Tips for an Accurate Measurement Recommendations for Users

• It is important that the sample does not contain any debris. Before using Hanna Instruments products, make sure that they are entirely suitable for
your specific application and for the environment in which they are used. Operation of
INSTRUCTION MANUAL
• Whenever the cuvette is placed into the measurement cell, it
must be dry outside, and completely free of fingerprints, oil and these instruments may cause unacceptable interferences to other electronic equipment, thus
dirt. Wipe it thoroughly with HI731318 or a lint-free cloth prior
to insertion.
requiring the operator to take all necessary steps to correct such interferences. Any variation
introduced by the user to the supplied equipment may degrade the instrument’s EMC
HI702
• Shaking the cuvette can generate bubbles, causing higher
performance. To avoid damages or burns, do not put the instrument in microwave oven. For Copper High Range
yours and the instrument safety do not use or store the instrument in hazardous environments.
readings. To obtain accurate measurements, remove such bubbles
by swirling or by gently tapping the cuvette.
• Do not let the reacted sample stand for too long after reagent
is added, as accuracy will be affected. Accessories
• After the reading it is important to immediately discard the Reagent Sets
sample, otherwise the glass might become permanently stained. HI702-25 Reagents for 25 Copper High Range tests
Other Accessories
Battery Management HI702-11 Copper HR Certified Standard Kit
To save the battery, the instrument shuts down after 10 minutes of non-use. HI731225 Cuvette Black Cap for Checker® HC Colorimeters (4 pcs.)
One fresh battery lasts for a minimum of 5000 measurements. When the battery is dead the HI731318 Cloth for wiping cuvettes (4 pcs.)
instrument will display “bAd” then ”bAt” for 1 second and then turns off. HI731321 Glass cuvettes and Seal Cap for Checker® HC Colorimeters (4 pcs.)
To restart the instrument, the battery must be replaced with a new one. HI731353 Cuvette Seal Cap for Checker® HC Colorimeters (4 pcs.)
HI740028P 1.5V AAA batteries (12 pcs.)
To replace the instrument’s battery:
HI93703-50 Cuvette cleaning solution (230 mL)
• Turn the instrument off by holding the button until the meter shuts off.
• Turn the instrument upside down and remove the battery cover with a screwdriver.
Warranty
HI702 is warranted for a period of one year after date of purchase against defects in
workmanship and materials when used for their intended purpose and maintained according
to instructions. This warranty is limited to repair or replacement free of charge. Damage due
to accidents, misuse, tampering or lack of prescribed maintenance is not covered. If service
is required, contact your local Hanna Instruments Office. If under warranty, report the model
number, date of purchase, serial number and the nature of the problem. If the repair is not
covered by the warranty, you will be notified of the charges incurred. If the instrument is to
be returned to Hanna Instruments, first obtain a Return Goods Authorization number from the
Technical Service department and then send it with shipping costs prepaid. When shipping any
• Remove the battery from its location and replace it with a new one, inserting the negative instrument, make sure it is properly packed for complete protection.
end first.
• Insert the battery cover and replace the screw with a screwdriver. IST702 05/18
Thank You Functional Description Measurement Procedure
Thank you for choosing a Hanna Instruments product. Please read this instruction • Turn the meter on by pressing the button. All
Cover segments are displayed. When the display
manual carefully before using the instrument.
For more information about Hanna Instruments and our products, visit Cuvette with cap shows “Add”, “C.1” with “Press” blinking,
www.hannainst.com. the meter is ready.
Cuvette holder
For technical support, contact your local Hanna Instruments Office or e-mail us at
[email protected].
LCD Liquid Crystal Display • Fill the cuvette with 10 mL of unreacted
Find your local Hanna Instruments Office on www.hannainst.com.
sample and replace the cap. Place the cuvette
Operation Button into the meter and close the meter’s cap.
Preliminary Examination
Please examine this product carefully. Make sure that the instrument is not damaged. If
any damage occurred during shipment, please contact your local Hanna Instruments Office. Errors and Warnings • Press the button. When the display shows
“Add”, “C.2” with “Press” blinking the meter
Each HI702 meter is supplied complete with:
Light High: There is too much light to perform a measurement. Please is zeroed.
• Sample Cuvettes and Caps (2 pcs.)
check the preparation of the zero cuvette.
• Reagents for 6 tests
• 1.5V AAA Battery (1 pc.) Light Low: There is not enough light to perform a measurement. Please
• Remove the cuvette from the meter and
• Instruction Manual and Quick Reference Guide check the preparation of the zero cuvette.
unscrew the cap. Add the content of one
Inverted Cuvettes: The sample and the zero cuvette are inverted. packet of HI702-0 reagent. Replace the cap
Specifications and shake gently for about 15 seconds. Place
Range 0.00 to 5.00 ppm the cuvette back into the meter.
Under Range: A blinking “0.00” indicates that the sample absorbs less
Resolution 0.01 ppm
light than the zero reference. Check the procedure and make sure you use
Accuracy ±0.05 ppm ±5% of reading @25 °C/77 °F the same cuvette for reference (zero) and measurement. • Press and hold the button until the timer is
Light Source Light Emitting Diode @575 nm Over Range: A flashing value of the maximum concentration indicates displayed on the LCD (the display will show
the countdown prior to the measurement) or,
Light Detector Silicon Photocell the reading is over range. Dilute the sample and re-run the test.
alternatively, wait for 45 seconds and press
Adaptation of the EPA approved method. The reaction between the button.
Method copper and the bicinchoninate reagent causes a purple tint in the Battery Low: The battery must be replaced soon.
sample.
Environment 0 to 50 °C (32 to 122 °F); max 95% RH non-condesing • The instrument displays the concentration of
Dead Battery: This indicates that the battery is dead and must be copper in ppm. The meter automatically turns
Battery Type 1.5V AAA (1 pc.) replaced. Once this indication is displayed, normal operation of the off after 10 minutes.
Auto-Shut off After 10 minutes of non-use instrument will be interrupted. Change the battery and restart the meter.
Dimensions 86.0 x 61.0 x 37.5 mm (3.4 x 2.4 x 1.5”)
Hanna Instruments reserves the right to modify the design, construction or appearance of
Weight 52 g (1.84 oz.) its products without advance notice.