A

C
SE
N
FO
I hope this will help
And also the ecu eeprom and immo box eeprom is included
They are original (virgin)
Ecu-MC9S12KG256.bin
Inmobox-95040.bin
Ecu MT20UED (with mcu 9S12KG256) Mask 2L33V
- Immo box (with eeprom 95040)
I read with X-prog, make sure read verify is NOT ticked, u will probably erase the chip

Symptom:
This car in a normal course of the exercise of a sudden flameout, how can launch after
the engine flameout vain, theft indicator flashes quickly.
Diagnostic process:
this car is low, although the vehicle, but the vehicle anti-theft system matching was more
advanced, when the anti-theft system lockup, no corresponding devices are difficult to
unravel. Happens to this car anti-theft system designed to have flaws, when the ignition
system when there is strong interference will disrupt their normal operating procedures,
resulting in anti-theft system somehow locked, so the car's anti-theft can also be said in
this A common problem car. There are a lot of maintenance personnel in the solution of
the anti-theft system, he often is a system-wide change, including the engine computer,
security box and key, so although able to troubleshoot, but gave owners to bring
additional financial burden. After our long-term exploration and in the absence of
original equipment support, obtained without replacing any parts you can unlock the car
anti-theft lock method for the owners to save a lot of expenses.

We rushed to the scene after receiving calls for help, ruled out the problems
facing the circuit diagram line aspects of diagnostic detection alarm box with a lot of
storage and clear fault codes cannot afford, determine the problem lies in the theft case
or the engine control unit. This car anti-theft circuit diagram as follows:
 A
C
SE
N
FO
Since we are not a service station, could not be found in the car's anti-theft password,
and replace these parts they need security password, so I decided to put the car towed
back to the repair shop and then carefully examined.
Back to the factory after the First remove the anti-theft computer located on the right
side of the instrument panel below the engine computer and instrument, the purpose of
reading data using methods to determine where the problem is. This car engine
computer model 3600010-13 for Delphi MT20UED type, security of the data stored in
MC9S12 CPU.Anti-theft box Model 3600030-C01, JIK-001, and security code data stored
in the 95040 chip, the key chips 4D-60, anti-theft induction coil resistance of
approximately 8 ohms. Physical picture is as follows:
Engine computer Appearance:
 A
C
SE
N
FO
Security computer picture is as follows:

We first open the box to read the 95040 data theft, password-bit and 17 look coding
exists, if not there will need to dismantle the engine computer read password. We have
repeatedly verified, when this happens, the security box will change 90 percent of the
data, including the 17 chassis number and security password, and the password does not
 A
C
SE
N
FO
change the engine computer. Let's take a look at the chip data after a successful match
the car's anti-theft computer 95040. As shown below:

On the red box 71ED map data is password theft car, the green box is 17 chassis
number, password and chassis numbers are normally displayed in the data. We look at
the car just started to read the data vain, as follows:

Can clearly be seen from the chart, the data has been damaged, AAAB password
location and password read out from the engine computer CPU is not the same, and 17
chassis number is also gone. This is the cause of the engine start vain most fundamental
reason, as data theft case has been damaged, and this data is broken and indirectly affect
the engine computer CPU data, so in this case, by a single cartridge to be replaced with
new anti-theft We cannot solve the problem is successful. Let us look at available from
the engine computer password method, since the data theft case has been damaged, the
 A
C
SE
N
FO
data code display position is not necessarily the correct security password, so read the
password from the engine computer is necessary, the engine computer's CPU Model
MC9S12KG256, to avoid demolition wiring diagram is as follows:

Engine computer passwords locations are as follows:

 A
C
SE
N
FO
From the engine computer work can be carried out following a match after the
security code found. Since we dedicated 431 detector software does not currently
support anti-theft case reset, so first theft box 95040 chip to write a whole new set of
data theft case, this anti-theft case is equivalent to a brand new box of theft. In order to
facilitate understanding of the new anti-theft box data, it is now the new case data
security is provided below:
The new anti-theft box data:

Password new data is 5AA5, although 5AA5 is password-bit, but in the actual
operation will never use. After the data is written to the engine computer and computer
security are loading, turn the ignition switch, the following can start match.
Connection 431, into the security system, the first clear DTCs, then select Reset engine
ECU, prompted for a password, then the password 71ED previously read input engine,
wait for about 5S, show successful reduction, which is why in the beginning to read
engine password reasons, because this step would require anti-theft password, if not
reset, it is difficult to match the success of anti-theft system. Reset can only be re-once,
 A
C
SE
N
FO
reset the password reset after the success of no use, because the engine computer has
not recognized this password. Then, after reset engine computer has the equivalent of a
new computer did not match too, plus security box also write new data, so that the car's
anti-theft system becomes a new set of the system.
Next, select the matching set of the new system, the system prompts for a
password, then the password can be set, but for the convenience of easy to remember, or
enter previously read the engine computer password 71ED, enter 2 times, wait about 5S,
prompt programming success if it is fleeting success on the show program, it is not true,
and you need it again, this step is prompted for a password and let the engine computer
security computer while the default password, then two control units only accept this
password , then select the replacement alarm match, enter the password twice 71ED, wait
about 5S, show the programming is successful, if unsuccessful continue to repeat. After
successful selection key match, the match succeeds then select programming VIN,
prompted for a password, and then enter the lower left corner of the windshield 17
encoded, and then select the input after the successful replacement of the engine ECU
matching, enter the password twice, wait about 5S programming success.
At this time in order to know the success of this system do not, the incoming data flow
options, mainly to see whether the key fitted into security computer, followed again, the
most important one, the engine computer authentication is successful, if it is on that
success, If if it does not succeed, it will have to re-match.
After the above programming operation, the engine can be restarted in normal
operation.
For this vehicle anti-theft system, we summarize the following points, these points at the
beginning of our contact with this system are taking some detours, write out hope to be
helpful:
1: the engine computer must be reset, Do not reset if the theft is difficult to do
successfully.
2: Do not reset after a successful theft alone to match the box and the engine
computer, because the two control units are not recognized by the password. And to
select a matching set of the new system, so the password can be two system memory.
3: The key match well and VIN written after the recall after the match and then
choose to replace the engine ECU, let the engine ECU and security computer matching,
 A
C
SE
N
FO
after this point and Citroen cars to replace the engine computer and BSI pairing
somewhat similar.
4: During the above operation without replacing key chip.
5: The method matched set of keys after writing data to deal with this car does not
work, written after a set of data, as long as a power-theft case, the data will automatically
become immediately 5AA5 of that data, then remember Good password to connect with
the key code is not recognized.
6: Be sure to look at the engine computer data stream whether certification this
one, so you know the engine computer a good job no. There are a lot of friends doing
this when the car keys can be equipped with good, it is launching vain, in fact, and the
engine computer has not been certified.
7: Cancellation theft method is not feasible at this car, though written after the
data was able to cancel the alarm, the car can be a normal start, but before long burglar
will re-lock the time about a month or so and then cancel and then will lock.
8: Finally, when the car's spark plug replacement must be replaced with a resistor
spark plug factory, if you replace the spark plug with no resistance, the car cannot
exercise because of how long it will interfere with the anti-theft ignition strong trigger,
causing the car to launch vain.
FO
N
SE
C
A