Technical manual for

frequency converters RD11 series

RD11 Series Frequency converter Manual

Contents
1 OVERVIEW ................................................................................................................................................ 1

1.1 SAFETY PRECAUTIONS ........................................................................................................................... 1

1.2 BEFORE USE........................................................................................................................................... 1
1.3 TECHNICAL SPECIFICATIONS.................................................................................................................... 2

2 INSTALLATION.......................................................................................................................................... 4

3 KEYBOARD LAYOUT AND OPERATING INSTRUCTIONS .............................................................. 11

4 FUNCTION PARAMETER TABLE ......................................................................................................... 13

4.1 PARAMETER ICON DESCRIPTION ............................................................................................................ 13

4.2 PARAMETER CONTENT .......................................................................................................................... 13
4.3 ENVIRONMENT APPLICATION.................................................................................................................. 14
4.4 F01：BASIC SETTINGS........................................................................................................................ 14
4.5 F02：MOTOR PARAMETER .................................................................................................................. 17
4.6 F03：VECTOR CONTROLLING ............................................................................................................. 19
4.7 F04 ：V/F CONTROLLING................................................................................................................... 22
4.8 F05：INPUT TERMINAL ........................................................................................................................ 23
4.9 F06：OUTPUT TERMINAL .................................................................................................................... 26
4.10 F07 ：OPERATIONAL CONTROL ......................................................................................................... 30
4.11 F08：AUXILIARY CONTROL ................................................................................................................ 32
4.12 F09：RESERVED ............................................................................................................................... 33
4.13 F10：PROTECTION PARAMETER ........................................................................................................ 33
4.14 F11：OPERATOR PARAMETER............................................................................................................ 36
4.15 F12：COMMUNICATION PARAMETER .................................................................................................. 38
4.16 F13：PROCESS PID CONTROL .......................................................................................................... 40
4.17 F14:MULTI-SPEED AND SIMPLE PLC .................................................................................................... 42
4.18 C0X：MONITORING PARAMETER ........................................................................................................ 45
4.19 TERMINAL SELECTION FUNCTION ......................................................................................................... 46
4.20 FAULT AND WARNING CODE TABLE....................................................................................................... 47

5 INSPECTION, MAINTENANCE AND GUARANTEE ........................................................................... 48

5.1 INSPECTION .......................................................................................................................................... 49

II
RD11 Series Frequency converter Manual
5.2 MAINTENANCE ...................................................................................................................................... 50
5.3 PRODUCT WARRANTY .......................................................................................................................... 50

APPENDIX I: MODBUS COMMUNICATION PROTOCOL ........................................................................... 51

●COMMUNICATION FRAME STRUCTURE ............................................................................................................. 51

●COMMAND CODE AND COMMUNICATION DATA DESCRIPTION ............................................................................. 51

APPENDIX II: TERMINAL WIRING METHOD ............................................................................................... 54

III
RD11 Series Frequency converter Manual

1 Overview
1.1 Safety Precautions
To ensure safe and reasonable use of this product, please use the product after fully understanding the safety precautions described in this manual.
Warning signs and meanings
The following symbols are used in this manual to indicate that it is an important part of safety. Failure to follow these precautions may result in personal
injury or death, damage to this product and associated systems.

DANGER: Death or major safety hazard can result from incorrect operation.

Caution: Wrong operation may cause minor injuries

Operational qualification
This product must be operated by trained professionals. Moreover, the operator must be trained in professional skills, familiar with the installation,
wiring, operation and maintenance of the equipment, and properly respond to various emergencies in use.
Safety guidance
Warning signs are provided for your safety. They are measures to prevent injury to the operator and damage to the product and associated
systems. Please read this manual carefully before use and follow the safety rules and warnings in this manual strictly while operating.
●Proper transportation, storage, installation, and careful operation and maintenance are essential for the safe operation of the inverter. During
transmission and storage, ensure that the inverter is not subject to shock and vibration. It must also be stored in a dry, non-corrosive atmosphere,
non-conductive dust and ambient temperature less than 60 °C.
● This product has a dangerous voltage and it controls a potentially dangerous moving mechanism. Failure to follow these instructions or not
complying with the requirements of this manual may result in personal injury or death, damage to the product and associated systems.
● Do not perform wiring work while the power is on, otherwise there is a danger of death due to electric shock. When wiring, inspection,
maintenance, etc., please cut off the power of all related equipment and confirm that the DC voltage of the main circuit has dropped to Safety
level, wait 5 minutes before performing related work.
● The power cable, motor cable, and control cable must be tightly connected. The grounding terminal must be grounded reliably and the grounding
resistance is less than 10Ω.
● The static electricity of the human body will seriously damage the internal sensitive components. Before performing related operations, please
observe the measures and methods specified in the static electricity prevention measures (ESD), otherwise the inverter may be damaged.
●Since the output voltage of the inverter is a pulse waveform, if the output side is equipped with a capacitor with improved power factor or a
varistor for lightning protection, be sure to remove or modify it on the input side of the inverter.
● Do not add switching devices such as circuit breakers and contactors on the output side of the inverter (if the switching device must be
connected to the output side, the output current of the inverter must be zero when the switch is activated).
● No matter where the fault occurs in the control equipment, it may cause a shutdown and a major accident. Therefore, take the necessary
external protection measures or spare equipment.
● This product can only be used in accordance with the manufacturer's specified use. It may not be used in special fields such as emergency,
rescue, shipbuilding, medical, aviation, nuclear facilities, etc. without permission.
●The maintenance of this product can only be carried out by the company or by a professional authorized by the company. Unauthorized
modification and use of accessories not approved by the company may result in product failure. Any defective devices must be replaced in time
for maintenance.
● The company is not responsible for any damage or equipment damage caused by your company or your company's customers who fail to
comply with the contents of this manual
1.2 Before use
Upon receipt of the product you ordered, please check the outsourcing for damage and open the outer packaging after confirming the integrity, and
confirm that whether the inverter is damaged, scratched or dirty. (Damage caused during transportation does not belong to our company's
warranty). If the product you received is damaged, please contact the company or the shipping company immediately. After confirming that the

1
RD11 Series Frequency converter Manual
received product is intact, please confirm that the received inverter model is consistent with the product you ordered.
Inverter model description

Type code decoding

Example RD11-T4-1720-LO-IP20-BU-DC
RD11 Product Series
T4 Voltage class 380-400V / S2 220V / T6 690V / T9 1140V
1720 Rated output current, A
LO Low-overload / HO – high-overload
IP20 Environmental protection class IP20 or IP54
BU Brake unit integrated
DC DC choke integrated

Input voltage 220V 380V

Rated power(kW) Rated output current (A)
0.75 4 3
1.5 7 4
2.2 10 6.0
4 10
5.5 13
7.5 17
11 25
15 32
18.5 38
22 45
30 60
37 75
45 90
55 110
75 150
90 180
110 210
132 250
160 310
185 340
200 380
220 415
250 470
280 510
315 600
355 670
400 750
450 810
500 860
560 990
630 1100
710 1280

1.3 Technical specifications

2
RD11 Series Frequency converter Manual
Items specifications
Voltage, frequency Single phase :220V 50/60Hz;Three phase: 220V 50/60Hz; Three phase 380V 50/60Hz ,
Allowable voltage unbalance rate:<3%; Frequency:±5%; aberration rate: as IEC61800-2 required
Power fluctuations
Inrush current Lower than rated current
input
Power factor ≥0.94(with DC reactor)
Efficiency ≥96%
Output voltage Output under rated condition: 3 phase, 0～input voltage, deviation<5%
Output frequency G type:0～600Hz
Output Outputrange
frequency Max frequency ±0.5%
accuracy G type: 150% rated current/1 min, 180% rated current/10s, 200% rated current/0.5s
Overload capacity
P type: 120% rated current/1 min, 140% rated current/10s, 150% rated current/0.5s
Motor type Three-phase asynchronous motor; Permanent magnet synchronous motor (sine wave)
Control mode V/F control, Open loop vector control, Closed loop vector control
Modulation Optimizing Space Voltage Vector PWM Modulation
Carrier frequency 1.0～16.0kHz
Main Speed control range VC without PG: rated load 1:100; VC with PG: rated load 1:1000
Control
Steady speed VC without PG: ≤2% rated synchronized speed; VC with PG: ≤0.05% rated synchronized speed
performance
accuracy
Starting torque VC without PG: 150% rated torque at 0.5Hz; VC with PG: 0Hz, 200% rated torque at 0Hz
Torque response VC without PG:<20ms; VC with PG: <10ms
Frequency accuracy Digital setting: max frequency×±0.01%; Analog setting: max frequency×±0.2%
Frequency resolution Digital setting: 0.01Hz; Analog setting: max frequency×0.05%
Torque control Torque setting calculation, torque mode speed limit
DC braking capacity Starting frequency:0.00～50.00Hz; Braking time:0.0～60.0s; Braking current:0.0～150.0% rated
Torque boost current
Automatic torque boost 0.0%～100.0%; Manual torque boost 0.0%～30.0%
capacity Four modes: linear torque characteristic curve, self-set V/F curve, torque reduction characteristic
V/F curve
curve (1.1 to 2.0 power), square V/F curve
Acceleration/Deceler 2 modes: linear Acceleration/Deceleration and S curve Acceleration/Deceleration. 4 sets of
ation curve ACC/DEC, time unit 0.01s selectable, longest time: 650.00s.
Using the power supply voltage compensation function, the rated voltage of the motor is 100%, which
Rated output voltage
can be set within the range of 50 to 100% (the output cannot exceed the input voltage)
Voltage auto- While power supply voltage fluctuates, it can auto-keep constant output voltage.
adjustment
Auto energy-saving While under V/F control mode, according to load situation, auto-optimize output voltage to save
Basic running energy.
functions
Auto-limit current Auto-limit the current while running to prevent over current break trouble.
Instant power off Uninterrupted operation through bus voltage control during instantaneous power loss
treatment PID control, speed track, power off restart, jump frequency, upper/lower frequency limit control,
Standard functions
program operation, multi- speed, RS485, analog output, frequency impulse output.
Keyboard digital setting, Analog voltage/current terminal AI1, Analog voltage/current terminal AI2,
Frequency setting
Communication given and multi-channel terminal selection, Main and auxiliary channel combination,
channels
expansion card, supporting different modes switch
Feedback input Voltage/Current Terminal AI1, Voltage/Current Terminal AI12, Communication given, Low-speed pulse
channel input PUL, extension card
Running command Operation panel given, external terminal given, communication given, expansion card given
channel
Input command Start, stop, FWD/REV, JOG, multi-step speed, free stop, reset, ACC/DEC time selection, frequency
signal given channel selection, external fault alarm.

3
RD11 Series Frequency converter Manual
External output
1 relay output, 1 collector output, 1 AO output: 0～10V output or 4～20mA output
signal
Overvoltage, under-voltage, current limit, over-current, overload, electric thermal relay, overheat,
Protection function
overvoltage stall, data protection, rapid speed protection, input/output phase failure protection
Built-in keyboard: single line 5- digital tube display monitor 1 inverter status quantity
LED display
External keyboard: double line 5- digital tube display Monitor 2 inverter status quantities
Keyboard Parameter copy Upload and download function code information of the inverter for fast parameter copying
display Output frequency, given frequency, output current, input voltage, output voltage, motor speed, PID
Status monitor
feedback, PID given value, module temperature etc. monitor parameters.
Over-voltage, under-voltage, over-current, short circuit, phase failure, overload, overheat, overvoltage
Error alarm
stall, current limit, or Data protection compromised, current fault health, historical fault record
The altitude is less than 1000 meters, and the derating is more than 1000 meters. The derating is 1%
Install place for every 100 meters. No condensation, icing, rain, snow, hail, etc., solar radiation is less than
700W/m2, air pressure 70~106kPa
Temperature, -10 ～ +50°C, derating can be used above 40 °C, the maximum temperature is 60 °C (no-load
humidity operation), 5%~95%RH(no condensation)
Environment Vibration 5% to 95% RH (no condensation)
9～200Hz,5.9m/s2(0.6g)
Storage temperature 5%—95%RH
-30—+60℃ (no condensation)
Installation Wall hanging
Protection degree IP20
Cooling method Forced air cooling

2 Installation
In order to ensure the safe use of this product by users, maximize the performance of the inverter, and ensure the reliable operation of the
inverter, please strictly use the product in accordance with the environment, wiring, ventilation and other requirements described in this chapter.

Inverter and keyboard dimensions

4
RD11 Series Frequency converter Manual
Overall dimension(mm) Installation dimension(mm) Apertur
Model
W H H1 D D1 W1 W2 H2 A B e

AC310-S2-R75G-B
76 200 192 155 149 65 65 193 5.5 4 3-M4
AC310-S2-1R5G-B

AC310-S2-2R2G-B
100 242 231 155 149 84 86.5 231.5 8 5.5 3-M4
AC310-S2-004G-B

RD11-T4-0003-LO-IP20-BU
RD11-T4-0004-LO-IP20-BU
RD11-T4-0006-LO-IP20-BU
76 200 192 155 149 65 65 193 5.5 4 3-M4
RD11-T4-0003-HO-IP20-BU
RD11-T4-0004-HO-IP20-BU
RD11-T4-0006-HO-IP20-BU
RD11-T4-0013-LO-IP20-BU
RD11-T4-0017-LO-IP20-BU
100 242 231 155 149 84 86.5 231.5 8 5.5 3-M4
RD11-T4-0010-HO-IP20-BU
RD11-T4-0013-HO-IP20-BU
RD11-T4-0025-LO-IP20-BU
RD11-T4-0032-LO-IP20-BU
116 320 307.5 175 169 98 100 307.5 9 6 3-M5
RD11-T4-0017-HO-IP20-BU
RD11-T4-0025-HO-IP20-BU

Overall dimension(mm) Installation dimension(mm)

Model Aperture
W H H1 D D1 W1 W2 H2 B

5
RD11 Series Frequency converter Manual
RD11-T4-0038-LO-IP20-BU
RD11-T4-0045-LO-IP20-BU
RD11-T4-0060-LO-IP20-BU
142 383 372 225 219 125 100 372 6 4-M5
RD11-T4-0032-HO-IP20-BU
RD11-T4-0038-HO-IP20-BU
RD11-T4-0045-HO-IP20-BU
RD11-T4-0075-LO-IP20-N
RD11-T4-0090-LO-IP20-N
172 430 / 225 219 150 150 416.5 7.5 4-M5
RD11-T4-0060-HO-IP20-N
RD11-T4-0075-HO-IP20-N

Inverter dimensions (iron shell)

Overall dimension(mm) Installation dimension(mm)

Model Aperture
W H H1 D W1 H2
RD11-T4-0110-LO-IP20-N
RD11-T4-0150-LO-IP20-N
RD11-T4-0180-LO-IP20-N
240 560 520 310 176 544 4-M6
RD11-T4-0090-HO-IP20-N
RD11-T4-0110-HO-IP20-N
RD11-T4-0150-HO-IP20-N
RD11-T4-0210-LO-IP20-N
RD11-T4-0250-LO-IP20-N
RD11-T4-0180-HO-IP20-N 270 638 580 350 195 615 4-M8
RD11-T4-0210-HO-IP20-N
RD11-T4-0310-LO-IP20-N-DC
RD11-T4-0340-LO-IP20-N-DC
RD11-T4-0250-HO-IP20-N-DC 350 738 680 405 220 715 4-M8
RD11-T4-0310-HO-IP20-N-DC

6
RD11 Series Frequency converter Manual
RD11-T4-0380-LO-IP20-N-DC
RD11-T4-0415-LO-IP20-N-DC
RD11-T4-0470-LO-IP20-N-DC
RD11-T4-0340-HO-IP20-N-DC 360 940 850 480 200 910 4-M16
RD11-T4-0380-HO-IP20-N-DC
RD11-T4-0415-HO-IP20-N-DC
RD11-T4-0520-LO-IP20-N-DC
RD11-T4-0600-LO-IP20-N-DC
RD11-T4-0470-HO-IP20-N-DC 370 1140 1050 545 200 1110 4-M16
RD11-T4-0510-HO-IP20-N-DC

7
RD11 Series Frequency converter Manual
Inverter installation space requirements

150mm以上
通风方向
Ventilation direction
wind

direction

150mm以上
Ventilation
通风方向 direction
左右空间不设限
Left and right space is not limited Up and
上下空间
downdown space
Up and
space

External keyboard shape and opening size Note: LCD keyboard is fully compatible with LED keyboard size and opening size。

62 16
62 16

使用自攻钉ST3*6
Self-tapping Screw
使用自攻钉ST3*6
17.5
17.5
100

17.5
3.5
100

17.5
3.5
49.4
49.4
37.8
37.8

键盘安装开孔尺寸
35.6 49.4 键盘安装开孔尺寸
Keyboard Installation Size
35.6 49.4
AC300П µ
Б Р
Н в
Т э
ј ь
Е М
Н в
Р О
ј °
ї Є
ї Ч
і Я
ґ з
AC300П µ
Б Р
Н в
Т э
ј ь
Е М
Н в
Р О
ј °
ї Є
ї Ч
і Я
ґ з
77 20.8
70
77 20.8
70

Opening Size 119*70 mm

键盘兜开孔尺寸
132.8

119

119*70mm；

键盘兜开孔尺寸
132.8

119

119*70mm；

1.8

AC300П µ
Б Р
Н в
Т э
ј ь ¶ 1.8
Е М Ј Ё
µ 0.75KW-37KWЈ ©
Н в
Р О
ј °
ї Є
ї Ч
і Я
ґ з
Н ј
RD05 Series External keyboard pocket shape and opening size

AC300П µ
Б Р
Н в
Т э
ј ь
Е М
¶ µ
Ј Ё
0.75KW-37KWЈ ©
Н в
Р О
ј °
ї Є
ї Ч
і Я
ґ з
Н ј

8
RD11 Series Frequency converter Manual
Standard Connection Diagram
External Brake Unit

R External DC Reactor
External External DC Rector
Brake
Resistor Short Note1
Piece
MCCB Contactor Intput Reactor
Input Rector Output
OutputReactor
Rector
AC POWER INPUT

(-) (+) (+) PB (+) P1

U
R R U
V M
S S V ~
W
T T W
Shielded cable or armoured cable
VFD
(the end close to VFD grounding)
Note2 +24V E (The grounding resistance
PLC is less than 10 ohms)
Note:Function description in brackets is COM
factory default AC220V MAX Output Of Contact:

Passive contact
TA 3A/240VAC
(Forward) X1 Coil 5A/30VDC

output
TB
(Reverse) X2
Multi function contact input

TC
(FWD JOG) X3
AC0V
(REV JOG) X4
+24V

Open collector(OC)
(Free STOP) X5 Shielded cable
Coil
Y (the end close

state output
PUL
to VFD grounding)
COM
COM
A+ Note:
RS485 Differential 120¦ ё 1.MAX Output of +24V Port:DC24V/100mA
Communication 2.Max Output of Y Port :DC24V/50mA
B-

Shielded cable (the end close to 10

Frequency control input

VFD grounding) +10V _

mA

20
0

Analog monitoring
Analog Voltage/Current quantity input

signal output
AI1 + -
Analog Voltage/Current quantity input Shielded cable (the
AI2 A0
GND end close to VFD
grounding)
GND
Note: 1.MAX Output of +10V port :50mA
Note:When output type of AO port as
2.Inner resistance of AI1/AI2 Port frequency and Voltage,
Maximum Output:2mA
Legend: 1.Symbol represent main circuit terminals;
2.Symbol represent control circuit terminals.

Note: 1. When installing the DC reactor, be sure to remove the shorting tab between the P1 and (+) terminals.
2. The terminal (X1~X5/PUL) can select the NPN or PNP transistor signal as the input, and the bias voltage can select the internal power

supply (+24V terminal) or external power supply (PLC terminal) of the inverter.

● Auxiliary Terminal Output Capacity

Terminal Function Definition Max Output
+10V 10V auxiliary power supply output, constitutes loop with GND. 50mA
A0 Analog monitor output, constitutes loop with GND. Max output 2mA as voltage signal
+24V 24V auxiliary power supply output, constitutes loop with COM. 100mA
Collector open circuit output; can set the action-object by
Y DC24V/50mA
program.
Passive connector output; can set the action-object by
TA/TB/TC 3A/240VAC; 5A/30VDC
program.

9
RD11 Series Frequency converter Manual
● Function Specification of Switch Terminals

Switch Terminal Selecting Position Function Specification

RS485 Terminal Resistor RS485 Communication :connect with 120Ω terminal resistor
AO Output- frequency AO2: 0.0～100kHz frequency output
AO Output- Current AO2: 0～20mA current output or 4～20mA current output
AO Output- Voltage 0～10V voltage output
AI1 Input- Current/Voltage AI1: Input 0～20mA or 0～10V
AI2 Input- Current/Voltage AI2: Input 0～20mA or 0～10V
●Some peripheral electrical components instructions

Name Installation and selection Function Definition

Increase the power factor on the input side;
Installed between the EMC filter and
Improve the overall efficiency and thermal stability of the inverter;
DC reactor the braking resistor
Effectively eliminate the influence of the input side higher harmonics on the
132kW and above standard
inverter and reduce external conduction and radiation interference.
For power models above 22kW, please choose our recommended braking
Standard 22kW and below, 22kW or
unit and braking resistor;
Break unit more to 110kW (connected between
The motor consumes regenerative energy through the braking resistor when
PB and (+))
decelerating.

10
RD11 Series Frequency converter Manual

3 Keyboard Layout and Operating Instructions

●Keyboard Appearance

Integrated keyboard（37KW and below） Double-line keyboard（37KW and above）

●Key function

Integrated Double-line Function

符号 Hz：frequency A：current V：voltage V/A: voltage/current
A Unit indicator
RPM：rotate speed %：ratio
B Status indicator On: Forward running status Blinking: Reverse running status Off: Stopping

Enter the function menu interface during standby or running; press this button
C to exit the modification when the parameter is modified; press the button (1
second) during standby or running to enter the status interface directly.

Confirmation function: After modifying the value, press this key to confirm the
D modification value.
Shift function: long press this button (1 second) to move the operation bit, long
press is not loose, then cyclic shift

E The up key increases the operation value, and the down key decreases the
operation value.
When the run/stop is controlled by the keyboard, press this button to turn the
inverter forward. The status indicator is always on during forward run, and the
status indicator is blinking during reverse run.
F
When the command given channel is keyboard control, press this key to stop
the inverter; the parameter F11.03 [keyboard stop key setting] can be used to
define whether other command channels are valid; when the fault state is
pressed, the inverter resets.
Digital potentiometer: Use clockwise rotation as the upper key to increase the
operation value, counterclockwise rotation as the lower key to reduce the
G operation value.
Confirmation key: After modifying the value, press this key to confirm the
modified value.

11
RD11 Series Frequency converter Manual

Move left and right

H Select the function of this key by parameter F11.00 [Keyboard Multi-Function

Key Selection]

●Basic parameter group setting

The following is an example of setting F01.22 [acceleration time] = 10.00s to explain the basic operation of the LED operator.
PRG short press Up
PRG短按 上键

PRG短按 下键
PRG short press Down

PRG short
PRG短按 press SET

Down
下键 Up
上键

Up
上键 SET

下键 SET
Down

SET

Note: When modifying the ten, hundred and thousand digits of the parameter value, use the keyboard shift key function to quickly select.
● Run monitoring status view

Given frequency Input voltage

输入电压
给定频率
SET

SET SET

SET
Output frequency
输出频率 Output voltage
输出电流

Note: When using the external keyboard, use the left shift button to cycle through the first line of monitoring parameters, and use the right shift button to cycle through the
second line of monitoring parameters.
● Monitoring parameter view
The following is an example to illustrate the basic operation of the LED operator at at C02.05 [PLC Operation Phase
PRG long press
PRG长按 Up
上键

PRG短按 下键
Down

PRG short
PRG短按 press SET

Up
上键
SET

下键
SET Down

12
RD11 Series Frequency converter Manual

4 Function Parameter Table

This chapter only provides a function code summary table. For detailed function description, please refer to the RD11 technical manual or consult
our company.
4.1 Parameter icon description
 Icons and terms that represent control modes

Icon Description
V/F Effective parameters in asynchronous motor V/F control mode
SVC Effective parameters of asynchronous motor open loop vector control
FVC Effective parameters of closed-loop vector control of asynchronous motor
PMVF Effective parameters in synchronous motor V/F control mode
PMSVC Effective parameters of synchronous motor open loop vector control mode
PMFVC Effective parameters of synchronous motor closed-loop vector control mode
Note: The control mode icon has no shadow to indicate that the parameter is invalid in this control mode.
 Icons and terms that represent control modes

Icon Description
RUN Parameters that can be modified during operation
STOP Parameters that cannot be modified during operation
READ This parameter can only be read and cannot be modified (the LED shows 5 "-" when modified)

4.2 Parameter content

parameter name parameter name
F00.0x Environment setting F06.4x Frequency detection
F00.1x Common parameter setting F06.5x Monitor parameter comparator output
F01.0x Basic command F06.6x Virtual input and output terminal
F01.1x Frequency command F07.0x Start control
F01.2x Acc/Dec time F07.1x Shutdown control
F01.4x PWM control F07.2x DC braking and speed tracking
F02.0x Basic motor parameters and self-learning options F07.3x JOG
F02.1x Asynchronous motor advanced parameters F07.4x Start, stop frequency maintenance and frequency hopping
F02.2x Synchronous motor advanced parameters F08.0x Counting and timing
F02.3x Encode parameter F08.3x Swing frequency control
F02.5x Motor application parameter F10.0x Current protection
F03.0x Speed loop F10.1x Voltage protection
F03.1x Current loop and torque limit F10.2x Auxiliary protection
F03.2x Torque optimization control F10.3x Load protection
F03.3x Flux optimization F10.4x Stall protection
F03.4x Torque control F10.5x Failure recovery protection
F03.6x PM high frequency injection F11.0x Key operation
F03.7x Position compensation F11.1x Status interface loop monitoring
F03.8x Extended control F11.2x Monitoring parameter control
F04.0x V/F control F12.0x MODBUS slave parameters
F04.1x Custom V/F curve F12.1x MODBUS host parameters
F04.3x V/F energy saving control F12.3x Profibus-DP parameter
F05.0x Digital input terminal F12.4x CANopen parameter
F05.1x X1-X5 detection delay F12.5x Expansion port EX-A, EX-B communication
F05.2x Digital input terminal action selection F13.00-F13.06 PID given and feedback
F05.3x PUL terminal F13.07-F13.24 PID adjustment
F05.4x Analog (AI) type processing F13.25-F13.28 PID feedback disconnection judgment
F05.5x Analog (AI) linear processing F13.29-F13.33 Sleep function
F05.6x AI curve 1 processing F14.00-F14.14 Multi-speed frequency given
F05.7x AI curve 2 processing F14.15 PLC operation mode selection
F05.8x AI as a digital input terminal F14.16-F14.30 PLC running time selection
F06.0x AO (analog) output F14.31-F14.45 PLC direction and ACC/DEC time selection
F06.1x Extended AO output C00.0x Basic monitoring
F06.2x Digital, relay output C01.0x Fault monitoring

13
RD11 Series Frequency converter Manual
4.3 Environment application
Parameter Factory default Adjustable
Name Content
（Address） (range) properly
V/F SVC FVC PMVF PMSVC PMFVC
Set the parameter access level based on the case of restricted
parameter access.
F00.00 Parameter access 0
0: standard parameter (Fxx.yy) RUN
(0x0000) level (0 ~ 3)
1: Common parameters (F00.00, Pxx.yy)
2: Monitoring parameters (F00.00, Cxx.yy)
3: Changed parameter(F00.00, Hxx.yy)
V/F SVC FVC PMVF PMSVC PMFVC
Set the inverter initialization method.
0: not initialized
F00.03 0
Initialization 11: Select the set value according to the purpose to perform the STOP
(0x0003) （0 ~ 33）
parameter (excluding the motor parameter)
22: All parameters are initialized
33: Clear the fault record
V/F SVC FVC PMVF PMSVC PMFVC
F00.04 Keyboard parameter 0: no function 0
STOP
(0x0004) copy 1: Upload parameters to the keyboard （0 ~ 9999）
2: Download parameters to the inverter
F00.05 V/F SVC FVC PMVF PMSVC PMFVC 0
User password STOP
(0x0005) Used to set the user password. （0 ~ 65355）
V/F SVC FVC PMVF PMSVC PMFVC
F00.06 LCD keyboard 0
Select the language displayed on the LCD operator. RUN
(0x0006) language selection （0 ~ 1）
0: Chinese 1: English
F00.07 V/F SVC FVC PMVF PMSVC PMFVC 0
Free parameter 1 When using multiple machines, use the machine number or usage RUN
(0x0007) （0 ~ 65535）
mode number.
V/F SVC FVC PMVF PMSVC PMFVC
F00.08 0
Free parameter 2 When using multiple machines, use the machine number or usage RUN
(0x0008) （0 ~ 65535）
mode number.
V/F SVC FVC PMVF PMSVC PMFVC
F00.10~F00.3
“0~00” digits: yy setting in function parameter number Fxx.yy
9 Common parameter 0102
00～99 RUN
(0x0010 ~ address setting (0000 ~ 3199)
“000~0000”digits: xx setting in function parameter number Fxx.yy
0x0027)
00~31

4.4 F01：Basic Settings

F01.0x：Basic command
Parameter Factory default Adjustable
Name Content
（Address） (range) properly
V/F SVC FVC PMVF PMSVC PMFVC
The control mode of the motor.
Asynchronous motor control mode:
0: AM-VF; VF control
F01.00 1:AM-SVC; open loop vector control, current closed loop control 0
Motor control STOP
(0x0100) 2: AM-FVC; closed loop vector control (0 ~ 12)
Synchronous motor control mode:
10: PM-VF; VF control
11: PM-SVC; open loop vector control
12: PM-FVC; closed loop vector control
V/F SVC FVC PMVF PMSVC PMFVC
Used to select the channel that the drive accepts the run and stop
F01.01 Run command 0
commands and the direction of travel. RUN
(0x0101) channel （0 ~ 3）
0: keyboard control (external keyboard priority) 1: terminal control
2: RS485 communication control 3: Option card
V/F SVC FVC PMVF PMSVC PMFVC
The given source channel B of the frequency converter
F01.02 Frequency given 0
0: keyboard digital reference frequency 1: keyboard analog RUN
(0x0102) channel A （0 ~ 11）
potentiometer given
2: Current/voltage analog AI1 given

14
RD11 Series Frequency converter Manual
3: Current/voltage analog AI2 given
4: Reserved 5: Terminal pulse PUL given
6: RS485 communication reference 7: Terminal UP/DW control
8: PID control given 9: Program control (PLC) given
10: Optional card 11: Multi-speed speed given
F01.03 Frequency reference V/F SVC FVC PMVF PMSVC PMFVC 100.0
STOP
(0x0103) source channel A gain Frequency reference source channel A gain （0.0 ~ 500.0%）
V/F SVC FVC PMVF PMSVC PMFVC 2
F01.04 Frequency given
The given source channel B of the frequency converter same RUN
(0x0104) channel B （0 ~ 11）
as[F01.02]
F01.05 Frequency reference V/F SVC FVC PMVF PMSVC PMFVC 100.0
STOP
(0x0105) source channel B gain Frequency reference source channel B gain （0.0 ~ 500.0%）
V/F SVC FVC PMVF PMSVC PMFVC
The reference source of frequency given channel B is selected by
F01.06 Frequency channel B 0
this parameter. RUN
(0x0106) reference source （0 ~ 1）
0: reference source with maximum output frequency
1: Use channel A to set the frequency as the reference source
V/F SVC FVC PMVF PMSVC PMFVC
It is used to select the combination mode of the inverter setting
frequency channel A and channel B.
F01.07 Frequency reference 0
0: channel A 1: channel B RUN
(0x0107) source selection （0 ~ 5）
2: Channel A + Channel B. 3: Channel A-channel B
4: Maximum value of channel A and channel B
5: the minimum of channel A and channel B
V/F SVC FVC PMVF PMSVC PMFVC
When this parameter is valid, it is used to set the channel source
frequency channel for each running command channel.
Units: Bundled with Keyboard command Ten
digits: Bundled with Terminal command Hundreds: Bundled
with communication command Thousands: Bundled with optional
Run command card command 0000
F01.08
bundled given 0: no binding 1: keyboard digital given frequency RUN
(0x0108) （0000 ~ DDDD）
frequency 2: Keyboard analog potentiometer given 3: current / voltage analog
AI1 given
4: Current/voltage analog AI2 given 5: Reserved
6: Terminal pulse PUL reference 7: Communication given
8: Terminal UP/DW control 9: PID control given
A: Program control given B: Option card
C: multi-speed reference D: reserved
50Hz
F01.09 Keyboard digital given V/F SVC FVC PMVF PMSVC PMFVC （0.00～upper limit RUN
(0x0109) frequency Used to set and modify the keyboard digital setting frequency.
frequency）

F01.1x：Frequency Command
Parameter Factory default Adjustable
Name Content
（Address） (range) properly
50.00Hz
F01.10 V/F SVC FVC PMVF PMSVC PMFVC (Upper limit
Maximum frequency STOP
(0x010A) The maximum frequency that the frequency converter can set. frequency～
600.00Hz)
V/F SVC FVC PMVF PMSVC PMFVC
Select a given source for the upper limit frequency of the converter.
0: upper limit frequency digital reference 1: keyboard analog
F01.11 Upper frequency potentiometer given 0
RUN
(0x010B) source selection 2: Current/voltage analog AI1 given （0~7）
3: Current/voltage analog AI2 given
4: Reserved 5: Terminal pulse PUL given
6: RS485 communication reference 7: Option card
50.00Hz
F01.12 Upper limit frequency V/F SVC FVC PMVF PMSVC PMFVC （0～Max RUN
(0x010C) digital setting Upper limit frequency given channel when F01.11 is set to 0
frequency）
0.00Hz
F01.13 V/F SVC FVC PMVF PMSVC PMFVC （0～Upper limit
Lower limit frequency RUN
(0x010D) Given a lower frequency limit, the given frequency is limited.
frequency）

15
RD11 Series Frequency converter Manual
F01.2x-F01.3x： Acceleration and deceleration Time
Parameter Factory default Adjustable
Name Content
（Address） (range) properly
V/F SVC FVC PMVF PMSVC PMFVC
F01.20 Acceleration/decelerati Set the reference frequency to calculate the 0
STOP
(0x0114) on time reference acceleration/deceleration time. (0 ~ 2)
0: Maximum frequency 1: Fixed frequency 50Hz 2: Set frequency
V/F SVC FVC PMVF PMSVC PMFVC 2
F01.21
Acceleration time unit The unit of acceleration time setting. STOP
(0x0115) （0 ~ 2）
0:1s 1:0.1s 2:0.01s
V/F SVC FVC PMVF PMSVC PMFVC
The time required for the output frequency to accelerate from 0.00 Hz
F01.22 to the reference frequency. Model related（0.01
Acceleration time 1 1～65000s(F01.21 = 0) RUN
(0x0116) ~ 650.00s）
0.1～6500.0s(F01.21 = 1)
0.01～650.00s(F01.21 = 2)
V/F SVC FVC PMVF PMSVC PMFVC
F01.23 Model related
Deceleration time 1 Time required for the output frequency to decelerate from the RUN
(0x0117) （0.01～650.00s）
reference frequency to 0.00 Hz.
V/F SVC FVC PMVF PMSVC PMFVC
F01.24 Model related
Acceleration time 2 Time required for the output frequency to accelerate from 0.00Hz to RUN
(0x0118) （0.01～650.00s）
the reference frequency
V/F SVC FVC PMVF PMSVC PMFVC
F01.25 Model related
Deceleration time 2 Time required for the output frequency to decelerate from the RUN
(0x0119) （0.01～650.00s）
reference frequency to 0.00 Hz.
V/F SVC FVC PMVF PMSVC PMFVC
F01.26 Model related
Acceleration time 3 Time required for the output frequency to accelerate from 0.00Hz to RUN
(0x011A) （0.01～650.00s）
the reference frequency
F01.27 V/F SVC FVC PMVF PMSVC PMFVC Model related
Deceleration time 3 Time required for the output frequency to decelerate from the RUN
(0x011B) （0.01～650.00s）
reference frequency to 0.00 Hz.
V/F SVC FVC PMVF PMSVC PMFVC Model related
F01.28
Acceleration time 4 Time required for the output frequency to accelerate from 0.00Hz to RUN
(0x011C) （0.01～650.00s）
the reference frequency
V/F SVC FVC PMVF PMSVC PMFVC
F01.29 Model related
Deceleration time 4 Time required for the output frequency to decelerate from the RUN
(0x011D) （0.01～650.00s）
reference frequency to 0.00 Hz.
S curve acceleration V/F SVC FVC PMVF PMSVC PMFVC
F01.30 1
and deceleration S curve acceleration and deceleration selection is valid or invalid STOP
(0x011E) （0~1）
selection 0：invalid 1：valid
F01.31 S curve acceleration V/F SVC FVC PMVF PMSVC PMFVC 0.20s
STOP
(0x011F) start time Set the S curve acceleration start time. （0.00～10.00）
F01.32 S curve acceleration V/F SVC FVC PMVF PMSVC PMFVC 0.20s
STOP
(0x0120) end time Set the S curve acceleration end time （0.00～10.00）
F01.33 S curve deceleration V/F SVC FVC PMVF PMSVC PMFVC 0.20s
STOP
(0x0121) start time Set the S curve deceleration start time. （0.00～10.00）
F01.34 S curve deceleration V/F SVC FVC PMVF PMSVC PMFVC 0.20s
STOP
(0x0122) end time Set the S curve deceleration end time （0.00～10.00）
Switching frequency 0.00Hz
F01.35 between acceleration V/F SVC FVC PMVF PMSVC PMFVC （0.00～Max RUN
(0x0123) time 1 and acceleration Set the frequency switch between Acc time 1 and Acc time 2
frequency）
time 2

F01.4x：PWM Controlling

Parameter Factory default Adjustable

Name Content
（Address） (range) properly
F01.40 V/F SVC FVC PMVF PMSVC PMFVC Model related (1.0～
The carrier frequency RUN
(0x0128) Use to set the switching frequency of the inverter IGBT. 16.0kHz)

16
RD11 Series Frequency converter Manual

V/F SVC FVC PMVF PMSVC PMFVC

Units: Carrier and temperature are associated
0: Independent of temperature 1: Temperature dependent
Tens: carrier is associated with output frequency
F01.41 0: Independent of output frequency 1:Output frequency dependent 1111
PWM control mode RUN
(0x0129) Hundreds: random PWM enable （0000 ~ 1111）
0: Disable 1: Enable
Thousands: PWM modulation
0: Only three-phase modulation is used 1:Automatically switched
between two-phase and three-phase modulation

F01.43 Dead zone V/F SVC FVC PMVF PMSVC PMFVC 306
RUN
(0x012B) compensation gain Dead zone compensation gain （0 ~ 512）

4.5 F02：Motor parameter

F02.0x：Basic parameter and Self-tuning

Parameter Factory default Adjustable
Name Content
（Address） (range) properly
V/F SVC FVC PMVF PMSVC PMFVC
F02.00 Set the type of motor 0
Motor type READ
(0x0200) 0: Asynchronous motor (AM) 1: Permanent magnet synchronous (0 ~ 1)
motor (PM)
F02.01 V/F SVC FVC PMVF PMSVC PMFVC 4
Number of motor poles STOP
(0x0201) Set the number of motor poles （2 ~ 98）
Model related
F02.02 V/F SVC FVC PMVF PMSVC PMFVC （0.1～
Rated power STOP
(0x0202) Set the rated power of the motor.
1000.0kW）
F02.03 V/F SVC FVC PMVF PMSVC PMFVC Model related
Rated frequency STOP
(0x0203) Set the rated power of the motor.。 （0.01～Max）
F02.04 V/F SVC FVC PMVF PMSVC PMFVC Model related
Rated rotate speed STOP
(0x0204) Set the rated rotate speed of the motor. （0～65000rpm）
F02.05 V/F SVC FVC PMVF PMSVC PMFVC Model related
Rated voltage STOP
(0x0205) Set the rated voltage of the motor. （0～1500V）
F02.06 V/F SVC FVC PMVF PMSVC PMFVC Model related
Rated current STOP
(0x0206) Set the rated current of the motor （0.1～3000.0A）
V/F SVC FVC PMVF PMSVC PMFVC
F02.07 Motor parameter self- After the parameter self-tuning is finished, the value of [F02.07] will be 0
automatically set to "0". STOP
(0x0207) tuning selection （0 ~ 3）
0: No operation 1: Rotary self-learning
2: Static self-learning 3: Stator resistance self-learning

F02.1x：Motor Senior Parameter

Parameter Factory default Adjustable
Name Content
（Address） (range) properly

F02.10 Asynchronous motor V/F SVC FVC PMVF PMSVC PMFVC Model related (0.1～
STOP
(0x020A) no-load current Set the size of the no-load current of the asynchronous motor. 3000.0A)
Model related
F02.11 Asynchronous motor V/F SVC FVC PMVF PMSVC PMFVC
(0.01mΩ ～ STOP
(0x020B) stator resistance Set the size of the asynchronous motor stator resistance.
60000mΩ)
Model related
F02.12 Asynchronous motor V/F SVC FVC PMVF PMSVC PMFVC
(0.01mΩ ～ STOP
(0x020C) rotor resistance Set the size of the asynchronous motor rotor resistance.
60000mΩ)
Asynchronous motor Model related
F02.13 V/F SVC FVC PMVF PMSVC PMFVC （0.01mH ～
stator leakage STOP
(0x020D) Set the stator leakage inductance of the asynchronous motor.
inductance 65535mH）

17
RD11 Series Frequency converter Manual
Model related
F02.14 Asynchronous motor V/F SVC FVC PMVF PMSVC PMFVC （0.01mH ～ STOP
(0x020E) stator inductance Set the stator inductance of the asynchronous motor.
65535mH）
Model related
F02.15 Stator resistance V/F SVC FVC PMVF PMSVC PMFVC （0.01 ～ READ
(0x020F) standard value Set the stator resistance value.
50.00%）

F02.16 Rotor resistance V/F SVC FVC PMVF PMSVC PMFVC Model related
READ
(0x0210) standard value Set the rotor resistance value. （0.01～50.00%）

F02.17 Stator leakage V/F SVC FVC PMVF PMSVC PMFVC Model related
READ
(0x0211) inductance Set the stator leakage inductance value。 （0.01～50.00%）

Model related
F02.18 Stator inductance V/F SVC FVC PMVF PMSVC PMFVC （0.1 ～ READ
(0x0212) value Set the stator inductance value
999.0%）

F02.2x：Synchronous Motor Senior Parameter

Parameter Factory default Adjustable

Name Content
（Address） (range) properly
Model related
F02.20 Synchronous stator V/F SVC FVC PMVF PMSVC PMFVC
(0.01mΩ ～ STOP
(0x0214) resistance Set the PM stator resistance.
60000mΩ)
Model related
F02.21 Synchronous machine V/F SVC FVC PMVF PMSVC PMFVC
(0.001mH ～ STOP
(0x0215) D-axis inductance Set the D-axis inductance of the PM.
6553.5mH)
Model related
F02.22 Synchronous machine V/F SVC FVC PMVF PMSVC PMFVC
(0.001mH ～ STOP
(0x0216) Q-axis inductance Set the Q-axis inductance of the PM. .
6553.5mH)
Synchronous machine V/F SVC FVC PMVF PMSVC PMFVC
F02.23 Model related
back electromotive Set the back EMF of the PM. It will only be recognized when the STOP
(0x0217) （0～1500Vv）
force rotation is self-tuning.
Synchronous machine
F02.24 V/F SVC FVC PMVF PMSVC PMFVC Model related
encoder mounting RUN
(0x0218) Set the PM encoder mounting angle. （0.0°～360.0°）
angle
Synchronous machine
F02.25 V/F SVC FVC PMVF PMSVC PMFVC
stator resistance Model related READ
(0x0219) Set the stator resistance value of the PM
standard value
Synchronous machine
F02.26 V/F SVC FVC PMVF PMSVC PMFVC
D-axis inductance Model related READ
(0x021A) Set the D-axis inductance value of the PM
standard value
Synchronous machine
F02.27 V/F SVC FVC PMVF PMSVC PMFVC
Q-axis inductance Model related READ
(0x021B) Set the Q-axis inductance value of the PM.
standard value
F02.28 Synchronous motor V/F SVC FVC PMVF PMSVC PMFVC Model related
STOP
(0x021C) pulse width coefficient Set the pulse width factor of the PM. （00.00～99.99）
F02.3x-F02.4x：Encoder Parameter
Parameter Factory default Adjustable
Name Content
（Address） (range) properly
V/F SVC FVC PMVF PMSVC PMFVC
F02.30 Speed feedback 0
0: Normal ABZ encoder (extension port EX_B) STOP
(0x021E) encoder type (0 ~ 1)
1: rotary transformer (connected to the expansion port EX_B)
F02.31 V/F SVC FVC PMVF PMSVC PMFVC 0
Encoder direction STOP
(0x021F) 0: the same direction 1: the opposite direction (0 ~ 1)
F02.32 ABZ encoder Z pulse V/F SVC FVC PMVF PMSVC PMFVC 1
STOP
(0x0220) detection selection 0：Off 1：On (0 ~ 1)
F02.33 ABZ encoder line V/F SVC FVC PMVF PMSVC PMFVC 1024
STOP
(0x0221) number Set the number of ABZ encoder lines. （1～10000）

F02.34 Number of resolver V/F SVC FVC PMVF PMSVC PMFVC 2

STOP
(0x0222) poles Set the number of resolver poles. （2 ~ 128）
F02.35 Encoder transmission V/F SVC FVC PMVF PMSVC PMFVC 1
RUN
(0x0223) ratio numerator Set the encoder drive ratio numerator. （1 ~ 32767）

18
RD11 Series Frequency converter Manual
F02.36 Encoder gear ratio V/F SVC FVC PMVF PMSVC PMFVC 1
RUN
(0x0224) denominator Set the encoder driven ratio denominator. （1 ~ 32767）
Encoder speed
F02.37 V/F SVC FVC PMVF PMSVC PMFVC 1.0ms
measurement filter RUN
(0x0225) Set the encoder speed measurement filter time （0.0~ 100.0ms）
time
0.500s
F02.38 Encoder disconnection V/F SVC FVC PMVF PMSVC PMFVC （0.100～ RUN
(0x0226) detection time Set the encoder disconnection detection time.
60.000s）

F02.5x：Motor Application Parameter

Parameter Factory default Adjustable
Name Content
（Address） (range) properly
Stator resistance start V/F SVC FVC PMVF PMSVC PMFVC
F02.50 0
learning function 0: Invalid 1: Learn only without updating Greater than 1: Learn and STOP
(0x0232) (0 ~ 3)
selection update
F02.51 Stator resistance start V/F SVC FVC PMVF PMSVC PMFVC 0
RUN
(0x0233) learning coefficient 1 The stator resistance starts the learning factor of 1. (0 ~ 1000)
F02.52 Stator resistance start V/F SVC FVC PMVF PMSVC PMFVC 0
RUN
(0x0234) learning coefficient 2 The stator resistance starts the learning factor of 2. (0 ~ 1000)
F02.53 Stator resistance start V/F SVC FVC PMVF PMSVC PMFVC 0
RUN
(0x0235) learning coefficient 3 The stator resistance starts the learning factor of 3. (0 ~ 1000)
V/F SVC FVC PMVF PMSVC PMFV
Synchronous motor Units: closed loop vector
F02.60 3010
magnetic pole search 0: Off 1: On 2: On, only for the first time after power-on STOP
(0x023C) (0000~3223)
function Tens: open loop vector
0: Off 1: On 2: On, only for the first time after power-on

4.6 F03：Vector Controlling

F03.0x：Speed loop

Parameter Factory default Adjustable

Name Content
（Address） (range) properly
V/F SVC FVC PMVF PMSVC PMFVC
F03.00 ASR speed rigidity 0
Set the rigidity level, and the higher the level, the better the speed RUN
(0x0300) level (0 ~100)
rigidity.
F03.01 V/F SVC FVC PMVF PMSVC PMFVC 0000
ASR speed rigid mode RUN
(0x0301) ASR speed rigid mode (0000～1111)
F03.02 ASR (speed loop) V/F SVC FVC PMVF PMSVC PMFVC 10.00
RUN
(0x0302) proportional gain 1 Set the ASR (speed loop) proportional gain 1. (0.01 ~ 100.00)
F03.03 ASR (speed loop) V/F SVC FVC PMVF PMSVC PMFVC 0.100s
RUN
(0x0303) integration time 1 Set the ASR (speed loop) integration time 1. （0.000～6.000s）
F03.04 V/F SVC FVC PMVF PMSVC PMFVC 0.0ms
ASR filtering time 1 RUN
(0x0304) Set the ASR filter time 1. （0.0～100.0ms）
F03.05 ASR switching V/F SVC FVC PMVF PMSVC PMFVC 0.00Hz
RUN
(0x0305) frequency 1 Set the ASR switching frequency 1 （0.00～Max）
F03.06 ASR (speed loop) V/F SVC FVC PMVF PMSVC PMFVC 10.00
RUN
(0x0306) proportional gain 2 Set the ASR (speed loop) proportional gain 2. (0.01 ~ 100.00)

F03.07 ASR (speed loop) V/F SVC FVC PMVF PMSVC PMFVC 0.100s
RUN
(0x0307) integration time 2 Set the ASR (speed loop) integration time 2. （0.000～6.000s）
F03.08 V/F SVC FVC PMVF PMSVC PMFVC 0.0ms
ASR filtering time 2 RUN
(0x0308) Set the ASR filter time 2. （0.0～100.0ms）
F03.09 ASR switching V/F SVC FVC PMVF PMSVC PMFVC 0.00Hz
RUN
(0x0309) frequency 2 Set the ASR switching frequency 2. （0.00～Max）

F03.1x：Current Loop and Torque limit

Parameter Factory default Adjustable
Name Content
（Address） (range) properly
F03.10 Current loop D-axis V/F SVC FVC PMVF PMSVC PMFVC 1.00
RUN
(0x030A) proportional gain Set the current loop D-axis proportional gain (0.001 ~ 4.000)

19
RD11 Series Frequency converter Manual
F03.11
Current loop D-axis V/F SVC FVC PMVF PMSVC PMFVC 1.00
(0x030B) RUN
integral gain Set the current loop D-axis integral gain (0.001 ~ 4.000)
RUN
F03.12 Current loop Q-axis V/F SVC FVC PMVF PMSVC PMFVC 1.00
RUN
(0x030C) proportional gain Set the current loop Q-axis proportional gain (0.001 ~ 4.000)

F03.13 Current loop Q-axis V/F SVC FVC PMVF PMSVC PMFVC 1.00
RUN
(0x030D) integral gain Set the current loop Q-axis integral gain (0.001 ~ 4.000)

F03.15 Electric state torque V/F SVC FVC PMVF PMSVC PMFVC 250.0%
RUN
(0x030E) limit Set the motor state torque limit. （0.0～400.0%）

F03.16 Power generation V/F SVC FVC PMVF PMSVC PMFVC 250.0%
RUN
(0x030F) torque limit Set the power generation torque limit （0.0～400.0%）

F03.17 Regenerative torque V/F SVC FVC PMVF PMSVC PMFVC 0.0%
RUN
(0x0312) limit at low speed Set the regenerative torque limit at low speed （0.0～400.0%）
Torque limit action
F03.18 V/F SVC FVC PMVF PMSVC PMFVC 6.00s
frequency amplitude at RUN
(0x0313) Set the torque limit action frequency amplitude at low speed （0.00～30.00s）
low speed

F03.2x：Torque Optimization Controlling

Parameter Factory default Adjustable

Name Content
（Address） (range) properly

F03.20 Synchronous motor V/F SVC FVC PMVF PMSVC PMFVC

20.0%
(0x0314) low frequency pull-in The PM motor open loop control is effective, and the larger the pull- RUN
(0.0 ~ 50.0%)
current in current is, the larger the torque output is.。
Synchronous motor V/F SVC FVC PMVF PMSVC PMFVC
F03.21 10.0%
high frequency pull-in The PM motor open loop control is effective, and the larger the pull- RUN
(0x0315) (0.0 ~ 50.0%)
current in current is, the larger the torque output is.
F03.22 Synchronous motor V/F SVC FVC PMVF PMSVC PMFVC 10.0%
pull-in current RUN
(0x0316) The set value 100.0% corresponds to F01.10 [maximum frequency]. (0.0 ~ 100.0%)
frequency
F03.23 Asynchronous motor V/F SVC FVC PMVF PMSVC PMFVC 100.0%
RUN
(0x0317) slip compensation Set the asynchronous motor speed slip compensation. (0.0 ~ 250.0%)

F03.24 Starting torque initial V/F SVC FVC PMVF PMSVC PMFVC 0.0%
RUN
(0x0318) value Set the initial value of the starting torque (0.0 ~ 250.0%)

F03.3x：Magnetic Flux Optimization

Parameter Factory default Adjustable

Name Content
（Address） (range) properly
F03.30 Weak magnetic feed V/F SVC FVC PMVF PMSVC PMFVC 10.0%
RUN
(0x031E) forward coefficient Set the weak magnetic feed forward coefficient (0.0 ~500.0%)
F03.31 Weak magnetic control V/F SVC FVC PMVF PMSVC PMFVC 10.0%
RUN
(0x031F) gain Set the weak magnetic control gain (0.0 ~ 500.0%)
F03.32 Weak magnetic current V/F SVC FVC PMVF PMSVC PMFVC 60.0%
RUN
(0x0320) upper limit Set the weak magnetic current upper limit (0.0 ~ 250.0%)
F03.33 Weak magnetic V/F SVC FVC PMVF PMSVC PMFVC 97.0%
RUN
(0x0321) voltage coefficient Set the weak magnetic voltage coefficient (0.0 ~ 120.0%)
F03.34 V/F SVC FVC PMVF PMSVC PMFVC 250.0%
Output power limit RUN
(0x0322) Set the output power limit (0.0 ~ 400.0%)
F03.35 Overexcitation braking V/F SVC FVC PMVF PMSVC PMFVC 100.0%
RUN
(0x0323) gain Set the overexcitation braking gain (0.0 ~ 500.0%)
F03.36 Overexcitation braking V/F SVC FVC PMVF PMSVC PMFVC 10.0%
RUN
(0x0324) limit Set the overexcitation braking limit (0.0 ~ 250.0%)
F03.37 Energy efficient V/F SVC FVC PMVF PMSVC PMFVC 0
RUN
(0x0325) operation 0：Off 1：On (0 ~ 1)
Energy-saving
F03.38 V/F SVC FVC PMVF PMSVC PMFVC 50.0%
operation excitation RUN
(0x0326) Set the Energy-saving operation excitation lower limit (0.0 ~ 80.0%)
lower limit
Energy-saving
F03.39 V/F SVC FVC PMVF PMSVC PMFVC 0.010s
operating filter RUN
(0x0327) Set the Energy-saving operating filter coefficient (0.000 ~ 6.000s)
coefficient

20
RD11 Series Frequency converter Manual

F03.4x-F03.5x： Torque Controlling

Parameter Factory default Adjustable
Name Content
（Address） (range) properly
V/F SVC FVC PMVF PMSVC PMFVC
F03.40 Torque control 0
0：speed control mode torque limited 1：torque control mode RUN
(0x0328) selection (0 ~ 1)
speed limited
V/F SVC FVC PMVF PMSVC PMFVC
Unit: Channel A Ten: Channel B
0: Keyboard number given 1: Reserved
2: Current/voltage analog AI1 given
3: Current/voltage analog AI2 given
F03.41 Torque command 4: Reserved 5: PUL 0000
RUN
(0x0329) given 6: RS485 communication reference 7: Option card (0000~0577)
Hundreds: command given mode
0: channel A 1: channel B
2: Channel A + Channel B 3: Channel A - Channel B
4: Minimum value of channel A and channel B
5: Maximum value of channel A and channel B
F03.42 Torque keyboard digital V/F SVC FVC PMVF PMSVC PMFVC 0.0%
RUN
(0x032A) setting Set the torque command given (0.0 ~ 100.0%)
F03.43 V/F SVC FVC PMVF PMSVC PMFVC 0.00%
Torque input lower limit RUN
(0x032B) Set the torque input lower limit. (0.0 ~ 100.00%)
F03.44 Lower limit V/F SVC FVC PMVF PMSVC PMFVC 0.0%
RUN
(0x032C) corresponding setting Set the lower limit corresponding value. （-200.0～200.0%）
F03.45 V/F SVC FVC PMVF PMSVC PMFVC 100.0%
Torque input upper limit RUN
(0x032D) Set the upper limit of the torque input. （0.0～100.0%）
F03.46 Upper limit V/F SVC FVC PMVF PMSVC PMFVC 100.0%
RUN
(0x032E) corresponding setting Set the upper limit corresponding value. （-200.0～200.0%）
F03.47 V/F SVC FVC PMVF PMSVC PMFVC 0.100s
Torque filtering time RUN
(0x032F) Set the torque limit action frequency range at low speed. （0.000～6.000s）
F03.52 V/F SVC FVC PMVF PMSVC PMFVC 150.0%
Output torque limit RUN
(0x0334) Set the upper limit of the output torque. (0.0 ~ 200.0%)
F03.53 Output torque lower V/F SVC FVC PMVF PMSVC PMFVC 0.0%
RUN
(0x0335) limit Set the lower limit of the output torque. (0.0 ~ 200.0%)
V/F SVC FVC PMVF PMSVC PMFVC
0: function code F03.56 setting; 1: reserved
F03.54 Torque control forward 0
2: AI1×F03.56; 3: AI2×F03.56; RUN
(0x0336) speed limit selection （0 ~ 7）
4: Reserved 5: PUL × F03.56;
6: RS485 communication given × F03.56 7: Option card × F03.57
V/F SVC FVC PMVF PMSVC PMFVC
0: Function code F03.57 setting; 1 reserved
F03.55 Torque control reverse 0
2: AI1×F03.57; 3: AI2×F03.57; RUN
(0x0337) speed limit selection （0 ~ 7）
4: Reserved 5: PUL × F03.57;
6: RS485 communication given × F03.57 7: Option card × F03.57
Torque control forward
F03.56 V/F SVC FVC PMVF PMSVC PMFVC 100.0%
speed maximum RUN
(0x0338) Set the torque control forward maximum speed limit. （0.0～100.0%）
speed limit
F03.57 Torque control reverse V/F SVC FVC PMVF PMSVC PMFVC 100.0%
RUN
(0x0339) maximum speed limit Set the torque control reverse maximum speed limit. （0.0～100.0%）

F03.6x： PM High Frequency Injection

Parameter Factory default Adjustable
Name Content
（Address） (range) properly
V/F SVC FVC PMVF PMSVC PMFVC
F03.60 High frequency Valid under PM motor open loop control 0
STOP
(0x033C) injection selection 0: Disabled 1~5: Enable. The larger the value, the higher the (0 ~ 5)
frequency injected.
V/F SVC FVC PMVF PMSVC PMFVC
F03.61 High frequency 10.0%
Injection voltage amplitude, related to rated voltage, self-learning RUN
(0x033D) injection voltage (0.0 ～ 100.0%)
results, generally do not need to be modified.

21
RD11 Series Frequency converter Manual
V/F SVC FVC PMVF PMSVC PMFVC
High frequency
F03.62 The frequency range of the high frequency injection is relatively 10.0%
injection cutoff RUN
(0x033E) high, and the high frequency injection is effective when the motor (0.0 ～ 100.0%)
frequency
speed is less than this value.
V/F SVC FVC PMVF PMSVC PMFVC
F03.70 Position compensation 0.0
Position compensation control under speed control for zero servo RUN
(0x0346) control (0 ~ 250.0)
or increased system rigidity
F03.71 V/F SVC FVC PMVF PMSVC PMFVC 1.0
Compensation gain RUN
(0x0347) Set compensation gain (0.0 ～ 100.0)
F03.72 Compensation V/F SVC FVC PMVF PMSVC PMFVC 0.0%
STOP
(0x0348) amplitude limit Set the compensation amplitude limit value. (0.0 ～ 100.0%)
F03.73 V/F SVC FVC PMVF PMSVC PMFVC 10.0%
Compensation range STOP
(0x0349) Set the compensation range. (0.0 ～ 100.0%)
F03.80 Synchronous motor V/F SVC FVC PMVF PMSVC PMFVC 100.0%
RUN
(0x0350) MTPA gain Set the synchronous motor MTPA gain. (0.0 ~ 400.0%)
F03.81 Synchronous motor V/F SVC FVC PMVF PMSVC PMFV 1.0ms
RUN
(0x0351) MTPA filter time Set the MTPA filter time of the synchronous motor. (0.0 ～ 100.0ms)

4.7 F04 ：V/F Controlling

F04.0x：V/F Controlling
Parameter Factory default Adjustable
Name Content
（Address） (range) properly
V/F SVC FVC PMVF PMSVC PMFVC
Used to select the type of V/F curve to meet different load
F04.00 Linear VF curve 0
characteristics. STOP
(0x0400) selection (0 ~ 11)
0: straight VF curve; 1-9: respectively, a power curve of 1.1-1.9 VF;
10: square VF curve; 11: customize VF curve;

F04.01 V/F SVC FVC PMVF PMSVC PMFVC 0.0%

Torque boost RUN
(0x0401) 0.0%: automatic torque boost; 0.1 to 30.0%: manual torque boost (0.0 ～ 30.0%)

V/F SVC FVC PMVF PMSVC PMFVC

F04.02 Torque boost cutoff Set the effective range of the torque boost function. When the 100.0%
RUN
(0x0402) frequency output frequency exceeds this value, the torque boost function is (0.0 ～ 100.0%)
cut off.
F04.03 V/F SVC FVC PMVF PMSVC PMFVC 0.0%
Slip compensation gain RUN
(0x0403) Set the slip compensation gain. (0.0 ~ 200.0%)

F04.04 V/F SVC FVC PMVF PMSVC PMFVC 100.0%

Slip compensation limit RUN
(0x0404) Set the slip compensation limit value. (0.0 ~ 300.0%)
V/F SVC FVC PMVF PMSVC PMFVC
F04.05 Slip compensation filter The slip compensation function needs to correctly input the motor 0.200
RUN
(0x0405) time nameplate parameters and learn the parameters to achieve the （0.000 ~ 6.000）
best results.
V/F SVC FVC PMVF PMSVC PMFVC
F04.06 Oscillation suppression By adjusting this value, low frequency resonance can be 100.0%
RUN
(0x0406) gain suppressed, but not too large, otherwise it will cause additional （0.0 ~ 900.0%）
stability problems.。
F04.07 Oscillation suppression V/F SVC FVC PMVF PMSVC PMFVC 1.0
RUN
(0x0407) filter time Set the oscillation suppression filter time. (0.0 ~ 100.0s)

F04.08 Output voltage V/F SVC FVC PMVF PMSVC PMFVC 100.0%s
STOP
(0x0408) percentage Set the output voltage percentage （25.0～120.0%）

F04.1x: Custom V/F Curve

Parameter Factory default Adjustable

Name Content
（Address） (range) properly
F04.10 V/F SVC FVC PMVF PMSVC PMFVC 3.0%
Self-setting voltage V1 STOP
(0x040A) Self-setting voltage V1 (0.0 ~ 100.0%)

22
RD11 Series Frequency converter Manual
F04.11 V/F SVC FVC PMVF PMSVC PMFVC 1.00Hz
Self-set frequency F1 STOP
(0x040B) Self-set frequency F1 (0.00~Max)
F04.12 V/F SVC FVC PMVF PMSVC PMFVC 28.0%
Self-setting voltage V2 STOP
(0x040C) Self-setting voltage V2 (0.0 ～ 100.0%)
F04.13 V/F SVC FVC PMVF PMSVC PMFVC 10.0Hz
Self-set frequency F2 STOP
(0x040D) Self-set frequency F2 (0.00~ Max)
F04.14 V/F SVC FVC PMVF PMSVC PMFVC 55.0%
Self-setting voltage V3 STOP
(0x040E) Self-setting voltage V3 (0.0 ~ 100.0%)
F04.15 V/F SVC FVC PMVF PMSVC PMFVC 25.00Hz
Self-set frequency F3 STOP
(0x040F) Self-set frequency F3 (0.00~ Max)
F04.16 V/F SVC FVC PMVF PMSVC PMFVC 78.0%
Self-setting voltage V4 STOP
(0x0410) Self-setting voltage V4 （0.0 ~ 900.0%）
F04.17 V/F SVC FVC PMVF PMSVC PMFVC 37.5Hz
Self-set frequency F4 STOP
(0x0411) Self-set frequency F4 (0.00~ Max)
F04.18 V/F SVC FVC PMVF PMSVC PMFVC 100.0%s
Self-setting voltage V5 STOP
(0x0412) Self-setting voltage V5 （0.0～100.0%）
F04.19 V/F SVC FVC PMVF PMSVC PMFVC 50.0Hz
Self-set frequency F5 STOP
(0x0413) Self-set frequency F5 (0.00~ Max)

F04.2x：Reserved

F04.3x：V/F Energy Saving Controlling

Parameter Factory default Adjustable
Name Content
（Address） (range) properly
F04.30 Automatic energy V/F SVC FVC PMVF PMSVC PMFVC 0
STOP
(0x041E) saving control 0：Off 1：On (0 ~ 1)
Energy saving step-
F04.31 V/F SVC FVC PMVF PMSVC PMFVC 15.0Hz
down frequency lower STOP
(0x041F) Set the lower limit of the energy saving step-down frequency. (0.0～50.0Hz)
limit
Energy-saving step- 50.0%
F04.32 V/F SVC FVC PMVF PMSVC PMFVC
down voltage lower STOP
(0x0420) Set the lower limit of the energy-saving step-down voltage. (20.0～100.0%)
limit
F04.33 Energy-saving step- V/F SVC FVC PMVF PMSVC PMFVC 0.010V/MS (0.000～
RUN
(0x0421) down voltage Set the energy-saving step-down voltage regulation rate. 0.200 V/MS)
F04.34 V/F SVC FVC PMVF PMSVC PMFVC 0.20V/MS (0.00～
Adjustment rate RUN
(0x0422) Set the energy saving voltage recovery rate. 2.00 V/MS)

4.8 F05：Input Terminal

F05.0x：Digital Input Terminal Function

Parameter Factory default Adjustable
Name Content
（Address） (range) properly
F05.00 Terminal X1 function V/F SVC FVC PMVF PMSVC PMFVC 1
selection STOP
(0x0500) See the function of the terminal for details. (0 ~ 95)

F05.01 Terminal X2 function V/F SVC FVC PMVF PMSVC PMFVC 2

selection STOP
(0x0501) See the function of the terminal for details. (0 ~ 95)
F05.02 Terminal X3 function V/F SVC FVC PMVF PMSVC PMFVC 4
STOP
(0x0502) selection See the function of the terminal for details. (0 ~ 95)
F05.03 Terminal X4 function V/F SVC FVC PMVF PMSVC PMFVC 5
selection STOP
(0x0503) See the function of the terminal for details. (0 ~ 95)
F05.04 Terminal X5 function V/F SVC FVC PMVF PMSVC PMFVC 6
selection STOP
(0x0504) See the function of the terminal for details. (0 ~ 95)
F05.05 Terminal X6 function V/F SVC FVC PMVF PMSVC PMFVC 0
selection STOP
(0x0505) See the function of the terminal for details. (0 ~ 95)
F05.06 Terminal X7 function V/F SVC FVC PMVF PMSVC PMFVC 0
selection STOP
(0x0506) See the function of the terminal for details. (0 ~ 95)

23
RD11 Series Frequency converter Manual
F05.07 Terminal X8 function V/F SVC FVC PMVF PMSVC PMFVC 0
selection STOP
(0x0507) See the function of the terminal for details. (0 ~ 95)
F05.08 Terminal X9 function V/F SVC FVC PMVF PMSVC PMFVC 0
selection STOP
(0x0508) See the function of the terminal for details. (0 ~ 95)
F05.09 Terminal X10 function V/F SVC FVC PMVF PMSVC PMFVC 0
selection STOP
(0x0509) See the function of the terminal for details. (0 ~ 95)

F05.1x：Detection Delay
Parameter Factory default Adjustable
Name Content
（Address） (range) properly
V/F SVC FVC PMVF PMSVC PMFVC
F05.10 X1 effective detection 0.010
The delay time corresponding to the input terminal X1 transit from the RUN
(0x050A) delay (0.000 ~ 6.000s)
inactive state to the active state
V/F SVC FVC PMVF PMSVC PMFVC
F05.11 X1 invalid detection 0.010
The delay time corresponding to the input terminal X1 transit from the RUN
(0x050B) delay (0.000 ~ 6.000s)
active state to the inactive state
V/F SVC FVC PMVF PMSVC PMFVC
F05.12 X2 effective detection 0.010
The delay time corresponding to the input terminal X2 transit from the RUN
(0x050C) delay (0.000 ~ 6.000s)
inactive state to the active state
V/F SVC FVC PMVF PMSVC PMFVC
F05.13 X2 invalid detection 0.010
The delay time corresponding to the input terminal X2 transit from the RUN
(0x050D) delay (0.000 ~ 6.000s)
active state to the inactive state
V/F SVC FVC PMVF PMSVC PMFVC
F05.14 X3 effective detection 0.010
The delay time corresponding to the input terminal X3 transit from the RUN
(0x050E) delay (0.000 ~ 6.000s)
inactive state to the active state
V/F SVC FVC PMVF PMSVC PMFVC
F05.15 X3 invalid detection 0.010
The delay time corresponding to the input terminal X3 transit from the RUN
(0x050F) delay (0.000 ~ 6.000s)
active state to the inactive state
V/F SVC FVC PMVF PMSVC PMFVC
F05.16 X4 effective detection 0.010
The delay time corresponding to the input terminal X4 transit from the RUN
(0x0510) delay (0.000 ~ 6.000s)
inactive state to the active state
V/F SVC FVC PMVF PMSVC PMFVC
F05.17 X4 invalid detection 0.010
The delay time corresponding to the input terminal X4 transit from the RUN
(0x0511) delay (0.000 ~ 6.000s)
active state to the inactive state
V/F SVC FVC PMVF PMSVC PMFVC
F05.18 X5 effective detection 0.010
The delay time corresponding to the input terminal X5 transit from the RUN
(0x0512) delay (0.000 ~ 6.000s)
inactive state to the active state
V/F SVC FVC PMVF PMSVC PMFVC
F05.19 X5 invalid detection 0.010
The delay time corresponding to the input terminal X5 transit from the RUN
(0x0513) delay (0.000 ~ 6.000s)
active state to the inactive state

F05.2x：Terminal Movement Selection

Parameter Factory default Adjustable
Name Content
（Address） (range) properly
V/F SVC FVC PMVF PMSVC PMFVC
F05.20 0: Two-wire system 1: Two-wire system 2 0
Terminal control mode STOP
(0x0514) 2: Three-wire system 1 3: Three-wire system 2 (0 ~ 3)
Note: See Appendix 2 for terminal wiring.
V/F SVC FVC PMVF PMSVC PMFVC
X1 ~ X4 terminal
F05.22 0:Valid when closed 1: valid when disconnected 0000
characteristics RUN
(0x0516) Unit: X1 terminal Ten: X2 terminal (0000 ~ 1111)
selection
Hundreds place: X3 terminal Thousands: X4 terminal
V/F SVC FVC PMVF PMSVC PMFVC
X5 ~ X8 terminal
F05.23 0:Valid when closed 1: valid when disconnected 0000
characteristics RUN
(0x0517) Unit: X5 terminal Ten: X6 terminal (0000 ~ 1111)
selection
Hundreds place: X7 terminal Thousands: X8 terminal
X9 ~ X10 terminal V/F SVC FVC PMVF PMSVC PMFVC
F05.24 0000
characteristics 0:Valid when closed 1: valid when disconnected RUN
(0x0518) (0000 ~ 1111)
selection Unit: X9 terminal Ten: X10 terminal
V/F SVC FVC PMVF PMSVC PMFVC
F05.25 Terminal UP/DW 0：The frequency will be stored when power down 1： 0
STOP
(0x0519) control selection The frequency won’t be stored when power down (0 ~ 2)
2：Adjustable during operation stop and clean

24
RD11 Series Frequency converter Manual
Terminal UP/DW
V/F SVC FVC PMVF PMSVC PMFVC
F05.26 controls frequency 0.50Hz/s
Set terminal UP/DW to control the frequency increase and decrease RUN
(0x051A) increase and decrease (0.01~50.00Hz/s)
rate
rate
F05.27 Terminal emergency V/F SVC FVC PMVF PMSVC PMFVC 1.00s
RUN
(0x051B) stop deceleration time Set terminal emergency stop deceleration time (0.01～650.00s)

F05.3x: PUL Terminal

Parameter Factory default Adjustable
Name Content
（Address） (range) properly
V/F SVC FVC PMVF PMSVC PMFVC
F05.30 0: X5 (maximum 5.000KHz) 0
PUL source STOP
(0x051E) 1: Expansion port X10 (maximum 100.00KHz) (0 ~ 2)
2: X5 (maximum 100.00KHz)
V/F SVC FVC PMVF PMSVC PMFVC
F05.31 PUL input minimum The minimum frequency accepted by the PUL, below the frequency 0.00kHz
RUN
(0x051F) frequency signal of this value, the frequency converter will be processed at the (0.00~500.00kHz)
minimum frequency.
PUL minimum
F05.32 V/F SVC FVC PMVF PMSVC PMFVC 0.00%
frequency RUN
(0x0520) Corresponding to the percentage of the set value (0.00～100.00%)
corresponding setting
V/F SVC FVC PMVF PMSVC PMFVC
The maximum frequency accepted by the PUL, above the frequency
F05.33 PUL input maximum signal of this value, the frequency converter will process at the 50.00kHz
RUN
(0x0521) frequency maximum frequency。 (0.00~500.00kHz)
0.00～50.000kHz
PUL maximum
F05.34 V/F SVC FVC PMVF PMSVC PMFVC 100.00%
frequency RUN
(0x0522) Corresponding to the percentage of the set value (0.00～100.00%)
corresponding setting
V/F SVC FVC PMVF PMSVC PMFVC
F05.35 0.100s
PUL filter time The size of the input pulse signal is filtered to eliminate the RUN
(0x0523) (0.000～9.000s)
interference signal。
V/F SVC FVC PMVF PMSVC PMFVC
F05.36 0.010kHz
PUL cutoff frequency Below the frequency of this parameter, the drive is no longer RUN
(0x0524) (0.000~1.000kHz)
recognized. Processed at 0 Hz.。

F05.4x：Analog Input （AI） Treatment

Parameter Factory default Adjustable
Name Content
（Address） (range) properly
F05.40 AI input signal type V/F SVC FVC PMVF PMSVC PMFVC 0
RUN
(0x0528) selection method 0: DIP switch 1: parameter setting (0 ～ 1)
F05.41 V/F SVC FVC PMVF PMSVC PMFVC 0
AI1 input signal type RUN
(0x0529) 0：Voltage range 0~10.00V1：Current range0~20.00mA (0 ～ 1)
F05.42 V/F SVC FVC PMVF PMSVC PMFVC 0
AI2 input signal type RUN
(0x052A) 0：Voltage range 0~10.00V1：Current range0~20.00mA (0 ～ 1)
V/F SVC FVC PMVF PMSVC PMFVC
F05.43 Analog input curve 0000
Units：AI1 Tens：AI2 RUN
(0x052B) selection (0000~0022)
0: straight line (default) 1: curve 1 2: curve 2
V/F SVC FVC PMVF PMSVC PMFVC
F05.50 0.0%
AI1 lower limit Define the signal received by the AI1 terminal. The voltage signal RUN
(0x0532) (0.0～100.0%)
below this value is processed by the limit value.

F05.51 AI1 lower limit V/F SVC FVC PMVF PMSVC PMFVC 0.00%
RUN
(0x0533) corresponding setting Set the percentage of the corresponding set value (-100.00~100.00%)

V/F SVC FVC PMVF PMSVC PMFVC

F05.52 100.0%
AI1 upper limit Define the signal received by the AI1 terminal. The voltage signal RUN
(0x0534) (0.0～100.0%)
higher than this value is processed according to the upper limit value.

F05.53 AI1 upper limit V/F SVC FVC PMVF PMSVC PMFVC 100.00%
RUN
(0x0535) corresponding setting Set the percentage of the corresponding set value (-100.00~100.00%)
V/F SVC FVC PMVF PMSVC PMFVC 0.010s
F05.54
AI1 filtering time Define the size of the analog signal to be used to eliminate interfering RUN
(0x0536) (0.000～6.000s)
signals.

25
RD11 Series Frequency converter Manual
V/F SVC FVC PMVF PMSVC PMFVC
F05.55 0.0%
AI2 lower limit Define the signal received by the AI2 terminal，The voltage signal RUN
(0x0537) (0.00～100.0%)
below this value is processed by the limit value.
F05.56 AI2 lower limit V/F SVC F VC PMVF PMSVC PMFVC 0.00%
RUN
(0x0538) corresponding setting Set the percentage of the corresponding set value (-100.00~100.00%)
V/F SVC FVC PMVF PMSVC PMFVC
F05.57 100.0%
AI2 upper limit Define the signal received by the AI2 terminal. The voltage signal RUN
(0x0539) (0.0～100.0%)
higher than this value is processed according to the upper limit value.
F05.58 AI2 upper limit V/F SVC FVC PMVF PMSVC PMFVC 100.00%
RUN
(0x053A) corresponding setting Set the percentage of the corresponding set value (-100.00~100.00%)
V/F SVC FVC PMVF PMSVC PMFVC
F05.59 0.010s
AI2 filter time Define the size of the analog signal to be used to eliminate interfering RUN
(0x053B) (0.000～6.000s)
signals.
F05.60 V/F SVC FVC PMVF PMSVC PMFVC 0.0%
Curve 1 lower limit RUN
(0x053C) Set the lower limit of curve 1 (0.0 ~ 100.0%)

F05.61 Curve 1 lower limit V/F SVC FVC PMVF PMSVC PMFVC 0.00%
RUN
(0x053D) corresponding setting Set the corresponding percentage (0.00 ~ 100.00%)

F05.62 Curve 1 inflection point V/F SVC FVC PMVF PMSVC PMFVC 30.0%
RUN
(0x053E) 1 input voltage Set curve 1 inflection point 1 input voltage (0.0 ~ 100.0%)
F05.63 Curve 1 inflection point V/F SVC FVC PMVF PMSVC PMFVC 30.00%
RUN
(0x053F) 1 corresponding setting Set the corresponding percentage (0.00～100.00%)
F05.64 Curve 1 inflection point V/F SVC FVC PMVF PMSVC PMFVC 60.0%
RUN
(0x0540) 2 input voltage Set curve 1 inflection point 2 input voltage (0.0 ~ 100.0%)
F05.65 Curve 1 inflection point V/F SVC FVC PMVF PMSVC PMFVC 60.00%
RUN
(0x0541) 2 corresponding setting Set the corresponding percentage (0.00～100.00%)
F05.66 V/F SVC FVC PMVF PMSVC PMFVC 100.0%
Curve 1 upper limit RUN
(0x0542) Set the upper limit of curve 1 (0.0～100.0%)
F05.67 Curve 1 upper limit V/F SVC FVC PMVF PMSVC PMFVC 100.00%
RUN
(0x0543) corresponding setting Set the corresponding percentage (0.00 ~ 100.00%)

F05.70 V/F SVC FVC PMVF PMSVC PMFVC 0.0%

Curve 2 lower limit RUN
(0x0546) Set the lower limit of curve 2 (0.0 ~ 100.0%)

F05.71 Curve 2 lower limit V/F SVC FVC PMVF PMSVC PMFVC 0.00%
RUN
(0x0547) corresponding setting Set the corresponding percentage (0.00 ~ 100.00%)

F05.72 Curve 2 inflection point V/F SVC FVC PMVF PMSVC PMFVC 30.0%
RUN
(0x0548) 1 input voltage Set curve 2 inflection point 1 input voltage (0.0 ~ 100.0%)

F05.73 Curve 2 inflection point V/F SVC FVC PMVF PMSVC PMFVC 30.00%
RUN
(0x0549) 1 corresponding setting Set the corresponding percentage (0.00～100.00%)

F05.74 Curve 2 inflection point V/F SVC FVC PMVF PMSVC PMFVC 60.0%
RUN
(0x054A) 2 input voltage Set curve 2 inflection point 1 input voltage (0.0 ~ 100.0%)
F05.75 Curve 2 inflection point V/F SVC FVC PMVF PMSVC PMFVC 60.00%
RUN
(0x054B) 2 corresponding setting Set the corresponding percentage (0.00～100.00%)
F05.76 V/F SVC FVC PMVF PMSVC PMFVC 100.0%
Curve 2 upper limit RUN
(0x054C) Set the upper limit of curve 2 (0.00～100.0%)
F05.77 Curve 2 upper limit V/F SVC FVC PMVF PMSVC PMFVC 100.00%
RUN
(0x054D) corresponding setting Set the corresponding percentage (0.00 ~ 100.00%)
V/F SVC FVC PMVF PMSVC PMFVC
F05.80 AI terminal for digital 0：valid at low level 1：valid at high level 0000
RUN
(0x0550) input (0000 ~ 1111)
Unit：AI1 Tens：AI2
F05.81 Terminal characteristics V/F SVC FVC PMVF PMSVC PMFVC 0
STOP
(0x0551) selection See the function of the terminal for details. (0~63)
AI terminal function V/F SVC FVC PMVF PMSVC PMFVC
F05.82 70.00%
selection (as X The input setting is higher than the high level setting, which is the RUN
(0x0552) (0.00～100.00%)
terminal) input high level.
F05.83 V/F SVC FVC PMVF PMSVC PMFVC 30.00%
AI high level setting RUN
(0x0553) Less than the low level setting is low level. (0.00～100.00%)

4.9 F06：Output Terminal

26
RD11 Series Frequency converter Manual
Parameter Factory default Adjustable
Name Content
（Address） (range) properly

V/F SVC FVC PMVF PMSVC PMFVC

F06.00 0：0～10V 1：4.00～20.00mA 0
AO Output Mode RUN
(0x0600) (0 ~ 3)
2：0.00～20.00mA 3：FM frequency pulse output

V/F SVC FVC PMVF PMSVC PMFVC

0: given frequency 1: output frequency
2: Output current 3: Input voltage
4: Output voltage 5: Mechanical speed
6: given torque 7: output torque
F06.01 0
AO Output Selection 8: PID given amount 9: PID feedback amount RUN
(0x0601) (0 ~ 19)
10: Output power 11: Bus voltage
12: AI1 input value 13: AI2 input value
14: Reserved 15: PUL input value
16: Module temperature 1 17: Module temperature 2
18:485 communication given 19: virtual vY1 function

F06.02 V/F SVC FVC PMVF PMSVC PMFVC 100.0%

AO output gain RUN
(0x0602) Adjust the value of the analog output of the terminal. (0.0 ~ 200.0%)

F06.003 V/F SVC FVC PMVF PMSVC PMFVC 0.0%

AO output bias RUN
(0x0603) Set the A0 output offset to adjust the zero point of the terminal output. (-10.0～10.0%)
V/F SVC FVC PMVF PMSVC PMFVC
F06.04 0.01s
AO output filtering The size of the analog signal is filtered to eliminate interfering RUN
(0x0604) (0.0 ~ 6.00s)
signals.。

F06.1x: AO Extension
Parameter Factory default Adjustable
Name Content
（Address） (range) properly
V/F SVC FVC PMVF PMSVC PMFVC
F06.10 Extended AO output 0：0～10V 1：4.00～20.00mA 0
RUN
(0x060A) mode selection (0 ~ 3)
2：0.00～20.00mA 3:FM frequency pulse output
V/F SVC FVC PMVF PMSVC PMFVC
F06.11 Extended AO output 1
Corresponding to the extended AO output selection, the same as the RUN
(0x060B) selection (0 ~ 19)
F06.01 selection
F06.12 Extended AO output V/F SVC FVC PMVF PMSVC PMFVC 100.0%
RUN
(0x060C) gain Adjust the value of the analog output of the terminal. (0.0 ~ 200.0%)

F06.13 Extended AO output V/F SVC FVC PMVF PMSVC PMFVC 0.0%
RUN
(0x060D) offset Set the A0 output offset to adjust the zero point of the terminal output. (-10.0～10.0%)

F06.14 Extended AO output V/F SVC FVC PMVF PMSVC PMFVC 0.01s
RUN
(0x060E) filtering The size of the analog signal is filtered to eliminate interfering signals. (0.0 ~ 6.00s)

F06.2x-F06.3x： Digital, Relay Output

Parameter Factory default Adjustable
Name Content
（Address） (range) properly
V/F SVC FVC PMVF PMSVC PMFVC
F06.20 Output terminal polarity 0000
Unit digit: Y terminal Ten digit: Relay output terminal 1 RUN
(0x0614) selection (0000 ~ 1111)
0: positive polarity 1: negative polarity
F06.21 V/F SVC FVC PMVF PMSVC PMFVC 1
Output terminal Y RUN
(0x0615) See terminal Y function (0 ~ 63)
F06.22 Relay 1 output (TA-TB- V/F SVC FVC PMVF PMSVC PMFVC 4
RUN
(0x0616) TC) See terminal Y function (0 ~ 63)
F06.25 V/F SVC FVC PMVF PMSVC PMFVC 0.010s
Y output ON delay time RUN
(0x0619) Set the Y output ON delay time. (0.000～60.000s)
F06.26 Relay 1 output ON V/F SVC FVC PMVF PMSVC PMFVC 0.010s
RUN
(0x061A) delay time Set relay 1 output the ON delay time (0.000～60.000s)
F06.27 Extended Y output ON V/F SVC FVC PMVF PMSVC PMFVC 0.010s
RUN
(0x061B) delay time Set the extended Y output ON delay time. (0.000～60.000s)
F06.28 Extended relay 2ON V/F SVC FVC PMVF PMSVC PMFVC 0.010s
RUN
(0x061C) delay time Set the expansion relay 2 to output the ON delay time (0.000～60.000s)

27
RD11 Series Frequency converter Manual
F06.29 Y output OFF delay V/F SVC FVC PMVF PMSVC PMFVC 0.010s
RUN
(0x061D) time Set the Y output OFF delay time. (0.000～60.000s)
F06.30 Relay 1 output OFF V/F SVC FVC PMVF PMSVC PMFVC 0.010s
RUN
(0x061E) delay time Set relay 1 output OFF delay time. (0.000～60.000s)

F06.31 Extended Y1 output V/F SVC FVC PMVF PMSVC PMFVC 0.010s
RUN
(0x061F) OFF delay time Set the extended Y1 output OFF delay time (0.000～60.000s)

F06.32 Extended relay 2 V/F SVC FVC PMVF PMSVC PMFVC 0.010s
RUN
(0x0620) output OFF delay time Set the extended relay 2 output OFF delay time. (0.000～60.000s)

F06.4x: Frequency Detection

Parameter Factory default Adjustable

Name Content
（Address） (range) properly
2.00Hz
F06.40 Frequency detection V/F SVC FVC PMVF PMSVC PMFVC
(0.00～max RUN
(0x0628) value 1 Set the frequency detection value 1
frequency)
1.00Hz
F06.41 Frequency detection V/F SVC FVC PMVF PMSVC PMFVC
(0.00～max RUN
(0x0629) amplitude 1 Set the frequency detection amplitude 1
frequency)
2.00Hz
F06.42 Frequency detection V/F SVC FVC PMVF PMSVC PMFVC
(0.00～max RUN
(0x062A) value 2 Set the frequency detection value 2
frequency)
1.00Hz
F06.43 Frequency detection V/F SVC FVC PMVF PMSVC PMFVC
(0.00～max RUN
(0x062B) range 2 Set the frequency detection range 2
frequency)
The given frequency 2.00Hz
F06.44 V/F SVC FVC PMVF PMSVC PMFVC
reaches the detection (0.00～max RUN
(0x062C) Set the given frequency to reach the detection range
range frequency)

F06.5x：Monitor parameter comparator output

Parameter Factory default Adjustable

Name Content
（Address） (range) properly

V/F SVC FVC PMVF PMSVC PMFVC

F06.50 Comparator 1 monitor Units and Tens digits: Set yy value of the Cxx.yy 00～63 0001
RUN
(0x0632) selection (0000 ~ 0763)
Hundreds and thousands: Set xx value of the Cxx.yy 00～07

F06.51 Comparator 1 upper V/F SVC FVC PMVF PMSVC PMFVC 3000
RUN
(0x0633) limit Set the upper limit of comparator 1 (0 ~ 65535)
F06.52 Comparator 1 lower V/F SVC FVC PMVF PMSVC PMFVC 0
RUN
(0x0634) limit Set the lower limit of comparator 1 (0 ~ 65535)
F06.53 V/F SVC FVC PMVF PMSVC PMFVC 0
Comparator 1 bias RUN
(0x0635) Set the comparator 1 offset value (0 ~ 1000)
V/F SVC FVC PMVF PMSVC PMFVC
F06.54 Action selection when 0：Continue running(digital terminal output only); 0
RUN
(0x0636) sending CP1 1：Warning and free stop;2：Warning and continue running; (0 ~ 3)
3：Forced stop
V/F SVC FVC PMVF PMSVC PMFVC
F06.55 Comparator 2 monitor Units and Tens digits: Set yy value of the Cxx.yy 00～63 0002
RUN
(0x0637) selection (0000 ~ 0763)
Hundreds and thousands: Set xx value of the Cxx.yy 00～07
F06.56 Comparator 2 upper V/F SVC FVC PMVF PMSVC PMFVC 30
RUN
(0x0638) limit Set the upper limit of comparator 2 (0 ~ 65535)
F06.57 Comparator 2 lower V/F SVC FVC PMVF PMSVC PMFVC 0
RUN
(0x0639) limit Set the lower limit of comparator 2 (0 ~ 65535)
F06.58 V/F SVC FVC PMVF PMSVC PMFVC 0
Comparator 2 bias RUN
(0x063A) Set the comparator 2 offset value (0 ~ 1000)
V/F SVC FVC PMVF PMSVC PMFVC
F06.59 Action selection when 0: Continue running (digital terminal output only) 0
RUN
(0x063B) sending CP2 1: Warning and free stop 2: Warning and continue to run 3: Forced (0 ~ 3)
stop

28
RD11 Series Frequency converter Manual
F06.6x：Virtual Input and Output Terminal
Parameter Factory default Adjustable
Name Content
（Address） (range) properly

F06.60 Virtual vX1 terminal V/F SVC FVC PMVF PMSVC PMFVC 0
RUN
(0x063C) function selection See terminal X function (0 ~ 63)
F06.61
Virtual vX2 terminal V/F SVC FVC PMVF PMSVC PMFVC 0
(0x063D) RUN
function selection See terminal X function (0 ~ 63)
RUN
F06.62 Virtual vX3 terminal V/F SVC FVC PMVF PMSVC PMFVC 0
RUN
(0x063E) function selection See terminal X function (0 ~ 63)
F06.63 Virtual vX4 terminal V/F SVC FVC PMVF PMSVC PMFVC 0
RUN
(0x063F) function selection See terminal X function (0 ~ 63)
V/F SVC FVC PMVF PMSVC PMFVC
0: Internal connection with virtual vYn 1: Link with physical terminal
F06.64 vX terminal valid status Xn 0000
RUN
(0x0640) source 2:whether the function code setting is valid? (0000 ~ 2222)
Unit: Virtual vX1 Ten: Virtual vX2
Hundreds place: virtual vX3 thousand: virtual vX4
V/F SVC FVC PMVF PMSVC PMFVC
Virtual vX terminal
F06.65 0: invalid; 1: valid 0000
function code setting RUN
(0x0641) Unit: Virtual vX1 Ten: Virtual vX2 (0000 ~ 1111)
valid status
Hundreds place: virtual vX3 thousand: virtual vX4
F06.66 Virtual vY1 output V/F SVC FVC PMVF PMSVC PMFVC 0
RUN
(0x0642) selection See Y terminal function for details. (0～31)
F06.67 Virtual vY2 output V/F SVC FVC PMVF PMSVC PMFVC 0
RUN
(0x0643) selection See Y terminal function for details. (0～31)

F06.68 Virtual vY3 output V/F SVC FVC PMVF PMSVC PMFVC 0
RUN
(0x0644) selection See Y terminal function for details. (0～31)

F06.69 Virtual vY4 output V/F SVC FVC PMVF PMSVC PMFVC 0
RUN
(0x0645) selection See Y terminal function for details. (0～31)
F06.70 vY1 output ON delay V/F SVC FVC PMVF PMSVC PMFVC 0.010s
RUN
(0x0646) time Set vY1 output ON delay time (0.000～60.000s)
F06.71 vY2 output ON delay V/F SVC FVC PMVF PMSVC PMFVC 0.010s
RUN
(0x0647) time Set vY2 output ON delay time (0.000～60.000s)
F06.72 vY3 output ON delay V/F SVC FVC PMVF PMSVC PMFVC 0.010s
RUN
(0x0648) time Set vY3 output ON delay time (0.000～60.000s)
F06.73 vY4 output ON delay V/F SVC FVC PMVF PMSVC PMFVC 0.010s
RUN
(0x0649) time Set vY4 output ON delay time (0.000～60.000s)
F06.74 vY1 output OFF delay V/F SVC FVC PMVF PMSVC PMFVC 0.010s
RUN
(0x064A) time Set vY1 output OFF delay time (0.000～60.000s)
F06.75 vY2 output OFF delay V/F SVC FVC PMVF PMSVC PMFVC 0.010s
RUN
(0x064B) time Set vY2 output OFF delay time (0.000～60.000s)
F06.76 vY3 output OFF delay V/F SVC FVC PMVF PMSVC PMFVC 0.010s
RUN
(0x064C) time Set vY3 output OFF delay time (0.000～60.000s)
F06.77 vY4 output OFF delay V/F SVC FVC PMVF PMSVC PMFVC 0.010s
RUN
(0x064D) time Set vY4 output OFF delay time (0.000～60.000s)

29
RD11 Series Frequency converter Manual

4.10 F07 ：Operational Control

Parameter Factory default Adjustable
Name Content
（Address） (range) properly
V/F SVC FVC PMVF PMSVC PMFVC
F07.00 0: started by the start frequency 0
Start mode STOP
(0x0700) 1: DC braking first starts again from the starting frequency (0 ~ 2)
2: Start after the speed tracking and direction judgment
F07.01 Start pre-excitation V/F SVC FVC PMVF PMSVC PMFV 0.00s
Only asynchronous machine vector control (without PG) supports STOP
(0x0701) time (0.00～60.00s)
pre-excitation, other ignore
V/F SVC FVC PMVF PMSVC PMFVC 0.50Hz
F07.02
Starting frequency When the given frequency is less than this value, it does not start and (0.00～upper limit STOP
(0x0702)
is in standby state frequency setting)
V/F SVC FVC PMVF PMSVC PMFVC
0: off 1: on
Unit: terminal start protection when exiting abnormal
Tens: Jog terminal start protection when exiting abnormal
F07.03 Start protection 0111
Hundreds: terminal start protection when the command channel is STOP
(0x0703) selection (0000～1111)
switched to the terminal
Note: When the free stop, emergency stop, and forced stop
commands are valid, the terminal start protection is enabled by
default, and the protection time is reported as A.RUNx warning.
V/F SVC FVC PMVF PMSVC PMFVC
Unit: running direction
0：Direction unchanged 1：Direction reversed
F07.05 Tens：running direction selection 0000
Direction of rotation 0：allow Fwd and Rev commands 1：Fwd command only STOP
(0x0705) (0000～1121)
2：Rev command only
Hundreds：Frequency control command
0：command is invalid 1：command is valid
F07.06 Power failure restart V/F SVC FVC PMVF PMSVC PMFVC 0
STOP
(0x0706) action selection 0：Invalid 1：Valid (0 ~ 1)
F07.07 Power failure restart V/F SVC FVC PMVF PMSVC PMFVC 0.50s
STOP
(0x0707) waiting time Set the power failure restart waiting time (0.00～60.00s)

F07.1x：Stop Control
Parameter Factory default Adjustable
Name Content
（Address） (range) properly
F07.10 V/F SVC FVC PMVF PMSVC PMFVC 0
Stop mode RUN
(0x070A) 0: Deceleration stop 1: Free stop (0 ~ 1)
V/F SVC FVC PMVF PMSVC PMFVC 0.50Hz
F07.11 Shutdown detection
When decelerating to stop, when the inverter output frequency is less (0.00～upper limit RUN
(0x070B) frequency
than this value, it will enter the stop state. frequency setting)
F07.12 Stop and restart limit V/F SVC FVC PMVF PMSVC PMFVC 0.00s
STOP
(0x070C) time Waiting time after restarting after shutdown (0.00～60.00s)
V/F SVC FVC PMVF PMSVC PMFVC
Insufficient lower limit
F07.15 0 : Run according to frequency command 0
frequency action RUN
(0x070F) 1 : Free running stops, enters the pause state (0～3)
selection
2 : Run at the following limited frequency 3 : Zero speed operation
V/F SVC FVC PMVF PMSVC PMFVC
F07.16 Zero speed torque 60.0%
Set zero speed torque current, 100.0% corresponds to inverter rated RUN
(0x0710) retention factor (0.0～150.0%)
current
F07.17 Zero speed torque V/F SVC FVC PMVF PMSVC PMFVC 0.0s
RUN
(0x0711) holding time Set zero speed torque hold time (0.0～6000.0s)
F07.18 Positive reversal dead V/F SVC FVC PMVF PMSVC PMFVC 0.0s
STOP
(0x0712) time Fwd and Rev switching, zero frequency maintenance time (0.0～120.0s)

F07.2x：DC Breaking and Speed Tracking

Parameter Factory default Adjustable
Name Content
（Address） (range) properly

30
RD11 Series Frequency converter Manual
F07.20 Braking current before V/F SVC FVC PMVF PMSVC PMFVC 60.0%
STOP
(0x0714) starting Set the brake current before starting (0.0～150.0%)
F07.21 Braking time before V/F SVC FVC PMVF PMSVC PMFVC 0.0s
STOP
(0x0715) starting Set the brake time before starting (0.0～60.0s)
F07.22 DC braking start V/F SVC FVC PMVF PMSVC PMFVC 1.00Hz
STOP
(0x0716) frequency Set the DC brake start frequency (0.00～50.00Hz)
V/F SVC FVC PMVF PMSVC PMFVC
F07.23 60.0%
DC braking current Refer to rated current，because the internal limit current cannot STOP
(0x0717) (0.0～150.0%)
exceed the rated current
F07.24 DC braking time during V/F SVC FVC PMVF PMSVC PMFVC 0.0s
STOP
(0x0718) stopping Set the DC braking time during stopping (0.0～60.0s)
V/F SVC FVC PMVF PMSVC PMFVC
Units: Search method
0: Search from the maximum frequency 1: Search from the stop
F07.25 frequency 0000
Speed tracking mode Tens：Reverse search STOP
(0x0719) (0000～1111)
0：Off 1：On
Hundreds: Search source
0：Software search 1：Hardware search
F07.26 V/F SVC FVC PMVF PMSVC PMFVC 0.5s
Speed tracking speed STOP
(0x071A) Set the speed of tracking speed (0.0～60.0s)
F07.27 Speed tracking stop V/F SVC FVC PMVF PMSVC PMFVC 1.00s
STOP
(0x071B) delay Set speed tracking stop delay (0.0～60.0s)

F07.28 V/F SVC FVC PMVF PMSVC PMFVC 120.0%

Speed tracking current STOP
(0x071C) Set speed tracking current (0.0～400.0%)

F07.3x：Jog
Parameter Factory default Adjustable
Name Content
（Address） (range) properly
5.00Hz
F07.30 Jog running frequency V/F SVC FVC PMVF PMSVC PMFVC
(0.00～Max RUN
(0x071E) setting Set jog running frequency
frequency)
F07.31 V/F SVC FVC PMVF PMSVC PMFVC 10.0s
Jog acceleration time RUN
(0x071F) Set jog acceleration time (0.0～650.0s)
F07.32 V/F SVC FVC PMVF PMSVC PMFVC 10.0s
Jog deceleration time RUN
(0x0720) Set jog deceleration time (0.0～650.0s)
F07.33 V/F SVC FVC PMVF PMSVC PMFVC 0
Jog S curve selection RUN
(0x0721) 0：Invalid 1：Valid (0～1)
V/F SVC FVC PMVF PMSVC PMFVC
F07.34 Jog stop mode 0
Set stop mode STOP
(0x0722) selection (0～1)
0: According to F7.10 setting mode 1: Deceleration only

F07.4x：Startup、Stopping Frequency Maintenance and Jump Frequency

Parameter Factory default Adjustable
Name Content
（Address） (range) properly
V/F SVC FVC PMVF PMSVC PMFVC 0.50Hz
F07.40 Maintain frequency at
Startup maintenance frequency is greater than the start frequency, (0.00～Upper limit STOP
(0x0728) startup
less than the upper limit set frequency frequency)
V/F SVC FVC PMVF PMSVC PMFVC
F07.41 Maintain frequency 0.0s
The value should be higher than the start frequency, and when it is STOP
(0x0729) time at startup (0.0～60.0s)
lower, according to start frequency
0.50Hz
F07.42 Maintain frequency V/F SVC FVC PMVF PMSVC PMFVC
(0.00～Upper limit STOP
(0x072A) during stop Set the maintain frequency during stop
frequency)
F07.43 Maintain frequency V/F SVC FVC PMVF PMSVC PMFVC 0.0s
STOP
(0x072B) time during stop Set the time of stop maintain frequency (0.0～60.0s)
0.00Hz
F07.44 V/F SVC FVC PMVF PMSVC PMFVC
Jump frequency 1 (0.00～Max RUN
(0x072C) Set the jump frequency 1
frequency)
F07.45 Jump frequency 1 V/F SVC FVC PMVF PMSVC PMFVC 0.00Hz RUN

31
RD11 Series Frequency converter Manual
(0x072D) amplitude Set the amplitude of jump frequency 1 (0.00～Max
frequency)
0.00Hz
F07.46 V/F SVC FVC PMVF PMSVC PMFVC
Jump frequency 2 (0.00～Max RUN
(0x072E) Set the jump frequency 2
frequency)
0.00Hz
F07.47 Jump frequency 2 V/F SVC FVC PMVF PMSVC PMFVC
(0.00～Max RUN
(0x072F) amplitude Set the amplitude of jump frequency 2
frequency)

4.11 F08：Auxiliary Control

Parameter Factory default Adjustable
Name Content
（Address） (range) properly
F08.00 V/F SVC FVC PMVF PMSVC PMFVC 0
Counter input source RUN
(0x0800) 0：normal X terminal 1：input PUL terminal 2~5：reserved (0 ~ 5)
F08.01 Count input frequency V/F SVC FVC PMVF PMSVC PMFVC 0
RUN
(0x0801) division Set the input frequency division of the counter (0 ~ 6000)
F08.02 V/F SVC FVC PMVF PMSVC PMFVC 1000
Counter maximum RUN
(0x0802) Set the max value of the counter (0 ~ 65000)
F08.03 V/F SVC FVC PMVF PMSVC PMFVC 500
Counter setting RUN
(0x0803) Counter setting (0 ~ 65000)
F08.04 Pulse number per V/F SVC FVC PMVF PMSVC PMFVC 10.0
RUN
(0x0804) meter Set the counter value for per meter (0.1～6500.0)
F08.05 V/F SVC FVC PMVF PMSVC PMFVC 1000
Set length STOP
(0x0805) Set length (0 ~ 65000M)
F08.06 V/F SVC FVC PMVF PMSVC PMFVC 0
Actual length STOP
(0x0806) Set the actual length (0 ~ 65000M)
V/F SVC FVC PMVF PMSVC PMFVC
F08.07 0
Timer time unit Unit of the timer STOP
(0x0807) (0 ~ 2)
0：Second 1：Minute 2：Hour
F08.08 V/F SVC FVC PMVF PMSVC PMFVC 0
Timer setting STOP
(0x0808) Set the timer setting (0 ~ 65000)

F08.3x：Swing Frequency Control

Parameter Factory default Adjustable
Name Content
（Address） (range) properly
V/F SVC FVC PMVF PMSVC PMFVC
F08.30 Swing frequency 0
0：Swing frequency control is invalid 1：Swing frequency control is STOP
(0x081E) control (0 ~ 1)
valid

V/F SVC FVC PMVF PMSVC PMFVC

Unit：Start Mode
0：Automatically 1：Terminal manual
F08.31 Swing frequency 0000
Tens：Swing amplitude control STOP
(0x081F) amplitude control (0000～0111)
0: Relative center frequency 1:Relative maximum frequency.
Hundreds: preset frequency enable
0: not enabled 1: enabled

0.00Hz
yF08.32 Swing frequency V/F SVC FVC PMVF PMSVC PMFVC
(0~upper limit STOP
(0x0820) preset frequency Set the swing frequency preset frequency
frequency)
Swing frequency
F08.33 V/F SVC FVC PMVF PMSVC PMFVC 0.0s
preset frequency STOP
(0x0821) Set the swing frequency preset frequency waiting time (0.0～3600.0s)
waiting time
F08.34 Swing frequency V/F SVC FVC PMVF PMSVC PMFVC 10.0%
STOP
(0x0822) amplitude Set the swing frequency amplitude (0.0～50.0%)
F08.35 V/F SVC FVC PMVF PMSVC PMFVC 10.0%
Kick frequency STOP
(0x0823) Set the kick frequency (0.0～50.0%)
F08.36 V/F SVC FVC PMVF PMSVC PMFVC 5.00s
Triangle wave rise time STOP
(0x0824) Set the triangle wave rise time (0.1～999.9s)

F08.37 V/F SVC FVC PMVF PMSVC PMFVC 5.00s

Triangle wave fall time STOP
(0x0825) Set the triangle wave fall time (0.0~100.0s)

32
RD11 Series Frequency converter Manual

4.12 F09：Reserved

4.13 F10：Protection Parameter

Parameter Factory default Adjustable
Name Content
（Address） (range) properly
V/F SVC FVC PMVF PMSVC PMFVC
Automatically limit the output current cannot exceed the overcurrent
F10.00 Overcurrent 0
suppression point to prevent overcurrent faults RUN
(0x0A00) suppression (0 ~ 1)
0: Suppression is always valid 1: Acceleration/deceleration is valid,
constant speed is invalid
V/F SVC FVC PMVF PMSVC PMFVC
F10.01 Overcurrent 160.0%
Set the load current limit level, the value 100% corresponds to the RUN
(0x0A01) suppression point (0.0 ～ 300.0%)
rated motor current.。
F10.02 Overcurrent V/F SVC FVC PMVF PMSVC PMFVC 100.0%
RUN
(0x0A02) suppression gain Set the response effect of overcurrent suppression. (0.0 ～ 500.0%)
V/F SVC FVC PMVF PMSVC PMFVC
Set whether current-related protection is enabled
Unit: Wave-by-wave current limit (CBC)
0: off 1: on
F10.03 Current protection Tens: OC protection interference suppression 0001
STOP
(0x0A03) setting 1 0: Normal 1: Primary interference suppression 2: Secondary (0000~0221)
interference suppression
Hundreds: SC protection interference suppression
0: Normal 1: Primary interference suppression 2: Secondary
interference suppression
V/F SVC FVC PMVF PMSVC PMFVC
F10.04 Current protection 0001
Unit position: three-phase current and protection options STOP
(0x0A04) setting 2 (0000~0001)
0: off 1: On

F10.1x：Voltage Protection
Parameter Factory default Adjustable
Name Content
（Address） (range) properly
V/F SVC FVC PMVF PMSVC PMFVC
F10.10 Bus overvoltage Set whether the bus overvoltage hardware protection function is 0
STOP
(0x0A0A) hardware protection enabled. (0 ~ 1)
0: off 1: on
V/F SVC FVC PMVF PMSVC PMFVC
When the bus voltage is greater than the overvoltage suppression
point, it will slow down or stop the acceleration and deceleration to
prevent overvoltage faults.
F10.11 Bus overvoltage 0012
Unit: Overvoltage suppression function STOP
(0x0A0B) suppression (0000 ~0012)
0: Off 1: Only enable during deceleration 2: Enable during both
acceleration and deceleration
Tens: overexcitation function
0: off 1: on
T3：780
S2：365
F10.12 Bus overvoltage V/F SVC FVC PMVF PMSVC PMFVC (0~ overvoltage point)
T3 overvoltage STOP
(0x0A0C) suppression point Set bus voltage value for trigger overvoltage suppression function
point:820V;S2
overvoltage
point:390V
F10.13 Bus overvoltage V/F SVC FVC PMVF PMSVC PMFVC 100.0%
RUN
(0x0A0D) suppression gain Set the response effect of overvoltage suppression (0.0～500.0%)
V/F SVC FVC PMVF PMSVC PMFVC
F10.14 Set whether the energy brake function is on 2
Energy brake enable RUN
(0x0A0E) 0: Off 1: On, but off overvoltage suppression (0 ~2)
2: Turn on, and turn on the overvoltage suppression function.

33
RD11 Series Frequency converter Manual
T3：735
S2：360
V/F SVC FVC PMVF PMSVC PMFVC
F10.15 Energy consuming Set the energy consuming braking action voltage, when the bus (0~ overvoltage point)
T3 overvoltage RUN
(0x0A0F) braking action voltage voltage is greater than this value, the energy consuming brake starts
to act point:820V;S2
overvoltage
point:390V

V/F SVC FVC PMVF PMSVC PMFVC

When the bus voltage is lower than the undervoltage suppression
F10.16 Bus undervoltage 0
point, the operating frequency is automatically adjusted to suppress STOP
(0x0A10) suppression (0 ~ 1)
the bus voltage from decreasing, preventing the undervoltage fault.
0: off 1: on

T3：430
S2：240
F10.17 Bus undervoltage V/F SVC FVC PMVF PMSVC PMFVC (0~ overvoltage point)
T3 overvoltage STOP
(0x0A11) suppression point Set bus voltage value for trigger undervoltage suppression function
point:820V;S2
overvoltage
point:390V
F10.18 Bus undervoltage V/F SVC FVC PMVF PMSVC PMFVC 100.0%
RUN
(0x0A12) suppression gain Set the response effect of undervoltage suppression (0.0～500.0%)
T3：350
S2：190
V/F SVC FVC PMVF PMSVC PMFVC (0~ overvoltage point)
F10.19 Bus undervoltage
Set the allowable lower limit of the bus voltage. Below this value, the T3 overvoltage STOP
(0x0A13) protection point
inverter reports undervoltage fault. point:820V;S2
overvoltage
point:390V

F10.2x：Auxiliary Protection

Parameter Factory default Adjustable

Name Content
（Address） (range) properly
V/F SVC FVC PMVF PMSVC PMFVC
Set whether the input and output phase loss protection functions are
enabled.
Unit: Output phase loss protection
F10.20 Input and output phase 0021
0: off 1: on STOP
(0x0A14) loss protection options (000 ~ 0121)
Tens: input phase loss protection
0: off 1: On, when detect the input loss phase report warning
A.ILF, continue to run
2: On, when detect input loss phase report fault E.ILF, free stop
V/F SVC FVC PMVF PMSVC PMFVC
F10.21 Input phase loss 10%
Set the percentage of voltage detection of the input phase loss STOP
(0x0A15) threshold (0 ~30.0%)
detection function, 100% corresponds to the rated bus voltage
V/F SVC FVC PMVF PMSVC PMFVC
Set whether the inverter output and the inverter cooling fan ground
short circuit protection function are enabled.
F10.22 Ground short circuit 0011
Unit: Output short circuit protection STOP
(0x0A16) protection option (0000 ~0012)
0: off 1: on
Tens: fan to ground short circuit protection
0: off 1: on
V/F SVC FVC PMVF PMSVC PMFVC
Set the inverter cooling fan operation mode
0: The fan runs after the inverter is powered on.
F10.23 Fan ON/OFF control 1
1: After the shutdown, the fan operation is related to temperature, and RUN
(0x0A17) selection (0～2)
the operation is running.
2: After the shutdown, the fan stops after F10.24, and the operation
is related to temperature.
F10.24 V/F SVC FVC PMVF PMSVC PMFVC 30.00s
Fan control delay time STOP
(0x0A18) Set the time from shutdown to the cooling fan stops running (0 ~600.00)
Inverter overheating V/F SVC FVC PMVF PMSVC PMFVC
F10.25 80.0℃
oH1 warning detection Set the temperature value of the inverter overheat warning, which is RUN
(0x0A19) (0 ~100.0)
level highter than the value to report the overheat warning.

34
RD11 Series Frequency converter Manual
F10.3x：Load Protection
Parameter Factory default Adjustable
Name Content
（Address） (range) properly
Motor overload V/F SVC FVC PMVF PMSVC PMFVC
F10.30 100.0%
protection curve Set the coefficient of overload protection for the load motor. STOP
(0x0A1E) (0 ~250.0%)
coefficient Increasing this value can increase the overload capacity of the motor.
Selection of inverter V/F SVC FVC PMVF PMSVC PMFVC
F10.31 overload 0
Set whether the overload protection function is valid when the speed STOP
(0x0A1F) characteristics at low (0 ~1)
is low (less than 5Hz)
speed
V/F SVC FVC PMVF PMSVC PMFVC
Set the inverter load warning detection mode and the early warning
mode at this time
Unit: Load warning checkout 1 setting
0: No detection 1: The detection load is too large
2: Excessive load detection only at constant speed 3: Insufficient
detection load
4: Insufficient load detection only at constant speed
F10.32 Load warning checkout 0000
Ten digits: warning setting when load warning is detected 1 STOP
(0x0A20) setting (0000 ~1414)
0: continue to run, report A.LD1 1: Free stop, report to E.LD1
Hundreds place: load warning checkout 2 setting
0: No detection 1: The detection load is too large
2: Excessive load detection only at constant speed 3: Insufficient
detection load
4: Insufficient load detection only at constant speed
Thousands: warning setting when load warning is detected 2
0: continue to run, report A.LD1 1: Free stop, report to E.LD1
V/F SVC FVC PMVF PMSVC PMFVC
Set the detection value of load warning 1
F10.33 Load warning detection Under VF control, this value 100% is corresponding to the rated 130.0%
STOP
(0x0A21) level 1 current of the motor. (0 ~200.0%)
Under vector control, this value 100% is corresponding to the rated
output torque of the motor.
V/F SVC FVC PMVF PMSVC PMFVC
F10.34 Load warning detection Set the duration of the detected load warning 1 and the load is greater 5.0s
STOP
(0x0A22) time 1 than the load warning detection level for the duration, and the load (0 ~60.0)
warning 1 is reported.
V/F SVC FVC PMVF PMSVC PMFVC
Set the detection value of load warning 1
F10.35 Load warning detection Under VF control, this value 100% is corresponding to the rated 130.0%
STOP
(0x0A23) level 2 current of the motor. (0 ~200.0%)
Under vector control, this value 100% is corresponding to the rated
output torque of the motor.
V/F SVC FVC PMVF PMSVC PMFVC
F10.36 Load warning detection Set the duration of the detected load warning 2 and the load is greater 5.0s
STOP
(0x0A24) time 2 than the load warning detection level for the duration, and the load (0 ~60.0)
warning 2 is reported.

F10.4x：Stall Protection
Parameter Factory default Adjustable
Name Content
（Address） (range) properly
V/F SVC FVC PMVF PMSVC PMFVC
Set the warning detection mode selection and alarm mode selection
when deviation between the motor given speed and feedback speed
Speed deviation is excessive
F10.40 0000
excessive protection Unit: Check out the selection STOP
(0x0A28) (0000 ~0012)
action 0: No detection 1: Only at constant speed detection 2: Always
detected
Ten places: alarm selection
0: Free stop and report fault 1: Alarm and continue to run
Speed deviation V/F SVC FVC PMVF PMSVC PMFVC
F10.41 10.0%
excessive detection Set the detected value when speed deviation is excessive. This value STOP
(0x0A29) (0 ~60.0%)
threshold corresponds to F01.10 [maximum frequency].

35
RD11 Series Frequency converter Manual
V/F SVC FVC PMVF PMSVC PMFVC
Speed deviation
F10.42 Set the detection time of the excessive speed deviation, when the 2s
excessive detection STOP
(0x0A2A) speed deviation is excessive and the duration is longer than this time (0 ~60)
time
value the deviation warning reported
V/F SVC FVC PMVF PMSVC PMFVC
Set the alarm detection mode selection and alarm mode selection
when the motor is overspeed
F10.43 Speed protection Unit: Check out the selection 0002
STOP
(0x0A2B) action 0: No detection 1: Only at constant speed detection 2: Always (0000 ~0012)
detected
Ten places: alarm selection
0: Free stop and report fault 1: Alarm and continue to run
V/F SVC FVC PMVF PMSVC PMFVC
F10.44 Speed exceed 110.0%
Set the speed exceed warning detection value, which corresponds STOP
(0x0A2C) detection threshold (0 ~150.0%)
to F01.10 [maximum frequency]
V/F SVC FVC PMVF PMSVC PMFVC
F10.45 Speed exceed Set the duration of the detection of the flying speed, the feedback 0.010s
STOP
(0x0A2D) detection time speed is greater than F10.44 and continue for that time, and the (0 ~2.000)
speed warning is detected.

F10.5x：Fault Recovery Protection

Parameter Factory default Adjustable
Name Content
（Address） (range) properly
V/F SVC FVC PMVF PMSVC PMFVC
F10.50 Set the allowable times of fault self-recovery. 0
Fault self-recovery STOP
(0x0A32) Note: the value of 0 indicate the function is turn off otherwise the (0 ~10)
function is enable
F10.51 Fault self-recovery V/F SVC FVC PMVF PMSVC PMFVC 1.0s
STOP
(0x0A33) interval Set the waiting time from fault to reset (0 ~100.0)
V/F SVC FVC PMVF PMSVC PMFVC
F10.52 Number of fault
This value indicates the number of self-recovery that have been 0 READ
(0x0A34) recovered
performed. This parameter is a read-only parameter.

4.14 F11：Operator Parameter

F11.0x：Button Operation
Parameter Factory default Adjustable
Name Content
（Address） (range) properly
V/F SVC FVC PMVF PMSVC PMFVC
F11.00 0: No lock 1: Keyboard function parameter modification lock 0
Key lock selection RUN
(0x0B00) 2: Function parameters and non-start and stop button lock 3: function (0 ~ 3)
parameters and button full lock
F11.01 V/F SVC FVC PMVF PMSVC PMFVC 0
Key lock password RUN
(0x0B01) Set the key lock password (0 ~ 65535)
V/F SVC FVC PMVF PMSVC PMFVC
0: Invalid 1: Reverse run key
2: Forward jog run key 3: Reverse jog run key
4: Keyboard command channel and terminal naming channel switch
F11.02 Keyboard multi- 5: Keyboard command channel and communication naming channel 0
STOP
(0x0B02) function key selection switch (0 ~ 7)
6: Terminal command channel and communication naming channel
switch
7: keyboard, terminal, communication command channel cycle
switching
V/F SVC FVC PMVF PMSVC PMFVC
F11.03 Keyboard STOP 0: Non-keyboard control mode is invalid 0
STOP
(0x0B03) button settings 1: Non-keyboard control mode stops according to stop mode (0 ~ 2)
2: Non-keyboard control mode stops in free mode
V/F SVC FVC PMVF PMSVC PMFVC
Unit keyboard up and down keys to modify the selection
Status interface up and
F11.04 0: Invalid 1: Used to adjust the frequency keyboard given F01.09 0011
down keys (knob) STOP
(0x0B04) 2: used to adjust the PID keyboard given F13.01 (0000~0213)
function selection
3: Keyboard up and down keys to modify the parameter number
setting

36
RD11 Series Frequency converter Manual
Ten place: power down storage
0: frequency power down is not stored 1: frequency power down
storage
Hundreds: Action Limit
0: Run stop adjustable 1: Only adjustable during operation, stop and
keep
2: Adjustable during operation, stop and clear
V/F SVC FVC PMVF PMSVC PMFVC
Up and down keys to
F11.05 Ten digits: yy setting in function parameter number Fxx.yy 00～99 0109
quickly change the RUN
(0x0B05) Hundreds of thousands: xx setting in function parameter number (0000 ~ 1563)
parameter code setting
Fxx.yy 00~15

V/F SVC FVC PMVF PMSVC PMFVC

Units: Built-in, external keyboard button commands
(run command, stop/reset command)
F11.06 Keyboard command 0: External priority, when the external is valid, the built-in is invalid. 0000
STOP
(0x0B06) key selection 1: Built-in priority, when the built-in is valid, the external is invalid (0000 ~ 1122)
2: Both internal and external are valid, the stop/reset command takes
precedence; when the forward and reverse are valid at the same
time, it is used as the stop command.

F11.1x：Status Interface Cyclic Monitoring

Parameter Factory default Adjustable

Name Content
（Address） (range) properly
V/F SVC FVC PMVF PMSVC PMFVC
Unit: left shift key to adjust the first line of monitoring
Status interface left 0: Invalid 1: Valid
F11.10 0011
shift, right shift key Tens: right shift key to adjust the second line of monitoring STOP
(0x0B0A) (0000 ~ 0011)
function selection 0: Invalid 1: Valid
When the left/right shift key is invalid, the monitor display value is
displayed as parameter 1 after power-on.
V/F SVC FVC PMVF PMSVC PMFVC
The first line of the Ten digits: yy setting in monitoring parameter number Cxx.yy
F11.11 00～63 0000
keyboard shows the RUN
(0x0B0B) (0000 ~ 0763)
parameter 1 Hundreds of thousands: monitoring parameter number Cxx.yy xx
setting 00～07
The first line of the
F11.12 V/F SVC FVC PMVF PMSVC PMFVC 0001
keyboard shows the RUN
(0x0B0C) Ditto (0000 ~ 0763)
parameter 2
The first line of the
F11.13 V/F SVC FVC PMVF PMSVC PMFVC 0002
keyboard shows the RUN
(0x0B0D) Ditto (0000 ~ 0763)
parameter 3
The first line of the
F11.14 V/F SVC FVC PMVF PMSVC PMFVC 0011
keyboard shows the RUN
(0x0B0E) Ditto (0000 ~ 0763)
parameter 4
The second line of the
F11.15 V/F SVC FVC PMVF PMSVC PMFVC 0002
keyboard shows the RUN
(0x0B0F) Ditto (0000 ~ 0763)
parameter 1
The second line of the
F11.16 V/F SVC FVC PMVF PMSVC PMFVC 0004
keyboard shows the RUN
(0x0B10) Ditto (0000 ~ 0763)
parameter 2

The second line of the

F11.17 V/F SVC FVC PMVF PMSVC PMFVC 0010
keyboard shows the RUN
(0x0B11) Ditto (0000 ~ 0763)
parameter 3
The second line of the
F11.18 V/F SVC FVC PMVF PMSVC PMFVC 0012
keyboard shows the RUN
(0x0B12) Ditto (0000 ~ 0763)
parameter 4

37
RD11 Series Frequency converter Manual
F11.2x：Monitoring Parameter
Parameter Factory default Adjustable
Name Content
（Address） (range) properly
V/F SVC FVC PMVF PMSVC PMFVC
Unit digit: Output frequency display selection
0: Target frequency 1: Operating frequency >=2: Target frequency,
F11.20 Keyboard display item the filtering depth increases with this value 0002
RUN
(0x0B14) settings Ten: reserved (0000 ~ 111F)
Hundreds: Power Display Dimensions
0: Power display percentage (%) 1: Power display kilowatt (KW)
Thousands: reserved

F11.21 V/F SVC FVC PMVF PMSVC PMFVC 100.0%

Speed display factor RUN
(0x0B15) Adjust the speed display of C00.06. (0.0～500.0%)

F11.22 V/F SVC FVC PMVF PMSVC PMFVC 100.0%

Power display factor RUN
(0x0B16) Adjust the output power display of C00.10. (0.0～500.0%)
V/F SVC FVC PMVF PMSVC PMFVC
Unit: Reserved
Ten: C05 display selection
0: Automatically switch according to the control mode
1:VF mode related parameters
2: VC mode related parameters
F11.23 Monitoring parameter Hundreds place: C00.40~C00.63 display selection 0000
RUN
(0x0B17) group display selection 0: Do not display 1: display (0000 ~ FFFF)
Thousands: Communication fault code switching enable
0: not enabled
1: Enable, the fault code is switched to the same as AC300 when 485
communication
2: Enable, the fault code is switched to the AC70 when 485
communication
V/F SVC FVC PMVF PMSVC PMFVC
F11.24 Monitoring parameter 0002
Unit: Output current display filter RUN
(0x0B18) filtering selection (0000 ~000F)
0~F: the larger the value, the deeper the filter
V/F SVC FVC PMVF PMSVC PMFVC
Display selection when
F11.25 Set the display selection when the motor is self-learning 0
the motor is self- STOP
(0x0B19) 0: Display self-learning process status 1: Do not display self-learning (0 ~ 1)
learning
process status
V/F SVC FVC PMVF PMSVC PMFVC
F11.27 0001
Fault display selection Unit: The fault is displayed when the fault recovers. RUN
(0x0B1B) (0000 ~ 0001)
0: Do not display 1: Display

4.15 F12：Communication Parameter

F12.0x：MODBUS Slave Parameter

Parameter Factory default Adjustable
Name Content
（Address） (range) properly
F12.00 V/F SVC FVC PMVF PMSVC PMFVC 0
Host-slave choice STOP
(0x0C00) 0：Slave，1：Host (0 ~ 1)

F12.01 Modbus V/F SVC FVC PMVF PMSVC PMFVC 1

communication STOP
(0x0C01) Set different values for different slaves. (1 ~ 247)
address
V/F SVC FVC PMVF PMSVC PMFVC
F12.02 Communication baud 0：1200 bps 1：2400 bps 2：4800 bps 3
STOP
(0x0C02) rate selection 3：9600 bps 4：19200 bps 5：38400 bps (0 ~ 6)
6：57600 bps
V/F SVC FVC PMVF PMSVC PMFVC
0: (N, 8, 1) no parity, data bits: 8, stop bits: 1
1: (E, 8, 1) even parity, data bits: 8, stop bits: 1
F12.03 0
Modbus data format 2: (O, 8, 1) odd parity, data bits: 8, stop bits: 1 STOP
(0x0C03) (0 ~ 5)
3: (N, 8, 2) no parity, data bits: 8, stop bits: 2
4: (E, 8, 2) even parity, data bits: 8, stop bits: 2
5: (O, 8, 2) odd parity, data bits: 8, stop bits: 2

38
RD11 Series Frequency converter Manual

F12.04 Modbus transmission V/F SVC FVC PMVF PMSVC PMFVC 0

RUN
(0x0C04) response processing 0: Write operation has a response 1: Write operation has no response (0 ~ 1)

Modbus
F12.05 V/F SVC FVC PMVF PMSVC PMFVC 0ms
communication RUN
(0x0C05) Set the time of Modbus communication response delay (0 ~ 500ms)
response delay
Modbus
F12.06 V/F SVC FVC PMVF PMSVC PMFVC 1.0s
communication timeout RUN
(0x0C06) Set the time of Modbus communication timeout failure (0.1 ~ 100.0s)
failure time
Communication V/F SVC FVC PMVF PMSVC PMFVC
F12.07 0
disconnection 0: Do not detect timeout failure 1: Fault and free stop RUN
(0x0C07) (0 ~ 3)
processing 2: Warning and continue to run 3: Forced stop
F12.08 Receive data (address V/F SVC FVC PMVF PMSVC PMFVC 0.00
RUN
(0x0C08) 0x3000) zero bias Offset correction communication data for address 0x3000. (-100.00-100.00)
F12.09 Receive data (address V/F SVC FVC PMVF PMSVC PMFVC 100.0%
RUN
(0x0C09) 0x3000) gain Linearly correct communication data of the address 0x3000. (0.0～500.0%)

F12.1x：MODBUS Host Parameter

Parameter Factory default Adjustable
Name Content
（Address） (range) properly
V/F SVC FVC PMVF PMSVC PMFVC
0: Invalid 1: Host run command
2: host given frequency 3: host output frequency
F12.10 Host cyclically send 4: Host upper limit frequency 5: Host given torque 0031
RUN
(0x0C0A) parameter selection 6: Host output torque 7: Reserved (0000 ~ CCCC)
8: Reserved 9: Host PID given
A: Host PID feedback B: Reserved
C: active current component
F12.11 Frequency given V/F SVC FVC PMVF PMSVC PMFVC 0000
RUN
(0x0C0B) custom address setting Set frequency given custom address (0000 ~ FFFF)
Command given
F12.12 V/F SVC FVC PMVF PMSVC PMFVC 0000
custom address RUN
(0x0C0C) Set command to give a custom address (0000 ~ FFFF)
settings
Command given as
F12.13 V/F SVC FVC PMVF PMSVC PMFVC 0001
forward run command RUN
(0x0C0D) The set command is given as the forward run command value. (0000 ~ FFFF)
value
Command given as
F12.14 V/F SVC FVC PMVF PMSVC PMFVC 0002
reverse run command RUN
(0x0C0E) The set command is given as the reverse run command value. (0000 ~ FFFF)
value
F12.15 Command given as V/F SVC FVC PMVF PMSVC PMFVC 0005
RUN
(0x0C0F) stop command value The set command is given as the stop command value. (0000 ~ FFFF)
F12.16 Command given as V/F SVC FVC PMVF PMSVC PMFVC 0007
RUN
(0x0C10) reset command value Set command as reset command value (0000 ~ FFFF)

F12.3x：Profibus-DP
Parameter Factory default Adjustable
Name Content
（Address） (range) properly
F12.30 V/F SVC FVC PMVF PMSVC PMFVC 1
DP card address RUN
(0x0C1E) Set the address of DP card (1 ~ 247)

F12.4x：CAN Mode
Parameter Factory default Adjustable
Name Content
（Address） (range) properly
F12.40 V/F SVC FVC PMVF PMSVC PMFVC 1
CAN mode selection RUN
(0x0C28) 0：Slave 1：Host station of VEDA-IN (0 ~ 1)
F12.41 Communication V/F SVC FVC PMVF PMSVC PMFVC 1
RUN
(0x0C29) address Set the address of the slave (1 ~ 247)
V/F SVC FVC PMVF PMSVC PMFVC
F12.42 Communication baud 0：20 kbps 1：50 kbps 2：100kbps 3
RUN
(0x0C2A) rate selection (0 ~ 6)
3：125kbps 4：250kbps 5：500kbps

39
RD11 Series Frequency converter Manual
6：1Mbps

F12.5x： EX-A,EX-B Communication

Parameter Factory default Adjustable
Name Content
（Address） (range) properly
V/F SVC FVC PMVF PMSVC PMFVC
Expansion port
Unit: EX-A port disconnection action mode
F12.50 communication 0000
0: No detection 1: Alarm and free stop 2: Warning and continue to run RUN
(0x0C32) disconnection (0000~0022)
Ten digits: EX-B port disconnection action mode
processing
0: No detection 1: Alarm and free stop 2: Warning and continue to run
V/F SVC FVC PMVF PMSVC PMFVC
F12.51 Expansion port EX-A 0
0: No update 1: The initial value has been updated after power-on RUN
(0x0C33) parameter update (0 ~ 2)
2: Expansion port EX-A parameter recovery initial value
V/F SVC FVC PMVF PMSVC PMFVC
F12.52 Expansion port EX-B 0
0: No update 1: The initial value has been updated after power-on RUN
(0x0C34) parameter update (0 ~ 2)
2: Expansion port EX-n parameter recovery initial value
Expansion port EX-A V/F SVC FVC PMVF PMSVC PMFVC
F12.53 0001
monitoring frame Ten digits: the lower address is 8 digits 00 to 63 RUN
(0x0C35) (0000 ~ 0763)
address group 1 Hundreds of thousands: address high 8 bits 00 ~ 07
Expansion port EX-A
F12.54 V/F SVC FVC PMVF PMSVC PMFVC 0002
monitoring frame RUN
(0x0C36) Ditto (0000 ~ 0763)
address group 2
Expansion port EX-A
F12.55 V/F SVC FVC PMVF PMSVC PMFVC 0007
monitoring frame RUN
(0x0C37) Ditto (0000 ~ 0763)
address group 3
Expansion port EX-A
F12.56 V/F SVC FVC PMVF PMSVC PMFVC 0011
monitoring frame RUN
(0x0C38) Ditto (0000 ~ 0763)
address group 4
Expansion port EX-B
F12.57 V/F SVC FVC PMVF PMSVC PMFVC 0001
monitoring frame RUN
(0x0C39) Ditto (0000 ~ 0763)
address group 1
Expansion port EX-B
F12.58 V/F SVC FVC PMVF PMSVC PMFVC 0002
monitoring frame RUN
(0x0C3A) Ditto (0000 ~ 0763)
address group 2
Expansion port EX-B
F12.59 V/F SVC FVC PMVF PMSVC PMFVC 0007
monitoring frame RUN
(0x0C3B) Ditto (0000 ~ 0763)
address group 3
Expansion port EX-B
F12.60 V/F SVC FVC PMVF PMSVC PMFVC 0011
monitoring frame RUN
(0x0C3C) Ditto (0000 ~ 0763)
address group 4

4.16 F13：Process PID Control

F13.00-F13.06: PID given and feedback

Parameter Factory default Adjustable
Name Content
（Address） (range) properly
V/F SVC FVC PMVF PMSVC PMFVC
0: Keyboard digital PID given 1: Keyboard analog potentiometer
given
F13.00 PID controller given 2: Current/voltage analog AI1 given 0
RUN
(0x0D00) signal source 3: Current/voltage analog AI2 given (0 ~ 9)
4: Reserved 5: Terminal pulse PUL given
6: RS485 communication reference 7: Option card
8: Terminal selection 9: Communication given active current

F13.01 Keyboard digital PID V/F SVC FVC PMVF PMSVC PMFVC 50.0%
RUN
(0x0D01) given / feedback Set keyboard digital PID given / feedback value (0.00～100.0%)

F13.02 V/F SVC FVC PMVF PMSVC PMFVC 1.00s

PID given change time RUN
(0x0D02) Set the PID given change time (0.00～60.00s)

40
RD11 Series Frequency converter Manual
V/F SVC FVC PMVF PMSVC PMFVC
0: keyboard digital PID feedback 1: keyboard analog potentiometer
feedback
F13.03 PID controller feedback 2: Current/voltage analog AI1 feedback 2
RUN
(0x0D03) signal source 3: Current/voltage analog AI2 feedback (0 ~ 9)
4: Reserved 5: Terminal pulse PUL feedback
6: RS485 communication feedback 7: Option card
8: Terminal selection 9: Local active current
F13.04 Feedback signal low V/F SVC FVC PMVF PMSVC PMFVC 0.010s
RUN
(0x0D04) pass filtering time Set the feedback signal low pass filter time (0.000～6.000s)
F13.05 V/F SVC FVC PMVF PMSVC PMFVC 1.00
Feedback signal gain RUN
(0x0D05) Set feedback signal gain (0.00～10.00)
F13.06 V/F SVC FVC PMVF PMSVC PMFVC 100.0
Feedback signal range RUN
(0x0D06) Set the feedback signal range (0～100.0)

F13.07-F13.24: PID Adjustment

Parameter Factory default Adjustable

Name Content
（Address） (range) properly
V/F SVC FVC PMVF PMSVC PMFVC
Unit position: feedback feature selection
F13.07 PID control 0100
0: Positive characteristic 1: Negative characteristic RUN
(0x0D07) selection (0000 ~ 1111)
Thousands: differential adjustment properties
0: Differentiate the deviation 1: Differentiate the feedback
F13.08 V/F SVC FVC PMVF PMSVC PMFVC 100.0%
PID preset output RUN
(0x0D08) Set PID preset output (0.0～100.0%)
F13.09 PID preset output V/F SVC FVC PMVF PMSVC PMFVC 0.0s
RUN
(0x0D09) running time Set PID preset output running time (0.0～6500.0s)
F13.10 PID control deviation V/F SVC FVC PMVF PMSVC PMFVC 0.0%
RUN
(0x0D0A) limit Set the PID control deviation limit (0.0～100.0%)
F13.11 V/F SVC FVC PMVF PMSVC PMFVC 0.100
Proportional gain P1 RUN
(0x0D0B) Set the proportional gain P1 (0.000～4.000)
F13.12 V/F SVC FVC PMVF PMSVC PMFVC 1.0s
Integration time I1 RUN
(0x0D0C) Set the integration time I1 (0.0～600.0s)
F13.13 V/F SVC FVC PMVF PMSVC PMFVC 0.000s
Differential gain D1 RUN
(0x0D0D) Set the differential gain D1 (0.000～6.000s)
F13.14 V/F SVC FVC PMVF PMSVC PMFVC 0.100
Proportional gain P2 RUN
(0x0D0E) Set the proportional gain P2 (0.000～4.000)
F13.15 V/F SVC FVC PMVF PMSVC PMFVC 1.0s
Integration time I2 RUN
(0x0D0F) Set the integration time I2 (0.0～600.0s)
F13.16 V/F SVC FVC PMVF PMSVC PMFVC 0.000s
Differential gain D2 RUN
(0x0D10) Set the differential gain D2 (0.000～6.000s)
V/F SVC FVC PMVF PMSVC PMFVC
F13.17 0
PID switch condition 0: Do not switch 1: Switch with DI terminal 2: Switch according to RUN
(0x0D11) (0 ~ 2)
deviation
V/F SVC FVC PMVF PMSVC PMFVC
F13.18 Switching deviation low 20.0%
Set the switching deviation low value. When the PID deviation is less RUN
(0x0D12) value （0.0～100.0%）
than this value, use the gain 1 parameter.
V/F SVC FVC PMVF PMSVC PMFVC
F13.19 Switching deviation 80.0%
Set the switching deviation high value. When the PID deviation is RUN
(0x0D13) high value （0.0～100.0%
greater than this value, use the gain 2 parameter.
F13.21 V/F SVC FVC PMVF PMSVC PMFVC 5.0%
Differential limiting RUN
(0x0D15) Set differential limit （0.0～100.0%）
F13.22 V/F SVC FVC PMVF PMSVC PMFVC 100.0%
PID output upper limit RUN
(0x0D16) Set the PID output limit （0.0～100.0%）
F13.23 V/F SVC FVC PMVF PMSVC PMFVC 0.0%
PID output lower limit RUN
(0x0D17) Set the PID output lower limit （-100.0～F13.22）
F13.24 V/F SVC FVC PMVF PMSVC PMFVC 0.000s
PID output filtering time RUN
(0x0D18) Set the PID output filter time (0.000～6.000s)

41
RD11 Series Frequency converter Manual
F13.25-F13.28: PID Feedback Disconnection judgment
Parameter Factory default Adjustable
Name Content
（Address） (range) properly
V/F SVC FVC PMVF PMSVC PMFVC
V/F SVC FVC PMVF PMSVC PMFVC
Feedback
F13.25 0: Continue PID operation without reporting fault 1: Stop and report 0
disconnection action STOP
(0x0D19) fault (0 ~ 3)
selection
2: Continue PID operation and output alarm signal
3: Run at the current frequency, output alarm signal
F13.26 Feedback V/F SVC FVC PMVF PMSVC PMFVC 1.0s
disconnection RUN
(0x0D1A) Set feedback disconnection detection time (0.0～120.0s)
detection time
F13.27 Wire break alarm V/F SVC FVC PMVF PMSVC PMFVC 100.0
RUN
(0x0D1B) upper limit Set the upper limit of the disconnection alarm (0.0～100.0%)
F13.28 Wire break alarm lower V/F SVC FVC PMVF PMSVC PMFVC 0.0%
RUN
(0x0D1C) limit Set the upper limit of the disconnection alarm (0.0～100.0%)

F13.29-F13.33: PID Sleeping Function

Parameter Factory default Adjustable
Name Content
（Address） (range) properly
V/F SVC FVC PMVF PMSVC PMFVC
F13.29 0
Sleep selection Set whether sleep is effective RUN
(0x0D1D) (0 ~ 1)
0: off 1: valid
10.00Hz
F13.30 V/F SVC FVC PMVF PMSVC PMFVC
Sleep frequency (0.00～Max RUN
(0x0D1E) Set sleep frequency
frequency)

F13.31 V/F SVC FVC PMVF PMSVC PMFVC 60.0S

Sleep delay RUN
(0x0D1F) Set the time of sleep delay (0.0～3600.0S)

F13.32 V/F SVC FVC PMVF PMSVC PMFVC 5.0%

Wake up deviation RUN
(0x0D20) Set wakeup deviation (0.0～50.0%)
F13.33 V/F SVC FVC PMVF PMSVC PMFVC 1.0S
Wake-up delay RUN
(0x0D21) Set wakeup delay (0.0～60.0S)

4.17 F14:Multi-speed and Simple PLC

F14.00~F14.14：Multi-speed given
Parameter Factory default Adjustable
Name Content
（Address） (range) properly
10.00Hz
F14.00 V/F SVC FVC PMVF PMSVC PMFVC
Multi-speed 1 (0.00～Max RUN
(0x0E00) Set PLC multi-speed 1
frequency)
20.00Hz
F14.01 V/F SVC FVC PMVF PMSVC PMFVC
Multi-speed 2 (0.00~ Max RUN
(0x0E01) Set PLC multi-speed 2
frequency)
30.00Hz
F14.02 V/F SVC FVC PMVF PMSVC PMFVC
Multi-speed 3 (0.00~ Max RUN
(0x0E02) Set PLC multi-speed 3
frequency)
40.00Hz
F14.03 V/F SVC FVC PMVF PMSVC PMFVC
Multi-speed 4 (0.00~Max RUN
(0x0E03) Set PLC multi-speed 4
frequency)
50.00Hz
F14.04 V/F SVC FVC PMVF PMSVC PMFVC
Multi-speed 5 (0.00~ Max RUN
(0x0E04) Set PLC multi-speed 5
frequency)
40.00Hz
F14.05 V/F SVC FVC PMVF PMSVC PMFVC
Multi-speed 6 (0.00~ Max RUN
(0x0E05) Set PLC multi-speed 6
frequency)
30.00Hz
F14.06 V/F SVC FVC PMVF PMSVC PMFVC
Multi-speed 7 (0.00~ Max RUN
(0x0E06) Set PLC multi-speed 7
frequency)

42
RD11 Series Frequency converter Manual
20.00Hz
F14.07 V/F SVC FVC PMVF PMSVC PMFVC
Multi-speed 8 (0.00~ Max RUN
(0x0E07) Set PLC multi-speed 8
frequency)
10.00Hz
F14.08 V/F SVC FVC PMVF PMSVC PMFVC
Multi-speed 9 (0.00～Max RUN
(0x0E08) Set PLC multi-speed 9
frequency)
20.00Hz
F14.09 V/F SVC FVC PMVF PMSVC PMFVC
Multi-speed 10 (0.00~ Max RUN
(0x0E09) Set PLC multi-speed 10
frequency)
30.00Hz
F14.10 V/F SVC FVC PMVF PMSVC PMFVC
Multi-speed 11 (0.00~ Max RUN
(0x0E0A) Set PLC multi-speed 11
frequency)
40.00Hz
F14.11 V/F SVC FVC PMVF PMSVC PMFVC
Multi-speed 12 (0.00~Max RUN
(0x0E0B) Set PLC multi-speed 12
frequency)

50.00Hz
F14.12 V/F SVC FVC PMVF PMSVC PMFVC
Multi-speed 12 (0.00~Max RUN
(0x0E0C) Set PLC multi-speed 12
frequency)
40.00Hz
F14.13 V/F SVC FVC PMVF PMSVC PMFVC
Multi-speed 14 (0.00~Max RUN
(0x0E0D) Set PLC multi-speed 14
frequency)
30.00Hz
F14.14 V/F SVC FVC PMVF PMSVC PMFVC
Multi-speed 15 (0.00~ Max RUN
(0x0E0E) Set PLC multi-speed 15
frequency)

F14. 15：PLC Operation Mode Selection

Parameter Factory default Adjustable
Name Content
（Address） (range) properly
V/F SVC FVC PMVF PMSVC PMFVC
Unit position: cycle mode
0: Stop after single cycle 1: Continuous cycle 2: Keep the final value
after single cycle
Ten place: timing unit
F14.15 PLC Operation mode 0: second 1: minute 2: hour 0000
RUN
(0x0E0F) selection Hundreds: Power-down storage (0000 ~ 2122)
0: no storage 1: storage
Thousands: Startup mode
0: Re-run from the first stage
1: Re-run from the phase of the downtime
2: continue to run for the rest of the downtime phase

F14.16~F14.30：PLC Operation Time Selection

Parameter Factory default Adjustable
Name Content
（Address） (range) properly
F14.16 PLC 1st stage running V/F SVC FVC PMVF PMSVC PMFVC 10.0
RUN
(0x0E10) time Set PLC 1st stage running time (0.0～6500.0(s/m/h))
10.0
F14.17 PLC 2nd stage running V/F SVC FVC PMVF PMSVC PMFVC
(0.0～ RUN
(0x0E11) time Set PLC 2nd stage running time
6500.0(s/m/h))
10.0
F14.18 PLC 3rd stage running V/F SVC FVC PMVF PMSVC PMFVC
(0.0～ RUN
(0x0E12) time Set PLC 3rd stage running time
6500.0(s/m/h))
10.0
F14.19 PLC 4th stage running V/F SVC FVC PMVF PMSVC PMFVC
(0.0～ RUN
(0x0E13) time Set PLC 4th stage running time
6500.0(s/m/h))
10.0
F14.20 PLC 5th stage running V/F SVC FVC PMVF PMSVC PMFVC
(0.0～ RUN
(0x0E14) time Set PLC 5th stage running time
6500.0(s/m/h))
10.0
F14.21 PLC 6th stage running V/F SVC FVC PMVF PMSVC PMFVC
(0.0～ RUN
(0x0E15) time Set PLC 6th stage running time
6500.0(s/m/h))
10.0
F14.22 PLC 7th stage running V/F SVC FVC PMVF PMSVC PMFVC
(0.0～ RUN
(0x0E16) time Set PLC 7th stage running time
6500.0(s/m/h))

43
RD11 Series Frequency converter Manual
10.0
F14.23 PLC 8th stage running V/F SVC FVC PMVF PMSVC PMFVC
(0.0～ RUN
(0x0E17) time Set PLC 8h stage running time
6500.0(s/m/h))
10.0
F14.24 PLC 9th stage running V/F SVC FVC PMVF PMSVC PMFVC
(0.0～ RUN
(0x0E18) time Set PLC 9th stage running time
6500.0(s/m/h))
10.0
F14.25 PLC 10th stage V/F SVC FVC PMVF PMSVC PMFVC
(0.0～ RUN
(0x0E19) running time Set PLC 10th stage running time
6500.0(s/m/h))
10.0
F14.26 PLC11th stage running V/F SVC FVC PMVF PMSVC PMFVC
(0.0～ RUN
(0x0E1A) time Set PLC 11th stage running time
6500.0(s/m/h))
10.0
F14.27 PLC 12th stage V/F SVC FVC PMVF PMSVC PMFVC
(0.0～ RUN
(0x0E1B) running time Set PLC 12th stage running time
6500.0(s/m/h))
10.0
F14.28 PLC 13th stage V/F SVC FVC PMVF PMSVC PMFVC
(0.0～ RUN
(0x0E1C) running time Set PLC 13th stage running time
6500.0(s/m/h))
F14.29 PLC 14th stage V/F SVC FVC PMVF PMSVC PMFVC 10.0
RUN
(0x0E1D) running time Set PLC 14th stage running time (0.0～6500.0(s/m/h))
10.0
F14.30 PLC 15th stage V/F SVC FVC PMVF PMSVC PMFVC
(0.0～ RUN
(0x0E1E) running time Set PLC 15th stage running time
6500.0(s/m/h))

F14.31~F14.45：PLC Operation Direction and Time Selection

Parameter Factory default Adjustable
Name Content
（Address） (range) properly
V/F SVC FVC PMVF PMSVC PMFVC
Unitt: The running direction of this segment (compared with the
running command)
PLC direction and
0: same direction 1: reverse
F14.31 acceleration and 0000
Ten digits: acceleration and deceleration time of this section RUN
(0x0E1F) deceleration time of 1st (0000~0031)
0: Acceleration/deceleration time 1 1: Acceleration/deceleration time
stage
2
2: Acceleration/deceleration time 3 3: Acceleration/deceleration time
4
PLC direction and
F14.32 acceleration and V/F SVC FVC PMVF PMSVC PMFVC 0000
RUN
(0x0E20) deceleration time of The same settings as F14.31 (0000~0031)
2nd stage
PLC direction and
F14.33 acceleration and V/F SVC FVC PMVF PMSVC PMFVC 0000
RUN
(0x0E21) deceleration time of 3rd The same settings as F14.31 (0000~0031)
stage
PLC direction and
F14.34 acceleration and V/F SVC FVC PMVF PMSVC PMFVC 0000
RUN
(0x0E22) deceleration time of 4th The same settings as F14.31 (0000~0031)
stage
PLC direction and
F14.35 acceleration and V/F SVC FVC PMVF PMSVC PMFVC 0000
RUN
(0x0E23) deceleration time of 5th The same settings as F14.31 (0000~0031)
stage
PLC direction and
F14.36 acceleration and V/F SVC FVC PMVF PMSVC PMFVC 0000
RUN
(0x0E24) deceleration time of 6th The same settings as F14.31 (0000~0031)
stage
PLC direction and
F14.37 acceleration and V/F SVC FVC PMVF PMSVC PMFVC 0000
RUN
(0x0E25) deceleration time of 7th The same settings as F14.31 (0000~0031)
stage
PLC direction and
F14.38 acceleration and V/F SVC FVC PMVF PMSVC PMFVC 0000
RUN
(0x0E26) deceleration time of 8th The same settings as F14.31 (0000~0031)
stage
F14.39 PLC direction and V/F SVC FVC PMVF PMSVC PMFVC 0000
RUN
(0x0E27) acceleration and The same settings as F14.31 (0000~0031)

44
RD11 Series Frequency converter Manual
deceleration time of 9h
stage
PLC direction and
F14.40 acceleration and V/F SVC FVC PMVF PMSVC PMFVC 0000
RUN
(0x0E28) deceleration time of The same settings as F14.31 (0000~0031)
10th stage
PLC direction and
F14.41 acceleration and V/F SVC FVC PMVF PMSVC PMFVC 0000
RUN
(0x0E29) deceleration time of The same settings as F14.31 (0000~0031)
11th stage
PLC direction and
F14.42 acceleration and V/F SVC FVC PMVF PMSVC PMFVC 0000
RUN
(0x0E2A) deceleration time of The same settings as F14.31 (0000~0031)
12th stage
PLC direction and
F14.43 acceleration and V/F SVC FVC PMVF PMSVC PMFVC 0000
RUN
(0x0E2B) deceleration time of The same settings as F14.31 (0000~0031)
13th stage
PLC direction and
F14.44 acceleration and V/F SVC FVC PMVF PMSVC PMFVC 0000
RUN
(0x0E2C) deceleration time of The same settings as F14.31 (0000~0031)
14th stage
PLC direction and
F14.45 acceleration and V/F SVC FVC PMVF PMSVC PMFVC 0000
RUN
(0x0E2D) deceleration time of The same settings as F14.31 (0000~0031)
154th stage

4.18 C0x：Monitoring Parameter

C00：Basic Monitoring
Parameter Name Parameter Name
（Address） （Address）
C00.00 (0x2100) Given frequency C00.20 (0x2114) Analog output AO
C00.01 (0x2101) Output frequency C00.21 (0x2115) Reserved
C00.02(0x2102) Output current C00.22 (0x2116) Counter count value
C00.03 (0x2103) Input voltage C00.23 (0x2117) Power-on running time
Accumulated running time of the
C00.04 (0x2104) The output voltage C00.24 (0x2118)
machine
C00.05 (0x2105) Mechanical speed C00.25 (0x2119) Inverter power level
C00.06 (0x2106) Given torque C00.26 (0x211A) Inverter rated voltage
C00.07 (0x2107) Output torque C00.27 (0x211B) Inverter rated current
C00.08 (0x2108) PID given C00.28 (0x211C) Software version
C00.09 (0x2109) PID feedback C00.29 (0x211D) PG feedback frequency
C00.10 (0x210A) Output Power C00.30 (0x211E) Timer timing
C00.11 (0x210B) bus voltage C00.31 (0x211F) PID output value
C00.12 (0x210C) Module temperature 1 C00.32 (0x2120) Inverter software subversion
C00.13 (0x210D) Module temperature 2 C00.33(0x2121) Encoder feedback angle
C00.14 (0x210E) Input terminal X is on (Note) C00.34 (0x2122) Z pulse cumulative error
C00.15 (0x210F) Output terminal Y is on (Note) C00.35 (0x2123) Z pulse count
C00.16(0x2110) Analog AI1 input value C00.36 (0x2124) Failure warning code
Cumulative power consumption
C00.17 (0x2111) Analog AI2 input value C00.37 (0x2125)
(low level)
Cumulative power consumption
C00.18 (0x2112) Keyboard potentiometer input value C00.38 (0x2126)
(high)
C00.19 (0x2113) Pulse signal PUL input value C00.39 (0x2127) Power factor angle

Note：For example, when terminals X1 and X2 are ON, C00.14 is displayed as ，When terminal Y and relay are ON, C00.15 is displayed

as 。

45
RD11 Series Frequency converter Manual
C01：Fault Monitoring
Parameter Name Parameter（Address） Name
（Address） The first fault operation
C01.00 (0x2200) Fault type C01.12 (0x220C)
frequency
C01.01 (0x2201) Troubleshooting information C01.13 (0x220D) Last fault output voltage
C01.02 (0x2202) Fault operating frequency C01.14 (0x220E) Last fault output current
C01.03 (0x2203) Fault output voltage C01.15 (0x220F) The first fault bus voltage
The first fault module
C01.04 (0x2204) Fault output current C01.16 (0x2210)
temperature
C01.05 (0x2205) Fault bus voltage C01.17 (0x2211) The first faulty inverter status

C01.06 (0x2206) Faulty module temperature C01.18 (0x2212) The first fault input terminal
status
C01.07 (0x2207) Faulty inverter status C01.19 (0x2213) The first fault output terminal
status
C01.08 (0x2208) Fault input terminal status C01.20 (0x2214) First 2 fault types
The first 2 troubleshooting
C01.09 (0x2209) Fault output terminal status C01.21 (0x2215)
information
C01.10 (0x220A) Previous failure type C01.22 (0x2216) Top 3 fault types
Previous troubleshooting The first 3 troubleshooting
C01.11 (0x220B) C01.23 (0x2217)
information information

C02：Application Monitoring
Parameter（Address） Name Parameter（Address） Name

C02.00 (0x2300) PID feedback C02.08 (0x2308) Fwd and Rev command given

C02.01 (0x2301) PID given C02.09 (0x2309) Jog command given

C02.02 (0x2302) PID output C02.60 (0x233C) Expansion card A version
C02.03 (0x2303) PID control status C02.61 (0x233D) Expansion card B version
C02.05 (0x2305) PLC operation phase C02.62 (0x233E) External keyboard version
C02.06 (0x2306) PLC phase frequency C02.63 (0x233F) Built-in keyboard version
C02.07 (0x2307) PLC phase running time

4.19 Terminal Selection Function

Terminal X Function Interpretation Terminal X Function Interpretation Terminal X Function Interpretation

0 No function 21 PID control pause 42 Counter clock input terminal

1 Forward running 22 PID characteristic switching 43 Counter clear terminal
2 Reverse run 23 PID parameter switching 44 DC brake command
Pre-excitation command
3 Three-wire operation control (Xi) 24 PID given switch 1 45
terminal
4 Forward turn 25 PID given switch 2 46 Reserved
5 Reverse jog 26 PID given switch 3 47 Reserved

6 Free parking 27 PID feedback switching 1 48 Command channel switch to

keyboard
7 emergency pull over 28 PID feedback switching 2 49 Command channel switch to
terminal
8 Fault reset 29 PID feedback switching 3 50 Command channel switch to
communication
9 External fault input 30 Program run (PLC) pause 51 Command channel switch to
expansion card
10 Frequency increment (UP) 31 Program run (PLC) restart 52 Run prohibition
Acceleration/deceleration time
11 Frequency decrement (DW) 32 53 Forward prohibition
selection terminal 1
12 Frequency increment decrement 33 Acceleration/deceleration time 54 Reverse prohibition
clear (UP/DW clear) selection terminal 2
13 Channel A switches to channel B 34 Suspension acceleration 55 Reserved

46
RD11 Series Frequency converter Manual
Switch the frequency channel
14 35 Swing frequency input 56 Reserved
combination to A
Switch the frequency channel
15 36 Swing frequency pause 57 Zero servo command
combination to B
16 Multi-speed terminal 1 37 Swing frequency reset 58 Run output blocking
command
17 Multi-speed terminal 2 38 Keyboard button and display self- 59 Reserved
test selection
X5 or X10 (extended) frequency Speed torque control
18 Multi-speed terminal 3 39 60
measurement switching
19 Multi-speed terminal 4 40 Timer trigger terminal 61 Reserved
20 PID control canceled 41 Timer clear terminal 62 Reserved

Terminal Y Function Interpretation Terminal Y Function Interpretation Terminal Y Function Interpretation

0 no output 14 Lower limit frequency arrival 28 Underload pre-alarm output 2

1 The inverter is running 15 Program run cycle completion 29 Inverter warning
The running phase of the program Communication address
2 Inverter running in reverse 16 30
is completed. 0x3018 control output

3 The inverter is running in forward 17 PID feedback exceeds the upper 31 Inverter overheat warning
rotation limit
Fault trip alarm 1 (alarm during PID feedback is below the lower
4 18 32 Motor overheat alarm output
fault self-recovery) limit
Fault trip alarm 2 (no alarm during PID feedback sensor Frequency (speed) is
5 19 33
fault self-recovery) disconnection consistent 1
Any frequency (speed) is
6 External downtime 20 Meter length arrives 34
consistent 1
7 Inverter undervoltage 21 Timer time to 35 Frequency detection 1
8 The inverter is ready for operation 22 Counter reaches maximum 36 Frequency detection 2
Output frequency level detection 1 Frequency (speed) is
9 23 Counter reaches the set value 37
(FDT1) consistent 2

Output frequency level detection 2 Any frequency (speed) is

10 24 Energy consumption braking 38
(FDT2) consistent 2
11 Arrived at a given frequency 25 PG feedback disconnection 39 Frequency detection 3
12 Zero speed operation 26 Emergency stop 40 Frequency detection 4
13 Upper limit frequency arrival 27 Overload pre-alarm output 1

4.20 Fault and Warning Code Table

Note: The numbers in parentheses are fault codes or warning codes (Dec. means decimal).

Keyboard display Keyboard display

Fault name Fault type Fault name Fault type
(Dec.) (Dec.)

E.SC1（1） Accelerated system failure Fault E.LD1（79） Load protection 1 Fault

E.SC2（2） System failure during deceleration Fault E.LD2（80） Load protection 2 Fault
E.SC3（3） Constant speed system failure Fault E.CPU（81） CPU timeout failure Fault
E.SC4（4） Downtime system failure Fault E.LOC（85） Chip lock Fault
E.OC1（5） Overcurrent in acceleration Fault E.EEP（86） Parameter storage failure Fault
E.OC2（6） Overcurrent during deceleration Fault E.PLL（87） Phase-locked loop failure Fault
E.OC3（7） Overcurrent at constant speed Fault E.BUS1（91） Expansion card A disconnected Fault
E.OU1（9） Accelerating overvoltage Fault E.BUS2（92） Expansion card B is broken Fault
E.OU2（10） Overvoltage during deceleration Fault E.BUS3（93） CAN expansion card failure Fault
E.OU3（11） Overvoltage at constant speed Fault E.BUS4（94） Other expansion card failure Fault
E.LU（13） Undervoltage in operation Fault E.BUS5（95） Other expansion card failure Fault
E.OL1（14） Motor overload Fault E.BUS6（96） Other expansion card disconnection Fault
E.OL2（15） Inverter overload 1 Fault E.CP1（97） Monitor compare output 1 fault Fault

47
RD11 Series Frequency converter Manual
E.OL3（16） Inverter overload 2 continuous CBC Fault E.CP2（98） Monitor compare output 2 fault Fault

E.OL4（17） Inverter overload 3 Fault E.DAT（99） Parameter setting error Fault

E.ILF（18） Input phase loss Fault E.FA1（110） External extension reserve 1 Fault
E.OLF（19） Three phase output phase loss Fault E.FA2（111） External extension reserve 2 Fault
E.OLF1（20） U phase output phase loss Fault E.FA3（112） External extension reserve 3 Fault
E.OLF2（21） V phase output phase loss Fault E.FA4（113） External extension reserve 4 Fault
E.OLF3（22） W phase output phase loss Fault E.FA5（114） External extension reserve 5 Fault
E.OH1（30） Rectifier module over temperature Fault E.FA6（115） External extension reserve 6 Fault
E.OH2（31） IGBT module over temperature Fault E.FA7（116） External extension reserve 7 Fault
E.OH3（32） Motor over temperature Fault E.FA8（117） External extension reserve 8 Fault
E.EF（33） External fault Fault
The following is the warning code
E.CE（34） Modbus communication failure Fault
E.HAL1（35） U phase zero drift excessive Fault A.LU1（128） Undervoltage during stopping Warning
E.HAL2（36） V phase zero drift excessive Fault A.OU（129） Overvoltage during stopping Warning
E.HAL（37） Sum of Three-phase current is not 0 fault Fault A.ILF（130） Input phase loss Warning
E.HAL3（38） W phase zero drift excessive Fault A.PID（131） PID feedback disconnection Warning
E.SGxx（40） Short circuit to ground Fault A.EEP（132） Parameter storage warning Warning
E.FSG（41） Fan short circuit Fault A.DEF（133） Speed deviation excessive Warning
E.PID（42） PID feedback disconnection Fault A.SPD（134） Speed warning Warning
E.COP（43） Parameter copy failure Fault A.GPS1（135） GPS locked Warning
E.PG1（44） PG parameter setting error Fault A.GPS2（136） GPS disconnection Warning
E.PG2（44） Encoder Z pulse failure Fault A.CE（137） External warning Warning
E.PG3（44） Rotation check error Fault A.LD1（138） Load protection 1 Warning
E.PG4（44） Rotational disconnection Fault A.LD2（139） Load protection 2 Warning
Expansion card disconnection
E.PG5（44） ABZ encoder disconnection Fault A.BUS（140） Warning
warning
E.PG6（44） Spindle encoder disconnection Fault A.OH1（141） Module over temperature warning Warning

E.PG7（44） Spindle encoder Z pulse error fault Fault A.OH3（142） Motor over temperature warning Warning

E.PG8（44） Encoder Z pulse logic fault Fault A.RUN1（143） Run command conflict Warning

E.PG9（44） Spindle encoder Z pulse logic fault Fault A.RUN2（158） Jog terminal start protection Warning

E.PG10（44） Encoder Z pulse disconnection Fault A.RUN3（159） Terminal start protection Warning
External keyboard disconnection
E.BRU（50） Brake unit failure Fault A.PA2（144） Warning
warning
E.TExx（52） Motor parameter self-learning fault Fault A.COP（145） Parameter copy warning Warning

E.IAE1（71） Motor angle learning fault 1 Fault A.CP1（146） Monitor comparison output 1 warning Warning

E.IAE2（72） Motor angle learning fault 2 Fault A.CP2（147） Monitor comparison output 2 warning Warning
E.IAE3（73） Motor angle learning fault 3 Fault A.FA1（150） External extension reserve 1 Warning

E.PST1（74） Synchronous machine out of step fault 1 Fault A.FA2（151） External extension reserve 2 Warning

E.PST2（75） Synchronous machine out of step fault 2 Fault A.FA3（152） External extension reserve 3 Warning

E.PST3（76） Synchronous machine out of step fault 3 Fault A.FA4（153） External extension reserve 4 Warning
E.DEF（77） Speed deviation excessive Fault A.FA5（154） External extension reserve 5 Warning
E.SPD（78） Speed exceed fault Fault A.FA6（155） External extension reserve 6 Warning

5 Inspection, Maintenance and Guarantee

48
RD11 Series Frequency converter Manual
5.1 Inspection
The frequency converter consists of semiconductor devices, passive electronic components, and moving devices. These devices have a service life. Even under normal
working conditions, some devices may have characteristic changes or failures if they exceed the service life. In order to prevent this phenomenon from causing malfunctions,
it is necessary to perform preventive inspection and maintenance such as daily inspection, periodic inspection, and device replacement. It is recommended to check every 3
or 4 months after installation.
● Daily inspection: In order to avoid damage to the inverter and shorten the service life, please confirm the following items daily.。
Items Content Solution
Check if the power supply voltage meets the requirements and whether there is Resolve as required on the nameplate.
Power supply a lack of phase power supply.
Surroundings Whether the installation environment meets the requirements. Confirm the source and solve it properly.
Whether the inverter and the motor have abnormal heating and discoloration, Check if the overload, fixing screw, and the heat sink of the
cooling system and check the working status of cooling fans . inverter are dirty, and check if the fan is blocked.
Whether the motor has abnormal vibration and abnormal sound. Fasten mechanical and electrical connections and lubricate
Motor
mechanical parts.
Whether the output current of the inverter is higher than the rated value of the Check if an overload condition occurs and confirm that the model
Load condition
motor or the inverter for a certain period of time. of the inverter is selected correctly.
● Regular inspection: In general, it is advisable to conduct regular inspections every 3 months or 4 months, but in actual cases, please determine the actual inspection
period based on the use of each machine and the working environment.
Items Content Solution
Fasten and replace bad parts; clean and improve the operating
overall Insulation resistance check; environmental inspection. environment.
● Replace damaged wires;
● Whether the wires and connections are discolored, whether the insulation is
● Tighten the loose terminals and replace the damaged
Electrical damaged, cracked, discolored, or aged;
terminals;
connections ● Whether the connection terminals are worn, damaged or loose;
● Measure the grounding resistance and tighten the
● Grounding check.
corresponding grounding terminal.
Mechanical ● Fasten, lubricate, and replace defective parts.
● Whether there is abnormal vibration and noise, and whether there is looseness.
connection
Semiconductor ● Whether it is contaminated with garbage and dust; ● Whether there is a ● Clean the operating environment; ● Replace damaged parts.
components significant change in appearance.
Electrolytic ● Whether it leaks, discolors, cracks, whether the safety valve is exposed, swells, ● Replace damaged parts.
capacitor ruptures or leaks.
peripheral ● Clean the environment and replace damaged parts.
● Peripheral device appearance and insulation inspection.
equipment
● Fasten the connector;
A printed circuit ● Whether there is odor, discoloration, severe rust, and the connector is correct
● Clean the printed circuit board;
board and reliable.
● Replace damaged printed circuit boards;
● Whether the cooling fan is damaged or blocked; ● Clean the operating environment;
● Whether the heat sink is stained with dirt, dust and dirt; ● Replace damaged parts.
cooling system
● Whether the air inlet and exhaust port are blocked or contaminated with foreign
matter.
keyboard ● Whether the keyboard is damaged or defective. ● Replace damaged parts.
● Fasten mechanical and electrical connections and lubricate
Motor ● Whether the keyboard is damaged or defective. the motor shaft.

： Do not perform related work while the power is on, otherwise there is a danger of death due to electric shock. When performing related work,
please cut off the power supply and confirm that the DC voltage of the main circuit has dropped to a safe level, and wait 5 minutes before performing related work.

49
RD11 Series Frequency converter Manual
5.2 Maintenance
All equipment and components have a service life. Proper maintenance can extend the life, but it cannot solve the damage of equipment and equipment. Please replace
the equipment according to requirements.
Item Service life Item Service life Item Service life
Fans 2~3 years Electrolytic capacitor 4~5 years PCB 8~10 years

The replacement of other devices is very strict with the maintenance technology and product familiarity, and must be strictly tested before being replaced before use.
Therefore, it is not recommended to replace other internal components. If you do need to replace it, please contact the agent where you purchased the product or the sales
department of the company.

5.3 Product Warranty

1. The product during the warranty period is faulty. For details, please refer to the warranty terms in the warranty card.
2. Primary fault diagnosis is implemented by customs’ company in principle, but can be provided by our company or our company's service network according to the
requirements of your company. According to the results of negotiations with your company, the company will provide free services for the reasons of the failure.
3. Liability exemption, due to the company's product failure, the inconvenience caused to your company or your company's customers and the damage caused by non-
Company products, whether within the warranty period or not, are not within the scope of the company's responsibility.

50
RD11 Series Frequency converter Manual

Appendix I: Modbus Communication Protocol

●Communication frame structure
The communication data format is as follows:
The composition of the byte: including the start bit, 8 data bits, check bit and stop bit.

Start Bit Bit1 Bit2 Bit3 Bit4 Bit5 Bit6 Bit7 Bit8 Check bit Stop bit

The information of a frame must be transmitted in a continuous stream. If the interval of more than 1.5 bytes before the end of the entire frame transmission, the receiving
device will clear the incomplete information and mistakenly believe that the next byte is the address field portion of a new frame. Similarly, if the interval between the start of a
new frame and the previous frame is less than 3.5 bytes, the receiving device will consider it to be the continuation of the previous frame. Due to the disorder of the frame, the
CRC check value is incorrect, resulting in communication error.
Standard structure of RTU frames:

Frame header 3.5 bytes of transmission time

mailing address:
Slave address
0 to 247 (decimal) (0 is the broadcast address)
03H: Read slave parameters
Command code 06H: Write slave parameters
08H: Loop self-test
Data area Parameter address, number of parameters, parameter value, etc.

Low CRC CHK

Detection value: 16-bit CRC check value
High CRC CHK

End of frame 3.5 bytes of transmission time

●Command code and communication data description

Take the read parameter command code as an example.
For example, if the slave address is 01H, the memory start address is 2100H (monitoring parameter C00.00), and if three consecutive words are read, the structure of
the frame is described as follows:

RTU host command information RTU slave response information (normal)

Slave address 01H Host address 01H
Command code 03H Command code 03H
High start address 21H Low number of bytes 06H
Low start address 00H High data address2100H 13H
High number of data 00H Low data address 2100H 88H
Low number of data 03H High data address 2101H 00H
Low CRC CHK 0FH Low data address 2101H 00H
High CRC CHK F7H High data address 2102H 00H
Low data address 2102H 00H
Low CRC CHK 90H
High CRC CHK A6H
RTU slave response information (abnormal)

51
RD11 Series Frequency converter Manual
Slave address 01H
Command code 83H
Fault code 04H
Low CRC CHK 40H
High CRC CHK F3H

●Communication control parameter group address description

Address
Function Description Data meaning Characteristics
Definition
Communication given 0x3000 or 0x2000 0～32000 correspond to 0.00Hz～320.00Hz W/R
frequency
0x0005:Dec stop
0x0000:no command 0x0006:free stop
0x0001:FWD run 0x0007:Fault reset
Communication command
0x3001 or 0x2001 0x0002:REV run 0x0008:Run prohibition W/R
setting
0x0003:FWD Jog command
0x0004:REV Jog 0x0009:Run permission
command
Bit0 0:Stop status 1:Running status
Bit1 0:Non-Acc 1:Acc status
status
0:Non-Dec
Bit2 1:Dec status
status
Inverter status 0x3002 or 0x2002 Bit3 0:Foward 1:Reverse R
Bit4 0:No fault 1:Inverter fault
Bit5 0:GPRS unlock 1:GPRS locked
Bit6 0:No warning 1:Inverter
Inverter fault code 0x3003 or 0x2003 Inverter current fault code (see faultwarning
code table) R
Communication given upper
0x3004 or 0x2004 0～32000 correspond to 0.00Hz～320.00Hz W/R
limit frequency
Communication torque setting 0x3005 or 0x2005 0～1000 correspond to 0.0～100.0% W/R
Torque control positive
0x3006 or 0x2006 0～1000 correspond to 0.0～100.0% W/R
maximum frequency limit
Torque control reverse
0x3007 or 0x2007 0～1000 correspond to 0.0～100.0% W/R
maximum frequency limit
Communication given PID set
0x3008 or 0x2008 0～1000 correspond to 0.0～100.0% W/R
value
Communication given PID
0x3009 or 0x2009 0～1000 correspond to 0.0～100.0% W/R
feedback value
Fault and warning code
0x3010 or 0x2010 Fault code:0～127 Warning code:128 and above R
reading
External inverter output terminal,
Bit0 – Y
Output terminal status 0x3018 or 0x2018 Bit1-- TA1-TB1-TC1; R
Bit2 – extended Y1 (with IO expansion card)
BIT3 -- Extended relay (with IO expansion card)
AO output 0x3019 or 0x2019 0-10000 correspond to Output 0-10V/0-20mA R
Note: For other function code addresses, see the “Address” column in the function code profile
When using the writing command (06H) to write the F00~F15 parameters, if the function code parameter address field high nibble is 0, only write in the
inverter RAM, won’t be stored when power down; if the function code parameter address field high nibble is 1, written in the EEPROM, and will be stored when
power down.
For example parameter F00.xx: 0x00xx (write in RAM), 0x10xx (stored in EEPROM); parameter F01.xx: 0x01xx (write in RAM) 0x11xx (stored in EEPROM), and so on,
for other parameters. When reading the F00~F15 parameter group parameters, the address high nibble is 0, such as reading the parameter F03.xx: 0x03xx.
When using the write command (06H) to write F16~F29 parameters, if the function code parameter address field high nibble is 5, only write in to the inverter

52
RD11 Series Frequency converter Manual
RAM, won’t be stored when power down; if the function code parameter address field high nibble is D, written in the EEPROM, will be stored when power down.
For example, parameter F16.xx: 0x50xx (write in RAM) 0xD0xx (stored in EEPROM); parameter F17.xx: 0x51xx (write in RAM) 0xD1xx (stored in EEPROM), and so
on other group parameters. When reading the F16~F29 parameter group parameters, the address high nibble is 5, such as reading the parameter F18.xx: 0x52xx.

●The error code meaning of slave abnormal response information

Code Description Code Description Code Description
1 Command code error 3 CRC check error 4 Illegal address
Parameter cannot be modified The inverter is busy (EEPROM is
5 Illegal data 6 8
during running being stored)
Reserved parameter cannot be The number of bytes is incorrect when
9 Parameter value exceed 10 11
modified reading parameter.

53
RD11 Series Frequency converter Manual

Appendix II: Terminal wiring method

0：Two-wire control 1

The operation is in one direction. This mode is the most commonly used two-wire mode. The factory default is to determine the forward and reverse running of the motor
by the X1 (forward running) and X2 (reverse running) terminal commands. As shown below:

0: Two-wire control 1 schematic

1：Two-wire control 2
The operation is separated from the direction. The forward running terminal X1 (forward running) defined in this mode is the operation enable terminal. The definition of
the direction is determined by the state of the reverse running terminal X2 (reverse running). As shown below:

1: Two-wire control 2 schematic

2：Three-wire control 1
In this mode, the three-wire operation control terminal (Xi) is the stop operation terminal, and the running command is generated by the forward rotation operation terminal

X1 (forward rotation operation), and the direction is controlled by the reverse rotation operation terminal X2 (reverse rotation operation). The three-wire operation control

terminal (Xi) is an effective input.

frequency inverter
SB1 SB2 X1
run order(run while on)

K1 direction control Xi stop order(stop while off)

0 FWD
K1 X2
1 REV FWD/REV order(run while close)

COM common input port

2: 3-line 1

2: Three-wire control 1 schematic

3：Three-wire control 2
In this mode, the three-wire operation control terminal (Xi) is the stop operation terminal, and the operation command is generated by the forward rotation operation
terminal X1 (forward rotation operation) or the reverse rotation operation terminal X2 (reverse rotation operation), and both control the running direction.

54
RD11 Series Frequency converter Manual

3: Three-wire control 2 schematic

Hint: SB1: stop button; SB2: forward run button; SB3: reverse run button; "Xi" is the multi-function input terminal when set to "3" [three-wire operation control (Xi)]。

55