USER MANUAL

FULL BODY HARNESS

ANSI / ASSE Z359.11 - 2014
ASTM F0887-20

(+52 ) 81.8122.2600
[email protected]
www.goldeneagle.com.mx

Autopista al Aeropuerto No. 104 - CP 66647

Fracc. Bosques de San Miguel II sector
Apodaca, Nuevo Leon, Mexico

Autopista al Aeropuerto #104 Fracc. Bosques de San Miguel II sector, Apodaca, Nuevo Leon, Mexico
Telephone:(+52 ) 81.8122.2600 Email: [email protected] Web: www.goldeneagle.com.mx
Instruction manual Product label
The manufacturer’s instructions shall be provided to the users. Do not skip this instruction manual. Read the instruction manual
carefully before using the equipment. If failed ill doing so it may cause serious injury or death.

This manual must be read and understood in its entirety and used as part of fall protection training program as required by
OSHA or any state regularity agency. These instructions are intended to meet the manufacturer instructions as required by
ANSI/ASSE Z359.11-2014. The user must fully understand the proper equipment use and limitations.

The shelf life of the product depends on a regular inspection program.

First use date: ________________________________________________________________
at least every 12 months. Initials of the name of the competent person conducting the inspection.
The user must inspect the equipment before EACH use. A competent person must conduct a formal inspection

20____
20____
20____
20____

YEAR JAN FEB MAR APR MAY JUN JUL AUG SEP OCT NOV DIC
100 MM
FULL BODY HARNESS-TYPE XXX
STANDARD: ANSI/ASSE Z359.11-2014 &
MANUFACTURING DATE: XXXXXX
ASTM F0887-20
MODEL: XXXXXX

INSPECTION TABLE
The instructions applies to the following models REFERENCE: XXX
SIZE: XX
CAPACITY: 130-310 lb (59-140 kg) max.
weight included tools.

>> 4 Point X Harness. MATERIAL: Kevlar Nomex webbing and WARNING:

dielectric hardware. Consult the manufacturer's instructions
>> 4 Point H Harness. CAPACITY:130-310 lb (59-140 kg) max. weight before using the product. Training is
recommended for use care and maintenance.
>> 4 Point X Harness. included tools (59-140 kgs.).
SERIAL NUMBER : XXXXXX
Not following the recommendations can
cause serious injury or death.
>> 4 Point H Harness. LOT NUMBER : XXXXXX
Avoid sharp edges and abrasive surfaces.
>> 5 Point Dielectric H-Harnes.
Back Front
Inspect the equipment before each use.
Use front "D" ring for prevention lifeline.
>> 8 Point Dielectric H-Harnes with belt. limited to maximum 2 feet or 60 cm away.
Remove from service if undergoing a

>> 6 Point Confined Space Harness. fall arrest.

A). Fall arrest. The harness webbing have a minimum

>> Construction Harness. B). Controlled ascent-descent. breaking strength of 7000 lbf (31.14kN).
C). Positioning.

DO NOT REMOVE THIS LABEL DO NOT REMOVE THIS LABEL DO NOT REMOVE THIS LABEL

MANUFACTURED BY: SOLUCIONES DE ALTURA S.A DE C.V MANUFACTURED BY: SOLUCIONES DE ALTURA S.A DE C.V MANUFACTURED BY: SOLUCIONES DE ALTURA S.A DE C.V
Autopista de Aeropuerto #104 Col. Bosques de San Miguel II 66647 Autopista de Aeropuerto #104 Col. Bosques de San Miguel II 66647 Autopista de Aeropuerto #104 Col. Bosques de San Miguel II 66647
Apodaca N.L Mexico. Apodaca N.L Mexico. Apodaca N.L Mexico.

40 MM
General requirements, warnings and limitations
The equipment is designed for use as a part of a personal fall protection system. Components must not be used for any other
operation other than that which it has been designed and approved. Fall Arrest System is designed to comply with OSHA. Fall
Restraint System must be designed by a qualified person, and must be installed and used under the supervision of a
competent person. Registration, inspectation, maintenance
• All authorized persons/users must refer the regulations governing occupational safety, as well as applicable ANSI or CSA
standards. Please refer to product labeling for information on specific OSHA regulations, and ANSI and CSA standards met by
SERIAL NUMBER:
product.
MODEL:

• Consult a doctor if there is any reason to doubt a user’s ability to withstand and safely absorb fall arrest forces. Age, fitness, PURCHASE DATE: FIRST USE:
health conditions can seriously affect the worker a fall occur. Pregnant women and minors should not use this equipment. INSPECTION DATE:
INSPECTION CORRECTIVE MAINTENANCE
OBSERVATIONS: MEASURES: PERFORMED:
• Proper precautions should always be taken to remove any obstructions, debris, material, or other recognized hazards from the Approved by:
work area that could cause injuries or interfere with the operation of the system. All equipment must be inspected before each
use according to the manufacturer’s instructions. All equipment should be inspected by a qualified person on a regular basis. Approved by:

• To minimize the potential for accidental disengagement, a competent person must ensure system compatibility.
Approved by:

• Equipment must not be altered in any way. Repairs must be performed only by the manufacturer, or persons or entities
authorized in writing by the manufacturer. Approved by:

• Any product exhibiting deformities, unusual wear, or deterioration must be immediately discarded. Any equipment subject to a Approved by:
fall must be removed from service. The authorized person/user shall have a rescue plan and the means at hand to implement it
when using this equipment.
Approved by:
• Never use fall protection equipment for purposes other than those for which it was designed. Fall protection equipment should
never be used for towing or hoisting. Approved by:

• All synthetic material must be protected from slag, hot sparks, open flames, or other heat sources. The use of heat resistant Approved by:
materials is recommended in these applications.

• Never use natural materials (manila, cotton, etc.) as part of a fall protection system. Approved by:

. Do not Altering the equipment. Approved by:

. Follow the instructions, do not misusing equipment.

2 11
System requirements • Do not expose this equipment to chemicals which may have a harmful effect on the materials used to construct it. Be especially
aware of caustic environment, or those that contain high levels of organic acids or bases. If you are uncertain about the safe
operation of this equipment in any environment, contact Golden Eagle for further instructions.
• Compatibility of Components: Golden Eagle Fall Protection equipment is designed to be used with Golden Eagle approved
components. Please contact Golden Eagle if you have a question regarding compatibility. Making substitutions without approval • Do not use the equipment near sharp edges and abrasive surfaces.
from Golden Eagle Fall Protection may lead to injuries and or death by compromising the safety and reliability of the complete
system. A qualified person can make a determination on compatibility of equipment from different manufacturers. • Do not use the equipment around moving machinery or electrical hazards and exposure to light (UV degradation).

. Do not exposing the equipment to chemicals, heat, flames or other environmental conditions, which may produce a harmful
• Compatibility of Connectors: Connectors (D-rings, hooks, carabiners) must be capable of supporting at least 5,000 lbs. (22kN). effect and to consult the manufacturer in case of doubt.
Do not use equipment that is not compatible. Non-compatible connectors may unintentionally disengage. Self-locking snap
hooks and carabiners are required by CSA, ANSI and OSHA. Connectors must be compatible in size, shape, and strength. . Golden Eagle Full Body Harness should be used only with the combinations of components, sub-systems or both which may
affect or interfere with the safe function of one another. Be certain that connecting devices are compatible and that other
elements of the PFASare safe to use and compatible before use. Contact Golden Eagle for further instructions.
• Making Connections: Only use self-locking snap hooks and carabiners with any Golden Eagle Fall Protection Equipment. Do not
use equipment that is not compatible.
System limitations & requirements

Consider the following limitations/requirements prior to installing or using this equipment:

Others Capacity: Golden Eagle Full Body Harnesses are designed for use by persons with a combined weight (clothing, tools, etc.) of no
more than 340 lbs. (140 kg.) Make sure all of the components in your system are rated to a capacity appropriate to your
application.

Maintenance & Cleaning: Free Fall: Personal fall arrest systems used with this equipment must be rigged to limit the free fall to 6 feet (1.8 M) per ANSI
Repairs to equipment can be made only by a Golden Eagle representative or person or entity authorized by Golden Eagle. Z359. Restraint systems must be rigged so that no vertical free fall is possible. Work positioning systems must be rigged so that
Contact Golden Eagle for maintenance and repair. Cleaning after use is important for maintaining the safety and life of the free fall is limited to 2 feet (.6 m) or less. Personnel riding systems must be rigged so that no vertical free fall is possible. Climbing
equipment. Cleanse the equipment of all dirt, corrosives, and contaminants. If the equipment cannot simply be wiped clean use systems must be rigged so that free fall is limited to 18 in. (.46 cm) or less. Rescue systems must be rigged so that no vertical
a mild soap and water. Rinse, wipe, and hang to dry in shade. free fall is possible. See subsystem manufacturer’s instructions for more information. Below figure illustrates fall clearance
requirements. There must be sufficient clearance below the user to allow the system to arrest a fall before the user strikes the
ground or other obstruction. Clearance required is dependent on the following factors. There must be sufficient clearance below
Storage: the user to allow the system to arrest a fall before the user strikes the ground or other obstruction.
Store the harness in a cool, dry and clean place out of direct sunlight. Avoid areas where heat, moisture, light, oil, and chemicals
or their vapors or other degrading elements may be present. Equipment which is damaged or in need of maintenance should
not be stored in the same area as usable equipment. Heavily soiled, wet, or otherwise contaminated equipment should be Clearance required is dependent on the following factors: A
properly maintained (e.g. dried and cleaned) prior to storage. Prior to using equipment which has been stored for long periods
of time, a formal inspection should be performed by a competent person. For harnesses with Dielectric Buckles, pass-thru - Elevation of Anchorage.
buckles or Quick Connect Buckles, store the harness with the buckles connected.
A. Connected subsystem. D
- Connecting Subsystem Length. B. Working level. B F
C. Low level of obstruction. E
Training: - Deceleration Distance. D. 6 ft (1.8m) free fall (ANSI Z339.1).
It is the responsibility of the users to assure that they read, understand, and follow all instructions and are trained in the care
E. Deceleration distance.
and use of this device. Training should be repeated periodically and any time there is a change of components within the - Free Fall Distance.
F. Free fall (d) + deceleration (E).
system. Training must be conducted without exposing the trainee to a fall hazard.
- Worker Height.
C

- Movement of Harness Attachment Element.

Swing Falls: Swing falls occur when the anchorage point is not directly above the point where a fall occurs. The force of striking
an objectin a swing fall may cause serious injury or death. Minimize swing falls by working as close to the anchorage point as
possible. Do not permit a swing fall if injury could occur. Swing falls will significantly increase the clearance required when a
self-retracting lifeline or other variable length connecting sub system is used.

Environmental Hazards: Use of this equipment in areas with environmental hazards may require additional precautions to
preventinjury to the user or damage to the equipment. Hazards may include, but are not limited to heat, chemicals, corrosive
environments, high voltage power lines, gases, moving machinery, and sharp edges.

Compatibility of Components: Unless otherwise noted, Golden Eagle equipment is designed for use with Golden Eagle
approved components and subsystems only. Substitutions or replacements made with non-approved components or
subsystems may jeopardize compatibility of equipment and may affect safety and reliability of the complete system.

10 3
Compatibility of Conectors: Connectors are considered to be compatible with connecting elements when they have been Propper harness fit
designed to work together in such a way that their sizes and shapes do not cause their gate mechanisms to inadvertently open
regardless of how they become oriented. If the connecting element that a snap book or carabiner attaches to is undersized or
irregular in shape, a situation could occur where the connecting element applies a force to the gate of the snap hook or It is extremely important that your harness fits and is properly adjusted. Failure to do so can result in serious injury or death,
carabiner. This force may cause the gate (of either a self-locking or a non-locking snap hook) to open, allowing the snap hook or and proper connection of both types of straps is essential to fall safety. After donning a harness, make sure to check:
carabiner to disengage from the connecting point. Connectors must be compatible in size, shape, and strength. Self-locking
snap hooks and carabiners are required by ANSI and OSHA. Chest Strap: Should be positioned in the middle of your chest [6” (152mm) to 8” (203mm) below the trachea but not below the
sternum]. If the chest strap is positioned too high, the strap may move upwards during a fall arrest causing you to run the risk
Making Connections: Always use snap hooks and carabiners which needs double manual action to open with this equipment. of strangulation. If the chest strap is too low or not connected at all, you could fall out of your harness during a fall.
Only use connectors that are suitable to each application. Ensure all connections are compatible in size, shape and strength. Do
not use equipment that is not compatible. Ensure all connectors are fully closed and locked. Leg Straps: Proper adjustment of the leg straps is critical for safety. Leg straps should be snug, but not snug to the point that
they obstruct normal blood circulation in the legs. Failure to wear leg straps will not secure your body within the harness during
The connection should not be made: a fall and could lead to serious injury or death.

A. To a D-ring to which another connector is attached. Sub-pelvic Strap: Provides support in the event of a fall, and also provides support when used for positioning. In a seated
position, the sub pelvic strap should comfortably provide a “seat” for the buttocks. In the event of a fall, simply lift up your legs
B. In a manner that would result in a load on the gate. to transfer weight to the sub-pelvic strap.

C. In a false engagement, where features that protrude from the snap hook or carabiner catch on the anchor and without visual
confirmationseems to be fully engaged to the anchor point.
Fall clearance
D. To each other.
3.6 m of free fall Anchor point
If there is a risk of fall or if the only anchorage is
E. Directly to webbing or rope lanyard or tie-back (unless the manufacturer’s instructions for both the Lanyard and connector
below the attachment points on the harness, it is
specifically allow such a connection). 6 Ft. Length of energy-absorbing lanyard
essential to use a lanyard provided with an energy
Total 20 Ft. Before
absorber. Before using a shock-absorbing lanyard, 5 Ft. Decelaration Distance
F. To any object which is shaped or dimensioned such that the snap hook or carabiner will not close and lock, or that roll-out from
check that there is sufficient fall clearance below anchorage After 6 Ft. Height of Worker
could occur.
the user to prevent any collision with the structure
3 Ft . Safety Factor
or the ground. With a weight of 220 lbs and a fall
Note: Other than 3,600 lb. (16 kN) gated hooks, large throat opening snap hooks should not be connected to standard size
factor of two (the least favorable case), the fall
O-rings or similar objects which will result in a load on the gate if the hook or D-ring twists or rotates. Large throat snap hooks
clearance D is the stopping distance H (2L+5.74 ft)
are designed for use on fixed structural elements such as rebar or cross members that are not shaped in a way that can
plus an additional distance of 3.28 ftp.
capture the gate of the hook.

Restrictions regarding making connections: Periodic examination

• Do not make connections where the hook locking mechanism can Keep these instructions with the product and fill in the identification sheet, entering the information taken from the
come into contact with a structural member or other equipment and markings. The periodic examination is essential to test the resistance and condition of the equipment and to guarantee
potentially release the hook. the safety of the user.A qualified person must examine this equipment at least once each year in strict compliance with
the instructions of the manufacturer and the previous check must be recorded on the attached sheet.
• Do not connect a snap hook into a loop or thimble of a wire rope or Inappropriate Connections
attach in any way to a slack wire rope. The frequency of inspection should be increased in accordance with the regulations, if the equipment is in heavy usage
A. B. C. D. or if the equipment is used in harsh environments. Check also that the markings are legible.
• The snap hook must be free to align with the applied load as
intended (regardless of the size or shape of the mating connector).
Material & construction
• A carabiner may be used to connect to a single or pair of soft
loops on a body support such as a body belt or full body harness, E. F. G. H. Webbing Materials:
provided the carabiner can fully close and lock. This type of • Made up of high tenacity polyester; breaking strength 5000 lbs. tensile strength.
connection is not allowed for snap hooks.
Pad and Label Cover Materials:
• A carabiner may be connected to a loop or ring connector that is • All outer fabric is Nomex and Kevlar blend fabric.
already occupied by an automatic closing connector. • Fire Resistant Hook and Loop Fasteners.
• Blend of nylon and polyester.

4 9
Steps 1: Webbing/Stitches If the connecting element that a snap hook (shown) or carabiner attaches to is undersized or irregular in shape, a situation
Grasp the webbing with your hands 6 inches (152mm) to 8 inches (203mm) apart. Bend the webbing in an inverted “U” as could occur where the connecting element applies a force to the gate of the snap hook or carabiner. This force may cause the
shown. The surface tension resulting makes damaged fibers or cuts easier to detect. Follow this procedure the entire length of gate (of either a self-locking or non-locking snap hook) to open, allowing the snap hook or carabiner to disengage from the
the webbing, inspecting both sides of each strap. Watch for frayed edges, broken fibers, pulled stitches, cuts, burns, and conecting point.
chemical damage.
Connecting Sub-Systems: Connecting subsystems (self-retracting lifeline, lanyard, rope grab and lifeline, cable sleeve) must be
Steps 2: D-Rings/Pads suitable for your application. See subsystem manufacturer’s instructions for more information. Some harness models have web
Check D-rings for distortion, cracks, breaks, and rough or sharp edges. The D-ring should pivot freely. Inspect for any unusual loop connection points. Do not use snap hooks to connect to web loops. Use a self-locking carabiner to connect to a web loop.
wear, frayed or cut fibers, or broken stitching of the D-ring attachments. Pads should also be inspected for cracks, excessive Ensure the carabiner cannot cross-gate load (load against the gate rather than along the backbone of the carabiner). Some
wear, or other signs of damage. lanyards are designed to choke onto a web loop to provide a compatible connection. See Figure 8. Lanyards may be sewn
directly to the web loop forming a permanent connection. Do not make multiple connections onto one web loop, unless choking
Steps 3: Buckles two lanyards onto a properly sized web loop.
Inspect for any unusual wear, frayed or cut fibers, or broken stitching of the buckle attachments.

Steps 4: Tongue Buckles/Grommets

Buckle tongues should be free of distortion in shape and motion. They should overlap the buckle frame and move freely back 1. Insert Lanyard Web Loop (A) through Web Loop 1
and forth in their socket. Roller should turn freely on frame. Check for distortion or sharp edges. Inspect for loose, distorted or or D-ring onharness (B). A
B
broken grommets. Webbing should not have additional punched holes.
2. Insert opposite end of lanyard through the 2
Steps 5: Friction and Slotted Mating Buckles Lanyard Web Loop.
Inspect the buckle for distortion. The outer bars and center bars must be straight. Pay special attention to corners and
attachment points at the center bar. 3. Pull the Lanyard through the connecting Web
Loop to secure.
3
Steps 6: Quick-Connect Buckles
Inspect the buckle for distortion. The outer bars and center bars must be straight. Make sure dual-tab release mechanism is
free of debris and engages properly.

Rescue Plan: Rescue operation must be performed by the trained and competent personal. The rescue operation must be
Donning the harness performed under the supervision of the rescue expert team or personal. It is advised that while working on site work in pairs.
Before going for the work the user must have the rescue plan according to the work.
Full-body harnesses are the only form of body wear
tobe used for fall protection/fall arrest. It is very If Equipment is Subjected to a Fall: Remove the equipment from service immediately if it has been subjected to the forces of a
importantto have a proper fitting harness throughout fall arrest. Contact your distributor or Golden Eagle about policies regarding replacement of Golden Eagle components involved
the entirecourse of a work shift. Do not allow your in a fall.
harness tobecome loose or slack. The following
procedure willdescribe how to properly “don” (put on) a Specific Instructions: Golden Eagle anchors are designed to provide complete attachment system to user in the event of a fall.
Step 1 y 2 Step 3 Step 4 Step 5 Step 6
harness. Thelocation of the chest, leg and sub-pelvic These attachment systems must be connected to the proper body support and connecting facility. These anchors are meant to
straps are criticalto the optimal performance of a hold the victim off all till the rescue operation is performed, so this is important that the whole system must have the all the
full-body harness ina fall arrest. essential components before going for the use. The whole fall arrest system must be used by the trained/competent person. It
is advisable to make a checklist of the essential components according to one’s use before going for work.

Step-1: Hold harness by back D-ring. Shake harness to allow all straps to fall in place. Use of Fall Arrest: The fall arrest system MUST ONLY be connected to the back attaching element on the harness provided for
the purpose (“D” ring or webbing attachment extension) or to the chest anchorage points (“webbing link” or “D” link). The chest
Step-2: If chest, waist and/or leg straps are buckled, release straps and unbuckle at this time. anchorage points must imperatively be used together. The D-rings on the belt and the ventral anchorage point must only be
used for the attachment of a work positioning or retaining system and never with a fall arrest system. During use, check
Step-3: Slip straps over shoulders so D-ring is located in middle of back between shoulder blades. regularly the adjustment and/or attachment points.

Step-4: Pull leg strap between legs and connect to opposite end. Repeat with second leg strap. Connect waist strap, if Product Labeling:
present.Waist strap should be tight but not binding.
1. Shoulder strap 10. Back Plaque.
Step-5: Connect chest strap and position in mid chest area 6” (152mm) to 8” (203mm) below the trachea but not below the 11. Sub-Pelvic Strap.
2. Chest strap
sternum.Tighten to keep shoulder straps taut.
3. Torso Adjustment. 12. Inspection/ID Label.
Step-6: After all straps have been buckled, tighten all webbing so that harness fits snug but allows full range of movement.-
4. Parachute/Tongue Bubkle/Quick-Connect Fastener. 13. Warning/Instruction Label.
Pass excess strap through loop keepers.
5. Sternal D-ring 14. Standard labels
Step-7: To remove harness, reverse procedure.
6. Ventral D-ring
7. Side D-rings
8. Thight Strap
9. Dorsal D-ring.

8 5
 1
B. Work Positioning: The structure to which the work positioning system is attached must sustain static loads applied in the
1
directions permitted by the work positioning system of at least 3,000 lbs., or twice the potential impact load, whichever is
2 9 2
greater (See OSHA). When more than one work positioning system is attached to an anchorage, the strengths stated above
9
3 9 must be multiplied by the number of work positioning systems attached to the anchorage.
4 10 10
2 4 10
6
5
12 13 14 C. Restraint: Anchorages selected for restraint and travel restraint systems shall have strength capable of sustaining static
3 5
3
12 13 14 loads applied in the directions permitted by the system of at least: 1. 1,000lbs. (4.5kN) for non-certified anchorages, or 2. Two
4 times the foreseeable force for certified anchorages. When more than one restraint and travel restraint system is attached to
7 7 3
an anchorage, the strengths set forth in (I) and (2) above shall be multiplied by the number of systems attached to the
11 12 7 7
anchorage.
13
4 8
14

8
8 11 11 D. Rescue: Anchorages selected for restraint and travel restraint systems shall have strength capable of sustaining static loads
8
applied inthe directions permitted by the system of at least: 1.3,000 Ibs. (13.3kN) for non-certified anchorages, or 2. Five times
the foreseeable force for certified anchorages. When more than one restraint and travel restraint system is attached to an
anchorage, the strengths set forth in (I) and (2) above shall be multiplied by the number of systems attached to the anchorage.
Full body harness applications
Table 2 - Anchor Strength Requirements
Application Class Description
The full body harness is used as a component of a personal fall arrest system. Personal fall arrest Fall Arrest Non-certified Anchorage 5,000lbs (22.2 kN)
systems typicallyinclude a full body harness and a connecting subsystem (energy absorbing lanyard). Certified anchorage 2 times the maximum arresting force for certified anchorage
Personal Fall Arrest Class A Maximum arresting force must not exceed 1,800 lbs(8 kN). For fall arrest applications connect the fall
arrest subsystem (example: lanyard, SRL, energy absorber, etc.) to the D-ring or attachment element on Restrain Non-certified Anchorage 1.000 lbs (4,5kN)
your back, between your shoulder blades.
Certified anchorage 2 times the foreseeable force for certified anchorages
For controlled descent applications, harnesses equipped with a single sternal level D-ring, one or two
Controlled descent Class D frontal mounted D-rings, or a pair of connectors originating below the waist (such as a seat sling) may Work positioning Non-certified Anchorage 3.000 lbs (13,3kN)
be used for connection to a descender or evacuation system (reference in Z259.10 in Canada).
Certified anchorage 2 times the foreseeable force for certified anchorage
The full body harness is used as a component of a rescue system. Rescue systems are configured
depending on the type of rescue. For limited access (confined space) applications, harnesses equipped Rescue Non-certified Anchorage 3.000 lbs (13,3kN)
Rescue Class E
with D-rings on the shoulders may be used for entry and egress into confined spaces where worker Certified anchorage 5 times the foreseeable force for certified anchorage
profile is an issue.
The full body harness is used as a component of a climbing system to prevent the user from falling when The structure which a climbing system is attached must sustain the loads required by that particular system.
Climbing
climbing a ladder or other climbing structure. Climbing systems typically include a full body harness, See the instructions for the climbing system for requirements.
Ladder Climbing Class L
vertical cable or rail attached to the structure, and climbing sleeve. For ladder climbing applications,
1 Multiple Systems: When more than one of the defined system is attached to an anchorage, the strength denfied for Non Certified or certified
harnesses equipped with a frontal D-ring in the sternal location may be used for fall arrest on fixed
anchorage shall bemultiplied by the number of systems attached to the anchorage.
ladder climbing systems. These are defined in ANSI A14.3 in the United States.
The full body harness is used as a component of a work positioning system to support the user at a work 2 Certified Anchorage: An anchorage for fall arrest, positioning, restraint, or rescue systems that a qualified person certifies to be capable of
position. Work positioning systems typically include a full body harness, positioning lanyard, and a supporting the potentialfall force that meet the criteria for a certified anchorage prescribed in this standard.
Work Positioning Class P back-up personal fall arrest system. For work positioning applications, connect the work positioning
subsystem (example: lanyard, Y-lanyard, etc.) to the lower (hip level) side or belt mounted work
positioning attachment anchorage elements (D-rings). Never use these connection points for fall arrest.
Description of product
The full body harness is used as a component of a restraint system to prevent the user from reaching a
Restrain None fall hazard. Restraint systems typically include a full body harness and a lanyard or restraint line.
Golden Eagle Harnesses are designed and tested to comply with applicable OSHA and ANSI standards for fall protection
equipment. When used as a component in a personal fall arrest system, or a personal restraint system, the Golden Eagle
Anchorage Strength: Anchorage and anchorage strength requirements are dependent on the full body harness application (see Harnesses provide workers with the full body harness system designed to allow the body to help absorb the impacts of a fall
below figure). In accordance with ANSI Z359.1, anchorage selected for fall Arrest Systems must meet the anchorage strength should one occur.
requirementsdefined in Table 2.
INSPECTION: Before each use, proceed with thorough visual examination to ensure that the PPE is intact (the same applies for
the equipment used with the harness (connectors, lanyard) and take all necessary steps concerning the implementation of
A) Fall Arrest: Anchorages selected for fall arrest systems shall have strength capable of sustaining static loads applied in the
rescue in total safety. In the event of your product being contaminated, consult the manufacturer or authorized agent. If you
directions permitted by the system of at least: 1.5,000lbs. (22.2 kN) for noncertified anchorages, or 2. Two times the maximum
have any doubts regarding the safe state of the product or if the product has been used to arrest a fall, for your personal
arresting force for certified anchorages. When more than one fall arrest system is attached to an anchorage, the strengths set
safety, it is essential to withdraw the PPE from service and send it back to the manufacturer or a qualified repair center for
forth in (I) and (2) above shall be multiplied by the number of systems attached to the anchorage.
checking or destruction. Following the inspection, the center will provide written authorization or refusal for the use of the PPE.
As per OSHA: Anchorages used for attachment of personal fall arrest systems shall be independent of any anchorage being
Before each use of this equipement, inspect it according to the following guidelines: A formal inspection of fall protection
used to support or suspend platforms and capable of supporting at least 5,000 lbs. (22.2kN) per user attached, or be designed,
products/components must be performed at least every six months by a competent person other than the user. The frequency
installed and used as part of a complete PFAS which maintains a safety factor of at least two, and is under the supervision of
of formal inspections should be based on conditions of use or exposure. Record the inspection results in the inspection and
a qualified person.
maintenance log at the end of this manual.

Remove equipment from service if it has been subjected to the forces of arresting a fall and will include information on
inspection of load indicators.

6 7