ENGLISH

CONTENTS

1) Foreword page 2
2) Dimensions 2
3) General description 3
4) Packaging 3
5) Disposal 3
6) Use 4
7) Installation and wiring 4
8) Operation of the appliance 5

9) Warnings regarding operation 8

10) Safety devices 9

11) Warnings regarding safety 10

12) Noise levels 10

13) Maintenance 11

14) Cleaning the appliance 11

1
1) FOREWORD
Read this manual from cover to cover before using the appliance as it contains important
instructions for the safety, operation and maintenance of the appliance.
Look after this manual and keep it in a safe place.
The manufacturer reserves the right to make changes to the product and to the manual.

2) DIMENSIONS

GRINDER-DOSER GRINDER-DOSER GRINDER-DOSER

MINI LUX SUPER JOLLY

* alternative height
with optional hopper

ELECTRONIC ELECTRONIC ELECTRONIC

GRINDER-DOSER GRINDER-DOSER GRINDER-DOSER
MINI mod. A MINI mod. B SUPER JOLLY

* alternative height * alternative height

with optional hopper with optional hopper

COFFEE GRINDER
SUPER JOLLY

2
 ENGLISH

3) GENERAL DESCRIPTION
HOPPER COVER

HOPPER
(coffee bean container)

COFFEE GRINDING
ADJUSTMENT DISK LOCKING SLIDE

PUSH BUTTON PANEL

FUNNEL

GRINDING
ADJUSTMENT DISK HANDLE SERIAL NUMBER LABEL

DOSER COVER

DOSER

COUNTER

COFFEE PRESSING DEVICE

DOSING LEVEL

FILTER HOLDER FORK

SWITCH

DRIP TRAY

4) PACKAGING
On opening the packaging, check carefully to make sure the appliance is intact and that there
are no signs of damage. If in any doubt, do not use the unit and contact personnel with the
appropriate professional skills.
The packaging materials must be kept out of the reach of children as they represent a potential
source of danger.
Keep the packaging until the warranty has expired.

5) DISPOSAL
Do not litter: dispose of the packaging materials according to the laws in force.
Should you decide not to use the appliance any more, remember to unplug it so that it cannot
be used, and then cut the cable in the point where it comes out of the appliance.
Contact specialized firms for information on the disposal of the components of the appliance.
INFORMATION FOR USERS RESIDING IN THE EUROPEAN UNION
In accordance with art. 13 of Legislative Decree of 25 July 2005, no. 151: “Implementation of Directives 2002/95/EC
and 2002/96/EC, concerning the reduction in use of hazardous substances in electronic and electrical equipment and
disposal of waste”.
The symbol shown here, which is also shown on the equipment, means that the equipment along with all the
components and sub-assemblies which are an integral part of the product, must be collected separately when
the user no longer needs it.
For more information, visit www.mazzer.com.

3
6) USE
This appliance has been designed SOLELY for grinding coffee beans. Any other use is
understood to be improper, and consequently hazardous. The manufacturer cannot be held
responsible for any damage as a result of improper or incorrect use.
Do not use the appliance for grinding other types of food, or anything else.
Do not use the doser (Grinder-Doser version) to store foods or measure them.
THE GRINDER-DOSERS, ELECTRONIC GRINDER-DOSERS AND COFFEE GRINDERS
MANUFACTURED BY OUR COMPANY ARE INTENDED FOR SKILLED PERSONNEL
ONLY FOR PROFESSIONAL USE AND NOT FOR HOUSEHOLD USE. USE The user must be an
adult.
Do not allow children or incapable persons to use the appliance.

7) INSTALLATION AND WIRING

The appliance must be installed by skilled technical personnel in conformity with the safety
rules in force. Incorrect installation may result in injury of persons or animals, or damage to
property, for which the manufacturer cannot be held responsible.
• The appliance must be placed on a stable, flat surface (we recommend to install the
appliance at an height between 80 and 100 cm from the floor).
• Before plugging in the appliance, make sure the voltage and frequency values of the supply
mains correspond to the ratings indicated on the label featuring the appliance’s technical data.
• The wall socket must be fitted with an efficient earth contact. Consequently, it is essential to
make sure the earth system is efficient and in conformity with current safety rules. If in any
doubt, have the system thoroughly checked by personnel with the appropriate professional
skills.
IT IS COMPULSORY TO EARTH THE APPLIANCE.
The manufacturer cannot be held responsible in the event this regulation is not complied with.
• It is essential to make sure the ratings of the system are suitable for the power absorbed by
the appliance - as indicated on the label featuring the technical data - and that the wall socket
is protected against overcurrents.
• Do not use extension cables, plug adapters for multiple sockets or makeshift connections.
• In EEC member countries, the regulation in force calls for the external equipotential terminal
on the outer part of the appliance’s base plate to be connected to a equipotential node if
the installation is to be correct.
• The motor must rotate clockwise. If the rotation of three-phase motors is to be inverted, by
inverting the two power supply wires inside the plug, this must be carried out by skilled
personnel.
• THE HOPPER MUST BE FASTENED TO THE APPLIANCE’S GRINDING SYSTEM BY
MEANS OF THE RELEVANT SCREW which must be inserted in the threaded hole located
on the upper grinding blade holder and in the hole on the neck of the hopper.
• The appliance is suitable for indoor use only. Do not use the appliance outdoor.
• Thoroughly clean the appliance at the first installation; follow the instructions in chapter 9 and
14.
• Do not install the appliance near to water dispenser or similar product that could throw water
jet on the appliance.

4
 ENGLISH

8) OPERATION OF THE APPLIANCE

PRELIMINARIES
Make sure the hopper is positioned correctly on the HOPPER
appliance and is fastened to the upper grinding blade
holder by means of the relevant screw.
Close the locking slide and fill the hopper with coffee HOPPER
SAFETY SCREW OPEN
beans. Open the locking slide so that the beans are
allowed to drop into the grinding system.

SWITCHING THE APPLIANCE ON AND OFF

Grinder-Dosers with manual switch and Coffee Grinders
The on-off switch is used to turn the appliance both on and off.
To switch on: set the switch to I.
To switch off: set the switch to O.
Grinder-Dosers with time switch
In order to switch the appliance on, turn the timer knob clockwise.
The appliance switches off automatically. In order to switch it off manually, turn the knob
anticlockwise all the way.
Automatic Grinder-Dosers
In order to power up the appliance, turn the on-off switch knob to I. In order to switch the
appliance on manually, the switch knob must be turned all the way (to START).
The appliance starts automatically every 12 portions of coffee (every 6 portions in the model
MINI/LUX and in the versions with shorter doser group). It switches off automatically when the
doser is filled with ground coffee.
In order to switch off the appliance manually, set the on-off switch knob to O.
Electronic Grinder-Dosers
In order to power up the appliance, set the on-off knob to I. DISPLAY
The display located on the lid of the push button panel will
MENU BUTTON
show a counter with the incremental number of doses PUSH BUTTON FOR
ground by the appliance. MANUAL GRINDING

After having placed the filter holder on the filter holder fork SINGLE DOSE BUTTON
push: DOUBLE DOSE BUTTON
- the push button on the left (indicating one cup) to grind
and dispense a single dose;
- the push button on the right (indicating two cups) to grind and dispense a double dose.
The counter adds one for each single dose (one cup sign) and adds two for each double dose
(two cup sign).
One can manually activate the appliance keeping pushed the push button for manual grinding
(indicating ) located in the centre of push-panel. Hold down the push button for manual
grinding and the grinder will grind until you lift the finger. By using the push button for manual
grinding no dose is added in the counter.
We suggest to use the push button for manual grinding to adjust the grinding of the appliance.
In order to switch off the appliance turn the knob of the switch to O.

5
Mini mod. B Electronic Grinder-Doser
In order to power up the appliance, set the on-off knob to I.
After having placed the filterholder on the filterholder fork,
push the central button as follow: DOSING PUSH BUTTON
- push one time to dose a single dose (the light indicating
one cup turns on);
- push two time (with a waiting range of 1 sec between two
pushing) to dose a double dose (the light indicating two
cups turns on).
One can manually activate the appliance keeping pushed in the central button (both the lights
are winking simultaneously), letting go the central switch will stop the grinding. This central
switch is meant to facilitate the adjustment of the coarseness of the grind of the appliance.
In order to switch off the appliance manually, set the on-off switch knob to O.

ADJUSTING GRINDING
In order to achieve finer or coarser grinding, the adjust-
ment disk located under the hopper must be adjusted
using the relevant handle. In order to increase the coarse- FINER
GRINDING
ness of the ground coffee, the disk must be rotated clock-
wise; to decrease, turn the disk anticlockwise. COARSER

The disk remains in the chosen position without having to GRINDING

be locked in place. The adjustment must be performed

with the motor on, and preferably without any coffee between the grinding blades. Grind small
amounts of coffee in order to determine the optimal degree of fineness.
In the Electronic Grinder-Doser version, before checking the fineness of the ground coffee,
grind some doses of coffee to fill the duct between the grinding area and the outlet. This
operation must be done whenever the grinding setting has been changed in order to empty the
duct of the previous ground coffee. The change of the grinding setting might vary the weight of
the doses. Therefore adjust the doses only after the grinding setting.
In the Grinder-Doser and Electronic Grinder-Doser versions, if the coffee comes out of the
espresso coffee machine very quickly, it means the coffee is ground too coarse. Vice versa, if it
comes out too slowly, it means the coffee is ground too fine. Nonetheless, bear in mind that
there are many conditions liable to influence the correct supply, such as the weight of the
portions, the compacting, the espresso machine settings, and the cleaning of the filters.

COFFEE DOSE ADJUSTMENT

Grinder-Dosers
In order to adjust the size of the portion dispensed, the small knob located in the centre of the
ground coffee storage container must be turned while holding still the star shaped dosing unit.
By turning the small knob clockwise, the portion is reduced. Turning it anticlockwise results in
an increase.
In order to collect the portions of ground coffee dispensed, insert the coffee machine’s filter
holder all the way onto the fork-shaped support under the ground coffee outlet. In order to
release a portion of ground coffee, the doser lever must be pulled all the way and allowed to
return on its own. Pull twice in a row for a double portion.
In manual coffee Grinder-Dosers and those with time switches, in order to assure the portions
are regular, check every now and again to make sure the amount of coffee ground to be found
in the doser is sufficient to cover the feeding star unit.

6
 ENGLISH

COFFEE DOSE ADJUSTMENT COLLECTING

THE DOSE

REDUCE
THE DOSE

INCREASE
THE DOSE

To centre the coffee drop into the filter holder, it is possible to carry out a sideways adjustment
of the support fork located under the dispenser, by slightly loosening the fixing screws and then
tightening them again after having moved the fork into the new position.
Electronic Grinder-Dosers
In order to adjust the size of the portion dispensed, use the push button controls located on the
lid of the funnel. After having set the optimal degree of fineness, check the weight of the dose
with a digital precision scale.
In order to adjust the dose press the push button “MENU” for 3 seconds; the display will blink.
Select the dose you wish to adjust : either the single dose (indicating one cup) or the double
dose (indicating two cups). The display will show the grinding time (in seconds) of the selected
dose. By pressing the push buttons “+” and “-“ the grinding time can be increased or decreased
and consequently the selected dose can be increased or decreased.
Approximately, a change of 0.10 seconds is equivalent to a change of dose of 0.15 grams
(0.005 ounces).
To set the desired amount of grinding time press the push button “MENU” for 3 seconds. A
blinking of the display will confirm the data have been saved and the exit from the adjusting
program.
Use a digital precision scale to check again the weight of the dose and, if necessary, repeat
above mentioned operation.
PUSH BUTTON PANEL

GRINDING TIME
MENU BUTTON ADJUSTMENT BUTTON

PUSH BUTTON FOR

DISPLAY MANUAL GRINDING

SINGLE DOSE BUTTON DOUBLE DOSE BUTTON

WHEN YOU ARE INSIDE THE ADJUSTING PROGRAM IT IS NOT POSSIBLE TO

OPERATE THE APPLIANCE.
IF THE APPLIANCE GETS SWITCHED OFF (SWITCH IN THE POSITION O) BEFORE
EXITING FROM THE ADJUSTING PROGRAM THE CHANGES ARE NOT SAVED.
In order to collect the portions of ground coffee, insert the filter holder all the way onto the fork-
shaped support under the ground coffee outlet.

7
Mini mod. B Electronic Grinder-Doser
In order to adjust the size of the portion dispensed, one has to regulate the trimmer setting,
positioned above the filterholder.
The trimmer on the left regulates the single dose (one cup).
The trimmer on the right regulates the double dose (two cup).
SINGLE DOSE
ADJUSTMENT TRIMMER

DOUBLE DOSE
ADJUSTMENT TRIMMER

By turning the trimmer setting clockwise, the portion is increased. Turning it anticlockwise
results in an reduction of the portion.
A rotation of 180° (half a turn) of the trimmer results in a variation of about one gram of ground
coffee dispensed.
In order to collect the portions of ground coffee dispensed, insert the coffee machine’s filter
holder all the way onto the fork-shaped support under the ground coffee outlet.

PRESSING (Grinder-Dosers)
STATIC PRESSING DEVICE: place the filter holder against the underside of the pressing
device and push upwards.
SPRING PRESSING DEVICE: place the compacting disk against the upper face of the filter
holder inserted in the fork-shaped support and press down on the spring pressing device knob.
STATIC SPRING
PRESSING DEVICE PRESSING DEVICE

9) WARNINGS REGARDING OPERATION

• Do not leave the appliances turned ON without coffee in the hopper.
• In the Grinder-Doser version, avoid pulling the dosing lever partially, always pull it all the way.
• In the Coffee Grinder version it is essential that nothing
hinders the flow of ground coffee from the outlet in any way
in order to prevent the risk of the appliance stopping.
Consequently, avoid using coffee bags which are too small COFFEE
OUTLET SPOUT
with respect to the amount of coffee to be ground. At the end
of each grinding-cycle, shake the handle of the spout for a
complete outlet of the coffee.
• Do not insert, when filling the hopper with coffee beans, foreign objects. Handle with clean
hands.
• After any hopper filling and in normal use of the appliance, the hopper lid must be positioned
correctly.

8
 ENGLISH

• FIRST INSTALLATION
For the correct use of the grinding blades, at the first installation or whenever the grinding
blades have been replaced, grind some doses of coffee. Do not use those first doses.
In the Electronic Grinder-Doser version, for the appliance to function at its best, on its first
installation and every time the hopper is cleaned, after having ground a few coffee doses,
clean the inner surface of the funnel with a dry brush.
• OPERATING RANGE OF THE MOTOR
IN THE VERSIONS WITH SINGLE-PHASE MOTORS, OBSERVE THE DUTY CYCLE
STATED IN THE LABEL LOCATED ON THE SIDE OF THE APPLIANCE.
E. g. : a data on the label 35s ON / 45s OFF points out an allowed duty cycle of 35 seconds
switched on and 45 seconds switched off.
APPLIANCES WITH THREE-PHASE MOTORS ARE ALLOWED FOR CONTINUOUS
WORKING.
In order to achieve good grinding, it is nonetheless recommended to operate the appliance at
intervals, allowing it to operate for no more than 10-15 minutes at a time.

10) SAFETY DEVICES

THERMAL OVERLOAD PROTECTION
The appliance’s motor is protected against overheating resulting from overcurrents by a thermal
overload protection which, when tripped, cuts off the power supply to the motor. Should the
protection trip as a result of anomalous operation, such as the grinding blades jamming, the
appliance must be turned off using the on-off switch, UNPLUGGED FROM THE MAINS, AND
SKILLED TECHNICAL PERSONNEL CONTACTED. NEVER PERFORM ANY WORK ON
THE APPLIANCE WHILE IT IS ATTACHED TO THE MAINS, TO AVOID THE RISK THAT
MOTOR TURNS ON SUDDENLY. If the appliance overheats as a result of the motor stopping,
allow the appliance to cool down before performing any repair work.
SAFETY SCREWS
The hopper must always be attached to the upper grinding
DISK SAFETY SCREW
blade holder using the relevant screw, which must not be ALTERNATIVE
removed by the user under any circumstances. THREADED HOLE

In order to prevent the adjustment disk from being removed - HOPPER SAFETY SCREW
which would make the rotating parts accessible - there is a
safety screw on the actual disk: said screw must be positioned COFFEE OUTLET GUARD
in whichever of the two holes on the disk enables the wider
and most suitable range of grinding adjustment, and must not be removed by the user under
any circumstances.
COFFEE OUTLET GUARD
The coffee outlet guard must always be fixed to the doser (Grinder-Dosers), or to the funnel
(Electronic Grinder-Dosers), using the relevant screws, which must never be removed by the
user. THE REMOVAL OF THE COFFEE OUTLET GUARD CAN BE DONE BY SKILLED
TECHNICAL PERSONNEL ONLY AFTER DISCONNECTING THE APPLIANCE FROM THE
POWER SUPPLY BY UNPLUGGING.
Before reconnecting the appliance to the power supply, fix the safety device to the doser, or to
the funnel, by relevant screws.

9
11) WARNINGS REGARDING SAFETY
This electrical appliance must be used in conformity with the rules in force governing safe
operation.
• WHEN OPERATING THE APPLIANCE, BEWARE OF THE MOVING MECHANICAL
PARTS’ IN THE AREA OF THE GRINDING BLADES AND OF THE GROUND COFFEE
OUTLET. BEFORE REMOVING THE HOPPER FROM THE GRINDING SYSTEM,
DISCONNECT THE POWER SUPPLY. AVOID REMOVING FOREIGN BODIES FROM
THE GRINDING SYSTEM OR HOPPER WITHOUT FIRST UNPLUGGING THE
APPLIANCE FROM THE MAINS.
• Take care, as the grinding blades may continue rotating for a short while even after the
appliance is switched off.
• THE USER IS NOT AUTHORIZED TO REMOVE SCREWS OR ANY PARTS SCREWED
ONTO THE APPLIANCE.
• In the event the appliance is not working properly or is faulty, contact skilled technical
personnel, and do not attempt to make repairs yourself.
• BEFORE PERFORMING ANY WORK ON THE APPLIANCE, INCLUDING CLEANING
AND/OR MAINTENANCE, DISCONNECT IT FROM THE POWER SUPPLY BY
UNPLUGGING. TURNING OFF THE APPLIANCE USING ITS MASTER SWITCH DOES
NOT ASSURE THE SAME CONDITIONS OF SAFETY.
• Do not tamper with the appliance.
• When the appliance is left unattended, the appliance’s power supply must be disconnected
using its master switch (for example, at night, during work breaks, midweek closing or
holidays).
• Do not let liquids of any kind come into contact with the internal or external parts of the
appliance.
• Never put ground coffee in the hopper intended only for coffee beans.
• DO NOT TUG ON THE SUPPLY CABLE TO UNPLUG THE APPLIANCE FROM THE
MAINS.
• Do not touch the appliance with damp or wet hands or feet.
• Do not use the appliance barefoot.
The manufacturer cannot be held responsible for bodily injury or damage to property if these
regulations are not complied with.

12) NOISE LEVEL

EEC Countries:
The maximal noise emission of our appliances (valued as acoustic power) is 81 dB(A).
The daily personal noise exposure of a worker, due ONLY to an appliance’s limit operation of
240 minutes per eight hours, is 78 dB(A), according to European Directive 86/188/EEC and
European Directive 2003/10/EC. Therefore during he appliance’s normal operation, no
provisions are to be taken in order to prevent such risks arising or likely to arise from noise
exposure at work (articles 3-8 of European Directive 2003/10/EC).
USA & Canada:
The noise level of our appliances is included within the limits stated in U. S. regulation 29 CFR
1910. 95 (‘Occupational Health and Environment Control - Occupational noise exposure’) for
eight hours continuously in a day (in reference to a noise exposure due solely to appliance
operation).
Said noise level has been determined on identical news appliances.

10
 ENGLISH

13) MAINTENANCE
It is essential to check the state of the supply cable and plug periodically.
IN THE EVENT THE SUPPLY CABLE OR PLUG ARE DAMAGED, CALL IN SKILLED
TECHNICAL PERSONNEL TO REPLACE THEM, THIS TO PREVENT ANY RISK.
IN -CERTIFIED APPLIANCES, A SPECIAL TOOL IS REQUIRED TO OPEN THE BASE
PLATE TO GET AT THE CABLE.
It is recommended to use original spare parts only.
In order to assure the lasting efficiency of the appliance, skilled technical personnel must be
called in to perform periodical maintenance, including detailed checks of the state of those
components subject to wear.
The state of the grinding blades must be checked periodically. Keeping the grinding blades in
an excellent state assures high-quality grinding, resulting in greater productivity and limited
overheating.

14) CLEANING THE APPLIANCE

DISCONNECT THE APPLIANCE’S POWER SUPPLY BY UNPLUGGING IT BEFORE
CLEANING. THE APPLIANCE MUST NOT BE CLEANED USING WATER JETS.
Do not install the appliance in rooms where water jets are used for cleaning.
THE APPLIANCE MUST BE CLEANED PERIODICALLY BY SKILLED TECHNICAL
PERSONNEL ONLY.
Use perfectly clean, disinfected cloths or brushes for cleaning.
Do not use abrasive products as these are liable to take the sheen off shiny parts.
Hopper
Wash the hopper once it has been removed from the appliance (unscrewing the relevant
fastening screw), using neutral soap and water, rinse abundantly with lukewarm water and dry
thoroughly. It is advisable to clean the hopper periodically. Once the hopper has been cleaned,
it must be attached to the upper grinding blade holder using the relevant screw.
Grinding system
Remove the safety screw which prevents the adjustment GRINDING
disk from being removed. Unscrew the adjustment disk by ADJUSTMENT DISK
UPPER GRINDING
turning it clockwise. Having removed the upper grinding BLADE HOLDER
blade holder, clean the grinding blades, threads and the GRINDING
ADJUSTMENT SPRINGS
entire grinding system thoroughly using a clean brush and
cloth. To clean the threads of the grinder please use a
small wire brush.
We recommend to check that the threads of the grinder and of the grinding adjustment disk are
clean: to do so screw the adjustment disk anti-clockwise
without the upper blade holder until the end. If the grinding adjustment disk can not turn easily,
than it is necessary to clean again. If the cleaning operations are not done as above the risk is
to damage the threads.
Please check that the grinding adjustment springs are on their place. Having refitted the upper
grinding blade holder in the relevant slot, please lubricate, with grease suitable for food contact,
the threads of the grinding adjustment disk and its underneath surface which touches the
upper grinding blade holder.
Screw the adjustment disk by turning it anticlockwise, put the self-locking screw back in
whichever of the two holes on the disk enables the best adjustment and, having refitted the
hopper and secured, adjust the grinding as required.

11
Doser (Grinder-Dosers)
Having discharged the ground coffee, clean the doser’s star unit with a clean brush, expelling
the material removed by pulling the doser lever.
Use a dry cloth to thoroughly clean the outlet of the ground coffee on the bottom of the doser.
When a more thorough cleaning is required, the operation must be performed only by skilled
technical personnel, after disconnecting the appliance from the power supply,
supply according to the
following instructions:
1. Remove the coffee outlet guard unscrewing the relevant screws;
2. Unscrew the hexagonal-head screw that fix the coffee dose adjustment knob;
3. Unscrew (anticlockwise) the coffee dose adjustment knob holding the doser’s stars unit
(female dosing star and the upper dosing star) pushed down;
4. Remove the doser’s stars unit;
5. Remove the central spring;
6. Clean thoroughly the bottom of the doser, especially the sharp edges on sight and the outlet
of the ground coffee.
In order to reassemble the doser, follow the previous instructions in inverted order; pay
attention that the feather of the coffee-outlet covering section plate is correctly set in the proper
slide on the side of the basin.
Spout (Coffee Grinders with bag holder)
Wipe clean the spout from which ground coffee is released using a dry cloth.
Funnel (Electronic Grinder-Dosers)
After having removed the lid, clean the funnel and its lid with a dry and disinfected brush.

Mazzer Luigi srl

All right reserved. It is prohibited to reproduce, adapt or translate this document without prior
written authorization.

First Edition: 2001

Last Revised: SJ09 09/2012

12