Acer G195HQ

Service Guide

1
 Service Guide Version and Revision

Version Release Date Revision History Customer model TPV model

T89AM6D8MXAFH2
A00 Sep-10-2009 Initial Release G195HQ
T89AM5D8MXAFN2

2
Copyright
Copyright © 2009 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced,
Transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in
any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without
the prior written permission of Acer Incorporated.

Disclaimer
The information in this guide is subject to change without notice. Acer Incorporated makes no representations or
warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties
of merchantability or fitness for any particular purpose. Any Acer Incorporated software described in this manual is
sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not Acer
Incorporated, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any
incidental or consequential damages resulting from any defect in the software.

Intel is a registered trademark of Intel Corporation.

Pentium and Pentium II/III are trademarks of Intel Corporation.
Other brand and product names are trademarks and/or registered trademarks of their respective holders.

Trademarks
Acer is a registered trademark of Acer Incorporated.
All other trademarks are property of their respective owners.

Conventions
The following conventions are used in this manual:

Screen messages Denotes actual messages that appear on screen.

Note Gives bits and pieces of additional information related to the current topic.
Warning Alerts you to any damage that might result from doing or not doing specific actions.
Caution Gives precautionary measures to avoid possible hardware or software problems.
Important Remind you to do specific actions relevant to the accomplishment of procedures.

3
Preface

Before using this information and the product it supports, please read the following general information.
1. This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION decided
for Acer's "global" product offering. To better fit local market requirements and enhance product competitiveness,
your regional office may have decided to extend the functionality of a machine (e.g. add-on card, modem, or extra
memory capability). These LOCALIZED FEATURES will NOT be covered in this generic service guide. In such
cases, please contact your regional offices or the responsible personnel/channel to provide you with further
technical details.

2. Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information available on
your regional web or channel. If, for whatever reason, a part number change is made, it will not be noted in the
printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer office may have a
DIFFERENT part number code to those given in the FRU list of this printed Service Guide. You MUST use the list
provided by your regional Acer office to order FRU parts for repair and service of customer machines.

Warning: (For FCC Certified Models)

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.

Notice:

1. The changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
2. Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits.
3. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this
equipment. It is the responsibility of the user to correct such interference.
As ENERGY STAR® Partner our company has determined that this product meets the ENERGY STAR®
guidelines for energy efficiency.

Warning:
To prevent fire or shock hazard, do not expose the monitor to rain or moisture. Dangerous high voltages are present
inside the monitor. Do not open the cabinet. Refer servicing to qualified personnel only.

4
Precautions

z Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in
a wet basement.

z Do not place the monitor on an unstable trolley, stand, or table. If the monitor falls, it can injure a person and
cause serious damage to the appliance. Use only a trolley or stand recommended by the manufacturer or sold
with the monitor. If you mount the monitor on a wall or shelf, uses a mounting kit approved by the manufacturer
and follow the kit instructions.
z Slots and openings in the back and bottom of the cabinet are provided for ventilation. To ensure reliable
operation of the monitor and to protect it from overheating, be sure these openings are not blocked or covered.
Do not place the monitor on a bed, sofa, rug, or similar surface. Do not place the monitor near or over a radiator
or heat register. Do not place the monitor in a bookcase or cabinet unless proper ventilation is provided.
z The monitor should be operated only from the type of power source indicated on the label. If you are not sure of
the type of power supplied to your home, consult your dealer or local power company.
z The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug will fit
only into a grounded power outlet as a safety feature. If your outlet does not accommodate the three-wire plug,
have an electrician install the correct outlet, or use an adapter to ground the appliance safely. Do not defeat the
safety purpose of the grounded plug.

z Unplug the unit during a lightning storm or when it will not be used for long periods of time. This will protect the
monitor from damage due to power surges.

z Do not overload power strips and extension cords. Overloading can result in fire or electric shock.
z Never push any object into the slot on the monitor cabinet. It could short circuit parts causing a fire or electric
shock. Never spill liquids on the monitor.
z Do not attempt to service the monitor yourself; opening or removing covers can expose you to dangerous
voltages and other hazards. Please refer all servicing to qualified service personnel
z To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate
configured receptacles marked between 100 - 240V AC, Min. 5A.
z The wall socket shall be installed near the equipment and shall be easily accessible.

Special Notes on LCD Monitors

The following symptoms are normal with LCD monitor and do not indicate a problem.

Notes
z Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and
then turn it on again to make sure the flicker disappears.
z You may find slightly uneven brightness on the screen depending on the desktop pattern you use.
z The LCD screen has effective pixels of 99.99% or more. It may include blemishes of 0.01% or less such as a
missing pixel or a pixel lit all of the time.
z Due to the nature of the LCD screen, an afterimage of the previous screen may remain after switching the image,
when the same image is displayed for hours. In this case, the screen is recovered slowly by changing the image
or turning off the Power Switch for hours.

5
 Table of Contents

Chapter 1 Monitor Features ………………………………………… 7

Introduction ……………………………………… 7
Electrical Requirements ……………………………………… 8
LCD Monitor General Specification ……………………………………… 9
LCD Panel Specification ……………………………………… 11
Factory Preset Timing ……………………………………… 13
Monitor Block Diagram ……………………………………… 14
Main Board Diagram ……………………………………… 15
Power Board Diagram 16
Software Flow chart ……………………………………… 17
Main Board Layout ……………………………………… 19
Installation ……………………………………… 20

Chapter 2 Operating Instructions ……………………………………… 22

User Controls ……………………………………… 22

Front Panel Controls ……………………………………… 22
eColor Management (OSD) ……………………………………… 23
How to Adjust a Setting ……………………………………… 23
How to Optimize The DOS-Mode ……………………………………… 26
Enter into the factory mode ……………………………………… 26

Chapter 3 Machine Disassembly ……………………………………… 27

Chapter 4 Troubleshooting ……………………………………… 33

Chapter 5 Connector Information ……………………………………… 39

Chapter 6 FRU (Field Replacement Unit) List ……………………………………… 40

Exploded Diagram ……………………………………… 40

Chapter 7 Schematic Diagram ……………………………………… 45

6
Monitor Features Chapter 1
Introduction
Scope
This short specification describes the electrical, optical and functional performance requirements for a 47cm (18.5”)
TFT LCD color monitor with VGA&DVI compatible interface.

Description
The LCD monitor is designed with the latest LCD technology to provide a performance oriented product with no
radiation. This will alleviate the growing health concerns. It is also a space saving design, allowing more desktop
space, and comparing to the traditional CRT monitor, it consumes less power and gets less weight in addition MTBF
target is 50k hours or more.

Chart of G195HQ

Panel M185XW01
D-Sub 15pin;
Signal Interface
DVI 24pin(Dual-Input Model);
Sync Type Separate / Compatible

Color Temp User Adjust Support

DDC DDC2B

Speaker Option

Headphone Jack Option

Microphone Jack No

USB Hub No

Tilt / Swivel Yes /No

7
Electrical Requirements of G195HQ
Standard Test Conditions
All tests shall be performed under the following conditions, unless otherwise specified.

Warm up time 30 min.

AC supply voltage 220V± 5 , 50± 3 Hz

Ambient temperature 20°C ± 5°C

Humidity 50% ± 10%
Display mode 1366 x 768, 60 Hz, all white

e-color mode Set to “User” mode

Set to The value under user mode, which allows that the brightest
Contrast control two of 32 linear distributed gray-scales (0 700mv) can be
distinguished.

Color temperature 6500°K

Brightness control The value under user mode

Analog Input signal 700 mVss

Picture position and size Factory preset value,

Viewing angle 90 ° H and V

Viewing distance 40 cm for LCD performance, 20 cm for LCD failures

Ambient illumination Dark room < 1 cd/m2

Measurement systems
The units of measure stated in this document are listed below:
1 gamma = 1 nano tesla
1 tesla = 10,000 gauss
cm = in x 2.54
Lb = kg x 2.2
Degrees F = [°C x 1.8] + 32
Degrees C = [°F - 32]/1.8
u' = 4x/(-2x + 12y + 3)
v' = 9y/(-2x + 12y + 3)
x = (27u'/4)/[(9u'/2) - 12v' + 9]
y = (3v')/[(9u'/2) - 12v' + 9]
nits = cd/(m2) = Ft-L x 3.426
lux = foot-candle x 10.76

8
LCD Monitor General Specification

Driving system TFT Color LCD

Pixel pitch 0.3(H) x 0.3(V)

LCD Panel Contrast Ratio 1000 : 1 (typ)

Response time 5ms(Typ.). 8ms(max)

Luminance of White 250 cd/m2(Typ.)

Separate Sync. H/V TTL

Input H-Frequency 30kHz – 80kHz

V-Frequency 55-75Hz

Viewing angle H:170°/ V:160° ( type)(CR>10)

Display Colors 16.7M

Weight(with stand) 3.7KG

Weight(without stand) 3.36KG

Dimension(with stand) 452.59(H)x 348.90(V) x 173.80(D) (mm)

Dimension(without stand) 452.59(H)x 288.95(V) x 60.00(D) (mm)

Display mode 1366 x 768 @60Hz

ON Mode < 37W

EPA ENERGY STAR®
OFF Mode < 1W

Set to The value under user mode, which allows that the brightest two of 32 linear
Contrast control
distributed gray-scales (0 700mv) can be distinguished.

Power Source 100 V ~ 240 V 50 ± 3Hz, 60 ± 3Hz

Operating Temp: 0° to 40°C

Storage Temp: -20° to 60°C
Environmental Operating Humidity: 15% to 90%
Considerations Storage Humidity: 15% to 90%
Operating Altitude: 12,000 feet
Storage Altitude: 40,000 feet

Peak surge current < 55A peak at 240 VAC and cold starting

Power line surge No advance effects (no loss of information or defect)

9
 452.59 mm 60.00 mm

G195HQ

288.95 mm
348.90 mm

261.18 mm 173.80 mm

10
LCD Panel Specification of G195HQ
This specification applies to the 18.5 inch-wide Color a-Si TFT-LCD Module M185XW01.The display supports the
WXGA - 1366(H) x 768(V) screen format and 16.7M colors (RGB 6-bits +Hi-FRC data). All input signals are
1-channel LVDS interface and this module doesn’t contain an inverter board for backlight.
General Specifications

Block Diagram
TFT LCD Module

11
Optical Specifications

12
Factory Preset Timing of G195HQ

13
Monitor Block Diagram
The LCD MONITOR will contain a main board, a power board, and a key board which house the flat panel control
logic, brightness control logic and DDC.
The power board will provide AC to DC Inverter voltage to drive the backlight of panel and the main board chips
each voltage.

CCFL Drive. Flat Panel and

CCFL backlight

Main Board
Power Board

AC-IN
100V-240V
Key board DVI Signal D-SUB Signal
(Dual-Input model)

14
Main Board Diagram
T89AM6D8MXAFH2 (Dual-Input Model)
Crystal 14.31818MHZ Panel Interface
(X401) (CN301)

Flash Memory Scalar IC TSUMU5PEHL-LF

EN25F20 Key control Interface
(Include MCU, ADC, OSD)
(U402)
(U401) (CN402)

H sync
D-Data
V sync
D-Clock
RGB
DVI D-Sub
Connector Connector
(CN102) (CN101)

T89AM5D8MXAFN2

Crystal 14.31818MHZ Panel Interface

(CN301)
(X401)

Scalar IC TSUM1PEL
Flash Memory Key control Interface
EN25F20 (Include MCU, ADC, OSD)
(U402) (U401) (CN402)
H sync
V sync
RGB

D-Sub
Connector
(CN101)

15
Power Board Diagram

AC input 14.5V
Bridge
EMI filter Rectifier Transformer Rectifier
and Filter diodes
5V

Start Resistor
(R908)

Feedback
PWM Control Circuit
Power Switch
(U901)
(Q901)

Photo coupler
(U902)

Output Transformer MOSFET 14.5V

Circuit (T801) (Q803)
Lamp

5V
PWM Control
Feedback AM9000ES ON/OFF
Circuit
(U801) DIM

16
Software Flow Chart

Y
2 3
N
N

N
5

N
7 8
Y

Y 9

N
10 11

N N
12 13

Y Y

N
14 15 16

17

N
18 19

17
Remark:

1) MCU initializes.

2) Is the EEPROM blank?

3) Program the EEPROM by default values.

4) Get the PWM value of brightness from EEPROM.

5) Is the power key pressed?

6) Clear all global flags.

7) Are the AUTO and SELECT keys pressed?

8) Enter factory mode.

9) Save the power key status into EEPROM.

Turn on the LED and set it to green color.
Scalar initializes.

10) In standby mode?

11) Update the lifetime of back light.

12) Check the analog port, are there any signals coming?

13) Does the scalar send out an interrupt request?

14) Wake up the scalar.

15) Are there any signals coming from analog port?

16) Display "No connection Check Signal Cable" message. And go into standby mode after the
message disappears.

17) Program the scalar to be able to show the coming mode.

18) Process the OSD display.

19) Read the keyboard. Is the power key pressed?

18
Main Board Layout
715G2883 1 6

Symbol Description Symbol Description

TSUM1PEL PQFP-100
U401 TSUMU5PEHL-LF CN302 WAFER
PQFP-100(Dual-Input Model)
U701 AP1117E33L-13 CN701 CONNECTOR 9P 2.0

U106 AZC099-04S SOT23-6L CN402 CONN 6PIN 2.0

U103 AZC099-04S SOT23-6L CN101 D-SUB 15PIN VERTICAL CONN WITH SCREW

DVI 24PIN CONN F ATTACHED

U402 EN25F20-100GCP 2Mb SOP-8 CN102
SCREW(Dual-Input Model)

U104 AZC099-04S SOT23-6L U105 AZC099-04S SOT23-6L(Dual-Input Model)

X401 14.31818MHZ/32PF/49US U107 AZC099-04S SOT23-6L(Dual-Input Model)

AZC099-04S SOT23-6L(Dual-Input
U106
Model)

19
Installation
To install the monitor to your host system, please follow the steps as given below:
Steps
1. 1-1 Connect Video Cable
a. Make sure both the monitor and computer are powered-OFF.
b. Connect the VGA video cable to the computer.
1-2 Digital Cable (Only Dual-Input Model)
a. Make sure both the monitor and computer are powered-OFF.
b. Connect one end of the 24-pin DVI cable to the back of the monitor and connect the other end to the
computer’s port.
1-3 Connect one end of the 19-pin HDMI cable to the back of the monitor and connect the other end to the
computer’s port(Optional).
2. Connect the Audio Cable (Only Audio-Input Model)(Optional)
3. Connect power cord
Connect the power cord to the monitor, then to a properly grounded AC outlet.
4. Power-ON Monitor and Computer
Power-ON the monitor first, then power-ON the computer. This sequence is very important.
5. If the monitor still does not function properly, please refer to the troubleshooting section to diagnose the problem.

20
Attaching / Removing the Base

Attaching:
Align the base with the stand and push the base towards the top of the monitor.

Removing:
Depress the release hooks as indicated first before removing the base and follow the arrow direction to remove it.

Screen Position Adjustment

To optimize the viewing position, you can adjust the monitor tilt by using both of your hands to hold the edges of the
monitor as shown below. The monitor can be adjusted to 15 degrees up or 5 degrees down.

21
Operating Instructions Chapter 2
Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the
monitor. By changing these settings, the picture can be adjusted to your personal preferences.
• The power cord should be connected.
• Connect the video cable from the monitor to the video card.
• Press the power button to turn on the monitor position. The power indicator will light up.
User Controls

Power Switch / Power LED:

To turn the monitor ON or OFF.
Lights up to indicate the power is turned ON.

Using the Shortcut Menu

Press the function button to open the shortcut menu. The shortcut menu lets you quickly select the most commonly
accessed settings.

Empowering:
Press the Empowering Key to open the Acer eColor Management OSD and access the scenario modes.
AUTO Auto Adjust:
Press this button to activate the Auto Adjustment function. The Auto Adjustment function is used to set the HPos,
VPos, Clock and Focus.
MENU OSD functions
Press this button to activate the OSD menu.
Volume Up / Down
Press to adjust volume (Only Audio-Input Model)(Optional)
INPUT Input Key
Use Input key to select from different video sources that may be connected to your monitor.
(a) VGA input (b) DVI input (c) HDMI input
As you cycle through the sources you will see the following messages on right top side of screen to indicate
currently selected input source. It may take 1 or 2 seconds for the image to appear.
VGA or DVI or HDMI
If either VGA or DVI input is selected ,but the VGA and DVI cables are not connected, a floating dialog box indicates:
“No Cable Connect” or “No Signal”

22
eColor Management (OSD)

Operation instructions
Step 1: Press “ ”Key to open the Acer eColor Management OSD and access the scenario modes
Step 2: Press “ ” or “ ” to select the mode
Step 3: Press “ AUTO “ Key to confirm the mode and exit the eColor menu.
Features and Benefits

Adjusting the OSD settings

The OSD can be used for adjusting the settings of your LCD Monitor.Press the MENU key to open the OSD. You
can use the OSD to adjust the picture quality, OSD position and general settings. For advanced settings,please refer
to following page:
Adjusting the picture quality

23
1 Press the MENU key to bring up the OSD.

2 Using the keys, select Picture from the OSD. Then navigate to the picture element you wish to adjust.
3 Use the / keys to adjust the sliding scales.
4 The Picture menu can be used to adjust the current Brightness, Contrast,Colour Temp, Auto Config and other
image-related qualities.
Adjusting the OSD position

1 Press the MENU key to bring up the OSD.

2 Using the directional keys, select OSD from the on screen display.Then navigate to the feature you wish to
adjust.
Adjusting the setting

1 Press the MENU key to bring up the OSD.

2 Using the keys, select Setting from the OSD. Then navigate to the feature you wish to adjust.
3 The Setting menu can be used to adjust the screen Menu Language and other important settings.

24
Product information

1 Press the MENU key to bring up the OSD.

2 Using the keys, select Information from the OSD. Then the basic information of LCD monitor will show
up for current input.

25
How to Optimize The DOS-Mode
Plug And Play
Plug & Play DDC2B Feature
This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the
monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional
information about its display capabilities.

The DDC2B is a bi-directional data channel based on the I²C protocol. The host can request EDID information over
the DDC2B channel.

This monitor will appear to be non-functional if there is no video input signal. In order for this monitor to
operate properly, there must be a video input signal.

This monitor meets the Green monitor standards as set by the Video Electronics Standards Association (VESA)
and/or the United States Environmental Protection Agency (EPA) and The Swedish Confederation Employees
(NUTEK). This feature is designed to conserve electrical energy by reducing power consumption when there is no
video-input signal present. When there is no video input signals this monitor, following a time-out period, will
automatically switch to an OFF mode. This reduces the monitor's internal power supply consumption. After the video
input signal is restored, full power is restored and the display is automatically redrawn. The appearance is similar to
a "Screen Saver" feature except the display is completely off. Pressing a key on the keyboard, or clicking the mouse
restores the display.

Using the Right Power Cord

The accessory power cord for the Northern American region is the wallet plug with NEMA 5-15 style and is UL listed
and CSA labeled. The voltage rating for the power cord shall be 125 volts AC.
Supplied with units intended for connection to power outlet of personal computer: Please use a cord set consisting of
a minimum No. 18 AWG, type SJT or SVT three conductors flexible cord. One end terminates with a grounding type
attachment plug, rated 10A, 250V, and CEE-22 male configuration. The other end terminates with a molded-on type
connector body, rated 10A, 250V, having standard CEE-22 female configuration.
Please note that power supply cord needs to use VDE 0602, 0625, 0821 approval power cord in European counties.

Enter into the factory mode:

Turn off the power, press the “e-color” and turn the power on. The factory OSD will be at the left top of the panel.

26
Machine Disassembly Chapter 3
This chapter contains step-by-step procedures on how to disassemble the monitor-
G195HQ for maintenance.
The tool for disassembly is as follows:
Screwdriver, Hexagonal screwdriver, Putty knife.

Disassembly Procedure
1.Lay the monitor on a flat, soft and clean surface.

2.Press the button remarked in green the remove the base.

3. Remove the two piece of cover hinge and the four screws remarked in red to remove the hinge assembly.

27
4.Remove the rear cover.
Pry the monitor up then find out the hooks’ position, use the tool (like the picture or other card) to insert into the
gap of bezel and rear cover.

28
Turn over the monitor and take off the rear cover.

4. Remove the bezel.

Disconnect the connector remarked in green.
PS: be careful to Disconnect the Key board connector, because the keyboard connector maybe damage.

The cable connect

the main board and
key board

29
Remove the 2 screws remarked in red.

Remove the lamp connectors to remove the panel. Put attention to the LVDS cable.

LVDS CABLE

30
6. Turn over the main frame and remove the four screws remarked in red and disconnected remarked in green to
remove the main board and power board.

Power board
Main board

Remove the speakers.(Optional)

31
7.The panel

32
Troubleshooting Chapter 4
This chapter provides troubleshooting information for the G195HQ:
1.Main Board
1) No Power

No power

Press power key and look if the

picture is normal

NG

Please reinsert and make sure the

AC of 100-240 is normal

OK NG Reinsert or check the

power section

Measure U701 Pin2=3.3V, C704 (+) =1.8V

NG
OK Check U701, Q702 and Q703

Check if X401 oscillate waveforms are

normal

NG
Replace X401 OK

Replace U401

33
2) No Picture (LED is orange)

No picture

The button if under NG NG

X401 oscillate
control waveform is normal Replace X401

OK
OK
Check reset circuit of NG Check Correspondent
U401 is normal component
Measure U701 Pin2=3.3V,
C704(+)=1.8V
OK

Replace U401
OK

X401 oscillate NG
waveform is normal

Check U701, Q702 and Q703

NG
Replace X401
OK

Check HS/VS from

CN101 is normal

NG
Check Correspondent
OK component

Replace U401

34
 3) Panel Power Circuit

White screen

NG
Measure Q302 base X401 oscillate
is low level? waveform is normal

OK NG Replace X401
OK

Check CN301 is solder

and Q302, Q301 is OK? Check reset circuit of
U401 is normal

NG Check Correspondent
NG
Check Correspondent
component.
component. OK

OK
Replace U401

Replace PANEL

35
2. Key Board

OSD is unstable or not working

NG
Is Key Pad Board connecting normally? Connect Key Board

NG
Is Button Switch normally? Replace Button Switch

NG
Is Key Pad Board normally? Replace Key Board

Check Main Board

36
3. Power Board

1) No power

Check CN902 PIN6, 7 = 5V

NG

Check AC line volt 110V or 220V

OK NG
Check AC input

Check the voltage of C907 (+)

OK NG
Check bridge rectified circuit and F902 circuit

Check start voltage for the pin8 of U901

NG
OK Check R908 and Change U901

Check the auxiliary voltage is bigger than

11V and smaller than 25V

OK NG
1) Check U901
2) Check D907/Q901 circuit

Check U901 pin5 PWM wave

OK
NG
Check U901

Check D902/ Q906/Q904/U902/ZD901/U903

37
2.) No Backlight

Check C811(+)=14.5V

NG
Check adapter or MB
OK

Check ON/OFF signal

NG
Check Interface board
OK

Check U801 PIN11,14 have the output of square wave at short time

NG
Change U801
OK

Check Q803 PIN5, 6, 7, 8 have the output of square wave at short time.

NG
Check Q803
OK

Check the output of T801

NG
Change T801
OK

Check connecter & lamp

38
Connector Information Chapter 5
D-sub connect and DVI connect:

15-Pin Color Display Signal Cable

24-Pin Color Display Signal Cable (Dual-Input Model)

39
FRU (Field Replaceable Unit) List Chapter 6
This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of G195HQ. Refer to this
chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization).

NOTE: Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information
available on your regional web or channel (http://aicsl.acer.com.tw/spl/). For whatever reasons a part number
change is made, it will not be noted in the printed Service Guide. For ACER AUTHORIZED SERVICE
PROVIDERS, your Acer office may have a DIFFERENT part number code from those given in the FRU list of
this printed Service Guide. You MUST use the local FRU list provided by your regional Acer office to order
FRU parts for repair and service of customer machines.

NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or regulations on
how to dispose it properly, or follow the rules set by your regional Acer office on how to return it.

Exploded Diagram (Model: G195HQ)

40
Item Description TPV Part No. Acer Part No. Q`ty
1 BEZEL L185WA-9acer5 A34G1522AEMA1B0130 60.LJM0B.001 1
2 KEY BUTTON A33G0779AEM 1L0100 N/A 1
3 POWER BUTTON A33G0780AEM 1L0100 N/A 1
4 LENS A33G0768 1 1C0100 N/A 1
A15G0933101401
60.LJM0B.008
5 MAINFRAME 1
A15G0933101301 (Dual-Input
60.LJM0B.009 (Dual-Input Model)
Model)
A34G1523AEM 4B0100
60.LJM0B.002
REAR COVER
6 1
L205WA-9ACER5-S5 A34G1523AEM 3B0100
60.LJM0B.003 (Dual-Input Model)
(Dual-Input Model)
7 HINGE A37G0137 1 60.LJM0B.004 1
8 STAND FRONT A34G1524AEM 1B0100 60.LJM0B.005 1
9 STAND REAR A34G1525AEM 1B0100 60.LJM0B.006 1
10 HINGE COVER A33G0772AEM 1L0100 60.LJO0B.004 2
11 BASE A34G1521AEM 1B0100 60.LJM0B.007 1
12 BRAKET BASE A15G0932101 N/A 1
13 RUBBER Q12G6300 95 N/A 6
14 POWER BOARD PWPC9821AQMY 55.LJM0B.003 1
756GQ9CB BA256 00
55.LJM0B.001
15 MAIN BOARD 1
756GQ9CB BA255 00
55.LJM0B.002 (Dual-Input Model)
(Dual-Input Model)
16 KEY BOARD KEPC9QKO 55.LJO0B.002 1
SCREW(FOR PB/MAIN
S1 0G1G1130 8120 N/A 3
FRAME)
SCREW,(FOR MB/MAIN
S2 0G1G1130 8120 N/A 1
FRAME)
SCREW(FOR
S3 0Q1G1740 12120 N/A 4
HINGE/REAR COVER)
S4 SCREW 0M1G 140 6125 N/A 4
S5 SCREW (T3X6) 0Q1G 130 6120 N/A 6

41
Part List
Above picture show the description of the following component.

Picture Description TPV Part No. Acer Part No.

A15G0933101401 60.LJM0B.008

60.LJM0B.009
Main_frame
A15G0933101301 (Dual-Input
(Dual-Input Model) Model)

Bezel A34G1522AEMA1B0130 60.LJM0B.001

Panel 750GLU185X1414N000 LK.18005.016

A34G1523AEM 4B0100 60.LJM0B.002

60.LJM0B.003
Rear Cover
A34G1523AEM 3B0100 (Dual-Input
(Dual-Input Model) Model)

Power Board PWPC9821AQMY 55.LJM0B.003

42
 756GQ9CB BA256 00
55.LJM0B.001

55.LJM0B.002
Main Board 756GQ9CB BA255 00
(Dual-Input
(Dual-Input Model)
Model)

Key Board KEPC9QKO 55.LJO0B.002

Hinge A37G0137 1 60.LJM0B.004

60.LJM0B.007
Base A34G1521AEM 1B0100

Bracket Base A15G0932101 N/A

LVDS ASS'Y 095G8018 3XH60 50.LEF0B.002

43
D-SUB Cable 089G 728CAA DB 50.LAL0B.002

DVI Cable
(Dual-Input 089G1748HAA AC 50.LAN0B.003
Model)

Power Cord 089G404A18N CX 50.LBT0B.004

44
Schematic Diagram Chapter 7
Main Board
T89AM6D8MXAFH2 (Dual-Input Model)
FB102

MVCC_1 VGA_B+ 1 2 R105 100R 1/16W 5% C102

BEAD 0.047uF DSUB_B+ 2

1
H_Sy nc R102 0R05 1/10W 5% R103 1K 1/16W 5% R108 C105
DSUB_H 2
V_Sy nc R104 1K 1/16W 5% 5pF/50V
DSUB_V 2
D109 75R 1/16W 5%

R106 R107 C103 C104 BAT54C VGA_B- R109 100R 1/16WC106

5%
DSUB_B- 2
0.047uF
2K2 1/16W 5% 2K2 1/16W 5% 22pF 22pF

3
U104 ESD_VCC R110 470R 1/16W 5% C107
DSUB_5V DSUB_SOG 2
DSUB_SCL 1 6 H_Sy nc FB103 1000pF
2 I/O1 I/O4 5
CN101 DSUB_SDA 3 GNDVDD 4 V_Sy nc VGA_G+ 1 2 R111 100R 1/16W 5% C108
FB107 I/O2 I/O3 BEAD 0.047uF DSUB_G+ 2

16
R101 10 AZC099-04S C112 R112 C109
DDC1_SCL DSUB_SCL 15 5 VGA_PLUG NC 5pF/50V
2 DDC1_SCL
9 DSUB_5V 300 OHM 75R 1/16W 5%
100R 1/16W 5% 14 4 U10 3
8 VGA_B- C124 VGA_G- R114 100R 1/16W 5% C110
0.1uF 16V DSUB_G- 2
13 3 VGA_B+ ZD104 0.047uF
R113 7 VGA_G- RLZ5.6B ZD105
DDC1_SDA DSUB_SDA 12 2 VGA_G+ RLZ5.6B
2 DDC1_SDA U103
6 VGA_R- ESD_VCC
100R 1/16W 5% 11 1 VGA_R+ VGA_G+ 1 6 FB101
2 I/O1 I/O4 5
DB15 VGA_R+ 3 GNDVDD 4 VGA_B+ VGA_R+ 1 2 R115 100R 1/16W 5%C111
I/O2 I/O3 DSUB_R+ 2
17

BEAD 0.047uF

AZC099-04S C101 R116

NC C113
75R 1/16W 5% 5pF/50V
U10 1
VGA_R- R117 100R 1/16W 5%
C114
DSUB_R- 2
0.047uF
CMVCC DSUB_5V

1
CN102 DVI_5V D104
8 DVI_5V
VSY NC 15 DVI_HPD BAT54C
SYNC GND 6 R118 100R 1/16W 5% DDC2_SCL
DDC SCL DDC2_SCL 2
7 R119 100R 1/16W 5% DDC2_SDA
DDC SDA DDC2_SDA 2
14 R120 10K 1/16W 5% R140
+5V 16

3
HPD NC R123 C116
11 C115 R121 NC NC
1/3shield 3 R122 HDCP_CTRL R124 R125
2/4shield 19 0.1uF/16V NC 2 4K7 1/16W 5% 4K7 1/16W 5% U101
0/5shield 22 Q101 NC 8 1
clk shield NC 7 VCC A0 2
18 R126 10R 1/16W 5% RX0P DDC1_SCL 6 WP A1 3
DAT0+ RX0P 2 SCL A2
17 R127 10R 1/16W 5% RX0N DDC1_SDA 5 4
DAT0- RX0N 2 SDA VSS
10 R128 10R 1/16W 5% RX1P DDC_WP
DAT1+ RX1P 2 2
9 R129 10R 1/16W 5% RX1N
DAT1- RX1N 2
2 R130 10R 1/16W 5% RX2P NC / M24C02-WMN6TP
DAT2+ RX2P 2
1 R131 10R 1/16W 5% RX2N
DAT2- RX2N 2 CMVCC FB104 FB105 DVI_5V
13
DAT3+ 12
DAT3- 5
DAT4+ 4
DAT4-

1
21 300 OHM 300 OHM
DAT5+ 20 C121 D108 C122
DAT5- 23 R132 10R 1/16W 5% RXCP 1000pF BAT54C
clk+ RXCP 2 1000pF
24 R134 10R 1/16W 5% RXCN VCC3.3
GND
GND

clk- RXCN 2

JACK
26
25

U107 ESD_VCC2 U105 ESD_VCC1 U106 ESD_VCC1 ESD_VCC

3
AZC099-04S AZC099-04S AZC099-04S FB108 R133
1 6 1 6 1 6 10K 1/16W 5% C117
2 I/O1 I/O4 5 2 I/O1 I/O4 5 2 I/O1 I/O4 5 1 2 R136
3 GNDVDD 4 3 GNDVDD 4 3 GNDVDD 4 300 OHM R137 R138 NC
I/O2 I/O3 I/O2 I/O3 I/O2 I/O3 DVI_HPD R135 10K 1/16W 5% NC U102
C120 C118 C119 4K7 1/16W 5% 4K7 1/16W 5% 8 1
7 VCC A0 2
NC NC NC VGA_PLUG R139 6K8 1/16W 5% DET_CABLE 2 DDC2_SCL 6 WP A1 3
DDC2_SDA 5 SCL A2 4
SDA VSS
U10 7 U10 5 U10 6 2 DDC_WP
GND POWER DGND NC / M24C02-WMN6TP

T P V ( Top Victory Electronics Co . , Ltd. ) OEM MODEL Acer G185H Dual Only Size B
ESD_VCC2 FB109 ESD_VCC1
G2883-1-6-X-37-090901 TPV MODEL CBPC9M6AFQH Rev E
1 2
300 OHM Key Component 2.0.INPUT PCB NAME
< >
Date Tuesday , September 01, 2009 Sheet 2 of 6

45
 CN301

LVB0M RXO0- 30
PA[0..9] LVB0P RXO0+ 29
2 PA[0..9]
LVB1M RXO1- 28
PA0 LVA3P LVB1P RXO1+ 27
PA1 LVA3M LVB2M RXO2- 26
PA2 LVACKP LVB2P RXO2+ 25
PA3 LVACKM 24
PA4 LVA2P LVBCKM RXOC- 23
PA5 LVA2M CN302 LVBCKP RXOC+ 22
PA6 LVA1P LVB3M RXO3- 21
PA7 LVA1M LVB3P RXO3+ 20
PA8 LVA0P LVA0M RXE0- 13 14 RXE0+ LVA0P LVA0M RXE0- 19
PA9 LVA0M LVA1M RXE1- 11 12 RXE1+ LVA1P LVA0P RXE0+ 18
LVA2M RXE2- 9 10 RXE2+ LVA2P 17
PB[0..9] LVACKM RXEC- 7 8 RXEC+ LVACKP LVA1M RXE1- 16
2 PB[0..9]
PB0 LVB3P LVA3M RXE3- 5 6 RXE3+ LVA3P LVA1P RXE1+ 15
PB1 LVB3M 3 4 14
PB2 LVBCKP 1 2 LVA2M RXE2- 13
PB3 LVBCKM LVA2P RXE2+ 12
PB4 LVB2P LVACKM RXEC- 11
PB5 LVB2M CONN LVACKP RXEC+ 10
PB6 LVB1P PANEL_VCC LVA3M RXE3- 9
PB7 LVB1M LVA3P RXE3+ 8
PB8 LVB0P 7
PB9 LVB0M 6
5
4
PANEL_VCC 3
2
1
CMVCC

NC/CONN
U301 R301 C301
1 8
R303 C302 2 S D 7 330 OHM 1/4W 0.1uF/16V
3 S D 6
10K 1/16W 5% 0.1uF/16V 4 S D 5
R304 G D
R302 NC\AO4411
Q301
4K7 1/16W 5% 47K 1/16W 5% AO3401
C303

NC

Q302 C304
2 PPWR_ON# 2N3906S-RTK/PS PANEL_VCC
NC
3D R305

0 OHM +-5% 1/8W

1 2
G S + C305

AO3401L 100uF25V

T P V ( Top Victory Electronics Co . , Ltd. ) OEM MODEL Acer G185H Dual Only Size A

G2883-1-6-X-37-090901 TPV MODEL CBPC9M6AFQH Rev E

Key Component 3.0.OUTPUT PCB NAME
< >
Date Tuesday , September 01, 2009 Sheet 3 of 6

46
 CMVCC

VCC1.8
C710
0.1uF 16V
FB702
300 OHM
CN701 VCC3.3
C705 + C704
1 SM340A
2 D701 MVCC 0.1uF/16V 100uF25V
3 CMVCC Q702
4 CMVCC KN2907AS R705
5 BKLT-VBRI R709
6 BKLT-EN R710 NC NC 10K 1/16W 5%
7 PANEL_ID#
PANEL_ID# 2
8 Volume# FB704 Q703 R706
Volume# 2
9 Mute KN2907AS BKLT-VBRI
Mute 2 adj_BACKLIGHT 2
VCC3.3
NC 1K 1/16W 5%

CONN C713 C701 R708

lock type NC C712 NC/2.2 OHM 2W
0.1uF/16V NC
R701
0R05 1/4W
DGND 1,2,3

VCTRL

DVI_5V DSUB_5V

1
D702

VCC3.3 VCC3.3 D702 External EDID NC

BAT54C

MVCC_1 Internal EDID BAT54C

R702
3

10K 1/16W 5% R703

FB701
BKLT-EN 10K 1/16W 5% FB703 C711 R701 R708 U701
300 OHM
C702 0.1uF 16V NC
MVCC VCC3.3 TSUM5PFHL 0R05 1/4W NC 223
NC R704
U701
on_BACKLIGHT 2
3 2 TSUMU58EHL NC 3.3 OHM 2W 223
Q701 4K7 1/16W 5% VIN VOUT

VSS
2N3904S-RTK/PS
C707 TSUMO58CWHL NC 3.3 OHM 2W 252
+ C706 C708 AP1117E33LA C709 +

1
100uF25V 0.1uF/16V 0.1uF/16V 100uF25V

T P V ( Top Victory Electronics Co . , Ltd. ) OEM MODEL Acer G185H Dual Only Size B

G2883-1-6-X-37-090901 TPV MODEL CBPC9M6AFQH Rev E

Key Component 4.0.POWER PCB NAME
< >
Date Tuesday , September 01, 2009 Sheet 4 of 6

47
 VCC1.8 VDDC
VDDP FB403 VCC3.3 FB401 AVDD VCC3.3 FB402 VPLL
VCC3.3
4 VCC1.8
0 OHM +-5% 1/8W C412 300OHM 300OHM
1 VCC3.3
C409 C408
+ C403 C404 C406
C402 C410 C411 0.1uF/16V C407 0.1uF/16V
10uF/50V 0.1uF/16V C405 0.1uF/16V
0.1uF/16V VDVI VMPLL VPLL AVDD VDDP VDDC 0.1uF/16V 0.1uF/16V
0.1uF/16V 0.1uF/16V 0.1uF/16V

VCC3.3 FB404 VMPLL

14

98

16

24

32
49
56
75

51
66
82

34
8
VCC3.3 VDVI
81 VCC3.3

AVDD_MPLL

AVDD_PLL

VDDP
VDDP
VDDP
VDDP
AVDD_ADC

VDDC
VDDC
VDDC

VDDC
AVDD_DVI
AVDD_DVI
VCTRL VCTRL
300OHM R403
54 PA0 0 OHM +-5% 1/8W
23 LVA3P 55 PA1
1 DSUB_R+ RIN0P LVA3M
22 58 PA2 C414 C415
1 DSUB_R- RIN0M LVACKP
20 59 PA3 R402 0.1uF/16V 0.1uF/16V
1 DSUB_G+ GIN0P LVACKM
19 60 PA4 C413
1 DSUB_G- GIN0M LVA2P
21 61 PA5 NC 0.1uF/16V
1 DSUB_SOG SOGIN0 LVA2M
18 62 PA6
1 DSUB_B+ BIN0P LVA1P
17 63 PA7 R404 NC
1 DSUB_B- BIN0M LVA1M
27 64 PA8 Q405
1 DSUB_H HSY NC0 LVA0P
28 65 PA9 NC
1 DSUB_V VSYNC0 LVA0M
30
1 DDC1_SDA DDCA_SDA/RS232_TX
31 LF_B
1 DDC1_SCL DDCA_SCL/rs232_RX
3 R405 NC
1 RX2P R+
4
1 RX2N R-
6 PA[0..9] DVI_5V
1 RX1P G+ PA[0..9] 3 DDC_WP 1
7
1 RX1N G- R447
9 R406
1 RX0P B+
10 67 PB0 PB[0..9] Q401
1 RX0N B- LVB3P PB[0..9] 3
12 68 PB1 NC
1 RXCP CK+ LVB3M
13 69 PB2 NC
1 RXCN CK- LVBCKP
100 70 PB3 NC R407 C416
1 DDC2_SDA DDCD_SDA LVBCKM
1 71 PB4 R446
1 DDC2_SCL DDCD_SCL LVB2P 72 PB5 NC NC
LVB2M 73 PB6 NC
LVB1P 74 PB7
15 LVB1M 77 PB8
AVDD
R401 390 OHM 1/16W REXT LVB0P 78 PB9 MVCC
LVB0M
0.1uF/16V 26 TSUMU5PEHL-LF 36 CMVCC
C417 REFP NC 45 R448
VCC3.3 NC 46
25 NC Q406 10K 1/16W 5%
REFM 41 EE_WP
GPIO_P23 42
C401 GPIO_P22 AO3401
35 R445 NC/100R 1/16W 5%
U402 GPIO_P15/PWM0 PANEL_ID# 4
0.22uF16V 47 R409 100R 1/16W 5% WP R410
R412 1 8 37 PWM2/GPIO_P24
CS# VCC SDO LVDS
10K 1/16W 5% 2 7 38 85 6K8 1/16W 5%
DO HOLD# SCZ GPIO_P12 on_BACKLIGHT 4
WP 3 6 39 86
WP# CLK SCK PWM1/GPIO_P25 adj_BACKLIGHT 4
4 5 40 R449
VSS DI SDI 87
48 RSTN 88 R415 100R 1/16W 5% KEY1 47K1/16W
EN25F20-100GCP
3 PPWR_ON# GPIO_P27/PWM1 GPIO_P00/SAR1 89 R416 100R 1/16W 5% KEY2 C418 R413
C419 GPIO_P01/SAR2 90 R417 100R 1/16W 5%
GPIO_P02/SAR3 DET_CABLE 1 0.1uF/16V 10K 1/16W 5%
84 Reduce the luminance of LED-090901
+

MVCC RST 91 R419 1K1/16W LED_GRN/BLUE

10UF50V GPIO_P06 92 R420 620R 1/16W 5% LED_ORANGE
R421 GPIO_P07 93 R422 NC
R423 PWM0/GPIO_P26 94
GPIO_P13 HDCP_CTRL 1
100K 1/16W 5% 0R05 1/16W 96 95 R424 NC R426 CMVCC
XIN GPIO_P14 Mute 4
2

C420 47pF 99 R425 100R 1/16W 5% POWER_KEY#

GPIO_P16/PWM2 VCC3.3
X401
CMVCC 14.31818MHz 10K 1/16W 5%
97
C421 47pF XOUT R427
+

7 CMVCC
R428 100R 1/16W 5%
C437 NC/10K 1/16W 5%
10UF50V C422 0.1uF/16V80
R450 BY PASS
R430
100K 1/16W 5% NC FB406
44 R429 NC MSCL Volume#
GPIO_P10/I2C_MCL 4
43 R431 NC MSDA
GPIO_P11/I2C_MDA NC
52
53 MODE[0] Q404
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND

MODE[1] NC
11
29
33
50
57
76
79
83
2
5

VCC3.3

VCC3.3
R444 R443
CN402 3.9K OHM 1% 1/16W 3.9K OHM 1% 1/16W

C423 1 KEY2
R440 R441 R442 2 KEY1
U403 NC 3 POWER_KEY #
NC NC NC 8 1 4 LED_GRN/BLUE
EE_WP 7 VCC NC 2 5 LED_ORANGE
MSCL 6 WC E1 3 6
MSDA 5 SCL E2 4 LF_B
SDA VSS C431 C432 C433 C434 R411 C435 R408
NC C436
CONN FB405 0.1uF/16V 0.1uF/16V 0.1uF/16V 0.1uF/16V 10K 1/16W 5% 0.1uF/16V 10K 1/16W 5%
NC NC

lock type

T P V ( Top Victory Electronics Co . , Ltd. ) OEM MODEL Acer G185H Dual Only Size C

G2883-1-6-X-37-090901 TPV MODEL CBPC9M6AFQH Rev E

Key Component 5.0.SCALER PCB NAME
< >
Date Tuesday , September 01, 2009 Sheet 5 of 6

48
T89AM5D8MXAFN2
FB102

VGA_B+ 1 2 R105 100R 1/16W 5% C102

BEAD 0.047uF DSUB_B+ 2

R108 C105
5pF/50V
75R 1/16W 5%

VGA_B- R109 100R 1/16WC106

5%
DSUB_B- 2
0.047uF

R110 470R 1/16W 5% C107

DSUB_SOG 2
FB103 1000pF

VGA_G+ 1 2 R111 100R 1/16W 5% C108

BEAD 0.047uF DSUB_G+ 2

R112 C109
5pF/50V
MVCC_1 75R 1/16W 5%

VGA_G- R114 100R 1/16W 5% C110

DSUB_G- 2

1
H_Sy nc R102 0R05 1/10W 5% R103 1K 1/16W 5% 0.047uF
DSUB_H 2
V_Sy nc R104 1K 1/16W 5%
DSUB_V 2
D109

R106 R107 C103 C104 BAT54C FB101

2K2 1/16W 5% 2K2 1/16W 5% 22pF 22pF VGA_R+ 1 2 R115 100R 1/16W 5%C111
BEAD DSUB_R+ 2
0.047uF

3
U104 ESD_VCC
DSUB_5V
DSUB_SCL 1 6 H_Sy nc R116
2 I/O1 I/O4 5 C113
CN101 DSUB_SDA 3 GNDVDD 4 V_Sy nc 75R 1/16W 5% 5pF/50V
FB107 I/O2 I/O3
16

VGA_R- R117 100R 1/16W 5%

C114
DSUB_R- 2
R101 10 AZC099-04S C112 0.047uF
DDC1_SCL DSUB_SCL 15 5 VGA_PLUG NC CMVCC DSUB_5V
2 DDC1_SCL
9 DSUB_5V 300 OHM
100R 1/16W 5% 14 4 U1 03

1
8 VGA_B- C124
13 3 VGA_B+ ZD104 0.1uF 16V D104
R113 7 VGA_G- RLZ5.6B ZD105
DDC1_SDA DSUB_SDA 12 2 VGA_G+ BAT54C
2 DDC1_SDA RLZ5.6B U103
6 VGA_R- ESD_VCC
100R 1/16W 5% 11 1 VGA_R+ VGA_G+ 1 6
2 I/O1 I/O4 5
DB15 VGA_R+ 3 GNDVDD 4 VGA_B+

3
I/O2 I/O3
17

R123 C116
NC NC
AZC099-04S C101 R124 R125
NC 4K7 1/16W 5% 4K7 1/16W 5% U101
8 1
7 VCC A0 2
U1 01
DDC1_SCL 6 WP A1 3
DDC1_SDA 5 SCL A2 4
SDA VSS
2 DDC_WP
NC / M24C02-WMN6TP

CMVCC

C121
VCC3.3 1000pF

R133
10K 1/16W 5%

VGA_PLUG R139 6K8 1/16W 5% DET_CABLE 2

GND POWER DGND

T P V ( Top Victory Electronics Co . , Ltd. ) OEM MODEL Acer G185H Analog Only Size B

G2883-1-6-X-42-090901 TPV MODEL CBPC9M5AFQN Rev E

Key Component 2.0.INPUT PCB NAME
< >
Date Tuesday , September 01, 2009 Sheet 2 of 6

49
 CN301

LVB0M RXO0- 30
PA[0..9] LVB0P RXO0+ 29
2 PA[0..9]
LVB1M RXO1- 28
PA0 LVA3P LVB1P RXO1+ 27
PA1 LVA3M LVB2M RXO2- 26
PA2 LVACKP LVB2P RXO2+ 25
PA3 LVACKM CN302 24
PA4 LVA2P LVBCKM RXOC- 23
PA5 LVA2M LVBCKP RXOC+ 22
PA6 LVA1P LVA0M RXE0- 13 14 RXE0+ LVA0P LVB3M RXO3- 21
PA7 LVA1M LVA1M RXE1- 11 12 RXE1+ LVA1P LVB3P RXO3+ 20
PA8 LVA0P LVA2M RXE2- 9 10 RXE2+ LVA2P LVA0M RXE0- 19
PA9 LVA0M LVACKM RXEC- 7 8 RXEC+ LVACKP LVA0P RXE0+ 18
LVA3M RXE3- 5 6 RXE3+ LVA3P 17
PB[0..9] 3 4 LVA1M RXE1- 16
2 PB[0..9]
PB0 LVB3P 1 2 LVA1P RXE1+ 15
PB1 LVB3M 14
PB2 LVBCKP LVA2M RXE2- 13
PB3 LVBCKM CONN LVA2P RXE2+ 12
PB4 LVB2P PANEL_VCC LVACKM RXEC- 11
PB5 LVB2M LVACKP RXEC+ 10
PB6 LVB1P LVA3M RXE3- 9
PB7 LVB1M LVA3P RXE3+ 8
PB8 LVB0P 7
PB9 LVB0M 6
5
4
PANEL_VCC 3
2
1
CMVCC

NC/CONN
U301 R301 C301
1 8
R303 C302 2 S D 7 330 OHM 1/4W 0.1uF/16V
3 S D 6
10K 1/16W 5% 0.1uF/16V 4 S D 5
R304 G D
R302 NC\AO4411
Q301
4K7 1/16W 5% 47K 1/16W 5% AO3401
C303

NC

Q302 C304
2 PPWR_ON# 2N3906S-RTK/PS PANEL_VCC
NC
3D R305

0 OHM +-5% 1/8W

1 2
G S + C305

AO3401L 100uF25V

T P V ( Top Victory Electronics Co . , Ltd. ) OEM MODEL Acer G185H Analog Only Size A

G2883-1-6-X-42-090901 TPV MODEL CBPC9M5AFQN Rev E

Key Component 3.0.OUTPUT PCB NAME
< >
Date Tuesday , September 01, 2009 Sheet 3 of 6

50
 CMVCC

VCC1.8
C710
0.1uF 16V
FB702
300 OHM
CN701 VCC3.3
C705 + C704
1 SM340A
2 D701 MVCC 0.1uF/16V 100uF25V
3 CMVCC Q702
4 CMVCC KN2907AS R705
5 BKLT-VBRI R709
6 BKLT-EN R710 NC NC 10K 1/16W 5%
7 PANEL_ID#
PANEL_ID# 2
8 Volume# FB704 Q703 R706
Volume# 2
9 Mute KN2907AS BKLT-VBRI
Mute 2 adj_BACKLIGHT 2
VCC3.3
NC 1K 1/16W 5%

CONN C713 C701 R708

lock type NC C712 NC/2.2 OHM 2W
0.1uF/16V NC
R701
0R05 1/4W
DGND 1,2,3

VCTRL

DVI_5V DSUB_5V

1
VCC3.3 VCC3.3 D702
BAT54C

MVCC_1
R702
3

10K 1/16W 5% R703

FB701
BKLT-EN 10K 1/16W 5% FB703 C711
300 OHM
C702 0.1uF 16V NC
MVCC VCC3.3
NC R704
U701
on_BACKLIGHT 2
3 2
Q701 4K7 1/16W 5% VIN VOUT

VSS
2N3904S-RTK/PS
C707
+ C706 C708 AP1117E33LA C709 +

1
100uF25V 0.1uF/16V 0.1uF/16V 100uF25V

T P V ( Top Victory Electronics Co . , Ltd. ) OEM MODEL Acer G185H Analog Only Size B

G2883-1-6-X-42-090901 TPV MODEL CBPC9M5AFQN Rev E

Key Component 4.0.POWER PCB NAME
< >
Date Tuesday , September 01, 2009 Sheet 4 of 6

51
 VCC1.8 VDDC
VDDP FB403 VCC3.3 FB401 AVDD VCC3.3 FB402 VPLL
VCC3.3
4 VCC1.8
0 OHM +-5% 1/8W C412 300OHM 300OHM
1 VCC3.3
C409 C408
+ C403 C404 C406
C402 C410 C411 0.1uF/16V C407 0.1uF/16V
10uF/50V 0.1uF/16V C405 0.1uF/16V
0.1uF/16V VDVI VMPLL VPLL AVDD VDDP VDDC 0.1uF/16V 0.1uF/16V
0.1uF/16V 0.1uF/16V 0.1uF/16V

VCC3.3 FB404 VMPLL

14

98

16

24

32
49
56
75

51
66
82

34
8
VCC3.3 VDVI
81 VCC3.3

AVDD_33
AVDD_33

AVDD_33

AVDD_33

AVDD_33

VDDP
VDDP
VDDP
VDDP

VDDC
VDDC
VDDC

VDDC
VCTRL VCTRL
300OHM R403
54 PA0 0 OHM +-5% 1/8W
23 LVA3P 55 PA1
1 DSUB_R+ RIN0P LVA3M
22 58 PA2 C414 C415
1 DSUB_R- RIN0M LVACKP
20 59 PA3 R402 0.1uF/16V 0.1uF/16V
1 DSUB_G+ GIN0P LVACKM
19 60 PA4 C413
1 DSUB_G- GIN0M LVA2P
21 61 PA5 NC 0.1uF/16V
1 DSUB_SOG SOGIN0 LVA2M
18 62 PA6
1 DSUB_B+ BIN0P LVA1P
17 63 PA7 R404 NC
1 DSUB_B- BIN0M LVA1M
27 64 PA8 Q405
1 DSUB_H HSYNC0 LVA0P
28 65 PA9 NC
1 DSUB_V VSYNC0 LVA0M
30
1 DDC1_SDA DDCA_SDA/RS232_TX
31 LF_B
1 DDC1_SCL DDCA_SCL/rs232_RX
3 R405 NC
1 RX2P NC
4
1 RX2N NC
6 PA[0..9] DVI_5V
1 RX1P NC PA[0..9] 3 DDC_WP 1
7
1 RX1N NC R447
9 R406
1 RX0P NC
10 67 PB0 PB[0..9] Q401
1 RX0N NC LVB3P PB[0..9] 3
12 68 PB1 NC
1 RXCP NC LVB3M
13 69 PB2 NC
1 RXCN NC LVBCKP
100 70 PB3 NC R407 C416
1 DDC2_SDA NC LVBCKM
1 71 PB4 R446
1 DDC2_SCL NC LVB2P 72 PB5 NC NC
LVB2M 73 PB6 NC
LVB1P 74 PB7
15 LVB1M 77 PB8
AVDD
R401 390 OHM 1/16W REXT LVB0P 78 PB9 MVCC
LVB0M
0.1uF/16V 26 TSUM1PEL 36 CMVCC
C417 REFP GPIO_P40 45 R448
VCC3.3 GPIO_P41 46
25 GPIO_P42 Q406 10K 1/16W 5%
REFM 41 EE_WP
GPIO_P23 42
C401 GPIO_P22 AO3401
35 R445 NC/100R 1/16W 5%
U402 GPIO_P22/PWM0 PANEL_ID# 4
0.22uF16V 47 R409 100R 1/16W 5% WP R410
R412 1 8 37 PWM2/GPIO_P24
CS# VCC SDO LVDS
10K 1/16W 5% 2 7 38 85 6K8 1/16W 5%
DO HOLD# SCZ GPIO_P12 on_BACKLIGHT 4
WP 3 6 39 86
WP# CLK SCK PWM1/GPIO_P25 adj_BACKLIGHT 4
4 5 40 R449
VSS DI SDI 87
48 GPIO_P17/SAR0 88 R415 100R 1/16W 5% KEY1 47K1/16W
EN25F20-100GCP
3 PPWR_ON# GPIO_P27/PWM1 GPIO_P00/SAR1 89 R416 100R 1/16W 5% KEY2 C418 R413
C419 GPIO_P01/SAR2 90 R417 100R 1/16W 5%
GPIO_P02/SAR3 DET_CABLE 1 0.1uF/16V 10K 1/16W 5%
84 Reduce the luminance of LED-090901
+

MVCC RST 91 R419 1K1/16W LED_GRN/BLUE

10UF50V GPIO_P06 92 R420 620R 1/16W 5% LED_ORANGE
R421 GPIO_P07 93 R422 NC
R423 PWM0/GPIO_P26 94
GPIO_P13 HDCP_CTRL 1
100K 1/16W 5% 0R05 1/16W 96 95 R424 NC R426 CMVCC
XIN GPIO_P14 Mute 4
2

C420 47pF 99 R425 100R 1/16W 5% POWER_KEY#

GPIO_P16/PWM2 VCC3.3
X401
CMVCC 14.31818MHz 10K 1/16W 5%
97
C421 47pF XOUT R427
+

7 CMVCC
R428 100R 1/16W 5%
C437 NC/10K 1/16W 5%
10UF50V C422 0.1uF/16V80
R450 BY PASS
R430
100K 1/16W 5% NC FB406
44 Volume#
GPIO_P10/I2C_MCL 4
43
GPIO_P11/I2C_MDA NC
52
53 MODE[0] Q404
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND

MODE[1] NC
11
29
33
50
57
76
79
83
2
5

VCC3.3

VCC3.3
R444 R443
CN402 3.9K OHM 1% 1/16W 3.9K OHM 1% 1/16W

C423 1 KEY 2
R440 R441 R442 2 KEY 1
U403 NC 3 POWER_KEY#
NC NC NC 8 1 4 LED_GRN/BLUE
EE_WP 7 VCC NC 2 5 LED_ORANGE
MSCL 6 WC E1 3 6
MSDA 5 SCL E2 4 LF_B
SDA VSS C431 C432 C433 C434 R411 C435 R408
NC C436
CONN FB405 0.1uF/16V 0.1uF/16V 0.1uF/16V 0.1uF/16V 10K 1/16W 5% 0.1uF/16V 10K 1/16W 5%
NC NC

lock type

T P V ( Top Victory Electronics Co . , Ltd. ) OEM MODEL Acer G185H Analog Only Size C

G2883-1-6-X-42-090901 TPV MODEL CBPC9M5AFQN Rev E

Key Component 5.0.SCALER PCB NAME
< >
Date Tuesday , September 01, 2009 Sheet 5 of 6

52
Power board
! R929 100 OHM 1/4W

1
BD901 C916 F801
KBP208G R930 100 OHM 1/4W 0.001uF 0R05 1/4W 5% +14.5V
+

2
2 3 R903 100 OHM 1/4W
ZD901
R904 MTZJ T-72 16B
D901 + C918 220 OHM 2W
-

NC/SR5150 1000UF25V

1
1 2
R905
4

D902 470R 1/10W 5%

R906
! 1
SB5150
2
Q904
2SD1207T
100KOHM +-5% 2WS T901
! ! C911 POWER X'FMR R907
R931 C937 1500PF2KV 6 C923 1K 1/10W 1%
NC ! ! 12 R909 100 OHM 1/4W 0.001uF
11
C909 0.01uF/2KV D903 C917 L906
NC/0.22uF/275V
R932
+ C907
82uF 450V
! R908
10K OHM 1/4W +-5%
FR107 5
7
R910 100 OHM 1/4W 0.001uF F901 FUSE +5V

NC 8
D904 R912 100 OHM 1/4W + 1000uF M 16V
3 L901 4 ! 1000PF/250VAC FR103 4
2 10
C925
+ C920
C938 9 1000UF25V + C922
! R913 D905 NC/31DQ06FC3 470uF 16V
2 1 + C913 1.5 OHM 1/4W +-5%
R933 22uF/50V 1
30mH NC D906

2
D907 1 3
D908 R921 IN4148
NC/IN4148 NC/100K 1/10W 1% U901
1 8 FMW-2156

R900
R901
620K OHM 1/4W R902
2 CT
3 COMPNC
HV 7
6
R917
10R 1/4W 5%
!Q901
4 CS VCC 5 FMA07N65GX
C927 GNDOUT R919
620K OHM 1/4W 620K OHM 1/4W LD7576 150R 1/8W 5%
0.047uF

1
R934 C912 R918
! NC 0.1uF/25V 10K 1/10W 1%
FB901
BEAD

1
R920
C908 1K 1/10W 1%
0.47uF/275V C914 R923 U902

2
NR901 470pF 220 OHM 1/4W PC123X2YFZOF
NTCR

2
R914
! 43.2K OHM 1% 1/4W
R924 C924
0.39 OHM 2W +-5% 0.1uF/16V
F902
FUSE R916
3.65K OHM 1% 1/10W
R928
1K 1/10W 1%

C902 C903
C900
U903
1000pF 1000pF C915 KIA431A-AT/P
0.0022UF R925
2.43K OHM 1% 1/10W
R935
! NC

!
3

2 1 CN902

L907
CN901 9 F903 NC
SOCKET MUTE 8 +5V1
HS1 HS2 VOL 7
+5V
HEAT SINK(Q901) NC/HEAT SINK(D906_5V/4A) 6
5
1 1 4 + C921 + C931
2 2 3 NC/1000uF25V NC/470uF/16V
ON/OFF
2
C926 1
DIM
0.1uF/16V

Wire Harness
HS3 GND1
HEAT SINK(D906_5V/2.5A) GND

1 1
2 2

T P V ( Top Victory Electronics Co . , Ltd. ) OEM MODEL ACER 22" LCD Size Custom

G2892-2-3-X-21-090817 TPV MODEL PWPC9821AQMY Rev 1

Key Component 01.POWER PCB NAME 715G2892-2-3
ODM MODEL
Date Saturday , August 15, 2009 Sheet 2 of 3

53
 REF

+14.5V
+ C811
470uF 25V R805
10K 1/10W 5% CN801

C814 R803
1uF 25V 1
R816 2 CONN
0.1uF50V C801 LI1
10 OHM +-5% 1/10W 5pF6KV 2K 1/10W 5%
R807
T801
RJ805 OV2
R811 6 7
POWER X'FMR
C815
DIM
R815 10K 1/10W 5% C802
10K 1/10W 5% C809 0R05 1/4W 5% 0.0022uF/50V
C813
0.001uF 10 OHM +-5% 1/10W 3 R801
D803
4 412 OHM 1/10W
2
R817 0.01uF AM9000ES 2N2 50V
C806 BAW56 3
ON/OFF Q803 1 8
C810 8 9 0.047uF RJ807 RJ803
10K 1/10W 5% 7 DBRT VIN 10 1
6 EN BT 11 4 5 RJ801
FSET TG 3 G2 D2 6
20K 1/10W 1% 5 12 S2 D2
R810 4 FT SW 13 R813 0R05 1/4W 5% 2 7 0R05 1/4W 5%
COMP VCC 1 G1 D1 8
3 14 S1 D1
R809 2 LI2 BG 15 3.3 OHM +-5% 1/10W 0R05 1/4W 5%
100K 1/10W 5% 1 LI1 GND 16
OV2 OV1 P8008HV
C808 REF
1uF 16V U801 C805 RJ806
C812 0R05 1/4W 5%
C807 R814
REF
0.0039uF/16V 1uF 16V R806
10K 1/10W 5% CN802
2N2 50V
10 OHM +-5% 1/10W
LI2 OV2 R812 R804
LI1 OV1 1
3.3 OHM +-5% 1/10W CONN
C803 2
LI2
5pF6KV 2K 1/10W 5% RJ802
R808
OV1 0R05 1/4W 5%
10K 1/10W 5%

C804 R802
0.0022uF/50V 412 OHM 1/10W

RJ804
0R05 1/4W 5%

T P V ( Top Victory Electronics Co . , Ltd. ) OEM MODEL Size Custom

G2892-2-3-X-21-090817 TPV MODEL PWPC9821AQMY Rev 1

Key Component 02.INVERTER PCB NAME 715G2892-2-3
ODM MODEL
Date Saturday , August 15, 2009 Sheet 3 of 3

54
Key board

ZD007 NC/UDZSNP5.6B
2 1
LED001
4 3

LED
2 1

2 1

ZD008 NC/UDZSNP5.6B

CN001
7

1 LBADC1 R002 2Kohm 1/10W +/-1%

2 LBADC2 LED_GRN#
3 DC_POWERON LED_RED#
4 LED_GRN#
5 LED_RED#
6
R004 2Kohm 1/10W +/-1%
CONN C001 C002 C003 C004 C005 R005 1K 1/10W 1%
NC NC 0.1uF 50V 0.1uF 50V NC
8

ECOLOR

AUTO
POWER

VOL+
MENU
VOL-
SW001

ZD006

ZD003

ZD004

ZD001

ZD002
C009

C007

ZD005
GND 1 2 1 2 1 2 1 3 1 2 1 2

C011

C010

C008

C006
SW006 SW003 SW004 SW002 SW005

NC/UDZSNP5.6B
SW 5 SW 5 SW 5 SW SW 5 SW 5

NC

NC
NC/UDZSNP5.6B

NC/UDZSNP5.6B

NC/UDZSNP5.6B

NC/UDZSNP5.6B

NC/UDZSNP5.6B
NC

NC

NC

NC
3 4 3 4 3 4 2 4 3 4 3 4
5

MENU(2K) 1.1V
GND
LBADC1
VOL- (GND) 0 V
VOL+(2K) 1.1V
LBADC2
AUTO(1K) 0.65V
ECOLOR(GND) 0 V

CN001

CONNECTOR LED POWER ECOLOR AUTO MENU VOL- VOL+

TPV ( Top Victory Electronics Co . , Ltd. ) OEM MODEL G series Size B

G3573-1-X-X-2-20090629 TPV MODEL ACER Rev 1

Key Component 02.Key Board PCB NAME 715G3573-1
< >
Date Thursday , July 09, 2009 Sheet 2 of 2

55