CBCS SCHENME

18ENG25
USN

Second Semester B.Arch. Degree Examination, July/August 2022

Building Structures- I|
Max. Marks: 100
Time: 3 hrs.
malpractice.
Note: Answer any FIVE full questions,choosing ONE fullquestion from each module.
as Module-1
trcatcd (10 Marks)
1 a. With neat sketch draw and explain the stress strain curve for mild steel. destruction.
200mm is tested to
pagcs.
blank
remaining
be b. A specimen of steel 25mm diameter with a gauge length of load at elastic limit is 160kN.
the
wilIl It has an extension of 0.16mm under a load of 80kN and 56mm and diameter at neck
50, The maximum load is 18OkN. The total extension at fracture is
= is 18mm. Find:
+8 Stress at elastic limit
42
eg, ii)) Young's modulus
thewritten iii) Bending stress
on iv) % reduction in area (10 Marks)
V) Ultimate tensile stress.
lines
equations
cross OR
or
diagonal 2 a. Explain the following :
and i) Normal stress
ii) Shear stress
drawcvaluator ii) Bending stress (10 Marks)
compulsorily iv) Thermal stress.
of 40kN, the total
to b. A bar shown in Fig.Q2(b) is tested in UTM. It is observed that at a load
appeal extension of the bar is 0.285mm. Determine the Young's modulus of the material.

identification, 40KN
answers,
A,: 25mm
your
of
completing
revealing Fig.Q2(b) (10 Marks)

Module-2
OnAny Define shear force and bending moment with sign convention. (06 Marks)
3 a
bending moment diagram for
1. 2. b. Compute the reactions and draw shear force diagram and
:Note
simply supported beam shown in Fig.Q3(b).
Important

Fig.Q3(b) (14 Marks)

Iof3
 18ENG25

OR
4 a. Draw SFD and BMD for a cantilever beam subject to UDL of W KN/m for the whole
length í. (06 Marks)
b. Calculate shear force and bending moment and draw SFD and BMD for Fig.Q4(b).
5KN 20Kw

A
2m
Fig.Q4(b) (14 Marks)

Module-3
5 a. State the assumptions made in theory of simple bending. (06 Marks)
b. Acast iron bracket, subjected to bending has a cross section of I-shape with unequal flanges
as shown in Fig.Q5(b). If the section is subjected to a shear force of 1600kN, draw the shear
stress distribution over the depth of section.

200m

200m

Fig.Q5(b) (14 Marks)

OR
6 Write the expression for sectional modulus for the following:
i) Rectangular section
ii) Hollow rectangular
iii) Circular
iv) Hollow circular section. (08 Marks)
b. A simply supported beam of span 10m is 350mm deep. The section of the beam is
symmetrical. The moment of inertia of the section is 9.5 x 10'mm. If the permissible
bending stress is 120N/mm.
Find:
i) the safe point load that can be applied at the centre ofthe span
ii) the safe uniformly distributed load that can be applied on the span
Neglect the dead load of the beam. (12Marks)

Module-4
a. Write the difference between short column and long column. (05 Marks)
b. Determine the buckling load for a strut of T-section, flange width being 100mm, overall
depth 80mm and both flange and stem are 1Omm thick. The strut is 3m long and is hinged at
both ends.Take E = 200N/mm. (1S Marks)

2 of 3
 BQ
-
of3 3
BQ
**
-
BQ
Fig.Q10
Marks) (20
D
JokN
1000cm". |= and N/mm 10° x 2=TakeE
deflection Maximum i)
'Deflection
C' at i)
Determine:
shown the at
asends supported simply span
is beam
8m of AB A 10
Fig.Q10. in
OR
Fig.Q9(b)
Marks) (14
B(
m.15 *25
J000N
Fig.Q9(b)). (Refer N/mm. 10000 deflection
=TakeE end. free at the find deep, 240mm
section
is the If end. free the 1000Nat load point anda
of end
and wide 120mmrectangular of A
fixed the from 1.25m length
of 2500N/m
afor ofUDL carriesa length cantilever
2m
theory. dilution assumptions
made
in thExplain
e a. 9
Marks) (06
Module-5
12
Marks) (14
Fig.Q8(b)
To 350mm
25Dmby
=3. FOS
10°N/mm, =2
x Take
E fixed. ends both with strut aasused which
is Qmlength
of
havingaFig.Q8(b), shown
in column
as I-section oad
anfor lcrippling Euler's Determine b.
Marks) (06 load.buckling length, effective ratio,
slendeness Define a. 8
OR
3 7 a m
18ENG25