Baluni Classes

(A Primer Institute for IIT-JEE, NEET)

Capacitor
Exercise-1
CAPACITANCE, ENERGY STORED IN CAPACITOR & SPHERICAL CAPACITOR
Q 1. The capacitance C of a capacitor is :
(1) independent of the charge and potential of the capacitor.
(2) directly proportional to charge on one plate.
(3) independent of the geometrical configuration of the capacitor.
(4) directly proportional to potential difference between plates.

Q 2. The capacitance of a spherical conductor of radius r is proportional to-

(1) r (2) 1/r (3) r2 (4) 1/r3

Q 3. To increase the charge on the plate of a capacitor implies to :-

(1) decrease the potential difference between the plates.
(2) decrease the capacitance of the capacitor.
(3) increase the capacitance of the capacitor.
(4) increase the potential difference between the plates.

Q 4. The energy of a charged capacitor resides in

(1) the electric field only-
(2) the magnetic field only
(3) both the electric and magnetic field
(4) neither in electric nor magnetic field
Q 5. The net charge on a capacitor is :-
(1) 2q (2) q/2 (3) 0 (4) infinity
Q 6. The earth has Volume 'V' and Surface area 'A' ; then its capacitance would be :
𝐴 𝑉 𝑉 𝐴
(1) 10 𝑉 (2) 40 𝐴 (3) 120 𝐴 (4) 120 𝑉
Q 7. The two parallel plates of a condenser have been connected to a battery of 300 V and the
charge collected at each plate is 1 C. The energy supplied by the battery is :
(1) 6 × 10–4 J (2) 3 × 10–4 J (3) 1.5 × 10–4 J (4) 4.5 × 10–4 J
Q 8. If the p.d. across the ends of a capacitor 4μF is 1.0 kilovolt. Then its electrical potential
energy will be-
(1) 4 × 10–3ergs (2) 2 ergs (3) 2 joules (4) 4 joules

Q 9. When a capacitor of value 200 F charged to 200V is discharged separately through

resistance of 2 ohms and 8 ohms, then heat produced in joule will respectively be:
(1) 4 and 16 (2) 16 and 4 (3) 4 and 8 (4) 4 and 4
Q 10. The potential to which a conductor is raised, depends on :-
(1) the amount of charge (2) the geometry and size of the conductor

Baluni Classes, 30, Bhagya Nagar, Between ISBT & Amar Ujala Press, Bye Pass Road, Agra. Ph. 9837919228.
2
 (3) both (1) and (2) (4) None of these

Q 11. The charge q on a capacitor varies with voltage as shown in figure. The area of the triangle
AOB represents :

(1) electric field between the plates (2) electric flux between the plates
(3) energy density (4) energy stored by the capacitor

Q 12. A 6μF capacitor charged from 10 volts to

20 volts. Increase in energy will be -
(1) 18 × 10–4 joule (2) 9 × 10–4 joule
(3) 4.5 × 10–4 joule (4) 9 × 10–9 joule

Q 13. An uncharged capacitor is connected to a battery. On charging the capacitor :-

(1) all the energy supplied is stored in the capacitor.
(2) half the energy supplied is stored in the capacitor.
(3) the energy stored depends upon the capacity of the capacitor only.
(4) the energy stored depends upon the time for which the capacitor is charged.

CYLINDRICAL CAPACITOR PARALLEL PALTE CAPACITOR & EFFECT OF DIELECTRIC SLAB

Q 14. The capacity of parallel plate condenser depends on:
(1) the type of metal used
(2) the thickness of plates
(3) the potential difference applied across the plates
(4) the separation between the plates.

Q 15. If the maximum circumference of a sphere is 2 m, then its capacitance in water would be :-
(Dielectric constant of water = 81)
(1) 27.65 pF (2) 2385 pF (3) 236.5 pF (4) 2865 pF

Q 16. The capacity of a parallel plate condenser is C. Its capacity when the separation between the
plates is halved will be-
(1) 4C (2) 2C (3) C/2 (4) C/4

Baluni Classes, 30, Bhagya Nagar, Between ISBT & Amar Ujala Press, Bye Pass Road, Agra. Ph. 9837919228. 3
Q 17. A parallel plate capacitor has rectangular plates of 400 cm2 area and are separated by a
distance of 2 mm with air as the medium. What charge will appear on the plates if a 200 volt
potential difference is applied across the capacitor ?
(1) 3.54 × l0–6 C (2) 3.54 × 10–8 C
(3) 3.54 × l0–10 C (4) 1770.8 × l0–13 C

Q 18. There are two metallic plates of a parallel plate capacitor. One plate is given a charge +q
while the other is earthed as shown. Points P, P1 and P2 are taken as shown in adjoining
figure. Then the electric intensity is not zero at :

(1) P only (2) P1 only (3) P2 only (4) P, P1 and P2

Q 19. The distance between the plates of a circular parallel plate capacitor of diameter 40 mm,
whose capacity is equal to that of a metallic sphere of radius 1m will be :
(1) 0.01 mm (2) 0.1 mm (3) 1.0 mm (4) 10 mm

Q 20. The energy density in a parallel plate capacitor is given as 2.1 × 10–9 J/m3. The value of the
electric field in the region between the plates is :
(1) 2.1 Nc–1 (2) 21.6 NC–1 (3) 72 Nc–1 (4) 8.4 Nc–1

Q 21. A parallel plate condenser has a capacitance 50μF in air and 110 μF. When immersed in an
oil. The dielectric constant K of the oil is-
(1) 0.45 (2) 0.55 (3) 1.10 (4) 2.20

Q 22. A charged parallel plate capacitor of distance (d) has U0 energy. A slab of dielectric constant
(K) and thickness (d) is then introduced between the plates of the capacitor. The new energy
of the system is given by:
𝑈0 𝑈
(1) KU0 (2) K2U0 (3) 𝐾
(4) 𝐾02

Q 23. The capacity and the energy stored in a parallel plate condenser with air between its plates
are respectively C0 and W0. If the air is replaced by glass (dielectric constant = 5) between
the plates, the capacity of the plates and the energy stored in it will respectively be -
𝑊0 C0 𝐶0 𝑊0
(1) 5C0 , 5W0 (2) 5C0 , 5
(3) , 5W0 (4) ,
5 5
5

Q 24. Distance between the plates of a parallel plate capacitor is 'd' and area of each plate is A.
When a slab of dielectric constant K and thickness t is placed between the plates, its capacity
becomes:

Baluni Classes, 30, Bhagya Nagar, Between ISBT & Amar Ujala Press, Bye Pass Road, Agra. Ph. 9837919228. 4
 𝜀0 𝐴 𝜀0 𝐴 𝜀0 𝐴 𝜀0 𝐴
(1) 1 (2) 1 (3) 1 (4) 1
[𝑑+𝑡{1− }] [𝑑+𝑡{1+ }] [𝑑−𝑡{1+ }] [𝑑−𝑡{1− }]
𝐾 𝐾 𝐾 𝐾

Q 25. By inserting a plate of dielectric material between the plates of a parallel plate capacitor, the
energy is increased five times. The dielectric constant of the material is -
(1) 1/25 (2) 1/5 (3) 5 (4) 25

Q 26. When a slab of dielectric medium is placed between the plates of a parallel plate capacitor
which is connected with a battery, then the charge on plates in comparison with earlier
charge:
(1) is less (2) is same
(3) is more (4) depends on the nature of the material inserted

Q 27. A glass slab is put within the plates of isolated charged parallel plate condenser. Which of
the following quantities does not change ?
(1) energy of the condenser (2) capacity
(3) intensity of electric field (4) charge

Q 28. A parallel plate capacitor is connected to a battery and a dielectric slab is inserted between
the plates, then which quantity increase :
(1) potential difference (2) electric field
(3) stored energy (4) E.M.F. of battery
Q 29. A parallel plate capacitor is connected to a battery and inserted a dielectric plate between
the place of plates then which quantity increase-
(1) potential difference (2) electric field
(3) stored energy (4) E. M . F of battery

Q 30. A parallel plate capacitor is connected to a battery and decreased the distance between the
plates then which quantity is same on the parallel plate capacitor-
(1) potential difference
(2) capacitance
(3) intensity of electric field
(4) stored energy

Q 31. A parallel plate capacitor is connected with a battery whose potential difference remains
constant. If the plates of the capacitor are shifted apart then the intensity of electric field :
(1) decreases and charge on plates also decreases.
(2) remains constant but charge on plates decreases.
(3) remains constant but charge on the plates increases.
(4) increases but charge on the plates decreases.

Q 32. A parallel plate capacitor is charged with a battery and afterwards the battery is removed. If
now, with the help of insulating handles, the distance between the plates is increased, then
(1) charge on capacitor increases and capacity decreases.

Baluni Classes, 30, Bhagya Nagar, Between ISBT & Amar Ujala Press, Bye Pass Road, Agra. Ph. 9837919228. 5
 (2) potential difference between the plates increases.
(3) capacitor of capacitor increases.
(4) value of energy stored in capacitor decreases.

Q 33. A parallel plate capacitor has a capacity C. The separation between plates is doubled and a
dielectric medium is inserted between plates. The new capacity is 3C. The dielectric
constant of medium is-
(1) 1.5 (2) 3.0 (3) 6.0 (4) 12.0

Q 34. A parallel plate air capacitor has a capacitance C. When it is half filled with a dielectric of
dielectric constant 5, the percentage increase in the capacitance will be :-

(1) 400% (2) 66.6% (3) 33.3% (4) 200%

COMBINATION OF CAPACITORS & SHARING OF CHARGES

Q 35. Three capacitors each of capacitance 1μF are connected in parallel. To this combination a
fourth capacitor of capacitance 1μF connected in series. The resultant capacitance of the
system is-
(1) 4μF (2) 2 μF (3) 4/3 μF (4) 3/4 μF

Q 36. the equivalent capacitance between the points A and B in the given diagram is :

8 3
(1) 8 F (2) 6 F (3) 3 F (4) 8 F

Q 37. Two capacitances of capacity C1 and C2 are connected in series and potential difference V is
applied across it. Then the potential difference across C1 will be-
𝐶 𝐶1 +𝐶2 𝐶2 𝐶1
(1) V 𝐶2 (2) V 𝐶1
(3) V𝐶 (4) V 𝐶
1 1 +𝐶2 1 +𝐶2

Q 38. Two condensers of capacity 0.3μF and 0.6μF respectively are connected in series. The
combination is connected across a potential of
6 volts. The ratio of energies stored by the condensers will be -
(1) 1/2 (2) 2 (3) 1/4 (4) 4

Baluni Classes, 30, Bhagya Nagar, Between ISBT & Amar Ujala Press, Bye Pass Road, Agra. Ph. 9837919228. 6
Q 39. A number of capacitors, each of capacitance 1 F and each one of which gets punctured if a
potential difference just exceeding 500 volt is applied, are provided. Then an arrangement
suitable for giving a capacitor of capacitance 3 F across which 2000 volt may be applied
requires at least :
(1) 4 component capacitors (2) 12 component capacitors
(3) 48 component capacitors (4) 16 component capacitors

Q 40. In the following circuit the resultant capacitance between A and B is 1μF. Then value of C is-
C 1µF
A
8µF 6µF
4µF

2µF 12µF
2µF
B
32 11 23 32
(1) 11μF (2) 32μF (3) 32μF (4) 23 μF

Q 41. The effective capacity of the network between terminals A and B is :

(1) 6 F (2) 20 F (3) 3 F (4) 10 F

Q 42. The value of equivalent capacitance of the combination shown in figure, between the points
P and Q is:

(1) 3C (2) 2C (3) C (4) C/3

Q 43. The equivalent capacitance between points A and B of the circuit shown will be :

Baluni Classes, 30, Bhagya Nagar, Between ISBT & Amar Ujala Press, Bye Pass Road, Agra. Ph. 9837919228. 7
 2 5 8 7
(1) F (2) F (3) F (4) F
3 3 3 3

Q 44. The equivalent capacity in the system of capacitance will be-

1.5µF

3µF 3µF

1.5µF
(1) 1μF (2) 2μF (3) 1.5 μF (4) 3μF

Q 45. The effective capacitance between the points P and Q of the arrangement shown in the
figure is :

(1) (1/2) F (2) 1 F (3) 2 F (4) 1.33 F

Q 46. Two spheres of radii R1 and R2 having equal charges are joined together with a copper wire.
If V is the potential of each sphere after they are separated from each other, then the initial
charge on both spheres was :
𝑉 𝑉 𝑉 𝑉 (𝑅 𝑅 )
(1) 𝑘 (R1 + R2) (2) 2𝑘 (R1 + R2) (3) 3𝑘 (R1 + R2) (4) 𝑘 (𝑅 1+𝑅2 )
1 2

Q 47. Three equal capacitors, each with capacitance C are connected as shown in figure. Then the
equivalent capacitance between A and B is -
C C C
A B

(1) C (2) 3C (3) C/3 (4) 3C/2

Q 48. Two spheres of radii 1 cm and 2 cm have been charged with 1.5 × 10–8 and 0.3 × 10–7
coulombs of positive charge. When they are connected with a wire, charge :
(1) will flow from the first to the second
(2) will flow from the second to the first
(3) will not flow at all
(4) may flow either from first to second, or from the second to first, depending upon the
length of the connecting wire

Q 49. Half of the space between a parallel plate capacitor is filled with a medium of dielectric
constant K parallel to the plates. If initially the capacity was C, then the new capacity will be:
(1) 2KC/(1+K) (2) C (K+1)/2 (3) CK/(1+K) (4) KC

Baluni Classes, 30, Bhagya Nagar, Between ISBT & Amar Ujala Press, Bye Pass Road, Agra. Ph. 9837919228. 8
Q 50. Two identical parallel plate capacitors are connected in series and then joined with a battery
of 100 V. A sheet of dielectric constant 4.0 is inserted between the plates of second
capacitor.
The potential difference across the capacitors will be respectively :
(1) 50 V, 50 V (2) 80 V, 20 V (3) 20 V, 80 V (4) 75 V, 25 V

Q 51. If three capacitors each of capacity 1μF are connected in such a way that the resultant
capacity is 1.5μF then-
(1) all the three are connected in series
(2) all the three are connected in parallel
(3) two of them are in parallel and then connected in series to the third
(4) two of them are in series and then connected in parallel to the third

Q 52. Two capacitances C1 and C2 in a circuit are joined as shown in figure. The potential of point A
is V1 and that of B is V2. The potential of point D will be :

1 𝐶2 𝑉1 +𝐶1 𝑉2 𝐶1 𝑉1 +𝐶2 𝑉2 𝐶2 𝑉1 −𝐶1 𝑉2

(1) (V1 + V2) (2) (3) (4)
2 𝐶1 +𝐶2 𝐶1 +𝐶2 𝐶1 +𝐶2

Q 53. A circuit has a section AB as shown in the figure with E = 10 V, C1 = 1.0 F, C2 = 2.0 F and
the potential difference VA – VB = 5 V. The voltage across C1 is :

(1) zero (2) 5 V (3) 10 V (4) 15 V

Q 54. Two capacitances C1 and C2 are connected in series; assume that C1 < C2. The equivalent
capacitance of this arrangement is C, where :
(1) C < C1/2 (2) C1/2 < C < C1 (3) C1 < C < C2 (4) C2 < C < 2C2

CHARGING AND DISCHARGING OF CAPACITORS & CAPACITOR’S CIRCUIT

Q 55. A capacitor of capacitance 5 F is connected as shown in the figure. The internal resistance
of the cell is 0.5. The amount of charge on the capacitor plate is :

(1) 0 (2) 5 C (3) 10 C (4) 25 C

Q 56. Calculate the charge on the plates of the capacitor C in the given circuit -

Baluni Classes, 30, Bhagya Nagar, Between ISBT & Amar Ujala Press, Bye Pass Road, Agra. Ph. 9837919228. 9
 E r

C R1
A B
R2
𝐸𝑅2 𝐸𝑅1 𝐸𝑅1 .𝑅2 𝐸𝑅1
(1) C × (2) C × (3) C × (4) C ×
𝑅2 +𝑟 𝑅1 +𝑟 𝑅1 +𝑅2 𝑅2 +𝑟

Q 57. In the given circuit, the potential difference across 3 F capacitor will be :

(1) 16 V (2) 10 V (3) 6 V (4) 4 V

Q 58. If potential of A is 10 V, then potential of B is :

(1) 25/3 V (2) 50/3 V (3) 100/3 V (4) 50 V

Q 59. A capacitor of capacitance 100µF is charged by connecting it to a battery of emf 12V and
internal resistance 2 ohm. The time taken before 99% of the maximum charge is stored on
the capacitor-
(1) 0.92 ms (2) 0.4 ms (3) 0.8 ms (4) 0.1 ms

Q 60. Capacitance C1 = 2C2 = 2C3 and potential difference across C1, C2 and C3 are V1, V2 and V3
respectively then :

(1) V1 = V2 = V3 (2) V1 = 2V2 = 2V3 (3) 2V1 = V2 = V3 (4) 2V1 = 2V2 = V3

Q 61. In the circuit shown in figure, the battery is an ideal one with emf V. The capacitor is initially
uncharged switch S is closed at time t = 0.

Baluni Classes, 30, Bhagya Nagar, Between ISBT & Amar Ujala Press, Bye Pass Road, Agra. Ph. 9837919228. 10
 The final charge Q on the capacitor is :
𝐶𝑉 𝐶𝑉 𝐶𝑉
(1) 2
(2) 3
(3) CV (4) 6

Q 62. A bulb, a capacitor and a battery are connected together as shown here, with switch S
initially open. When the switch S is closed, which one of the following is true ?

(1) The bulb will light up for an instant when the capacitor starts charging.
(2) The bulb will light up when the capacitor is fully charged
(3) The bulb will not light up at all
(4) The bulb will light up and go off at regular intervals.

Q 63. The capacity of a parallel plate air capacitor is 10 F. As shown in the figure this capacitor is
divided into two equal parts; these parts are filled by media of dielectric constants K1 = 2 and
K2 = 4. Capacity of this arrangement will be :

(1) 20 F (2) 30 F (3) 10 F (4) 40 F

Q 64. Two conducting spheres of radii R1 and R2 are charged with charges Q1 and Q2 respectively.
On bringing them in contact there is :
(1) no change in the energy of the system
(2) an increase in the energy of the system if Q1R2  Q2R1
(3) always a decrease in the energy of the system
(4) a decrease in the energy of the system if Q1R2  Q2R1

Q 65. A capacitor is charged with a battery and energy stored is U. After disconnecting the battery
another capacitor of same capacity is connected in parallel with it. The energy stored in each
capacitor is:
(1) U/2 (2) U/4 (3) 4 U (4) 2 U

Baluni Classes, 30, Bhagya Nagar, Between ISBT & Amar Ujala Press, Bye Pass Road, Agra. Ph. 9837919228. 11
Q 66. Three capacitors of capacitances 3 F, 10 F and 15 F are connected in series to a voltage
source of 100 V. The charge on 15 F is :
(1) 50 C (2) 160 C (3) 200 C (4) 280 C

Q.67 The resultant capacitance between (A) and (B) in the following figure is -
A
3µF 3µF 3µF
2µF 2µF 3µF

B
3µF 3µF 3µF
(1)1μF (2) 3μF (3) 2μF (4) 1.5μF

Q 68. The charge on each capacitors shown in figure and the potential difference across them will
be respectively :-

(1) 240 C, 80 C, 160 C and 80 V, 40 V, 40 V

(2) 300 C, 75 C, 150 C and 40 V, 80 V, 60 V
(3) 220 C, 70 C, 140 C and 60V, 50 V, 40 V
(4) none of these

Q 69. Two charged spheres having radii a and bare joined with a wire then the ratio of electric field
Ea/Eb on their respective surfaces is :
(1) a / b (2) b / a (3) a2 / b2 (4) b2 / a2

Q 70. A solid conducting sphere of radius R1 is surrounded by another concentric hollow

conducting sphere of radius R2. The capacitance of this assembly is proportional to :
𝑅2 −𝑅1 𝑅2 +𝑅1 𝑅 𝑅 𝑅 𝑅
(1)
𝑅1 𝑅2
(2) 𝑅1 𝑅2
(3) 𝑅 1+𝑅2 (4) 𝑅 1−𝑅2
1 2 2 1

Q 71. Two spherical conductors A and B of radius a and b (b > a) are placed in air concentrically. B
is given a charge + Q coulombs and A is grounded. The equivalent capacitance of these is :
𝑎𝑏 𝑏2
(1) 40 (2) 40 (a + b) (3) 40b (4) 40
(𝑏 − 𝑎) (𝑏−𝑎)

Q 72. Energy per unit volume for a capacitor having area A and separation d kept at potential
difference V is given by :
1 𝑉2 1 𝑉2 𝜀0 𝑉 2 𝐴2 1 𝑉 2 𝐴2
(1) 2 ∈0 𝑑2
(2) 2∈ 2 (3) 2𝑑 2
(4) 2 𝜀 2
0𝑑 0𝑑

Baluni Classes, 30, Bhagya Nagar, Between ISBT & Amar Ujala Press, Bye Pass Road, Agra. Ph. 9837919228. 12
Q 73. A conductor of capacitance 0.5F has been charged to 100 volts. It is now connected to
uncharged conductor of capacitance 0.2F. The loss in potential energy is nearly -
(1) 7 × 10–4 J (2) 3.5 × 10–4 J (3) 14 × 10–4 J (4) 7 × 10–3 J

Q 74. A conducting sphere of radius 10 cm is charged with 10 C. Another uncharged sphere of
radius 20 cm is allowed to touch it for some time. After that, if the spheres are separated,
then surface density of charge on the spheres will be in the ratio of :
(1) 1 : 4 (2) 1 : 3 (3) 2 : 1 (4) 1 : 1

Q 75. Two capacitors of capacitances 3 F and 6 F are charged to a potential of 12 V each. They
are now connected to each other with the positive plate of one joined to the negative plate
of the other. The potential difference across each will be
(1) 3 V (2) Zero (3) 6 V (4) 4 V

Q 76. Two spherical conductors A and B of radii R and 2R respectively are each given a charge Q.
When they are connected by a metallic wire. The charge will-
(1) flow from A to B
(2) flow from B to A
(3) remain stationary on conductor
(4) none of these

Q 77. If potential difference across a capacitor is changed from 15 V to 30 V work done is W. The
work done when potential difference is changed from 30 V to 60 V, will be :
(1) W (2) 4 W (3) 3 W (4) 2 W

Q 78. Two condensers of capacities 2C and C are joined in parallel and charged upto potential V.
The battery is removed and the condenser of capacity C is filled completely with a medium
of dielectric constant K . The p.d. across the capacitors will now be -
3𝑉 3𝑉 𝑉 𝑉
(1) (2) (3) (4)
𝐾+2 𝐾 𝐾+2 𝐾

Q 79. Two capacitor each having a capacitance C and breakdown voltage V are joined in series.
The effective capacitance and maximum working voltage of the combination is :-
𝐶 𝑉 𝐶
(1) 2C, 2V (2) 2 , 2 (3) 2C, V (4) 2, 2V

Q 80. A 40 F capacitor in a defibrillator is charged to 3000 V. The energy stored in the capacitor is
sent through the patient during a pulse of duration 2 ms. The power delivered to the patient
is :
(1) 45 kW (2) 90 kW (3) 180 kW (4) 360 kW

Q 81. 0.2F capacitor is charged to 600V by a battery. On removing the battery. It is connected
with another parallel plate condenser (1.0F). The potential decreases to-
(1) 100 volts (2) 120 volts (3) 300 volts (4) 600 volts

Baluni Classes, 30, Bhagya Nagar, Between ISBT & Amar Ujala Press, Bye Pass Road, Agra. Ph. 9837919228.
13
Q 82. Two capacitors with capacity C1 and C2, when connected in series, have a capacitance Cs and
when connected in parallel have a capacitance Cp. Which of the following is true ?
𝐶1 𝐶2 𝐶𝑠 𝐶1
(1) Cs = C1 + C2 (2) Cp = (3) = (4) CsCp = C1C2
𝐶1 +𝐶2 𝐶𝑝 𝐶2

Q 83. A parallel plate capacitor C has a charge q and potential V between the plates. Work
required to double the distance between the plates is :
1 1 1 𝑉 2
(1) 2CV2 (2) 4CV2 (3) 2 𝐶 ( 2 ) (4) CV2

Q 84. For circuit, the equivalent capacitance between P and Q is

P Q
C C C C C C
(1) 6C (2) 4C (3) 3C/2 (4) 3C/4

Q 85. Two metallic spheres of radii R1 and R2 are connected by a thin wire. If + q1 and + q2 are the
charges on the two spheres then :
𝑞1 𝑅12 𝑞1 𝑅1 𝑞1 𝑅13 𝑞1 (𝑅12 −𝑅22 )
(1) = (2) = (3) = (4) =
𝑞2 𝑅22 𝑞2 𝑅2 𝑞2 𝑅23 𝑞2 (𝑅12 +𝑅22 )

Baluni Classes, 30, Bhagya Nagar, Between ISBT & Amar Ujala Press, Bye Pass Road, Agra. Ph. 9837919228. 14
 Answer Key

Q.1) 1 Q.2) 1 Q.3) 4 Q.4) 1 Q.5) 3

Q.6) 3 Q.7) 2 Q.8) 3 Q.9) 4 Q.10) 3
Q.11) 4 Q.12) 2 Q.13) 2 Q.14) 4 Q.15) 4
Q.16) 2 Q.17) 2 Q.18) 1 Q.19) 2 Q.20) 2
Q.21) 4 Q.22) 3 Q.23) 2 Q.24) 4 Q.25) 3
Q.26) 3 Q.27) 4 Q.28) 3 Q.29) 3 Q.30) 1
Q.31) 1 Q.32) 2 Q.33) 3 Q.34) 4 Q.35) 4
Q.36) 3 Q.37) 3 Q.38) 2 Q.39) 3 Q.40) 4
Q.41) 1 Q.42) 1 Q.43) 3 Q.44) 1 Q.45) 2
Q.46) 2 Q.47) 2 Q.48) 3 Q.49) 1 Q.50) 2
Q.51) 4 Q.52) 3 Q.53) 3 Q.54) 2 Q.55) 3
Q.56) 1 Q.57) 2 Q.58) 2 Q.59) 1 Q.60) 1
Q.61) 1 Q.62) 1 Q.63) 2 Q.64) 3 Q.65) 2
Q.66) 3 Q.67) 1 Q.68) 1 Q.69) 2 Q.70) 4
Q.71) 4 Q.72) 1 Q.73) 1 Q.74) 3 Q.75) 4
Q.76) 1 Q.77) 2 Q.78) 1 Q.79) 4 Q.80) 2
Q.81) 1 Q.82) 4 Q.83) 1 Q.84) 4 Q.85) 2

Baluni Classes, 30, Bhagya Nagar, Between ISBT & Amar Ujala Press, Bye Pass Road, Agra. Ph. 9837919228. 15