HOW TO CHANGE CHART DISPLAY

DISPLAY – SET – CHART DISPLAY– PUT OR REMOVE ON BOXES – SAVE – CLOSE

HOW TO SAVE CURRENT CHART DISPLAY SETTING TO PROFILE
PROFILE – MANAGE PROFILE – SELECT PROFILE WHERE YOU WANT TO SAVE – CLICK SAVE CURRENT
SETTINGS
HOW TO DISABLE PROFILE
PROFILE – MANAGE PROFILE – SELECT PROFILE YOU WANT TO DISABLE – PUT  ON DISABLE BOX – CLOSE
*NOTE:ACTIVE PROFILE CANNOT BE DISABLE
HOW TO EXPORT (WHOLE DATA ON ECDIS)
PROFILE – SETTINGS – OK – EXPORT – PUT  ON BOX FOR THE DATA YOU WANT TO EXPORT – EXPORT –
DOUBLE CLICK ON USB FLASH / CD/DVD – CHANGE FILENAME IF YOU WANT BUT RETAIN FILE
EXTENSION(EX. .TXT/.ZIP/.JPG)–SAVE – OK
HOW TO IMPORT
PROFILE – SETTINGS – OK – IMPORT – SELECT FILE TO IMPORT – DOUBLE CLICK ON USB FLASH /CD/DVD –
SELECT FILE TO IMPORT – OPEN – PUT ON THE BOX – IMPORT
FILE MAINTENANCE
PROFILE – SETTINGS– OK– FILE MAINTENANCE – PUT ON BOXES ROUTE/USERCHART APPLICATION OR
ROUTE/USERCHART SYSTEM BACK UP – RESTORE
HOW TO PERFORM SELF TEST
PROFILE – SETTINGS – OK –SELF TEST – CLICK START – SELECT EXPORT IF YOU WANT TO EXPORT
*NOTE : NO INTERNAL RECORD FOR SELF TEST
CUSTOMIZE
PROFILE – SETTINGS – OK – CUSTOMIZE – ADJUST WHEEL POSITION NORMAL OR REVERSE – KEY BEEP
VOLUME – ALERT SOUND VOLUME
HOW TO PERFORM DISPLAY TEST
PROFILE – SETTINGS – OK –DISPLAY TEST – CLICK DIPLAY TEST BUTTON – LEFT CLICK TO PROCEED TO NEXT
DISPLAY PATTERN – PRESS ESC TO EXIT
HOW TO PERFORM KEYBOARD TEST
PROFILE – SETTINGS –KEYBOARD TEST – PRESS ON YOUR KEYBOARD PANEL
HOW TO LOCATE CAPTURE SCREENSHOT
PROFILE – SETTINGS – OK –SCREENSHOT
HOW TO MAKE CAPTURE SCREENSHOT
BOTTOM LEFT CORNER – CAMERA ICON – LEFT CLICK
HOW TO LOCATE MANUAL
CLICK ? – MANUAL
HOW TO USE MANUAL
CLICK ON THE TOPIC ON THE LEFT – PUT CURSOR ON THE CENTER SCREEN – SCROLL DOWN OR UP TO
CHANGE PAGES
TO FIND TOPIC CLICK EDIT – FIND – ON THE FIND BOX AT BOTTOM LEFT TYPE THE TOPIC - CLICK FIND NEXT TO
FIND FOR THE NEXT ANSWER
TO ZOOM - ZOOM IN ZOOM OUT ICON

HOW TO LOCATE VERSION AND APPLIED STANDARDS

CLICK ?– ABOUT – VERSION /APPLIED STANDARDS
HOW TO CHANGE IMO DISPLAY
CLICK ON IMO DISPLAY– IMO BASE / IMO STANDARD / IMO ALL
*REFERS TO LAYERS OF INFORMATION YOU CAN SEE ON YOUR ECDIS SCREEN
 BASE DISPLAY – means the information that cannot be removed from the display. It is not intended to be
sufficient for safe navigation.
 STANDARD DISPLAY – is the display mode intended to be used as a minimum during route planning and
route monitoring.

List of information onBASE DISPLAY

 Coastline (high water)
 Own ship safety contour
 Isolated underwater dangers of depths less than the safety contour which lie within the safe waters
defined by the safety contour
 Isolated dangers which lie within the safe water defined by the safety contour such as fixed structures,
overhead wires etc.
 Scale, range and north arrow
 Units of depth and height
 Display mode
 Annex 24 resolution MSC.232(82) (adopted on December 5 2006)
ADOPTION OF THE REVISED PERFORMANCE STANDARDS FOR ECDIS

HOW TO CHANGE IMO CHART DISPLAY SETTING

DISPLAY – SET – CHART DISPLAY – PUT OR REMOVE ON BOXES OF INFORMATION YOU WANT TO DISPLAY
OR REMOVE ON YOUR CHART DISPLAY – SAVE – CLOSE
*NOTE :CHANGES ON CHART DISPLAY SETTINGS THE IMO DISPLAY BECOME CUSTOM OR CUSTOMIZE
HOW TO SELECT CHART VECTOR TO RASTER CHART OR VICE VERSA
CLICK ON VECTOR CHART ICON – DROP DOWN MENU CHOOSE VECTOR CHART OR RASTER CHART
STANDARD DISPLAY ICON – SHORTCUT BUTTON FOR STANDARD DISPLAY
CHART ONLY – LEFT CLICKHOLD IT WILL REMOVE TEMPORARILY ALL AIS / TARGET DISPLAY ON SCREEN
CLEAR RADAR – SHORTCUT BUTTON FOR SWITCH OFF RADAR OVERLAY DISPLAY

OTHERS

HOW TO REMOVE AUDIBLE ALARM OR PUT ECDIS ON SILENT MODE

OTHERS – STANDBY – ENTER PASSWORD (3000)– OK
HOW TO SEE PLAYBACK
OTHERS – PLAYBACK – SELECT DATE – OK

HOW TO LOCATE CHART SYMBOL REFERENCE

CHART INFO – CHART 1
HOW TO VIEW CHART ON DIFFERENT DATE
CHART INFO – VIEWING DATES –SET DATE MANUALLY– OK
HOW TO RETURN ON CURRENT DATE DISPLAY
CHART INFO – VIEWING DATES – SELECT AUTO – OK
HOW TO KNOW CHART INFORMATION
PUT CURSOR ON CHART THEN RIGHT CLICK – SELECT CHART LEGEND
HOW TO PUT MAGNETIC VARIATION ON CHART LEGEND
PUT IMO DISPLAY TO ALL – ZOOM IN /ZOOM OUT ON CHART UNTIL YOU SEE OR SEARCH FOR THIS SYMBOL
PUT CURSOR ON THIS SYMBOL THEN RIGTH CLICK – SELECT CHART LEGEND

DISPLAY MODE

HOW TO SWICTH ON / OFF VIRTUAL KEYBOARD

DISPLAY – SELECT KEYBOARD ICON – ON / OFF
HOW TO DISPLAY / OFF NtoM (NOTICE TO MARINERS)
DISPLAY – NtoM – AIO – ALL to appear / OFF to hide
HOW TO SHOW TWO DISPLAY ON SCREEN
DISPLAY – TWO DISPLAY – SELECT VERTICAL / HORIZONTALDISPLAY
HOW TO ADJUST BASIC SETTING ON CHART SYMBOLS DISPLAY
DISPLAY – SET – BASIC SETTING – AFTER YOU MADE ADJUSTMENT CLICK SAVE – CLOSE
HOW TO CHANGE OVER FROM SYSTEM SENSOR TO LOCAL SENSOR
DISPLAY – SET – BASIC SETTING – SENSORS – SYSTEM/LOCAL SENSOR – CLICK SYSTEM OR LOCAL SENSOR
TO CHANGE – SAVE
HOW TO ADJUST LOCAL SENSOR SETTINGS
DISPLAY – SET –BASIC SETTING – LOCAL SENSOR SETTING – AFTER YOU MADE ADJUSTMENT CLICK SAVE-
CLOSE
HOW TO SET SYMBOLS DISPLAY
DISPLAY – SET – SYMBOLS DISPLAY - AFTER YOU MADE ADJUSTMENT CLICK SAVE - CLOSE
HOW TO SET CHART ALERT DISPLAY
DISPLAY – SET – CHART ALERT DISPLAY - AFTER YOU MADE ADJUSTMENT CLICK SAVE- CLOSE
HOW TO SET SAFETY CONTOUR
DISPLAY – SET – CHART ALERT –SAFETY CONTOUR BOXES –ENTER FIRST THE VALUE OF SAFETY CONTOUR
THEN YOU CAN PROCEED FOR THE REST –SAVE – CLOSE

LOG

HOW TO SHOW DANGER TARGET LOG

LOG – TARGET LOG – DANGER TARGET LOG
HOW TO SHOW LOG FOR CHART UPDATES / INSTALL
LOG– CHART LOG – ENC
HOW TO SHOW VOYAGE LOG / DETAIL LOG / CHART USAGE
LOG– NAV LOG – SELECT VOYAGE LOG / DETAIL LOG / CHART USAGE
HOW TO SHOW PREVIOUS SHIPS TRACK
LOG– NAV LOG – VOYAGE LOG / DETAILED LOG –SET DATE AND TIME – SHOW TRACK
HOW TO MAKE USER EVENT
LOG– EVENT LOG – USER EVENT – TYPE DESCRIPTION – OK
HOW TO KNOW INFORMATION ON USER EVENT MARK
PUT CURSOR ON USER EVENT MARK THEN LEFT CLICK OR LOG– NAV LOG – VOYAGE LOG – SELECT / SEARCH
USER EVENT YOU MADE SCROLL GOING TO RIGHT END SELECT DESCRIPTION FOR DETAILS
*NOTE: USER EVENT MADE POSITION AND TIME CANNOT BE EDITED EXCEPT FOR DESCRIPTION

HOW TO PLOT THROUGH GPS

LOG – EVENT LOG – POSITION EVENT – CHANGE LOP TO POSITION – CLICK RECORD
HOW TO PLOT MANUALLY
LOG – EVENT LOG – POSITION EVENT – CHANGE LOP TO MANUAL – CLICK RECORD
HOW TO MAKE LOP
LOG – EVENT LOG – POSITION EVENT–CHANGE TRUE BEARING TO TRUE BEARING + DISTANCE – CLICK ON
SIGHTED OBJECT – CHANGE VALUE OF BEARING AND DISTANCE ACCORDING TO RADAR DATA – CLICK ADD
FOR ANOTHER LOP – CLICK ON SIGHTED OBJECT – CHANGE VALUE OF BEARING AND DISTANCE ACCORDING
TO RADAR DATA – CLICK ADD (IF YOU WANT TO ADD ANOTHER LOP FOLLOW PROCEDURE ABOVE) OR
CLICK RECORDTO PLOT OR CLICK D.R. FOR DEAD RECKONING PLOT

HOW TO DELETE LOP

AFTER YOU PLOT THE FIRST LOP EACH TIME YOU CLICK ADD BUTTON THE DELETE BUTTON BECOMES ACTIVE
YOU CAN PRESS DELETE OR CLEAR ALL LINES IF NECESSARY TO DELETE

WHERE TO FIND RECORDS OF POSITION EVENT MADE?

LOG – NAV LOG – VOYAGE LOG – SELECT OR SEARCH POSITION EVENT MADE SCROLL GOING TO RIGHT END
SELECT DESCRIPTION FOR DETAILS
*NOTE: ALL POSITION EVENT MADE POSITION AND TIME CANNOT BE EDITED

HOW TO MAKE MOB

CLICK MOB ICON BOTTOM LEFT

HOW TO HIDE MOB MARK

PUT CURSOR ON MOB MARK THEN RIGHT CLICK – SELECT HIDE
*NOTE: MOB RECORDED ON VOYAGE LOG YOU CAN EDIT THE DESCRIPTION BUT NOT THE POSTION AND TIME

PLAN MODE

HOW TO MAKE ROUTE PLAN

PLAN – PLANNING – ROUTE – NEW – CLICK ON CHART FOR WAYPOINTS – RIGHT CLICK TO FINISH –
OPTIMIZE
(INPUT YOUR ETD) – ALERT PARAMETERS (UKC &DRAFT) – CHECK ROUTE – CHECK RESULTS ONE BY ONE –
SAVE – TYPE FILE NAME – OK

HOW TO EDIT ROUTE PLAN

 PUT CURSOR ANYWHERE ON THE WAYPOINTS THEN RIGHT CLICK – SELECT EDIT –LEFT CLICK ON
WAYPOINTS AND DRAG TO CHANGE POSITION/ TO INSERT WAYPOINT PLACE CURSOR ALONG THE COURSE
LINE AND RIGHT CLICK AGAIN TO INSERT / DELETE WAYPOINTS – RIGHT CLICK SELECT FINISH ONCE DONE

HOW TO KNOW IF ROUTE PLAN IS SAVE

1. EXCHANGE TO MONITOR BUTTON IS ACTIVATED
2. THE ASTRISK SYMBOL ON YOUR FILE NAME IS GONE
EXAMPLE:
*JUAN DELA CRUZ ------- UNSAVED
JUAN DELA CRUZ ------- SAVED

*AFTER YOU SAVED YOUR ROUTE PLAN DO NOT UNSELECT PROCEED TO PLANNING AND SELECT USER CHART
FOLLOW GUIDE BELOW

HOW TO MAKE USER CHART

PLAN – PLANNING – USER CHART – NEW – SELECT ON USER CHART SYMBOLS : TIDAL / LINE / CLEARING LINE
/ AREA / CIRCLE / LABLES – CLICK ON CHART WHERE YOU WANT TO PLACE IT – SAVE – TYPE FILENAME – OK
– CLOSE
*NOTE: SIZE / COLOR AND DIRECTION OF LABELS IS STANDARD

HOW TO LINKED USER CHART TO ROUTE PLAN

PLAN – PLANNING – ROUTE – SELECT ROUTE PLAN YOU MADE –USER CHART – SELECT SAVED USER CHART
TO LINK THEN PUT  ON THE BOX – – CHECK ROUTE AGAIN – SAVE

HOW TO SEE YOUR ROUTE PLAN AND USER CHART ON PAPER FORM
PLAN – REPORT – ROUTE – PASSAGE / USER CHART – SELECT ROUTE PLAN/ USER CHART – OPEN

HOW TO DELETE / EXPORT ROUTE PLAN

PLAN – MANAGE DATA – ROUTE – SELECT ROUTE PLAN PUT  ON THE BOX – CHANGE FILE TYPE TO CSV /
ASCII – DELETE TO DELETE / EXPORT TO EXPORT

HOW TO IMPORT ROUTE PLAN

PLAN – MANAGE DATA – ROUTE – IMPORT – DOUBLE CLICK USB FLASH – SELECT FILE TO IMPORT – OPEN/
OK

HOW TO DELETE USER CHART

PLAN – MANAGE DATA – USER CHART – SELECT USER CHART PUT  ON THE BOX – DELETE

CHARTS

SEQUENCE IN LOADING UPDATES: PERMIT BASE – UPDATES – AIO (TEMPORARY & PRELIMINARY)

HOW TO LOAD UPDATES THROUGH CD / DVD

 CHARTS – INSERT CD / DVD ON DVD-ROOM– AUTO LOAD – OK – FOLLOW ON SCREEN INSTRUCTION – ONCE
FINISH REMOVE CD/DVD ON DVD – ROOM

HOW TO LOAD UPDATES THROUGH USB FLASH

CHARTS – INSERT USB FLASH – AUTO IMPORT – OK – SELECT – DOUBLE CLICK ON USB FLASH SELECT BASE /
UPDATE / AIO – OPEN – FOLLOW ON SCREEN INSTRUCTION

*NOTE: LOAD ONE UPDATE AT A TIME MEANING YOU HAVE TO DO IT THREE TIMES FOLLOWING THE SAME
INSTRUCTION: LOAD BASE FIRST THEN UPDATES THEN AIO

HOW TO LOAD PERMIT OR LICENSE THROUGH USB FLASH OR CD

CHARTS – LICENSE – INSTALL LICENSE – DOUBLE CLICK ON USB FLASH OR CD – SELECT PERMIT.TXT – OPEN –
OK

HOW TO MANUALLY LOAD PERMIT OR LICENSE

CHARTS – LICENSE – INPUT MANUALLY – TYPE MANUALLY LICENSE NUMBER ON THE DESCRIPTION BOX- OK
– FOLLOW ON SCREEN INSTRUCTION

HOW TO BACK UP / RESTORE LICENSE

CHARTS – LICENSE – BACK UP / RESTORE – ONE CLICK ON USB FLASH / CD – ONE CLICK ON OK - OK

HOW TO KOW WHAT CHART TO USE ON YOUR ROUTE PLAN

CHARTS – MANAGE CHARTS – FILTER BOXPUT ON ROUTE BOX THEN SELECT YOUR SAVED ROUTE PLAN –
APPLY

HOW TO KNOW CHARTS STATUS IF UPDATED (EDITION AND ISSUED)

CHARTS – CELL STATUS – FILTER BOX PUT ON ROUTE BOX THEN SELECT YOUR SAVED ROUTE PLAN –
APPLY

NAVI MODE

HOW TO ACTIVATE ROUTE PLAN

NAVI – VOYAGE – ROUTE – SELECT – SELECT ROUTE PLAN TO MONITOR – OK

HOW TO ACTIVATE USER CHART

NAVI – VOYAGE – USER CHART – SELECT USER CHART TO MONITOR – OK

HOW TO DEACTIVATE ROUTE PLAN OR USER CHART

NAVI – VOYAGE – STOP MONITOR

WHERE TO FIND MONITORING INFORMATION?

NAVI – VOYAGE – MONITOR INFO

HOW TO SEE NAVTEX MESSAGES

NAVI – MESSAGE – NAVTEX /SAFETY MESSAGE
HOW TO USE WEATHER OVERLAY

NAVI – CLICK - SELECT TYPE OF WEATHER INFORTION ON DROP DOWN MENU – OPEN

*NOTE: AFTER USE MAKE SURE TO CLEAR BEFORE CLOSING TO REMOVE OVERLAY FROM THE DISPLAY

HOW TO MAKE MANUAL UPDATE

NAVI – MANUAL UPDATE – PLANNING – ADD – SELECT DRAWING OBJECT: POINT / LINE / AREA CLICK ON
THE OBJECT – CLICK ON CHART – ADJUST DISPLAY DATE UNTIL / ADD DESCRIPTION / ATTRIBUTES – COMMIT
*NOTE: DISPLAY MODE MUST BE ON IMO ALL

HOW TO DELETE / MODIFY MANUAL UPDATE

NAVI – MANUAL UPDATE – LIST – SELECT MANUAL UPDATE (ONCE YOU SELECTED THE MANUAL UPDATE
THE DELETEAND MODIFY BUTTON BECOMES ACTIVE) PRESSREMOVETO DELETE OR MODIFY TO CHANGE THE DATE
DISPLAY UNTIL AND DESCRIPTION / ATTRIBUTES – COMMIT

HOW TO ACTIVATE / DEACTIVATE MINI CONNING

NAVI – MINI CONNING

*NOTE: TO CHANGE THE POSITION OF THE MINI CONNING DISPLAY RIGHT CLICK ON ITS DISPLAY THEN SELECT THE
POSITION WHERE YOU WANT TO PLACE IT

HOW TO SET UP YOU CONTOUR SETTINGS

SHALLOW CONTOUR = DEEPEST DRAFT =

SAFETY DEPTH = SAFETY CONTOUR =

SAFETY CONTOUR = DEEPEST DRAFT + UKC (SMS)↓ = 20% (As for FURUNO Manual)
COMPANY POLICY
DEEP CONTOUR = 2X DEEPEST DRAFT
HOW TO CHANGE TIME DISPLAY FROM UTC TO LOCAL TIME AND VICE VERSA
click on DATE DISPLAY icon- each time you click TIME DISPLAY beside changes

fromUTC to LOCAL TIME DIPLAY

DATE DISPLAY TIME DISPLAY

HOW TO ADJUST LOCAL TIME

Click on DATE DISPLAY then right click - click adjust local time - first box left – left click to change (- to +) – second
box and third box - enter your ZONE DESCRIPTION VALUE

HOW TO CHOOSE PROFILE TO USE

Click on the icon shown below then left click on your desired profile to use

PROFILE
HOW TO MANAGE PROFILE

1. Click DISP or DISPLAY 2. Set 3. CHART DISP 4. Adjust chart information display by putting 