Scribd
Upload
33 views

PHECDA-Firmware Upgrade Guide

Uploaded by

scolle
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
33 views

PHECDA-Firmware Upgrade Guide

Uploaded by

scolle
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 5

Phecda Laser Engraver & Cutter Firmware Upgrade Guide

-Windows

Precautions
1. To update the firmware, the engraving machine needs to be turned on,
otherwise MKSLaserTool cannot detect the port.
2. When updating the touchscreen firmware, you need to prepare a USB Type-C
data cable.
3. Please close other software when updating the firmware to avoid the port being
occupied and MKSLaserTool cannot detect the port.
4. You can close the MKSLaserTool software only after it shows that the
touchscreen update is successful.
5. After the update is completed, restart the engraving machine.
6. It takes about one minute to update the firmware of the touch screen, and about
two minutes to update the mainboard firmware.

File Description The file name contains ESP32_TFT is the


touchscreen firmware. Use MKSLaserTool
software to update, open MKSLaserTool,
change FLASH SIZE to 4MB, and then click Start
to update. Please refer to the following for
detailed operation steps.

The file name contains DLC32_V4.0 is the


motherboard firmware. Use the MKSLaserTool
software to update, open the MKSLaserTool,
change the FLASH SIZE to 8MB, and then click
Start to update. Please refer to the following for
detailed steps.

This is the software needed to update the


firmware. If it fails to operate normally, please
right-click the software to run it as an
administrator.

1
ELEGOO Support： [email protected]
2
ELEGOO Support： [email protected]
Update Touchscreen Firmware

1. Connect the touchscreen motherboard and computer with a USB Type-C data
cable, and turn on the power supply of the machine.

2. Run MKSLaserTool (if you cannot operate after opening, please close the software,
then right-click the software to run as an administrator), enter the first option MKS
ESP32 Download Tool, change the FLASH SIZE to 4MB, select the touchscreen
firmware to start updating, reconnect the engraving machine and computer after
updating.

The first step is to select the


touchscreen firmware
The third step is
Phecda_ESP32_TFT_xxxxxxxxxx.bin
to click Start to
update the
firmware. After The second step is to change the
the update is FLASH SIZE to 4MB
completed,
restart the
engraving
machine and it
can be used
normally.
Indicates that the firmware is
updated successfully

3
ELEGOO Support： [email protected]
Update Motherboard Firmware

1. Connect the engraving machine to the computer with the blue square port data
cable, and turn on the power supply of the machine.

2. Run MKSLaserTool (if it cannot be operated after opening, please close the
software, then right-click the software to run as an administrator), enter the first
option MKS ESP32 Download Tool, change the FLASH SIZE to 8MB, select the
motherboard firmware to start updating. After the update finishing, reconnect the
engraving machine to the computer.

The first step is to select the


motherboard firmware
The third step Phecda_DLC32_V4.0_xxxxxxxxxx.bin
is to click
Start to
update the The second step is to change the
firmware. FLASH SIZE to 8MB
After the
update is
completed,
restart the
engraving
machine and
it can be used Indicates that the firmware is
normally. updated successfully

4
ELEGOO Support： [email protected]
FAQ

1. Garbled code error occurs during the update?


If the data cable is not connected properly, check the connection of the data cable or
reconnect it again.

2. Can't read SD card and can't control engraving machine after the update is
complete?
When updating the motherboard firmware, the touchscreen firmware is used, just
re-update the correct motherboard firmware again.

3. The touchscreen does not light up after the update is complete?


When updating the touchscreen firmware, the motherboard firmware is used, just
re-update the correct touchscreen firmware.

4. Unable to read the port when using MKSLaserTool to update the firmware?
If the port is occupied by other software, please close other software; or if the data
cable is not connected correctly, please check the connection of the data cable or
reconnect it again.

5. Report an error when starting the update?


If the FLASH SIZE is selected incorrectly, the touchscreen firmware should be changed
to 4MB, and the motherboard firmware should be changed to 8MB. After changing
to the correct FLASH SIZE, re-update the firmware again.

5
ELEGOO Support： [email protected]

You might also like