Scribd
Upload
10 views

Useful Pipe Engineering Formulas and Basics

Uploaded by

Ahmed bassam
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
10 views

Useful Pipe Engineering Formulas and Basics

Uploaded by

Ahmed bassam
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 18

www.pdfstall.

online
www.pdfstall.online
www.pdfstall.online
www.pdfstall.online

www.pdfstall.online
www.pdfstall.online
www.pdfstall.online
www.pdfstall.online
www.pdfstall.online
www.pdfstall.online
www.pdfstall.online
www.pdfstall.online

Velocity of Fluid through Piping :-

0.3208 X GPM / Internal Area

What is the velocity of 10 gpm going through a 1/2″ diameter schedule 40 pipe?

GPM = 10
Internal Area = 0.304 (see note below)
0.3208 X GPM / Internal Area = 0.3208 X 10 X 0.304 = 10.55 feet per second

Note: The outside diameter of pipe remains the same regardless of the thickness of the
pipe. A heavy duty pipe has a thicker wall than a standard duty pipe, so the internal
diameter of the heavy duty pipe is smaller than the internal diameter of a standard
duty pipe. The wall thickness and internal diameter of pipes can be found on readily
available charts.
Hydraulic steel tubing also maintains the same outside diameter regardless of wall
thickness.

Hose sizes indicate the inside diameter of the plumbing. A 1/2″ diameter hose has an
internal diameter of 0.50 inches, regardless of the hose pressure rating.

www.pdfstall.online

Suggested Piping Sizes :-


Pump suction lines should be sized so the fluid velocity is between 2 and 4 feet per
second.
Oil return lines should be sized so the fluid velocity is between 10 and 15 feet per
second.
Medium pressure supply lines should be sized so the fluid velocity is between 15 and
20 feet per second.
High pressure supply lines should be sized so the fluid velocity is below 30 feet per
second.

Pneumatic Valve Sizing :-

Notes:
All these pneumatic formulas assume 68 degrees F at sea level
All strokes and diameters are in inches
All times are in seconds
All pressures are PSI.

Valve Sizing for Cylinder Actuation

SCFM = 0.0273 x Cylinder Diameter x Cylinder Diameter x Cylinder Stroke / Stroke


Time x ((Pressure-Pressure Drop)+14.7) / 14.7

Cv Required = 1.024 x SCFM / (Square Root of (Pressure Drop x (Pressure-Pressure


Drop+14.7)))

Pressure 2 (PSIG) = Pressure-Pressure Drop

www.pdfstall.online
Flow Coefficient for Smooth Wall Tubing

Cv of Tubing =(42.3 x Tube I.D. x Tube I.D. x 0.7854 x (Square Root (Tube I.D. /
0.02 x Length of Tube x 12)

AIR FLOW Q (IN SCFM) TO ATMOSPHERE

SCFM to Atmosphere = Valve Cv x (Square Root of (((Primary Pressure x 0.46) +


14.7) x (Primary Pressure x 0.54))) / 1.024

Pressure Drop Max (PSIG) = Primary Pressure x 0.54

Air Flow Q (in SCFM) if Cv is Known

Valve Cv x (Square Root of (Pressure Drop x ((PSIG – Pressure Drop) + 14.7))) /


1.024

CV IF AIR FLOW Q (IN SCFM) IS KNOWN

1.024 x Air Flow / (Square Root of (Pressure Drop x ((PSIG-Pressure Drop) + 14.7)))
www.pdfstall.online

You might also like