Scribd
Upload
13 views6 pages

001-020 Crankshaft Gear, Rear (Crankshaft Installed)

Uploaded by

Hussain Ahmed
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
13 views6 pages

001-020 Crankshaft Gear, Rear (Crankshaft Installed)

Uploaded by

Hussain Ahmed
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

25/03/2024, 10:18 QuickServe Online | (4388731) QSG12 CM2880 G112 Service Manual

(/qs3/pubsys2/xml/en/manual/4388731/4388731-titlepage.html)

Trainings

Exploded View

Rear Crankshaft Gear (Crankshaft Installed) Exploded View


1. Friction shim - quantity 1
2. Crankshaft gear - quantity 1
3. Capscrew - quantity 1

Select Service Tools


Recommended Cummins® Service Tools

https://quickserve.cummins.com/qs3/portal/service/manual/en/4388731/ 1/6
25/03/2024, 10:18 QuickServe Online | (4388731) QSG12 CM2880 G112 Service Manual

Guide pins, Part Number 3376638


Additional Service Items
No additional service items required.

General Information
 CAUTION 
Do not reuse or stack friction shims or engine damage
may occur.

 CAUTION 
Friction shim, flywheel, and crank gear interconnecting
surfaces must be free of grease upon installation or
engine damage may occur.

The rear crankshaft gear is bolted on to the last main journal of


the crank. The crankshaft gear shall not be removed unless it
is being replaced.

This engine uses friction enhancing shims between the crank


and gear and between the gear and flywheel. This design is
unique in that the rear crank gear is a separate piece bolted on
to the last main journal of the crank, rather than being a press
fit gear in more conventional designs.

The crankshaft and crankshaft gear shall not be separated


unless the crankshaft gear is being replaced. If they are
separated insure that a new shim is replaced in the joint.

Preparatory Steps
 WARNING 

https://quickserve.cummins.com/qs3/portal/service/manual/en/4388731/ 2/6
25/03/2024, 10:18 QuickServe Online | (4388731) QSG12 CM2880 G112 Service Manual

Batteries can emit explosive gases. To reduce the possibility of personal injury, always
ventilate the compartment before servicing the batteries. To reduce the possibility of
arcing, remove the negative (-) battery cable first and attach the negative (-) battery cable
last.

Note : This procedure is intended to be performed in-chassis with the alternator


removed. However, some applications can require the engine to be removed if space
is limited or the engine can not be adequately supported.
Disconnect the batteries. See equipment manufacturer service information.
Rotate the engine to insert the crankshaft and camshaft timing pins. Refer to Procedure 001-
088 in Section 1. (/qs3/pubsys2/xml/en/procedures/417/417-001-088.html)
Disconnect the alternator. See equipment manufacturer service information.
Remove the lubricating oil pan. Refer to Procedure 007-025 in Section 7.
(/qs3/pubsys2/xml/en/procedures/417/417-007-025.html)
Remove the starting motor. Refer to Procedure 013-020 in Section 13.
(/qs3/pubsys2/xml/en/procedures/417/417-013-020.html)
Remove the flywheel. Refer to Procedure 016-005 in Section 16.
(/qs3/pubsys2/xml/en/procedures/417/417-016-005.html)
Remove the rear crankshaft seal. Refer to Procedure 001-024 in Section 1.
(/qs3/pubsys2/xml/en/procedures/417/417-001-024.html)
Use a jackstand or a suitable lifting fixture to support the rear of the engine.
Remove the flywheel housing. Refer to Procedure 016-006 in Section 16.
(/qs3/pubsys2/xml/en/procedures/417/417-016-006.html)

Remove
Install guide pins, Part Number 3376638, in two of the flywheel
mounting locations to support the crankshaft gear.

Remove the crankshaft gear retaining capscrew.

Remove the crankshaft gear and discard friction shim.

https://quickserve.cummins.com/qs3/portal/service/manual/en/4388731/ 3/6
25/03/2024, 10:18 QuickServe Online | (4388731) QSG12 CM2880 G112 Service Manual

Clean and Inspect for Reuse


 WARNING 
When using solvents, acids, or alkaline materials for
cleaning, follow the manufacturer's recommendations for
use. Wear goggles and protective clothing to reduce the
possibility of personal injury.

 WARNING 

Wear appropriate eye and face protection when using


compressed air. Flying debris and dirt can cause personal
injury.

Clean the crankshaft nose with cleaning pad, Part Number


3823258 or equivalent. Debris remaining on the crankshaft can
prevent the correct installation of the gear.

Inspect the machined surface for scratches or nicks.

Use a crocus cloth to remove any scratches or nicks.

If scratches or nicks can be felt with a fingernail after the


crankshaft has been polished with the crocus cloth, the
crankshaft must be replaced.

Install
 CAUTION 
Do not reuse or stack friction shims or engine damage
may occur.

 CAUTION 

Friction shim, flywheel, and crank gear interconnecting


surfaces must be free of grease upon installation or
engine damage may occur.

https://quickserve.cummins.com/qs3/portal/service/manual/en/4388731/ 4/6
25/03/2024, 10:18 QuickServe Online | (4388731) QSG12 CM2880 G112 Service Manual

Slide the new friction shim and the crankshaft gear over the
guide pins, Part Number 3376638.

Align dowel pin.

Install the crankshaft gear retaining capscrew through the gear


and the shim and into the crankshaft.

Tighten the capscrew.

Torque Value: 281 n•m [ 207 ft-lb ]

Finishing Steps
 WARNING 

Batteries can emit explosive gases. To reduce the possibility of personal injury, always
ventilate the compartment before servicing the batteries. To reduce the possibility of
arcing, remove the negative (-) battery cable first and attach the negative (-) battery cable
last.

Set the base engine timing. Refer to Procedure 001-088 in Section 1.


(/qs3/pubsys2/xml/en/procedures/417/417-001-088.html)
Install the flywheel housing. Refer to Procedure 016-006 in Section 16.
(/qs3/pubsys2/xml/en/procedures/417/417-016-006.html)
Install the rear crankshaft seal. Refer to Procedure 001-024 in Section 1.
(/qs3/pubsys2/xml/en/procedures/417/417-001-024.html)
Install the flywheel. Refer to Procedure 016-005 in Section 16.
(/qs3/pubsys2/xml/en/procedures/417/417-016-005.html)
Install the starting motor. Refer to Procedure 013-020 in Section 13.
(/qs3/pubsys2/xml/en/procedures/417/417-013-020.html)
Install the lubricating oil pan. Refer to Procedure 007-025 in Section 7.
(/qs3/pubsys2/xml/en/procedures/417/417-007-025.html)
Install the alternator. See equipment manufacturer service information.
Remove the crankshaft and camshaft timing pins. Refer to Procedure 001-088 in Section 1.
(/qs3/pubsys2/xml/en/procedures/417/417-001-088.html)
Connect the batteries. See equipment manufacturer service information.
Operate the engine and check for proper operation.

https://quickserve.cummins.com/qs3/portal/service/manual/en/4388731/ 5/6
25/03/2024, 10:18 QuickServe Online | (4388731) QSG12 CM2880 G112 Service Manual

Last Modified: 07-Mar-2017

https://quickserve.cummins.com/qs3/portal/service/manual/en/4388731/ 6/6

You might also like