Scribd
Upload
15 views

lec_week6

Uploaded by

ruvaifainam874
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
15 views

lec_week6

Uploaded by

ruvaifainam874
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 24

Chapter 3

Methods of Analysis
Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.

1
Methods of Analysis - Chapter 3

3.1 Motivation
3.2 Nodal analysis.
3.3 Nodal analysis with voltage sources.
3.4 Mesh analysis.
3.5 Mesh analysis with current sources.
3.6 Nodal and mesh analysis by inspection.
3.7 Nodal versus mesh analysis.

2
3.1 Motivation (1)
If you are given the following circuit, how can
we determine (1) the voltage across each
resistor, (2) current through each resistor. (3)
power generated by each current source, etc.

What are the things which we need to


know in order to determine the answers? 3
3.1 Motivation (2)
Things we need to know in solving any
resistive circuit with current and voltage
sources only:

• Kirchhoff’s Current Laws (KCL)


• Kirchhoff’s Voltage Laws (KVL)
• Ohm’s Law

How should we apply these laws to


determine the answers?
4
3.2 Nodal Analysis (1)
It provides a general procedure for analyzing circuits
using node voltages as the circuit variables.

Example 1

5
3.2 Nodal Analysis (2)
Steps to determine the node voltages:

1. Select a node as the reference node.


2. Assign voltages v1,v2,…,vn-1 to the
remaining n-1 nodes. The voltages are
referenced with respect to the
reference node.
3. Apply KCL to each of the n-1 non-reference
nodes. Use Ohm’s law to express the branch
currents in terms of node voltages.
4. Solve the resulting simultaneous equations
to obtain the unknown node voltages. 6
3.2 Nodal Analysis (3)
Example 2 – circuit independent current source only

Apply KCl at
node 1 and 2 v1 v2

*Refer to in-class illustration, textbook, answer v1 = -2V, v2 = -14V 7


3.2 Nodal Analysis (4)
Example 3 – current with dependant current source

*Refer to in-class illustration, textbook,


answer v1= 4.8V, v2 = 2.4V, v3 = -2.4V 8
3.3 Nodal Analysis with
Voltage Source (1)
Example 4 –circuit with independent voltage source

How to handle the 2V voltage source? 9


3.3 Nodal Analysis with
Voltage Source (2)

A super-node is formed by enclosing a (dependent


or independent) voltage source connected between
two non-reference nodes and any elements
connected in parallel with it.

*Note: We analyze a circuit with super-nodes using


the same three steps mentioned above except that
the super-nodes are treated differently.

10
3.3 Nodal Analysis with
Voltage Source (3)
Basic steps:

1. Take off all voltage sources in super-


nodes and apply KCL to super-nodes.

2. Put voltage sources back to the nodes


and apply KVL to relative loops.

11
3.3 Nodal Analysis with
Voltage Source (4)
Example 5 – circuit with independent voltage source
Super-node => 2-i1-i2-7 = 0

Apply KVL => v1+2-v2 = 0


12
3.3 Nodal Analysis with
Voltage Source (5)
Example 6 – circuit with two independent voltage
sources

13
3.3 Nodal Analysis with
Voltage Source (6)
Example 7 – circuit with two independent voltage
sources

-i1-i2 + i3 = 0 -i3-i5-i4 + i1 = 0 v1-20-v2 = 0 v3-3vx-v4 = 0


14
3.4 Mesh Analysis (1)
1. Mesh analysis provides another general
procedure for analyzing circuits using mesh
currents as the circuit variables.

2. Nodal analysis applies KCL to find unknown


voltages in a given circuit, while mesh analysis
applies KVL to find unknown currents.

3. A mesh is a loop which does not contain any


other loops within it.

15
3.4 Mesh Analysis (2)
Steps to determine the mesh currents:

1. Assign mesh currents i1, i2, …, in to the


n meshes.

2. Apply KCL to each of the n meshes. Use Ohm’s


law to express the voltages in terms of the
mesh currents.

3. Solve the resulting n simultaneous equations


to get the mesh currents.
16
3.4 Mesh Analysis (3)
Example 8 – circuit with independent voltage sources

Note:
i1 and i2 are mesh current (imaginative, not measurable directly)
I1, I2 and I3 are branch current (real, measurable directly)
I1 = i1; I2 = i2; I3 = i1 - i2
17
*Refer to in-class illustration, textbook
3.4 Mesh Analysis (4)
Example 9 – circuit with dependent voltage source

18
*Refer to in-class illustration, textbook, answer Io = 1.5A
3.5 Mesh Analysis with
Current Source (1)
Circuit with current source

A super-mesh results when two meshes have a (dependent or


independent) current source in common as shown in (a). We create
a super-mesh by excluding the current source and any elements
connected in series with it as shown in (b).
19
*Refer to in-class illustration, textbook
3.5 Mesh Analysis with
Current Source (2)
The properties of a super-mesh:

1. The current source in the super-mesh is not


completely ignored; it provides the constraint
equation necessary to solve for the mesh
currents.

2. A super-mesh has no current of its own.

3. A super-mesh requires the application of both


KVL and KCL.

20
3.6 Nodal and Mesh Analysis
with Inspection (1)
The properties of a super-mesh:

1. The current source in the super-mesh is not


completely ignored; it provides the constraint
equation necessary to solve for the mesh
currents.

2. A super-mesh has no current of its own.

3. A super-mesh requires the application of both


KVL and KCL.

21
3.6 Nodal and Mesh Analysis
with Inspection (2)
Example 10 – By inspection, write the nodal voltage equations
for the circuit

22
*Refer to in-class illustration, textbook
3.6 Nodal and Mesh Analysis
with Inspection (3)
Example 11 – By inspection, write the mesh-current equations
for the circuit

23
*Refer to in-class illustration, textbook
3.7 Nodal versus Mesh
Analysis (1)
To select the method that results in the smaller number of
equations. For example:

1. Choose nodal analysis for circuit with fewer nodes than


meshes.
*Choose mesh analysis for circuit with fewer meshes
than nodes.
*Networks that contain many series connected
elements, voltage sources, or supermeshes are
more suitable for mesh analysis.
*Networks with parallel-connected elements, current
sources, or supernodes are more suitable for nodal
analysis.
2. If node voltages are required, it may be expedient to
apply nodal analysis. If branch or mesh currents are
required, it may be better to use mesh analysis. 24

You might also like