Scribd
Upload
3 views

Mini Project-Report-guidelines

Vtu mini project report guidelines

Uploaded by

ra23ece
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
3 views

Mini Project-Report-guidelines

Vtu mini project report guidelines

Uploaded by

ra23ece
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

GUIDELINES FOR THE PREPARATION OF B.E./B. Tech.

MINI
PROJECT REPORTS
1. Mini Project reports should be typed neatly only on one side of the paper with 1.5 or double line
spacing on aA4 size bond paper (210 x 297 mm). The margins should be: Left - 1.25", Right - 1", Top
and Bottom - 0.75".

2. The total number of reports to be prepared is three.

 One copy to the department


 One copy to the concerned guide(s),if they want
 One copy to the candidate, if they want

3. Before taking the final printout, the approval of the concerned guide(s) is mandatory and suggested
corrections, if any, must be incorporated.
4. Every copy of the report must contain

 Inner title page (White)


 Outer title page with a plastic cover
 Certificate in the format enclosed from the college.
 An abstract (synopsis) not exceeding 100 words, indicating salient features of the work.

5.The organization of the report should be as follows


1. Inner title page
2. Certificate
3. Acknowledgments
Usually numbered in roman
4. Abstract
5. Table of Contents
6. List of table & figures (optional)

 Chapters(to be numbered in Arabic) containing Introduction-, which usually specifies the scope
of work and its importance and relation to previous work and the present developments, Main
body of the report divided appropriately into chapters, sections and subsections.
 The chapters, sections and sub sections may be numbered in the decimal form for e.g. Chapter 2,
sections as 2.1, 2.2 etc., and subsections as 2.2.3, 2.5.1 etc.
 The chapter must be left or right justified (font size 16). Followed by the title of chapter centered
(font size 18), section/subsection numbers along with their headings must be left justified with
section number and its heading in font size 16 and subsection and its heading in font size 14. The
body or the text of the report should have font size 12.
 The figures and tables must be numbered chapter wise for e.g.: Fig. 2.1 Block diagram of a serial
binary adder, Table 3.1 Primitive flow table, etc.
 The last chapter should contain Conclusions and the Future Enhancement in the relevant field.

7. Reference OR Bibliography: The references should be numbered serially in the order of their
occurrence in the text and their numbers should be indicated within square brackets for e.g. [3]. The
section on references should list them in serial order in the following format.

1. For textbooks - A.V. Oppenheim and R.W. Schafer, Digital Signal Processing, Englewood, N.J.,
Prentice Hall, 3 Edition, 1975.
2. For papers - Devid, Insulation design to combat pollution problem, Proc of IEEE, PAS, Vol 71,
Aug 1981, pp 1901-1907.

 Only SI units are to be used in the report. Important equations must be numbered in decimal
form for e.g.
 V = IZ .......... (3.2)
 All equation numbers should be right justified.
 The Seminar report should be brief and include descriptions of work carried out by others only to
the minimum extent necessary. Short excerpts from published work are desired to be included;
they should be within quotation marks appropriately referenced.
 Proper attention is to be paid not only to the technical contents but also to the organization of the
report and clarity of the expression. Due care should be taken to avoid spelling and typing
errors. The student should note that report-write-up forms the important component in the overall
evaluation of the Technical Seminar.
 The reports submitted to the department/guide(s) must use spiral binding. (Note: Outer covering
sheets must be of purple colour.)

You might also like