Scribd
Upload
9 views2 pages

RC I Course Out Line (Civil 4th Yr 2024)'

Uploaded by

Кибром Фисеха
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
9 views2 pages

RC I Course Out Line (Civil 4th Yr 2024)'

Uploaded by

Кибром Фисеха
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Addis Ababa Science & Technology University

College of Engineering
Department of Civil Engineering
Reinforced Concrete Structures I (RC I) – Course Out Line

Course Number: CEng4107 Year: 4


Pre-requisite: CEng 3106 Theory of Structure - II Semester: I
Instructor: Yohannes K. & Bayelign H. Credit Points: 3
Contact Address: [email protected] (B-63, Room-408) ECTS Credits: 5
Contact Address: [email protected] (B-63, Room-006)
Course objectives & competences to be acquired:
At the end of this course, students should be able to:
• Understand the general behavior of concrete and steel under different type of loading
• Analyze and design singly and doubly reinforced concrete beams under flexure,
including regular (rectangular shaped), T-Beams and L-beams.
• Analyze and design structural reinforced concrete beams subjected to shear loading
• Determine bond length, lap splice and detailing requirements for RC beam members
• Analyze and design One Way Ribbed, One way Solid and Two way Solid slabs
• Conduct a service load analysis to control deflection and cracking of beams.
• Apply structural analysis software and excel package to solve reinforced concrete
Design problems CHAPTER 2: Limit State Design of
Beams for Flexure
2.1 I General data on concrete and
steel
2.2 Design preliminaries
2.3 Singly reinforced beams
CHAPTER 1: Introduction
2.4 Doubly reinforced beams
1.1 General Review
1.2 Behavior of plain 2.5 T and L beam
concrete/reinforced concrete 2.6 SAP2000 or ETABS and Excel
members under loads application
1.3 Behavior of steel under
tension
1.4 Design philosophies
CHAPTER 3: Limit state design of beams for Shear/diagonal tension/, bond
and anchorage
3.1 Introduction
3.2 Design of Sections for Shear
3.3 Bond and Development Length
3.4 SAP2000 or ETABS and Excel application for shear design of beams
CHAPTER 4: Design 4.5 Software application for design of
slabs
of Solid and
Ribbed Slabs CHAPTER 5: Serviceability Limit
4.1 Introduction
State
4.2 Design of One way Ribbed 5.1 Cracking in Flexural Members
Slab 5.2 EBCS Provision for Crack Control
4.3 Design of One Way Solid 5.3 Deflection of Elastic Sections
Slab 5.4 Creep and Shrinkage Deflections
4.4 Design of Two way Solid 5.5 EBCS Provision for Deflection
Slabs Control
Note: All Projects and Assignments Must be submitted 3 days after completion of
the corresponding chapter or topic)

Assessment/Evaluation & Grading System

References:
1. Arthur H Nelson, Design of concrete structures, McGraw-Hill, 14th Edition, 2010
2. James Macgregor Reinforced Concrete Mechanics and Design, 5th Edition.
3. W.H. Mosley, R. Hulse, J.H Bungey, Reinforced Concrete Design, Palgrave Macmillan, 2007
4. Jack C. McCormac, Design of Reinforced Concrete, McGraw-Hill, 2005
5. Ethiopian Standards based on Euro Norms ES EN 1992:2015
6. Ethiopian Building Code Standard 2 (EBCS 2), 1995 ….& any other Related Books

You might also like