Green University of Bangladesh

Department of Electrical and Electronics Engineering (EEE)

Semester: (Fall, Year: 2024), B.Sc. in EEE (Day)

Report on
Traffic Light Controller
Design

Course Title: Electronics Lab

Course Code: EEE-304

Students Details
Name ID
Towhid Islam 231001004
Md. Rakib 231901019
Abu Saleh Nasim 231901003

Submission Date: 12/07/2024

Course Teacher’s Name:

Mr. M M Naushad Ali

Lab Project Status

Marks Signatur
: e:
Comment Date
s: :
Contents
1 Introduction
1.1 ...........................................................................................................................

2 Design/Development/Implementation of the Project

2.1 Introduction.......................................................................................................
2.2 Project Details...................................................................................................
2.2.1 Subsection_name..................................................................................
2.3 Implementation..................................................................................................
2.3.1 Subsection_name..................................................................................
2.4 Algorithms.........................................................................................................

3 Performance Evaluation
3.1 Simulation Envirnment/ Simulation Procedure................................................8
3.1.1 Subsectin.............................................................................................8
3.1.2 Subsection...........................................................................................8
3.2 Results Analysis/Testing..................................................................................8
3.2.1 Result_portion_1.................................................................................8
3.2.2 Result_portion_2.................................................................................8
3.2.3 Result_portion_3.................................................................................8
3.3 Results Overall Discussion..............................................................................9
3.3.1 Complex Engineering Problem Discussion......................................9

4 Conclusion 10
4.1 Discussion......................................................................................................10
4.2 Limitations.....................................................................................................10
4.3 Scope of Future Work...................................................................................10
Chapter 1

Introduction
This report details the design and implementation of a traffic light
controller for an intersection with a main highway and a secondary
access road. The controller aims to optimize traffic flow by
prioritizing vehicles on lane B while ensuring smooth traffic
movement on all lanes.
 Table 1.1: Summary of the attributes touched by the mentioned projects
Name of the P Explain how to
Attributess address
P1: Depth of knowledge required —-
P2: Range of conflicting require- —-
ments
P3: Depth of analysis required —-
P4: Familiarity of issues —-
P5: Extent of applicable codes —-
P6: Extent of stakeholder involve- —-
ment and conflicting requirements
P7: Interdependence —-

1.1 Application
Write about the exact application of your chosen project in the real world in details.
In every section please add subsections and figures and citations as references [1] also.
Chapter 2

Design/Development/
Implementation of the Project

2.1 Introduction
Start the section with a general discussion of the project [2] [3] [4].

2.2 Project Details

In this section, you will elaborate on all the details of your project, using subsections if
necessary.

2.2.1 Subsection_name

Figure 2.1: Figure name

 You can fix the height, width, position, etc., of the figure accordingly.

2.3 Implementation
All the implementation details of your project should be included in this section, along
with many subsections.

2.3.1 Subsection_name
This is just a sample subsection. Subsections should be written in detail. Subsections
may include the following, in addition to others from your own project.

The workflow

Tools and

libraries

Implementation details (with screenshots and programming codes)

Each subsection may also include subsubsections.

2.4 Algorithms
The algorithms and the programming codes in detail should be included .
Pseudo-codes are also encouraged very much to be included in this chapter for your
project.

• Bullet points can also be included anywhere in this project report.

Algorithm 1: Sample Algorithm
Input: Your Input
Output: Your
output Data:
Testing set x
∞
1 ∑i=1 := 0 // this is a comment
/* Now this is an if...else conditional loop */
2 if Condition 1 then
3 Do something // this is another comment
4 if sub-Condition then
5 Do a lot
6 else if Condition 2 then
7 Do Otherwise
/* Now this is a for loop */
8 for sequence do
9 loop instructions

10 else
11 Do the rest
/* Now this is a While loop */
12 while Condition do
13 Do something
Chapter 3

Performance Evaluation

3.1 Simulation Environment/ Simulation Procedure

Discuss the experimental setup and environment installation needed for the simulation
of your outcomes.

3.1.1 Subsection

3.1.2 Subsection

3.2 Results Analysis/Testing

Discussion about your various results should be included in this chapter in detail.

3.2.1 Result_portion_1
The results of any specific part of your project can be included using subsections.

3.2.2 Result_portion_2
Each result must include screenshots from your project. In addition to screenshots,
graphs should be added accordingly to your project.

3.2.3 Result_portion_3
Each result must have a single paragraph describing your result screenshots or graphs
or others. This is a simple discussion of that particular portion/part of your result.
 Figure 3.1: A graphical result of your project

3.3 Results Overall Discussion

A general discussion about how your result has arrived should be included in this
chap- ter. Where the problems detected from your results should be included as well.

3.3.1 Complex Engineering Problem Discussion

[OPTIONAL] In this subsection, if you want, you can discuss in details the attributes
that have been touched by your project problem in details. This has already been men-
tioned in the Table 1.1.
Chapter 4

Conclusion

4.1 Discussion
Discuss the contents of this chapter and summarized the description of the work and the
results and observation. Generally, it should be in one paragraph.

4.2 Limitations
Discuss the limitations of the project. Limitations must be discussed, with the help of
some critical analysis.

4.3 Scope of Future Work

Discuss the future work of the project, that is your plans for more work and extension
of your project.
References

[1] Omid C Farokhzad and Robert Langer. Impact of nanotechnology on drug delivery.
ACS nano, 3(1):16–20, 2009.

[2] Uthayasankar Sivarajah, Muhammad Mustafa Kamal, Zahir Irani, and Vishanth
Weerakkody. Critical analysis of big data challenges and analytical methods.
Jour- nal of Business Research, 70:263–286, 2017.

[3] Douglas Laney. 3d data management: controlling data volume, velocity and
variety. gartner, 2001.
[4] MS Windows NT kernel description. http://web.archive.org/web/
20080207010024/http://www.808multimedia.com/winnt/kernel.h
tm. Ac- cessed Date: 2010-09-30.