Kodo build guide 1.

Thank you for purchasing KRAGA Kodo and supporting me.

Please do not share files that you bought

Development of a new plane and support of the old ones is very time consuming. Only with your
help I can focus fully on this project and spend some quality time with my family.

[email protected]
 13 12
56 14
66
63 29
62 33
57 ITEM NO. PART NUMBER PRINTED AS QTY.
28
1 boom_10x9_520 - 1
9 2 fuse_bottom_spar_2x1_425 - 1
32 3 aileron_spar_2x1_270 - 2
58 4 fuse_left_spar_2x1_407 - 1
1
5 fuse_right_spar_2x1_407 - 1
59 6 hinge - 10
68 7 main_wing_spar_4x3_375 - 2
25 8 main_wing_spar_6x4_375 - 2
9 servo_common - 2
17
10 spar_joiner_3_220_b - 1
67 11 spar_joiner_4_250_f - 1

26 12 tail_main_spar_2x1_b_145 - 2
13 tail_main_spar_2x1_f_132 - 2
30 14 tail_mov_spar_2x1_105 - 2
6 15 tip_wing_spar_4x3_b_400 - 2
27
51 16 tip_wing_spar_4x3_f_397 - 2
31 17 boom_lines_holder SOLID 3
70
18 fuse_0 SOLID 1
19 fuse_1 SOLID 1
14
20 fuse_2 SOLID 1
3 21 fuse_3 SOLID 1
15 12 22 fuse_4_sk3_2836 SOLID 1
23 canopy_front SOLID 1
24 canopy_rear SOLID 1
13 25 tail_boom_mount SOLID 1
16 26 tail_main_L_0 SHELL 1
27 tail_main_L_1 SHELL 1
50 ? 28 tail_main_R_0 SHELL 1
29 tail_main_R_1 SHELL 1
30 tail_mov_L_0 SHELL 1
49
? 31 tail_mov_L_1 SHELL 1
32 tail_mov_R_0 SHELL 1
48 33 tail_mov_R_1 SHELL 1
9
8 34 center_wing_L_0 SHELL 1
35 center_wing_L_1 SHELL 1
65
36 center_wing_L_2 SHELL 1
?
37 center_wing_L_3 SHELL 1
52 38 center_wing_R_0 SHELL 1
7 39 center_wing_R_1 SHELL 1
40 center_wing_R_2 SHELL 1
41 center_wing_R_3 SHELL 1
? 53
42 tip_wing_L_0 SHELL 1
43 tip_wing_L_1 SHELL 1
44 tip_wing_L_2 SHELL 1
? 54 45 tip_wing_L_3 SHELL 1
46 tip_wing_L_4 SHELL 1
47 tip_wing_R_0 SHELL 1
? 55 48 tip_wing_R_1 SHELL 1
49 tip_wing_R_2 SHELL 1
50 tip_wing_R_3 SHELL 1
3 51 tip_wing_R_4 SHELL 1
?
52 aileron_L_0 SHELL 1
69 53 aileron_L_1 SHELL 1
54 aileron_L_2 SHELL 1
10 55 aileron_L_3 SHELL 1
15 56 aileron_R_0 SHELL 1
57 aileron_R_1 SHELL 1
5 58 aileron_R_2 SHELL 1
59 aileron_R_3 SHELL 1
4 16 60 servo_common_mount_wing_front_L SOLID 1
61 servo_common_mount_wing_rear_L SOLID 1
46
2 62 servo_common_mount_wing_front_R SOLID 1
45 63 servo_common_mount_wing_rear_R SOLID 1
64 servo_mount_fuse SOLID 1
44
65 wing_horn_L SOLID 1
23 66 wing_horn_R SOLID 1
67 tail_horn_L SOLID 1
43
22 68 tail_horn_R SOLID 1
69 end_cap_L SOLID 1
21 8 70 end_cap_R SOLID 1

24 61
20 60
? ?
19 11 7
18 ? ?
Printing
You need to use two printing methods to print all parts:

1. Solid parts (fuse and accessories - all blue parts). Use dense infill.
This is common way of printing objects and these parts should be
printable on every printer.

2. Shell parts (wings - all orange parts). Use 0% infill and

no horizontal surfaces (thickness of the shell is one
layer). Only this way you can achieve required weight of
the plane.

You can check what method to use on what part in bill of materials table.

Nozzle size: 0.4 mm

Rafts: yes

You can use any material you like, only limitation is high temperature from ironing when covering
assembled parts. Heat from the iron can deform the parts. Although I was not able to damage any
part and I tried to cover many materials (ABS, PLA ...), please test film covering on your testing
part.

One of the goals when designing KRAGA models was to use minimal or no support during printing.
Removing support after printing is big pain and you can easily destroy your part. That is the reason
why you should use default orientation of all parts during printing. There are only two parts from
whole plane which require support, these are from plane fuselage and are printed as solid. The rest
of the plane should be support-free.

I strongly recommend to mark every printed part with it's name (I'm using masking tape for that).
There are many parts in this plane and from each part there is also mirror side which can easily
cause confusion during assembly.

I also recommend to print parts in bulks, especially smaller parts like ailerons or moving parts on
the plane tail. Otherwise there is not enough time for material cooling in each layer and you might
end up with rough layers, ugly edges or print fail.

[email protected]
Parts choices

For some parts there are more options and it is up to you what you will choose depending on what
motor and servos are you going to use.

Choices based on used motor:

• no motor (pure sailplane variant): print fuse_4_no_motor and fuse_5
• Turnigy Aerodrive SK3 - 2836 brushless outrunner motor: print fuse_4_sk3_2836 (fuse_5
not needed)
• other motor: print fuse_4_uni, for this option you need to drill motor screw holes manually
(fuse_5 not needed)

Choices based on used servo in the wing:

• servo_hxt_900_mount: will fit HXT900 servo A = 2.4 mm, B = 23
mm, C = 32 mm, D = 12 mm, E = 16 mm
• servo_common_mount: will fit A = 2 mm, B = 23 mm,
C = 32 mm, D = 12 mm, E = 19 mm
• servo_custom_mount: you can cut out slots yourself
based on your needs
Most important dimension is A, if that one fits you but the other ones not try to print the mounts anyway and test-fit your servo.

Choices based on used servo in the fuselage:

• servo_mount_fuse: will fit servos with B = 23 mm, D = 12 mm

• servo_mount_fuse_common: you can cut out whatever hole you need

[email protected]
Preparation for assembly

KRAGA Kodo plane consists of parts that are printed and parts that you need to buy separately
(they are not included in sold product) – carbon tubes, rods and pinned hinges.
List of required parts:

dimensions count
carbon tube ⌀ 2x1 mm ↔ 1 m 3
carbon tube ⌀ 4x3 mm ↔ 1 m 3
carbon tube ⌀ 6x4 mm ↔ 1m 1
carbon tube ⌀ 10x9 mm ↔ 520 mm 1
carbon rod ⌀ 3 mm ↔ 220 mm 1
carbon rod ⌀ 4 mm ↔ 250 mm 1
covering film ↔2m 1
push rod * ↔ 80 cm 2
pinned hinge ↕ ↔ 16x28 mm or smaller 10
folding propeller up to ↔ 10 inch 1
spinner ⌀ 40 mm 1
⌀ 2x1 mm – means tube with outer diameter of 2mm and inner diameter of 1mm
⌀ 3 mm - means rod with diameter of 3mm
* you can use other linkage system than flexible push rod (push rod made from carbon tube ...)

And of course you need all the common accessories like clevises, push rods for ailerons, (horns are
printed so you don't need those) and electronics (motor, esc, 4 micro servos).

[email protected]
Next step is to cut carbon tubes and rods into smaller pieces, which will be used as spars, joiners or
boom of the plane. Don't forget to mark every piece to avoid confusion during the assembly.

part dimensions count

aileron carbon spar ⌀ 2x1 mm ↔ 270 mm 2
fuse bottom carbon spar ⌀ 2x1 mm ↔ 425 mm (*438 mm) 1
fuse side carbon spar ⌀ 2x1 mm ↔ 407 mm (*420 mm) 2
tail main carbon spar front ⌀ 2x1 mm ↔ 132 mm 2
tail main carbon spar back ⌀ 2x1 mm ↔ 145 mm 2
tail mov carbon spar ⌀ 2x1 mm ↔ 105 mm 2
tip wing carbon spar front ⌀ 4x3 mm ↔ 397mm 2
tip wing carbon spar back ⌀ 4x3 mm ↔ 400 mm 2
center wing carbon spar back ⌀ 4x3 mm ↔ 375 mm 2
center wing carbon spar front ⌀ 6x4 mm ↔ 375 mm 2
carbon boom ⌀ 10x9 mm ↔ 520 mm 1
wing joiner carbon rod back ⌀ 3 mm ↔ 220 mm 1
wing joiner carbon rod front ⌀ 4 mm ↔ 250 mm 1
* dimensions for pure sailplane variant

TIP: How to cut carbon spars. Wrap masking tape

around carbon spar and mark cut position. Use rotary
tool to cut the spar. Work outside or in room with
good ventilation. Use breathing mask to avoid
inhaling carbon dust! After cutting wipe out carbon
dust from the spars using wet tissue.

Remove support legs from all parts. Also sand all sharp edges
and printing imperfections to avoid covering foil damage.

[email protected]
Assembly
This assembly will describe always left side of the plane when it comes to symmetric parts. It is
recommended to use medium viscosity CA glue. You can use CA glue accelerator for faster curing
time. Dry fit all the parts before gluing them together.

Center wing

Assembly left center wing as sketched above. Carbon spars should be aligned flush with base of
center_wing_L_0 part. When all the parts are on their position, put glue on contact points where
carbon spars are touching printed parts.

[email protected]
Tip wing

Assembly left tip wing as sketched above. You have an option here to use common servo mounts or
servo mounts for HXT900. Don't forget to insert servo mounts into tip_wing_L_0 part when
leading spars through. Carbon spars protrude from base of tip_wing_L_0 so that they can be
inserted into empty leading spar holes on the center wing. Do not forget to center your servos before
gluing them in. Check also that your clevises fit servo arm holes, drilling them when servo is in
place could damage the wing.
You can choose to use end cap for the wing tip. It is not mandatory, but it makes film covering a
little bit easier.
When all the parts are on their position, put glue on contact points where carbon spars are touching
printed parts.

[email protected]
Aileron

Assembly left aileron as sketched above. Don't forget to insert wing_horn_L part into aileron_L_0
when leading spar through. Carbon spars should be aligned flush with base of aileron_L_0 part.
When all the parts are on their position, put glue on contact points where carbon spars are touching
printed parts.

[email protected]
Wing

To complete wing assembly first glue together center wing and tip wing. Only then continue with
gluing hinges and aileron.
Some hinge slots are not deep enough to fit whole hinge length. Shorten all
hinges as shown on the picture. It has no benefit in terms of added stiffness
of rigidity to use whole hinge arm length as only small hinge area is in
contact with the wing.
Be careful when using glue near pinned part of the hinge. First insert the hinge into hinge hole and
then apply the glue from inner side of the wing. Do the same when gluing aileron to hinge. First
insert all hinges into hinge holes on aileron and then apply glue from inner side of aileron. Make
sure that aileron has enough space for moving from every side.
When the wing is assembled lead servo cable through the wing. The cable should come out of the
wing near servo cable hole in fuselage.

[email protected]
Tail main

Assembly left main tail as sketched above. Carbon spars protrude 1 cm from base of tail_main_L_0.
When all the parts are on their position, put glue on contact points where carbon spars are touching
printed parts.

Tail mov

Assembly left tail as sketched above. Carbon spar should be centered in the middle. When all the
parts are on their position, put glue on contact points where carbon spars are touching printed parts.

[email protected]
Tail

To complete tail assembly first shorten all hinges and then insert the hinges into hinge slots and
apply the glue from inner side of the main tail. Then insert all hinges into hinge slots on moving
part of the tail and put the glue from inner side of the moving part. Tip of the moving part should be
aligned flush with main part.

[email protected]
Fuselage front

Start by gluing together boom and fuse_0. Boom should be aligned flush with base side of fuse_0.
When these two parts are aligned apply glue from both sides of fuse_0.
Then insert all three spars into fuse_0. Apply the glue from inner side of fuse_0. There are spaces in
spar leading tubes where you can put the glue and let it leak further into places which are hard to
reach.
Insert and center back joiner rod into holes in fuse_1. Glue it in the place from inside of the
fuselage. Then insert carbon fuse spars into spar leading tubes in fuse_1 and slide it all the way until
it is touching fuse_0. Then apply glue from inner side of the fuselage.
Put servo mount plate (optionally you can drill servo mounting holes into the plate beforehand) into
fuse_2 part and lead front joiner rod through holes in fuse_2 and hole in servo plate. Apply the glue
to secure servo plate and joiner rod in place. Insert carbon fuse spars into spar leading tubes in
fuse_2 and slide it all the way until it is touching fuse_1. Then apply glue from inner side of the
fuselage.
Now you can continue with rest of fuse parts. Always put each part on their position and only then
apply the glue from inner side.
If you opted for sailplane without motor then fuse spars are protruding 13 mm from the
fuse_4_no_motor and you can glue fuse_5 to these. Otherwise fuse spars should be aligned flush
with fuse_4_* when you are done with all parts.

[email protected]
Fuselage back

Glue together both sides of the tail with tail_boom_mount. Apply the glue only after tail parts are
joined with tail_boom_mount.
Insert boom into tail_boom_mount. Aline the tail correctly with rest of the fuselage (use joiner rods
as helping guide). Then you can put the glue from inner side of the tail_boom_mount where it is
touching the boom.
There are multiple ways how to make linkage to the tail moving surfaces. If you opted for flexible
type, you can use push rods holders to restrict their bending in boom.

[email protected]
Covering

There is nothing special about covering 3D printed planes. It is done the same way as you would do
with common balsa RC plane. It is important to test film covering on testing part before you start.
If you have no experience with film covering my advice is to try more brands of covering film
before you get frustrated. It is easier to work with some than with other. I tested couple of brands
and in my opinion solarfilm lite is the best option for this kind of plane.
My recommendation is to cover wings after they are fully assembled (center wing, tip wing and
aileron are glued together). It is a little bit more demanding but it is definitely worth it. Otherwise
you are risking that when gluing aileron to hinges and hinges to wing tip, glue might leak and
spread all over hinge pin which will block the hinge and aileron would get stuck.
The same is valid for tail covering. Cover it after you glued on the moving part with hinges.

[email protected]
Electronics
This is by no means the best way possible how to setup your plane. It is just a brief overview of
possible affordable options.

Motor
To avoid problems when setting correct CG, it is recommended to use motor weighting 80g. Inner
diameter of the fuselage is 38mm. You should be able to fit inside motors with diameter up to
30mm.
Good option is Turnigy Aerodrive SK3 - 2836-1040kv Brushless Outrunner – with this motor Kodo
will be no rocket. But it is enough for a little bit of fun. Part fuse_4_sk3_2836 has prepared
mounting holes for this motor.

ESC
If you opted for above mentioned motor option, you need 40A speed controller for brushless motors
ideally with SBEC, for example this one: HobbyKing 40A BlueSeries Brushless Speed Controller.

Battery
There are two basic setups:
• If you want to have small wing loading to do more thermal
flying - install battery and ESC next to each other (in
parallel) into the front area of the fuselage. To fit the
battery into fuselage in such config it needs to be maximally 20mm thick, 30mm high and
80g heavy. Good options are: Turnigy nano-tech 950mah 3S 25~50C Lipo Pack or Turnigy
1250mAh 3S 30C Lipo Pack (Long).
• For more flying under power – install
battery behind the ESC (in series). In this
configuration bigger and heavier battery
will fit inside of the fuselage. Turnigy nano-tech 1500mah 3S 25~50C Lipo Pack is one of
many options.

Receiver
This depends on your transmitter. Only requirement is to have 5 channels or 4 if you are going for
pure glider (no motor).

Servos
Good and affordable option which will fit nicely into Kodo is Turnigy TGY-9018MG MG. It is an
analog servo with metal gears. You can use 4 of these (2 in the wings, 2 in the fuselage).

[email protected]
Settings and flying
CG
63 mm – 66 mm from wing leading edge measured next to the wing root.
I strongly recommend to use 63mm for first flight. Setting your CG exactly is very important!

Template for tail zero position

You can print this template, cut it out of the paper and use it for setting zero position of the tail.

Wings to fuselage attachment

There are no or only very little forces acting on the wings in horizontal direction. There is no need
to attach wings too firmly to the fuselage. It also helps to absorb the energy during landing when the
wings can detach easily.
Joiner rods on the fuselage have diameter of 3 and 4 mm, carbon spars in wings have inner diameter
of 3 and 4 mm. To attach wing to the fuselage insert joiner rods into wing spars. Use tape to secure
the wing where trailing edge of the wing is touching the fuselage.

Happy flying
Tomas

[email protected]