4.

1" x 4" threaded shear

stud, already welded by
structural steel fabricator.
8 point pick locations.
1. Dear Oraveen, 3. Pocket will be grouted See detail below and
In order to full fill the suggested in the field by GC with
B lifting requirements by GC, we C advise if acceptable.
proposes the detail ON PAGE approved material. Please
- -
#2, which need to be verified by confirm.
GC/production. 5. (8)-3" DIA x 6"
DJ deep pocket to
2. (8)-3" DIA x 6" #4 J BAR AT 6" SPA.(TYP.)
deep pocket to access threaded
access threaded #4 BAR AT 6" SPA.
LWC PRECAST DECK #4 BAR (TYP.)
studs for lifting.
2'-7" (TYP.) 3" DIA
studs for lifting.

4"
Please confirm

2"
if acceptable.

1'-10"

6"DEEP
> STRINGER

1"
2" (TYP.)

2"
A

#4J BAR @ 10" SPA.

#4 BAR @ 5" SPA.

ANCHOR BOLT FOR OUTLINE OF
RAILING POST HAUNCH BELOW
-- 2
SEE NOTE 1 (TYP.)
(TYP.) SS-0640
7'-8"

STRINGER

841" PSU DECK

1'-2"
(TYP.)
SECTION

SLAB
B

DECK
3" 4" 4" 3"

84"

3'' MIN
183"
-
SCALE: 1"=1'-0" (TYP.)
1

(TYP.)
2"
AA. This is the snap shot taken

1
from Job 24-004 PBU's , we may
> STRINGER provide haunch detail to start at

6" STUD HIGHT

2" HAUNCH
the edge of stringer with a 90 7
8"Ø x 6" SHEAR
STUDS (TYP.)
degree turn instead of 45 degree. C.L. GIRDER
1'-10"

You may confirm with fabrication

ANCHOR BOLT too. 2 DETAIL-2
FOR RAILING SCALE: 1½"=1'-0"
(TYP.) LWC PRECAST DECK
> EXIST.
TRUSS
3'-9" 8'-6"

27'-3ƒ" 1'-6"

6"
3
28'-8 4"(SIDE SPAN) UTLITY CONDUIT
3
28'-10 4" (MAIN SPAN) (TYP.)
> BRACKET AND > BRACKET AND
EXIST. FB EXIST. FB
TANDEMLOK
TO HOOK SPREADER OR
SIMILAR

DIAPHRAGM / UTILITY RAILING

PREFABRICATED BRIDGE UNIT (PBU) 1 - PLAN SUPPORT BEAM HSS4x4x¼ SUPPORT
BEAM
(NORTH SIDE SHOWN, SOUTH SIDE OPPOSITE HAND AND SIMILAR) 3 (TYP.)
SCALE: ½" = 1'-0" 4-WAYS, TYP STRINGER
SS-0640
(TYP.)
1"x4" THREADED
SHEAR STUD W/
SECTION C
-
COUPLING NUT AND SCALE: 1"=1'-0"
2'-0" 2'-0" HR-125 SWIVEL
13" MAX.20"
24" MAX. LIFTING EYE, TYP
MAX. 4'-0"
4'-0"
4'-0"
18" MAX. SHEAR STUD
12" MAX. SPACING
8" MAX.

NOTES:
1. FOR RAILING DETAILS, SEE DRAWING NOS. SR-0601 AND
SR-0602.

> DECK JOINT, 2. FOR CLOSURE POUR AND FIELD SPLICE DETAILS, SEE DRAWING
STRINGER DIAPHRAGM/UTILITY NO. SS-0643.
BRACKET AND 1'-2"
SUPPORT (TYP.)
EXIST. FB
1¼" DIA. HOLE > CLOSURE POUR AND > BRACKET AND 3. PRECAST EDGES ADJACENT TO CLOSURE POUR SHALL PROVIDE A
(B.S.) FIELD SPLICE EXIST. FB 1/4" MINIMUM AMPLITUDE ROUGHENED SURFACE WITH EXPOSED
AGGREGATE AND SHALL BE ABRASIVE BLAST OR HIGH
⅜" = 1'-0" PRESSURED WATER JET CLEANED.
SECTION A

SCALE: - 1 0 1 2 3 4 5 6 7
4. REINFORCING STEEL SHALL MEET THE REQUIREMENTS OF
NYSDOT 709-13 STAINLESS STEEL BAR REINFORCEMENT.
NOTE:SHEAR STUDS NOT SHOWN
FOR CLARITY

IT IS A VIOLATION OF THE PROFESSIONAL LICENSE LAW FOR ANY PERSON TO ALTER THIS DRAWING IN ANY WAY, UNLESS ACTING UNDER THE DIRECTION OF A LICENSED PROFESSIONAL ENGINEER / REGISTERED ARCHITECT. THE ALTERING
ENGINEER/ARCHITECT SHALL AFFIX TO THE DRAWING HIS/HER SEAL AND THE NOTATION "ALTERED BY" FOLLOWED BY HIS/HER SIGNATURE AND THE DATE OF SUCH ALTERATION, AND A SPECIFIC DESCRIPTION OF THE ALTERATION.
CONTRACT RK-19A DRAWN BY G. BAL DATE 08/16/2024
ROBERT F. KENNEDY BRIDGE STRUCTURAL REHABILITATION
OF THE EAST RIVER SUSPENDED SPANS AND ANCHORAGES
DESIGNED BY D. KRUSZEWSKI STRUCTURAL

ERSS PROPOSED DRAWING NO.

CONSTRUCTION S. YIM
PREFABRICATED BRIDGE
CHECKED BY

REVISION DESCRIPTION DATE APPROVED

& DEVELOPMENT SS-0633
REVISIONS UNIT DETAILS - 1 APPROVED BY
REVISION

$FILE$ PRINT AS OF $DATE$ $TIME$ $$user$$

 HR-125 Swivel Hoist
ring assembly with 1" NOTE: THIS DATA
dia x 4" long bolt.
SHEET IS
UNC Swivel Hoist Rings Supplied and installed
by JP. Please confirm. 1" dia x 2 3/4" long DOWNLOADED
threaded coupling nut
supplied and installed FROM INTERNET.
by JP. Please confirm.
1" x 3" long See data sheet below
threaded bolt for coupling nut.
see table below #of Threads
per inch

B=1.14 INCH 1/2” - 13 x 2.25”

SEE BELOW
DATA TABLE Bolt
Diameter

OF SHEAR STUD
ENGAGEMENT
1.14" THREAD

0.5" GAP
Length of Bolt
(from under head)
HR-125 1" x 4" threaded Medium/Heavy Forming

Swivel Hoist Ring shear stud,

D4 Hex Coupling Nut
already welded Dayton Superior D4 Hex Coupling Nuts are used to splice D1 Inside Tie National
D4 Hex Coupling Nut Selection Chart
Safe Working
Rods. Threads are right hand national course and will accept standard Course A B C Load Tension
by structural steel machine bolts. In order to develop the rated load you must make certain
that you have equal engagement of the inside threaded rods or bolts.
Thread Dia.
3/8" 1-3/4" 5/8" 11/16"
(lbs.)
3,750

fabricator. 8 point Hex coupling nut is not provided with a center stop. 1/2"
5/8"
1-3/4"
2-1/8"
11/16"
13/16"
3/4"
1-5/16"
9,000
12,000

pick locations. 3/4" 2-1/4" 1" 1-1/8" 18,000

• Top washer has the following features: Typical Stringer C 1" 2-3/4" 1-3/8" 1-9/16" 36,000

SWL provides a factor of safety of approximately 2 to 1.

• The Working Load Limit and Recommended Torque value are permanently stamped into each washer. B A
To Order:
Specify: (1) quantity, (2) name, (3) thread diameter.

• Washer is color coded for easy identification: Red - UNC thread. PROPOSED LIFTING
Example:
2,000 pcs. D4 Hex Coupling Nuts, 1/2" thread.
D4 Hex Coupling Nut

• Individually Proof Tested to 2-1/2 times Working Load Limit. DETAIL

• Bolt specification is an Alloy socket head cap screw to ASTM A 574. BASED ON GC'S

Accessories
• All threads listed are UNC.

Rigging
SUGGESTION
• BOLT SIZE IDENTIFICATION: The size of the bolt will be stated as in the drawing above. Illustration shows meaning of each dimension given.
• NOTE: For Special Applications, see page 457.
• Frame 2 and larger are RFID EQUIPPED.

®
SEE APPLICATION AND
WARNING INFORMATION
On Pages 210 - 211
Para Español: www.thecrosbygroup.com

HR-125 UNC Threads

Dimensions
(in.)
Effective
Working Thread
Frame Load Torque Projection Weight
Size HR-125 Limit in Bolt Size Length Radius Diameter Each
No. Stock No. (lbs.)* Ft. Lbs. A‡ B C D E F G H (lbs.)
1† 1016887 800 7 5/16 - 18 x 1.50 .58 2.72 .97 .46 .34 1.87 1.12 .37
1† 1016898 1000 12 3/8 - 16 x 1.50 .58 2.72 .97 .46 .34 1.87 1.05 .39
2 1016909 2500 28 1/2 - 13 x 2.00 .70 4.85 1.96 .87 .75 3.35 2.29 2.33
2† 1016912 2500 28 1/2 - 13 x 2.50 1.20 4.85 1.96 .87 .75 3.35 2.29 2.36
2 1016920 4000 60 5/8 - 11 x 2.00 .70 4.85 1.96 .87 .75 3.35 2.16 2.41
2† 1016924 4000 60 5/8 - 11 x 2.75 1.45 4.85 1.96 .87 .75 3.35 2.16 2.47
2 1016931 5000 100 3/4 - 10 x 2.25 .95 4.85 1.96 .87 .75 3.35 2.04 2.52
2† 1016935 5000 100 3/4 - 10 x 2.75 1.45 4.85 1.96 .87 .75 3.35 2.04 2.59
3 1016942 7000 ** 100 3/4 - 10 x 2.75 .89 6.57 2.96 1.36 .94 4.87 2.97 6.72
3† 1016946 7000 ** 100 3/4 - 10 x 3.50 1.64 6.57 2.96 1.36 .94 4.87 2.97 6.81
3 1016953 8000 160 7/8 - 9 x 2.75 .89 6.57 2.96 1.36 .94 4.87 2.84 6.84
3† 1016957 8000 160 7/8 - 9 x 3.50 1.64 6.57 2.96 1.36 .94 4.87 2.84 6.96
3 1016964 10000 230 1 - 8 x 3.00 1.14 6.57 2.96 1.36 .94 4.87 2.72 7.09
3† 1016969 10000 230 1 - 8 x 4.00 2.14 6.57 2.96 1.36 .94 4.87 2.72 7.31
4 1016975 15000 470 1-1/4 - 7 x 4.50 2.21 8.72 3.71 1.75 1.19 6.18 3.93 14.51
5 1016986 24000 800 1-1/2 - 6 x 6.75 3.00 12.55 4.71 2.39 1.75 8.48 5.52 37.73
5 1016997 30000 1100 2 - 4-1/2 x 6.75 3.00 12.55 4.71 2.39 1.75 8.48 5.02 40.69
6 1017001 50000 2100 2-1/2 - 4 x 8.0 4.00 16.88 5.75 3.00 2.25 11.00 8.03 88.00
7 1017005 75000 4300 3 - 4 x 10.5 5.00 19.50 6.45 3.75 2.75 14.16 8.50 166.00
8 1017009 100000 5100 3-1/2 - 4 x 13.0 # 7.00 22.09 7.75 4.00 3.25 15.91 9.28 265.00
*Ultimate Load is 5 times the Working Load Limit.
** Ultimate Load is 4.5 times the Working Load Limit for 7000# Hoist Ring when tested in 90 degree orientation.
† Long Bolts are designed to be used with soft metal (i.e., aluminum) workpiece. While the long bolts may also be used with ferrous metal (i.e.,steel & iron) workpiece, short bolts are designed for
ferrous workpieces only.
‡ Bolt specification is an Alloy socket head cap screw to ASTM A 574.
# Hex head bolt used on Frame 8 (100,000lb.) Hoist Ring.
 Medium/Heavy Forming

D4 Hex Coupling Nut D4 Hex Coupling Nut Selection Chart

Dayton Superior D4 Hex Coupling Nuts are used to splice D1 Inside Tie National Safe Working
Rods. Threads are right hand national course and will accept standard Course A B C Load Tension
Thread Dia. (lbs.)
machine bolts. In order to develop the rated load you must make certain
that you have equal engagement of the inside threaded rods or bolts. 3/8" 1-3/4" 5/8" 11/16" 3,750
Hex coupling nut is not provided with a center stop. 1/2" 1-3/4" 11/16" 3/4" 9,000
5/8" 2-1/8" 13/16" 1-5/16" 12,000
3/4" 2-1/4" 1" 1-1/8" 18,000

C 1" 2-3/4" 1-3/8" 1-9/16" 36,000

SWL provides a factor of safety of approximately 2 to 1.

To Order:
Specify: (1) quantity, (2) name, (3) thread diameter.
B A
Example:
2,000 pcs. D4 Hex Coupling Nuts, 1/2" thread.
D4 Hex Coupling Nut

See D6 Nut Washer information with B27

Medium/Heavy Forming Products

D9 Taper Ties
Dayton Superior D9 Taper Ties are used where spec- B39
B39 WingNut
Wing Nut
ifications require or permit complete removal of the B39
B39 Wing Nut
form tie from the concrete. Standard taper ties are Wing Nut
Studs
Studs
supplied with coil thread in the diameters and lengths
shown in the chart. Other lengths are available on
special order.
A complete taper tie assembly consists of one taper
tie, two flat washers and two appropriate nut devices. B11 WWales
ales
B11 Flat
Standard taper ties are manufactured with a taper FlatW asher
Washer
WWall
allThi ckness
Thickness
up to 30" in length. Longer tapers are available on
special order.
To Order:
For wrench turning purposes, taper ties are manufactured with a square end. Specify: (1) quantity, (2) name, (3) diameter,
On the opposite end (smaller end) is designed with a protruding nose to prevent large and small, (4) O.A. length.
thread damage during the removal operation. Coating the taper tie with waterproof
grease will facilitate taper tie removal. Example:
Note: Taper ties will wear and get damaged. They must be continually inspected 250 pcs. D9 Taper Ties, 1-1/4" dia. to 1" dia., 54"
and replaced if wear or damage is noted. O.A. length.

D9 Taper Ties Selection Chart

Safe Working Load Large End of Tie Small End of Tie
Tension Standard Tie Tapered Body
Coil Thread Length of Coil Thread Length of Lengths Diameter
(lbs.) Diameter Thread Diameter Thread
7,500 3/4" 10" 1/2" 2" 34", 43", 52" .670" to .500"
18,000 1" 10" 3/4" 6" .884" to .750"
30", 36", 42", 48",
34,000 1-1/4" 10" 1" 6" 1.113" to 1.00"
54", 60", 72"
50,000 1-1/2" 10" 1-1/4" 6" 1-1/2" to 1-1/4"
75,000 H.S. 1-3/4" 10" 1-1/2" 6" 36", 48", 60", 72" 1-3/4" to 1-1/2"

SWL provides a factor of safety of approximately 2 to 1.

04/19 65