CM - 006

Modular Communication
Kit
Overview
The modular Communication Kit is based on the concept of Block Diagram. It is a featured solution
for introducing communication technologies to the trainee for the first time. The kit consists of multiple
blocks, each block represents a part of the circuit that performs an experiment. It’s Covering a wide
range of topics in Analog and Digital Communications. using Kit modules, trainees can perform up to
36 diverse experiments. The modules are easy to connect together by using of 2mm safety bananas.

Specifications
• Module Left hand side banana is for signal • Input and outputs are protected due to
inputs ( high impedance inputs ). mis-wiring.
• Module Right hand side banana is for • Variable controls adjustment in modules
signal outputs ( Low impedance outputs ). depends on observation and measurement
• Banana Marks for analog and digital of output signals.
signals to ease the interconnection.

BEDO ® reserves the right to change materials or modify the design of its product without notification as part of
the company’s continuing product improvement program
www.bedoeg.com 1
Electronics & Communications
• Kit modules: • Input Signal : Analog ( Audio Range )
» Variable DC Voltage Signal Module: • Cutoff Freq : 2.6 KHz
• Output Signal : Variable (-2.5 to 2.5V up » Line Code Encoder Module:
to 5mA), Fixed (+5V DC up to 10mA) • Input Signal : Digital 0:5V
» Function Generator Module: • Line Codes Modes :
• Output Signal: » Non Return to Zero level (NRZ-L).
» Analog ( 100KHz Sine, 2KHz Sine, 100KHz » Bi-phase line (Manchester).
Cos ) 4Vpp » Return to Zero - Alternate Mark Invert
» Digital ( 100KHz, 8KHz, 2KHz ) 0:5V (RZ-AMI)
» Variable DC Voltage Signal Module: » Non Return to Zero - Mark (NZR-M)

• Output Signal : Variable (-2.5 to 2.5V up • Input Clock : Digital 0:5V, up to 100 KHz
to 5mA), Fixed (+5V DC up to 10mA) • Output Signal : -2V to +2V
» Noise Generator Module: » PCM Encoder Module:
• Output Signal : 3 Analog outputs • Input signal : 2 Analog +/- 2Vp ( Audio
0dB (4.8Vrms) , -6dB (2.4Vrms) , -20dB Frequency ), CLK Digital 0:5V up to 128KHz
(0.48Vrms) • Output Signal : Serial, 0:5V Data Stream in
• BW : 10Hz to 240KHz, White Noise Standard offset binary format (8bits) Plus
Frame Synchronization Pulse (FS).
» Sequence Generator Module:
• Modes : PCM / TDM
• Input Signal : Digital 0:5V ,1Hz to 100KHz
» PCM Decoder Module:
• Number of sequences : 2, X (31 bits)
• Input Signal : Serial, 0:5V Data Stream in
and Y (255 bits)
Standard offset binary format (8bits) Plus
• Output Signals : Digital 0:5V ( X, Y and Frame Synchronization Pulse (FS) and CLK
Sync ) Digital 0:5V up to 128KHz.
» Twin Pulse Generator Module: • Output signal : 2 Analog +/- 2Vp ( Audio
• Input Signal : Digital 0:5V ,up to 8KHz Frequency )
• Output Signals : 2 Digital 0:5V ( Q1, Q2 ) • Modes : PCM / TDM
• Control : Pulse Width (5 to 40 µs), Pulse » Phase Shifter Module:
Delay (Q2-Q1 50 to 300µs) • Input signal : Analog up to 4Vpp
» Voltage Controlled Oscillator Module: • BW: DC to 200 KHz
• Input Signal: digital -3:3V , analog 4Vpp • Control : Phase shift adjustment
• Two operating frequency ranges: Low potentiometer (0:360 Degree)
1KHz to 17KHz, High 60KHz to 140Khz » Adder Module:
• Output signal : analog and digital (1KHz • Input signal : Analog up to 4Vpp
to 17KHz , 60KHz to 140Khz) • BW: DC to 600 KHz
• Gain: 1 to 2 • Gain : 0 to 2
» Comparator Module: » Buffer Module:
• Input Signal : Analog 4Vpp and DC • Input signal : Analog up to 4Vpp
Threshold • BW: DC to 600 KHz
• Output Signals : Digital 0:5V ( Up to 100 • Gain : 0.2 to 10
KHz ) » Band Pass Filter Module :
» Rectifier Module: • Input signal : Analog up to 4Vpp
• Input Signal : Analog 4Vpp (Up to • Center Freq : 100 KHz
100KHz) • BW: 20 KHz
• Output Signals : Analog Half wave • Gain : 1
rectified • Type : 6 th order chebyshev with 0.1dB
» Diode and RC Low pass filter Module: ripple

www.bedoeg.com BEDO ® reserves the right to change materials or modify the design of its product without notification as part of
2 the company’s continuing product improvement program
Electronics & Communications
» Low Pass Filter Module : • Output Signal : Analog and 3.5mm
• Input signal : Analog up to 4Vpp Stereo socket for headphone > 80 ohm
• Cutoff Freq : 2 KHz impedance

• Gain : 0.9, Type : 4 th order Butterworth • Output power : 0.125 W

» Tunable Low Pass Filter Module : • Control : Gain adjustment potentiometer

• Input signal : Analog up to 4Vpp » Multiplier Module:

• Input Signals: 2 Analog Signals AC
• Cutoff Freq : 0.6 KHz to 12 KHz
Coupled, 2 DC offsets
• Gain : 0 to 1.6, Type : 8 th order Elliptic
• BW : DC to 600KHz
» Divider Module :
• Output Signal : 1 Analog Signal
• Input signal : Digital 0:5V
» Serial To Parallel Module:
• Output signal : Digital 0:5V
• Input Signal : 2 Digital 0:5V ( Serial
• Input Frequency : up to 1MHz
Data, CLK up to 100KHz )
• Modes : Invert, Divide by 2/4/8
• Output Signal : 2 Digital -2:2V ( X1, X2 )
» Dual Analog Switch With Sample And Hold
» Speech Module:
Module:
• Input Sensor : Electret-Type
• Input Signal : 2 of Analog inputs up to
Microphone
4Vpp
• Output Signal : Analog 0.6Vrms
• BW : DC To 50 KHz
» Expansion module:
• Control Signals : 2 of Digital 0:5V ( Up to
• To install optional additional modules
100 KHz )
» Analog I/O module:
• Output Signal : 1 Analog Output, 1 S&H
output • 4 terminals to produce signals or read
and analyze analog signals using the
» EXOR Module:
software
• Input Signal : 2 of Digital inputs 0:5V
» Digital I/O module:
• BW : DC to 1MHz
• 8 terminals to produce digital signals or
• Output signal : Digital 0:5V
read and analyze digital signals using
» Headphone Amplifier Module: the software
• Input Signal : Analog

Experiments
• Amplitude modulation (AM) and • Sampling & reconstruction
demodulation • (PCM) encoding / Decoding
• Product detection of (AM) signals • (PCM) and time division multiplexing (TDM)
• Noise in (AM) communications • An introduction to Armstrong’s modulator
• Double Sideband (DSBSC) modulation • Bandwidth limiting and restoring digital
• Observations of (AM) and (DSB-SC) signals signals
in the frequency domain • Amplitude Shift Keying (ASK)
• Single Sideband (SSB-SC) modulation & • Frequency Shift Keying (FSK)
demodulation • Binary Phase Shift Keying (BPSK)
• Single Sideband (SSB) modulation & • Quadrature Phase Shift Keying (QPSK)
demodulation
• Spread Spectrum - (DSSS) modulation &
• Frequency Modulation (FM) and demodulation
Demodulation
• Undersampling in Software Defined Radio
• (FM) Generation using the harmonic
• Phase division modulation and
multiplier method
demodulation

www.bedoeg.com
3
BEDO ® reserves the right to change materials or modify the design of its product without notification as part of
the company’s continuing product improvement program
Electronics & Communications
• Pulse-width modulation (PWM) and • Principles of Gaussian FSK (GFSK)
demodulation • PN sequence spectra and noise
• Message translation and inversion generation
• Carrier acquisition using the phase-locked • Line coding and bit-clock regeneration
loop • Delta modulation and demodulation
• Signal-to-noise ratio and eye diagrams • Delta-sigma modulation and
• Pulse code modulation (PCM) and signal- demodulation
to-noise distortion ratio (SNDR) • Method 2 of AM and product detection of
• (ASK) demodulation using product AM signals
detection • FM Generation using the harmonic
• (FSK) generation with switching method multiplier method
and demodulation

Scope of Delivery Options

• Modular Communication Kit (CM - 005) • Digital content (BI-01)
• Hard copy user manual

Required for Operation

• Computer Interface Base Unit with Built-in
Power Supply (MS-001)

www.bedoeg.com BEDO ® reserves the right to change materials or modify the design of its product without notification as part of
4 the company’s continuing product improvement program