Scribd
Upload
35 views

Chapter 4 Structures (1)

Uploaded by

habamueneyemequanint
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
35 views

Chapter 4 Structures (1)

Uploaded by

habamueneyemequanint
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 37

Chapter 4

Structures
Engineering Mechanics I
Content
4. ANALYSIS OF STRUCTURES
4.1. Introduction
4.2. Trusses
4.2.1. Plane Trusses
- Method of Joints
- Method of Sections
4.2.2. Space Trusses
4.3. Pin-ended Multi-Force Structures
4.3.1. Frames
4.3.2. Simple Machines
4.1 Introduction
• This chapter focus on determination of the
force internal to the structure.
• An engineering structure is any connected
system of members built to support or
transfer forces and to safely withstand the
loads applied to it.
• Internal forces acting on trusses, frames and
machines will be analyzed.
4.2 Trusses

4.2.1. Plane Trusses


• A truss is a framework composed of
members joined at their ends to form a
rigid structure.
• When the members of the truss lie
essentially in a single plane, the truss is
known as a plane truss
• Bridges, roof supports, derricks are
common examples of trusses
Roof Truss
Commonly Used Roof Trusses
Tokyo Gate Bridge, a 2.6km long truss bridge
Commonly Used Bridge Trusses
Simple Truss
• The basic element of a plane truss is the
triangle.
• Three bars joined by a pin at their end forms
a rigid frame

• Structures built from a basic triangle are


known are simple truss.
Simple Truss
Assumptions in the force analysis of
simple trusses
• All members are assumed to be two-
force members.

• The two forces are applied at the ends of the


member.
• The forces are necessarily equal, opposite
and collinear.
Simple Truss
Assumptions in the force analysis of simple trusses
• The members may be in tension or compression.
• The tension or compression acting on the cut
section is same for all sections.
• If weight must be taken to account, replace the
weight W of the member by two forces each W/2,
acting at each end
• Connection is pin joint
• All external forces are applied at the pin
connections.
Force analysis of plane
trusses
• Two methods for the force analysis of
simple trusses will be given.
• The external reactions are usually
determined first from the equilibrium
equations applied to the truss as a whole
before the force analysis of the remainder
of the truss.
Method Of Joint
• This method consists of satisfying the
conditions of equilibrium for the forces
acting on the connecting pin of each joint.
σ𝑭 = 𝟎
• The method deals with the equilibrium of
concurrent forces, and hence only two
independent equilibrium equations are
involved
• We begin the analysis with any joint where
at least one known load exists and where not
more than two unknown forces are present
- Taking free body diagram of a
joint, tension will always be
Print master indicated by an arrow away
from the pin, and compression
will always be indicated by an
arrow toward the pin.

External Equilibrium conditions


Reactions are must be satisfied
calculated first at each joint
Example 1
• Compute the force in each member
of the loaded cantilever truss by the
method of joints.
solution
If it were not desired to calculate the external reactions
at D and E, the analysis for a cantilever truss could
begin with the joint at the loaded end. However, this
truss will be analyzed completely, so the first step will
be to compute the external forces at D and E from the
free-body diagram of the truss as a whole
Cont..
• Draw free-body diagrams showing the forces
acting on each of the connecting pins. The
correctness of the assigned directions of the
forces is verified when each joint is considered in
sequence
Joint A:
ΣFy=0 AB sin 60- 30=0⇒AB=34.6 kN T
ΣFx=0 AC- (34.6)cos 60=0⇒AC=17.32 kN C
Joint B must be analyzed next, since there are more
than two unknown forces on joint C
. Joint B
ΣFy=0 BCsin60 -ABsin60=0⇒BCsin60-(34.6)sin60=0⇒ BC=
34.6 kN C
ΣFx=0 BD- AB cos60 –BC cos60=0⇒ BD- 34.6 cos60 –34.6
cos60=0⇒BD=34.6 kN T
Joint C
ΣFy=0 CDsin60-BCsin60-20=0⇒ CDsin60-34.6sin60-20=0⇒
CD=57.7 kN T
ΣFx=0⇒CE-AC-BCcos60-CDcos60=0⇒
CE-17.32-(34.6)cos60-(57.7) cos60=0
⇒CE= 63.5 kN C
Joint E
ΣFy=0 DEsin60-10=0⇒DE= 11.55 kN C
Method of Section
• Takes advantages of the third or moment
equation of equilibrium.
• This method has the basic advantage that the
force in almost any desired member may be
found directly from an analysis of a section
which has cut that member
• Not more than three members whose forces
are unknown may be cut
Method of Section
Important Considerations
• Entire portion of the truss is considered a single
body in equilibrium. Thus, the forces in
members internal to the section are not
involved in the analysis.
• The section is preferably passed through the
members and not the joints.
• Methods of sections and joints can be
combined for an efficient solution.
• The moment equations are used to great
advantage in the method of sections. One
should choose a moment center, either on or off
the section, through which as many unknown
forces as possible pass.
Example 2
Determine the force in member GC of the
truss. If P1 = 0KN and P2 = 1000KN and
a = b = 10m

Solution: 1st determine the external reactions


෍ 𝐹𝑦 = 0; 𝐴𝑦 + 𝐷𝑦 = 1000𝐾𝑁

෍ 𝑀𝐴 = 0 → 𝐷𝑦 30 − 1000 20 = 0 → 𝐷𝑦 = 667𝐾𝑁

𝐴𝑦 = 333𝐾𝑁
Solution

𝐹𝐺𝐸
෍ 𝑀𝐺 = 0

𝐹𝐺𝐶 −𝐴𝑦 10 + 𝐹𝐵𝐶 (10) = 0

333 10 − 𝐹𝐵𝐶 (10) = 0


𝐹𝐵𝐶
𝐹𝐵𝐶 = 333𝐾𝑁

෍ 𝑀𝐸 = 0

𝐴𝑦 20 − 𝐹𝐺𝑐 sin 45 10 −𝐹𝐵𝐶 (10) = 0

333 20 − 𝐹𝐺𝑐 sin 45 10 − 333 (10) = 0

𝐹𝐺𝐶 = 471𝐾𝑁
4.3 Frames and Machines
• A structure is called a frame or machine if at
least one of its individual members is a multi
force member.
• A multi force member is defined as one with
three or more forces acting on it or one with
two or more forces and one or more couples
acting on it.
• Because frames and machines contain mutli
force members, the forces in these members
in general will not be in the direction of the
members.
4.3 Frames and Machines
• Frames are structures which are designed to
support applied loads and are usually fixed
in position.
• Machines are structures which contain
moving parts and are designed to transmit
forces or couples from input values to output
values.
• This chapter unlike the previous chapter,
which deals with equilibrium of single rigid
body, concentrate on equilibrium of
interconnected rigid bodies.
Frames and Machines
• The forces acting on each member of a
connected system are found by isolating the
member with a free-body diagram and
applying the established equations of
equilibrium.
• The principle of action and reaction must be
carefully observed when we represent the
forces of interaction on the separate free-
body diagrams.
Cont..
• If the frame or machine constitutes a rigid
unit by itself when removed from its supports,
the analysis is best begun by establishing all
the forces external to the structure considered
as a single rigid body
Cont..
• If the structure is not a rigid unit by itself but
depends on its external supports for rigidity,
as in the figure below, then the calculation of
the external support reactions cannot be
completed until the structure is dismembered
and the individual parts are analyzed
Cont..
• It is not always possible to assign every force
or its components in the proper sense
• In any event it is absolutely necessary that a
force be consistently represented on the
diagrams for interacting bodies,
Cont..
Frame analysis involves determining
I. External Reactions
II. Internal forces at the joints
machines
• Machines are usually non-rigid internally
• So we use the components of the machine
as a free-body
• Given the magnitude of P, determine the
magnitude of Q
Cont..

.
Example 3
The frame supports the 400-kg load in the manner
shown. Neglect the weights of the members
compared with the forces induced by the load and
compute the horizontal and vertical components of
all forces acting on each of the members.
Cont..

• .
34

Solution: continued…

The solution may proceed by use of a moment


equation about B or E for
member BF, followed by the two force
equations. Thus,

Positive numerical values of the unknowns mean that we assumed their directions correctly on the free-
body diagrams. The value of Cx = Ex = 13.08 kN obtained by inspection of the free-body diagram of CE is
now entered onto the diagram for AD, along with the values of Bx and By just determined. The equations
of equilibrium may now be applied to member AD as a check, since all the forces acting on it have already
been computed. The equations give

SIMON G.
Example 4
• Neglect the weight of the frame and compute the
forces acting on all of its members.
Cont..
• . Next we dismember the frame and draw the free-
body diagram of each part
Cont..

• .

You might also like