TABLE TOP PRO

HIGH-BUILD CLEAR RESIN SYSTEM FOR TABLES, BARS AND ART

TECHNICAL DATA BULLETIN

SYSTEM BENEFITS:
The MAS Table Top Pro Epoxy System is a 100% solids, two-component system. It has a one-to-one by volume mix ratio and
cures at room temperature. It can be used for tabletops, bar tops and art. It cures to a clear, glass-like finish that resists
scratching and yellowing. The system demonstrates excellent anti-blushing properties and will not distort with age.
• Cures clear for a high-gloss durable finish
• Ideal for bars and tabletops to protect wood from damage
• Versatile product can be used on art, tables, small castings and other projects

HANDLING PROPERTIES MAS TABLE TOP PRO Test Method

Resin Density at 25C, lbs/gal 9.7 ASTM D1475
Hardener Density at 25C, lbs/gal 8.1 ASTM D1475
Resin Viscosity at 25C, cP 9,000 ASTM D2196
Hardener Viscosity at 25C, cP 1,750 ASTM D2196
Mix Ratio by Weight 100A : 83B Calculated
Mix Ratio by Volume 1A : 1B Calculated
Initial Mixed Viscosity 25C, cP 3,500 ASTM D2196
Gel Time at 25C, 150g mass, min. 30 ASTM D2471

PHYSICAL PROPERTIES MAS TABLE TOP PRO Test Method

Color Clear Visual
Izod Impact, Notched, ft-lb/in 0.76 ASTM D256
Tensile Strength, psi 7,400 ASTM D638
Tensile Modulus, psi 382,000 ASTM D638
Tensile Elongation, % 5.9 ASTM D638
HDT, Room Temp Cure, F 118 ASTM D648
HDT, Post Cure, F 124 ASTM D648
Compressive Strength, psi 10,400 ASTM D695
Flexural Strength, psi 12,800 ASTM D790
Flexural Modulus, psi 373,000 ASTM D790
3 3
Cured Density, g/cm (lbs/in ) 1.11 (0.040) ASTM D792
3
Volumetric Yield, in /lb 25.0 ASTM D792
Volumetric Shrinkage, % 3.85 ASTM D792/2196
Hardness, Shore D 82 ASTM D2240

275 Bridgepoint Way | South St. Paul | MN | 55075 masepoxies.com (800) 755-8568
MAS TABLE TOP PRO
PAGE 2 OF 2

INSTRUCTIONS FOR USE:

For best results this product should be used at 70-80°F. A thin seal coat should first be applied to the tabletop or bar top and
any objects that will be imbedded. Delicate objects that may be damaged by epoxy resin such as photographs may needed to
be sealed with an alternate clear coat (i.e. polyurethane or acrylic sealers) to protect them prior to imbedding. Once the seal
coat has set, additional flood coats up to 1/8” thick may be applied. The MAS Table Top Epoxy Resin System can usually be
recoated in 4-8 hours without any additional prep work or sanding. If the previous layer is allowed to fully dry, the surface
should be scuff sanded with 220-320 grit sandpaper for optimal adhesion between coats. After sanding the surface should be
wiped with a solvent such as acetone or denatured alcohol to remove dust and other contaminants. Allow the surface to dry
before applying the next coat. Although resistant to yellowing, this product is not recommended for continuous outdoor
exposure to UV light and finishes may slowly lose their gloss or discolor over time if left outdoors. For product application
tutorial and additional information visit www.masepoxies.com or call at 1-800-755-8568.

MIXING AND HANDLING:

Combine the epoxy resin (Part A) and hardener (Part B) at the specified mix ratio of 1 to 1 by volume and mix for 3-5 minutes
or until mixture is thoroughly blended. Take care when mixing not to entrain excessive air in the mixture. Always use clean
dry tools for mixing and applying. Flood coats will flow and self level, but tools such as brushes, plastic spreaders and squeegees
may be used to help spread the mixed epoxy resin. A few minutes after the coat is applied bubbles will rise to the surface. A
propane torch held six inches above the surface of the epoxy resin may be used to break bubbles by slowly sweeping the torch
back and forth over the surface until bubbles disappear.

STORAGE AND CRYSTALLIZATION:

Store between 60-90F in a dry place. After use, tightly reseal all containers and store products on a raised surface during cold
weather and avoid storing near outside walls or doors. If available, purge with dry nitrogen to preserve color and minimize
moisture contamination. Do not allow to freeze during winter storage. Do not use material with any signs of crystallization
such as solid chunks, grainy texture or white color. Crystallization can be reversed by heating the material to 125-140F, and
stirring occasionally, until all crystals dissolve.

SAFETY HANDLING:
Wear protective gloves, clothing, and eye/face protection. Use only outdoors or in a well-ventilated area. Avoid contact to
the skin and eyes. Avoid breathing dust, fumes, gas mist, vapors and spray. Wash hands thoroughly after handling. Take off
contaminated clothing and wash before reuse. These products may cause skin and respiratory allergic reactions. Consult
product Safety Data Sheets for complete precautions for use of this product.

Endurance Technologies, Inc. has experience only in the compounding of resins and hardeners and not in the actual manufacture of tools or
parts. Each piece is different. The user should run tests to assure the suitability of the system for use in a particular application. The test
data and results set forth herein are based on laboratory work and do not necessarily indicate the results that the buyer or user will attain.

Endurance Technologies, Inc. makes no warranty expressed or implied, including warranties of merchantability or fitness for a particular use.
Under no circumstances will Endurance Technologies, Inc. be liable for incidental, consequential or other damages, alleged negligence,
breach of warranty, strict liability, tort or any other legal theory arising out of the use or handling of this product.

Revised December 2019

275 Bridgepoint Way | South St. Paul | MN | 55075 masepoxies.com (800) 755-8568