Any comments may be sent by e-mail to [email protected]

For subscription orders or information about subscription terms, please use [email protected]
Computer Typesetting (Adobe Frame Maker) by Det Norske Veritas

If any person suffers loss or damage which is proved to have been caused by any negligent act or omission of Det Norske Veritas, then Det Norske Veritas shall pay compensation to such person
for his proved direct loss or damage. However, the compensation shall not exceed an amount equal to ten times the fee charged for the service in question, provided that the maximum compen-
sation shall never exceed USD 2 million.
In this provision "Det Norske Veritas" shall mean the Foundation Det Norske Veritas as well as all its subsidiaries, directors, officers, employees, agents and any other acting on behalf of Det
Norske Veritas.
 Summary of Changes and Current Document Status, October 2010
Contents – Page 3

CONTENTS

Sec. 1 General ................................................................................................................................................ 4

Sec. 2 Current Service Specifications, Standards and Recommended Practices .................................... 6
Sec. 3 Summary of Changes ......................................................................................................................... 9
A. Changes to DNV Service Specifications ........................................................................................................................ 9
B. Changes to DNV Standards .......................................................................................................................................... 10
C. Changes to Recommended Practices ............................................................................................................................ 14

DET NORSKE VERITAS

 Summary of Changes and Current Document Status, October 2010
Sec.1 – Page 4

SECTION 1
GENERAL

Electronic binding versions

As of October 2010, we are introducing two new DNV service document types to be used for services that are
not limited to offshore and/or not to be considered as DNV Rules for classification of Ships or HSLC/NSC. The
documents have been named; DNV Service Specifications (DSS) and DNV Standards (DS).
Additionally, as of October 2010 all DNV service documents are primarily published electronically. The elec-
tronic pdf versions of the documents found through http://www.dnv.com are the officially binding versions.
In order to initiate and ensure a practical transition from the OSS/OS to DSS/DS scheme for relevant documents
and “print” scheme to the “electronic” scheme the following has been done:,
All documents that should be transferred without further change in content to the new document types DSS or
DS and those having incorporated amendments and corrections more recent than the date of the latest printed
issue, have been renamed as relevant and given the date October 2010.
Except the already incorporated amendments and corrections, no other changes have been made to the documents.
The applicable documents are shown in the table below.
List of documents given the date October 2010 due to new service document types available and “electronic” transition
Service Specifications
DNV-OSS-302 Offshore Riser Systems
DNV-OSS-305 Rules for Certification and Verification of Diving Systems
DNV-OSS-308 Verification of Lifting Appliances for the Oil and Gas Industry
DNV-OSS-309 Verification, Certification and Classification of Gas Export and Receiving Terminals
DNV-OSS-401 Technology Qualification Management
DNV-DSS-314 Verification of Hydrocarbon Refining and Petrochemical Facilities
DNV-DSS-315 Verification of Onshore LNG and Gas Facilities
Standards
DNV-OS-C501 Composite Components
DNV-OS-C502 Offshore Concrete Structures
DNV-OS-C503 Concrete LNG Terminal Structures and Containment Systems
DNV-OS-E402 Offshore Standard for Diving Systems
DNV-OS-F101 Submarine Pipeline Systems
DNV-OS-F201 Dynamic Risers
DNV-OS-J101 Design of Offshore Wind Turbine Structures
DNV-DS-J102 Design and Manufacture of Wind Turbine Blades, Offshore and Onshore Wind Turbines
Recommended Practices
DNV-RP-B401 Cathodic Protection Design
DNV-RP-C103 Column Stabilised Units
DNV-RP-C201 Buckling Strength of Plated Structures
DNV-RP-C202 Buckling Strength of Shells
DNV-RP-C204 Design against Accidental Loads
DNV-RP-C205 Environmental Conditions and Environmental Loads
DNV-RP-C206 Fatigue Methodology of Offshore Ships
DNV-RP-C207 Statistical Representation of Soil Data
DNV-RP-E402 Naval Rescue Submersibles
DNV-RP-E403 Hyperbaric Evacuation Systems
DNV-RP-F101 Corroded Pipelines
DNV-RP-F102 Pipeline Field Joint Coating and Field Repair of Linepipe Coating
DNV-RP-F103 Cathodic Protection of Submarine Pipelines by Galvanic Anodes
DNV-RP-F106 Factory Applied External Pipeline Coatings for Corrosion Control
DNV-RP-F107 Risk Assessment of Pipeline Protection
DNV-RP-F109 On-Bottom Stability Design of Submarine Pipelines
DNV-RP-F111 Interference Between Trawl Gear and Pipelines
DNV-RP-F202 Composite Risers
DNV-RP-F204 Riser Fatigue
DNV-RP-F205 Global Performance Analysis of Deepwater Floating Structures
DNV-RP-G101 Risk Based Inspection of Offshore Topsides Static Mechanical Equipment

DET NORSKE VERITAS

Summary of Changes and Current Document Status, October 2010
Page 5 – Sec.1

Update Scheme
The update scheme of the documents is as follows:
1) Whenever revised, or undergoing significant editorial changes, a document will be given a new edition date
and the main changes will be described on Page 3 of that document. The corresponding Adobe PDF file
will be made available through http://www.dnv.com/resources/rules_standards/ and the date of the “Cur-
rent edition” column of Table 1 in Sec.2 will be updated.
2) If, at a later date, the need arises for insignificant editorial corrections to the document, the electronic file
will be updated, but the edition date will be retained. However, a new Adobe PDF file will be generated
and made available through http://www.dnv.com/resources/rules_standards/. The date of the PDF file will
appear in the “Editorial corrections” column of Table 1 in Sec.2.
Discontinued updating of the “Amendments and Corrections” document
As a result of moving away from the “Print” scheme there is no longer need for a separate “Amendments and
corrections” document which intention was to supply buyers of printed documents with a detailed view of
“amendments” to the documents applicable after issued in print.
The electronic PDF files are now the officially binding versions and will always be kept current and download-
able.
Readers of documents are encouraged to regularly check for updates in order to ensure that they hold the cur-
rent updated versions.

DET NORSKE VERITAS

 Summary of Changes and Current Document Status, October 2010
Sec.2 – Page 6

SECTION 2
CURRENT SERVICE SPECIFICATIONS, STANDARDS AND
RECOMMENDED PRACTICES

Table 1 Current Documents

Current Editorial
edition corrections
Service Specifications
DNV-OSS-101 Rules for Classification of Offshore Drilling and Support Units October 2010 –
DNV-OSS-102 Rules for Classification of Floating Production, Storage and October 2010 –
Loading Units
DNV-OSS-103 Rules for Classification of LNG/LPG Floating Production and Storage Units or October 2008 October 2009
Installations
DNV-OSS-121 Classification based on Performance Criteria Determined from Risk Assess- October 2008 –
ment Methodology
DNV-OSS-201 Verification for Compliance with Norwegian Shelf Legislation April 2010 –
DNV-OSS-202 Verification for Compliance with UK Shelf Regulations October 2008 –
DNV-OSS-300 Risk Based Verification April 2004 –
DNV-OSS-301 Certification and Verification of Pipelines October 2000 –
DNV-OSS-302 Offshore Riser Systems October 2010 –
DNV-OSS-304 Risk Based Verification of Offshore Structures October 2006 –
DNV-OSS-305 Rules for Certification and Verification of Diving Systems October 2010 –
DNV-OSS-306 Verification of Subsea Facilities June 2004 –
DNV-OSS-307 Verification of Process Facilities June 2004 –
DNV-OSS-308 Verification of Lifting Appliances for the Oil and Gas Industry October 2010 –
DNV-OSS-309 Verification, Certification and Classification of Gas Export and October 2010 –
Receiving Terminals
DNV-OSS-312 Certification of Tidal and Wave Energy Converters October 2008 –
DNV-OSS-313 Pipe Mill and Coating Yard - Qualification April 2009 –
DNV-DSS-314 Verification of Hydrocarbon Refining and Petrochemical Facilities October 2010 –
DNV-DSS-315 Verification of Onshore LNG and Gas Facilities October 2010 –
DNV-OSS-401 Technology Qualification Management October 2010 –
Standards
DNV-OS-A101 Safety Principles and Arrangement October 2010 –
DNV-OS-B101 Metallic Materials April 2009 –
DNV-OS-C101 Design of Offshore Steel Structures, General (LRFD method) October 2008 April 2010
DNV-OS-C102 Structural Design of Offshore Ships October 2008 October 2009
DNV-OS-C103 Structural Design of Column Stabilised Units (LRFD method) October 2008 October 2009
DNV-OS-C104 Structural Design of Self-elevating Units (LRFD method) October 2008 April 2009
DNV-OS-C105 Structural Design of TLPs (LRFD method) October 2008 October 2009
DNV-OS-C106 Structural Design of Deep Draught Floating Units/Spars (LRFD and WSD October 2008 October 2009
Method)
DNV-OS-C107 Structural Design of Ship-shaped Drilling and Well Service Units October 2008 October 2009
DNV-OS-C201 Structural Design of Offshore Units (WSD method) October 2008 October 2009
DNV-OS-C301 Stability and Watertight Integrity October 2010 –
DNV-OS-C401 Fabrication and Testing of Offshore Structures October 2010 –
DNV-OS-C501 Composite Components October 2010 –
DNV-OS-C502 Offshore Concrete Structures October 2010 –
DNV-OS-C503 Concrete LNG Terminal Structures and Containment Systems October 2010 –
DNV-OS-D101 Marine and Machinery Systems and Equipment October 2010 –
DNV-OS-D201 Electrical Installations October 2008 October 2009
DNV-OS-D202 Automation, Safety, and Telecommunication Systems October 2008 –
DNV-OS-D203 Integrated Software-Dependent System (Tentative Standard) April 2010 –
DNV-OS-D301 Fire Protection October 2008 October 2009
DNV-OS-E101 Drilling Plant October 2009 –
DNV-OS-E201 Oil and Gas Processing Systems October 2010 –
DNV-OS-E301 Position Mooring October 2010 –
DNV-OS-E302 Offshore Mooring Chain October 2008 October 2009
DNV-OS-E303 Offshore Mooring Fibre Ropes October 2010 –
DNV-OS-E304 Offshore Mooring Steel Wire Ropes April 2009 October 2009

DET NORSKE VERITAS

Summary of Changes and Current Document Status, October 2010
Page 7 – Sec.2

Table 1 Current Documents (Continued)

Current Editorial
edition corrections
DNV-OS-E401 Helicopter Decks October 2008 October 2009
DNV-OS-E402 Offshore Standard for Diving Systems October 2010 –
DNV-OS-E403 Offshore Loading Buoys October 2008 –
DNV-OS-E406 Design of Free Fall Lifeboats April 2010 –
DNV-OS-F101 Submarine Pipeline Systems October 2010 –
DNV-OS-F201 Dynamic Risers October 2010 –
DNV-OS-J101 Design of Offshore Wind Turbine Structures October 2010 –
DNV-DS-J102 Design and Manufacture of Wind Turbine Blades, Offshore and October 2010 –
Onshore Wind Turbines
DNV-OS-J201 Offshore Substations for Wind Farms October 2009 –
DNV-OS-J301 Standard for Classification of Wind Turbine Installation Units October 2010 –
Recommended Practices
DNV-RP-A201 Plan Approval Documentation Types – Definitions October 2010 –
DNV-RP-A203 Qualification Procedures for New Technology September 2001 –
DNV-RP-B101 Corrosion Protection of Floating Production and Storage Units April 2007 –
DNV-RP-B401 Cathodic Protection Design October 2010 –
DNV-RP-C101 Allowable Thickness Diminution for Hull Structure of Offshore Ships April 2007 –
DNV-RP-C102 Structural Design of Offshore Ships February 2002 –
DNV-RP-C103 Column Stabilised Units October 2010 –
DNV-RP-C201 Buckling Strength of Plated Structures October 2010 –
DNV-RP-C202 Buckling Strength of Shells October 2010 –
DNV-RP-C203 Fatigue Design of Offshore Steel Structures April 2010 –
DNV-RP-C204 Design against Accidental Loads October 2010 –
DNV-RP-C205 Environmental Conditions and Environmental Loads October 2010 –
DNV-RP-C206 Fatigue Methodology of Offshore Ships October 2010 –
DNV-RP-C207 Statistical Representation of Soil Data October 2010 –
DNV-RP-D101 Structural Analysis of Piping Systems October 2008 –
DNV-RP-D201 Integrated Software Dependent Systems October 2009 –
DNV-RP-E101 Recertification of Well Control Equipment October 2008 –
DNV-RP-E102 Recertification of Blowout Preventers and Well Control Equipment for the US June 2010 –
Outer Continental Shelf
DNV-RP-E301 Design and Installation of Fluke Anchors in Clay 2000 –
DNV-RP-E302 Design And Installation of Plate Anchors in Clay December 2002 –
DNV-RP-E303 Geotechnical Design and Installation of Suction Anchors in Clay October 2005 –
DNV-RP-E304 Damage Assessment of Fibre Ropes for Offshore Mooring April 2005 –
DNV-RP-E401 Survey of Diving Systems April 2007 –
DNV-RP-E402 Naval Rescue Submersibles October 2010 –
DNV-RP-E403 Hyperbaric Evacuation Systems October 2010 –
DNV-RP-F101 Corroded Pipelines October 2010 –
DNV-RP-F102 Pipeline Field Joint Coating and Field Repair of Linepipe Coating October 2010 –
DNV-RP-F103 Cathodic Protection of Submarine Pipelines by Galvanic Anodes October 2010 –
DNV-RP-F105 Free Spanning Pipelines February 2006 –
DNV-RP-F106 Factory Applied External Pipeline Coatings for Corrosion Control October 2010 –
DNV-RP-F107 Risk Assessment of Pipeline Protection October 2010 –
DNV-RP-F108 Fracture Control for Pipeline Installation Methods Introducing January 2006 –
Cyclic Plastic Strain
DNV-RP-F109 On-Bottom Stability Design of Submarine Pipelines October 2010 –
DNV-RP-F110 Global Buckling of Submarine Pipelines October 2007 –
Structural Design due to High Temperature/High Pressure
DNV-RP-F111 Interference Between Trawl Gear and Pipelines October 2010 –
DNV-RP-F112 Design of Duplex Stainless Steel Subsea Equipment Exposed to October 2008 –
Cathodic Protection
DNV-RP-F113 Pipeline Subsea Repair October 2007 –
DNV-RP-F116 Integrity Management of Submarine Pipeline Systems October 2009 –
DNV-RP-F118 Pipe Girth Weld Aut System Qualification and Project Specific Procedure October 2010 –
Validation
DNV-RP-F201 Design of Titanium Risers October 2002 –
DNV-RP-F202 Composite Risers October 2010 –
DNV-RP-F203 Riser Interference April 2009 –

DET NORSKE VERITAS

 Summary of Changes and Current Document Status, October 2010
Sec.2 – Page 8

Table 1 Current Documents (Continued)

Current Editorial
edition corrections
DNV-RP-F204 Riser Fatigue October 2010 –
DNV-RP-F205 Global Performance Analysis of Deepwater Floating Structures October 2010 –
DNV-RP-F206 Riser Integrity Management April 2008 –
DNV-RP-F301 Subsea Separator Structural Design April 2007 –
DNV-RP-F302 Selection and Use of Subsea Leak Detection Systems April 2010 –
DNV-RP-G101 Risk Based Inspection of Offshore Topsides Static Mechanical Equipment October 2010 –
DNV-RP-G103 Non-intrusive Inspection October 2007 –
DNV-RP-H101 Risk Management in Marine and Subsea Operations January 2003 –
DNV-RP-H102 Marine operations during Removal of Offshore Installations April 2004 –
DNV-RP-H103 Modelling and Analysis of Marine Operations April 2010 –
DNV-RP-J201 Qualification Procedures for CO2 Capture Technology April 2010 –
DNV-RP-J202 Design and Operation of CO2 Pipelines April 2010 –
DNV-RP-O401 Safety and Reliability of Subsea Systems April 1985 –
DNV-RP-O501 Erosive Wear in Piping Systems 2005 2007

DET NORSKE VERITAS

Summary of Changes and Current Document Status, October 2010
Page 9 – Sec.3

SECTION 3
SUMMARY OF CHANGES

A. Changes to DNV Service Specifications

DNV Service Specifications – Main changes
Document number Document title Main changes
DNV-OSS-101 Rules for Classification — Well Intervention Units:
of Offshore Drilling The current DNV-OSS-101 does not take into account the needs of the indus-
try. Well Intervention Unit service notation has therefore been split in two,
and Support Units and one of the service notations will be voluntary instead of mandatory as it is
today.
The WELL notation has been split in two - where the WELL-1 notation will
not require the owner to certify the sub sea equipment (RS1).
— ISDS:
New voluntary class notations for Independent Software Dependent System
Integration (ISDS-1 to 3) introduced.
— Hull PMS:
Hull PMS (planned maintenance system) introduced as an optional alternative
survey arrangement- also for offshore units.
— In-service Inspection of structures:
The inspection scope for column-stabilised units has been updated with in-
creased emphasis on renewal survey, and corresponding reduced external
scope for intermediate surveys.
— Provisions for Ageing Units:
Alternative to increased inspection due to age has been introduced, allowing
for inspection based on the actual condition rather than age in order to main-
tain the required safety level.
DNV-OSS-102 Rules for Classification — ISDS:
of Floating Production, New voluntary class notations for Independent Software Dependent System
Integration (ISDS -1 to 3) have been introduced.
Storage and Loading Units
— Hull PMS:
Hull PMS (Planned Maintenance System) has been introduced as an optional
alternative survey arrangement also for offshore units.
— In-service Inspection of structures:
— The inspection scope for column-stabilised units has been updated with
increased emphasis on renewal survey, and corresponding reduced exter-
nal scope for intermediate surveys.
— Revised scope for boiler survey: Aligned with new IACS unified require-
ments
— Revised description of Machinery PMS: Aligned with latest text from
Ship Rules Pt.7 Ch.1
— Revised description of PMS RCM scheme (reliability-centred mainte-
nance)
— New alternative survey arrangement Offshore CM: Introduction of Off-
shore CM as a survey arrangement based on use of an approved service
provider for execution of condition monitoring.
— General update of references and editorial improvements: Based on expe-
rience feed-back from users.
DNV-DSS-314 Verification of Hydrocar- This service specification; DSS-314: “Verification of Hydrocarbon Refining and
bon Refining and Petro- Petrochemical Facilities” replaces the previous version of the document with short
chemical Facilities name; DNV-OSS-314. There are no changes in content, only how the document is
referred to, as OSS now will be used for Service Specifications intended for Off-
shore use.
DNV-DSS-315 Verification of Onshore This service specification; DSS-315: “Verification of Onshore LNG and Gas Facil-
LNG and Gas Facilities ities” replaces the previous version of the document with short name; DNV-OSS-
315. There are no changes in content, only how the document is referred to, as OSS
now will be used for Service Specifications intended for Offshore use.

DET NORSKE VERITAS

 Summary of Changes and Current Document Status, October 2010
Sec.3 – Page 10

B. Changes to DNV Standards

DNV Standards – Main changes
Document number Document title Main changes
DNV-OS-A101 Safety Principles and — Item F301 in Sec.6 “Escape and communication” has been amended.
Arrangement
DNV-OS-C301 Stability and Watertight General
Integrity
— Several minor updates of items that was out of date/incorrect has been carried
out in order to make the OS more user-friendly.
Ch.2 Sec.1 Stability
— In Sub-section element E300, additional damage stability criterion for Self-El-
evating units have been included in order to align the OS with the 2009 IMO
MODU Code.
DNV-OS-D101 Marine and Machinery General
Systems and Equipment
— In addition to the below stated changes, a number of corrections and clarifica-
tions have been made in the existing text.
Ch.1 Sec.1
— A. General:
— Included reference to Ballast Water Treatment Units in Ship Rules Pt.4
Ch.6.
— B. Normative References:
— Table B2 Normative references revised to be in line with systems listed
in Ch.2 Sec.4.
— D. Definitions:
— Definition of Redundancy type revised to be in line with DNV-OS-D202.
Ch.2 Sec.1
— A. Arrangement:
— Arrangement of hydraulic power units and purifiers for heated fuel oil re-
vised to be in line with Rules for classification of ships Pt.4 Ch.1
— Requirements to plastic pipes revised to be in line with Rules for classifi-
cation of ships Pt.4 Ch.6
— Requirement for remotely controlled valves, valves on side and bottom of
floating units and installations, and fittings on collision bulkhead revised to
be in line with Rules for classification of ships Pt.4 Ch.6
— Included requirements for Refrigerant Systems, in line with Ship Rules.
Added reference to DNV-OS-D202.
— B. Construction and Function:
— Table B1 Environmental condition for unit or installation of ship-shaped
type revised to be in line with Rules for classification of ships Pt.4 Ch.1
— Guidance note regarding Main functions deleted as it is already defined
in DNV-OSS-101
— Added assumption regarding availability of engines combined as emer-
gency generators/generators for electrical propulsion/dynamic propul-
sion.
— C. Personnel Protection:
— Item C102 has been deleted.
Ch.2 Sec.2
— A. General:
— Updated Table A1, Classes of Piping systems in line with Rules for clas-
sification of ships Pt.4 Ch.6.
— B. Materials:
— Use of grey cast iron revised to be in line with Rules for classification of
ships Pt.4 Ch.6
— Requirements to plastic pipes revised to be in line with Rules for classifi-
cation of ships Pt.4 Ch.6.

DET NORSKE VERITAS

Summary of Changes and Current Document Status, October 2010
Page 11 – Sec.3

DNV Standards – Main changes (Continued)

Document number Document title Main changes
— C. Design Conditions:
— Table C5 giving permissible stresses with reference to DNV specific steel
qualities has been deleted and new reference made to recognized standards
in DNV-OS-B101, in line with Rules for classification of ships Pt.4 Ch.6
— Requirements for Thermal expansion stresses, Documentation of thermal
stress calculation, Stress calculation and Table C6 included in line with
Rules for classification of ships Pt.4 Ch.6
— Requirements to plastic pipes revised to be in line with Rules for classifi-
cation of ships Pt.4 Ch.6.
— E. Valves:
— Requirement to valve design revised in line with Rules for classification
of ships
— Deleted requirement regarding screw-on valve bonnets.
— F. Flexible Hoses:
— The requirements for flexible hoses have been revised in line with Rules
for classification of ships and IACS UR P2 2.12.
— G. Detachable Pipe Connections:
— The requirements for detachable pipe connections have been revised in
line with Rules for classification of ships and IACS UR P2 2.12. Inserted
Table G2 and G3.
— H. Socket Welded Joints and Slip-on Sleeve Welded Joints:
— Use of slip-on sleeve welded joints in overboard pipes restricted in line
with Rules for classification of ships Pt.4 Ch.6.
Ch.2 Sec.3
— B. Ballast, Bilge and Drainage Systems General:
— Deleted general capacity requirement.
— F. Air, Overflow and Sounding Pipes:
— Vent for lub. oil tanks revised in line with Rules for classification of ships
Pt.4 Ch.6
— Requirement to overflow pipes and short sounding pipes revised in line
with Rules for classification of ships Pt.4 Ch.6.
Ch.2 Sec.4
— A. General:
— Added new sub-section element A100 “Scope”.
— B. Cooling System:
— Included requirements for combined cooling water/fuel oil heating sys-
tems, and sea chest arrangement for class notations for navigation in ice,
in line with Rules for classification of ships Pt.4 Ch.6.
— D. Fuel Oil System:
— Included acceptance criteria for use of oil fuels with a flash point less than
60°C, in line with Rules for classification of ships Pt.4 Ch.6
— Valve arrangement on fuel oil tanks revised in line with Rules for classi-
fication of ships Pt.4 Ch.6 and SOLAS Ch.II-2
— Requirements to remote stop of fuel oil pumps and fans deleted since they
are already stated in DNV-OS-D201.
— G. Steam Systems:
— Included requirements to blow down valves on unit's side in line with
Rules for classification of ships Pt.4 Ch.6.
— H. Hydraulic Systems:
— Requirements to hydraulic cylinders are deleted and reference made to
DNV Standards for Certification No. 2.9 (Approval Program No.5-
778.93).
— I. Pneumatic Power Supply:
— Revised in line with Rules for classification of ships Pt.4 Ch.6.

DET NORSKE VERITAS

 Summary of Changes and Current Document Status, October 2010
Sec.3 – Page 12

DNV Standards – Main changes (Continued)

Document number Document title Main changes
— J. Pneumatic Starting Arrangements:
— Revised in line with Rules for classification of ships Pt.4 Ch.6 and expe-
rience feedback. Included requirement to fire pump drivers.
— K. Heating, Ventilation and Air Conditioning (HVAC):
— Added requirement for installation of electrical fan motors installed in
ventilation ducts for hazardous spaces, in line with Rules for classifica-
tion of ships Pt.5 Ch.3
— Safety requirements for Refrigeration plants revised to be applicable for
plants with total prime mover effect of 100W and above, in line with
Rules for classification of ships Pt.4 Ch.1.
— L. Use of Gas and Crude Oil for Auxiliary Boilers and Turbines:
— Reference to DNV-OS-E201 also applicable for gas fuelled boilers.
Ch.2 Sec.5
— B. Recognised Codes and Standards:
— Deleted reference to recognized codes and standards.
— C. General Marine Equipment:
— Clarified that for certification of machinery and equipment with similar
application as for ships, requirements as given in the Rules for Classifica-
tion of Ships will be applicable. Recognised international standards may
be used on a case by case basis.
Ch.3 Sec.1
— C. Certification of Materials and Components:
— Included certification requirements for hydraulic cylinders in Table C2
— Table C5 updated in line with Rules for classification of ships Pt.4 Ch.6
— Requirement to certification of compressors revised to be in line with
Ship Rules.
— E. Survey During Installation and Commissioning:
— Deleted requirement that commissioning procedures shall be approved.
Further, added some text clarifying DNV’s involvement with commis-
sioning.
DNV-OS-E201 Oil and Gas Processing — Offloading systems:
Systems
— Requirements for offloading systems updated and expanded. Moved to a
new separate Ch.2 Sec.12, stipulating requirements to design of arrange-
ment, safety & control systems, hoses and hawsers of offloading systems.
— Introducing a new voluntary class notation “OFFLOADING”, granted to
units complying with Ch.2 Sec.12 of the revised DNV-OS-E201.
— Requirements for equipment certification - relevant for the
OFFLOADING notation introduced in Ch.3.
— Ch.2 Sec.9 Materials and Corrosion Protection completely re-written for im-
proved alignment with recognised industry codes and practice.
— General updating of references and editorial improvements based on experi-
ence feed-back from users.
DNV-OS-E301 Position Mooring Ch.2 Sec.1
— B306: Included a definition of extreme value for mooring line tensions during
a squall event.
— B700: Adjusted the required drag coefficients for steel wire ropes.
Ch.2 Sec.2
— B101: Added fibre rope degradation method.
— B110 (previous item B106): updated guidance regarding e-modules of studless
chain based on information from VICINAY.
— E201: Updated Table E1 with respect to in-service assessment.
— F800: Requirements to investigate the possibility of VIM on steel wire and fi-
bre ropes included. If VIM is a possible load effect, the effect shall be included
in fatigue assessment.

DET NORSKE VERITAS

Summary of Changes and Current Document Status, October 2010
Page 13 – Sec.3

DNV Standards – Main changes (Continued)

Document number Document title Main changes
Ch.2 Sec.4
— Sub-section J, Added 103 and 200: design criteria for fibre ropes and yarn for
fibre ropes.
— Q105: Added requirement to measuring ranges for tension measuring equip-
ment.
— R403: Added design requirement to element between MLBE and mooring
line.
Ch.2 Sec.5
— A100: Added requirements for anchor shackles for mobile mooring that are
not of R-quality.
Ch.3 Sec.1
— B100: Added that temporary mooring is not a class requirement for DP units
with DYNPOS-AUTR or AUTRO notations. Towing arrangements for ship
shaped units shall be according to DNV Rules for Classification of Ships.
— D602: It is emphasized that it is the technical part of the standard that could be
replaced by e.g. API RP2SK and ISO 19901-7, and that equipment and mate-
rial shall be certified by DNV.
Ch.3 Sec.2
— A200: Chain qualities R4S and R5 are included in the standard.
— G200: Requirements added regarding in-service condition assessment for fi-
bre ropes.
DNV-OS-E303 Offshore Mooring Fibre — Definitions of terms have been updated.
Ropes — This standard now presents three certificate formats, ropes for Long-Term -,
ropes for Mobile Moorings and one for thimbles.
— Approval of Manufacturer schemes for fibre rope manufacturers and load
bearing yarn manufacturers are introduced.
— Testing procedure for load bearing yarns is introduced
— The structure of each chapter is reorganized in order to separate the applicable
requirements to long term mooring and. mobile mooring. The scope of testing
for mobile mooring is brought in line with ISO 18962, whilst for long term
moorings the principle of application of specific mooring systems perform-
ance is reinforced.
— Rules for hardware (thimbles) have been clarified.
— Testing methods, which are subject to approval, have been removed from Ch.2
Sec.3.
— The previous Appendixes A, B, C and D on ‘Fibre rope stretch and stiffness’,
‘Measuring and Expressing the Rope Change-in-Length Properties’, ‘Change-
in-length test methods for long-term mooring’ and ‘Quality review report’
have been removed.
— The term ‘soil barrier’ is replaced by ‘filter’, as this is the commonly used term
in other standards.
— Added a new Appendix A containing ‘scope of survey’ for fibre-rope production.
DNV-DS-J102 Design and Manufacture of This service specification; DS-J102: “Design and Manufacture of Wind Turbine
Wind Turbine Blades, Off- Blades, Offshore and Onshore Wind Turbines” replaces the previous version of the
shore and Onshore Wind document with short name; DNV-OS-J102. There are no changes in content, only
Turbines how the document is referred to, as OS now will be used for Standards intended for
Offshore use.
DNV-OS-J301 Standard for Classification This new DNV Offshore Standard provides special technical requirements for units
of Wind Turbine which are purpose built for installation/maintenance of Offshore Wind Turbine.
The standard supports the special service notation “Wind Turbine Installation
Installation Units Unit” which was introduced through the DNV-OSS-101 in October 2009.

DET NORSKE VERITAS

 Summary of Changes and Current Document Status, October 2010
Sec.3 – Page 14

C. Changes to Recommended Practices

DNV Recommended Practices – Main changes
Document number Document title Main changes
DNV-RP-A201 Plan Approval Documenta- Sec.2 Documentation Types
tion Types – Definitions
— B200: Document type definition of Freeboard Plan is updated.
— H190: Container stowage and securing manual is amended.
— New item I260 – Control and monitoring systems - periodical test procedure
— New documentation types have been added as follows:
— M085 – Hazardous materials documentation - appendix 2 substances
— M100 – Material declaration
— M110 – Declaration of conformity relating to use of hazardous materials
— M120 – Hazardous materials location plan.
In addition documentation types M081, M083 and M084 have been amended.
DNV-RP-F118 Pipe Girth Weld Aut Sys- This new document provides a uniform guideline for the general qualification of
tem Qualification and Automated Ultrasonic Testing (AUT) systems, ensuring that the qualification and
Project Specific Procedure project specific validation of any AUT system is according to the requirements of
Validation OS-F101 Appendix E and is consistently performed to comply with the specific re-
quirements of the referenced code.
In principle, the guideline can be utilised for all materials but special care shall be
taken for applications where inconsistent wave propagation or other wave physics
are affected by structural properties.

DET NORSKE VERITAS