Scribd
Upload
67 views

Hlk-rm08k User Manual- Uart to Wifi Client Mode

Uploaded by

lt3congtan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
67 views

Hlk-rm08k User Manual- Uart to Wifi Client Mode

Uploaded by

lt3congtan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 7

Shenzhen Hi-Link Electronic Co.

,Ltd
Http://www.hlktech.ltd Tel:0755-83575155 Fax:0755-83575189

SHENZHEN HI- LINK ELECTRONIC CO.,LTD

HLK-RM08K USER MANUAL

UART to WIFI application (Client mode)


Shenzhen Hi-Link Electronic Co.,Ltd
Http://www.hlktech.ltd Tel:0755-83575155 Fax:0755-83575189

Kindly note : The starter kit includes the following items.

HLK-RM08K module

HLK-RM08K development board

2.4G Antenna

5V 1000mA power adapter

Net Cable（if needed）


Shenzhen Hi-Link Electronic Co.,Ltd
Http://www.hlktech.ltd Tel:0755-83575155 Fax:0755-83575189

一. Brief introduction

HLK-RM08K is a new low-cost embedded UART-ETH-WIFI module (serial port - Ethernet -


Wireless
network) developed by Shenzhen Hi-Link co., Ltd
This product is an embedded module based on the universal serial interface network standard, built-in
TCP / IP protocol stack, enabling the user serial port, Ethernet, wireless network (wifi) interface between
the conversions.
Through the HLK-RM08K module, the traditional serial devices do not need to change any
configuration; data can be transmitted through the Internet network. Provide a quick solution for the
user’s serial devices to transfer data via Ethernet.

二. UART to WIFI (Client mode ) configuration

Method 1: UART configuration


1. Restore factory setting. Power on 5V/350MA, and wait for 20s. Pull down ES1 pin more then 6S
after setting up. The system will restart automatically. Then the system is on the factory mode.

2. Power on module and wait for 10s until the LED is flashing.Make the connection of two uart ports
of DB9 and PC.Or use USB-UART cable connect the HLK-RM08K development board.
Picture for reference ：
Shenzhen Hi-Link Electronic Co.,Ltd
Http://www.hlktech.ltd Tel:0755-83575155 Fax:0755-83575189

3. Short press ESO button, start the configuration tool,choose the uart number then click search
module. It will return at (:Found Device at COM7(115200)! in the text box.Click inquiry configuration
to read the current parameters.

4. Configuration parameters
Working mode select: Client mode
Network protocol select: TCP server
Network IP: The remote IP doesn't work as a server
Port :TCP server set monitoring port.
UART parameter: Change it as wish
Configure it as the following picture. The wireless parameter is the one of wireless router which
module need to connect.
Shenzhen Hi-Link Electronic Co.,Ltd
Http://www.hlktech.ltd Tel:0755-83575155 Fax:0755-83575189

Kindly note

Disable static IP : Enable DHCP, module gets IP from router.It need to log in
router to find the module IP.
Static IP : 192.168.2.1 Input the IP address and you need to know the IP
address rule of router.For examples: Our router IP segment :
192.168.2.xxx.;255.255.255.0 , 192.168.2.1 ;
Shenzhen Hi-Link Electronic Co.,Ltd
Http://www.hlktech.ltd Tel:0755-83575155 Fax:0755-83575189

5. Restart module
Module will connect named 8E20 router. Then it is working and communicated.

6. PC in Same LAN network segment: ping 192.168.2.110

Then HLK-RM08K module is connected to the wireless router and could do the testing.
Shenzhen Hi-Link Electronic Co.,Ltd
Http://www.hlktech.ltd Tel:0755-83575155 Fax:0755-83575189

It could send and receive data between serial port and PC. Serial port 0 configuration is same as serial
port 1.

You might also like