Scribd
Upload
39 views2 pages

TDS_J24FS040

Uploaded by

mahendrasolake03
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
39 views2 pages

TDS_J24FS040

Uploaded by

mahendrasolake03
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

J24FS040 LOW DENSITY POLYETHYLENE

GENERAL PURPOSE FILM GRADE


J24FA040

These are blown film grades and can be extruded with considerable ease. J24FS040 has been
blended with necessary additives during manufacture to obtain good surface slip and easy open-
ability between two layers of the film.

Additive Details:
J24FS040: ● Slip: Yes ● Anblock: Yes
J24FA040: ● Slip: No ● Anblock: No

TYPICAL CHARACTERISTICS*

PROPERTY TEST METHOD UNIT TYPICAL VALUE**


Density (23˚C) ASTM D 792 g/cc 0.923
Melt Flow Index (190˚C / 2.16 Kg) ASTM D 1238 g/10 min 4.0
Tensile Strength at Break (MD/TD) ASTM D 882 MPa 18/16
Elongation at Break (MD/TD) ASTM D 882 % 250/400
Dart Impact Strength (F50) ASTM D 1709/A g/µ 2.0
Haze ASTM D 1003 % 7
Gloss (60°) ASTM D 2457 - >100
* Typical characteristics and not to be taken as specifications
** Typical properties measured on 40 µm film made with 0.8 mm die gap & 2.5 BUR.

APPLICATIONS:
High slip grade for shopping bag, zip lock bags, general purpose consumer packaging. Non-slip grade can be
used for bubble wrap and lamination film.

Reliance Industries Limited, Product Application & Research Centre (PARC), Vadodara Manufacturing Division, P. O. Petrochemicals, Village Koyali,
District Vadodara: Pin 391346, Gujrat, India.
E-mail: [email protected] Website: www.ril.com

Updated as of April 2019


Typical Process Conditions:

• Melt Temperature (˚C): 160 – 200


• Recommended Blow Up Ratio (BUR): 1.5 – 3.0 (Based on applications, best results achieved with BUR of
2.5: 1)
• Die Gap: > 0.8 mm (Based on film thickness and throughput of the machine)

Regulatory Information

• Meets the requirements stipulated in standard IS: I0146 on "Specification for Polyethylene for safe use in contact with
foodstuffs, pharmaceuticals, and drinking water". It also conforms to IS 16738:2018 “Positive List of Constituents for
Polypropylene, Polyethylene and their Copolymers for its Safe Use in Contact with Foodstuffs and Pharmaceuticals”
• The grade and the additives incorporated in it also comply with the FDA: CFR Title 21,177.1520, Olefin polymers.

Storage Recommendations

• Bags should be stored in dry/closed conditions at temperatures below 50°C and protected from UV / direct sunlight.

DISCLAIMER

The information contained herein may include typical properties and processing parameters of the grade or its
typical performances when used in respective applications. The values given above are based on analysis of
representative samples and not the actual product supplied. It is the customer’s responsibility to inspect and test
our grades in order to satisfy itself as to the suitability of the products for customers’ particular application. The
customer is solely responsible for all determinations regarding any use of material or product and any process in
its area of interest. RIL assumes no obligation or liability for any loss, damage or injury directly or indirectly
suffered or incurred as a result of using any of the information or product given in this document. The
information and data presented herein is true and accurate to the best of our knowledge. No warranty or
guarantee expressed or implied, is made regarding performance or otherwise. This information and data may
not be considered as a suggestion to use our products without taking into account existing patents, or legal
provisions or regulations, whether national or international. The user of any information and/or data is advised
to obtain the latest details from any of the offices of the company or its authorized agents, as the information
and/or data is subject to change based on the research and development work undertaken by the company.

Reliance Industries Limited, Product Application & Research Centre (PARC), Vadodara Manufacturing Division, P. O. Petrochemicals, Village Koyali,
District Vadodara: Pin 391346, Gujrat, India.
E-mail: [email protected] Website: www.ril.com

Updated as of April 2019

You might also like