Scribd
Upload
5 views

Concrete_Primer_(1)[1]

Uploaded by

mithu.tv.bd
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
5 views

Concrete_Primer_(1)[1]

Uploaded by

mithu.tv.bd
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

CONCRETE PRIMER

ASTM D 41 PRIMER
Bituminous Roofing Primer
DESCRIPTION DRYING TIME

BITUMAT CONCRETE PRIMER is a cold 4 hours to touch.


applied general purpose roofing primer
formulated with highly pliable, flexible bitumen, COVERAGE RATE
select petroleum solvents and compounded with
wetting and saturation additives. 0.3 - 0.5 ltr/m2 depending on Condition of Substrate

USES PACKING

BITUMAT CONCRETE PRIMER is suitable for 18.2 ltr. Pails and 200 ltr. Drums
concrete, smooth asphalt roofs, brick and metal
surfaces, used as the prime coat prior to HEALTH AND SAFETY
installation of any BITUMAT membranes.
Flammable; contains petroleum distillate. Keep
OUTSTANDING FEATURES away from open fire, sparks or other ignition
sources, wear protective clothing, gloves and
Select solvent allows for optimum goggles during application.
penetration of BITUMAT CONCRETE
PRIMER into the surface pores, pin holes 1 Fire - Flammable when wet, flash point
and cracks. 40°C.

Absorbs the existing dust and scale thus 2 Skin - Avoid repeated or prolonged
prevents the formation of additional dust contact. However, if it occurs, remove with
and scale. hand cleaner that removes oil or grease,
then clean with soap and water.
The resulting surface permits the proper
bonding of self adhesive as well as 3 Eyes - Contact could cause irritation. If
torchable membranes, in addition to any contact occurs, flush immediately with
other bituminous adhesives and coatings. clean water.

APPLICATION 4 Inhalation - Can cause dizziness. Move


to fresh air. If dizzy and breathing
The surface must be thoroughly cleaned, and difficulty persists, administer oxygen
all dust, dirt, loose coatings, oil or greasy and contact physician.
substances removed, concrete must be
completely cured, and dried prior to priming. CLEANING
BITUMAT CONCRETE PRIMER should be
allowed to dry before application of subsequent Tools : Clean with kerosene.
layers. Hands : Use a hand cleanser or
kerosene followed by soap
It can be applied with a roofing brush, roller, and water.
squeegee, or airless spray equipment at the
recommended coverage rate.
CONCRETE PRIMER - ASTM D 41 PRIMER
Bituminous Roofing Primer

TECHNICAL DATA

Property Typical Value Test Method

1 Density at 25°C, kg/litre 0.87-0.90 ASTM D 70

2 Viscosity, at 25°C cps 70-160 Brookfield

3 Drying time to touch, hr. 4 -

4 Drying time through, hr. 24 -

5 Flash point, T.O.C.,°C 40 min. ASTM 3143

6 Non-volatile, % wt 45 min. ASTM D 402

7 Volatile, % wt 55 max. ASTM D 402

8 Penetration of asphalt from distillation 20-50 ASTM D 5

9 Water content Nil ASTM D 95


0.3 - 0.5/ltr/M2
10 Coverage rate Depending upon
condition of substrate

Note : Bitumat Concrete Primer is not affected by chemicals present in the soil such as salt, asphalts, etc.

The information given in this Technical Data Sheet reflects typical median properties based on laboratory test, and practical experience; subject to the tolerance levels
of UEAtc directives. However, as the product is often used under conditions beyond our control, we can’t warrant but the product itself.

THIS PUBLICATION AUTOMATICALLY SUPERSEDES ALL PREVIOUS PUBLICATIONS RELATING TO THIS PRODUCT.

MSD 01/2002

You might also like