PROJECT REPORT

PRINTED CIRCUIT BOARDS

PRINTED CIRCUIT BOARD MANUFACTURING A. PROCESS DESCRIPTION Printed circuit boards are electronic circuits created by mounting electronic components on a nonconductive board, and creating conductive connections between them. The creation of circuit patterns is accomplished using both additive and subtractive methods. The conductive circuit is generally copper, although aluminum, nickel, chrome, and other metals are sometimes used. There are three basic varieties of printed circuit boards: single-sided, double-sided, and multi-layered. The spatial and density requirement and the circuitry complexity determine the type of board produced. Printed circuit boards are employed in the manufacturing of business machines and computers, as well as communication, control, and home entertainment equipment. Production of printed circuit boards involves the plating and selective etching of flat circuits of copper supported on a nonconductive sheet of plastic. Production begins with a sheet of plastic laminated with a thin layer of copper foil. Holes are drilled through the board using an automated drilling machine. The holes are used to mount electronic components on the board and to provide a conductive circuit from one layer of the board to another. Following drilling, the board is scrubbed to remove fine copper particles left by the drill. The rinse water from a scrubber unit can be a significant source of copper waste. In the scrubber, the copper is in a particulate form and can be removed by filtration or centrifuge. Equipment is available to remove this copper particulate, allowing recycle of the rinse water to the scrubber. However, once mixed with other waste streams, the copper can dissolve and contribute to the dissolved copper load on the treatment plant. After being scrubbed, the board is cleaned and etched to promote good adhesion and then is plated with an additional layer of copper. Since the holes are not conductive, electroless cop- per plating is employed to provide a thin continuous conductive layer over the surface of the board and through the holes. Electroless copper plating involves using chelating agents to keep the copper in solution at an alkaline pH. Plating depletes the metal and alkalinity of the electroless bath. Copper sulfate and caustic are added (usually automatically) as solutions, resulting in a growth in volume of the plating solution. This growth is a significant source of copper-bearing wastewater in the circuit board industry. Treatment of this stream (and the rinsewater from electroless plating) is complicated by the presence of chelating agents, making simple hydroxide precipitation ineffective. Iron salts can be added to break the chelate, but only at the cost of producing a significant volume of sludge. Ion exchange is used to strip the copper from the chelating agent, typically by using a chelating ion exchange resin. Regeneration of the ion exchange resin with sulfuric acid produces a concentrated copper sulfate solution without the chelate. This regenerant can then be either treated by hydroxide precipitation, producing hazardous waste sludge, or else concentrated to produce a useful product.

Growth from electroless copper plating is typically too concentrated in copper to treat directly byion exchange. Different methods have been employed to reduce the concentration of copper sufficiently either to discharge the effluent directly to the sewer or to treat it with ion exchange. One method, reported by Hewlett-Packard, replenishes growth with formaldehyde and caustic soda to enhance its autocatalytic plating tendency, and then mixes it with carbon granules on which the copper plates out in a form suitable for reclaiming. Following electroless plating a plating resist is applied to the panel and photo-imaged to create the circuit design. Copper is then electroplated on the board to its final thickness. A thin layer of tin lead solder or pure tin is plated over the copper as an etch resist. The plating resist is then removed to expose the copper not part of the final circuit pattern. The exposed copper is then removed by etching to reveal the circuit pattern. Ammonia-based etching solutions are most widely used. Use of ammonia complicates waste treatment and makes recovery of copper difficult. An alternative to ammonia etching is sulfuric acid/hydrogen peroxide etching solutions. This latter etchant is continuously replenished by adding concentrated peroxide and acid as the copper concentration increases to about 80 g/L. At this concentration, the solution is cooled to precipitate out copper sulfate. After replenishing with peroxide and acid, the etchant is reused. Disadvantages of the sulfuric acid-peroxide etching solution are that it is relatively slow when compared with ammonia, and controlling temperature can be difficult.

Indian PCB Market Size

An Impressive 17% CAGR growing PCB demand

14470 731 533 1570 177 17780

17724 790 580 1950 185 21589

21800 850 630 2440 195 26355

26800 950 685 2930 200 32095

32500 1050 730 3550 210 38665

38350 1150 780 4250 220 45470

17.64 % 7.84% 6.55% 18.05 % 3.69% 17.00 %