Philips AVS

DVDR3355 Firmware Upgrade

Firmware Upgrade

We have developed a firmware upgrade to improve your product.

This upgrade is applicable for the following models:
DVDR3355/37

This firmware version improves: Click here for more details

User interface improvement

Note: Before you proceed to upgrade, please be reminded that you need to do configuration again
each time after firmware upgrade!

Upgrade Procedure

Step 1 Check your current version

First check your current firmware version to see if you need to upgrade:
1. Keep no disc in DVD tray.
2. Press <0>, <0>, <0>, <9>, <OK> on the Remote Control.
3. The software version is "DVDR33XX_XX_BTX_X, 43.0X.XX" displayed on the TV screen.
4. Compare the version shown on screen with this firmware upgrade version, BT6_4, 43.02.19/43.03.10.
If the current software is lower than BT6_4, proceed to step 2.
If the loader version shown on the screen is 43.02.XX and XX is lower than 19, proceed to step 2.
If the loader version shown on the screen is 43.03.XX and XX is lower than 10, proceed to step 2.
Otherwise, no upgrade is necessary.

Step 2 Download Firmware upgrade

Click the link to save the software on your computer.

Step 3 Burning Upgrade on CD-R / CD-RW

1. Extract the files by unzipping the zipped file – DVDR33xx_xx_BTx_x.zip

(Do not rename the filenames) Tip: For more
2. Write the extracted files – not the zip file – onto a blank CD-R or CD-RW disc, information on burning
using the following settings: software we refer to
- File System: ISO 9660 + Joliet two popular burning
- File name length : max11 chars = 8+3 (Level 1) software programs
- Mode : 2/XA
- Character set : ISO 9660 (ISO norme CD-ROM) www.nero.com
- No multi session www.easycdcreator.com
- Write Speed : Low
3. Finalize the disc. (The application may do this automatically.)
4. If you need to upgrade the loader software, select the file PHILIPS_D43.bin if your drive version is
43.02.XX or the file PHILIPS_D43C.bin if your driver version is 43.03.XX
5. Write the selected file onto another blank CD-R or CD-RW disc, using the same settings as above.
6. Finalize the disc. (The application may do this automatically.)

Downloaded from www.Manualslib.com manuals search engine

 Philips AVS

Step 4 Apply Upgrade to your Set

1. Power up the set and open the DVD tray.

2. Insert the prepared upgrade CD-ROM.
3. Close the tray and the set will auto read the disc.
4. Upon recognize the disc, the local display of the recorder will show "SW UPGD". The TV screen will
show a dialog box titled “Disc Upgrade”
5. Note: The set will indicate “Unknown Disc” in the following 2 situations.
- When the software upgrade is not meant for your set (Check the applicable models above)
- Problem with writing of CD-ROM. Try again with a different CD-ROM if possible.
6. Navigate to OK button on TV and press <OK> on the remote control. You can cancel the upgrade at this
point by navigating to CANCEL button on TV and pressing <OK> on the remote control.
7. If you proceed with the upgrade, the local display of the recorder will scroll the message “ SW
UPGRADING”, while a progress bar will be shown on the TV screen.
8. The whole process takes about 1 minute after which, the local display of the recorder shows “SW DONE”
and the dialog box on TV screen indicates successful upgrading. The tray will open as well.
9. Remove the CD-ROM before pressing <OK> on the remote control. The set should close the tray and
restart automatically after about 10 seconds.
10. Note: Do not press any buttons or interrupt the mains supply during the entire upgrading process,
otherwise the set may become defective..
11. Note: Sometimes, the set does not close the tray. Do not be alarmed. Simply press <STANDBY> on the
remote control to wake up the set and the tray will close immediately.
12. It is better to power off and on the set again after software upgrade before using the set.

Proceed to Step 5 if loader software upgrade is needed.

Step 5 Apply Loader Software Upgrade to your Set

1. Power up the set and open the DVD tray.

2. Insert the prepared loader software upgrade CD-ROM.
3. Close the tray and the set will auto read the disc.
4. Upon recognizing the disc, the local display of the recorder will show "DRV UPG". The TV screen will
show a dialog box titled “Loader Software Upgrade”
5. Note: The set will indicate “Unknown Disc” in the following 2 situations.
- When the software upgrade is not meant for your set (Check the applicable models above)
- Problem with writing of CD-ROM. Try again with a different CD-ROM if possible.
6. Navigate to OK button on TV and press <OK> on the remote control. You can cancel the upgrade at this
point by navigating to CANCEL button on TV and pressing <OK> on the remote control.
7. If you proceed with the upgrade, the local display of the recorder will scroll the message “ DRIVE
UPGRADING”, while a progress bar will be shown on the TV screen.
8. The whole process takes about 4 minute after which, the local display of the recorder shows “DRV
DONE” and the dialog box on TV screen indicates successful upgrading. The tray will open as well.
9. Remove the CD-ROM before pressing <OK> on the remote control. The set should close the tray and
restart automatically after about 10 seconds.
10. Note: Do not press any buttons or interrupt the mains supply during the entire upgrading process,
otherwise the set may become defective..
11. Note: Sometimes, the set does not close the tray. Do not be alarmed. Simply press <STANDBY> on the
remote control to wake up the set and the tray will close immediately.
12. It is better to power off and on the set again after software upgrade before using the set.

Your product is successfully upgraded!

Firmware upgrade history

Firmware Version BT6_4
Release Date Mar 3 2006
This upgrade software improves the following performance:
• MPEG audio decode improvement.
• Solved time display problem.

Downloaded from www.Manualslib.com manuals search engine