SECTION 10 28 00

TOILET, BATH, AND LAUNDRY ACCESSORIES

1.1 DESCRIPTION
A. This section specifies manufactured items usually used in dressing rooms, toilets, baths, locker
rooms and at sinks in related spaces.
B. Items Specified:
1. Paper towel dispenser.
2. Combination paper towel dispenser and disposal unit.
3. Waste receptacles.
4. Toilet tissue dispenser.
5. Grab Bars
6. Shower curtain rods
7. Clothes hooks, robe or coat.
8. Towel bars.
9. Metal framed mirror
10. Medicine cabinet.
11. Foot operated soap dispenser.
12. Soap dishes.
13. Paper cup dispenser.
14. Mop racks.
B. This section also specifies custom fabricated items used in toilets and related spaces.
1.2 RELATED WORK
A. Color of finishes: Section 09 06 00, SCHEDULE FOR FINISHES
B. Ceramic toilet and bath accessories: Section 09 30 13, CERAMIC TILING
C. Custom fabricated accessories: Section 10 28 00, TOILET, BATH AND LAUNDRY
ACCESSORIES.
D. Shower curtain break away pendant chain hooks: Section 10 21 23, CUBICLES.
E. Color of vinyl fabric: Section 09 06 00, SCHEDULE FOR FINISHES.
F. Manufactured toilet and bath accessories: Section 10 28 00, TOILET, BATH, AND LAUNDRY
ACCESSORIES.

10 28 00 TOILET, BATH & LAUNDRY ACCESSORIES 1

1.3 SUBMITTALS
A. Submit in accordance with Section 01 33 23, SHOP DRAWINGS, PRODUCT DATA, AND
SAMPLES.
B. Shop Drawings:
1. Each product specified.
2. Paper towel dispenser and combination dispenser and disposal units.
3. Metal framed mirrors, showing shelf where required, fillers, and design and installation of units
when installed on ceramic tile wainscots and offset surfaces.
4. Shower Curtain rods, showing required length for each location.
5. Grab bars, showing design and each different type of anchorage.
6. Medicine cabinets showing design and installation.
7. Foot operated soap dispenser, showing anchorage and components.
8. Show material and finish, size of members, and details of construction, installation and
anchorage of mop racks.
C. Samples:
1. One of each type of accessory specified.
2. After approval, samples may be used in the work.
D. Manufacturer's Literature and Data:
1. All accessories specified.
2. Show type of material, gages or metal thickness in inches, finishes, and when required,
capacity of accessories.
3. Show working operations of spindle for toilet tissue dispensers.
4. Mop racks.
E. Manufacturer's Certificates:
1. Attesting that soap dispensers are fabricated of material that will not be affected by liquid soap
or aseptic detergents, Phisohex and solutions containing hexachlorophene.
2. Anodized finish as specified.
1.4 QUALITY ASSURANCE
A. Each product shall meet, as a minimum, the requirements specified, and shall be a standard
commercial product of a manufacturer regularly presently manufacturing items of type specified.

10 28 00 TOILET, BATH & LAUNDRY ACCESSORIES 2

 B. Each accessory type shall be the same and be made by the same manufacturer.
C. Each accessory shall be assembled to the greatest extent possible before delivery to the site.
D. Include additional features, which are not specifically prohibited by this specification, but which are
a part of the manufacturer's standard commercial product.
1.5 PACKAGING AND DELIVERY
A. Pack accessories individually to protect finish.
B. Deliver accessories to the project only when installation work in rooms is ready to receive them.
C. Deliver inserts and rough-in frames to site at appropriate time for building-in.
D. Deliver products to site in sealed packages of containers; labeled for identification with
manufacturer's name, brand, and contents.
1.6 STORAGE
A. Store products in weathertight and dry storage facility.
B. Protect from damage from handling, weather and construction operations before, during and after
installation in accordance with manufacturer's instructions.
1.7 APPLICABLE PUBLICATIONS
A. Publications listed below form a part of this specification to the extent referenced. Publications are
referenced in the text by the basic designation only.
B. American Society for Testing and Materials (ASTM):
A167-99(R2009) ......................... Stainless and Heat-Resisting Chromium-Nickel Steel Plate, Sheet
and Strip.
A176-99(R2009) ......................... Stainless and Heat-Resisting Chromium Steel Plate, Sheet, and
Strip
A269-10 ...................................... Seamless and Welded Austenitic Stainless Steel Tubing for
General Service
A312/A312M-09 ......................... Seamless and Welded Austenitic Stainless Steel Pipes
A653/A653M-10 ......................... Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated
(Galvannealed) by the Hot-Dip Process
B221-08 ...................................... Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire,
Shapes, and Tubes
B456-03(R2009) ......................... Electrodeposited Coatings of Copper Plus Nickel Plus Chromium
and Nickel Plus Chromium

10 28 00 TOILET, BATH & LAUNDRY ACCESSORIES 3

 C1036-06 .................................... Flat Glass
C1048-04 .................................... Heat-Treated Flat Glass-Kind HS, Kind FT Coated and Uncoated
Glass
D635-10 ...................................... Rate of Burning and/or Extent and Time of Burning of Self
Supporting Plastics in a Horizontal Position
F446-85(R2009) ......................... Consumer Safety Specification for Grab Bars and Accessories
Installed in the Bathing Area.
D3453-07 .................................... Flexible Cellular Materials - Urethane for Furniture and
Automotive Cushioning, Bedding, and Similar Applications
D3690-02(R2009) ....................... Vinyl-Coated and Urethane-Coated Upholstery Fabrics
C. The National Association of Architectural Metal Manufacturers (NAAMM):
AMP 500 Series.......................... Metal Finishes Manual
D. American Welding Society (AWS):
D10.4-86 (R2000) ....................... Welding Austenitic Chromium-Nickel Stainless Steel Piping and
Tubing
E. Federal Specifications (Fed. Specs.):
A-A-3002 .................................... Mirrors, Glass
FF-S-107C (2) ............................ Screw, Tapping and Drive
FF-S-107C .................................. Screw, Tapping and Drive.
WW-P-541E(1) ........................... Plumbing Fixtures (Accessories, Land Use) Detail Specification
PART 2 - PRODUCTS
2.1 MATERIALS
A. Aluminum: ASTM B221, alloy 6063-T5 and alloy 6463-T5.
B. Stainless Steel:
1. Plate or sheet: ASTM A167, Type 302, 304, or 304L, except ASTM A176 where Type 430 is
specified, 0.0299-inch thick unless otherwise specified.
2. Tube: ASTM A269, Alloy Type 302, 304, or 304L.
C. Stainless Steel Tubing: ASTM A269, Grade 304 or 304L, seamless or welded.
D. Stainless Steel Pipe: ASTM A312; Grade TP 304 or TP 304L.
E. Steel Sheet: ASTM A653, zinc-coated (galvanized) coating designation G90.

10 28 00 TOILET, BATH & LAUNDRY ACCESSORIES 4

 F. Glass:
1. ASTM C1036, Type 1, Class 1, Quality q2, for mirrors, and for mirror doors in medicine
cabinets.
2. ASTM C1036, Type 1 Class 1 Quality q3, for shelves in medicine cabinets.
G. Foam Rubber: ASTM D3453, Grade BD, Type 2.
H. Vinyl Covering: ASTM D3690, Vinyl coated fabric, Class A.
I. Plywood: PS1, Grade CD.
2.2 FASTENERS
A. Exposed Fasteners: Stainless steel or chromium plated brass, finish to match adjacent surface.
B. Concealed Fasteners: Steel, hot-dip galvanized (except in high moisture areas such as showers or
bath tubs use stainless steel).
C. Toggle Bolts: For use in hollow masonry or frame construction.
D. Hex bolts: For through bolting on thin panels.
E. Expansion Shields: Lead or plastic as recommended by accessory manufacturer for component
and substrate for use in solid masonry or concrete.
F. Screws:
1. ASME B18.6.4.
2. Fed Spec. FF-S-107, Stainless steel Type A.
G. Adhesive: As recommended by manufacturer for products to be joined.
2.3 FINISH
A. In accordance with NAAMM AMP 500 series.
B. Anodized Aluminum:
1. AA-C22A41 Chemically etched medium matte, with clear anodic coating, Class I Architectural,
0.7-mil thick.
2. AA-C22A44Chemically etched medium matte with electrolytically deposited metallic
compound, integrally colored coating Class I Architectural, 0.7-mil thick finish. Dyes will not be
accepted.
C. AA-M32 Mechanical finish, medium satin.
1. Chromium Plating: ASTM B456, satin or bright as specified, Service Condition No. SC2.
2. Stainless Steel: NAAMM AMP 503, finish number 4.

10 28 00 TOILET, BATH & LAUNDRY ACCESSORIES 5

 3. Ferrous Metal:
a. Shop Prime: Clean, pretreat and apply one coat of primer and bake.
b. Finish: Over primer apply two coats of alkyd or phenolic resin enamel, and bake.
4. Nylon Coated Steel: Nylon coating powder formulated for a fluidized bonding process to steel
to provide a hard smooth, medium gloss finish, not less than 0.3 mm (0.012-inch) thick, rated
as self-extinguishing when tested in accordance with ASTM D635.
2.4 FABRICATION - GENERAL
A. Welding, AWS D10.4.
B. Grind dress, and finish welded joints to match finish of adjacent surface.
C. Form exposed surfaces from one sheet of stock, free of joints.
D. Provide steel anchors and components required for secure installation.
E. Form flat surfaces without distortion. Keep exposed surfaces free from scratches and dents.
Reinforce doors to prevent warp or twist.
F. Isolate aluminum from dissimilar metals and from contact with building materials as required to
prevent electrolysis and corrosion.
G. Hot-dip galvanized steel, except stainless steel, anchors and fastening devices.
H. Shop assemble accessories and package with all components, anchors, fittings, fasteners and
keys.
I. Key items alike.
J. Provide templates and rough-in measurements as required.
K. Round and deburr edges of sheets to remove sharp edges.
2.5 PAPER TOWEL DISPENSERS
A. Surface mounted type with sloping top.
B. Dispensing capacity for 300 sheets of any type of paper toweling.
C. Fabricate of stainless steel.
D. Provide door with continuous hinge at bottom, and either spring tension cam lock or tumbler lock,
keyed alike, at top and a refill sight slot in front.
2.6 COMBINATION PAPER TOWEL DISPENSER AND DISPOSAL UNITS
A. Recessed and semi-recessed type.
B. Dispensing capacity for 400 sheets of any type of paper toweling.
C. Fabricate of stainless steel.

10 28 00 TOILET, BATH & LAUNDRY ACCESSORIES 6

 D. Form face frames, from one piece.
E. Provide each door with continuous stainless steel piano hinge and tumbler lock, keyed alike.
F. Provide removable waste receptacle approximately 40 liter (10.5 gallon) capacity, fabricated of
0.45 mm (0.018-inch) thick stainless steel.
2.7 WASTE RECEPTACLES
A. Semi-recessed type, without doors.
B. Fabricate of stainless steel.
C. Form face frame from one piece.
D. Provide removable waste receptacle of approximately (12 gallon) capacity, fabricated of stainless
steel.
E. Waste receptacle key locked in place.
2.8 TOILET TISSUE DISPENSERS
A. Double roll surface mounted type.
B. Mount on continuous backplate.
C. Removable spindle ABS plastic or chrome plated plastic.
D. Wood rollers are not acceptable.
2.9 SHOWER CURTAIN RODS
A. Stainless steel tubing, ASTM A569, minimum 1.27 mm (0.050 inch) wall thickness, 32 mm (1 1/4
inch) outside diameter.
B. Flanges, stainless steel rings, 66 mm (2 5/8 inch) minimum outside diameter, with 2 holes opposite
each other for 6 mm (1/4 inch) stainless steel fastening bolts. Provide a set screw within the
curvature of each flange for securing the rod.
C. Intermediate support for rods over 1800 mm (six feet) long. Provide adjustable ceiling flanges with
set screws, tubular hangers and stirrups.
D. Shower curtain rods in Mental Health and Behavioral Nursing Units:
1. Chrome plated plastic rods capable of supporting 22.6 Kg (50 pounds) before pulling free of
wall flanges.
2. Option: Ceiling mounted hospital cubicle curtain tracks as specified in Section 10 21 23,
CUBICLES, with break away pendant chain hooks. Chain hooks located at 2000 mm (80
inches) above floor.

10 28 00 TOILET, BATH & LAUNDRY ACCESSORIES 7

2.10 TOWEL BARS
A. Fed. Spec. WW-P-541/8B, Type IV, Bar, Surface mounted; Class 1, towel.
B. Either stainless steel, or chromium plated copper alloy.
C. Bar Length: 450 and 600 mm (18 and 24 inches) as shown.
D. Finish of brackets or supports same as bar.
2.11 METAL FRAMED MIRRORS
A. Fed. Spec. A-A-3002 metal frame; chromium finished steel , anodized aluminum or stainless
steel, type 302 or 304.
B. Mirror Glass:
1. Minimum 6 mm (1/4 inch) thick.
2. Set mirror in a protective vinyl glazing tape.
3. Use tempered glass for mirrors in Mental Health and Behavioral Nursing units.
C. Frames:
1. Channel or angle shaped section with face of frame not less than 9 mm (3/8 inch) wide.
Fabricate with square corners.
2. Use either 0.9 mm (0.0359 inch) thick stainless steel, chrome finished steel, or extruded
aluminum, with clear anodized finish 0.4 mils thick.
3. Filler:
a. Where mirrors are mounted on walls having ceramic tile wainscots not flush with wall
above, provide fillers at void between back of mirror and wall surface.
b. Fabricate fillers from same material and finish as the mirror frame, contoured to conceal
the void behind the mirror at sides and top.
4. Attached Shelf for Mirrors:
a. Fabricate shelf of the same material and finish as the mirror frame.
b. Make shelf approximately 125 mm (five inches) in depth, and extend full width of the
mirror.
c. Close the ends and the front edge of the shelf to the same thickness as the mirror frame
width.
d. Form shelf for aluminum framed mirror as an integral part of the bottom frame member.
Form stainless steel shelf with concealed brackets to attach to mirror frame.

10 28 00 TOILET, BATH & LAUNDRY ACCESSORIES 8

 D. Back Plate:
1. Fabricate backplate for concealed wall hanging of either zinc-coated, or cadmium plated 0.9
mm (0.036 inch) thick sheet steel, die cut to fit face of mirror frame, and furnish with theft
resistant concealed wall fastenings.
2. Use set screw type theft resistant concealed fastening system for mounting mirrors.
E. Mounting Bracket:
1. Designed to support mirror tight to wall.
2. Designed to retain mirror with concealed set screw fastenings.
2.12 SOAP DISHES
A. Fed. Spec. WW-P-541/8B, Type VI, Holder.
B. Class 1, Surface Mounted:
1. One piece with provisions for exposed fasteners.
2. Fabricate from chromium plated brass approximately 115 by 95 mm (4 1/2 by 3-3/4 inches)
overall size with drainage openings at bottom.
C. Class 2, Recessed:
1. One piece seamless shell and flange with provisions for concealed fasteners.
2. Fabricate from either chromium plated brass, or 0.8 mm (0.0329 inch) thick stainless steel.
3. Form surface of soap tray with raised ridges or patterned dimples to provide gripping surface
for soap bar, or provide flush soap tray with a retaining lip. Plastic soap trays or tray inserts are
not acceptable.
PART 3 - EXECUTION
3.1 PREPARATION
A. Before starting work notify HDC Clerk of Work in writing of any conflicts detrimental to installation
or operation of units.
B. Verify with the HDC Clerk of Work the exact location of accessories.
3.2 INSTALLATION
A. Set work accurately, in alignment and where shown. Items shall be plumb, level, free of rack and
twist, and set parallel or perpendicular as required to line and plane of surface.
B. Toggle bolt to steel anchorage plates in frame partitions or hollow masonry. Expansion bolt to
concrete or solid masonry.
C. Install accessories in accordance with the manufacturer's printed instructions and ASTM F446.

10 28 00 TOILET, BATH & LAUNDRY ACCESSORIES 9

 D. Install accessories plumb and level and securely anchor to substrate.
E. Install accessories in a manner that will permit the accessory to function as designed and allow for
servicing as required without hampering or hindering the performance of other devices.
F. Position and install dispensers, and other devices in countertops, clear of drawers, permitting
ample clearance below countertop between devices, and ready access for maintenance as
needed.
G. Align mirrors, dispensers and other accessories even and level, when installed in battery.
H. Install accessories to prevent striking by other moving, items or interference with accessibility.
I. Install wall mirrors in Mental Health and Behavioral Units with tamper resistant screws that are
flush mounted so that they will not support a rope or material for hanging.

3.3 SCHEDULE OF ACCESSORIES

3.4 CLEANING
After installation, clean as recommended by the manufacturer and protect from damage until
completion of the project.
---END---

10 28 00 TOILET, BATH & LAUNDRY ACCESSORIES 10