Scribd
Upload
13 views

R9 MM-OTA -Manual

Uploaded by

uddgaye26
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
13 views

R9 MM-OTA -Manual

Uploaded by

uddgaye26
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Instruction Manual for FrSky R9 MM-OTA Receiver

Introduction
The 900MHz R9 MM-OTA receiver implements the ACCESS protocol and brings the user improved performance and features. The R9
MM-OTA supports wireless firmware updates over the air making binding to receivers even easier. As well as the convenience of
checking the current receiver firmware version. The R9 MM’s compact form factor design is also carried over to the OTA version, and
the R9 MM-OTA supports inverted S.Port as well. In order to fully enjoy the benefits of this system, please read the instruction manual
carefully and set up the device as described below.

Overview

CH1
CH2
CH3
CH4
SBUS_OUT Red LED Green LED Status
1 2 3 4 On On Register
S.PORT/F.PORT

GND Flash Flash Register successfully

10
Off On Bind
V_IN
Off Flash Work Normally
Inverted S.Port
Flash Off Failsafe

16

Specifications
• Dimension: 16*10*2.8mm (L × W ×H)
• Weight: 0.7g (without antenna)
• Numbers of channel:

R9 MM-OTA LBT Version Non-LBT Version

TX Mode Telemetry No telemetry Telemetry


Numbers of channel 4/16CH 4/16CH 4/16CH
• CH16 outputs RSSI
• Operating Voltage Range: DC 3.5V~10V
• Operating Current: 100mA@5V
• Operating Range: Up to 10km or above
• Operating Frequency: 915MHz (Non-LBT)/868MHz (LBT)
• Compatibility: R9M Lite/R9M Lite Pro/R9M 2019 with ACCESS

Features
• ACCESS Protocol and support OTA function
• Support S.Port (Support F.Port, download firmware to support functions)
• Battery Voltage detection supported
• Detachable Ipex connector antenna
• Low latency and high precision

Smart Port (S. Port) is a signal wire full duplex digital transmission interface developed by FrSky
Electronic Co., Ltd. All products enabled with Smart Port (including XJT module, XSR,X6R and X8R receiver,
new hub-less sensors, new Smart Dashboard, etc), serial port user data and other user input/output devices
can be connected without limitations for numbers or sequences at a high transmission speed.

Registration & Automatic binding (Smart Match TM )


With the FrSky ACCESS protocol, the transmitter/transmitter module can bind receiver without using the "F/S" button.
Follow the step below to finish the Registration & binding procedure:
1. Put the transmitter/transmitter module into [Reg] status.
1.1 For Taranis X-Lite Pro as an example, turn on the transmitter, go to the MENU-MODEL SETUP-PAGE 2, choose External RF-Mode
R9MLP ACCESS, then select [Reg].
2. Connect the battery to the receiver while holding the F/S button on the receiver. The RED LED and GREEN LED on the
receiver will be on, indicating into the [Reg] status. Select [ENTER] on the transmitter, The RED LED and GREEN LED on the receiver
will flash, and the transmitter displays [Registration ok].
3. Turn off the receiver.
4. Move the cursor to select the receiver 1 [Bind].
5. Connect the battery to the receiver, the GREEN LED on the receiver will be on, indicating into the [Bind] status. Select the RX, and
Instruction Manual for FrSky R9 MM-OTA Receiver
the transmitter displays [Bind successful].
6. The transmitter exit [Bind], GREEN LED will flash, RED LED will be off, indicating working normally

About OTA function


-- For Taranis X-Lite Pro as an example, go to the SD CARD 2/7, and select the FW, press the enter button, select [Flash receiver
OTA], power on the receiver, select the RX, go to the [ENTER], complete the flash process, the transmitter will display [Flash
successful]. Re-power the receiver and wait for 3 seconds, the Green LED starts flashing indicates the receiver works properly at the
momemnt.

Note: Update the firmware after the receiver gets bound.

How to enable/disable the receiver telemetry


-- For Taranis X-Lite Pro as an example, go to the External RF, select the Receiver, press the ENTER button, select the options,
and enable/disable the telemetry.

How to Set Failsafe mode (on the transmitter)


There are 3 failsafe modes: No Pulse, Hold, Custom
• No Pulse: on loss of signal the receiver produces no pulses on any channel. To use this type, select it in the menu and wait 9
seconds for the failsafe to take effect.
• Hold: the model will maintain the last position after the signal is lost. To use this type, select it in the menu and wait 9 seconds for
the failsafe to take effect.
• Custom: the customized position of each individual channel. The model will move to the pre-set position after the signal is lost. Move
the cursor to [Failsafe ][Custom][Set] and press ENTER, you will see FAILSAFE SETTING screen below. Move the cursor to the
channel you want to set failsafe on, and press ENTER. When moving the crresponding sticks or switches, you will see the channel
bar moving. Move the channel bar to the place you want for failsafe and long press ENTER to finish the setting. Wait 9 seconds before
the failsafe takes effect.
Note: If failsafe is not set, the model will hold the last position after signal is lost, thus it may fly away or cause injury.

FCC STATEMENT
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority
to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.

FrSky is continuously adding features and improvements to our products. To get the most from your product, please check
the download section of the FrSky website www.frsky-rc.com for the latest update firmware and manuals

You might also like