Scribd
Upload
1 views

Screening Test

Uploaded by

Daniel Getachew
Copyright
© © All Rights Reserved
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
1 views

Screening Test

Uploaded by

Daniel Getachew
Copyright
© © All Rights Reserved
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 4

Electrical Materials

1. Describe the analogy of conduction through solid dielectric material with respect to external
applied voltage

2. Briefly explain about magnetostriction.


3. What is Curie point? Why is it important for magnetic materials?
4. What is anisotropy? Explain the advantages of grain oriented hard ferrite.
5. What is polarization? Explain the polarization in polar and non polar materials.
6. Define dielectric loss? Explain clearly with suitable equation.
7. What is Hall Effect ? How semiconductor is useful to measure magnetic field?

8. Compare Germanium rectifier and Silicon rectifier.

9. Explain the term breakdown voltage of a dielectric. Specify the factors which affect the dielectric
strength.
10. Calculate the electric field required to make a Force of 2.4 x 10-16 N on an electron.
Applied Electronics I & II

1. In an npn transistor in CB configuration, only 2 percent of electrons injected into the base
recombine with the majority carrier holes in the base. If 106 electrons leave from emitter per µs,
how many electrons come out of (a) the base lead and (b) collector lead per µs.
2. For a half wave rectifier, if Vm = 12 V , diode forward resistance is 10 Ω and load resistance is 1.2
K Ω, then find peak, average and rms value of load current.
3. Draw the energy band diagram for an n-type semiconductor.
4. What is potential barrier? How is it formed in unbiased p-n junction?
5. What is meant by the collector reverse saturation current ICO ?

6. What is clipper? Draw a clipper circuit which has to pass output between 2 V and 4 V of given
input sinusoidal signal.

7. For a BJT working in CE configuration, the collector current is 14 mA and base current is 50 µA.
Determine the current gains α and β.

8. Describe electronic shell and forbidden energy gap.


9. Define the term ionization energy of an atom.
10. In a pnp transistor operating in active region in CB configuration, the emitter current I E is 14 mA
and α = 0.995 . Compute the collector current IC and the base current IB . Neglect ICO .
11. Explain the term bipolar as used in bipolar transistor.
12. What are the merits and demerits of FETs over BJTs?
13. What is the need for biasing of an amplifier?

14. Differentiate an oscillator with an amplifier.

15. In a RC phase shift oscillator, if R = 10 KΩ , C = 1000 pF for getting 4 KHz frequency of oscillation,
what will be the value of Rc ?

16. Differentiate positive and negative feedback.


17. What is the change in input and output impedance with feedback for an amplifier?
18. Evaluate the gain of OP AMP, when input is given to non-inverting terminal.
19. Mention the properties of an instrumentation amplifier.
20. What is meant by piezo electric effect? How is used for oscillation?
DSP

1. Using basic building block, sketch the block diagram representation of the
discrete-time system described by the given I/O relation.

y(n) = 1/3 [y(n-1)] - 3[y(n-2)] + x(n) + 2 x2(n-1)

2. What is the Nyquist rate for the given analog signal ?


xa (t) = 3 cos 2000 πt + 5 sin 6000 πt – cos 12000 πt.

3. Compute the z transform of the signal given below.


5
x(n) = ∑ (-1)k δ(n-k)
k=0

4. Determine the signal x(n) which z transform is given by


X(z) = log ( 1 – a z-1) ; |z| > a

5. Evaluate the z transform of the signal


x(n) = u(n) – 2n u(-n-1)

6. Compute one sided z transform of the following signal


x(n) = 3 δ(n +2) – δ(n +1) + δ(n) – 2 δ(n –1) + 7 δ(n –3).

7. Evaluate z transform of the sequence shown in the figure below.


x(n)

2
1
n
1 2 3 4 5 6

8. Find unit imple response for a linear phase FIR filter in window design method of order N = 64 to
approximate following ideal frequency response magnitude.
Ha(jω) = 1 ; | ω | < = 0.3π
= 0 ; 0.3π < = | ω | < = π

9. An analog signal varying from +8V to -7.5V is quantized. If the number of quantization level is 32,
what is the range of quantization error voltage?

10. The linear convolution of x(n) and w(n) is


z(n) = x(n) * w (n) = [ 1, 1, 1, 1, 1, 3, 3, 2, 2, 2, 2, 2 ]
then determine 8 point circular convolution of the two function x(n) and w(n).
Signals & System Analysis

1. Draw the wave form for the signal which equation given below
f(x) = -(x2 +1) for x < 0 and
f(x) = x2 +1 for x > 0

2. Find Fourier Transform of the function


f(t) = e-2t u(t)
3. Draw the signal of the given function f(t) = 2r(t) – 4 u(t-1) – 2 r(t-2) .

4. Find the output of a differentiator if unit step function is given as input. Also draw i/p and o/p
wave forms.

5. Evaluate Laplace transform of the given function.


x(n)
2

1
n
1 2 3 4 5 6

You might also like