Comp Micom error codes for Knob type Models LGE Internal Use Only

❑ Inverter Comp ❑ Linear Comp

LED
Trip Cause
LED Blinking
Trip Cause
Blinking
Sensing Error 1 Micom sensing circuit problem
Sensing error 1 Micom sensing circuit problem
Over Stroke 2 Stroke error detect
Over Voltage 2 Over voltage detect
Miss Cable 3 Comp harness no connect detect
Miss Cable 3 Comp harness no connect detect
Over voltage 4 Over voltage detect
Comp Lock 5 Piston lock detect
Comp Lock 5 Piston lock detect
Over current 6 Over Current detect
Over current 6 Over Current detect
IPM Fault out 7 IPM arm short detect (IPM fault detect)
IPM Fault out 7 IPM arm short detect (IPM fault detect)
Communication 8 Communication error detect
Communication 8 Communication error detect

Note:
1. Non-Modified DC PCB with 4 capacitor LED blinking applicable from 1 to 8.
2. Modified DC PCB with Single capacitor LED blinking applicable only 1 time.
Frost Free – Inverter Compressor Status Indicator

Comp Status LED

Type -1

Type -2
1. Main Micom error codes for Knob type Models –FF Models

2. Main Micom error codes for Internal Display Non-Dual type Models- FF Models
Main Micom error codes for Internal Display Dual type Models -FF Models
FF- I_E-Micom Models
Alpha FF- E-Micom (GL-F502/572/432/442/682/681)
Alpha FF- E-Micom (GL-F502/572/432/442/682/681)
 SXS Error Code List

Resistance Measuring Method: Resistance Table

• sensor resistance tolerance : ± 5%
• Before measuring the resistance value of sensor, stabilize the sensor at any
particular temperature for over 3 min.
• Measures with digital meter
• Resistance can be measured at the PCB connection after removing the
sensor connection housing from MAIN PCB .

Temperature Resistance of R1,R2,RT Resistance Freezer

& Sensor
Defrost Sensor
-20 o C 77.0 K ohm 22.3 K ohm

-15 o C 60.0 K ohm 16.9 K ohm

-10 o C 47.3 K ohm 13.0 K ohm
-5 o C 38.4 K ohm 10.1 K ohm

0o C 30.0 K ohm 7.8 K ohm

5o C 24.1 K ohm 6.2 K ohm

10 o C 19.5 K ohm 4.9 K ohm

15 o C 15.9 K ohm 3.9 k ohm

20 o C 13 .0 K ohm 3.1 K ohm

25 o C 11.0 K ohm 2.5 K ohm

30 o C 8.9 K ohm 2.0 K ohm

40 o C 6.2 K ohm 1.4 K ohm

50 o C 4.3 K ohm 0.8 K ohm

SXS_Linear Compressor Defect Detection
Remedy based on the blink of LED

No. LED Operation Cause Remedy

LED repeat 1 time
Defective PCB 1. Reset power
1 parts
(micom)
2. Change PCB if same symptom continuously
occurs
Blink – Off – Blink – Off – Blink – Off – Blink – Off – Blink – Off ‥ repeat

LED repeat 2 times Defective PCB 1. 1. Reset power

2 parts
(excessive piston)
2. Change PCB if same symptom continuously
occurs
Blink–Blink – Off– Blink–Blink – Off– Blink–Blink – Off– ‥ repeat
LED repeat 3 times
1. Check power
Defective power 2. Reset power
3 Blink–Blink–Blink – Off – Blink–Blink–Blink – Off– ‥ repeat voltage 3. Change PCB if same symptom continuously
occurs
LED repeat 4 times Defective
1. Check connector of PCB and COMP
4 connection to
COMP cable
2. If nothing is affected, change PCB
Blink–Blink–Blink–Blink– Off – Blink–Blink–Blink –Blink – Off – ‥ repeat
LED repeat 5 times
1. Reset power
5 Locked piston 2. If same symptom continues, change PCB
3. If same symptom continues, change COMP
Blink–Blink–Blink–Blink–Blink – Off – Blink–Blink–Blink–Blink–Blink– Off – ‥ repeat
LED repeat 6 times
Circuit over 1. Reset power
6 Blink–Blink–Blink–Blink–Blink –Blink – Off – Blink–Blink–Blink–Blink–Blink –Blink – Off – ‥ repeat
current
Error
2. If same symptom continues, change PCB
3. If same symptom continues, change COMP
LED repeat 7 times Defective PCB
1. Reset power
7 parts
(IPM)
2. If same symptom continues, change PCB
Blink–Blink–Blink–Blink–Blink –Blink–Blink – Off – Blink–Blink–Blink–Blink–Blink –Blink–Blink – Off– ‥ repeat

LED repeat 8 times

Abnormal 1. Reset power
8 Communication 2. If same symptom continues, change PCB
Blink–Blink–Blink–Blink–Blink –Blink–Blink–Blink – Off – Blink–Blink–Blink–Blink–Blink –Blink–Blink–Blink – Off – ‥ repeat
2.Error code for PCB fault. SXS Models
2.1 Model: Universe
2.2 Model:Next8 SXS Models
2.3 Model: P-Veyron (GC-247 Models) SXS Models