J5 CHASSIS / TELEVISION

J5 CHASSİS / TELEVİSİON

SERVICE MANUAL

September 2012 1
 J5 CHASSIS / TELEVISION

1. REVISION LIST .................................................................................................................... 5

2. SAFETY WARNINGS .......................................................................................................... 6
3. PRODUCT SPECIFICATIONS ............................................................................................ 7
3.1. Technical Specifications ................................................................................................. 7
3.2. Functional Features ......................................................................................................... 8
3.3. Special Features ............................................................................................................. 10
3.3.1. Smart Inter@ctive TV 2.0 (GRUNDIG SMART APPS) internet applications .... 10
3.3.6. DLNA (Home Network) ........................................................................................ 13
3.3.7. HBB TV (Hybrid Broadcast Broadband TV) ........................................................ 13
3.3.8. 3D TV (3-Dimension TV Technology) .................................................................. 13
3.3.9. DVB-S2 .................................................................................................................. 14
3.3.10. DVB-T2 ................................................................................................................ 14
3.3.9. USB Recording (USB-PVR) .................................................................................. 15
3.3.12. DIGI LINK and HDMI CEC Feature ................................................................... 16
3.3.13. Operation with Common Interface (CI+) ............................................................. 16
3.3.14. DIVX VOD ACTIVATION......................................................................................... 16
3.3.15. Passive 3D (FPR) Feature ........................................................................................ 18
3.3.16. Wired / Wireless keyboard and mouse support ........................................................ 18
3.3.17. Dual Gaming ............................................................................................................ 19
4.1. Product Installation ....................................................................................................... 20
4.2. Input/Output Connections ............................................................................................. 22
4.3. Remote Control ............................................................................................................. 24
4.3.1. GRUNDIG 3D Remote Control (TP7)................................................................... 24
4.3.2. GRUNDIG 3D Remote Control (TP8/TP9) ........................................................... 25
5. USING NEW PRODUCT FEATURES ............................................................................... 26
5.1. Digital Satellite Settings and Setup (DVB-S2) ............................................................. 26
5.1.1. Easy Installation ..................................................................................................... 26
5.1.2. Advanced Installation ............................................................................................. 26
5.1.3. Digital Satellite Channel Settings .......................................................................... 27
5.1.4. LNB Settings .......................................................................................................... 29
5.2. 3D Function ................................................................................................................... 30
5.2.1. 3D Picture Viewing ................................................................................................ 30
5.2.2. 3D Picture Settings ................................................................................................. 31
5.2.3. Adjusting 2D>3D Effects ....................................................................................... 31
5.2.4. Left-Right Correction ............................................................................................. 31
5.2.5. Formats supported with HDMI 1.4 ........................................................................ 31

September 2012 2
 J5 CHASSIS / TELEVISION

5.2.6. Dual Gaming Feature ............................................................................................. 32

5.3. Inter@ctive TV and Home Network ............................................................................. 32
5.3.2. Wired Network Settings ......................................................................................... 33
5.3.3.Auto Connection ..................................................................................................... 33
5.3.4. Manual Connection ................................................................................................ 33
5.3.5. Wireless Network Connection ............................................................................... 34
5.3.6. Wireless Network Settings ..................................................................................... 35
5.3.7. Auto Wireless Network Connection ...................................................................... 35
5.3.8. Manual Wireless Network Connection .................................................................. 36
5.4. Smart Inter@ctive TV 2.0 Internet Applications .......................................................... 36
5.4.1. Starting with Smart Inter@ctive TV ...................................................................... 37
5.4.1.1. Creating a Grundig Smart Apps account ............................................................. 38
5.4.1.3. Selecting internet applications ............................................................................ 39
5.4.1.4 Grundig Appstore ................................................................................................ 39
5.4.3. Selecting and Installing the BABYCAM application ............................................ 42
5.4.3.1 BABYCAM network installation ........................................................................ 42
5.5.4. GRUNDIG voice controlled remote - installation ..................................................... 44
5.5. DLNA Home Network Connection............................................................................... 47
5.5.1. Selecting Digital Media Server .............................................................................. 47
5.6. USB Functions .............................................................................................................. 48
5.6.1. Recording TV Programmes (PVR) ........................................................................ 48
5.6.2. Time Shift – Pause Programme .............................................................................. 49
5.7. USB Mode ................................................................................................................. 49
5.7.1. Connecting External Data Storage Devices ........................................................... 50
5.9. DIGILINK & CEC Feature ........................................................................................... 51
6. EXTERNAL DEVICE CONNECTION .............................................................................. 52
7. GENERAL OPERATING PRINCIPLE OF TV .................................................................. 55
7.1. Chassis General Operating Principle............................................................................. 56
7.2. DC Power Stage ............................................................................................................ 57
8. OPERATING PRINCIPLES OF CIRCUIT COMPONENTS............................................. 59
8.1. Circuit components on the chassis ................................................................................ 59
9. SERVICE MENU SETTINGS……………………………………………………………………..77

10. CUSTOMER SETTINGS…………………………………………………………………………90

11.FAILURE ANALYSES ...................................................................................................... 94

11.1. Sound but no picture, and backlight illuminated......................................................... 94
11.2. Sound but no picture, and backlight not illuminated .................................................. 95

September 2012 3
 J5 CHASSIS / TELEVISION

11.3.No Sound ...................................................................................................................... 95

13. CHASSIS SCHEMATIC ................................................................................................... 97
14.5. TeraTerm Setup ............................................................................................................. 118
15.1.PC-DVI Resolution Info............................................................................................. 121
15.2. HDMI-H PC Resolution Info .................................................................................... 121
15.3. HDMI-H YPbPr Resolution Info .............................................................................. 122
16. HOTEL TV SETUP ......................................................................................................... 123
17. J5 CHASSIS DIGITURK ENABLED TV SETUP………………………………..……125
17.1.Television setup.......................................................................................................... 125
18. FINDING MISSING CHANNELS ON PRODUCTS WITH SATELLITE RECEIVER130

September 2012 4
 J5 CHASSIS / TELEVISION

1. REVISION LIST

Revision List
Item No Version Revision Date Responsible
1 0 SEK draft published 27.08.2012 TV Design Application
Some features of the product are now
optional.
2 1 Service menu settings are updated 22.01.2013 TV Design Application
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44

September 2012 5
 J5 CHASSIS / TELEVISION

2. SAFETY WARNINGS

Panels used in LED panel televisions are quite sensitive in electrical and physical aspects.
Therefore, the following warnings should be observed.

1. Panel surface is quite sensitive and can be damaged easily. Take care to avoid scratches
on the panel surface. When you need to lay down the panel, place it on a floor, which will not
cause damages. Besides, do not use rough materials when touching or wiping the panel
clean.

2. Keep panel surface clean. Put on rubber gloves when touching panel surface. To clean
the surface, use a mild cleaning agent that does not get electrified.

3. Keep LED module away from water. Spilling water in or on the panel causes electrical
damage. It should be wiped dry, if needed.

4. Avoid sudden temperature and humidity changes. Sudden changes of temperature and
humidity may harm the panel.

5. High temperature and humidity shortens product life. LED panels are not suitable for use
under high temperatures and humidity conditions. The user should observe the specified
temperature and humidity values.

6. Keep it away from harmful (corrosive) gases. Corrosive gases damage chemical and
electronic structure of LED panel.

7. Static electricity flow may damage the panel. LED module contain materials sensitive to
static electricity such as CMOS, etc. The body should be grounded before touching the
panel. Also, you must not touch connector areas with bare hands.

8. The same image should not stay on the screen for prolonged times. Keeping the same
image on the screen for a long time may lead image retention and the panel may get
damaged. Therefore, TV should be turned off when not in use and the image should be
changed within certain intervals when displaying still images.

September 2012 6
 J5 CHASSIS / TELEVISION

3. PRODUCT SPECIFICATIONS

3.1. Technical Specifications

Screen size 32"-37"-42”-47”-55" LED TV

Full HD 100Hz -
Full HD TM 200Hz (3D) TM100HZ 32" 37" 42" 47" 55"
Passive 3D 32" 37" 42" 47" 55"
Sound output 2x10Watt / 55”:2x15W
Onboard Subwoofer 1X10W @ 8 ohm (optional)
Standby power consumption <0.5W
Rosh Limits Pb (Lead) / Hg (mercury) Pb complies with RoHS directive / 0 mg
Scart input Standard
Audio/Video RCA input Standard
S-Video input Standard
HDMI input 1-2-3-4 Standard
YPBPR input Standard
VGA input Standard
PC audio input Standard
Line Out Standard
Headphone Output Standard
USB input (USB 2.0) + Recording feature Standard
CI Slot input (CI+) Standard
Optic Out Standard
DVB T/C Standard
DVB S2 Optional
DISEQC Diseqc 1.2
DVB T2 Optional
HDMI 1.4 Standard
HDMI CEC Standard
CI+ Standard
MPEG4 Standard
Studio Sound /HD
SRS
Truvolume/Dialog
Dolby Dig. 2+1/ 5+1 Standard
Div X HD + Standard
Appstore (download-remove-update, move, add
favorite) Standard
Skype Ready Plug into Skype (Standard - applications)
W8, Iphone/ipad, Android remote control Standard
MEGA DCR Optional
MEMC Standard
USB PVR Standard
HOTEL TV Optional (Basic)
WI-FI (Internal) Optional
ETHERNET Standard
WEB Standard
Internet Applications (Optional) GRUNDIG SMART APPS
DLNA Standard
Power input (V/Hz.) 220-240V ~ 50-60 Hz
1500 (Cable-DVB-C/C2) / 100 (analog) /1500 (Terrestrial DVB-
Digital Program memory TV/Radio T/T2) / 100 (analog) / 6000 (DVB-S/S2)
Sound systems Mono / Stereo / Nicam
Analog: Depends on the country/region selection: B/G, D/K, I, L
Picture systems Digital :DVB-T/T2, DVB-C, DVB -S2
Antenna / Cable UHF / VHF / 75 ohm
Cable: Full band 110MHz 862MHz Modulation: 16QAM,
32QAM,64QAM, 128QAM and 256QAM Symbol rate:
4.0Msym/s to 7.2 Msym/s
Terrestrial: VHF/UHF Bandwidth 177.5-858.0MHz, Channel
Reception range
Bandwidth: 7 MHz and 8 MHz
COFDM modes: 2k and 8k Set: 16QAM, 64QAM, QPSK 8k Set:
16QAM, 64QAM, QPSK
Analog: C02 ... C80, special channels S01 ... S41

September 2012 7
 J5 CHASSIS / TELEVISION

Satellite: Band range 950 MHz to 2150 MHz , QPSK, 8PSK

Demodulation, Symbol rate; 1 to 45 Msps for DVBS
and 5 to 30 Msps for DVBS2.
.mp3, .m4a, .aac, .mov, divx (4/5/6.x), .mpg, .vob, .dat, .ts, .avi,
.mp4, .mkv.
USB Film formats In addition to video data, these files also contain audio data
compressed and "packaged" by using MP3, AAC or Dolby
Digital©.
PVR to USB recording feature for a channel while
watching the other channel out of 2 channels at the
same transponder frequency (DVB-T, DVB-S) Standard
USB Subtitle formats SRT, SSA, ASS, SMI
USB Image formats .jpg, .jpe, .bmp, .png, .gif,

3.2. Functional Features

J5 chassis project is designed as the continuation of TP connected TV concept, and it is

intended to be more comprehensive than previous products as of the features provided with
the extra features added to available supported features. It is planned to use 32” 37” 42” 47”
and 55” passive 3D LED panels with the available AIR cabinets in the project.

Grundig Smart Apps application market shall also be activated by the introduction of J5
project. All applications included in this market shall be easily downloaded/removed to/from
TV via internet; and video conferencing feature with Plug into Skype, also available with an
application; and recording to USB of a channel while watching the other one of 2 different
channels with the same transponder frequency in DVB-T / DVB-S broadcasts shall also be
introduced.

Besides these features, J5 chassis supports both analog and digital broadcasts. As is known,
digital broadcasts are divided in three as terrestrial digital broadcasting (DVB-T/DVB-T2:
Digital video Broadcasting Terrestrial), cable digital broadcasting (DVB-C: Digital video
broadcasting cable) and digital satellite broadcasting (DVB-S2: Digital video broadcasting
satellite). Our J5-chassis televisions support DVB-T/C, DVB-T2 (optional) and DVB-S2
(optional) broadcasting. Digital receiver unit of the product processes signals coming from
digital transmitters and convert them into audio and video of superior quality. It enables you
to access video, music and photo file and play those media.

Supporting all systems of analog broadcasting (multisystem), J5 chassis has image

improvement algorithms such as 3D comb filter, 3D deinterlacer, DLTI and DCTI features.
DNR (digital noise reduction) and MPEGNR (MPEG noise reduction) improvements have
been used to lessen noise. Moreover, it features sound improvement algorithms Studio
Sound /HD and Truvolume/Dialog audio systems; supports AC3 (Dolby digital), AC3+ (Dolby
digital plus) , AAC and HE-AAC coded audio broadcasts in digital broadcasting.
To summarize, J5-chassis products support the following features.

• Features supported with TP-chassis

• Appstore
• Passive and active 3D support
• A level compatibility with Eup criteria
• DLNA DMP-DMR support
• Wired / Wireless internet connection support
• 3D Full HD play/record support
• 2D/3D conversion support
• Onboard Subwoofer support

September 2012 8
 J5 CHASSIS / TELEVISION

• Skype compliant
• Embedded 2 x Wi-Fi adaptor support
• TP7-TP8-TP9,YF1/YF2; iphone/ipad RC, Android RC; voice control app/RC
• Unicable solution in DVB broadcasts
• Availability of using different sources during recording (other than tuner)
• Animation assisted Shop mode
• Support for SRS Studio sound HD and Truvolume/Dialog audio systems.
• Subwoofer
• Voice controlled remote (motion control is also available.)
• Analog Output (Line-out)
• Baby Watch (Can be operated via applications)
• Permanent recording (optional)
• Dolby 2+1/5+1
• PVR to USB recording feature for a channel while watching the other channel out of 2
channels at the same transponder frequency in DVB-C or DVB-T / DVB-S broadcasts
• Product system software update through on-air broadcasting or via internet.
• Panel lock
• Picture freezing and zoom
• Wired / Wireless keyboard and mouse support
• Dual Gaming (two people playing a game on the same screen)

September 2012 9
 J5 CHASSIS / TELEVISION

3.3. Special Features

3.3.1. Smart Inter@ctive TV 2.0 (GRUNDIG SMART APPS) internet applications

Smart Inter@ctive TV 2.0 interactive applications

provides internet services and pages on your TV.
These applications are designed according to your
television. Through Smart Inter@ctive TV 2.0 feature
you can run many local and global internet applications.
Grundig Appstore allows you to obtain various
applications you may use with your Grundig TV. From
Grundig Appstore,
you may download many applications. These
applications include:
video and audio chat, video, picture and music
applications, social networks, news and sports
applications, weather forecast application and doctor or
pharmacy search, recipe viewing and viewing traffic
congestions depending on your local city.
You need to be registered to access all applications in
Grundig Smart Apps.

Grundig Appstore

Grundig Appstore is an online store where applications that will be used on the TV can be
downloaded.
Some applications on ≫
SMART inter@ctive TV≪ menu are installed on your TV by the factory.
You may download many applications from wide application choices in the Grundig Appstore.

Internet applications will optionally vary according to the region and country. Some optional
and standart internet applications are: Plugged into SKYPE, YouTube, İBB Tafik, Reuters,
TwitTALK, Facebook, Yemeksepeti, Ebay, Picasa, Flickr, BonGusto, YogaMour,
AutoMotorSport, Apotheken.de, Arztsuche.de, Bild.de, Funspot, Goal724, HRS, Laufen.de,
Mackolik, NTVmsnbc, NTVSpor, Viewster, BabyCam, WorldWeatherOnline, trip advisior,
Garanti, etc… Inter@ctive TV applications can be accessed by cable or wireless connection.

September 2012 10
 J5 CHASSIS / TELEVISION

3.3.2. SKYPE

An internet connection and the GRUNDIG

G-VCAM-01 USB Camera and
microphone unit that you may purchase
only are required for this. Launch plugged
into Skype application from the GRUNDIG
SMART APPS interactive menu, use your
account or create a new Skype account
With the Plugged Into Skype feature you from your TV. Contact the dealership you
can make audio and video calls from have purchased your TV for purchasing
Skype to Skype with your friends or family information on camera and microphone
anywhere on the world via internet unit.
connection free of charge in the comfort of
your living room.

September 2012 11
 J5 CHASSIS / TELEVISION

3.3.3. BABYCAM

Baby Watch application

Baby Watch application allows you to

monitor your children. An internet
connection and the GRUNDIG G-BCAM-
01 Camera and microphone unit that you
may purchase only are required for this.
Contact the dealership you have
purchased your TV for purchasing
information on camera and microphone
unit.
For more information on the camera and
installation, refer to GRUNDIG G-BCAM-
01 user manual or SEK BabyWatch
installation section.

NOTE: Baby Watch application can be launched through “Quick Apps” menu regardless of
the internet connection on your TV.

3.3.4. Arçelik TV Remote application on smart phones

Your TV supports remote control

application for Apple iPhones and Android
smart phones.
You can download ARCELIK TV Remote
application to your phone free of charge
from Apple App Store or Google Play
depending on the specifications of your
phone and control your TV with your
phone. Your smart phone and TV must be
connected to the same network in order to
use this feature.

As an alternative to the remote control

3.3.5. GRUNDIG Voice Controlled supplied with your TV, you may control
Remote your TV with the GRUNDIG "Voice
Controlled Remote". You may use your TV
with simple voice commands. Contact the
dealer you have purchased your TV for
detailed purchasing information on the
GRUNDIG "Voice Controlled Remote".
You can find detailed information on the
installation of voice controlled remote in
the "Grundig Voice Controlled Remote
Installation" section.

September 2012 12
 J5 CHASSIS / TELEVISION

3.3.6. DLNA (Home Network)

Digital Living Network Alliance (DLNA) is an association established

by the leading companies of consumer electronics, mobile devices
and PC industries. Its objective is to ensure that all electronic
devices which are manufactured by different companies and used
in the home networksare manufactured within certain standards
and comply with each other. Thus, the users can benefit from their
different brand devices in home network smoothly and without interruption. The alliance
companies can develop their products in line with these standards or make desired changes.

With DLNA menu of your television, you can easily access Video, music and photo files on
server; and thanks to DMR feature, you can automatically start and stop media playing on
devices with DMC feature. You can share your video, music and image files through devices
such as PC, mobile phone or NAS (Network Attached Storage) that function as DMS (Digital
Media Server) compatible with DLNA.

3.3.7. HBB TV (Hybrid Broadcast Broadband TV)

Hbb TV (Hybrid Broadcast Broadband TV) includes hybrid,

integrated broadcasting and internet TV. Hbb TV allows the
broadcasters to share internet applications of desired contents
(Weather forecast, EPG, video sharing…) with the user over
internet. HbbTV provides the new generation interactive teletext
broadcast with its modern structure, content and high definition (HD) images and videos.
Your TV should be connected to internet in order to receive the HbbTV broadcast. This new
service is already being provided by ARDV and what's more, via third channel of ZDF. This
service provided by ARD includes a detailed program summary besides the graphically re-
engineered teletext with high definition images and “Das Erste Mediathek”. ZDF’s service
includes “ZDF mediathek” and other program information (as of July 2012). This feature can
only be used in countries where the service is provided.
Although the Hbb TV application is a standard feature in J5-chassis products, Hbb TV is not
currently a feature supported by the broadcasters in our country.

3.3.8. 3D TV (3-Dimension TV Technology)

Passive 3D feature shall be provided as

standard for all panel dimensions in J5-
chassis products. While watching 3D
movies, new generation passive glasses
are used to provide 3D impression like in
movie theaters. Images are recorded at
high resolution and played at high speeds
individually for both eyes. Special

September 2012 13
 J5 CHASSIS / TELEVISION

3D glasses are scheduled to open right and left lenses and synchronize alternating images.
Thus, they avoid quality losses that may occur in traditional 3D images; and you will
experience exciting 3D viewing experience in the comfort of your home.

3.3.9. DVB-S2
In our J5-chassis products, satellite dish input is integrated
(there is not any separate satellite module) to the chassis.
Thus, you can watch satellite broadcasting directly from TV
without any satellite receiver box.
DVB-S (Digital Video Broadcast - Satellite) is satellite
broadcasting received via dish antenna we have been using for years. DVB-S2 technology
also delivers HD broadcasting from satellite in J5-chassis products. So, our TV also functions
as an HD satellite receiver. Scrambled satellite broadcast can also be watched by means of
relevant CI cards.

J5-chassis products will support the satellites Astra-Hotbird-Turksat-Eutelsat-Thor.

3.3.10. DVB-T2
DVB-T stands for Digital Video Broadcasting-Terrestrial. The
frequencies used for DVB-T are UHF and VHF channels that we
are familiar from analog broadcasting. With digital broadcasting,
these channels are used more efficiently compared to analog
technique. Thus, many television channels are accommodated in one frequency. With
COFDM modulation, the bandwidth can be divided among thousands of single carrier. Each
single carrier is encoded with specified technique of QPSK, 16-QAM or 64-QAM modulation.
According to the defined parameters, data rate per channel is approximately 12 to 20 Mbit/s.
Data rate of a frequency can be divided among maximum four programmes. Each divided
programme has averagely 3-5 Mbit/s bit rate. (COFDM)

Operating much more productively than currently used DVB-T technology, DVB-T2 offers the
most appropriate environment for HD broadcasts by using MPEG4 compression technique.
Started to be used in the UK, DVB-T2 technology will also be put into practice by Finland and
Serbia soon. Besides, DVB-T2 is expected to be deployed in many European countries,
primarily Italy and Spain. In our country, TRT has started DVB-T2 test broadcasting in
Dikmen, Ankara.

3.3.11. SCR (Single Channel Router) Technology

J5-chassis products support SCR (Single Channel Router) feature.

The fact that the number of channels which can be received from satellite is very high and
therefore the bandwidth of the signals is very wide makes carrying these signals from the
satellite dish to the house difficult. In addition to that, the increased use of digital video
recording (DVR) devices complicates this problem more. For example, signals received with
four polarities as vertical/horizontal, lower/upper band are controlled by commands from the
device to the LNB and broadcasts with selected polarities are sent only. However, it is not
possible to watch a broadcast while the user is recording a broadcast (DVR) with the same
polarity. In this case, it is required to lay more than one cable from the dish to the house, and
this causes a complicated installation and difficulty in the use of system.

September 2012 14
 J5 CHASSIS / TELEVISION

SCR (Single Channel Router) technology provides a "single cable" solution for the difficulties
described above. Multi-cable situation that is required
by double tuner STB receivers with PVR and for the
distribution of signals to multiple receivers can be
solved by a “single cable” with this system.

SCR (Single Channel Router) system is an integrated

solution that includes software and hardware aspects.
SCR LNB should be used with TVs, satellite receivers
or digital recorders compliant with this system. This
feature is provided by software in the device that the
LNB shall be connected, and there is no need to make
a modification in the hardware of the device.

3.3.9. USB Recording (USB-PVR)

This feature allows you to record digital television
channels (DVB–T / T2, DVB–C and DVB-S2) on an
external USB disk and later play these records over the
disk. Recording programmes to view them later can
only be done with digital television stations (DVB-T/T2,
DVB-C and DVB-S2). You can record and playback
external digital television stations (DVB-T and DVB-C)
according to broadcasting station. Recording and
playing programmes, as well as TimeShift function can
only be carried out by using an external data medium
(hard drive or USB stick). The data medium must have
a capacity of at least 2 GB.
- With the introduction of J5-chassis, it is possible for
the first time to record a channel to USB-PVR or to a
hard disk simultaneously while watching the other
channel out of 2 channels at the same transponder
frequency in DVB-C, DVB-T, DVB-S broadcasts. Also,
it is possible to change the source from USB or DLNA sources without interrupting the record
while recording.

Switching to permanent recording; When the permanent recording option is turned on,
your TV records the channel you are watching to time shift memory. Average recording time
of the memory is 60 minutes.

September 2012 15
 J5 CHASSIS / TELEVISION

- You can pause and restart or rewind or forward the record whenever you want.
- You can follow the live broadcast max. 60 minutes delayed, and you can rewind of
forward the record at this period.

3.3.12. DIGI LINK and HDMI CEC Feature

Our products with J5 chassis are equipped with HDMI CEC feature.
This feature utilizes CEC (Consumer Electronics Control) protocol. CEC
allows you to make an HDMI connection between your TV and DVD
player, satellite receiver or video recorder and control such equipment
with the remote control of the television. This feature must also be
supported by the device you connect. You television supports the following functions.
Your television is equipped with DIGI LINK feature. This feature utilizes CEC (Consumer
Electronics Control) protocol. CEC allows you to make an HDMI connection between your TV
and DVD player, STB or video recorder and control such equipments with the remote control
of the television. This feature must also be supported by the device you will connect.

3.3.13. Operation with Common Interface (CI+)

Common Interface (CI) is only used in DVB receivers. Scrambled channels can only be
viewed with a CA module suitable for the encoding system and the corresponding smart
card. The television set is equipped with a Common Interface slot into which CA modules
from various providers can be inserted. The service provider’s smart card must be inserted in
the CA module to enable the scrambled channels you want to view.

3.3.14. DIVX VOD ACTIVATION

Your TV must be registered in order to play the movies purchased from DivX website. For
this, you can find the registration code of your TV by following the instructions below:

• Select USB source;

September 2012 16
 J5 CHASSIS / TELEVISION

• Select DivX VOD from "Source Setting" menu

• Enter the registration code displayed on the screen to DivX website by following the
instructions provided in the user manual.
•

September 2012 17
 J5 CHASSIS / TELEVISION

• Registration code entered to the website may be changed in some cases (e.g. when
the movie is hired for a time period); therefore, you should check whether the code
has been changed by following the same steps before downloading a new movie
from DivX website.

3.3.15. Passive 3D (FPR) Feature

Passive 3D (FPR) feature shall be supported in all J5-chassis products with AIR cabinet. In
Passive 3D technology, an extra filter (FPR) is available on the filter with respect to active
system and Active shutter 3D glasses that are used previously with batteries and by
recharging are replaced by passive 3D (FPR) glasses without batteries that do not require
recharging.

In Passive 3D technology, special filters are used in TV and 3D glasses and there is no
communication between the 3D glass and TV as it is in the active shutter 3D technology
available; moreover, 3D passive glasses do not require batteries or recharging. 3D FPR
glass takes two frames, one for the left eye and one for the right eye, and send these frames
to brain. 3D perception is provided with these special filters and an uniterrupted perception of
3D is obtained in FPR glasses without the limitations of batteries or recharging. Passive 3D
glasses with the following codes shall be used in passive 3D products VWY910 (DN1109)
and VTY910 (DC1008).

The Passive 3D feature used in TP products with AIR cabinet and the Active shutter 3D
feature used in products with Hermes cabinet are different features and cannot be
interchanged for purposes such as spare parts etc.

3.3.16. Wired / Wireless keyboard and mouse support

Wireless keyboard and mouse support on the Web browser application of your TV provides
convenience to the user while browsing the internet.

September 2012 18
 J5 CHASSIS / TELEVISION

3.3.17. Dual Gaming

Dual Gaming feature allows playing multi-player games that support split screen
feature in full screen mode. This feature supports two players and the players are
required to use dual gaming glasses.

September 2012 19
 J5 CHASSIS / TELEVISION

4. PRODUCT INSTALLATION

4.1. Product Installation

1 For digital satellite stations (DVB-S), plug the cable of satellite dish into »SATELLITE«
socket on the television set; and / or

2a For terrestrial digital stations (DVB-T), plug the cable of the rooftop or indoor antenna
(passive or active indoor antenna with its own power supply) into »ANT IN« socket on the
television set; or

2b For digital stations of the cable TV network (DVB-C), plug the antenna cable into »ANT
IN« socket on the television set; or

2c For analogue stations, plug the antenna cable into »ANT IN« socket on the television set.

3 Plug the power cable into the wall socket.

September 2012 20
 J5 CHASSIS / TELEVISION

Only the AC power cable supplied with the product shall be used. Connect the product to
only mains lines between 220-240 V ~ 50-60 Hz voltage/supply range. SCART, HDMI, VGA
and RCA cables do not come with the device.

It is important to observe the following precautions during installation. To ensure adequate

ventilation, please leave a clearance of at least 10 cm at all sides of the product. Do not
place the product on surfaces such as a bed, couch, pillows, etc. and do not block the
ventilation openings.

Do not leave the product under direct sunlight or near a heat source. Avoid using the product
under ambient temperatures out of 0 °C - 40 °C rang e.
Do not use it in areas close to bathtub, sink, and pool or in humid circumstances such as
basements or directly under rain.

The product should be connected to a grounded socket which is being protected by a fuse
complying with the values indicated in the "Technical Specifications" table. Our company
shall not be liable for the damages that may arise when the product is used before ensuring
that the grounding complies with local regulations.

The connection must be in compliance with national regulations. The power cable plug must
be easily accessible after installation. Voltage rating and allowable fuse protection are
specified in the “Technical Specifications” section. The specified voltage must be equal to
your mains voltage. A damaged power cable must be replaced by Authorized Service.
Damaged product must not be operated before repair! There is danger of electric shock!

September 2012 21
 J5 CHASSIS / TELEVISION

4.2. Input/Output Connections

AC IN Power cable input.

AV1 / S-VHS Euro/AV socket (CVBS signal, RGB signal); video and audio signal input for S-
Video camera (with Scart-SVHS converter).

COMPONENT Y Pb Pr Video signal input (YUV signal).

L R Audio signal input (YUV signal).

Optic Out Audio output sockets (optical) for PCM/AC3 signals. For connecting to a digital
multi-channel audio/video amplifier or AV receiver.

AUDIO OUT L R External audio output.

Audio Audio signal input for PC.

PC-IN VGA socket, video signal input for PC.

SATELLITE Satellite dish socket.

ANT IN Antenna socket.

HDMI1 HDMI socket, audio/video signal input (HDMI).

September 2012 22
 J5 CHASSIS / TELEVISION

HDMI2 HDMI socket, audio/video signal input (HDMI).

HDMI3 HDMI socket, audio/video signal input (HDMI).

HDMI4 HDMI socket, audio/video signal input (HDMI).

USB2 (HDD) USB hard disk socket for external data media and PVR function

LAN Network cable connection socket.

U Headphone connection (3.5 mm jack).

AV2 Video signal input for camcorder.

L R Audio signal input for camcorder.

USB1 USB socket for external data media and PVR function.

CI Common interface slot.

September 2012 23
 J5 CHASSIS / TELEVISION

4.3. Remote Control

4.3.1. GRUNDIG 3D Remote Control (TP7)

Turns on/off the television set (stand-

Turns on the television from by).
standby mode; selects channels
directly.

Switches between teletext and TV

Favourite list selection (»All«, »FAV 1« modes; opens/closes control menu
to »FAV 4«). when playing a file in DLNA menu

Opens 3D menu.

Opens Smart inter@ctive menu,

Displays information.
Zap function returns the menus
Opens the menu. one level back,

Opens the channel list.

Opens the electronic TV guide

Opens Tools menu.
Opens the pre-selection menu for AV
channels and the USB input. Then,
Adjusts the volume select with or
button and confirm with
button,

Turns volume on/off (mute),

Switches on the television from

Record, play, pause or stop (only standby; selects stations step by step.
digital television channels),

Opens PRnP menu.

Cursor Control

Moves the cursor up and down in the menus,

moves the cursor left/right in the menus,

Opens the channel list;

activates various functions.

September 2012 24
 J5 CHASSIS / TELEVISION

4.3.2. GRUNDIG 3D Remote Control (TP8/TP9)

Turn on/off the television set (stand-

Turns on the television from by).
standby mode; selects channels
directly.

Switches between teletext and TV

Favourite list selection (»All«, »FAV modes; opens/closes control menu
1« to »FAV 4«) when playing a file in DLNA menu

Opens 3D menu.

Opens Smart inter@ctive menu.

Displays information.
Zap function returns the
Opens the menu. menus one level back

Opens the channel list.

Opens the electronic TV guide

Opens Tools menu.
Opens the pre-selection menu for
AV channels and the USB input.
Adjusts the volume Then, select with or
button and press
to confirm,

Turns volume on/off (mute).

Switches on the television from
Record, play, pause or stop (only standby; selects stations step by
digital television channels), step.

Opens PRnP menu.

Cursor Control

Moves the cursor up and down in the

menus,

moves the cursor left/right in the menus.

Opens the channel list;

activates various functions.

September 2012 25
 J5 CHASSIS / TELEVISION

5. USING NEW PRODUCT FEATURES

5.1. Digital Satellite Settings and Setup (DVB-S2)

There are two ways of setting the digital satellite channels: The first simple setup and the
other is advanced setup.

5.1.1. Easy Installation

All antenna settings are preconfigured for Turksat 42° East satellite stations.
1. In Source Setup menu, Connection Type tab, with button, select Satelliteoption.
2. Using buttons, select Easy Installation tab and press OK .
3. Press ● (Green) button to start searching. Search Results menu appears and the search
for TV stations begins. Search may take several minutes depending on the number of
television stations received. The search ends when the PROGRAM TABLE appears.

5.1.2. Advanced Installation

if you want to receive the stations from a
different satellite, you must configure the
antenna settings (satellite, LNB Type, DISEqC
Mode, LNB selection) for the desired satellite.

1. In Source Setup menu, Connection Type tab,

with button, select Satelliteoption.
2. Using buttons, select Advanced
Installation tab and press OK . ANTENNA
SETTINGS menu will be displayed.
3. Using button, select Auto Tuning tab
and press OK . Select the satellite with
and buttons and press OK button. The
value in Transponder tab is not required for auto
tuning.
4. Use button to select LNB Power tab.
Depending on the LNB type, set LNB power to 13/18V or 14/19V with button.
5. Using button, select LNB Type tab and press OK. Select the LNB type used in the
satellite system with . Press ● (Green) to store the selection or press ● (Red) to
cancel it.

September 2012 26
 J5 CHASSIS / TELEVISION

6. Select DISEqC Mode tab with the button. Based on the number of current satellite
systems, use the button to select DISEqC 1.0 or DISEqC 1.1. DISEqC 1.0 allows
to receive maximum four satellites while DISEqC 1.1 allows to receive maximum 16
satellites at a time.
7. Select LNB Selection tab with button. Select the satellite that corresponds to the
relevant position with button.
8. Press ● (Red) for Auto Tuning. AUTO CHANNEL SEARCH menu will be displayed.
9. Use button to select Scan Mode tab. Press B / A to select whether you want to
search for only free digital television channels (Free), only scrambled digital television
channels (Scramble) or both (Free + Scramble).
10. Use button to select Service Type tab. Press to select whether you
want to search for only television channels (TV), only radio channels (Radio) or both (Radio +
TV).
11. Press ● (Red) button to start searching. Results menu appears and the search for TV
stations begins. Search may take several
minutes
depending on the number of television stations
received. The search ends when the PROGRAM
TABLE appears. If a second satellite is set,
perform the following steps to set other television
channels. Press M to open the menu. Select
SOURCE SETUP tab with button and
press OK. Then, select AUTOMATIC CHANNEL
SEARCH tab withD / C and press OK . In the
Select Satellite tab, press OK and select the
satellite with or buttons. Press ●
(Red) to start searching. Repeat other settings
starting from Step 7.

5.1.3. Digital Satellite Channel Settings

Automatic tuning of digital satellite channels:

New satellite channels are added or satellite data is changed frequently. Therefore, we
recommend you to run auto search function from time to time. Page LNB settings should be
have been made before automatic search.

1. PressM button.
2. Using button, select SOURCE SETTING tab and press OK. SOURCE SETUP
menu will be displayed.
3. Using button, select Kaynak tab and press seçip OK. Use ,
buttons to select Satellite and press OK.
4. Using button, select Automatic Channel Search tab and press OK. Menu will be
displayed.
5. Using button, select Select Satellite tab and press OK. SELECT SATELLITE
menu will be displayed.

September 2012 27
 J5 CHASSIS / TELEVISION

6. To search the list, select the desired satellite with , buttons and press OK.
7. Use button to select Scan Mode tab. Press to select whether you want
to search for only free digital television channels (Free), only scrambled digital television
channels (Scramble) or both (Free + Scramble)..
8. Use button to select Service Type tab. Press B / A to select whether you want to
search for only television channels (TV), only radio channels (Radio) or both (Radio + TV).
9. Use button to select Network Search tab. Select Acık with button. When
the Network search is set to On new transponder information is obtained and transponders
are scanned if there are any new transponders on the satellite.
10. Press ● (Red) button to start searching. Press ● (Red) to store new channels to be found
into the current channel list,
or press ● (Green) to delete all channel and favorite list and store them again. Search
Results menu appears and the search for TV stations begins. Search may take several
minutes depending on the number of television stations received. The search ends when the
PROGRAM TABLE appears.

Manual tuning of digital satellite channels:

If a certain channel cannot be found with automatic search, you can search it manually by
manual search function. You must enter all parameters of the channel correctly. You can
obtain the current transponder information from teletext page, satellite TV magazines or
internet.

1. Press M button.
2. Using button, select SOURCE SETTING tab and press OK. SOURCE SETUP
menu will be displayed.
3. Select Digital Manual Tuning with and press OK. Menu will be displayed.
4. Select the required tabs with . Enter (MHz) channel frequency in 5 digits by means
of number buttons. Symbol Rate (kS/s): Enter channel's symbol rate in 5 digits by means of
number buttons. Polarization: Select the channel polarization with
as Horizontal or Vertical. Network Search: Set the network search to On or Off with
. Scan Mode: Press to select whether you want to search for only free
digital television channels (Free), only scrambled digital television channels (Scramble) or
both (Free + Scramble). Service Type: Press to select whether you want to search
for only television channels (TV), only radio channels (Radio) or both (Radio + TV).
5. Press ● (Red) button to start searching. Results menu appears and the search for TV
stations begins.

September 2012 28
 J5 CHASSIS / TELEVISION

5.1.4. LNB Settings

1. PressM button.
2. Using button, select SOURCE SETTING tab and press OK. SOURCE SETUP
menu will be displayed.
3. Using button, select ANTENNA SETTINGS tab and press OK. Menu will be
displayed.
4. Select the required tabs with . Satellite: Select the desired satellite from the list with
or and press OK. Transponder: You can select a transponder from the list,
change or delete the current transponder or add a new transponder. LNB Power: Set LNB
power to OFF or, depending on the LNB type, to 13/18V or 14/19V with . LNB Type:
Select the LNB type used in the satellite system with and press ● (Green) to
store or ● (Red) to cancel it. 22KHz: Depending on LNB type, 22KHz is selected. In universal
LNB, this option is set to Automatic and cannot be changed. DISEqC Mode: Based on the
number of current satellite systems, select OFF, DiSEqC 1.0 or DiSEqC 1.1 with B / A
button. Off: It is used for satellite systems with single antenna. DiSEqC 1.0: DiSEqC 1.0
switch allows for receiving from maximum 4 satellites at the same time. DiSEqC 1.1: DiSEqC
1.1 switch allows for receiving from maximum 16 satellites at the same time. LNB selection:
In this tab, use to make selections between 1/16 and 16/16 for the satellite that
corresponds to the relevant DiSEqC positions.

5.1.5. SCR LNB Settings for Your TV

1. In the Source Setup menu, Connection Type tab, select Satellite with .
2. Select Advanced Installation with and press OK. ANTENNA SETTINGS menu
will be displayed.
3. Select LNB Type with and press OK. Select LNB type as Grundig SCR (Arçelik
SCR / Beko SCR) with button.
4. Enter the value with button in User Band tab, and press OK.
5. Select UB Frequency tab with . Enter the value and press OK.
6. Select LNB Selection tab with . Select the satellite that corresponds to the relevant
position with .
7. Press ● (Red) button for Auto Tuning. AUTO CHANNEL SEARCH menu will be displayed.
8. Use button to select Scan Mode tab. Press B / A to select whether you want to
search for only free digital television channels (Free), only scrambled digital television
channels (Scramble) or both (Free + Scramble).
9. Use button to select Service Type tab. Press to select whether you want
to search for only television channels (TV), only radio channels (Radio) or both (Radio + TV).
10. Press ● (Red) button to start searching. Results menu appears and the search for TV
stations begins. Search may take several minutes depending on the number of television
stations received. The search ends when the PROGRAM TABLE appears.

September 2012 29
 J5 CHASSIS / TELEVISION

NOTES:

1. Use the installation equipment supported/recommended by your SCR switch.

2. Changing the user band number and frequency determined during installation may cause
problems that can affect other users/receivers in the system.

3. User Band numbers are inscribed on the switch and each user/receiver should use a
specific user band.

3. Performing auto search on two receivers (TVs) simultaneously may cause problems.

5.2. 3D Function

5.2.1. 3D Picture Viewing

3D function is only effective at »HDMI«, »YPbPr«, »VGA«, »USB«, »DLNA«, »DVB-T«,
»DVB-C« and »DVB-S« sources. With »HDMI«, »YPbPr« and »VGA« inputs, 3D mode is not
active except resolutions at »1280x720p 50/60 Hz«, »1920x1080i 50 /60 Hz« and
»1920x1080p 24 / 30, 50 / 60 Hz«. 3D experience may change depending on the format and
features of the picture (resolution, sharpness and etc) supplied from the external input. 3D
effect may degrade if you watch 3D images under fluorescent light. In such cases, either
reduce the light or turn off the lamp. While 3D mode is active, if Manual or Automatic search
menus, Program Table or EPG menu are turned on, the channel or the source are changed,
or the playback is completed or the next file starts to play in USB or PVR modes, your TV will
switch to 2D mode.

1. Open the »Select Source« menu with »AV«.

2. Select AV source that will be played 3D with »<«, »>« or »V«, »Λ« button and confirm with
»●«.
3. Select the 3D mode with »3D« as »Side by Side« or »Top Bottom« in accordance with the
content to be played and confirm with »●«.

– »2D → 3D«: Changes 2D picture to 3D.

– »Side by Side«: Displays a picture next to the other one.
– »Top Bottom«: Displays a picture below the other one.
–»Frame Packing«: Right and left images of the TV are displayed
alternatively.

Note:
Frame Packing appears in 3D menu only if a video signal is send
from an external device
that supports HDMI 1.4. Side by Side and Top Bottom options do
not appear. Turn of the function by setting it to »Off« with »3D«
button.

September 2012 30
 J5 CHASSIS / TELEVISION

5.2.2. 3D Picture Settings

1 Open the menu with »i« button.
2. Select »PICTURE SETTINGS« menu with »V« or »Λ« and confirm with »●« Menu will be
displayed.
3 Select »3D SETUP« with »Λ« and confirm with »●« .
– »3D SETUP« menu will be displayed.

5.2.3. Adjusting 2D>3D Effects

When you change 2D broadcasting to 3D, you can adjust the most suitable effect depending
on your personal preferences.
1 Select »Effect mode« with »V« or »Λ« and set it to »On« with »<« or »>«.
– »3D Perspective« and »Depth« options are activated.
2 Select »3D Perspective« with »V« or »Λ« and adjust with »<« or »>«.
3 Select »Depth« with »V« or »Λ« and select the picture setting as »Low«, »Medium« or
»High« with »<« or »>«.
4 Press »i« to end the setting.

5.2.4. Left-Right Correction

When Frame Packing mode is enabled in HDMI source, 3D perception may disappear in 3D
films or 3D games due to a synchronization shift arising from HDMI signal. You may correct
3D perception with this feature.
1 Select »LR Correction« with »V« or »Λ«.
2 Press »<« or »>« to switch the function »On«.
Note:
Turn off the function by setting it to »Off« with »<« or »>«.
3 Press »i« to end the setting.

5.2.5. Formats supported with HDMI 1.4

With HDMI 1.4, your TV can automatically recognize and play 3D contents. To exit 3D mode,
turn off the function by setting it to »Off« with »3D« button. Formats supported in 3D mode
with HDMI 1.4 are provided in the following table.
hh:mm

Movie Content Frame Packing. 1080p @ 23.98/24Hz

Game Content Frame Packing
720p@50 or
59.94/60Hz
Broadcast Content Side by Side 1080i @ 50 or
Horizontal 59,94/60Hz
Top and Bottom 720p @ 50 or
59.94/60Hz 1080p @
23.97/24Hz

September 2012 31
 J5 CHASSIS / TELEVISION

5.2.6. Dual Gaming Feature

Dual Gaming feature is added to J5-chassis products from software version 1.13.
Two persons can see different screens while playing a game with each other thanks
to this feature. This feature must be supported by the game and the game console
should support this feature in order to use the feature. The important point here is to
inform the customer that Dual gaming glasses are different than normal 3D glasses.
The technology here is summarized below.
Normally, 3D perception is obtained by providing different images to left and right
eyes. Different images are obtained by adding filters on the glasses. Dual gaming
glasses may be summarized as filters for right eye on one glasses and filters for left
eye on the other glasses. Here, right eye is assigned to 1st player, and left eye is
assigned to the 2nd player. Another important note is that the image is not 3D, but
2D in dual gaming.

5.3. Inter@ctive TV and Home Network

Grundig Smart Apps is a store where various applications that can be used on your Grundig
TV are available. You may download many applications from Grundig Smart Apps. These
applications are those such as video and audio chat, video, picture and music applications,
social networks, news and sports applications, weather forecast application and doctor or
pharmacy search, recipe viewing and viewing traffic congestions depending on your local
city. Your TV supports remote control application for Apple iPhones and Android smart
phones. You can download ≫GRUNDIG TV Remote≪ application to your phone free of
charge from Apple App Store or Google Play (Android Market) depending on the
specifications of your phone and control your TV with your phone.
5.3.1.Wired Network Connection

You can establish a wired or wireless connection between your television and the local
network. For wired network connection, connect the output of external modem to »LAN«
socket by using a Cat5 cable.

September 2012 32
 J5 CHASSIS / TELEVISION

5.3.2. Wired Network Settings

There are two ways of making the wired network settings.
A In auto connection, all data regarding connection settings (»IP Address«, »Netmask «,
»Gateway« and »DNS«) are obtained from modem automatically.
B In manual connection, all data regarding connection settings (»IP Address«, »Netmask «,
»Gateway« and »DNS«) should be manually configured.

5.3.3.Auto Connection
Most of the home networks are Dynamic networks. If you have a dynamic network, you must
use a DSL modem that supports DHCP. Modems and IP sharers that support DHCP obtain
the »DNS« values required for »IP Address«, »Netmask«, »Gateway« and internet access
automatically, and thus you are not required to enter those values manually.
1. Open the menu with »MENU« button.
2 Select »NETWORK APPS« menu with
»V« or »Λ« and confirm with »●«
– »NETWORK APPS« menu will be
displayed.İnter@ctive Application Type Automatic
3 Select »Connection« option with »V« or
»Λ« and select »Wired« with »<« or »>«.
4 Select »Connection Type« option with »V«
or »Λ« and select »Auto« with »<« or »>«.
5 Select »Connect« with »« (red) button to
establish the modem connection.
– »Connecting ... Please wait« message will
be displayed.
6 Press »« (green) button to make sure that
the network connection is established with
the current settings.
– »Testing ... Please wait« message will be
displayed and if it is connected successfully,
»Connection to Gateway : Success«,
»Internet Connection: Success« message
will be displayed. Press »i« to end the
setting.

Note: If you do not have a dynamic network, follow the instructions in manual connection
section.

5.3.4. Manual Connection

Certain networks require Static IP address. If your network requires a Static IP address, you
must enter the »IP Address«, »Netmask«, »Gateway« and »DNS« values manually. You can
obtain your »IP Address«, »Netmask«, »Gateway« and »DNS« values from your Internet
Service Provider (ISP).
1 Open the menu with »i« button.
2 Select »NETWORK APPS« menu with »V« or »Λ« and confirm with »●«
– »NETWORK APPS« menu will be displayed.

September 2012 33
 J5 CHASSIS / TELEVISION

3 Select »Connection Type« option with »V«

or »Λ« and select »Wired« with »<« and
»>«.
4 Select »Network Configuration« option
with »V« or »Λ« and select »Manual« with
»<« and »>«.
- »IP Address«, »Netmask«, »Gateway«
and »DNS« options are active.
5 Select »IP Address« with »V« and press
»●«. Enter the IP address with »1…0«
buttons and press » « (green) to save the
value.
6 Select »Netmask« with »V« and press
»●«. Enter the Netmask address with
»1…0« buttons and press » « (green) to
save the value.
7 Select »Gateway« with »V« and press
»●«. Enter the Gateway address with
»1…0« buttons and press » « (green) to
save the value.
8 Select »DNS« with »V« and press »●«.
Enter DNS address with »1…0« buttons and
press » « (green) to save the value.
9 Select »Connect« with » « (red) button to establish the modem connection.
– »Connecting ... Please wait« message will be displayed.
10 Press »« (green) button to make sure that the network connection is established with the
current settings.
– »Testing ... Please wait« message will be displayed and if it is connected successfully,
»Connection to Gateway : Success«, »Internet Connection: Successful« message will be
displayed.
11 Press »i« to end the setting.

5.3.5. Wireless Network Connection

Television includes a built-in Wireless 2 x WiFi Adapter to connect it to a wireless
network.
Note: Apart from the built-in WiFi adapter on TV, external USB WiFi adapter can be
connected to »USB1« and »USB2 (HDD)« inputs.

September 2012 34
 J5 CHASSIS / TELEVISION

5.3.6. Wireless Network Settings

A In automatic connection, all data regarding connection settings (»IP Address«, »Netmask
«, »Gateway« and »DNS«) are obtained from modem automatically, except for Access Point
Selection.
B In manual connection, all data regarding connection settings (»IP Address«, »Netmask «,
»Gateway« and »DNS«) should be manually configured.

5.3.7. Auto Wireless Network Connection

Most of the home networks are Dynamic networks. If you have a dynamic network, you must
use a DSL modem that supports DHCP. Modems and IP sharers that support DHCP obtain
the »DNS« values required for »IP Address«, »Netmask«, »Gateway« and internet access
automatically, and thus you are not required to enter those values manually.
1. Open the menu with »MENU« button.
2 Select »NETWORK APPS« menu with »V« or »Λ« and confirm with »●«
– »NETWORK APPS« menu will be displayed.
3 Select »Connection Type« option with »V« or
»Λ« and select »Wireless« with »<« and »>«.
4 Select »Network Configuration« option with
»V« or »Λ« and select »Auto« with »<« and
»>«.
5 Go to »Select Access Point« option with »V«
or »Λ« and confirm with »●«
– »Select Access Point« menu appears and
available wireless networks are scanned and
displayed in the menu.
6 Select the network that you want to connect
with »V«, »Λ«, »<« or »>« and confirm with
»●«.
- Wireless connection password screen is
displayed.
7 Select the character with »V«, »Λ«, »<« or
»>« and move to the next character with »●«.
– Select »ABC« for uppercase or »abc« for
lowercase and confirm with »●«.
– Select »?@123« for numbers or symbols
and confirm with »●«.
– To clean the characters, select » « button and confirm with »●«.
– Enter the password and select »Confirm« with »V«, »Λ«, »<« or »>« and confirm with
»●«.

Note: In WEP encryption system, more than one network password can be assigned to the
network. Your television can connect the network only with the password in level one. For TV
to discover the wireless modem on the network, the network name should support ASCII
characters.
8 Select »Connect« with »« (red) button to establish the modem connection.
– »Connecting ... Please wait« message will be displayed.
9 Press »« (green) button to make sure that the network connection is established with the
current settings.
– »Testing ... Please wait« message will be displayed and if it is connected successfully,
»Connection to Gateway : Success«, »Internet Connection: Successful« message will be
displayed.
10 Press »i« to end the setting.

September 2012 35
 J5 CHASSIS / TELEVISION

Note: If you do not have a dynamic network, follow the instructions in manual connection
section.

5.3.8. Manual Wireless Network Connection

Certain networks require Static IP address. If your network requires a Static IP address, you
must enter the »IP Address«, »Netmask«, »Gateway« and »DNS« values manually. You can
obtain your »IP Address«, »Netmask«, »Gateway« and »DNS« values from your Internet
Service Provider (ISP).
1. Open the menu with »MENU« button.
2 Select »NETWORK APPS« menu with »V« or »Λ« and confirm with »●«
– »NETWORK APPS« menu will be displayed.
3 Select »Connection Type« option with »V« or »Λ« and select »Wireless« with »<« and »>«.
4 Go to »Select Access Point« option with »V« or »Λ« and confirm with »●«
– »Select Access Point« menu appears and available wireless networks are scanned and
displayed in the menu.
5 Select the network that you want to connect with »V«, »Λ«, »<« or »>« and confirm with
»●«.
- Wireless connection password screen is displayed.
6 Select the character with »V«, »Λ«, »<« or »>« and move to the next character with »●«.
– Select »ABC« for uppercase or »abc« for lowercase and confirm with »●«
button.
– Select »?@123« for numbers or symbols and confirm with »●«.
– To clean the characters, select » « button and confirm with »●«.
– Enter the password and select »Confirm« with »V«, »Λ«, »<« or »>« and confirm with »●«
button.
Note: In WEP encryption system, more than one network password can be assigned to the
network. Your television can connect the network only with the password in level one. For TV
to discover the wireless modem on the network, the network name should support ASCII
characters.
7 Select »Network Configuration« option with »V« or »Λ« and select »Manual« with »<« and
»>«.
– »IP Address«, »Netmask«, »Gateway« and »DNS« options are active.
8 Select »IP Address« with »V« and press »●«. Enter the IP address with »1…0« buttons
and press » « (green) to save the value.
9 Select »Netmask« with »V« and press »●«. Enter the Netmask address with »1…0«
buttons and press » « (green) to save the value.
10 Select »Gateway« with »V« and press »●«. Enter the Gateway address with »1…0«
buttons and press » « (green) to save the value.
11 Select »DNS« with »V« and press »●«. Enter DNS address with »1…0« buttons and
press » « (green) to save the value.
12 Select »Connect« with »« (red) button to establish the modem connection.
– »Connecting ... Please wait« message will be displayed.
13 Press »« (green) button to make sure that the network connection is established with the
current settings.
– »Testing ... Please wait« message will be displayed and if it is connected successfully,
»Connection to Gateway : Success«, »Internet Connection: Successful« message and MAC
address will be displayed.
14 Press »i« to end the setting.

5.4. Smart Inter@ctive TV 2.0 Internet Applications

Smart Inter@ctive TV 2.0 interactive applications provide your television with internet
services and pages. These applications are designed according to your television. Through
Smart Inter@ctive TV 2.0 feature you can run many local and global internet applications.
Grundig Appstore allows you to obtain various applications you may use with your Grundig

September 2012 36
 J5 CHASSIS / TELEVISION

TV. You may download many applications from Grundig Appstore. These applications are
those such as video and audio chat, video, picture and music applications, social networks,
news and sports applications, weather forecast application and doctor or pharmacy search,
recipe viewing and viewing traffic congestions depending on your local city.

List of applications available in Grundig Appstore in the first production:

1- Skype
2- Youtube
3- Reuters
4- İBB Trafik
5- Facebook
6- Twit Talk
7- Yemek sepeti
8- Ebay
9- Picasa
10- Flickr
11- Bon Gusto
12- YogaMour
13- Auto Motor Sport
14- goal724
15- apotheken
16- arztsuche
17- Bild
18- Laufen
19- Mackolik
20- Funsport
21- NTVSport
22- NTV
23- Viewster
24- Baby Watch
25- World Weather Online
26- Trip Advisor
27- Garanti
28- HRS

5.4.1. Starting with Smart Inter@ctive TV

1. Open the menu with »MENU« button.
2 Using ≫V≪ or ≫Λ≪ buttons, select≫INTER@CTIVE TV≪ menu and confirm
with ≫OK≪. Menu will be displayed.
3 Using ≫V≪ or ≫Λ≪ buttons, select≫Inter@ctive Applications≪ and confirm with
≫OK≪.
– ≫Inter@ctive Applications≪ menu shall be displayed. Grundig Smart Apps
registration screen will be displayed if you are logging in for the first time.

September 2012 37
 J5 CHASSIS / TELEVISION

5.4.1.1. Creating a Grundig Smart Apps account

You need to be registered to access all applications in Grundig Smart Apps.

1 To open ≫SMART inter@ctive TV≪ menu, press ≫@≪ button. – Grundig Smart Apps
registration screen shall be displayed.
2 To start the registration procedure, press ≫OK≪.
3 Enter your ≫Name≪ and ≫Surname≪:
Select each character of your information with ≫V≪, ≫Λ≪, ≫<≪ or ≫>≪ buttons and
confirm with ≫OK≪. After entering the data completely, use ≫V≪, ≫Λ≪, ≫<≪ ve ≫>≪
buttons to select ≫x≪ and confirm with ≫OK≪. Press ≫V≪ to move to the next input line
and press ≫OK≪ to view the keyboard. Press ≫••••≪ (blue) to move to the next screen and
press ≫OK≪ to view the keyboard.
4- Enter an e-mail address:
Enter the information, and use ≫V≪, ≫Λ≪, ≫<≪ and ≫>≪ buttons to select ≫x≪ on the
screen keyboard and confirm with ≫OK≪. Press ≫••••≪ (blue) to move to the next screen
and press ≫OK≪ to view the keyboard.
5- Enter password and confirm:
Select each character of the information with ≫V≪, ≫Λ≪, ≫<≪ or ≫>≪ buttons and
confirm with ≫OK≪. After entering the data completely, use ≫V≪, ≫Λ≪, ≫<≪ and ≫>≪
buttons to select ≫x≪ and confirm with ≫OK≪. Press ≫V≪ to move to the next input line
and press ≫OK≪ to view the keyboard. Press ≫••••≪ (blue) to move to the next screen
and press ≫OK≪ to view the keyboard.
6- Enter a location:
Enter the information, and use ≫V≪, ≫Λ≪, ≫<≪ and≫>≪ buttons to select ≫x≪ on the
screen keyboard and confirm with ≫OK≪.
7- Enter a phone number (optional):
Enter the information, and use ≫V≪, ≫Λ≪, ≫<≪ and≫>≪ buttons to select ≫x≪ on the
screen keyboard and confirm with ≫OK≪.
8- To complete the registration procedure, press ≫••••≪ (blue) button.
9- To read and accept the terms of use, press ≫OK≪. ≫Inter@ctive Applications≪ menu
shall be displayed and standard applications shall be downloaded and installed to your TV.

September 2012 38
 J5 CHASSIS / TELEVISION

5.4.1.2 Logging in to the Grundig Smart Apps account

When you reset your TV to factory settings for any reason, the applications you have
downloaded shall be deleted if you have not selected the ≫Retain installed applications≪
option, and registration screen shall be displayed again when you enter the ≫Inter@ctive
Applications≪menu. You can re-login to Grundig Smart Apps without registering again with
the e-mail you have provided in the registration procedure and with the password you have
created.

5.4.1.3. Selecting internet applications

1- To open ≫SMART inter@ctive TV≪ menu, press ≫@≪ and then ≫••••≪ (red) buttons.

2- Select application categories with ≫V≪ or ≫Λ≪ buttons and press ≫>≪ to move to the
application field.
3- Select the desired application with ≫V≪, ≫Λ≪, ≫<≪ or ≫>≪ buttons and confirm with
≫OK≪. Main menu of the application shall be displayed after a short while.

5.4.1.4 Grundig Appstore

Grundig Appstore is an online store where applications that will be used on the TV can be
downloaded. Some applications on ≫ SMART inter@ctive TV≪ menu are installed on your TV
by the factory. You may download many applications from wide application choices in the
Grundig Appstore.

1- To open ≫SMART inter@ctive TV≪ menu, press ≫@≪ and then, press the ≫••••≪ (red)
button. ≫SMART inter@ctive TV≪ menu shall be displayed.

September 2012 39
 J5 CHASSIS / TELEVISION

2- To enter the ≫Grundig Appstore≪, press ≫•≪ (red) button. ≫Grundig Appstore≪ menu
shall be displayed.

5.4.1.5. Downloading and removing internet applications

1- Select the category you want to access in Grundig Appstore with ≫V≪ or ≫Λ≪ buttons
and press ≫>≪ button to move to the application field; and select the application you desire
with number buttons.
– ≫1≪ – ≫Most Popular≪,
– ≫2≪ – ≫Favorites≪,
– ≫3≪ – ≫Release Date≪;
or press the ≫••≪ (green) button to search the application by name and select the application.
2- Select the application you want to download with ≫V≪, ≫Λ≪, ≫<≪ or ≫>≪ buttons and
confirm with ≫OK≪. Application information will be displayed.
3- To download and install the application, press ≫••••≪ (blue) button. - Application shall be
downloaded and installed.

5.4.1.6. Removing internet applications

1- Select application categories with ≫V≪ or ≫Λ≪ buttons and press ≫>≪ to move to the
application field.
2- Select the application you want to remove with ≫V≪, ≫Λ≪, ≫<≪ or ≫>≪ buttons and
press ≫•≪ (red) button. Safety warning will be displayed.
3- Press ≫OK≪ to confirm the removal of application or press ≫<≪ to cancel the removal of
application.
4- Complete the procedure with ≫OK≪.

September 2012 40
 J5 CHASSIS / TELEVISION

5.4.1.7. Moving internet applications

You may change the order of the applications installed on your TV according to your
preferences.
1- To select ≫All Applications≪ category, use ≫V≪ or ≫Λ≪ buttons and press ≫>≪ to move
to the application field.
2- Select the application you want to move with ≫V≪, ≫Λ≪, ≫<≪ or ≫>≪ buttons and press
≫••••≪ (blue) button.
3- Press ≫V ≪, ≫Λ≪ and≫<≪, ≫>≪ buttons to move the application to the new location
and press ≫OK≪ to confirm.

5.4.1.8. Scoring internet applications

You may score applications installed on your TV individually.

1- Select application categories with ≫V≪ or ≫Λ≪ buttons and press ≫>≪ to move to the
application field.
2- Select the application you want to score with ≫V≪, ≫Λ≪, ≫<≪ or ≫>≪ buttons and press
≫•••≪ (yellow) button.
3- Select application score with ≫V≪, ≫Λ≪, ≫<≪ or ≫>≪ buttons and press ≫OK≪ to save
the score; or press ≫<≪to cancel scoring.

5.4.2 SKYPE

connection free of charge in the comfort of

your living room. An internet connection
and the GRUNDIG G-VCAM-01 USB
Camera and microphone unit that you may
purchase only are required for this.
Contact the dealership you have
purchased your TV for purchasing
Your TV is SkypeTM-ready. With the information on camera and microphone
Plugged Into SkypeTM feature you can unit. Use your SkypeTM account or create
make audio and video calls from SkypeTM a new SkypeTM account from your TV.
to SkypeTM with your friends or family
anywhere on the world via internet

Connection settings;

- Your TV is compliant with GRUNDIG G-VCAM-01 camera unit; however camera units
of other brands are not supported.
- GRUNDIG G-VCAM-01 camera unit is sold separately; it is not delivered with the TV.
Contact the dealer you have purchased your TV for detailed purchasing information.
- Before connecting the Skype camera, we advise you to switch the television to stand-
by mode.

- Your TV shall be connected to internet in order to use the SkypeTM feature. SkypeTM
cannot be used for emergency calls. SkypeTM is not a replacement for a phone and it
cannot be used for emergency calls.
- Making SkypeTM calls over wireless network may affect the audio and video quality
negatively.
- Connect GRUNDIG G-VCAM-01 Camera and Microphone unti directly to the ≫ USB1≪
or ≫
USB2 (HDD)≪interface of your TV.

September 2012 41
 J5 CHASSIS / TELEVISION

- Audio and video calls with other SkypeTM users are free of charge. SkypeTM Credits
or a subscription is required for other SkypeTM services such as calling cell phones or
landline phones with lower costs.
- Audio quality of the microphone may be affected adversely in a noisy environment.
- Skype is deactivated and incoming calls cannot be accepted when the TV is turned
off.
- Trademark Statement: Skype is a trademark of Skype and its affiliate companies. This
product/application is not approved or supported by Skype, Skype Communications
S.a.r.l. or any of their subsidiaries.
- Skype IP Statement: This product includes SkypeKit Release [ ] Copyright 2003-2011,
Skype Patent Pending Skype, relevant trademarks and logos are the trademarks of
Skype.

1- Install the camera on the TV.

2- Connect the USB cable to the ≫USB1≪ or ≫USB2 (HDD)≪ interface of the TV.

5.4.3. Selecting and Installing the BABYCAM application

1- To open ≫SMART inter@ctive TV≪ menu ≫, press@≪ and then ≫••••≪ (red) button.
2- Select ≫All Applications≪ category ≫ withV≪ or ≫Λ≪ and press ≫>≪ to move to the
application field.
3- Select ≫BABYCAM≪ application with ≫V≪, ≫Λ≪, ≫<≪ or ≫>≪ button and press
≫OK≪. Main menu of the application shall be displayed after a short while.

5.4.3.1 BABYCAM network installation

Connect the camera to home network and log in a session:

You shall connect to home network and log in to ensure that the camera image is displayed
on your TV via "BABYWATCH" application.

Note: TV and camera should be connected to the same network via a “modem” or “router”.

It is not required that the home network is connected to internet; you can launch Baby Watch
application through “Quick Apps” menu. You can connect your camera to the home network
with a LAN connection or wirelessly by WLAN.

September 2012 42
 J5 CHASSIS / TELEVISION

Connecting the camera with a LAN connection and logging in:

1 Turn the TV on.
2 Use »@« button to select »Quick Apps« menu.
3 Select »Online Store« item with »« (green) button. – »Online Applications« menu shall
be displayed on the screen.
4 On the »Online Applications« menu, use »>« to move to the applications field, select
»BabyWatch« application with »V«, »Λ«, »<« or »>« buttons and install with »••••« (blue)
button. – Application log in menu shall be displayed after a short while.
5 Press »OK« to confirm the statement. – Camera menu will be displayed.
6 Select »Search Camera« tab with »V« or »Λ« and confirm with »OK«. – Camera IP
address shall be displayed after a short while.
7 Select the camera with »V« or »Λ« and confirm with »OK«. – Name and password entry
menu of the camera shall be displayed.
8 Press »OK« to view the keyboard on screen.
9 Enter the name of the camera – as described in the notes (User Manual) – and save.
10 Select »Password« tab with »V« and view the keyboard on the screen with »OK«. Enter
»admin« password – as described in the notes – and save.
Note:
- We advise you to use a password of your own. (BabyWatch camera user manual,
page 14, "Settings" section.)
11 Use »V« button to select »OK« and confirm with »OK«.
12 Press »« (red) button twice to switch to "live view". – Camera "live view" shall be
displayed on the screen.

Registering the camera via WLAN connection:

Note: Camera should be connected to the TV set via a wired LAN connection first. After
completing wired connection correctly, you can switch to wireless connection from camera
menu settings.

1 Turn the TV set on.

2 Use »@« button to select »Quick Apps« menu.
3 Select »BabyWatch« application with »V« or »Λ« and confirm with »OK«. – Camera "live
view" shall be displayed on the screen
.
4 While viewing "live view" on the screen, select »Settings« menu with »•« (red) button.
5 Select »Camera Settings« tab with »V« or »Λ« and confirm with »OK«. – Camera
connected with LAN is displayed on the screen.
6 Use »OK« button to enter camera settings, and select »Wireless Connection« tab with »V«
or »Λ« and confirm with »OK«.
– Available networks shall be displayed after a short while. Select the desired network with
»V« or »Λ« and confirm with »OK«. – Network name and password entry menu shall be
displayed on the screen.
7 Activate »Password« tab with »OK«.
8 Press »OK« and use the keyboard to enter »admin« password and save.
9 Use »V« button to select »OK« and confirm with »OK«.

September 2012 43
 J5 CHASSIS / TELEVISION

5.5.4. GRUNDIG voice controlled remote - installation

Connecting the USB hardware lock:

1-) Insert the USB hardware lock to the »USB1« or »USB2 (HDD)« connector of the TV.

Introduction of Remote Control:

1 Press and hold the »AV SYNC« button on the remote control. – LED on the USB hardware
lock flashes in blue.
2 Press and hold the button on the USB hardware lock for 3 seconds. – LED on the remote
illuminates in blue, and the introduction procedure is completed successfully.

Notes:

If the LED on the remote is red, the procedure is not successful, please repeat the
procedure.

After completing the introduction procedure successfully, »Voice Controlled Remote Status«
label is displayed in the »SETTINGS« menu.

To check the registration procedure, press »MENU«button and select »SETTINGS« tab
with »V« or »Λ« buttons and confirm with »OK«. Then, select and view the »Voice
Controlled Remote Status« tab with »V« or »Λ«.

Searching for lost remote:

You can find the remote control with this feature if you lose the remote.
1 Press the button on the USB hardware lock. – An audible signal shall be given from the
remote after a short while.
2 Stop the audible signal by pressing any button on the remote after finding it.
Advanced functions
Notes:

Press and hold the » « button before a “Voice command".

Do not cover the microphone on the remote control.

Best distance between your mouth and the remote is 30 cm.

Do not talk too loud.

Give the commands while blue LED is illuminated and » « warning is displayed on the
TV.

September 2012 44
 J5 CHASSIS / TELEVISION

Using Voice Controlled Remote as a Mouse with "Gyro" feature

Your voice controlled remote is also equipped with gravitational sensors. Thanks to these
sensors, your remote can sense the movements and use the information when we move our
hand to right or left. We first switch to Mouse mode in the Web Browser application. Then,
we press the "@" key of the remote control for a while to activate this feature. We can see if
this feature is activated by means of the mouse movements. We can also press the "@"
again to deactivate this feature.

September 2012 45
 J5 CHASSIS / TELEVISION

5.5.4.1 Voice Commands List for Voice Controlled Remote

September 2012 46
 J5 CHASSIS / TELEVISION

5.5. DLNA Home Network Connection

With DLNA menu of your television, you can easily access Video, music and photo files on
server; and thanks to DMR feature, you can automatically start and stop media playing on
devices with DMC feature.
Notes:
You can share your video, music and image files through devices such as PC, mobile phone
or NAS (Network Attached Storage) that function as DMS (Digital Media Server) compatible
with DLNA.
If the DMS device and the TV are connected to the wireless network at the same time, there
may be lags and freezings during video playback.
TV can also operate with DMS software that can be installed on a computer but, it is not
guaranteed that it will run in full compatibility with software without a DMS certificate.
Perform the following steps for a sample DMS set up. Open Windows Media Player11’i on a
computer with Windows operating system. In »Library« tab, select »Media Sharing«. On the
pop-up window, check »Share my media« and press »OK«. The new window displays the IP
numbers of connected devices. To enable the TV to detect the computer, you need to select
the television's IP number. If IP is not listed in the window, select »Settings« option in »Media
Sharing« menu and check »Allow new devices and computers automatically« in the pop-up
menu. After completing these processes, the television can only view the supported file
formats in the Library. In order not to encounter any problems with media sharing, check the
firewall settings of your modem and computer.

5.5.1. Selecting Digital Media Server

1. Open the menu with »Menu«

button.
2 Select »NETWORK APPS« menu
with »V« or »Λ« and confirm with
»●«. Menu will be displayed.
3 Select »Inter@ctive Applications«
with »V« or »Λ« and confirm with
»●«. »Inter@ctive Applications«
menu will be displayed.
4 Select »DLNA« option with »V«,
»Λ«, »<« or »>« and confirm with
»●«
button.
– »DLNA« menu will displayed. 0
Device Found Page: 1/1 Press
BLUE key to search DMS device. Refresh
5 Press » « (Blue) to discover DMS devices on home network.
– The found DMS devices will appear in the menu.
Note: If DMS devices are not displayed, check Network connection.

September 2012 47
 J5 CHASSIS / TELEVISION

6 Select DMS device you like with »V«, »Λ«, »<« or »>« and view the contents with »●«.
Notes: File and folder structure of the DMS device in menu may vary depending on the
Digital Media Server software in use. Subtitles are not supported on video files that are
played through the DMS device.
7 Video files played through DMS device (»MPEG_PS_NTSC«, »MPEG_PS_PAL«,
»MPEG_TS_SD_EU« and »MPEG_TS_EU_ISO«) support DLNA certified formats.
In videos with high bit rate, lag problem might be seen. Folders that appear as unknown in
DLNA application cannot be played by the TV. Installing the codec to your computer can
solve this problem. Audio files played through DMS device (»AAC_ADTS_320«, »LPCM«,
»MP3«, »WMABASE« and »WMAFULL«) support DLNA certified formats. Image files played
through DMS device (»JPEG_LRG«, »JPEG_MED« and »JPEG_SM«) support DLNA
certified formats.
7 Press »Z« to return to the DMS list page.
8 Press »TV-G« to exit DLNA feature.

5.6. USB Functions

5.6.1. Recording TV Programmes (PVR)

Recording programmes to view them later can only be done with digital television stations
(DVB-S, DVB-T and DVB-C). You can record and playback digital television stations (DVB-S,
DVB-T and DVB-C) depending on the broadcasting station. Recording and playing
programmes, as well as TimeShift function can only be carried out by using an external data
medium (hard drive or USB stick). The data medium must have a capacity of at least 2 GB.
Recordings can be made with most data mediums on the market. However, we cannot
guarantee operation for all data media. If you record a programme on an external data
medium, you can only watch it on your television. You will not be able to watch this
programme on any other device. If you send your product to be repaired and hardware
components need to be replaced, you might not be able to play the recordings again on the
repaired television. Reception for SKY broadcasting station is currently only possible in
Germany with a suitable set-top box.

Before connecting the data medium,

switch the television to stand-by with »8«.
Connect the device and then switch the
television on again. Before disconnecting
the external data medium, the television
must first be switched to standby,
otherwise files can be damaged. There are
two USB slots, namely »USB1« and
»USB2 (HDD)«, on the TV. »USB2
(HDD)« input is intended for connecting
USB devices that require additional power
(e.g. external hard disk).

September 2012 48
 J5 CHASSIS / TELEVISION

Plug the memory stick into the »USB1« interface of the television. Or plug the external hard
disk to the »USB2 (HDD)« interface of television. 2 Confirm the » « display with » « (green).
– The file browser appears.
Notes: »USB1« interface of the television supports 500mA current according to the USB
standard. Devices such as external hard disk and etc. that consume more power can only be
connected to the »USB2« interface of the television.
If you are using a power cable for the external hard disk that you have connected to the
»USB2 (HDD)« interface, then the power cable of the external hard disk must also be
unplugged when the TV is turned off.
You must not disconnect the USB Device from the TV while a file on the USB Device is being
read by the TV.

5.6.2. Time Shift – Pause Programme

You can pause the programme that you are watching. This is a useful function. For instance,
if the phone rings when you are watching a movie, you can pause the movie and resume it
after the call without missing nothing. The last scene that was frozen is displayed and time
shift is recorded into the external data media. In Time Shift mode, you can only record as
much as the free memory space on the external data media. When the Time Shift starts,
recording time is calculated and displayed based on the free space.

5.7. USB Mode

File formats:
Your television can be operated via the USB input with the following file formats:
Video compression / decompression (codec) is intended for decreasing the storage area
without compromising the picture quality. Your television can playback video data
compressed in DIVX, XVID, H.264/MPEG-4 AVC (L4.1, Ref. Frames:4), MPEG-4, MPEG-2,
MPEG-1, MJPEG, MOV standards.
File extensions supported by the device: “.avi”, “mkv”, “.mp4”, “.ts”, “.mov”, “.mpg”, “.dat”,
“.vob”. In addition to video data, these files also contain audio data compressed and
"packaged" by using MP3, AAC or Dolby Digital©.

Audio data
Your television can play audio data coded with MP3, AAC and WMA standards. MP3 stands
for MPEG-1 Volume Level 3 and is based on the MPEG-1 standard developed by MPEG
(Motion Picture Expert Group). AAC stands for Advanced Audio Coding developed by
MPEG. AAC provides higher audio quality with the same data rate (bit rate). WMA (Windows
Media Audio) is a compression standard developed by Microsoft for audio data. These
formats enable audio files to be saved on storage devices with a sound quality similar to that
of a CD. File extensions supported by the device: “.mp3”, “.mp2”, “.wma”, “.m4a”, “.aac”. MP3
files can be organized in a similar way to the folders and subfolders in a PC.

Picture data
Your television can display picture data in JPEG, PNG and BMP formats.
JPEG stands for Joint Picture Experts Group. This process is intended to compress picture
files. PNG and BMP standards are intended to compress picture data without loss. Picture
files can be saved in a data storage medium together with other file types. Such files can be
organised as folders and subfolders.

September 2012 49
 J5 CHASSIS / TELEVISION

5.7.1. Connecting External Data Storage Devices

Before connecting the data medium, switch the television to stand-by with »8«. Connect the
device and then switch the television on
again. Before disconnecting the data
medium, the television must first be
switched to standby, otherwise files can
be damaged.
Note: »USB1« interface of the television
supports 500mA current according to the
USB standard. Devices such as external
hard disk and etc. that consume more
power can only be connected to the
»USB2« interface of the television.
If you are using a power cable for the
external hard disk that you have
connected to the »USB2 (HDD)«
interface, then the power cable of the
external hard disk must also be
unplugged when the TV is turned off.
You must not disconnect the USB Device
from the TV while a file on the USB Device is being read by the TV.
A bi-directional data transfer as defined for ITE (Information Technology Equipment) devices
in EN 55022/EN 55024 is not possible.
USB transfer is not an operating mode in itself. It is only an additional function.
USB recording settings:

1. Open the menu with ≫MENU≪ button.

2. Using ≫V≪ or ≫Λ≪ buttons, select ≫USB RECORD≪ menu and confirm with ≫OK≪.
3. ≫USB RECORD≪ menu is displayed

September 2012 50
 J5 CHASSIS / TELEVISION

5.8. DivX VOD

DivX® is a digital picture format created by DivX, Inc. This is a DivX

Certified® device that plays DivX video. For more information to
convert your files to DivX image files and for software tools, please
visit divx.com.
DIVX VIDEO ON DEMAND, To play DivX Video-on-Demand (VOD)
films that you purchase, you should have this DivX Certified® device registered. To receive
your registration code, navigate to your device’s USB settings menu and DivX VOD section.
For more details about registration, please visit the address vod.divx.com.

5.9. DIGILINK & CEC Feature

Your television is equipped with DIGI LINK feature. This feature

utilizes CEC (Consumer Electronics Control) protocol. CEC allows you
to make an HDMI connection between your TV and DVD player, STB
or video recorder and control such equipments with the remote control
of the television. This feature must also be supported by the device
you connect.

Switching on the external device from standby mode:

When you switch on your external device (e.g. DVD player) from standby mode, your
television will be turned on from standby mode as well and it will switch to the HDMI source
that the external device is connected to.

Selecting the HDMI source from the television:

When you switch on your external device (e.g. DVD player), your television will switch to the
HDMI source that the external device is connected to. (your television must be on).

Selecting menu language

When you select menu language on your TV, menu language of the external device will
change as well. (If your DVD player supports)

Switching off the device from standby mode

After switching your television to standby, your external device (e.g. DVD player) will also
switch to standby if it is switched on.

September 2012 51
 J5 CHASSIS / TELEVISION

6. EXTERNAL DEVICE CONNECTION

Connecting external equipment via SCART socket

Rear view of product

SATELLITE RECEIVER

GAME CONSOLE

Connecting external equipment via S-Video socket

Side view of product CAMERA

SATELLITE RECEIVER

GAME CONSOLE

Connecting external equipment via YPBPR sockets

Rear view of product

Audio connection

Video connection
September 2012 52
 J5 CHASSIS / TELEVISION

Connecting external equipment via HDMI socket

SATELLITE RECEIVER

GAME CONSOLE

Rear and side view of product

Connecting digital amplifier / AV receiver via Optical Out or SPDIF socket

Optical Connection

DIGITAL AMPLIFIER

SPDIF Connection

Rear and side view of product

Connecting AV receiver via Audio Out L/R

Audio Connection AV RECEIVER

Rear view of product

September 2012 53
 J5 CHASSIS / TELEVISION

PC connection

Rear view of product

Audio connection

Video connection

Inserting CI (Common Interface) card

of
e view of product
Side view

September 2012 54
 J5 CHASSIS / TELEVISION

7. GENERAL OPERATING PRINCIPLE OF TV

September 2012 55
 J5 CHASSIS / TELEVISION

7.1. Chassis General Operating Principle

100Hz URSA circuit is not used as an external circuit, but it is integrated to the main
integrated circuit in products with J5 chassis, unlike the products with TP chassis.
As shown in block diagram, single integrated circuit is used for digital and analog controls in
J5 chassis as well as in our other digital chassis. Besides, DVB-T/C and analog
modulator/demodulator are integrated in the main IC. DVB-S/S2 and DVB-T/T2
demodulators are separate from the main IC. The signals from all audio and video sources
provide input to the main integrated circuit; after the video has been processed, it is sent to
the panel from the integrated circuit via LVDS lines. Likewise, the sound is sent to the audio
amplifier after being processed. DDR3 RAMs are used for main IC and MEMC circuit's
processes.

September 2012 56
 J5 CHASSIS / TELEVISION

While performing these processes, the main integrated circuit reads software installed on
integrated flash and EEPROM data installed on EEPROMs. RAMs are used for the
processes performed within the integrated circuit.

Surely, the system should be supplied power in 5V, 3.3V, 1.8V, 1.05V, 2.5V and 1.2V, which
is required for these processes.

7.2. DC Power Stage

The Chassis and supply unit are connected via S106 connector. In J5-chassis products, only
5V is fed from the supply unit (PSU) in Stand-By mode (+5V2_ST). 12V and 24V supplies
are switched on by the control of main integrated circuit when television is going out of
Stand-By.

September 2012 57
 J5 CHASSIS / TELEVISION

On S106 connector, 3 main control signals are sent to the power supply. The first signal is
“POWER_SWX”; it is sent to the power source from 13th pin of S106 connector. It switches
on 12V and 24V voltages in the "ON" status. 2. The second signal is “BL_CTRLX”; it
switches panel's backlights on or off. This signal is sent from the 19th pin of S106 connector
to the power supply and from there, to panel inverter. 13. In cases where 13th leg is high
(3.3V), backlights are switched on. 3. The third signal is “BRI_ADJX”; it is sent from the 17th
pin of S106 connector to supply unit, and from there to panel inverter. BRI_ADJX signal
represents DIMMING in our previous chassis; it determines the brightness level of backlight
depending on the value set in the user menu. When BRI_ADJX is high (3.3V) maximum
brightness level is reached. This signal can be a square wave or a DC value according to the
panels using PWM dimming and DC dimming.

In Stand-By mode, only +5V2_ST, +5V2_ST_A, VCC3V6-ST (IC108), VCC3V3S (IC107) and
VCC3V3-ST (IC113) voltages exist on chassis. These volatges are used for core voltage
supplies of various modules and ICs as you can see in the electrical diagram of J5. In Stand-
By mode, integrated circuits and regulators remain off as long as possible to ensure lower
power consumption. In J5-chassis products, Stand-By power consumption is below 0.5W.

“POWER_SWX” signal sent from the main IC makes the device exit Stand-By mode. With
POWER_SWX signal; 12V and 24V voltages of PSU are turned on; and POWER_SW
control signal turns on VCC3V6-ST-B (IC122) and VCC3V3 (IC110) voltages respectively.
VCC3V6-ST-B signal activates IC114 to obtain VCC2V5. VCC3V signal activates IC102 and
IC103 regulators, and VCC5V and VCC1V25T2 voltages are obtained. VCC2V5 signal
activates IC100 regulator and VCC1V5 is obtained. PG2 (power good) signal is obtained
from the leg nr. 5 of the IC100 regulator.
PG2 control signal activates IC112 to obtain VCC1.15V. PG1 signal taken from the leg nr. 5
of IC112 regulaor activates IC121 and IC104 to obtain VCC3V6-ST-A and VCC3V3T
voltages.

12V PANEL-VCC voltage is controlled by means of switching T100 with TCON_ON signal
sent by main integrated circuit.

VCC1V5 voltage provides supply for DDR3 RAMs (including Ursa RAM) and main IC;
VCC2V5 voltage for main IC and DVB-T2 demodulator; VCC1V25S2 voltage for and DVB-S2
demodulator; VCC1V25T2 voltage for DVB-T2 demodulator; VCC3V3 voltage for EEPROMs,
main IC, NAND flash, DVB-T2 demodulator, DVB-S2 demodulator, I2C pull-ups and RESET
integrated circuit.

24V VCC_AUDIO voltage provides supply for audio and subwoofer amplifier.

VCC5V voltage supplies tuner , VGA and USB; 3.3V_Tun voltage supplies HDMs; and
VCC1V2_FE, VCC2V5_FE and VCC3V3_FE_SAT voltages supply DVB-S2 demodulator.

September 2012 58
 J5 CHASSIS / TELEVISION

8. OPERATING PRINCIPLES OF CIRCUIT COMPONENTS

8.1. Circuit components on the chassis

IC400, IC-SMD MSD8881CV-WOY PBGA TRAY Main IC:

Main integrated circuit IC100's specifications: Digital (DVB-T/C) and analog broadcasting
demodulator, USB recording, Broadcast and A/V d(NTSC/PAL/SECAM) Full HD 100Hz
support, MPEG-2 and MPEG-4 support, 32-Bit Linux based processor, Sound and subwoofer
processor and interface, 2 USB, 4 HDMI, 2 DDR3 RAM.

Main integrated circuit collects and processes data coming from all inputs and sends audio
and video output to the speaker over amplifier and to the panel over LVDS line. This
integrated circuit has more than 500 legs. Special equipment is required for installation and
removal. Therefore, these integrated circuits are designed with very low error ratios. If you
suspect any error with main IC on TV, firstly supplies of this IC should be checked. There are
5 input supplies as 1.15V, 1.5V, 1.8V, 2.5V and 3.3V. Extremely low or high ratings of these
supplies might cause image freezing, some sources' not functioning or losing the picture
completely. Besides, the problem might be originated in software, EEPROM, flash, crystal or
RAM. If there is a problem, we cannot be sure that it is originated in IC before checking it out.

September 2012 59
 J5 CHASSIS / TELEVISION

While turning the TV on, main IC switches on the system by reading the flash and turns on
the power supply by switching the “POWER_SWX” signal to high. Then, panel signals
“BRI_ADJX” (Sets backlight brightness), “TCON_ON” (turns on Panel TCON board, panel
supply) and “BL_CTRLX” (turns on backlight) turn on panel backlight and the image appears
on TV.

IC303, IC-SMD APX812-29UG-7 SOT143 , RESET IC

When VCC3V3_ST voltage falls below 3.08V, System-RST signal is sent to the main IC and
the system is reset.

IC401, IC-SMD M24C64-WMN6TP-K SO8, EEPROM (PANEL DATA)

Panel EEPROM contains the panel’s electrical values obtained after panel adaptation as well
as the resolution data and white settings of the panel. This EEPROM also includes HDCP,
i.e. HD broadcast copy protection password. In case of failure, copy protected HD
broadcasting cannot be received.
Panel EEPROM file is named as “Panel.bin”. This EEPROM’s power supply is 3.3V. If TV
panel does not respond to software update, it should be changed. Its size is 64Kbits.

September 2012 60
 J5 CHASSIS / TELEVISION

IC403 , IC-SMD W25Q16BVSSIG SOIC8, SPI FLASH

Similar to TP chassis, J5-chassis products also have two types of software. Similar to BIOS
software on the computer, "Bootloader code" starts to operate as soon as TV is energized
and ensures the functioning of system software. Bootloader code software is stored in SPI
flash, which is used on IC403 position. Its size is 16 Mbits.

September 2012 61
 J5 CHASSIS / TELEVISION

IC500, IC501, IC502 IC IC-SMD K4B2G1646E-BCK0 FBGA, DDR3 RAM:

RAM is the place where main integrated circuit performs the processes such as decoding,
encoding, image and video resolution in all applications. Similar to a calculator, it constantly
carries out the processes to ensure the operation of TV. RAM supplies should be carefully
checked. Fluctuations in RAM supplies may cause various errors. Sudden rise or fall of RAM
supply might freeze the television and cause picture lagging.

IC304, IC-SMD K9F4G08U0D-SCB0 TSOP, NAND Flash

Flash memory is where the system operating software is installed. 4GBit nand flash on IC304
position is used in J5 chassis.

System software starts to operate as soon as TV is turned on. This software installed in the
flash controls all TV functions.

If any problem occurs in the flash integrated circuit, the chassis will not function because the
software in the chassis does not start. As soon as the chassis is energized, LED located on
the front panel will start flashing. This means that main IC has read and started the software.
IF LED is constantly illuminated but not flashing, and the chassis is not turned on even
though it is energized, this means either software was not read due to a problem in flash IC
or it could not be started due to a problem in main IC.

September 2012 62
 J5 CHASSIS / TELEVISION

IC800, IC-SMD STA381BWTR-5HUF VQFN48 , Audio and Headphone Amplifier:

The integrated circuit of audio amplifier amplifies digital audio data coming from main IC to
the desired level and sends it out. J5 chassis’ audio output is 2x10W. 55" product's audio out

September 2012 63
 J5 CHASSIS / TELEVISION

power is 15 W (8 ohm), whereas all other products have 10W (8ohm) audio out power in J5
chassis products. A separate circuit for headphone output is not designed in J5 unlike the TP
chassis. Headphone amplifier is integrated to audio IC. Service menu headphone setting can
be set as STA to activate this feature. Headphone audio output power is “2.5mW±10% &
THD+N Ratio: 1%” for -12dBFS, and “≤ 40mW & THD+N Ratio: 10%” for 0dBFS. IC800
audio amplifier is supplied by 24V VCC_AUDIO voltage. A dedicated circuit is used to avoid
POP NOISE when the TV is turning on and off.

IC802, IC-SMD STA381BWTR-5HUF VQFN48 , Sub Woofer

Sub Woofer is optional in J5-chassis products. IC800 audio amplifier is supplied by 24V
VCC_AUDIO voltage.

September 2012 64
 J5 CHASSIS / TELEVISION

IC203, IC-SMD MSB1231-LF LQFP64 DATE-1051, DVBT2 Demodulator:

DVBT2 demodulator enables the reception and modulation of next generation digital
terrestrial broadcasting (DVBT2), and the creation of audio and video. For DVBT2 modulated
broadcasts to be received by J5-chassis product, DVBT2 should be selected ON in service
menu in addition to lineup of DVBT2 modulator and peripheral components on the chassis.
DVB-T2 demodulator’s supplies are 1.2V, 2.5V and 3.3V. IC203 communicates with main IC
and tuner through I2C lines.

IC202, IC-SMD W25X10BVSNIG SOIC8, DVBT2 SPI Flash:

It is the integrated circuit where the software running DVB-T2 processor is installed. It is
supplied with VCC3V3 voltage.

September 2012 65
 J5 CHASSIS / TELEVISION

IC201, IC-SMD CXD2850AER-T4 QFN, DVB-S2 Tuner and Demodulator IC:

S2 Tuner and Demodulator are used in the same IC in J5-chassis project unlike the TP-
chassis. The satellite receiver obtains inter frequency signal of digital broadcast taken from
the tuner, filters this carrier frequency from other frequencies and sends video and audio
data on it to the demodulator after loading IF on inter-frequency. DVB-S2 compatible tuner
also enables viewing HD broadcast from the satellite. It operates with 1.2V, 2.5V and 3.3V
supplies. And its outputs are directly sent to the demodulator.

IC201 is also the S2 demodulator (decoder) integrated circuit. Digital broadcast (D_IF)
selected from DVB-S2 tuner enters demodulator IC. Demodulator integrated circuit receives
video and audio data loaded on the carrier frequency and this data is separated from the

September 2012 66
 J5 CHASSIS / TELEVISION

carrier frequency and converted to the form required for transmission to the main IC. For the
efficient transmission of the signal, digital image is sent to the main integrated circuit as
transport stream. DVB-S2 compliant IC is used for the SONY CXD2850AER demodulator
used in J5-chassis products.

IC116, IC-SMD LNBH25LPQR QFN24, LNB regulator

This integrated circuit adjusts LNB voltage according to the data received from IC through
I2C line. High band-low band, vertical-horizontal selection, DiSEqC selection are all done
according to the data this integrated circuit sends to LNB. It is supplied 12 V power. As 12V
power is only used to feed this integrated circuit in satellite module and as "Enable" signal
when generating 3.3V, we may estimate that any error in 12V will affect this IC.

IC301, IC-SMD AP2171WG-7 SOT23-5, PCMCIA Current Limitation

It is the integrated circuit that switches VCC-PCMCIA supply voltage and limits the current to
1A.

September 2012 67
 J5 CHASSIS / TELEVISION

IC100, IC-SMD TPS54326RGTR QFN , VCC1V5 Step-Down Convertor

It is the step down converter that switches 1.5V from 5.2V. It is used for 1.5 V DDR RAM
supply and in the input of the regulator where 1.25V is obtained. Max 1900 mA current can
be drawn from IC100.

IC103, IC-SMD XC6602A121ER-G USP-6C , VCC1V25T2 LDO Regulator

IC113, IC-SMD XC6222A331ER-G USP-6C, VCC3V3-ST LDO Regulator

This is the LDO regulator that allows obtaining VCC3V3-ST from VCC3V6-ST.
Max 280 mA current can be drawn from IC113.

September 2012 68
 J5 CHASSIS / TELEVISION

IC108, IC-SMD HPA011146RGTR QFN, VCC3V6-ST LDO Regulator

This is the LDO regulator that allows obtaining VCC3V6-ST from +5V2_ST.
Max 1190 mA current can be drawn from IC108.

IC104, IC-SMD XC6222A331ER-G USP-6C, VCC3V3T LDO Regulator

This is the LDO regulator that allows obtaining VCC3V3T from VCC3V6-ST.
Max 290 mA current can be drawn from IC104.

September 2012 69
 J5 CHASSIS / TELEVISION

IC114, IC-SMD XC6222C251ER-G USP-6C, VCC2.5V LDO Regulator

This is the LDO regulator that allows obtaining VCC2V5 from VCC3V6-ST-B.
Max 301mA current can be drawn from IC114.

IC120, IC-SMD XC6602A121ER-G USP-6C, VCC1V25S2 LDO Regulator

This is the LDO regulator that allows obtaining VCC1V24S2 voltage from VCC1V5. It is used
for S2 Tuner and Demodülatör IC supplies.
Max 500 mA current can be drawn from IC120.

September 2012 70
 J5 CHASSIS / TELEVISION

IC112, IC-SMD TPS54326RGTR QFN , VCC1.15V LDO Regulator

This is the LDO regulator that allows obtaining VCC1.15V voltage from +5V2_ST. It is used
for IC core supplies. Max 3108mA current can be drawn from IC112.

IC109, IC-SMD AP2171WG-7 SOT23-5, USB Driver IC (Rear USB)

IC109 serves as current limiting and supply integrated circuit for USB. 1000 mA nominal
current can be drawn from this integrated circuit.

September 2012 71
 J5 CHASSIS / TELEVISION

IC111 and IC105, IC-SMD AP2171WG-7 SOT23-5, Wi-Fi module driver IC

IC111 serves as current limiting and supply integrated circuit for Wi-Fi module. 500 mA
nominal current can be drawn from this integrated circuit.

IC106, IC-SMD AP2171WG-7 SOT23-5 , SIDE USB driver IC

IC106 serves as current limiting and supply integrated circuit for SIDE USB. 1000 mA
nominal current can be drawn from this integrated circuit.

September 2012 72
 J5 CHASSIS / TELEVISION

IC700,IC701,IC702,IC703, IC-SMD CAT24C02TDI-GT3A TSOT23-5, HDMI Eeprom

HDMI EEPROMs contain information related to the ports which are used for video and audio
inputs. These are HDMI 1, 2, 3 and 4 EEPROMs where the information on definitions and
contents supported by the product and EDID data is stored.

September 2012 73
 J5 CHASSIS / TELEVISION

IC601, IC-SMD MAX9820ETB+T TDFN, Scart Audio Amplifier

IC601 is the audio amplifier used to enhance scart audio output signal.

IC600, IC-SMD CAT24C02TDI-GT3A TSOT23-5 , VGA Eeprom

When VGA cable of the computer is connected to TP chassis, VGA EEPROM at position
IC901 contains the information about the supported picture format. The broadcasts other
than this resolution (for example 720P) may not be shown. Besides, IC600 contains EDID
DATA information where resolution data of TV and PC connected at VGA input is compared.

September 2012 74
 J5 CHASSIS / TELEVISION

IC803, IC-SMD MAX9820ETB+T TDFN , Chinc connector audio output amplifier

It is the audio amplifier used to increase Chich connectors’ audio output.

TU200, TUN SUT-RE216 DVBT&C DIK SONY, Tuner

J5 chassis utilizes hybrid tuner. Receiving both analog and digital broadcasts from the cable,
the tuner obtains analog and digital IF (inter frequency signals) of the broadcasts. This SONY
brand tuner uses 5V power as antenna feed for active antennas. This selection can be made
from user menu and is controlled by the signal on D200 from the chassis (Leg 1). Tuner is
locked to the desired channel by communicating with main board and main IC, depending on
the selected source, through T_SCL and T_SDA lines. It selects the desired frequency by
filtering other frequencies and transforms the signal as to enter main IC. This chassis does
not have a separate demodulator IC. Demodulation is performed in main IC. Here, I2C

September 2012 75
 J5 CHASSIS / TELEVISION

protocol is used for the purpose of communication (Leg 3 and 4). Tuner's own power supply
is 3.3V (Leg 2).

Legs no. 7 and 8 are used for external T2 demodulator connections. IF_AGC output is given
in leg no. 9.

September 2012 76
 J5 CHASSIS / TELEVISION

9. SERVICE MENU SETTINGS

To enter service menu, just like in the previously launched products, we press menu button
of the remote control and enter 9, 3, 0, 1 or 8, 5, 0, 0.

As the chassis improvement and development works go on throughout the production,

service menu items may vary according to the software version. The following explanations
are service menu settings of the current version.

System Configuration:

This menu contains general settings of the system. Press OK button on the remote
control to access this menu.

TV MODE tab contains "Factory" and "Customer" options. It is used to perform factory
controls and settings more efficiently and faster. On the TVs delivered to the customer, this
setting is absolutely selected as "Customer." Otherwise, it will lead to customer complaints
such as "TV automatically turns on after power failures" or "different functions operate from
the remote control".

HDCP VERIFY: It must be checked if HDCP key is loaded or not during factory controls.
HDCP key stands for ““High Bandwidth Content Protection Key”. This key is used to prevent
copying of data on digital sources such as DVD or blue-ray. With HDCP, video data is
transmitted from the source to the receiver as encrypted. Therefore, to watch HDCP
encrypted DVDs or blue-ray, HDCP key should have been loaded on TV. On the products
with HDCP installed, SUCCESS message is included.

DEBUG MODE is the feature, which is used to track software modifications made on TV
during R&D stage. This setting must be "Off" on TVs delivered to the customer.

PLUG PLAY (Demo Mode): A navigation key is pressed after having completed all settings
and checks in the factory. Later, "Please wait" message appears; and when you see the
message "DONE", the device should be unplugged and plugged again. With this process,
television will be set to its initial values before delivery. It will be proper to set Plug&Play tab
after servicing. After pressing right key on the tab, EEPROMs will be loaded with factory

September 2012 77
 J5 CHASSIS / TELEVISION

defaults. TV can be shipped to the customer after this setting. Please note that any warning
is not displayed or you do not have to exit the menu while Plug&Play is getting activated. You
should be careful not to take the device into Plug&Play mode by mistake.
BLUE BACK enables us to determine background when there is no picture on the screen.
When "On" is selected, background will be blue; and when "Off" is selected background will
be black or snowing. “On” should be selected in GRUNDIG brand products and “Off” in other
products.

HOTEL tab should be set to "On" with the products for which Basic Hotel TV feature is
desired; and it should be set to "Off" in other products. When the hotel model is "On", certain
features designed for the hotel use are activated; the user cannot change the channels set
by the service, for example, or the volume cannot be increased more than a certain level.
(For detailed information, refer to 16. HOTEL TV SETUP)

CI KEY VERIFY indicates if CI Key was installed or not. This menu cannot be changed. This
option should appear as “Pass” in the products with CI Plus feature. CI Key is the keyword
on the card which is inserted to decrypt the broadcasting. This menu is a control indicator
and changes automatically. This keyword is installed during TV production and it becomes a
kind of ID for your TV when watching encrypted channels. J5-chassis products support CI+
feature. Launched in 2008, it is a new encryption standard developed with the collaboration
of consumer electronics and scrambled digital broadcasting companies. It was possible to
copy the programmes after decoding process; however, now they cannot be copied because
IC that comes with CI Plus has a key. In this system, broadcasting is initially decoded on CI
card. The broadcasting transmitted to the main IC from the CI card is also encrypted and it is
decoded with CI Key, which is a factory setting and different for each TV. Thus, there will be
no free encrypted broadcasting on the bare line and encrypted broadcasting cannot be
copied. CI+ feature is standard in all the products with J5 chassis.

PANEL ENERGY CLASS header is used for selecting the energy class of the product.
Product is set to specifications in the factory. Panel brightness levels available in the panel
EEPROM are used according to the product energy class.

September 2012 78
 J5 CHASSIS / TELEVISION

SOURCE Configuration:

This menu can be accessed by pressing 2,3,5,6 on the remote control. The settings under
source configuration tab determine which sources will be on and which ones will be off
depending on customer demands. In J5-chassis products, only SATELLITE is optional and
DVD source is not supported. All other sources are set to ON in standard.

TV Configuration:
This menu contains configuration settings of TV. We may select amongst the menus that are
being used and to be used on TV. These settings differ from the "System Configuration". This
menu contains the changes which the user can directly observe.

To enter this menu, you should go to "TV configuration" from the service menu and enter the
numbers 2, 3, 5, 6 in sequence.

September 2012 79
 J5 CHASSIS / TELEVISION

DVBT2 (Next generation digital terrestrial broadcasting modulation) is selected as ON/OFF,

depending on the customer preference, in the countries that support DVBT2 digital terrestrial
broadcasting. DVBT2 is selected OFF in the products to be used in the country. In our
country, TRT makes DVBT2 test broadcasting in Ankara. It should be selected in other
products according to the customer’s demand.

OSD SELECTION menu has "Grundig", "Beko", "Arçelik" and "OEM" selection. For Grundig
products, “Grundig” is selected. Menu images differ according to the brand selected.

USB RECORDING (GRFset1) menu indicates the television's status of USB recording. In J5-
chassis products, it is selected ON by default. It will be off in Non-pvr products.

REMOTE CONTROL GRUNDIG and other OSDs can support several different models of
remote controls and all those models can be viewed under the menu. Selection of remote
control may vary according to the customer demand.

KEYPAD enables you to select keypad according to the mechanical structure of the product.
4-Key, 6-key, single-key and “Joystick” options are available. If selected wrong, the keys will
work in different functions. In J5-chassis product, 6+1 keypad module is selected as
standard.

MEMC stands for "Motion Estimation Motion Compensation." It should be selected “On” with
all products.

7 SEGMENT DISPLAY is the LED that mechanically shows the time on the front panel. In
J5-chassis products, it is selected OFF.

ECO TV ensures eco standards-compliant power consumption by turning down the backlight
a bit when it is selected "On". ECO TV option should be selected ON for all products with J5
chassis.

LINE OUT (LEFT/RIGHT Audio output) tab should be selected “ON” if it is available on the
product. In J5-chassis products, LINE OUT feature will be available as standard.

HEADPHONE tab allows setting of headphone socket on TV. Headphone setting in J5-
chassis shall be selected as “STA”; STA selection shows that headphone output is taken
from the available audio amplifier.

SHOP MODE is used in the first installation at the dealers for purposes of display (Shop
Mode and Home Mode screens appear). When Shop Mode is selected, the logos of various
features such as CI+, SRS etc., which are supported on TV, appear on top of screen with
certain intervals. SHOP MODE should be selected ON for all products. However, when the
product is delivered to the customer, TV is switched back to factory settings via PLUG PLAY;
and HOME MODE is selected during the first installation at the customer’s place. During the
first installation, SHOP MODE is only selected at the dealers for the purpose of display.

3D TV (3 Dimensional TV Technology) feature shall remain as "ON" in J5-chassis products.

CEC feature allows you to make an HDMI connection between your TV and DVD player,
satellite receiver or video recorder and control such equipment with the remote control of the
television. The products with J5 chassis have CEC feature as standard.

SPEAKER OUTPUT POWER is used to select audio output power. In J5-chassis products,
audio output power should be selected “10W 8 Ohm” as standard. "15W 8 Ohm" shall be
selected for 55” products only.

September 2012 80
 J5 CHASSIS / TELEVISION

SUBWOOFER OUTPUT POWER shall be selected “10W 8 Ohm” as standard in J5-chassis

products.

HIDEV MONO (improvement of high audio deviation), is a feature developed to prevent

imbalances that may occur on sound carrier signals due to high audio deviation in the
country. It is ON for domestic products and OFF for the products sold abroad.

OPTIC OUT (Digital Optical Audio Output) feature is generally used to input digital audio to
devices such as amplifier, DVD and etc. OPTIC OUT should be selected ON as standard in
J5-chassis products.

SPORT MODE tab is designed for Grundig TVs with sports feature. It should be selected
“Off” for J5-chassis products.

EPG PADDING TIME Early start and late end times according to the schedule on EPG table
can be set during the installation of PVR. It will be off in Non-pvr products.

BISS KEY tab is designed to decode the coded broadcasts via satellite without using a
module. It should be selected “On” for J5-chassis products.

GRFset2 tab is used for design purposes. It should be selected “On” for J5-chassis products.

UART ENABLE Some debug outputs are turned off to allow faster operation of the TV. When
it is selected as “ON”, you can see that it provides more outputs when a serial connection via
VGA to TV is made. It should be selected “Off” for J5-chassis products.

VOICE RECOGNITION RC tab is for voice controlled remote. It should be selected “On” for
J5-chassis products.

HBB TV tab is to turn the HBBtv feature on. It should be selected “On” for J5-chassis
products.

POWER LED BRIGHTNESS LOW tab allows setting of the LED brigthness while the TV is
on. It should be selected as “4” for J5-chassis products.

POWER LED BRIGHTNESS HIGH tab allows setting of the LED brigthness while the TV is
off. It should be selected as “9” for J5-chassis products.

CHECK SOURCE AVAILABILITY tab “Highlights” the icons of sources used when it is turned
ON.

PERMANENT TIMESHIFT turns on/off the 60-minute continuous recording feature.

BACKGROUND DMR turns on/off the Background DMR feature. It allows playing videos,
images over network from products with DMR feature such as Media player.

RECOVERY MODE is used for R&D test puposes, here ON must be selected.

PRODUCT TYPE this is the digi9000 and digi900 selection in shop mode images.
Products without subwoofer internal wifi-module are digi900; and all other products are
digi9000.

JITTER IMMUNITY This is added for test purposes, it shall be selected OFF.

September 2012 81
 J5 CHASSIS / TELEVISION

Cloner Configuration

This menu is used to copy your selections, channel lists, user options, satellite settings and
service menu settings on TV and move them to another TV. Particularly, when installing TV
at the user's home, this feature will save us time as we will not have to tune satellite channels
anew. Cloning can be done from any TV with the same chassis. To enter this menu, you
need to go to "Cloner configuration" from the service menu and enter the numbers 4, 6, 5, 8
in sequence.
Copy selects what and to where we want to copy. TV to USB copies the configuration on TV
to the USB. USB to TV transfers previously prepared channel list, user and satellite settings
to TV.
Copy item is the name of configuration to be copied. Channel/Video Set selection enables
transferring channels, frequencies and favourite lists that were already set. Service Set
enables transferring service menu settings. When installing at the user’s place, this option
should NOT BE CLONED. User Set enables us to transfer user settings (sound, brightness,
TV language and etc.).
Start Cloning option starts the cloning process. Whereas TV to USB takes little time, USB to
TV causes a short interruption of TV imaging. When TV automatically restarts after
installation, its means cloning is completed.

NOTES:
When cloning, you should ensure that both product codes are the same. During both TV to
USB cloning and USB to TV cloning, “ALL" should be selected as Copy item. When cloning
between different product codes, only "Channel/Video Set." section should be copied. After
copying, picture settings of TV may show some differences. TV should be delivered to the
customer after those settings are checked. On User menu, go to “Source Settings” =>
“Program Table” (don't select). Press the keys 4, 6, 5, 8; and cloning menu will be displayed.

September 2012 82
 J5 CHASSIS / TELEVISION

Bootcode Configuration:

In the products with J5-chassis, Bootcode should be updated before software updating if
bootcode version is changed. Boot code update is performed through the steps below. When
this menu is highlighted, enter the menu with OK button on the remote control.

Step 1:
Please copy mboot.bin file into USB memory. (If the memory contains more than one
partition, copy the file into the first partition.)

Step 2:
Insert USB memory to the USB socket on the side of TV.

Step 3:
Wait for 10 seconds for USB memory to be automatically mounted.

Step 4:
Open service menu (MENU+8500 (Grundig)).

Step 5:
In Service menu, select Boot Code Configuration and press OK.

Step 6:
If there is no problem, TV will automatically turn off and restart with new bootloader. If there
is a problem, TV will not automatically restart.

ACOUSTIC MANAGEMENT feature is used to create best audio performance of the cabinet.
Bass/treble settings vary depending on options in the existing cabinets; the options have
been adjusted to prevent cabinet resonance and ensure best audio quality.

Software Version

All versions of software and hardware can be seen under software version tab. “URSA
version” tab is the 100Hz software version installed on 100Hz TVs. This menu is for
information only, it cannot be changed.

September 2012 83
 J5 CHASSIS / TELEVISION

APPROVED LOGOS represent the logos to be displayed on the screen, when selected in
SHOP mode.

Standard LOGO displays shall be as below.

DIGI 9000

September 2012 84
 J5 CHASSIS / TELEVISION

SMART INTERACTIVE 2.0

EASY REMOTE

September 2012 85
 J5 CHASSIS / TELEVISION

SOUND BOOSTER (SRS STUDIO SOUND HD)

3D

September 2012 86
 J5 CHASSIS / TELEVISION

USB RECORDING

SRS HD STANDARD

CI+ STANDARD

DLNA Wifi STANDARD

Dolby Digital Plus STANDARD

September 2012 87
 J5 CHASSIS / TELEVISION

Divx+ HD STANDARD

HDMI STANDARD

skype

APPROVED LOGOS: The logos below are displayed if approved by test results.

Cable Ready

YouSee

UPC
Ziggo
MediaSet

Comhem

Spain TDT

Stofa

September 2012 88
 J5 CHASSIS / TELEVISION

Boxer

Riks TV

Canal Digital

TNT HD

Antenna HD Ready

Levira

Other Menus:

Other menus are closed to authorized services as they are used for R&D studies in the
factory.

September 2012 89
 J5 CHASSIS / TELEVISION

10. CUSTOMER SETTINGS

In J5-chassis products, many of the features are selected ON by DEFAULT.

The values of each feature are shown in the next column of the table. The values of optional
features are stated in VTF (Version Demand Form) depending on the customer’s demand.

Customer settings are not changed when software or bootcode is installed.

!! If flash IC is required to be changed in J5-chassis products for any reason at the service
centre, relevant settings should be performed in service menu by re-checking the tables
below and VTF of the product before delivery to the customer because the values in the
tables below will take default values on software in accordance with the product size (screen)
and features!!

Features J5 SW DEFAULT OPT-STD

TV MODE (Customer) CUSTOMER
HDCP VERIFY (Success) SUCCESS
DEBUG MODE (OFF) OFF
PLUG PLAY (OFF) OFF
BLUEBACK (GRUNDIG:ON) OFF OPT.
HOTEL OFF (SIMPLE OTEL TV) OFF OPT.
CI KEY VERIFY (Success) SUCCESS (CI+)STD.
Panel Energy Class (VTF) Default OPT.
ATV (AVAIL) AVAIL STD.
ANTEN (AVAIL) AVAIL STD.
KABLO (AVAIL) AVAIL STD.
SATELLITE (VTF) AVAIL OPT.
USB (USB 2.0) (AVAIL) AVAIL STD.
PC (AVAIL) AVAIL STD.
HDMI1 (AVAIL) AVAIL STD.
HDMI2 (AVAIL) AVAIL STD.
HDMI3 (AVAIL) AVAIL STD.
HDMI4 (AVAIL) AVAIL STD.
AV1 (AVAIL) AVAIL STD.
AV2 (AVAIL) AVAIL STD.
COMPONENT (AVAIL) (YPbPr) AVAIL STD.
S-VHS (AVAIL) (SCART) AVAIL STD.
DVBT2 (VTF) ON OPT.
GRFSET1 (VTF) ON nonPVR-OFF
OSD SELECTION (VTF) GRUNDIG OPT.
UZAKTAN KUMANDA (VTF) TP7 OPT.
KEYPAD (6 BUTTON+1 STD ) 6 BUTTON+1 STD STD.
MEMC (ON) ON STD.
7 SEGMENT (OFF) OFF STD.

September 2012 90
 J5 CHASSIS / TELEVISION

ECO TV (ON) ON STD.

LINE OUT (ON) ON STD.
KULAKLIK (ON) STA STD.
MAĞAZA MODU (ON) ON STD.
3D TV (ON) ON STD.
CEC (ON) ON STD.
SPEAKER OUTPUT
POWER (VTF) 10W@8ohm OPT.
SUBWOOFER OUTPUT
POWER (VTF) 10W@8ohm OPT.
HIDEV MONO (OFF) OFF OPT.
OPTIC ÇIKIŞ (ON) ON STD.
SPOR MODU (OFF) OFF STD.
BISS Key (ON) ON STD.
EPG Padding Time (VTF) ON Non-pvr-off
GRFSet2 (Rovi patent) (ON) ON STD.
Uart Enable (OFF) OFF STD.
Voice Recognition RC (ON) ON STD.
User Default Apps (OFF) OFF STD.
HBB TV (ON) ON STD.
Power LED Brightness 4
Low (4) STD.
Power LED Brightness
High (9) 9 STD.
Check source availability (OFF) OFF STD.
Permanent Timeshift (VTF) OFF OPT.
Background DMR (ON) ON STD.
Panel
GAMMA Panel MAIN SCALER Adaptasyon
Recovery Mode (ON) ON STD.
Product Type VTF Digi900- digi9000 Opt.
Jitter Immunity (OFF) OFF STD.
Panel
MIRROR OFF OFF Adaptasyon
MEGA DCR (Panel Panel
Invertor altında) (ON) AÇIK Adaptasyon
ACOUSTIC
MANAGEMENT Oto
MPEG4 Boxer OFF OPT.
Riks TV OFF OPT.
Canal Digital OFF OPT.
TNT HD OFF OPT.
Com Hem OFF OPT.
Cable Ready OFF OPT.
Antenna HD Ready OFF OPT.
YouSee ON OPT.
UPC OFF OPT.

September 2012 91
 J5 CHASSIS / TELEVISION

Ziggo OFF OPT.

MediaSet OFF OPT.
Levira OFF OPT.
Spain TDT OFF OPT.
Stofa ON OPT.
Digiturk OFF OPT.
PPR/Hz Selection PPR OPT.

September 2012 92
 J5 CHASSIS / TELEVISION

September 2012 93
 J5 CHASSIS / TELEVISION

11.FAILURE ANALYSES
11.1. Sound but no picture, and backlight illuminated

In this section, we will basically explain where we need to check if there is "no picture
on TV" even though there is not any problems in the panel inverter. here, we are
assuming that chassis is generally in good condition as we obtain sound output from
TV.
When you cannot determine if the backlight is working or not due to the illumination
level in the environment, you are recommended to tap on the TV's front panel lightly;
if the backlight is working, you will notice a slight glowing.

Before starting controls and repairs, it is crucial to analyse and comprehend the
problem exactly. In this problem, you must make
sure if it is originated from the utilized source, if it is a cable connection error or if
utilized devices have any problems or not.

Then, particularly LVDS cable on the chassis should be checked for any
disconnections, loose parts, dislocations, breaks or ruptures. Likewise, it will be
proper to check cable connections around the panel.

Later, the panel power supplied to the panel T-CON board over LVDS cable should
be checked. Panel power is 12V on 26" and larger TVs with J5 chassis

If this value of power supply does not exist, the root cause is detected by tracking
back from this supply.

Panel supply is switched by T100 MOSFET. Initially, the input - that is L100 coil - is
checked for 12V. If you cannot detect 12V supply here as well, then the problem is
on the power supply side.

If 12V exists at the input, check the voltage on T100 FET legs. When TV is "ON",
FET Leg 1 has voltage higher than 0V, that is 3.8V, and Leg 2 transmits supply
voltage to Leg 3. If Leg 1 does not have voltage, check "Panel_ON-P1" signal, Leg 1
of R103 resistance. here, if the voltage is high, it means that panel supply has not
been turned on from the main integrated circuit or software. This signal remains high
while the TV is going out of Stand-By and gets down to 0V, 1 seconds before the
picture appears on the screen

If the panel is supplied voltage over LVDS, it is most likely that picture information is
transmitted as well. Even if we do not have
any precise control method for information flow over data lines, the voltage is around
1.2V DC as detected by means of a measuring tool. In this case, it is likely that panel
has an error; if possible, it can be checked by using a different panel or using the
same panel with a different chassis.
Besides, you can also consider problems including that LVDS data is not being
transmitted to the panel properly, wrong panel EPPROM or software error. You can
solve the problem by installing correct software.

September 2012 94
 J5 CHASSIS / TELEVISION

11.2. Sound but no picture, and backlight not illuminated

Even though LVDS data is printed on the screen, the picture cannot be seen
because the backlight is not illuminated. First, cable connections, particularly inverter
and supply cables and connectors should be checked.
24V power supply should be checked over inverter cable when TV is ON. When this
power needs to be supplied to the inverter unit of the panel, the backlight will not be
illuminated if there is not 24V supply. 24V and 12V supplies are switched on by
POWER_SWX signal coming from the main integrated circuit when TV is ON. In this
case, if there is 12V output but no 24V output, then the problem rests in the power
supply.
If 24V supply exists on the system; on the Leg 19 of S106 connector, a voltage over
3V DC should be transmitted to the panel. This voltage gives "switch on" command to
the panel inverter. This control is provided with “BL_CTRL” and peripheral materials.
Besides, voltage level that determines brightness of panel lights through Pin 17 of
connector S106 should be higher than 2V.
Brightness control may vary according to the panel, however, it operates dimly
around 0V and completely on around 3.3V. Brightness control is done by
“BRI_ADJX” signal coming from the main integrated circuit.
When the "backlighting" tab is dimmed in the user menu, the voltage in the Pin 17 of
the connector decreases slowly.
If no problem appears in the checks performed at the chassis, you should consider
that the problem might be arising from panel inverter module or the lights.

11.3.No Sound

It should be checked that if other sources, cables and devices have any problems.
You need to make sure that volume has not been turned down from television
settings or mute button is not pressed.

If there is not any problems, check the loudspeaker cables and loudspeakers on the
chassis; fix the problem, if any.

Check if there is sound on the headphones socket. headphone output is also use
audio amp. In general, getting sound on the headphone socket shows that the
problem rests in the sound amplifier’s output stage (IC800).

Also, if you cannot get the sound on TV, scart output should be checked for the
sound. If there is no sound in the scart output, then it means that there is no sound
coming from the main integrated circuit. If the scart output has sound, the problem
might be arising from the sound amplifier or peripheral materials.

At the IC800 position, 8th and 5th pins of the sound amplifier or L805 condenser is
checked for 24V. If you don't detect this supply, you should make sure that either

September 2012 95
 J5 CHASSIS / TELEVISION

L800 or L806 coil is inserted. If any, as mentioned before, power supply should be
checked for problems.

If the amplifier is being supplied with power, Leg 22, 27,48,38 and 40 on Amplifier
should be checked for 3.3V DC voltage. If 3.3V does not exist, we should check
VCC3V3. This voltage gets down to 0V and ensures switching the amplifier off in
Stand-By mode (AMP_STB signal and main integrated circuit performs the control).

Sound amplifier has I2C communication lines to communicate with the main
integrated circuit. Roughly, the voltage level should be below 3.3V and variable at
the Pins 43 and 44. here, the fixed 3.3V gets lower when data is being transmitted,
and thus, sound amplifier and main integrated circuit communicate. If this value is
constantly 0V, short circuit possibility should be checked where I2C line is
connected. Current version of the software should be installed against software
problems.

Pin 40 is the reset pin of the sound amplifier. This pin should be high (3.3V) during
the time when TV is on. This value might be measured from C843. If this value is low
(0V), RESET_OUT signal should be checked. If this signal, which can be checked
from R820 resistance, is low, you may suspect that the problem rests in software.
If all these inspections don't give any results, you may suspect that amplifier
integrated circuit has failure.

September 2012 96
 J5 CHASSIS / TELEVISION

13. CHASSIS SCHEMATIC

13.1 Schematic

DC socket – S106

LDO (IC100) 1.5V

September 2012 97
 J5 CHASSIS / TELEVISION

LDO 5V (IC102) , 1.25V (IC103)

LDO 3.6V (IC108)

LDO 3.3V (IC104), 2.5V (IC114)

September 2012 98
 J5 CHASSIS / TELEVISION

LDO (IC113) 3.3V

LDO (IC112) 1.15V

September 2012 99
 J5 CHASSIS / TELEVISION

LDO 3.3V (IC110), 3V3S (IC107)

PANEL - VCC

USB - VCC

September 2012 100

 J5 CHASSIS / TELEVISION

BACK USB (HDD)

SIDE USB

September 2012 101

 J5 CHASSIS / TELEVISION

TUŞ TAKIMI

BOOT LOADER

September 2012 102

 J5 CHASSIS / TELEVISION

September 2012 103

 J5 CHASSIS / TELEVISION

DVB - T2

September 2012 104

 J5 CHASSIS / TELEVISION

DVB - S2

ETHERNET

September 2012 105

 J5 CHASSIS / TELEVISION

PCMCIA – POWER

AUDIO ve HEADPHONE AMFI

September 2012 106

 J5 CHASSIS / TELEVISION

SUBWOOFER AMFI

HDMI 1 EEPROM

September 2012 107

 J5 CHASSIS / TELEVISION

HDMI 2 EEPROM

HDMI 3 EEPROM

September 2012 108

 J5 CHASSIS / TELEVISION

HDMI 4 EEPROM

HYBRID TUNER

September 2012 109

 J5 CHASSIS / TELEVISION

13.2 Critical Voltage on chassis

September 2012 110

 J5 CHASSIS / TELEVISION

September 2012 111

 J5 CHASSIS / TELEVISION

14. SOFTWARE UPDATE

14.1 Updating TV Software By Using USB Memory

To update TV software by means of USB memory, we will use Target folder

available in the system according to product code.

Firstly, copy Target folder to USB main directory. Before starting installation, you
should check script, image and panel files in the Target folder which will be
installed.

The content of Target folder to be transferred to USB disk main directory

should be as shown below.

The content of BIN_FILES folder should be as shown below.

Shut down TV before inserting USB to TV for software update. (Disconnect the
power)

Then, insert USB to TV; “P+” key of the keypad on TV and plug the TV.

Hold down any key of the keypad on TV until you see that code installation has

September 2012 112

 J5 CHASSIS / TELEVISION

started.

USB update logo will be shown on the screen during software download from USB.

If code installation has been successfully completed, TV will automatically turn on.

Shut down TV to remove the USB.

14.2. BOOT Code Installation From Service Menu by Using USB Memory

Boot code update can be performed on TV's factory or customer mode.

Boot code to be installed should be in USB memory's main directory with the name
“mboot.bin”. Ensure that software that you downloaded from the system has this
“mboot.bin” file.

USB memory is inserted to TV and TV turns on (without pressing any key), service
menu is opened from the TV. (After entering the menu, type 8500 for GRUNDIG
brand products and 9301 for others)

In Service menu, go to "Boot Code Configuration" menu. (Press green button in

September 2012 113
 J5 CHASSIS / TELEVISION

service menu or OK on Boot Code Configuration tab)

In “Boot Code Configuration” menu's “Start Loading” option, boot code update is
started from left or right key.

If TV's boot code is not updated, "Fail" message appears next to "Start Loading"
menu item. If update is successful, TV automatically restart.

TV should never be shut down during code loading. If TV is shut down, boot code
should be installed by using Debug tool

14.3.Updating Panel Eeprom Using USB Memory

“Panel. bin” file must be located under “BIN_FILES” and under “panel” folder
seen below.

Shut down TV before inserting USB to TV for software update. (Disconnect the
power)

Then, insert USB to TV; “P-” key of the keypad on TV and plug the TV.

Hold down any key of the keypad on TV until you see that code installation has
started.

USB update logo will be shown on the screen during software download from USB.

14.4.MBOOT Installation by means of DEBUG TOOL

This feature should be used when you encounter an error while loading boot code
from USB.

MBoot program of the TV is installed by means of Debug Tool over VGA via
MStar company's ISP TOOL program.

MBoot software can be loaded on TV by using the adapter which had been

September 2012 114

 J5 CHASSIS / TELEVISION

previously used in MStar concept projects.

MBoot can be loaded over VGA Input. USB port is used for PC connection. To load
MBoot on TV, VGA cable is connected to VGA connector that is in the opposite of
USB connector. Software installation adapter has a key. This key enables you to
select the pin configuration (pin: 11,4), the key should be positioned on the USB
connector side.

To be able to use ISP Utility program, MStar Debug Tool's driver should have been
loaded on the PC. ISP Utility can be copied anywhere on the computer and
ISP_Tool v4.5.2.8.SP.exe application is executed.

September 2012 115

 J5 CHASSIS / TELEVISION

When executed for the first time, the program is opened as shown below. Settings
should be selected as in the figure.

Under “Read”, pressing “Read” button shows the location of software to be

installed. Select J5 files.

After selecting software (*.bin) to be installed, press AUTO button. In standard use,

September 2012 116

 J5 CHASSIS / TELEVISION

the following options are recommended.

After completing the settings, please press "Dis Con" button of the program
interface, then turn TV Power Off/On, press "Connect" button within 1-2 seconds. In
this way, TV goes to ISP mode. Here, a message indicates that Device type has
been recognized. If not connected, root cause of problem should be inspected.

After indicating the location of software correctly from READ section, press "Run"
button to start installation. “Erase” process may take 45 seconds. If this process
takes too short after pressing "Run", it might be suspected that there is a problem.

“Verify” process is a must. If there is an error in writing process, most probably this
will be shown within the first 4-5 seconds; you may press "Stop" button before
waiting for the completion of Verify process.

If the installation is successful, "Pass" message appears.

After completing software installation, service menu settings (Eco Mode, Blue Back,
OSD selection, Keypad and TV inputs) depending on TV's features and Plug Play
should be performed before delivering TV to the customer. Plug Play is located in
System Configuration under Factory Settings (Service Menu).

If the programme does not run successfully, it might be resulting from the following
conditions:

There might be a problem in cables, converter or tool. Probably, TV does not

support USB memory that we are using. We should format USB memory with
FAT32 system and re-install software. If this does not work, we should try to install
software using another USB memory.

September 2012 117

 J5 CHASSIS / TELEVISION

On the chassis, there might be a problem arising from components or soldering. On

the PC, there might be problem arising from USB hardware or driver.

The latest version of ISP Utility should be used. MStar Debug Tool driver should be
installed. In “Config”, I2C Speed should have the correct value. In “Device”, “WP
Pin pull to high during ISP” should be selected. If not selected, the software may not
be updated even though it seems to be installed. If Device type is not recognized
even after you perform the steps above, turn off/on TV from the mains.

!!! IMPORTANT NOTE

Before software installation, TV's service menu settings, user (customer)

settings, channel list and satellite settings should be stored in an external USB
memory device by means of USB cloning feature (USB cloning-TV to USB); and
these settings should be re-loaded on the relevant TV after software installation
(USB-cloning USB to TV)!

To enter this menu, you should go to "Cloner configuration" from the service menu
and enter the numbers 2, 3, 5, 6 in sequence. Examine Cloner Configuration
section in Service menu for detailed information.

14.5. TeraTerm Setup

1. Run teraterm. Exe file to setup teraterm to your PC.

2. Make the serial port setting as seen below picture, select setup and “serial
port”
3.

September 2012 118

 J5 CHASSIS / TELEVISION

Select your serial port and make the other settings as seen below

Recording Log File

Select “File” and then “log” selection as seen below

Then give a name to file and save it as seen below

September 2012 119

 J5 CHASSIS / TELEVISION

When the record ends select “close” selection as seen below

14.6 Software and Key Map

Software / KEy memory

Main software
Chassis serail number NAND Flash
Product serial number
Boot code
CI+ SPI Flash
Acoustic
Mac address
Panel
HDCP Key
Panel Eeprom
SSL - Secure Socket Layer

Gamma

HDMI EDID HDMI Eeprom

September 2012 120

 J5 CHASSIS / TELEVISION

15. SUPPORTED RESOLUTIONS

15.1.PC-DVI Resolution Info

Resolutions that can be used with computer connection:

15.2. HDMI-H PC Resolution Info

September 2012 121

 J5 CHASSIS / TELEVISION

15.3. HDMI-H YPbPr Resolution Info

Resolutions
480i 60Hz
480p 60Hz
576i 50Hz
576p 50Hz
720p 50Hz
720p 60Hz
1080i 50Hz
1080i 60Hz
1080p 24fps
1080p 25fps
1080p 30fps
1080p 50Hz
1080p 60Hz

September 2012 122

 J5 CHASSIS / TELEVISION

16. HOTEL TV SETUP

Hotel TV is intended to prevent hotel guests from changing TV’s channel settings and turning
volume up to disturbing levels for the environment. Therefore, “Source Settings” tab is not
shown in user menu.

Check whether the “Hotel TV” option under the System Configuration tab in Service Menu is
“On” to perform the desired settings in HOTEL TV. If the “Hotel TV” tab is ON in the service
menu, then we must open the “Hotel TV Settings” menu and log in as “Admin” to perform any
operation in this menu.

Video Settings

Open the user menu by pressing “Menu” button in order to open the Hotel TV Settings menu
and make operations in this menu. On the Video Settings, use password 4, 6, 5, 8 to turn off
and on the MENU once; thus you can access HOTEL TV settings and get the authorization
(admin mode) to perform settings in HOTEL TV mode. Remember that Hotel TV settings
shall not be displayed when the TV is turned off and on again. Above-stated procedures
have to be repeated if any change is to be made on the settings again.

On the HOTEL TV SETTINGS menu, we can perform channel tuning (Source Setup menu),
maximum initial sound volume settings and whether TV will stay on Stand-By or directly
switch on when plugged in (Hotel TV Settings menu). This feature turns off after TV is
switched to Stand-By.

September 2012 123

 J5 CHASSIS / TELEVISION

The channels are tuned and favourite list is determined over source settings. In customer
mode, TV is turned on at the channel and source where it was turned off at admin mode.
This feature should be used to set TV’s opening channel. As an opening channel, you may
set the hotel's own advertisement channel with hotel's videos or a channel advertising paid
broadcasts. In customer mode, it is not an error that TV is turned on at the same source and
channel whichever channel or source was open when turning off the TV. You should
consider this issue before switching TV to Stand-By in Admin mode.

When setting up hotel TV, the easiest and most convenient way is to perform all settings on
a single TV and copy the same configuration to other TVs by means of cloning feature. Here,
you should make sure that TV is turned off at the intended channel after completing setup at
the admin mode.

“Cloner Configuration” menu has to be opened in order to use the cloning feature from the
USB. Cloner Configuration menu can be turned on by two ways. First one is to navigate to
the “Cloner configuration” tab and press 4, 6, 5, 8 keys. Another option is to press 4,6,5,8 to
enter Cloning menu in the Source Setting/Program Table while you are in Hotel TV admin
mode.

In the Cloning menu:

Copy selects what and to where we want to copy. TV to USB copies the configuration on TV
to the USB. USB to TV transfers previously prepared channel list, user and satellite settings
to TV.

Copy item is the name of configuration to be copied. Channel/Video Set selection enables
transferring channels, frequencies and favourite lists that were already set. Service Set
enables transferring service menu settings. When installing at the user’s place, this option
should NOT BE CLONED. User Set enables us to transfer user settings (sound, brightness,
TV language and etc.).
Start Cloning option starts the cloning process. Whereas TV to USB takes little time, USB to
TV causes a short interruption of TV imaging. When TV automatically restarts after
installation, its means cloning is completed.

September 2012 124

 J5 CHASSIS / TELEVISION

17. J5 CHASSIS DIGITURK ENABLED TV SETUP

Our J5-chassis digital broadcasting enabled televisions are launched together with Digiturk
membership package according to the agreement entered with Digiturk. In our TVs, Digiturk
mode will run over Eutelsat 7.0° satellite.

In addition to standard accessories of a TV, these products also come with the accessories
that enable reception of Digiturk satellite broadcasting.

1. CA module (CAM) (JLS120R DIGITURK IRDETO CI+ CA MODULE)

2. Smart Card (JLS180R DIGITURK IRDETO CI+ CA CARD)
3. Digiturk Password Envelope (JLS813 DIGITURK PASSWORD ENVELOPE)
4. Digiturk Agreement (JLK813 DIGITURK AGREEMENT)

NOTE: The module and card that comes with the product are the property of the customer,
they cannot be reclaimed after Digiturk membership expires.

17.1.Television setup

Once TV’s mains and (satellite) antenna connection is completed, Installation Guide appears
on the screen when the TV is turned on for the first time. In the first screen, "Turkish" is
selected for language. And after selecting "Home Mode" in the second screen and "Turkey"
in the third screen, you should select “satellite” for “Connection Type” via joystick in the fourth
screen.
As this is Digiturk setup, “Digiturk Mode” is selected in the 5th screen.
If diseq switch (it is required in the systems with more than one satellite) is not used in the
system and Eutelsat 7° satellite (standard Digiturk dish direction) oriented dish antenna is
connected, “easy installation” will be selected in 6th screen to continue. 7. When “Start”
(green line) is pressed on the display, the channels will be automatically searched and listed.
If diseq switch is used in the system, "Advanced Installation" will be selected to enter
“Antenna Settings” and Diseq selection related to Eutelsat will be determined.
Note: MDU selection is not required, MDUs are automatically scanned.

When the setup of channels is completed, the card will be installed in CA module and
the module will be inserted into the related module input of TV.

Once the module is inserted, module verification process starts. In this case, warning menus
appear on TV.
On “CA – Module” menu, we should see “Irdeto Access” message.

September 2012 125

 J5 CHASSIS / TELEVISION

After selecting CA – Module => Irdeto CA Status => Digital Card Status, we should see serial
number of the Smart card as well as "Card Inserted" message in "Status" tab. If the card is
inserted incorrectly or if it is broken, the information on this menu may be missing.

After this check, please select CA Module=>CAM Management=>CAM Info and check CAM
software and hardware. Any missing or irrelevant information indicates that CAM module is
faulty.

Continue with the setup after these checks.

Later, you should call Digiturk to activate the membership. Please have the password
envelope with you for this call.
After setup is completed, “Digiturk Agreement” that comes with the product will be filled in. In
this agreement, serial number of CI+ module will be entered in the Digiturk serial no section
and serial number of smart card will be entered in the Digikart serial no section.
Besides, after setup; video and audio should be checked especially in HD (TRT HD, SHOW
HD) and SD channels. In case of broadcasting problems, you should determine if the
problem rests in Digiturk broadcasting or the current installation.
If there is any problem on the installation, broadcasting quality or level, in case of a problem
in signal level (caused by the use of long cable), In-line amplifier may be attached;

September 2012 126

 J5 CHASSIS / TELEVISION

on headend systems where analog and digital broadcasts (VHF, UHF, IF) are provided
through the same cable, diplexer may be attached to the system as a filter.
If the user has only Turksat 42°-directed dish, it should be set to Eutelsat 7° .
Note: If the customers have inquiries about membership package, broadcasting and etc, they
should be recommended to contact Digiturk.
Against the complaints about Digiturk-enabled TVs’ decoding:

Before reporting error in such issues, please ensure that “Irdeto Access” message appears in
“CA – Module” menu.

September 2012 127

 J5 CHASSIS / TELEVISION

After selecting CA – Module => Irdeto CA Status => Digital Card Status, we should see serial
number of the Smart card as well as "Card Inserted" message in "Status" tab. If the card is
inserted incorrectly or if it is broken, the information on this menu may be missing.
After this check, please select CA Module=>CAM Management=>CAM Info and check CAM
software and hardware. Any missing or irrelevant information indicates that CAM module is
faulty.

September 2012 128

 J5 CHASSIS / TELEVISION

If the problem is not solved after these checks, make sure the problem does not rest in the
broadcast.
Call Digiturk customer services to check CAM number (starting with OAF) and card number
and have them verified.
Ask Digiturk customer services to reset all signals coming to this module.

September 2012 129

 J5 CHASSIS / TELEVISION

18. FINDING MISSING CHANNELS ON PRODUCTS WITH SATELLITE RECEIVER

On satellite source, when automatic channel search is performed in Turksat, missing channel
problem may be encountered.
When automatic search is performed on satellite source, channel search is done according
to the frequencies in the transponder list installed on television software and the discovered
channels are stored. (When satellite source is selected in Source Settings menu, press right
arrow on the transponder option to view the list of stored transponders.)
The problem results from that this transponder lists change in time or new ones are added. In
J5-chassis products, even though new transponder lists are added in updated software, this
list may lose validity in time. If manual search is performed with the information about newly
added or changing frequencies, the channels will be found out and added to the end of the
list.

As a solution; Turksat satellite has a “Turksat Auto Search and Teletext” channel, (namely
TURKSAT PROMO). This channel make V (vertical) broadcasting on 11844Mhz frequency
and with 02222 symbol rate. With digital manual tuning option, enter this frequency and
perform tuning by selecting “Network Search” option “On” in order to scan and find current
satellite channels by “Türksat Uydu Haberleşme Kablo TV ve İşletme A.Ş”.

Note: Also, Turksat promo channels are available on 12729 and 12015 frequencies, but
current network search frequency is 11844Mhz.
Turksat channel list's broadcasting information and automatic channel tuning frequency may
change in time. Updated information may be obtained on Turksat’s website.

http://uydu.turksat.com.tr/UyduFrekans/index.php
http://www.turksat.com.tr/

September 2012 130