Brocade Fabric OS v6.3.

1c
Release Notes v1.0

May 19, 2010

Document History
Document Title Summary of Changes Publication Date

Brocade Fabric OS v6.3.1c Release Notes v1.0 Initial release May 19, 2010
 © 2010 Brocade Communications Systems, Inc. All Rights Reserved.

Brocade, the B-wing symbol, BigIron, DCX, Fabric OS, FastIron, IronView, NetIron, SAN Health, ServerIron,
and TurboIron are registered trademarks, and Brocade Assurance, DCFM, Extraordinary Networks, and
Brocade NET Health are trademarks of Brocade Communications Systems, Inc., in the United States and/or
in other countries. Other brands, products, or service names mentioned are or may be trademarks or
service marks of their respective owners.

Notice: This document is for informational purposes only and does not set forth any warranty, expressed or
implied, concerning any equipment, equipment feature, or service offered or to be offered by Brocade.
Brocade reserves the right to make changes to this document at any time, without notice, and assumes no
responsibility for its use. This informational document describes features that may not be currently
available. Contact a Brocade sales office for information on feature and product availability. Export of
technical data contained in this document may require an export license from the United States
government.

Notice: The product described by this document may contain “open source” software covered by the GNU
General Public License or other open source license agreements. To find-out which open source software is
included in Brocade products, view the licensing terms applicable to the open source software, and obtain
a copy of the programming source code, please visit http://www.brocade.com/support/oscd.

Export of technical data contained in this document may require an export license from the United States
Government

Fabric OS v6.3.1c Release Notes v1.0 Page 2 of 84

Contents
Overview ...................................................................................................................................................... 4
Additional Hardware Platform Support ..................................................................................................... 4
New Enhancements .................................................................................................................................... 4
Optionally Licensed Software .................................................................................................................... 4
Temporary License Support .................................................................................................................................... 6
Universal Temporary License Support .................................................................................................................... 7
Previously Licensed Software Now Part of Base FOS ............................................................................................ 7
Supported Switches .................................................................................................................................... 7
Standards Compliance ............................................................................................................................... 8
Technical Support ....................................................................................................................................... 8
FOS Migration Considerations .................................................................................................................. 9
TSBs - Critical Issues to Consider Prior to Installing This FOS Release .............................................................. 10
TSB Issues Outstanding in FOS v6.3.1c ............................................................................................................... 10
TSB Issues Resolved in FOS v6.3.1c .................................................................................................................... 10
Recommended Migration Paths to FOS v6.3.1c.................................................................................................. 10
FOS Upgrades and Downgrades ........................................................................................................................... 10
Important Notes ......................................................................................................................................... 11
DCFM Compatibility ............................................................................................................................................... 11
EFCM and Fabric Manager Compatibility ............................................................................................................. 12
WebTools Compatibility ......................................................................................................................................... 12
Fabric OS Compatibility ......................................................................................................................................... 12
SAS Version Requirements for FA4-18 and Brocade 7600: ............................................................................... 19
Scalability ............................................................................................................................................................... 19
Other Important Notes and Recommendations ................................................................................................... 19
Documentation Updates ........................................................................................................................... 31
Brocade Access Gateway Administrator’s Guide (Publication Number 53-1001760-01) ................................ 31
Defects ....................................................................................................................................................... 32
Closed with Code Change in Fabric OS v6.3.1c ................................................................................................... 32
Closed with Code Change in Fabric OS v6.3.1b................................................................................................... 32
Closed with Code Change in Fabric OS v6.3.1a................................................................................................... 41
Closed with Code Change in Fabric OS v6.3.1 ..................................................................................................... 45
Closed with Code Change in Fabric OS v6.3.0d................................................................................................... 61
Closed with Code Change in Fabric OS v6.3.0c ................................................................................................... 64
Closed with Code Change in Fabric OS v6.3.0b................................................................................................... 69
Closed with Code Change in Fabric OS v6.3.0a................................................................................................... 78

Fabric OS v6.3.1c Release Notes v1.0 Page 3 of 84

Overview
Fabric OS (FOS) v6.3.1c is a patch release based on FOS v6.3.1. All hardware platforms and features
supported in FOS v6.3.1 are also supported in v6.3.1c. This release also contains changes and fixes for some
important defects including those from the FOS v6.3.1, v6.3.1a and v6.3.1b maintenance and patch releases,
as well as FOS v6.3.0a, b, c, and d patch releases.
The defect fixing in this release is listed in the defect tables at the end of this document.

Additional Hardware Platform Support

Brocade Fabric OS v6.3.1 supports all platforms supported with FOS v6.3.0 plus the following:
• 5460 (embedded switch)
• 5470 (embedded switch)
• NC-5480 (embedded switch)
• Brocade VA-40FC

New Enhancements
FOS v6.3.1 supports the following new functionality:
- IPSec support on the Brocade 7800
- VLAN tagging (802.1p) support on 7800/FX8-24 FCIP links
- 10 to 1G tunnel/circuit connectivity configuration on FX8-24
o Allows connection between 10GbE ports on an FX8-24 and 1GbE ports on a 7800 or FX8-24
through an Ethernet switch
- FIP (FCoE Initialization Protocol) v1.0 (FC-BB5v2.0 - was included in FOS v6.3.0b and later)
- Port Beaconing (also supported in FOS v6.2.1)
- Automatic assignment of slot-based licenses
- Access Gateway support on the Brocade 8000 (if using DCFM, v10.4 or later is required)

Optionally Licensed Software

Optionally licensed features in Fabric OS v6.3.1 include:
• Brocade Ports on Demand — Allows customers to instantly scale the fabric by provisioning additional
ports via license key upgrade (applies to select models of switches).
• Brocade Extended Fabrics — Provides greater than 10km of switched fabric connectivity at full
bandwidth over long distances (depending on platform this can be up to 3000km).
• Brocade ISL Trunking — Provides the ability to aggregate multiple physical links into one logical link for
enhanced network performance and fault tolerance. Also includes Access Gateway ISL Trunking on
those products that support Access Gateway deployment.
• Brocade Advanced Performance Monitoring — Enables performance monitoring of networked storage
resources. This license includes the TopTalkers feature.
• High Performance Extension over FCIP/FC (formerly known as “FC-IP Services”) (For the FR4-18i blade
and Brocade 7500) — This license key also includes the FC-FastWrite feature and IPsec capabilities.
• Brocade Accelerator for FICON – This license enables unique FICON emulation support for IBM’s
Global Mirror (formerly XRC) application (including Hitachi Data Systems HXRC and EMC’s XRC) as well
as Tape Pipelining for all FICON tape and virtual tape systems to significantly improve XRC and tape

Fabric OS v6.3.1c Release Notes v1.0 Page 4 of 84

 backup/recovery performance over virtually unlimited distance for 7500, upgraded 7500E and FR4-
18i.
• Brocade Fabric Watch — Monitors mission-critical switch operations. Fabric Watch also includes Port
Fencing capabilities.
• FICON Management Server — Also known as “CUP” (Control Unit Port), enables host-control of
switches in Mainframe environments.
• ICL 16-
16-link, or Inter Chassis Links – This license provides dedicated high-bandwidth links between two
Brocade DCX chassis, without consuming valuable front-end 8Gb ports. Each chassis must have the
16-link ICL license installed in order to enable the full 16-link ICL connections. (Available on the DCX
only, previously known as simply the “ICL License” for DCX).
• ICL 8-
8-Link, or Inter Chassis Links – This license activates all eight links on ICL ports on a DCX-4S
chassis or half of the ICL bandwidth for each ICL port on the DCX platform by enabling only eight links
out of the sixteen links available. This allows users to purchase half the bandwidth of DCX ICL ports
initially and upgrade with an additional 8-link license to utilize the full ICL bandwidth at a later time.
This license is also useful for environments that wish to create ICL connections between a DCX and a
DCX-4S, the latter of which cannot support more than 8 links on an ICL port. Available on the DCX-4S
and DCX platforms only (This license replaces the original ICL license for the DCX-4S and is new for the
DCX).
• Enhanced Group Management — This license, available only on the DCX, DCX-4S and other 8G
platforms, enables full management of the device in a datacenter fabric with deeper element
management functionality and greater management task aggregation throughout the environment.
This license is used in conjunction with Brocade’s Data Center Fabric Manager (DCFM) application
software.
• Adaptive Networking — Adaptive Networking provides a rich framework of capability allowing a user to
ensure high priority connections obtain the network resources necessary for optimum performance,
even in congested environments. The QoS SID/DID Prioritization and Ingress Rate Limiting features
are the first components of this license, and are fully available on all 8G platforms.
• Integrated Routing — This license allows ports in a DCX, DCX-4S, 5300, 5100, 7800 or Brocade
Encryption Switch to be configured as EX_Ports or VEX_Ports supporting Fibre Channel Routing. This
eliminates the need to add an FR4-18i blade or use the 7500 for FCR purposes, and also provides
double the bandwidth for each FCR connection (when connected to another 8G-capable port).
• 7500E Upgrade (For the Brocade 7500E only) — This license allows customers to upgrade a 4-port (2
FC ports and 2 GE ports) 7500E base to a full 18-port (16 FC ports and 2 GE ports) 7500
configuration and feature capability. The upgraded 7500E includes the complete High Performance
Extension license feature set.
• Encryption Performance Upgrade — This license provides additional encryption processing power. For
the Brocade Encryption Switch or a DCX/DCX-4S, the Encryption Performance License can be installed
to enable full encryption processing power on the BES or on all FS8-18 blades installed in the
DCX/DCX-4S chassis.
• DataFort Compatibility — This license is required on the Brocade Encryption Switch/DCX/DCX-4S with
FS8-18 blade(s) to read & decrypt NetApp DataFort-encrypted disk and tape LUNs. DataFort
Compatibility License is also required on the Brocade Encryption Switch or DCX/DCX-4S Backbone
with FS8-18 Encryption Blade(s) installed to write & encrypt the disk and tape LUNs in NetApp
DataFort Mode (Metadata & Encryption Algorithm) so that DataFort can read & decrypt these LUNs.
DataFort Mode tape encryption and compression is supported beginning with the FOS v6.2.0 release.
Availability of the DataFort Compatibility license is limited; contact your vendor for details.
• Server Application Optimization — When deployed with Brocade Server Adapters, this license optimizes
overall application performance for physical servers and virtual machines by extending virtual
channels to the server infrastructure. Application specific traffic flows can be configured, prioritized,
and optimized throughout the entire data center infrastructure. This license is not supported on the

Fabric OS v6.3.1c Release Notes v1.0 Page 5 of 84

 Brocade 8000.
• FCoE — This license enables Fibre Channel over Ethernet (FCoE) functionality on the Brocade 8000.
Without the FCoE license, the Brocade 8000 is a pure L2 Ethernet switch and will not allow FCoE
bridging or FCF capabilities. This license should always be installed with the 8000 FC Ports on
Demand license.
• 8000 FC Ports on Demand — This new license enables all eight FC ports on the Brocade 8000.
(IMPORTANT
IMPORTANT NOTE: Most Brocade 8000 units shipped with FOS v6.1.2_CEE1 did not ship with this
license and need to have it installed prior to upgrading to FOS v6.3.1. Failure to do so will result in
disabling of FC ports following the upgrade. Please contact Brocade to obtain this license key). This
license should always be installed with the FCoE license.
• 7800 Port Upgrade — This new license allows a Brocade 7800 to enable 16 FC ports (instead of the
base four ports) and six GbE ports (instead of the base two ports). This license is also required to
enable additional FCIP tunnels and also for advanced capabilities like tape read/write pipelining. The
Brocade 7800 must have the Port Upgrade license installed to add FICON Management Sever (CUP) or
Advanced Accelerator for FICON.
• Advanced Extension – This new license enables two advanced extension features: FCIP Trunking and
Adaptive Rate Limiting. The FCIP Trunking feature allows multiple IP source and destination address
pairs (defined as FCIP Circuits) via multiple 1GbE or 10GbE interfaces to provide a high bandwidth
FCIP tunnel and failover resiliency. In addition, each FCIP circuit supports four QoS classes (Class-F,
Hi, Medium and Low Priority), each as a TCP connection. The Adaptive Rate Limiting feature provides
a minimum bandwidth guarantee for each tunnel with full utilization of the available network
bandwidth without impacting throughput performance under high traffic load. This license is available
on the 7800 and the DCX/DCX-4S for the FX8-24 on an individual slot basis.
• 10GbE FCIP – This new license enables the two 10GbE ports on the FX8-24. With this license, two
additional operating modes (in addition to 10 1GbE ports mode) can be selected:
o 10 1GbE ports and 1 10GbE port, or
o 2 10GbE ports
This license is available on the DCX/DCX-4S for the FX8-24 on an individual slot basis.

• Advanced FICON Acceleration – This new licensed feature uses specialized data management
techniques and automated intelligence to accelerate FICON tape read and write and IBM Global Mirror
data replication operations over distance, while maintaining the integrity of command and
acknowledgement sequences. This license is available on the 7800 and the DCX/DCX-4S for the FX8-
24 on an individual slot basis.
Some models offer bundles that include 2 or more optionally licensed features. These bundles are defined for
each unique product, and are outside the scope of this release note document.

Temporary License Support

The following licenses are available for 45-day temporary use, with a maximum of two temporary licenses
per feature and per switch (90 days maximum):
• Fabric (E_Port) license
• Extended Fabric license
• Trunking license
• High Performance Extension license
• Advanced Performance Monitoring license
• Adaptive Networking license
• Fabric Watch license
• Integrated Routing license

Fabric OS v6.3.1c Release Notes v1.0 Page 6 of 84

 • Server Application Optimization(support as a temporary license is new in FOS v6.3)
• Advanced Extension license (support is new in FOS v6.3)
• Advanced FICON Acceleration license (support is new in FOS v6.3)
• 10GbE FCIP license (support is new in FOS v6.3)
Note: Temporary Licenses for features available on a per slot basis enable the feature for any and all slots in
the chassis.

Universal Temporary License Support

The following list of licenses are available as Universal Temporary licenses, meaning the same license key
can be installed on any switch running FOS v6.3 or later that supports the specific feature. Universal
Temporary license keys can only be installed once on a particular switch, but can be applied to as many
switches as desired. Temporary use duration (the length of time the feature will be enabled on a switch) is
provided with the license key. All Universal Temporary license keys have an expiration date upon which
the license can no longer be installed on any unit.
• Fabric (E_Port) license
• Extended Fabric license
• Trunking license
• High Performance Extension license
• Advanced Performance Monitoring license
• Adaptive Networking license
• Fabric Watch license
• Integrated Routing license
• Server Application Optimization
• Advanced Extension license
• Advanced FICON Acceleration license
• 10GbE license
• FICON Management Server (CUP) license

Previously Licensed Software Now Part of Base FOS

The following capabilities are included as part of the base FOS capability and no additional purchase or
licensing is necessary:
• Advanced Zoning and WebTools licenses are no longer necessary beginning with FOS v6.1. These
features are automatically enabled on all products running FOS v6.1 or later.

Supported
Supported Switches
Fabric OS v6.3.1 supports the Brocade 300, 5410/5480/5424/5450/5460/5470/NC-5480, 4100, 4900,
5000, 5100, 5300, VA-40FC, 7500/7500E, 7600, 48000, Brocade Encryption Switch (BES), DCX/DCX-4S,
8000, and the new 7800. All supported products are qualified for Native Connectivity in interopmodes 2 and 3
for deployment in M-EOS fabrics with the exception of the Brocade 4100 and 8000.

Access Gateway mode is also supported by Fabric OS v6.3.1, and is supported on the following switches: the
Brocade 300, 5100, VA-40FC, 8000*, 5480, 5450, 5460, 5470, NC-5480 and M5424.

* If using DCFM to manage a fabric with a Brocade 8000 in Access Gateway mode, version 10.4 or later is
required

Note that FOS v6.3 does NOT support the following platforms and cannot be loaded on them, though these
switches may participate in the same fabric as other switches using FOS v6.3:
• Brocade 200E
• All 4G embedded switches, including the 4012, 4016, 4018, 4020, 4024, 4424

Fabric OS v6.3.1c Release Notes v1.0 Page 7 of 84

Please refer to the Supported Products and FOS Interoperability table for the versions of FOS code that must
be used on these platforms to interoperate with FOS v6.3. The above noted 4G platforms will continue to be
supported by FOS v6.2.x.

Standards Compliance
This software conforms to the Fibre Channel Standards in a manner consistent with accepted
engineering practices and procedures. In certain cases, Brocade might add proprietary supplemental
functions to those specified in the standards. For a list of FC standards conformance, visit the
following Brocade Web site: http://www.brocade.com/sanstandards

The Brocade 8000 and FCOE10-24 blade conform to the following Ethernet standards:
• IEEE 802.1D Spanning Tree Protocol
• IEEE 802.1s Multiple Spanning Tree
• IEEE 802.1w Rapid reconfiguration of Spanning Tree Protocol
• IEEE 802.3ad Link Aggregation with LACP
• IEEE 802.3ae 10G Ethernet
• IEEE 802.1Q VLAN Tagging
• IEEE 802.1p Class of Service Prioritization and Tagging
• IEEE 802.1v VLAN Classification by Protocol and Port
• IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
• IEEE 802.3x Flow Control (Pause Frames)

The following draft versions of the Converged Enhanced Ethernet (CEE) and Fibre Channel over Ethernet (FCoE)
Standards are also supported on the Brocade 8000 and FCOE10-24 blade:
• IEEE 802.1Qbb Priority-based Flow Control
• IEEE 802.1Qaz Enhanced Transmission Selection
• IEEE 802.1 DCB Capability Exchange Protocol (Proposed under the DCB Task Group of
IEEE 802.1 Working Group)
• FC-BB-5 FCoE (Rev 2.0)

Technical Support
Contact your switch supplier for hardware, firmware, and software support, including product repairs and part
ordering. To expedite your call, have the following information immediately available:
1. General Information
• Technical Support contract number, if applicable
• Switch model
• Switch operating system version
• Error numbers and messages received
• supportSave command output
• Detailed description of the problem, including the switch or fabric behavior immediately following
the problem, and specific questions
• Description of any troubleshooting steps already performed and the results
• Serial console and Telnet session logs
• Syslog message logs

Fabric OS v6.3.1c Release Notes v1.0 Page 8 of 84

 2. Switch Serial Number
The switch serial number is provided on the serial number label, examples of which are shown here:

FT00X0054E9

The serial number label is located as follows:

• Brocade 4100, 4900, and 7500/7500E — On the switch ID pull-out tab located inside the chassis
on the port side on the left
• Brocade Encryption Switch, VA-40FC, 300, 5000, 5100, and 5300 — On the switch ID pull-out tab
located on the bottom of the port side of the switch
• Brocade 7600 — On the bottom of the chassis
• Brocade 7800 — On the pull-out tab on the front left side of the chassis underneath the serial
console and Ethernet connection and on the bottom of the switch in a well on the left side
underneath (looking from front)
• Brocade 8000 — On the switch ID pullout tab located inside the chassis on the port side on the
left and also on the bottom of the chassis.
• Brocade 48000 — Inside the chassis next to the power supply bays
• Brocade DCX — Bottom right of the port side
• Brocade DCX-4S — Back, upper left under the power supply
3. World Wide Name (WWN)
When the Virtual Fabric feature is enabled on a switch, each logical switch has a unique
switch WWN. Use the wwn command to display the switch WWN.
If you cannot use the wwn command because the switch is inoperable, you can get the
primary WWN from the same place as the serial number, except for the Brocade DCX/DCX-4S.
For the Brocade DCX, access the numbers on the WWN cards by removing the Brocade logo
plate at the top of the non-port side. The WWN is printed on the LED side of both cards.
4. License Identifier (License ID)
There is only one License Identifier associated with a physical switch or director/backbone
chassis. This License Identifier is required as part of the ordering process for new FOS
licenses.
Use the licenseId command to display the License Identifier.

FOS Migration Considerations

This section contains important details to consider before migrating to or from this FOS release.

Fabric OS v6.3.1c Release Notes v1.0 Page 9 of 84

 TSBs - Critical Issues to Consider Prior
Prior to Installing This FOS Release
Technical Support Bulletins (TSBs) are produced to provide detailed information about high priority
defects or issues present in FOS releases. The following sections specify all current TSBs that have
been identified as being a risk to or resolved with this specific version of Fabric OS. Please review
carefully and refer to the complete TSB for relevant issues prior to migrating to this version of code.
TSBs can be found at http://my.brocade.com under the “Technical Documentation” section of the
“documentation” tab.

TSB Issues Outstanding in FOS v6.3.1

v6.3.1c
6.3.1c
Issues in the following list of TSBs are known to be potential risks to using FOS v6.3.1c and should be
considered carefully prior to using this release of code:

TSB Summary
None There are no current TSBs outstanding for this FOS release.

TSB Issues Resolved in FOS v6.3.1

v6.3.1c
6.3.1c
Issues in the following list of TSBs are known FOS v6.3.x risks that have been resolved in FOS v6.3.1c.
Note that the issues addressed in this list of TSBs may also be resolved in other FOS releases. Refer
to the specific Release Notes for each release to verify resolution details.

TSB Summary

2010-
2010-075-
075-A When upgrading a DCX, DCX-4S or Brocade 5300 from Fabric OS v6.2.2a or lower to FOS
(Defect v6.3.1 or 6.3.0c or lower, the Compact Flash (CF) may report an access error. This will cause a
270261) reboot of the affected CP within the DCX/DCX-4S or Brocade 5300 to fail.

After performing a non-disruptive firmware upgrade from Fabric OS v6.2.x to Fabric OS v6.3.0
2010-
2010-076-
076-A through v6.3.0c or v6.3.1, the State Change Registration (SCR) value is not preserved in the
(Defect Name Server database. After this occurs, the Name Server will not transmit Registered State
284472) Change Notifications (RSCN) to the devices on those ports. If a device does not receive an
RSCN, it will not know when there is a change to the zoning configuration or device availability.

After a non-disruptive upgrade to Fabric OS v6.2.x or higher, CDR-1003 messages may be

2010-
2010-081-
081-A posted during a supportSave operation. This may occur on a Brocade 200E, 4012, 4016,
4018, 4020, 4024, 4424, 4100, 4900, 7500, 7600 or 48000.

Recommended Migration Paths to FOS v6.3.1

v6.3.1c
6.3.1c
Migrating from FOS v6.1.x
For units currently operating at FOS v6.1.x, Brocade recommends using FOS v6.2.2b as a migration
path to v6.3.1c in order to reduce risk of exposure to known issues at the v6.2.x code levels.
Migrating from FOS v6.2.x
For units currently operating at FOS v6.2.x, there are no special steps required to migrate to FOS
v6.3.1c.

FOS Upgrades and Downgrades

Upgrading to Fabric OS v6.3.1 is only allowed from Fabric OS v6.2.0 or later. This policy to support
only one-level migration, which began with FOS v6.0.0, provides more reliable and robust migrations
for customers. By having fewer major changes in internal databases, configurations, and subsystems,
the system is able to perform the upgrade more efficiently, taking less time and ensuring a truly
seamless and non-disruptive process for the fabric. The one-release migration policy also reduces the

Fabric OS v6.3.1c Release Notes v1.0 Page 10 of 84

 large number of upgrade/downgrade permutations that must be tested, allowing Brocade to spend
more effort ensuring the supported migration paths are thoroughly and completely verified.

Most products supported by Fabric OS v6.2.X or v6.1.2_CEEx can be upgraded to Fabric OS v6.3. The
following is a list of products that can be upgraded to Fabric OS v6.3:

• 5424/5410/5480, 4100, 4900, 5000, 300, 5100, 5300, 7500/7500E, 7600, 8000,
48000, BES, DCX-4S and DCX.

Switches using Integrated Routing and operating with FOS v6.2.2x may not be upgraded directly to
FOS 6.3.0/v6.3.0a/v6.3.0b. Units operating with IR and FOS v6.2.2x should be upgraded to FOS
v6.3.0c, v6.3.1 or later firmware or first downgraded to a release prior to v6.2.2.

FOS does not support concurrent FC Routing (EX_Ports) and TopTalkers features.

If there are multiple node EGs (encryption groups) in a fabric, please complete firmwaredownload on
one node at a time before downloading on another node.

The Brocade 8000 does not support non-disruptive hot code loads (HCL). Upgrading the Brocade
8000 from FOS v6.1.2_cee1 to FOS v6.3 or from FOS 6.3 to a later FOS version will be disruptive to
the IO through the switch.

A code load of DCX or DCX-4s with one or more FCOE10-24 blades from FOS 6.3 to another version
will disrupt traffic through the blade.

When upgrading a Brocade 8000 from FOS v6.1.2_CEE or v6.1.2_CEE1 to v6.3, verify that the unit
has both the FCoE and FC POD licenses installed. Units missing these licenses that are upgraded to
FOS v6.3 will lose functionality following a restart or disabling of ports. Note that when the FC POD
license is installed on a unit with FOS v6.1.2, the licenseShow output will indicate that the license is
“not applicable on this platform.” This message can be ignored and will not appear once the unit has
been upgraded to v6.3.

If a switch with FOS v6.2 in FIPS (Federal Information Processing Standards) mode with only LDAP
authentication support is upgraded to v6.3, login will fail. A switch with v6.2 in FIPS mode must have
both LDAP and local authentication configured before upgrading to v6.3. Once the switch is fully
operational, the user can login to the switch and import the certificate again. If the switch is not in
FIPS mode, users can login to the switch with LDAP after upgrading to v6.3 and then import the
certificate.

Important
Important Notes
This section contains information that you should consider before you use this Fabric OS
release.

DCFM Compatibility
FOS v6.3.1 is compatible with Brocade’s Data Center Fabric Manager (DCFM) v10.3.x management
software. DCFM is a comprehensive SAN management application that enables end-to-end
management of Brocade Data Center Fabrics. It is the next-generation successor product to existing
Brocade management products, including Brocade Fabric Manager (FM) and Brocade Enterprise
Fabric Connectivity Manager (EFCM).

DCFM 10.3 is available in three editions:

• DCFM Professional: a fabric management application that is ideally suited for small-size
businesses that need a lightweight management product to manage their smaller fabrics. It
manages one FOS fabric at a time, up to 1,000 switch ports, and provides support for Brocade FC

Fabric OS v6.3.1c Release Notes v1.0 Page 11 of 84

 switches, Brocade HBAs / CNAs, and Fibre Channel over Ethernet (FCoE) / Converged Enhanced
Ethernet (CEE) switches
• DCFM Professional Plus: a SAN management application designed for medium-size businesses for
managing up to 4 physical fabrics (FOS, M-EOS and Mixed fabrics) up to 2,560 switch ports. It
supports Brocade director products (DCX-4S, 48Ks, etc.), FC switches, Fibre Channel Over IP
(FCIP) switches, Fibre Channel Routing (FCR) switches/ Integrated Routing (IR) capabilities, Fibre
Channel over Ethernet (FCoE) / Converged Enhanced Ethernet (CEE) switches, and Brocade HBAs
/ CNAs. Enterprise-class customers looking to manage departmental SANs can consider
deploying this product as well
• DCFM Enterprise: a SAN management application designed for enterprise-class customers for
managing up to 24 physical fabrics and up to 9,000 switch ports. DCFM Enterprise supports all
the hardware platforms and features that DCFM Professional Plus supports, and also adds
support for the Brocade DCX Director product, and Fiber Connectivity (FICON) capabilities

Existing EFCM v9.6.x/9.7.x and FM v5.4/5.5 customers are provided an easy migration path to DCFM
Enterprise.
DCFM Management Considerations
Considerations
• When managing a Brocade 8000 in Access Gateway Mode, DCFM 10.4.0 or later is required. Use
of earlier DCFM releases will prevent management of zoning on the fabric.

• DCFM v10.3.x and earlier cannot manage FOS switches or fabrics using Administrative Domains
(ADs). Environments using ADs must use DCFM v10.4 or later or use the CLI or WebTools for
management.

EFCM and Fabric Manager Compatibility

With the introduction of DCFM, both EFCM and Fabric Manager (FM) have been put into sustaining
mode. Consequently, neither EFCM nor FM are qualified or supported for management of switches
operating with FOS v6.3 firmware. Very basic evaluation has shown that there are significant
compatibility issues between FM and FOS v6.3, including (but not limited to) compromised
functionality in the zoning dialog and performance graphs, port enabling/disabling, and the FICON
wizard.

WebTools Compatibility
• FOS v6.3 is supported with JRE 1.6.0 Update 13.
• If the JRE v1.6.0 version is not at Update 13, the DCFM server / client and B-model Element
Manager (Web Tools) Crashes on launch
• WebTools Tunnel and TCP graphs only support Tooltips for the first enabled TCP connection graph.

Fabric OS Compatibility
The following table lists the earliest versions of Brocade software supported in this release, that is, the
earliest supported software versions that interoperate. Brocade recommends using the latest
software versions to get the greatest benefit from the SAN.
When using the Virtual Fabrics feature, it is highly recommended that all switches participating in a
fabric with a logical switch use the latest firmware available for those switches. All switches must be
operating at minimum firmware levels noted in the FOS Interoperability table below.
When using any of Brocade’s encryption platforms (Brocade Encryption Switch or Brocade FS8-18
blade in a DCX or DCX-4S) it is required that switches attached to hosts and targets or those that are
part of the encryption flow be operating with minimum specified levels:
• 2Gb/4Gb platforms must operate with FOS v5.3.1b or later

Fabric OS v6.3.1c Release Notes v1.0 Page 12 of 84

 • 4Gb/8Gb platforms must operate with FOS v6.1.0e, v6.1.1 or later (4Gb platforms may use
v5.3.1b but are recommended to use the v6.x versions)
• M-EOS platforms must operate with M-EOS v9.8.0 or later for McDATA Fabric Mode
(interopmode 2) or M-EOS 9.9.0 or later for Open Fabric Mode environments (interopmode 3)
For a list of the effective end-of-life dates for all versions of Fabric OS, visit the following Brocade Web
site:
http://www.brocade.com/support/end_of_life.jsp

Supported Products and FOS Interoperability

Brocade 2000-series switches Not supported, end of support
(December 2007)
Brocade 3200, 3800 Not supported.
Brocade 3000 v3.2.1c 1 6 7
Silkworm 3016, 3250, 3850 and Brocade 3900, 4100, 4900, v5.3.2 (2G and 4G platforms) and
24000, 7500, 7500E, 5000, 200E, 48000 v6.1.0e and later 5 (4G platforms
only)
Silkworm 12000 v5.0.x 6 7
Brocade 4012, 4016, 4018, 4020, 4024, 4424 v5.3.1b, v6.1.0e and later 5
Brocade 5410, 5480, 5424 v6.2.0
Brocade 8000 v6.1.2_CEE1 or later
Brocade 7800, DCX and DCX-4S with FCOE10-24 or FX8-24 blades v6.3.0
Brocade DCX, 300, 5100, 5300 v6.1.0e and later 5
Brocade DCX-4S v6.2.0
Brocade DCX with FS8-18 blade(s), Brocade Encryption Switch v6.1.1_enc
Brocade DCX/DCX-4S/48000 with FA4-18 blade(s), Brocade 7600 v5.2.x or later (DCX requires v6.0.x
or later, DCX-4S requires 6.2.x or
later)
Mi10k, M6140, ED-6064, ES-3232, ES-4300, ES-4400, ES-4500, ES- M-EOS v9.9.5 or later 3
4700 (McDATA Fabric Mode and Open Fabric Mode) 2 4
McDATA ED-5000 32-port FC director Not Supported
Multi-
Multi-Protocol Router interop
Brocade 7420 XPath v7.4.1 8
Brocade 7500 and FR4-18i blade v5.1.0 and higher 8
McDATA SANRouters 1620 and 2640 Not Supported

Table Notes:
1All zoning and fabric operations performed in a fabric with products running older versions of FOS should
be done via interfaces to products running the latest version of FOS. This is particularly important for
Brocade 3XXX series switches that do not support zoning configuration for newer products.

Fabric OS v6.3.1c Release Notes v1.0 Page 13 of 84

 2Other M-EOS models may participate in a fabric with FOS v6.3, but may not be directly attached via E_Port
to any products running FOS v6.3. The McDATA ED-5000 director may not participate in a mixed M-
EOS/FOS fabric.
3 It is highly recommended that M-EOS products operate with the most recent version of M-EOS released
and supported for interoperability. M-EOS 9.9.5 is the only version of code that has been fully qualified for
interoperability with FOS v6.3. M-EOS 9.7.2 is the minimum version of firmware that is supported to
interoperate with FOS 6.3. For support of frame redirection in McDATA Fabric Mode (interopmode 2), M-
series products must use M-EOS v9.8 or later. For support of frame redirection in McDATA Open Fabric
Mode (interopmode 3), M-series products must use M-EOS v9.9 or later. Only the ES-4400, ES-4700,
M6140, and Mi10k may have devices directly attached that are having data encrypted or unencrypted.
4When routing to an M-EOS edge fabric using frame redirection, the M-EOS fabric must have a FOS-based
product in order to configure the frame redirection zone information in the edge fabric.
5When directly attached to a Host or Target that is part of an encryption flow.
6Products operating with FOS versions less than v5.3.1b or v6.1.0e may not participate in a logical fabric
that is using XISLs (in the base fabric).
7These platforms may not be directly attached to hosts or targets for encryption flows.
8McDATA 1620 and 2640 SANRouters should not be used with XPath or FOS-based routing (FCR) for
connections to the same edge fabric.
Fabric OS v6.3.1 software is fully qualified and supports the blades for the 48000 platform noted in the
following table:

48000 Blade Support

Support Matrix
Port blade 16, 32 and 48-port 4Gbit blades (FC4- Supported with any mix and up to 8 of each. No
16, FC4-32, FC4-48), 16, 32 and 48-port 8Gbit restrictions around intermix. The 48000 must run
blade (FC8-16, FC8-32, FC8-48), and the 6-port Fabric OS v6.0 or later to support the FC8-16 port
10G FC blade (FC10-6) blade and Fabric OS v6.1 or later to support the FC8-
32 and FC8-48 port blades.
Intelligent blade Up to a total of 4 Intelligent blades (includes iSCSI,
FCIP/FCR and Application blade), FC4-16IP, FR4-18i,
and FA4-18 respectively. See below for intermix
limitations, exceptions, and a max of each blade.
iSCSI blade (FC4-16IP) Up to a maximum of 4 blades of this type
FC-IP/FC Router blade (FR4-18i) Up to a maximum of 2 blades of this type. This can be
extended under special circumstances but must be
approved by Brocade’s Product Team. Up to 8 FR4-18i
blades can be installed if they are used only for FC
FastWrite or FCIP without routing.
Virtualization/Application Blade (FA4-18) Up to a maximum of 2 blades of this type.
Encryption Blade (FS8-18), Extension Blade (FX8- Not supported.
24), FCoE/CEE Blade (FCOE10-24)

Fabric OS v6.3.1 software is fully qualified and supports the blades for the DCX/DCX-4S noted in the following
table:

DCX/DCX
DCX/DCX-
/DCX-4S Blade Support Matrix

Fabric OS v6.3.1c Release Notes v1.0 Page 14 of 84

 DCX/DCX
DCX/DCX-
/DCX-4S Blade Support Matrix
16-, 32- and 48-port 8Gbit port blades (FC8-16, Supported with FOS v6.0 and above with any mix and
FC8-32, FC8-48) and the 6-port 10G FC blade up to 8/4 of each. No restrictions around intermix.
(FC10-6)
Intelligent blade Up to a total of 8/4 intelligent blades. See below for
maximum supported limits of each blade.
FC-IP/FC Router blade (FR4-18i) Up to a maximum of 4 blades of this type. This can be
extended under special circumstances, but must be
approved by Brocade’s Product Team. Up to 8 FR4-18i
blades can be installed in a DCX if they are used only
for FC FastWrite or FCIP without routing.
Virtualization/Application Blade (FA4-18) Up to a maximum of 4 blades of this type.
Encryption Blade (FS8-18) Up to a maximum of 4 blades of this type.
Extension Blade (FX8-24) Up to a maximum of 2 blades of this type.
FCoE/CEE Blade (FCOE10-24) Up to a maximum of 2 blades of this type. Cannot be
used in a chassis with other intelligent blades (can
only be installed concurrently with FC8-XX and/or
FC10-6 blades)
Note: the iSCSI FC4-16IP blade is not qualified for the DCX/DCX-4S.

Power Supply Requirements for Blades in 48k and DCX/DCX-

DCX/DCX-4S Chassis
Blades Type of 48K DCX/DCX-
DCX/DCX-4S DCX/DCX-
DCX/DCX-4S Comments
Blade @200-240 @110 VAC @200-240 VAC
VAC (Redundant (Redundant
(Redundant configurations) configurations)
configurations)
FC4-16, FC 4- Port Blade 2 Power 2 Power 2 Power Supplies • Distribute the Power
32, FC4-48, Supplies Supplies Supplies evenly to 2
FC8-16, FC8- different AC
32 connections for
FC10-6, FC Port 4 Power Not Supported 2 Power Supplies redundancy.
8-48 Blade Supplies
FR4-18i, Intelligent 4 Power Not Supported 2 Power Supplies
FC4-16IP*, Blade Supplies
FA4-18
FS8-18, Intelligent NA Not Supported DCX: 2 or 4 Power • For DCX with three or
FX8-24, Blade Supplies more FS8-18 Blades,
FCOE10-24 (2+2) 220VAC Power
Supplies are required
DCX-4S: 2 Power
for redundancy.
Supplies
• For DCX with one or
two FS8-18 Blades,
(2) 220VAC Power
Supplies are required
for redundancy.
• For DCX-4S, (2)
220VAC Power
Supplies provide
redundant

Fabric OS v6.3.1c Release Notes v1.0 Page 15 of 84

 Power Supply Requirements for Blades in 48k and DCX/DCX-
DCX/DCX-4S Chassis
Blades Type of 48K DCX/DCX-
DCX/DCX-4S DCX/DCX-
DCX/DCX-4S Comments
Blade @200-240 @110 VAC @200-240 VAC
VAC (Redundant (Redundant
(Redundant configurations) configurations)
configurations)
configuration with any
number of FS8-18
Blades.
• For both DCX and
DCX-4S with FX8-24
blades, (1+1) 220VAC
Power Supplies are
required for
redundancy.

*Note: the iSCSI FC4-16IP blade is not qualified for the DCX/DCX-4S.
FOS Feature Compatibility in Native Connectivity Modes
Some FOS features are not fully supported when operating in the native connectivity modes for deployment
with M-EOS based products. All Brocade models that are supported by Fabric OS v6.3.1 support both
interopmodes 2 and 3 with the exception of the Brocade 4100 and 8000 and DCX/DCX-4S with one or more
FCOE10-24 blades.
The following table specifies the support of various FOS features when operating in either interopmode 2
(McDATA Fabric Mode) or interopmode 3 (Open Fabric Mode) with Fabric OS v6.3.

FOS Features (supported in interopmode 0) FOS v6.3

IM = Interopmode IM 2 IM 3
L2 FOS Hot Code Load Yes Yes
FOS Hot Code Load with FCR Yes Yes
Zone Activation Support Yes Yes11
Traffic Isolation Zones1 Yes No
Frame Redirection (devices attached to FOS)1 Yes Yes11
Frame Redirection (devices attached to M-EOS) 1 Yes Yes11
Frame Redirection over FCR10 Yes Yes11
FCR Fabric Binding (route to M-EOS fabric with Fabric binding) 9 Yes Yes
L2 Fabric Binding Yes No*
DCC policies No No
SCC policies Yes4 No*
E/EX_Port Authentication Yes Yes
ISL Trunking (frame-level) Yes2 Yes2
Dynamic Path Selection (DPS, exchange based routing) Yes3 Yes3
Dynamic Load Sharing (DLS, port based routing) Yes Yes
Virtual Channels (VC RDY) Yes2 Yes2
FICON Management Server (Cascading) Yes No*
FICON MIHPTO Yes No*
Full Scalability (to maximum M-EOS fabric limits) Yes Yes
Adaptive Networking: QoS No No
Adaptive Networking: Ingress Rate Limiting No* No*
Advanced Performance Monitoring (APM) No* No*

Fabric OS v6.3.1c Release Notes v1.0 Page 16 of 84

 FOS Features (supported in interopmode 0) FOS v6.3
IM = Interopmode IM 2 IM 3
APM: TopTalkers No* No*
Admin Domains No No
Secure Fabric OS5 N/A N/A
Fabric Watch Yes Yes
Ports on Demand (POD) Yes Yes
NPIV Yes Yes
Timer Server function (NTP) No No
Open E_Port6 N/A N/A
Broadcast Zoning No No
FDMI No No
Remote Switch No No
Port Mirroring Yes Yes
Extended Fabrics Yes Yes7
Alias Server No No
Platform Service No No
FCIP (VE_Ports) Yes Yes
IPFC (IP over FC) Yes8 Yes8
M-EOS ALPA 0x13 configuration Yes Yes
VE to VEX Port Yes Yes
Integrated Routing9 Yes9 Yes
Domain Offset Support Yes Yes
239 Domain Support (available on Mi10k only) N/A Yes
Masterless F_PORT Trunking (AG connect to FOS switches only) Yes Yes
FC10-6-to-FC10-6 ISL Yes Yes
RASLOG Events on duplicate WWNs Yes Yes
Virtual Fabrics Yes Yes
Logical Fabric using LISLs (XISLs in Base Fabric) No No
Port Fencing Yes Yes
Bottleneck Detection Yes Yes

* indicates the feature is available but not officially tested or supported

1. Requires M-EOS 9.7 or later for redirection between devices attached to FOS switches, M-EOS 9.8 for
redirection between devices attached to M-EOS switches, M-EOS 9.9 for use in McDATA Open Fabric
Mode. Supported M-EOS platforms include M4400, M4700, M6140, and Mi10k.
2. Only allowed between FOS-based switches
3. DPS is supported outbound from FOS-based switches. (M-EOS can provide reciprocal load balancing
using OpenTrunking).
4. SCC policies only supported in conjunction with L2 Fabric Binding support
5. Not supported in FOS 6.0 or later
6. Mode 3 only qualified with M-EOS switches
7. Not on FCR
8. Only supported locally within the FOS switch
9. All routers (EX_Ports) must reside in a backbone fabric running in interopmode 0 only. Only edge fabrics
with devices imported to the backbone fabric or other edge fabrics may be operating in IM2 or IM3.
10. To support Frame Redirection to an edge M-EOS fabric, there must be at least one FOS switch in the
edge fabric to configure Frame Redirection Zones.
11. Only Frame Redirection Zones may be configured on FOS platforms and sent to fabrics operating in
McDATA Open Fabric Mode (interopmode 3). M-EOS 9.9 is required to support FR Zones in McDATA
Open Fabric Mode.

Fabric OS v6.3.1c Release Notes v1.0 Page 17 of 84

Note: FICON Cascaded CUP with M-EOS and FOS qualified only on select platforms.

Fabric OS v6.3.1c Release Notes v1.0 Page 18 of 84

SAS Version Requirements for FA4-
FA4-18 and Brocade
Brocade 7600:
SAS v3.4.0 is the supported SAS version for FOS v6.3.1.
• When upgrading from FOS v6.2 to v6.3.1 and SAS 3.3.0 to SAS 3.4.0, first upgrade FOS v6.2 to v6.3.1 and
then upgrade SAS from 3.3.0 to 3.4.0.
• When downgrading from FOS v6.3.1 to v6.2 and SAS 3.4.0 to SAS 3.3.0, first downgrade SAS from 3.4.0
to 3.3.0 and then downgrade FOS from v6.3.1 to v6.2. If the switch is downgraded to v6.2 prior to the SAS
downgrade to v3.3, the switch will fault.

Scalability
All scalability limits are subject to change. Limits may be increased once further testing has been completed,
even after the release of Fabric OS. For current scalability limits for Fabric OS, refer to the Brocade Scalability
Guidelines document, available under the Technology and Architecture Resources section at
http://www.brocade.com/compatibility

Other Important Notes and Recommendations

FX8--24)
FCIP, FCIP Trunking and High Bandwidth (Brocade 7800 and FX8
• The maximum supported MTU size for the Brocade 7800/FX8-24 is 1500 with FOS v6.3.1.
• FCIP connections are supported only between the Brocade 7800/FX8-24 and another 7800/FX8-24.
FCIP tunnels are not supported between the 7800/FX8-24 and the previous generation Brocade
7500/FR4-18i platforms.
• When additional circuits (and the network bandwidth provided by those circuits) are added to an
already active tunnel, there is a short period of time where some frame loss can occur due to the
process to re-fresh the internal FC frame routing tables in the switch. Therefore, additional circuits
should only be added during low I/O periods utilizing the FCIP Tunnel being modified. In addition, if
the circuit operation (addition/deletion) to the tunnel increases/decreases the total tunnel bandwidth,
an FCIP Tunnel (VE port) disable/enable sequence should be performed after the addition/deletion of
the circuit. This will allow the switch to adjust the internal routes to utilize the new bandwidth fully.
• Switching modes between 10G and 1G is disruptive for FCIP traffic.
• Keep alive timeout (milliseconds) - Valid range is 500ms to 7,200,000ms (inclusive). Default
value is 10000ms (10 seconds). If FICON is configured the recommended value is 1000 ms
(1 second), otherwise the recommended value is the default of 10 seconds. For impairment
networks with 100ms latency and 0.5% packet loss, keep-alive time out should be configured
as 30seconds. If the local and remote circuit configurations’ Keep Alive Timeout values do
not match, the tunnel will use the lower of the two configured values.
• Software compression (available on the 7800) modes 2 and 3 are not supported in FICON
environments; they are supported only in Open Systems environments.
• Software compression (mode 2, 3) generally gives a better compression ratio, but not the
throughput/bandwidth across all six GE ports. Software compression is recommended for low
throughput links and supports throughput up to 2Gbps across all 6 GE ports.
• In order to perform the following operations it is necessary to delete the FCIP configuration on
the affected ports first:
o Switching modes between 1G/10G/Dual
o Moving VE/GE port between logical switches
• The FX8-24 supports three different operating modes:
1) Ten 1-GbE ports mode (default)

Fabric OS v6.3.1c Release Notes v1.0 Page 19 of 84

 2) Ten 1GbE ports and one 10GbE port
3) Two 10GbE ports
Modes 2 and 3 require the slot-based 10 GbE FCIP license.
• ARL (Adaptive Rate Limiting) is not supported on 10G tunnels.
• IPv6, Diffserv and “Inband Management” are not supported on the Brocade 7800 or FX8-24.
• IPSec is not supported on the Brocade FX8-24.
• FOS v6.3 only supports up to four 1 Gig Circuits per VE/FCIP Tunnel for the 1 gig interfaces. A
VE/FCIP Tunnel created over the 10 Gig Interfaces will be limited to 10 circuits created using
IPIFs on the same 10 GbE port (and no more than 1G per circuit).
• As a recommended best practice, the VE tunnel shouldn’t be over-subscribed (e.g. 8G FC
traffic over 500Mbps tunnel). General guidelines are 2:1 subscription without compression
and 4:1 with compression.
• Non-disruptive firmware activation on FOS v6.3 will disrupt I/O traffic on FCIP links.
• Fibre Channel Routing (VEX) is not supported on the Brocade FX8-24 blade but is supported
on the Brocade 7800.
• Differences between the Brocade 7800/FX8-24 platforms and previous generation
7500/FR4-18i platforms include:
o On the 7800, the GbE port does not directly correlate to a VE port
o On the FX8-24, GbE ports 0-9 or 10GbE port 1 (xge1) correspond to VE ports 12-21,
and 10 GbE port 0 (xge0) corresponds to VE ports 22-31
o The CLI syntax for the 7800/FX8-24 varies from the 7500/FR4-18i. Please refer to
the Brocade Fabric OS Command Reference document for FOS v6.3 for details.
• Both ends of a tunnel must be identically configured for Compression, FW and Tape pipeline options.
If a mismatch exists, the tunnel will not be established and the TCP virtual connections will be
removed.
• Under Traffic Isolation Zone, configurations with fail over enabled, Non-TI zone traffic will use the
dedicated path if no other E or VE paths through the fabric exist, or if the non-dedicated paths are not
the shortest paths. (A higher bandwidth tunnel with multiple circuits will become shortest path
compared to a single tunnel).
• A VE/VEX Tunnel and E/EX FC port cannot connect to the same domain at the same time.
• The Recommended Keep Alive Timeout must be the same on tunnel/circuits on the switches on both
sides of a link.
• Brocade 7800 or FX8-24 cannot receive a ping from an external device (for example – Windows PC).
• Latency measurements supported on FCIP Tunnels (Tested limit under FOS v6.3.1):
o 1GbE - 200ms round trip time and 1% Loss
o 10GbE – 50ms round trip and 0.1% Loss
• Brocade 7800 supports Optical and Copper Media types on GE0 and GE1 interfaces. Copper Media
type is default on GE0/GE1 ports and does not support auto-sense functions.
• When inserting a 4G SFP in GE ports of an FX8-24 blade or 7800 switch, users may occasionally see
one of the following:
o “No_Light” or “Unknown” for GE ports in switchshow output. Removing and re-inserting the
optic should correct this indication.
o “Can’t read serial data” in sfpshow output. Issuing the sfpshow command again should
resolve this.

Fabric OS v6.3.1c Release Notes v1.0 Page 20 of 84

FCoE/CEE (Brocade 8000 and FCOE10-
FCOE10-24)
• The Brocade 8000 balances the FCoE bandwidth across all six port groups (each port group contains
four ports). To get optimum performance for FCoE traffic it is recommended that the user distribute
server CNA connections across these six port groups.
• Hot plugging a CP with firmware level less than FOS v6.3.0 into a DCX or DCX-4S with an active
FCOE10-24 blade will result in the new standby CP not being HA synchronized. To avoid this scenario,
upgrade the code on the standby CP directly to match the version on the active CP.

• Brocade recommends that Converged Mode be enabled on all interfaces connected to CNAs.

• When operating in Converged Mode, tagged traffic on the native VLAN of the switch interface is
processed normally. The host should be configured not to send VLAN tagged traffic on the switch’s
native VLAN.

• The Converged Network Adapter (CNA) may lose connectivity to the Brocade 8000/FCOE10-24 if the
CNA interface is toggled repeatedly over time. This issue is related to the CNA and rebooting the CNA
restores connectivity.

• Although the Brocade 8000 and FCOE10-24 support the configuration of multiple CEE maps, it is
recommended to use only one CEE map on all interfaces connected to CNAs. Additionally, CEE maps
are not recommended for use with non-FCoE traffic. QoS commands are recommended for interfaces
carrying non-FCoE traffic.

• It is recommended that Spanning Tree Protocol and its variants be disabled on CEE interfaces that are
connected to a server.
• The Fabric Provided MAC Address (FPMA) and the Fibre Channel Identifier (FCID) assigned to a
VN_Port cannot be associated with any single front-end CEE port on which the FLOGI was received.
• LLDP neighbor information may be released before the timer expires when DCBX is enabled on a CEE
interface. This occurs only when the CEE interface state changes from active to any other state.
When the DCBX is not enabled, the neighbor information is not released until the timer expires,
irrespective of the interface state.
• The FCoE Login Group Name should be unique in a fabric wide FCoE Login Management
Configuration. The merge logic is designed to modify the Login Group Name during merge when Login
group names in participating configurations conflict with each other. The current OUI of 00051E is
being used by Brocade, while assigning the WWNs to 8000s, DCXs and DCX4Ss, which would make
only the last 3 bytes as different for any two 8000s, DCXs or DCX4Ss. Considering this assignment
method, the merge logic would rename the login group by including the last 3 bytes of WWN in the
login group name, so that they are unique in the merged configuration.
• For switches having different OUI indices from the 8 assigned to Brocade (for ex: 00051E and
006069), WWNs can differ in more than 3 bytes. In this case, after normal merge and a rename as
per above described logic, login group names can be the same for WWNs differing only in OUIs. The
merge logic would drop one of the Login Groups to satisfy the requirement to keep the Login Group
Name unique in the fabric wide configuration.
• Ethernet switch services must be explicitly enabled using the command “fosconfig –enable ethsw”
before powering on an FCOE10-24 blade. Failure to do so will cause the blade to be faulted (fault 9).
• In order to support non-disruptive firmware upgrades on the DCX/DCX-4S, a new service “ethsw” is
being introduced to enable Ethernet switching on FCOE10-24 in FOS v6.3. LAN switching is disabled
by default in FOS v6.3. The user must explicitly enable Ethernet switch service to prevent FC traffic
interruption using the command “fosconfig –enable ethsw”. Upgrading from FOS v6.x to FOS v6.3 is
non-disruptive. User can enable ethsw after upgrade without FC traffic interruption.

Fabric OS v6.3.1c Release Notes v1.0 Page 21 of 84

 • The Brocade 8000 does not support non-disruptive hot code loads (HCL). Upgrading the Brocade
8000 from FOS v6.1.2_cee1 to FOS v6.3 or from FOS 6.3 to a later FOS version will be disruptive to
the IO through the switch.
• A code load of DCX or DCX-4s with one or more FCOE10-24 blades from FOS 6.3 to another version
will disrupt traffic through the blade.
• Upgrades from FOS 6.3 to future releases will be non-disruptive to data traffic and will have behavior
similar to a CP failover. “ethsw” remains unchanged.
• Downgrade from FOS v6.3 to FOS v6.1.2_CEEx is disruptive if “ethsw’ is enabled on FOS v6.3.
• Downgrade from FOS v6.3 to FOS v6.1.2_CEEx is non-disruptive if “ethsw”” has never been enabled
with FOS v6.3
• HA Failover of CP blades in DCX or DCS-4s will also result in disruption of traffic through the FCOE10-
24 blades.
• Connecting a Brocade 8000 to an FCR-capable switch with fcrbcast config enabled will cause a storm
of broadcast traffic resulting in termination of iswitchd.
• When rebooting a DCX or DCX-4S with an FCOE10-24 blade, Qlogic CNA and LSAN zoning, the switch
will become very unresponsive for a period of time. This is due to the CNA sending excessive MS
queries to the switch.
• An FCOE10-24 blade installed in the highest numbered slot of a DCX or DCX-4S chassis does not send
out FIP unsolicited advertisements. Therefore, it does not support FCoE functionality when installed in
this slot.
Virtual Fabrics:
• On Virtual Fabrics capable platforms, the Virtual Fabrics feature must be enabled in order to utilize the
related capabilities including Logical Switches and Logical Fabrics. On units that ship with FOS v6.3
installed, the Virtual Fabrics feature is enabled by default on capable platforms.
• When creating Logical Fabrics that include switches that are not Virtual Fabrics capable, it is possible
to have two Logical Switches with different FIDs in the same fabric connected via a VF incapable
switch. Extra caution should be used to verify the FIDs match for all switches in the same Logical
Fabric.
• In order to support non-disruptive Hot Code Load on a Brocade 5100 with VF enabled, the total zoning
DB size for the entire chassis should not exceed 1MB.
• A switch with Virtual Fabrics enabled may not participate in a fabric that is using Password Database
distribution or Administrative Domains. The Virtual Fabrics feature must be disabled prior to deploying
in a fabric using these features.
• Virtual Fabrics is not supported on Brocade 7800.
• VF dedicated ISLs are supported on FX8-24 blade. XISLs are not supported.
• On a Brocade 5100 with Virtual Fabrics enabled, ports may be re-initialized causing frame
drops during a hot code load if the switch has a zoning database that is 1MB or larger in size.
To prevent this from occurring, ensure the zoning DB is less than 1MB when activating new
firmware.
Licensing Behavior:
• When operating a switch with Fabric OS v6.3, some licenses may display as “Unknown.” This is due to
changes in licensing requirements for some features that no longer require a license key that may still
be installed on a switch.
• If a Universal temporary license is enabled for a slot-based license feature, the license expiration date
displays as “NA” in Web Tools. Use the licenseshow command to display the correct expiration date.

Fabric OS v6.3.1c Release Notes v1.0 Page 22 of 84

Encryption Behavior for the Brocade Encryption Switch (BES) and FS8-
FS8-18:
• If the data encryption group (Encryption Group) gets into a state where the Group Leader BES reports
that another BES is NOT a member node of the encryption group, and the BES member node still
indicates that it IS part of the encryption group, the following recovery action can be performed to re-
merge the nodes into the encryption group:
1. On the Group Leader BES, execute the CLI command “cryptocfg –dereg –membernode
<WWN of member node>”
2. Wait for 30 seconds
3. Execute the CLI command “cryptocfg –reg –membernode <WWN membernode> <certificate
file name> <ipaddr of member node>”
This is a rare situation that has been noted in a test environment where there were intermittent
management network connectivity problems. A fix for this issue will be provided in an upcoming patch
release.
• The “cryptocfg –manual_rekey –all” command should not be used in environments with multiple
encryption engines (FS8-18 blades) installed in a director-class chassis when more than one
encryption engine has access to the same LUN. In such situations, use the “cryptocfg –manual_rekey
<CTC> <LUN Num> <Initiator PWWN>” command to manually rekey these LUNs.
• In the event an HA Cluster is configured within an Encryption Group with containers configured for
“auto” Failback Mode, the following procedure must be followed when upgrading from FOS v6.2.x to
v6.3.1. Note: This procedure is only required under the above-mentioned conditions:
1. Before the firmware upgrade, change the Failback Mode to “manual” for all containers
configured as “auto”
a. Take note of which Encryption Engines currently own which containers
2. Upgrade all nodes in the Encryption Group to v6.3.1 one node at a time
3. After all nodes have been successfully upgraded, using the notes taken in step 1a, manually
invoke the failback of the containers to the correct Encryption Engine using the following
command:
“cryptocfg –failback –EE <WWN of hosting node> [slot num] <WWN of second node in
HAC> [slot num]
4. Once the manual failback completes, change the Failback Mode back to “auto” from
“manual” if it was changed in step 1
• When adding Nodes to an Encryption Group, ensure all Node Encryption Engines are in an Enabled
state.
• When host clusters are deployed in an Encryption environment, please note the following
recommendations:
o If two EEs (encryption engines) are part of a HAC, configure the host/target pair such that they
form a multipath from both EEs. Avoid connecting both the host/target pairs to the same EE. This
connectivity does not give full redundancy in case of EE failure resulting in HAC failover.
o Since quorum disk plays a vital role in keeping the cluster in sync, please configure the quorum
disk to be outside of the encryption environment.
• During an online upgrade from FOS v6.2.0x to v6.3.1, it is expected to see the IO link status reported
as "Unreachable" when the cryptocfg command is invoked. However, once all the nodes are upgraded
to v6.3.1, the command will accurately reflect the status of the IO Link. The IO link status should be
disregarded during the code upgrade process.
• The “–key_lifespan” option has no effect for “cryptocfg –add –LUN”, and only has an effect for
“cryptocfg --create –tapepool” for tape pools declared “-encryption_format native”. For all other

Fabric OS v6.3.1c Release Notes v1.0 Page 23 of 84

 encryption cases, a new key is generated each time a medium is rewound and block zero is written or
overwritten. For the same reason, the “Key Life” field in the output of “cryptocfg --show -container -all
–stat” should always be ignored, and the “Key life” field in “cryptocfg --show –tapepool –cfg” is only
significant for native-encrypted pools.
• The Quorum Authentication feature requires a compatible DCFM release that supports this feature.
Note, all nodes in the EG must be running FOS v6.3.0 or later for quorum authentication to be properly
supported.
• In a DCX or DCX-4S with FOS 6.3.1 and FS8-18 encryption blades installed, you must set the quorum
size to zero and disable the system card on the blade prior to downgrading to a FOS version earlier
than FOS 6.3.0.
• The System Card feature requires a compatible DCFM release that supports this feature. Note, all
nodes in the EG must be running FOS v6.3.0 or later for system verification to be properly supported.
• The Brocade Encryption switch and FS8-18 blade do not support QoS. When using encryption or
Frame Redirection, participating flows should not be included in QoS Zones.
• Brocade encryption devices can be configured for either disk or tape operation. The ability to
configure multiple Crypto-Target Containers defining different media types on a single encryption
engine (Brocade Encryption Switch or FS8-18 Blade) is not supported. FS8-18 Encryption Blades can
be configured to support different media types within a common DCX/DCX-4S chassis.
• When using Brocade Native Mode, in LKM installations, manual rekey is highly recommended. If auto
rekey is desired, the key expiry date should be configured only when the LUN is created. Never modify
the expiry date after configuring a LUN. If you modify the expiry time, after configuring the LUN the
expiration date will not update properly.
• SKM is supported with Multiple Nodes and Dual SKM Key Vaults. Two-way certificate exchange is
supported. Please refer to the Encryption Admin Guide for configuration information. If using dual
SKMs on BES/FS8-18 Encryption Group, then these SKM Appliances must be clustered. Failure to
cluster will result in key creation failure. Otherwise, register only one SKM on the BES/FS8-18
Encryption Group.
• When the tape key expires in the middle of write operation on the tape, the key is used to append the
data on the tape media. When the backup application rewinds the media and starts writing to Block-0
again and if the key is expired then a new key is created and used henceforth. The expired key
thereafter is marked as read only and used only for restore of data from previously encrypted tapes.
• For dual LKM configuration on the Brocade Encryption Switch (BES) or a DCX/DCX-4S with FS8-18
blades as the primary and secondary key vaults, these LKM appliances must be clustered (linked).
Failure to cluster will result in key creation failure. Otherwise, register only one LKM on the BES/FS8-
18 Encryption Group. Please refer to the Encryption Admin Guide for configuration information.
• The RKM Appliance A1.6, SW v2.5 is supported. The procedure for setting up the RKM Appliance with
BES or a DCX/DCX-4S with FS8-18 blades is located in the Encryption Admin Guide.
• Support for registering a 2nd RKM Appliance on BES/FS8-18 is blocked. If the RKM Appliances are
clustered, then the virtual IP address hosted by a 3rd party IP load balancer for the RKM Cluster must
be registered on BES/FS8-18 in the primary slot for Key Vault IP.
• With Windows and Veritas Volume Manager/Veritas Dynamic Multipathing, when LUN sizes less than
400MB are presented to BES for encryption, a host panic may occur and this configuration is not
supported in the FOS v6.3.1 release.
• HCL from FOS v6.2.x to v6.3.1 is supported. Cryptographic operations and I/O will be disrupted but
other layer 2 traffic will not.
• Relative to the BES and a DCX with FS8-18, all nodes in the Encryption Group must be at the same
firmware level of FOS v6.2 or v6.3 before starting a rekey or First Time Encryption operation. Make
sure that existing rekey or First Time Encryption operations complete before upgrading any of the

Fabric OS v6.3.1c Release Notes v1.0 Page 24 of 84

 encryption products in the Encryption Group. Also, make sure that the upgrade of all nodes in the
Encryption Group to FOS v6.3.1 completes before starting a rekey or First Time Encryption operation.
• To clean up the stale rekey information for the LUN, follow one of the following two methods:
Method 1:
1. First, modify the LUN policy from “encrypt” to “cleartext” and commit. The LUN will
become disabled.
2. Enable the LUN using “cryptocfg --enable –LUN”. Modify the LUN policy from “clear-text”
to “encrypt” with “enable_encexistingdata” to enable the first time encryption and do
commit. This will clear the stale rekey metadata on the LUN and the LUN can be used
again for encryption.
Method 2:
1. Remove the LUN from Crypto Target Container and commit.
2. Add the LUN back to the Crypto Target Container with LUN State=”clear-text”,
policy=”encrypt” and “enable_encexistingdata” set for enabling the First Time Encryption
and commit. This will clear the stale rekey metadata on the LUN and the LUN can be
used again for encryption
• nCipher / Thales key vault support troubleshooting tips:
o Regarding NCKA key vault (KV) communication with a Brocade encryption group, the default
communication port setting for the NCKA KV is 37208, however, the Brocade encryption
members and leader use 9000 so this needs to be reset on NCKA. Additionally, the following
is a checklist of things to review if the initial attempt to connect to the KV fails:

Check physical and logical connection via a ping on port 9000, this should be the
first check.

For the group leader node, the kac client cert and the kv cert files are to be identical.

For group member nodes the kv file is to be the same as the kv file on the group
leader node.

Crosscheck to ensure the private key file corresponds to the kac public cert file on
any node.
• Host encrypted tape I/O may fail to start when the Primary LKM of an LKM key vault cluster is down.
When the primary LKM is down, key creation requests can be rejected by the secondary LKM. NetApp
is aware of this issue and is tracking it internally with their defect management tool. The workaround
in this case is to wait until the offline LKM comes back online and retry.
• In an environment with a mixed FW version (FOS 6.2.x + 6.3.1) Encryption Group, the IO link state
reported for 6.2.x nodes is unreachable. During a rolling upgrade from 6.2.0x release to 6.3.1, it is
expected to see the IO link status reported as "Unreachable" when the cryptocfg –show -loc command
is invoked. However, once all the nodes are upgraded to the 6.3.1 release, then the show command
will accurately reflect the status of the IO Link. The IO link status while performing the rolling upgrade
from 6.2.0 to 6.3.1 release can be ignored until all nodes have been upgraded to 6.3.1.
Mace39:root> cryptocfg --show -loc

EE Slot: 0
SP state: Online
Current Master KeyID: 43:f1:bd:dc:91:89:f2:f1:6a:a1:48:89:7b:d0:5f:59
Alternate Master KeyID: 3a:a4:5b:86:90:d5:69:26:29:78:f8:3b:f9:b2:9c:b9
HA Cluster Membership: hac39_115
EE Attributes:
Link IP Addr : 10.32.50.36
Link GW IP Addr: 10.32.48.1

Fabric OS v6.3.1c Release Notes v1.0 Page 25 of 84

 Link Net Mask : 255.255.240.0
Link MAC Addr : 00:05:1e:53:8a:86
Link MTU : 1500
Link State : UP
Media Type : DISK
System Card Label :
System Card CID :

Remote EE Reachability :

Node WWN/Slot EE IP Addr EE State IO Link State

10:00:00:05:1e:53:77:80/0 10.32.53.107 EE_STATE_ONLINE Non--Reachable
Non
10:00:00:05:1e:53:b7:ae/0 10.32.53.105 EE_STATE_ONLINE Non-
Non-Reachable
Adaptive Networking/Flow-
Networking/Flow-Based QoS Prioritization:
• When using QoS in a fabric with 4G ports or switches, FOS v6.0 or later must be installed on all
products in order to pass QoS info. E_Ports from the DCX to other switches must come up after FOS
v6.0 is running on the switches.
• Flow based QoS is NOT supported on FC8 blades in the Brocade 48000.
• Any products that are not capable of operating with FOS 6.0 may NOT exist in a fabric with Flow based
QoS. Major problems will occur if previous generation 2G products exist in the fabric.
• The resolution for defect 250438 included in this release changes the default behavior of the
Adaptive Networking QoS feature. Please refer to the Documentation Updates section of this
document for further details.
• QoS is supported on AG switches with FOS 6.3.0 and later. The fabric switches should be running 6.3
in order to support QoS. If the fabric switch is 6.2, QoS must be disabled on either switch or AG.
Access Gateway
• When running Adaptive Networking in AG mode note the following:
o QoS takes precedence over ingress rate limiting
o Ingress Rate Limiting is not enforced on trunked ports.
FCR
• IPFC over FCR is now disabled by default. Switches that are upgraded to FOS v6.3 will retain their
configuration settings for IPFC over FCR. The change to the default configuration only applies to new
units shipping with FOS v6.3 or units running v6.3 that are reset to a default configuration. Use
fcrbcast - - enable to explicitly enable IPFC over FCR.
• Broadcast frame forwarding is not supported in an FCR fabric with a Brocade 8000. By default,
broadcast frame forwarding is disabled on the FC router. If your edge fabric includes a Brocade 8000,
do not enable broadcast frame forwarding on the FC router because this can degrade FCR
performance when there is excessive broadcast traffic.
• With FC8 blades, the switch must be disabled to change the backbone fabric ID
• With routing and dual backbone fabrics, the backbone fabric ID must be changed to keep the IDs
unique.
• When using FC Routing in a backbone to edge configuration with an Mi10K in the edge fabric, users
may experience slow throughput for hosts attached to the Mi10K. Users may encounter this following
a bounced IFL connection between the backbone and edge fabric. This slowdown can be resolved by
disabling/enabling the Mi10K ports for the hosts that are impacted.
• Mi10K Directors operating with firmware prior to M-EOSn v9.9.5 may experience repeated system
faults when attached as an FCR edge switch to a Brocade 7800 EX Port. To avoid this, ensure that the

Fabric OS v6.3.1c Release Notes v1.0 Page 26 of 84

 Mi10K is operating with M-EOSn v9.9.5 or later when in an edge fabric that will be attached to a
Brocade 7800 FCR Backbone.
FC FastWrite
• When an FC FastWrite Initiator is moved to a port that doesn't have FC FastWrite enabled, I/O will
recover and revert to the slow path route (non FC FastWrite). This is a behavioral change from FOS
v6.2.x.
Traffic Isolation over FCR
• All switches and Fibre Channel Routers both in edge and backbone fabrics must be running FOS
v6.1.0 or later in order to support this feature.
• In order for Traffic Isolation over FCR to function properly, the associated TI zones in each fabric (both
edge fabrics and backbone fabric) need to have failover ENABLED.
• TI over FCR is only supported in edge-to-edge configurations. There is no support for TI in backbone to
edge routing configurations.
Integrated Routing
• To allow Hot Code Load on a Brocade 5100 when using Integrated Routing, the edge switch
connected to the 5100 must be running Fabric OS v6.1 or later code.
• Integrated Routing EX_Ports are only supported in the base switch on a switch with VF enabled.
• Integrated Routing and TopTalkers (Fabric Mode) are not concurrently supported in FOS v6.3. To use
Integrated Routing, be sure to disable Fabric Mode TopTalkers prior to configuring EX_Ports first.
Native Connectivity
• FOS-based platforms operating in interopmodes 2 or 3 should never be deployed in a fabric without at
least one M-series switch. FOS switches in interopmode 3 (McDATA Open Fabric Mode) do not support
configuration of zoning without an M-series switch in the fabric. When migrating from M-series to B-
series switches, all B-series switches should be configured to interopmode 0 (Brocade Native mode)
once the last M-series switch has been removed from the fabric.
• M-EOSc switches may exhibit a behavior where they block all attached devices with a reason
indication of “Blocked Temporarily, Internal”. Users that experience this may have power cycled the
M-series switch while it was participating in a fabric with Frame Redirection zoning, a capability used
for FOS-based application or encryption services . If the switch is still participating in the fabric with
Frame Redirection, issue the “cfgsave” command from a Brocade FOS-based switch with the Frame
Redirection zone in its defined zone database. If the M-EOS switch is no longer attached to the fabric
with Frame Redirection zoning, issue the “Config.Zoning.deleteSplZoneSet” command via CLI to the M-
EOS switch.
FCS Automatic Distribution
• When using the FCS Automatic Distribution feature in Fabric OS v6.0 or later, all switches in the fabric
must be running FOS v6.0 or later. Only manual distribution can be used if any switches are running
FOS v5.x or earlier.
• FOS v6.0 or later will only allow FCS automatic distribution when in strict mode, requiring only switches
with FOS v6.0 or later.
FCAP
• Due to limitations with the certificates, FCAP authentication cannot be supported on user defined
logical switches. FCAP will continue to function with existing certificates for non-VF and the default
logical switch of VF enabled switches. (Note: authutil is not restricted from other logical switches, at
this time, so this can still be enabled on unsupported LS.)
• pkicert (1.06) utility may cause evm errors, so each new switch should be isolated from fabric, in non-
vf mode, to install new certificates.

Fabric OS v6.3.1c Release Notes v1.0 Page 27 of 84

 • For FIPS mode, certificates need to be installed prior to FIPS activation.
FL_Port (Loop) Support
• The FC8-48 blade supports attachment of loop devices in the DCX and DCX-4S.
• Virtual Fabrics must be enabled on the chassis and loop devices may only be attached to ports on a
48-port blade assigned to a non-Default Logical Switch operating with the default 10-bit addressing
mode (they may not be in the default Logical Switch).
• A maximum of 144 ports may be used for connectivity to loop devices in a single Logical Switch within
a chassis.
• Loop devices continue to be supported when attached to ports on the FC8-16, FC8-32, FC4-16 and
FC4-32 blades with no new restrictions.
Port Mirroring
• On the Brocade 5300, the port mirroring feature has a limitation where all port mirror resources must
stay within the same ASIC port group. The resources are the configure mirror port, Source Device, and
Destination Device or ISL, if the Destination Device is located on another switch. The ASIC port groups
are 0-15, 16-31, 32-47, 48-63, and 64-79. The routes will be broken if the port mirror resources are
spread across multiple port groups.
• Port Mirroring is not supported on the Brocade 7800.
10G Interoperability
• 10G interop between FC10-6 and McDATA blades is not supported due to a HW limitation, however
the FC10-6 is supported in a chassis running in Interopmode 2 or 3 (FC10-6 to FC10-6 connections
only). An FC10-6 blade will not synchronize with a McDATA 10G blade. However, the inability to
synchronize will not negatively impact the system.
Port Fencing
• For Port Fencing, once the trigger threshold is exceeded (e.g. for ITWs or CRCs or LRs), Fabric Watch
will wait for approximately six seconds to see if the port is going offline. If it is still online at the next
poll cycle, FW will fence the port. Extensive testing has shown that ports that are in the process of
going offline may exhibit bursts of errors. Waiting the additional six seconds to check the port status
helps prevent false positives and unnecessarily fencing a port (e.g. during a server reboot).
• When using the Port Fencing feature, you must first run the fwalarmsfilterset command. This
command enables the port and allows you to receive Port Fencing messages.
• The state changes counter used by Fabric Watch in FOS v6.3 has been updated to ignore any toggling
of F-ports due to planned internal mechanisms such as throttling and trunking. There are some FOS
CLI commands such as portcfgspeed, portCfgTrunkPort etc that implicitly disable/enable ports after
configuration.
• Fabric Watch monitors state change for LISL ports though it is not being displayed in Fabric Watch CLI
commands.
• The Port Fencing feature is not supported for Loss of Sync (LOS) and Link Failure (LF) areas of Port/F-
port/E-port classes. State change area can be used in place of LOS/LF areas for Port Fencing.
ICLs
• If a DCX with an 8-link ICL license is connected to a DCX with a 16-link license, the DCX with the 16-
link license will report enc_out errors. The errors are harmless, but will continue to increment. These
errors will not be reported if a DCX with a 16-link license is connected to a DCX-4S with only 8-link ICL
ports.
• If ICL ports are disabled on only one side of an ICL link, the enabled side may see enc_out errors.

Fabric OS v6.3.1c Release Notes v1.0 Page 28 of 84

Extended Fabrics and R_RDY Flow Control
Beginning with Fabric OS v5.1, Brocade supported the Extended Fabrics feature in conjunction with
R_RDY flow control (R_RDY flow control mode can be enabled via portCfgISLMode command). R_RDY
flow control mode that uses IDLE primitives does not support Brocade frame-based Trunking for
devices such as Time Division Multiplexor (TDM.) In order to overcome this limitation and provide
support for frame-based Trunking with Extended Fabrics, Fabric OS v6.2.0 and later has been
enhanced to support interoperability with these distance extension devices.
Fabric OS v6.3.1 allows Extended Fabrics E_Ports to operate in VC_RDY mode using either ARB or
IDLE primitives as fill-words. This allows frame-based Trunking to be supported on Extended Fabrics E-
ports even when IDLE primitives are configured for these ports when operating in native VC_RDY
mode. Prior to this change, frame-based Trunking was supported only when ARB primitives were used
in VC_RDY mode. With Fabric OS v6.2 or later, frame-based Trunking is supported on Extended
Fabrics E_Ports regardless of whether IDLE or ARB primitives are used when operating in native
VC_RDY mode.
Implementation
The portcfglongdistance CLI parameter “VC Translation Link Init” is now overloaded to specify if the
long distance link should use IDLE or ARB primitives. By default, vc_init is enabled. If vc_init is
enabled, the long distance link will use ARB primitives. If vc_init is disabled, the link will use IDLE
primitives.
Note: Buffer-to-Buffer Credit Recovery feature is not supported on Extended Fabrics E_Port when it is
configured to use IDLE primitives. The user must disable buffer-to-buffer credit recovery feature
using the command portcfgcreditrecovery and specifying the disable option; otherwise, the link
will continuously reset.
The Adaptive Networking SID/DID Traffic Prioritization QoS feature is not supported on Extended
Fabrics E_Ports when IDLE primitives are configured on these ports. This is because in this mode
only data Virtual Channels are available while QoS related virtual channels are not available.
When connecting to an extension device that does not support ARB primitives (such as some TDM
products), the following configuration must be used:
portcfgqos -disable <port>
portcfgcreditrecovery –disable <port>
portCfgLongDistance <port> <LD|LD> 0 <distance>
The fabric parameter “fabric.ops.mode.longdistance” is now deprecated and should not be used.
Miscellaneous
• During non-disruptive firmware upgrades, E_Ports in R-RDY mode may cause some frame
drops on the E-port links.
• Modem capability for the 48000 is not supported in FOS v6.2.0 and later.
• The portCfgFillWord command, applicable to 8G-capable ports, has been enhanced with FOS
v6.3.1 to provide two new configuration options (Modes 2 and 3). The available settings
include:
Mode Link Init/Fill Word
Mode 0 IDLE/IDLE
Mode 1 ARBF/ARBF
Mode 2 IDLE/ARBF
Mode 3 If ARBF/ARBF fails use IDLE/ARBF

Fabric OS v6.3.1c Release Notes v1.0 Page 29 of 84

 Although this setting only affects devices logged in at 8G, changing the mode is disruptive
regardless of the speed at which the port is operating. The setting is retained and applied any
time an 8G device logs in. Upgrades to FOS v6.3.1 from prior releases supporting only modes
0 and 1 will not change the existing setting, but switches reset to factory defaults with FOS
v6.3.1 will be configured to Mode 0 by default. The default setting on new units may vary by
vendor.
Modes 2 and 3 are compliant with FC-FS-3 specifications (standards specify the IDLE/ARBF
behavior of Mode 2, which is used by Mode 3 if ARBF/ARBF fails after 3 attempts). For most
environments, Brocade recommends using Mode 3, as it provides more flexibility and
compatibility with a wide range of devices. In the event that the default setting or Mode 3
does not work with a particular device, contact your switch vendor for further assistance.

Fabric OS v6.3.1c Release Notes v1.0 Page 30 of 84

Documentation Updates
This section provides information on last-minute additions and corrections to the
documentation. The most recent Fabric OS v6.3 documentation manuals are available on the
Brocade Partner Network: http://partner.brocade.com/. The updates noted in this section
are in addition to those included in the Fabric OS v6.3.0a, v6.3.0b and v6.3.0c Release
Notes.
Note: The FOS FCIP Admin Guide and FOS Command Reference Manuals have been updated
to reflect new support and changes in FOS v6.3.1.

Brocade Access Gateway Administrator’s Guide (Publication Number 53-

53-1001760-
1001760-01)
On page 10, in the section “Access Gateway Mapping,” add the following section:

Brocade 8000 mapping differences

The Brocade 8000 contains up to 24 internal FCoE ports and eight external Fibre Channel ports. In
Access Gateway mode, the FCoE ports are configured as F_Ports, while the Fibre Channel ports are
configured as N_Ports. The FCoE ports are divided into six groups or trunks consisting of four ports
each. All four ports in a group are mapped to one N_Port. Although you can change the default F_Port
group to N_Port mapping for these groups (refer to “Default port mapping” on page 13), consider the
following when working with these FCoE ports:
• All four FCoE ports in the port group are mapped to the same Fibre Channel N_Port.
• You cannot map individual FCoE ports within the same port group to different Fibre Channel
ports.
• Any Access Gateway operation that involves moving F_Ports will move all FCoE ports in the
group.
• All four FCoE ports in a group will failover or failback to one Fibre Channel N port.
• All four FCoE ports are considered as a unit for rebalancing.

On page 11 under the “Default Port Mapping” section, add the following information for Brocade 8000
default F_Port to N_Port mapping:

Brocade Total Ports F_Ports N_Ports Default F_ to N_Port Mapping

Model

8000 32 8-31 0-7 8-11 mapped to 0

12-15 mapped to 1
FCoE ports mapped Fibre Channel ports 16-19 mapped to 2
as F_Ports. mapped as N_Ports 20-23 mapped to 3
with failover and 24-27 mapped to 4
failback policy 28-31 mapped to 5
enabled.

Fabric OS v6.3.1c Release Notes v1.0 Page 31 of 84

Defects
Closed with Code
Code Change in Fabric OS v6.3.1c
v6.3.1c
This section lists the defects with Critical, High and Medium Technical Severity closed with a code change as
of May 18, 2010 in Fabric OS v6.3.1c.

Defect ID:
ID DEFECT000269189 Technical Severity:
Severity Medium
Summary:
Summary SERDES tuning values to support BR–804 HBA
Symptom:
Symptom Fine tune SERDES value for BR–804 HBA support. This change only applies to Brocade 5480
platform.
Feature:
Feature Embedded Platform Services Function:
Function Brocade 5480
Probability:
Probability Medium
Found in Release:
Release FOS6.3.0
Where Else Fixed: FOS6.4.0, FOS6.3.1 a, FOS6.3.1 b

Closed with Code Change in Fabric OS v6.3.1b

v6.3.1b
This section lists the defects with Critical, High and Medium Technical Severity closed with a code change as
of April 20, 2010 in Fabric OS v6.3.1b.

Defect ID:
ID DEFECT000269942 Technical Severity:
Severity High
Summary:
Summary On the Brocade 7800 and FX8-24, with emulated tape and tape pipeline, if there is frame drop
on back end, read tape pipeline does not handle the error and causes tape access to hang.
Back end read IO recovery needs enhanced for tape emulation .
Symptom:
Symptom When running emulated tape and tape pipeline on the Brocade 7800 and FX8-24 blade running
FOS 6.3.1 or 6.3.1a, tape access can hang when there is a frame drop on the back end.
Feature:
Feature FCIP Function:
Function Emulation
Probability:
Probability Medium
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000274646 Technical Severity:
Severity High
Summary:
Summary Brocade 8000 installed with FOS v6.3.0 through v6.3.0c, v6.3.1 and v6.3.1a panics doing
firmwaredownload.
Symptom:
Symptom Switch panic reported during firmware download. This only applies to Brocade 8000s factory
installed with FOS v6.3.0 through v6.3.0c, v6.3.1 and v6.3.1a.
Workaround:
Workaround Before upgrading from FOS v6.3.0 through v6.3.0c, v6.3.1 or v6.3.1a, check if /dev/altera is
present in secondary partition. If not present, copy it from primary partition via "cp
/dev/altera /mnt/dev/altera".
Feature:
Feature CEE-Infrastructure Function:
Function Zues Driver
Probability:
Probability High
Found in Release:
Release FOS6.4.0

Fabric OS v6.3.1c Release Notes v1.0 Page 32 of 84

 Closed with Code Change in Fabric OS v6.3.1b

Defect ID:
ID DEFECT000277910 Technical Severity:
Severity High
Summary:
Summary FCR iswitchd skips slot recovery during warm boot with no base switch, causing devices not to
get imported after adding a base switch.
Symptom:
Symptom After having gone through warm recovery with no base switch configured, devices are not getting
imported after adding a base switch to switches with VF and FCR configured. Switch stays in
initializing state in an EtoE FCR fabric. This impacts Brocade DCX, DCX-4S, 5300 and 5100
platforms only.
Workaround:
Workaround Hafailover/hareboot and then toggling the EX_Port to recover or make sure base switch is
configured before hafailover/hareboot.
Feature:
Feature 8G FCR Function:
Function FCR Daemon
Probability:
Probability High
Found in Release:
Release FOS6.4.0

Defect ID:
ID DEFECT000278461 Technical Severity:
Severity High
Summary:
Summary During hot code load, BP did not reboot after relocation of the internal image.
Symptom:
Symptom Under very rare condition, sometime intelligent switch lost communication between BP and CP
and cause firmware download to fail with raslog SULB-1035 and switch would come up faulty.
This impacts Brocade 7500 and 7600
Workaround:
Workaround reboot for the new image to take effect.
Feature:
Feature Infrastructure Function:
Function Firmware Download
Probability:
Probability Low
Found in Release:
Release FOS6.4.0

Defect ID:
ID DEFECT000279401 Technical Severity:
Severity High
Summary:
Summary Internal race condition and semaphore lock contention caused FX8-24 initialization to fail and
switch to panic after blade hot plugged into the chassis
Symptom:
Symptom FX8-24 fails to initialize and causes a switch panic after being hot plugged into the chassis.
Workaround
Workaround:
karound Remove the GE SFP(s), put the blade in chassis and insert the SFPs after firmware auto-
leveling is completed.
Feature:
Feature Striker/Spike Platform Services Function:
Function BFOS
Probability:
Probability Low
Found in Release:
Release FOS6.4.0

Fabric OS v6.3.1c Release Notes v1.0 Page 33 of 84

 Closed with Code Change in Fabric OS v6.3.1b

Defect ID:
ID DEFECT000280910 Technical Severity:
Severity High
Summary:
Summary Added various optional RAS features to help identify slow drain device(s), handle stuck Virtual
Channels (VC), and credit loss conditions. Improved bottleneck detection on both 4G and 8G
platforms. Added transmit timeout counter support for 4G switches
Symptom:
Symptom Customer notices fabric performance being sluggish, SCSI timeout on hosts or fabric wide frame
drop. These can be triggered by several causes including a device port being slow, or credit issue
that backpressure frames into fabric. The Fabric will drop frames after a holding time is
exceeded. This release has optional RAS features that can be turned on to help customers
detect the existence of such problems and to identify the trouble spot or problem device(s). It
also allows setting different hold times at edge fabric to alleviate congestion if appropriate.
Feature:
Feature FABRIC WATCH Function:
Function PORT FENCING
Probability:
Probability Low
Found in Release:
Release FOS6.4.0

Defect ID:
ID DEFECT000283637 Technical Severity:
Severity High
Summary:
Summary Race condition encountered during extensive writes to compact flash causes long HA recovery
times during hot code load
Symptom:
Symptom Long HA recover times seen during hot code load. This can cause link reset or frame drops when
credit is not returned in time. Affects the VF environment and connecting switch operating under
single virtual channel credit model more extensively and can happen on both director and switch
platforms.
Feature:
Feature Infrastructure Function:
Function PDM/PortCfg
Probability:
Probability Low
Found in Release:
Release FOS6.4.0

Defect ID:
ID DEFECT000284426 Technical Severity:
Severity High
Summary:
Summary Brocade 5470 encountering extremely high enc out errors on ports connected to 3rd party HBAs
may experience link related problems
Symptom:
Symptom High "enc out" errors in the porterrshow CLI, which may cause link related problems.
Feature:
Feature Embedded Platform Services Function:
Function Balzer3
Probability:
Probability High
Found in Release:
Release FOS6.4.0

Defect ID:
ID DEFECT000286104 Technical Severity:
Severity High
Summary:
Summary With FMS enabled and switch in VF mode, all ports on the FC8-48 become persistently disabled
after upgrading from FOS v6.2.x to FOS v6.3.x.
Symptom:
Symptom After upgrading from FOS v6.2.x to FOS v6.3.x on systems with FC8-48 blades installed, VF
disabled and fmsmode enabled, all ports on the FC8-48 blades become persistently disabled
without warning.
Workaround:
Workaround Manually re-enable ports, no other viable workaround at this time
Feature:
Feature Field Escalation Function:
Function FICON
Probability:
Probability High
Found in Release:
Release FOS6.3.0 Service Request ID:
ID 423415
Where Else Fixed:
Fixed: FOS6.4.0

Fabric OS v6.3.1c Release Notes v1.0 Page 34 of 84

 Closed with Code Change in Fabric OS v6.3.1b

Defect ID:
ID DEFECT000286238 Technical Severity:
Severity High
Summary:
Summary Memory issues in manageability modules causes OOM panic during configDownload
Symptom:
Symptom Customer may experiences switch panic or cannot execute any command after shared memory
segments or memory shortage. It can be exposed via:
• Create and remove logical switch multiple times
• Perform configdownload with a large configuration file or repeat configdownload
• Run repeat perfresourceshow commands with option "eeRes" or "fportRes"
• Launch port admin and select GbE port tab and keep it open for long time (2 hours)
• Cald is busy to respond back to rpcd for some xml requests that cause stale shared memory
segments
Feature:
Feature OS Services Function:
Function Other
Probability:
Probability Low
Found in Release
Release:
ease FOS6.4.0

Defect ID:
ID DEFECT000286865 Technical Severity:
Severity High
Summary:
Summary Different PID formats between edge and backbone fabrics, after a large number of device
online/or insertion events, device import failed with FCR-1022 message
Symptom:
Symptom If backbone and edge fabric have different switch PID formats such as when edge fabric is in
IM2 mode, while backbone fabric is not, importing another device into the backbone will fail with
[FCR-1022] " Local proxy device slot entries exhausted" in raslog. Both 4G and 8G FCRs are
impacted and are more likely to be seen if there is frequent device offline/online in edge fabrics.
Feature:
Feature Field Escalation Function:
Function FCR
Probability:
Probability Low
Found in Release:
Release FOS6.1.0 Service Request ID:
ID 423429
Where Else Fixed: FOS6.4.0

Defect ID:
ID DEFECT000288756 Technical Severity:
Severity High
Summary:
Summary Not able to download fabricwatch settings to switch when there are mismatched names
(LinkReset/LReset) used in the configuration file
Symptom:
Symptom Unable to replicate Fabric Watch setting to switch using DCFM. Switch fails with raslog [CONF-
1023], 357, SLOT 7 | FID 128, INFO, , configDownload failed for switch. This will ONLY happen
when there is linkreset setting in configuration files, such as “thresh.cust.eport.Linkreset.above”
Workaround
Workaround: Once the switch is disabled, the configuration downloaded, and the switch re-enabled, the
configuration can be modified and downloaded without any problems. Or remove or comment
out the link reset settings in the .cfg file.
Feature:
Feature Field Escalation Function
Function:
nction Management Services
Probability:
Probability Medium
Found in Release:
Release FOS6.3.0
Where Else Fixed: FOS6.4.0

Fabric OS v6.3.1c Release Notes v1.0 Page 35 of 84

 Closed with Code Change in Fabric OS v6.3.1b

Defect ID:
ID DEFECT000289981 Technical Severity:
Severity High
Summary:
Summary Under very rare condition of a heartbeat lost while active is running FOS v6.3.x and standby CP is
running FOSv6.2.x, switch was reset.
Symptom:
Symptom Directors cold boot. This can only happen when heart beat was lost (such as backend Ethernet
connection had transient problem) while standby CP is on FOSv6.2.x and active CP is running
FOS6.3.x on directors, during firmware download.
Feature:
Feature High Availability Function:
Function Switch hareboot/HCL
Probability:
Probability Low
Found in Release:
Release FOS6.2.0

Defect ID:
ID DEFECT000297978 Technical Severity:
Severity High
Summary:
Summary Zoned terminated while activating zoning from DCFM
Symptom:
Symptom Unexpected reboot and failover if attempt to push zone DB from DCFM in IM2/IM3 fabrics only.
Workaround:
Workaround Use CLI (or ECFM for non-TI/Redirect zones) in IM2/IM3
Feature:
Feature FC Services Function:
Function Zoning
Probability:
Probability Medium
Found in Release:
Release FOS6.4.0

Defect ID:
ID DEFECT000263476 Technical Severity:
Severity Medium
Summary:
Summary In fabric router environment, WWN for a device is showing up in multiple edge fabrics.
Symptom:
Symptom Proxy devices for the same host/target could be created in unintended fabric which could cause
traffic be sent to the wrong fabric and host does not see target. It happens when there is
frequent F port bounce (1-2 sec) in FCR fabric. This impacts all FCR platforms such as 7500,
FR4-18i and 8G Integrated Router platforms. This defect only exists in FOS v6.3.x.
Feature:
Feature 8G FCR Function:
Function FCR Daemon
Probability:
Probability Medium
Found in Release:
Release FOS6.4.0

Defect ID:
ID DEFECT000269189 Technical Severity:
Severity Medium
Summary:
Summary SERDES tuning values to support BR–804 HBA
Symptom:
Symptom Fine tune SERDES value for BR–804 HBA support. This change only applies to Brocade 5480
platform.
Feature:
Feature Embedded Platform Services Function:
Function Bulova
Probability:
Probability Medium
Found in Release:
Release FOS6.3.0
Where Else Fixed: FOS6.4.0, FOS6.3.1 a

Fabric OS v6.3.1c Release Notes v1.0 Page 36 of 84

 Closed with Code Change in Fabric OS v6.3.1b

Defect ID:
ID DEFECT000270651 Technical
Technical Severity:
Severity Medium
Summary:
Summary 4G switch does not responding to Link Reset primitives correctly
Symptom:
Symptom Under a small timing condition, after reboot or switchdisable and switchenable, or when device
detect credit shortage, devices sent a LR to switch and switch does not respond to it and link
went down. This only applies to 4G switches/directors.
Workaround:
Workaround portdisable/portenable the ports a few times
Feature:
Feature FICON Function:
Function MS-FICON
Probability:
Probability Low
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000281765 Technical Severity:
Severity Medium
Summary:
Summary AG NPIV port disabled as "initiator/target connected on N_Port" after upstream BES switch was
rebooted or a FS8-18 executes a Power On Self Test (POST).
Symptom:
Symptom When bpportloopbacktest is run as part of a POST on BES or FS8-18, loop back mode caused
the FLOGI frames from the AG ports on AG switch to loopback and further disable these AG ports
. Switchshow on AG switch reports:
0 0 5a0000 id N8 In_Sync FC Disabled (Initiator/Target connected to N-Port)
1 1 5a0100 id N8 No_Sync FC Disabled (Initiator/Target connected to N-Port)
Workaround:
Workaround Disable POST on BES or chassis with FS8-18 or reenable the AG ports manually
Feature:
Feature Diagnostics Function:
Function Other
Probability:
Probability High
Found in Release:
Release FOS6.4.0

Defect ID:
ID DEFECT000281774 Technical Severity:
Severity Medium
Summary:
Summary After Brocade7800 reboot, seeing PLOGI aborts due to F_RJT for the ACCEPT frame
Symptom:
Symptom Host cannot see target if PLOGI comes in before RSCN is propagated on Brocade 7800 and FX8-
24 on VE port, due to backend port programming did not complete in time. This applies to both
FICON and non-FICON setup but only extension platform and on VE ports.
Feature:
Feature Striker/Spike Platform Services Function:
Function Spike Platform Module
Probability:
Probability Medium
Found in Release
Release:
ease FOS6.4.0

Defect ID:
ID DEFECT000283519 Technical Severity:
Severity Medium
Summary:
Summary Encryption switch panic due to daemon termination.
Symptom:
Symptom In corner case, BES switch or FS8-18 did not handle an error case correctly with key attribute
retrieval operation in daemon kacd.
Feature:
Feature Data Security Function:
Function Key Vault
Probability:
Probability Low
Found in Release:
Release FOS6.3.0 Service Request ID:
ID 421755
Where Else Fixed: FOS6.4.0

Fabric OS v6.3.1c Release Notes v1.0 Page 37 of 84

 Closed with Code Change in Fabric OS v6.3.1b

Defect ID:
ID DEFECT000284435 Technical Severity:
Severity Medium
Summary:
Summary Switch panic after daemon iswitchd coredump
Symptom:
Symptom With two FCRs in the back bone and both are connect to same edge fabric through EX-ports, and
edge fabric has MEOS in IM2 mode, upon receiving periodic GE_PT from M-EOS switches, FCR
did not handle properly cause memory issues. Later iswitchd could coredump due to access to
the bad memory. switch is reboot/hafailover when it happens.
Feature:
Feature 8G FCR Function:
Function FCR Daemon
Probability:
Probability Low
Found in Release:
Release FOS6.2.1 Service Request ID:
ID 421137
Where Else Fixed: FOS6.4.0

Defect
Defect ID:
ID DEFECT000287036 Technical Severity:
Severity Medium
Summary:
Summary portCfgFillWord enhancement for various 8G devices
Symptom:
Symptom In portCfgFillWord with fillword mode 3, a 3rd party device cannot come up on line. Workaround
the device issue by adding OLS as the trigger for the auto-switch from arb/arb to idle/arb when
port is configured to mode 3. In addition, for Brocade-804 Mez HBA, regardless what the mode
setting is on the port, it will operate at mode 1 internally with embedded switch Brocade 5480.
Feature:
Feature 8G Platform Services Function:
Function FOS Kernel Drivers
Probability:
Probability Low
Found in Release:
Release FOS6.3.1
Where Else Fixed: FOS6.3.1, FOS6.4.0

Defect ID:
ID DEFECT000287423 Technical Severity:
Severity Medium
Summary:
Summary Brocade 7800 and FX8-24 does not always auto-restart after detection of a critical error.
Symptom:
Symptom FOS 6.3.1 and 6.3.1a may not always auto-restart depending on the critical error encountered. A
manual reboot may be needed to recover Brocade 7800, and slotpower off/on to recover FX8-
24.
Feature:
Feature Striker/Spike Platform Services Function:
Function Blade Driver
Probability:
Probability High
Found in Release:
Release FOS6.3.1

Defect ID:
ID DEFECT000287809 Technical Severity:
Severity Medium
Summary:
Summary Race condition on BES/FS8-18 node join/leave event causes encryption switch cluster to update
continuously and support save not to finish
Symptom:
Symptom Supportsave hangs after unplugging and then plugging in the network cable on BES/FS8-18
platforms
Feature:
Feature Data Security Function:
Function Infrastructure
Probability:
Probability Low
Found in Release:
Release FOS6.3.1

Fabric OS v6.3.1c Release Notes v1.0 Page 38 of 84

 Closed with Code Change in Fabric OS v6.3.1b

Defect ID:
ID DEFECT000288832 Technical Severity:
Severity Medium
Summary:
Summary On Brocade 5460 platform, firmware version was being set to the FOS default value string, not
the proper version string
Symptom:
Symptom Firmware version string always shows FOS default on Brocade 5460, not the correct version
through 3rd party SVP.
Feature:
Feature Embedded Platform Services Function:
Function Sys-Control/Environment Monitor
Probability:
Probability Low
Found in Release:
Release FOS6.3.1

Defect ID:
ID DEFECT000290539 Technical Severity:
Severity Medium
Summary:
Summary On the Brocade 300, 5100, and 5300 switches shipped from the factory with FOS v6.3.0a, b, c,
d, v6.3.1 and v6.3.1a, the assignment of PIDs (FCIDs) is non-deterministic.
Symptom:
Symptom If customer has factory installed switches (Brocade 5300, 5100 and Brocade 300), shipped with
FOS v6.3.0a,b,c,d, FOS v6.3.1, and FOS v6.3.1a, the area field of the PIDs will be assigned
based on the order ports are recognized and brought up by the system the first time (and only
the first time) it is booted. Each Switch port PID’s area will not equal its port number, which may
impact servers (such as FICON servers, or static PID binding servers) that need their area equal
to the port numbers to login to the fabric successfully. This issue does not impact switches that
are upgraded from FOS v6.2.x to v6.3.0a,b,c,d, v6.3.1 and v6.3.1a, as PIDs are persistent
across reboot and upgrade once they are assigned. An example of non-port based assigned PIDs
from switchshow:
0 0 401700 -- N8 No_Module FC
1 1 401500 -- N8 No_Module FC
Workaround:
Workaround In environments with devices that rely on the area of the PID to match the port number, users
should bind PIDs using the portaddress --bind [slot_number/]port_number [16-bit_address]
command prior to allowing devices to log in to switch.
Feature:
Feature 8G Platform Services Function:
unction PID management
Probability:
Probability Medium
Found in Release:
Release FOS6.3.1

Defect ID:
ID DEFECT000290556 Technical Severity:
Severity Medium
Summary:
Summary Host fails to discover LUNs when more than 64 LUNs are added to BES from Storage Array
Symptom:
Symptom The host which implements strict FCP/FCP-2 protocol frame fields checking for EOF delimiter will
not detect LUNs when more than 64 LUNs are added to BES from storage array. This also
impacts FS8-18 blades.
Feature:
Feature Data Security Function:
Function Disk Encryption
Probability:
Probability Medium
Found in Release:
Release FOS6.3.0 Service Request ID:
ID 426663

Fabric OS v6.3.1c Release Notes v1.0 Page 39 of 84

 Closed with Code Change in Fabric OS v6.3.1b

Defect ID:
ID DEFECT000298120 Technical Severity:
Severity Medium
Summary:
Summary Port based routing frame were out of order when FCP image pairs concurrently initiate
exchanges as originators over GE ports
Symptom
Symptom:
ptom 3rd party device has very poor performance over FCIP link between two Brocade 7800 over 1G
GE port. Same issue applies to FX8-24 blades.
Feature:
Feature FCIP Function:
Function FCIP Performance
Probability:
Probability Medium
Found in Release:
Release FOS6.3.1 Service Request ID:
ID 429767

Fabric OS v6.3.1c Release Notes v1.0 Page 40 of 84

Closed with Code Change in Fabric OS v6.3.1a
This section lists the defects with Critical, High and Medium Technical Severity closed with a code change as
of February 26, 2010 in Fabric OS v6.3.1a.

Defect ID:
ID DEFECT000249582 Technical Severity:
Severity High
Summary:
Summary DPC crash caused Brocade 7600 or FA4-19 blade goes to faulty.
Symptom:
Symptom When BP is rebooted in a middle of a PCI access cycle, the PCI cycle is not getting terminated
properly. This result in a DPC crash. Customer could see Brocade 7600 or FA4-18 reports faulty
during boot and raslog BL-1020 indicated switch timing out while initializing ASIC chips.
Feature:
Feature FA4-18 Platform Services Function:
Function 1250: ANZIO DRIVER
Probability:
Probability Low
Found in Release:
Release FOS6.2.0

Defect ID:
ID DEFECT000272207 Technical
Technical Severity:
Severity High
Summary:
Summary Enhancement request to add a user selectable parameter to adjust SFP polling during high CPU
load situation.
Symptom:
Symptom The new parameter is under System category of configurechassis CLI: %> configurechassis
Configure... System (yes, y, no, n): [no] y system.cpuLoad: (10..121) [121] 20 Default is 121,
represent CPU instantaneous load average of 1.21, first number in load average in uptime or top
command. So by default, CPU will poll sfp when load is 1.21 or lower. Use this parameter to
adjust SFP polling to avoid laser fault condition [C2-5678] causes links to reset under high CPU
load.
Feature:
Feature Field Escalation Function:
Function OS: Infrastructure
Probability:
Probability High
Found in Release:
Release FOS6.2.1 Service Request ID:
ID 409677

Defect ID:
ID DEFECT000277488 Technical Severity:
Severity High
Summary:
Summary Observed ASSERT - Failed expression: fabSysDynamicAreaSupported(sw->sw_inst) after
firmwarecommit
Symptom:
Symptom Observed HAM-1007 and HAM-1009 MANUALLY REBOOT the system for recovery - auto-reboot
is disabled. Sometime both CPs fail and switch cannot boot up. This happens only when a
configuration file for dynamic area mapping is corrupted which is very rare.
Workaround:
Workaround Remove the port2Bound file in /etc/fabos/port2Bound files in both active CP and standby
CPs, also in both partitions on both CP, after that, reboot the switch.
Feature:
Feature 8G Platform Services Function:
Function FOS Kernel Drivers
Probability:
Probability Low
Found in Release:
Release FOS6.4.0

Fabric OS v6.3.1c Release Notes v1.0 Page 41 of 84

 Closed with Code Change in Fabric OS v6.3.1a

Defect ID:
ID DEFECT000280165 Technical Severity:
Severity High
Summary:
Summary Switch detected termination of daemons due to bad EOFa frames are forward to application
rather than dropped in 8G driver
Symptom:
Symptom Under rare situation (such as marginal hardware), switch may see corrupted EOF frames
forwarded to CPU for processing. 8G driver did not drop such frame and passed to upper layer
application demons. This can cause switch panic or hafailvoer.
Feature:
Feature 8G Platform Services Function:
Function FOS Kernel Drivers
Probability:
Probability Low
Found in Release:
Release FOS6.4.0

Defect ID:
ID DEFECT000282795 Technical Severity
Severity:
verity High
Summary:
Summary Host failed to discover tapes due to a VI/VT database mismatch between the switches that are
part of the same Encryption Group
Symptom:
Symptom Host will not able to discovery Tape devices that are part of the same EG
Workaround:
Workaround Issue "cryptocfg --commit" again to sync up the VT/VI database across nodes in the EG.
Feature:
Feature Data Security Function:
Function Tape Encryption
Probability:
Probability Low
Found in Release:
Release FOS6.3.1
Where Else Fixed: FOS6.3.1, FOS6.3.0 c

Defect ID:
ID DEFECT000283046 Technical Severity
Severity:
everity High
Summary:
Summary GID_PN from a VI for any other Virtual Entity instantiated on the same port (same area) succeeds
even though the entities are not zoned with VI
Symptom:
Symptom Zoning restriction did not work for NPIV/loop ports when one device tries to get other device
information on the same port using name based queries (GID_PN, GID_NN). This could cuase
SAS attempt to talk to devices fail.
Feature:
Feature SAS Function:
Function VI
Probability:
Probability High
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000269189 Technical Severity:
Severity Medium
Summary:
Summary SERDES tuning values to support BR–804 HBA
Symptom:
Symptom Fine tune SERDES value for BR–804 HBA support. This change only applies to Brocade 5480
platform.
Workaround:
Workaround No
Feature:
Feature Embedded Platform Services Function:
Function Bulova
Probability
Probability:
ility Medium
Found in Release:
Release FOS6.3.0

Fabric OS v6.3.1c Release Notes v1.0 Page 42 of 84

 Closed with Code Change in Fabric OS v6.3.1a

Defect ID:
ID DEFECT000270261 Technical Severity:
Severity Medium
Summary:
Summary CP/switch fails to boot on DCX, DCX-4s and Brocade 5300.
Symptom:
Symptom CP does not boot on power up or fails during hafailover with CF access error; "HDA: drive not
ready" message sometimes are seen on console.
Workaround:
Workaround Reboot switch again
Feature:
Feature OS Services Function:
Function Linux Kernal
Probability:
Probability Low
Found in Release:
Release FOS6.2.0

Defect ID:
ID DEFECT000272847 Technical Severity:
Severity Medium
Summary:
Summary 8-bit area address is not properly range checked
Symptom:
Symptom Firmware upgrade may fail with segment fault from FOS 6.3.x to a future FOS release when there
is multiple LS non-continuous switch instances.
Feature:
Feature Quattro Function:
Function Kernel Driver
Probability:
Probability Medium
Found in Release:
Release FOS6.4.0

Defect ID:
ID DEFECT000279687 Technical Severity:
Severity Medium
Summary:
Summary Switch panic after detecting termination of process webd:1130
Symptom:
Symptom Perform multiple configdownload through DCFM or CLI can trigger memory issues with webd.
most time webd will restart and at time this could trigger switch panic.
Feature:
Feature Field Escalation Function:
Function Web Management
Probability:
Probability Low
Found in Release:
Release FOS6.2.1 Service Request ID:
ID 416939

Defect ID:
ID DEFECT000279834 Technical Severity:
Severity Medium
Summary:
Summary Encountered "(SAS) Application installation failed. Switch does not support SAS." message on
Brocade 7600 when upgrade/downgrade SAS
Symptom:
Symptom SAS upgrade fails with "(SAS) Application installation failed. Switch does not support SAS."
message. This happens when a race condition triggers a CLI (slotshow) that firmwaredownload
relies fails.
Workaround:
Workaround Try firmwaredownload again to upgrade SAS when it fails
Feature:
Feature FIRMWARE DOWNLOAD Function:
Function Firmware Download
Probability:
Probability Medium
Found
Found in Release:
Release FOS6.3.1

Fabric OS v6.3.1c Release Notes v1.0 Page 43 of 84

 Closed with Code Change in Fabric OS v6.3.1a

Defect ID:
ID DEFECT000283300 Technical Severity:
Severity Medium
Summary:
Summary TCP connection is torn down prematurely.
Symptom:
Symptom Failure to clean up the locally managed socket caused application to read from stale sockets
and drop the TCP connection. This only impact encryption platforms (BES, FS8-18)
Feature:
Feature Data Security Function:
Function HA Cluster
Probability:
Probability Medium
Found in Release:
Release FOS6.3.1

Defect ID:
ID DEFECT000283740 Technical Severity:
Severity Medium
Summary:
Summary Host hangs while scanning LUNs.
Symptom:
Symptom Customer can scan 2 cleartext LUNs (0 and 1) but cannot scan encrypted LUNs 2-7 on some
device types.
Feature:
Feature Field Escalation Function:
Function Encryption
Probability:
Probability Low
Found in Release:
Release FOS6.3.0 Service Request ID:
ID 421053

Defect ID:
ID DEFECT000284472 Technical Severity:
Severity Medium
Summary:
Summary SCR is not properly registered in the name server
Symptom:
Symptom After upgrade from FOS v6.2.x to FOS v6.3.0x or FOS v6.3.1, reboots/bounce a target port,
RSCNs are not sent to all devices the target is zoned with. Hosts are unable to see the target
until all hosts port are bounced. This defect only happened with FOS v6.3.x upgrade. It impacts
all platforms with FC ports, both Ficon and non-ficon enviorment.
Workaround:
Workaround need to bounce port to recover, or upgrade to the version with fix
Feature:
Feature Field Escalation Function:
Function Fabric Services
Probability:
Probability High
Found in Release:
Release FOS6.3.0 Service Request ID:
ID 421925

Defect ID:
ID DEFECT000285251 Technical Severity:
Severity Medium
Summary:
Summary DPC Online event is not delivered to storage application due to a timer issue
Symptom:
Symptom DPC-0 Online is not delivered to Storage Application. This applies to FA4-8 and AP7600 only.
Feature:
Feature FA4-18 Platform Services Function:
Function Blade FOS SW
Probability:
Probability High
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000285372 Technical Severity:
Severity Medium
Summary:
Summary VI/VTs goes OFFLINE post a DPC crash.
Symptom:
Symptom In a rare DPC crash case, RSCN was not sent out in time, caused VI/VT goes offline. This is
limited to FA4-18 and AP7600 platforms.
Feature:
Feature FA4-18 Platform Services Function:
Function 1250: OS SUPPORT
Probability:
Probability Medium
Found in Release:
Release FOS6.4.0

Fabric OS v6.3.1c Release Notes v1.0 Page 44 of 84

Closed with Code Change in Fabric OS v6.3.1
This section lists the defects with Critical, High and Medium Technical Severity closed with a code change as
of January 22, 2010 in Fabric OS v6.3.1.

Defect ID:
ID DEFECT000279946 Technical Severity:
Severity Critical
Summary:
Summary Customer unable to remove Admin domains, SFC rejected errors sent by AD3
Symptom:
Symptom When execute command cfgdisable, gets the following message:Too many devices found
(>120) in default zone.
Workaround:
Workaround 1. Migrated all devices to AD0 before as outlined in the AD migrate instructions. 2. Remove
the devices from the ADs using the: ad --select 255 ad --remove <ADnum> -d “<devices to
remove separated by semicolon>” ad --apply 3. Perform ‘ad --clear –f’ followed by ‘ad --apply’
from the AD255 context and this should remove the ADs properly.
Feature:
Feature Field Escalation Function:
Function Fabric Services
Probability:
Probability Medium
Found in Release:
Release FOS6.2.0 Service Request ID:
ID 412409

Defect ID:
ID DEFECT000240850 Technical Severity:
Severity High
Summary:
Summary With SNMP severity set to 3, the DCX sends out traps when a core blade is inserted, but not
when it is removed
Symptom:
Symptom Traps not sent out when a core blade is removed and SNMP severity set to 3
Feature:
Feature Field Escalation Function:
Function Management Services
Probability:
Probability Medium
Found in Release:
Release FOS6.1.0 Service Request ID:
ID 361769

Defect ID:
ID DEFECT000260338 Technical Severity:
Severity High
Summary:
Summary After blade fault, port was taken off line at ASIC level but offline SCN was not sent to
applications such as routing module, fspfd, fabric which created an inconsistent view between
application and kernel on the port state of the faulted blade.
Symptom:
Symptom After a blade fault, a replacement blade would fault due to frame count mismatch during POST,
as there are still frames sent to offline port by upper layer application, fabric unstable as fabric
attempts to build fabric through offline port, and hosts connected to the replacement blade
have problem logging back into the fabric with "Switch not ready for F or L port" message.
Feature:
Feature Field Escalation Function:
Function ASIC Driver
Probability:
Probability Low
Found in Release:
Release FOS6.2.0 Service Request ID:
ID 391827
Where Else Fixed: FOS6.2.2

Fabric OS v6.3.1c Release Notes v1.0 Page 45 of 84

 Closed with Code Change in Fabric OS v6.3.1

Defect ID:
ID DEFECT000261638 Technical
Technical Severity:
Severity High
Summary:
Summary TI zones become disabled when telnet times out following TI zone change
Symptom:
Symptom Set telnet timeout to 1 minute, logout/login to have timeout take effect, created new TI zone,
waited for telnet session to timeout, log back into switch and issue cfgsave; cfgsave actually
pushes data, which shouldn't occur as the session timed out. Without properly terminating stale
transaction before processing a new TI zone can result in erroneous TI zone properties list and
trigger other fabric-wide instability events such as no route, rtwr errors in fabric etc.
Feature:
Feature Field Escalation Function:
Function Fabric Services
Probability:
Probability Medium
Found in Release:
Release FOS6.1.1 Service Request ID:
ID 394553
Where Else Fixed: FOS6.2.2

Defect ID:
ID DEFECT000263300 Technical Severity:
Severity High
Summary:
Summary switchshow shows all PIDs the same after reboot
Symptom:
Symptom After switch came back up from reboot, nsshow was empty, all the PIDs are the same for all the
ports that all online, and all online ports have the same address due to recovery messed up
port to area map on pizza box for FOS 6.1->6.2->6.3 warm upgrade code path.
Feature:
Feature 8G Platform Services Function:
Function PID management
Probability:
Probability Low
Found in Release:
Release FOS6.3.0 Service Request ID:
ID 398903

Defect ID:
ID DEFECT000265158 Technical Severity:
Severity High
Summary:
Summary Under very uncommon Fabric Watch setting, Fabric Watch daemon can crash.
Symptom:
Symptom If fwalarms is turned off and Errlog is turned on in Fabric Watch configuration, Fabric Watch
daemon can crash and lead to switch panic.
Workaround:
Workaround In the threshold alarm matrix configuration for all port related thresholds, disable ErrLog and
Port Fencing (using fwconfigure) this will avoid the above functions from being called (on any
threshold events) and leaking or enable fwalarmsfilterset
Feature:
Feature Field Escalation Function:
Function Panic / OOM
Probability:
Probability Low
Found in Release:
Release FOS6.2.0 Service Request ID:
ID 398779
Where Else Fixed: FOS6.2.2

Defect ID:
ID DEFECT000267411 Technical Severity:
Severity High
Summary:
Summary Executing configdownload caused fcoed died
Symptom:
Symptom switch got rebooted
Feature:
Feature CEE-FCOE Function:
Function FCOE Daemon
Probability:
Probability Medium
Found in Release:
Release FOS6.3.0

Fabric OS v6.3.1c Release Notes v1.0 Page 46 of 84

 Closed with Code Change in Fabric OS v6.3.1

Defect ID:
ID DEFECT000267476 Technical Severity:
Severity High
Summary:
Summary Brocade 7800 panic during overnight workload
Symptom
Symptom: Brocade 7800 switch crashed and FCIP I/O stopped during overnight workload over 4G Tunnel
testing.
Feature:
Feature Striker/Spike Platform Services Function:
Function Blade Driver
Probability:
Probability Low
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000268714 Technical Severity
Severity:
verity High
Summary:
Summary ONMD is crashing continuously when the links were coming up
Symptom:
Symptom Saving the configuration with LLDP disabled leads to crash when switch rebooted
Feature:
Feature CEE-LAYER2 Function:
Function LLDP
Probability:
Probability High
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000269513 Technical Severity:
Severity High
Summary:
Summary Non-VF mode on DCX, enabled the F-Port Trunk and then enabled the Dynamic Area Addressing
mode, changing to DAA mode cause Trunk area to be disabled.
Symptom:
Symptom Check F-Port Trunk using "porttrunkarea --show enabled", it returned "No ports have Trunk Area
enabled" and there was no F-Port TRUNK anymore.
Feature:
Feature 8G Platform Services Function:
Function Other
Probability:
Probability Low
Found in Release:
Release FOS6.4.0

Defect ID:
ID DEFECT000269997 Technical Severity:
Severity High
Summary:
Summary Cascaded CUP failure when channel on Brocade 48000 8G blade and E Port is on different chip
Symptom:
Symptom no cascaded CUP connectivity when channel on Brocade 48000 8G blade and E port are on
different ASIC chip.
Feature:
Feature 8G ASIC Driver Function
Function:
on C2 ASIC driver
Probability:
Probability High
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000270038 Technical Severity:
Severity High
Summary:
Summary Daemon crash on logical switch creation-deletion
Symptom:
Symptom Fabric daemon panic due to the shared memory info got corrupted during logical switch
creation-deletion testing loop.
Feature:
Feature FC Services Function:
Function Zoning
Probability:
Probability Low
Found in Release:
Release FOS6.3.0

Fabric OS v6.3.1c Release Notes v1.0 Page 47 of 84

 Closed with Code Change in Fabric OS v6.3.1

Defect ID:
ID DEFECT000270373 Technical Severity:
Severity High
Summary:
Summary On Brocade 7800, no NPIV devices (including AG) can log into ports in the first quad of FR4-18
blade /Brocade 7500
Symptom:
Symptom The AG port gets disabled with a message stating NPIV not supported on Fabric port although
NPIV is enabled on the 7800 ports. The same NPIV based device logs in as expected with the
FLOGIs + FDISCs in any other port from 4-31.
Feature:
Feature 4G Platform Services Function:
Function FOS Kernel Drivers
Probability:
Probability Medium
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000270813 Technical Severity:
Severity High
Summary:
Summary Switch is not accessible through Web Tools after firmware upgrade to FOS v6.3.0a
Symptom:
Symptom After upgrade from v6.2.x to v6.3.x Web Tools cannot be accessed via name or across a NAT
network connection. In either instance the following message is displayed; Not a Management
IP Address, The IP address given is not one of the management addresses. Use 10.100.2.108 .
With NAT the real address of the switch is displayed. On a non-NAT environment access via IP
address works. Access via Switchname gets the same response again displaying the switch ip
address.
Workaround:
Workaround Access switch via IP address
Feature:
Feature Mgmt Embedded - HTTP Function:
Function Other
Probability:
Probability High
Found in Release:
Release FOS6.3.0 Service Request ID:
ID 408403

Defect ID:
ID DEFECT000271111 Technical Severity:
Severity High
Summary:
Summary RTWR messages are logged when more than 16 dynamic paths are setup to remote domains
Symptom:
Symptom On Brocade 5300, 300, and 8G embedded switches, when more than 16 dynamic path routes
are set up to remote switches, it is possible that parity errors can be generated by the switch
and indicated by internal raslog C2-5658. Customer can experience path loss and traffic
interruption.
Workaround:
Workaround Limit the number of dynamic paths on these platforms. Note: if there are more than 16
dynamic paths already on these platforms, upgrade to the fixed release could be a cold
recovery
Feature:
Feature Field Escalation Function:
Function Fabric Services
Probability:
Probability Medium
Found in Release:
Release FOS6.2.1 Service Request ID:
ID 406617

Fabric OS v6.3.1c Release Notes v1.0 Page 48 of 84

 Closed with Code Change in Fabric OS v6.3.1

Defect ID:
ID DEFECT000273098 Technical Severity:
Severity High
Summary:
Summary Response time for small read request between FCIP connection takes over 10 msec.
Symptom:
Symptom Observe 2-4ms delay between the time something arrives on the GE port until its sent out the
FC port
Workaround:
Workaround Do not run low IO rate traffic. Only occurs when low IO rate traffic is passing through the FCIP
Tunnel.
Feature:
Feature FCIP Function:
Function FCIP I/O
Probability:
Probability Low
Found in Release:
Release FOS6.3.0 Service Request ID:
ID 409943

Defect ID:
ID DEFECT000273131 Technical Severity:
Severity High
Summary:
Summary FCOE10-24 getting into Faulty (21) mode during stress testing.
Symptom:
Symptom Backend port fault triggered blade fault with raslog: [EM-1034], 22744, SLOT 4 | CHASSIS,
ERROR, , Slot 2 set to faulty, rc=20015.
Feature:
Feature CEE-Infrastructure Function:
Function ANVIL DRIVER
Probability:
Probability Low
Found in Release:
Release FOS6.4.0

Defect ID:
ID DEFECT000273514 Technical Severity:
Severity High
Summary:
Summary FC FastWrite host cannot see target after target port bounce due to cam setup problem on
backend port used by FC FastWrite
Symptom:
Symptom Not able to recover FC FastWrite paths after device maintenance was performed, or remote
target port is bounced.
Feature:
Feature Field Escalation Function:
Function FCIP Flipper/ASIC
Probability:
Probability Medium
Found in Release:
Release FOS6.2.0 Service Request ID:
ID 410681
Where Else Fixed: FOS6.2.2 a

Defect ID:
ID DEFECT000275630 Technical
Technical Severity:
Severity High
Summary:
Summary DCX crashed while attempting to change TE Port from LAG to trunk mode
Symptom:
Symptom When port is changed from standard mode LAG to trunk port, the switch crashed due to ssmd
core dump.
Feature:
Feature CEE-SYSTEM SERVICES Function:
Function SSM
Probability
Probability:
obability High
Found in Release:
Release FOS6.4.0

Fabric OS v6.3.1c Release Notes v1.0 Page 49 of 84

 Closed with Code Change in Fabric OS v6.3.1

Defect ID:
ID DEFECT000277444 Technical Severity:
Severity High
Summary:
Summary Switch may panic after executing fcplunquery or iscsicfg CLI command for tgt entity on FC4-
16IP.
Symptom:
Symptom FCPd termination occurred if PRLI or Report LUN query timeout during fcplunquery/iscsicfg CLI
and LOGO response comeback without a message queue to process it. This only impacts FOS
v6.2.2 and FOSv6.3.0c
Feature:
Feature FC Services Function:
Function FCP
Probability:
Probability Low
Found in Release:
Release FOS6.4.0
Where
Where Else Fixed: FOS6.2.2 a

Defect ID:
ID DEFECT000277814 Technical Severity:
Severity High
Summary:
Summary FCOE10-24 blade installed in the highest slot in a chassis based system does not send out UA's
(unsolicited advertisements)
Symptom:
Symptom FCOE10-24 blade installed in highest slot is up and running but will not support any FCoE
because there is no UA's being transmitted from the blade
Workaround:
Workaround Install FCOE10-24 to lower slot
Feature:
Feature CEE-FCOE Function:
Function FCOE PROTOCOL
Probability:
Probability High
Found in Release:
Release FOS6.3.0

Defect
Defect ID:
ID DEFECT000278788 Technical Severity:
Severity High
Summary:
Summary Switch displays incorrect information upon userconfig --show command execution
Symptom:
Symptom changes to the admin password on a switch are not being recorded properly. - Specifically the
"Password Last Change Date" shows incorrect date (1 day off).
Feature:
Feature UNDETERMINED Function:
Function UNDER REVIEW
Probability:
Probability Low
Found in Release:
Release FOS6.2.0 Service Request ID:
ID 416529

Defect ID:
ID DEFECT000244679 Technical Severity:
Severity Medium
Summary:
Summary Fabric Watch SFP messages logged invalid value
Symptom:
Symptom I2C read values of 0xFF and I2C NACK error case are not properly handled caused
improbable/unpredictable values to be reported by Fabric Watch on SFP.
Feature:
Feature Field Escalation Function:
Function EM / Hil / Sysctrl
Probability:
Probability Low
Found in Release:
Release FOS6.1.1 Service Request ID:
ID 370901

Fabric OS v6.3.1c Release Notes v1.0 Page 50 of 84

 Closed with Code Change in Fabric OS v6.3.1

Defect ID:
ID DEFECT000252641 Technical Severity:
Severity Medium
Summary:
Summary Configdownload doesn't load the tstimezone info.
Symptom:
Symptom Setup tstimezone, upload the configuration to a ftp server. After changing the tzh and tzm in the
config.txt file to a new value, and running configdownload to put the config.txt file on the switch.
Issue tstimezone command, the timezone is not changed.
Workaround:
Workaround Setup tstimezone through CLI.
Feature:
Feature Fabric Infrastructure Function:
Function Time Server
Probability:
Probability High
Found in Release:
Release FOS6.3.0
Where Else Fixed: FOS6.2.2

Defect ID:
ID DEFECT000254565 Technical Severity:
Severity Medium
Summary:
Summary After upgrade to FOSv6.x, script fails due to rsh switch with user account credential and
execute command "ifmodeshow" output errors and inaccurate output.
Symptom:
Symptom Telnet works, rsh with root credential work, only rsh using user credential gets "ifmodeshow
eth0": ioctl(ETHTOOL_GSET) failed.
Workaround:
Workaround Set suid permissions for ethmode: chmod +s /fabos/libexec/ethmode
Feature:
Feature Field Escalation Function:
Function OS: Linux
Probability:
Probability Medium
Found in Release:
Release FOS6.0.1 Service Request ID:
ID 382985
Where Else Fixed: FOS6.2.2

Defect ID:
ID DEFECT000258327 Technical Severity:
Severity Medium
Summary:
Summary 4G SFPs do not consistently show data in sfpshow on Brocade 7800 GbE ports
Symptom:
Symptom 4G SFP data is not shown on Brocade 7800 GbE ports, sfpshow reports"Cannot read serial
data", or correct sfp serial number or 'nothing at all'.
Feature:
Feature Striker/Spike Platform Services Function:
Function BCM Driver
Probability:
Probability Medium
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000258330 Technical Severity:
Severity Medium
Summary:
Summary EX_Port Rejected Fabric Binding for Edge Fabric in IM3
Symptom:
Symptom Fabric binding will not work in 239 domain mode in IM3 with FCR
Feature:
Feature 8G FCR Function:
Function FCR Security
Probability:
Probability Low
Found in Release:
Release FOS6.3.0
Where Else Fixed: FOS6.2.2

Fabric OS v6.3.1c Release Notes v1.0 Page 51 of 84

 Closed with Code Change in Fabric OS v6.3.1

Defect ID:
ID DEFECT000260099 Technical Severity:
Severity Medium
Summary:
Summary Support auto-assignment of slot-Based licenses and address slot based license issues
Symptom:
Symptom slot based license feature is enhanced.
Feature:
Feature License Function:
Function License
Probability:
Probability Low
Found in Release:
Release FOS6.4.0

Defect ID:
ID DEFECT000260552 Technical Severity:
Severity Medium
Summary:
Summary Fabric Watch messages logged with values above 100%.
Symptom:
Symptom Fabric Watch FW-1186 & FW1190 messages are being logged with percentages above 100%,
which is not possible. This is likely to happen during the first Fabric Watch polling cycle after
slotstatsclear command has been issued.
Feature:
Feature Field Escalation Function:
Function Management Services
Probability:
Probability Low
Found in Release:
Release FOS6.2.0 Service Request ID:
ID 384439
Where Else Fixed: FOS6.2.2

Defect ID:
ID DEFECT000260572 Technical Severity:
Severity Medium
Summary:
Summary Zone changes of Fabric Class does not work
Symptom:
Symptom 'Zoning Changes' of 'Fabric class areas' in fwconfigure does not function correctly
Feature:
Feature Fabric Infrastructure Function:
Function Fabric Watch
Probability:
Probability Low
Found in Release:
Release FOS6.3.0
Where Else Fixed: FOS6.2.2 a

Defect ID:
ID DEFECT000260700 Technical Severity:
Severity Medium
Summary:
Summary Unable to load IF.mib and SW.mib in AdventNet MIB Browser
Symptom:
Symptom The user will not be able to load IF.mib and SW.mib
Feature:
Feature Mgmt Embedded - SNMP Function:
Function Other
Probability:
Probability High
Found in Release
Release:
ase FOS6.3.0

Defect ID:
ID DEFECT000261246 Technical Severity:
Severity Medium
Summary:
Summary HA synchronization lost after a switch with trunk ports panic and manual reboot was needed to
recover.
Symptom:
Symptom After hafailover, HA component did not get fabric stable due to race condition with trunk ports
dropping EFP response. This condition is rare but if it happens, manual reboot is needed to
recover.
Feature:
Feature Field Escalation Function:
Function Management Services
Probability:
Probability Low
Found in Release:
Release FOS6.2.0 Service Request ID
ID: 393141

Fabric OS v6.3.1c Release Notes v1.0 Page 52 of 84

 Closed with Code Change in Fabric OS v6.3.1

Defect ID:
ID DEFECT000261663 Technical Severity:
Severity Medium
Summary:
Summary Clean up printf to eliminate error and error message: "ssnGet: Unable to get WWN info.sw=0
rc=-5"
Symptom:
Symptom The following message may pop up to console while firmware is in process of committing:
"ssnGet: Unable to get WWN info.sw=0 rc=-5".
Feature:
Feature System Controls/EM Function:
Function DCX/DCX-4S
Probability:
Probability Medium
Found in Release:
Release FOS6.3.0
Where Else Fixed: FOS6.2.2

Defect ID:
ID DEFECT000262942 Technical Severity:
Severity Medium
Summary:
Summary Faulty CP is not displayed in Web Tools
Symptom:
Symptom The display of the CP blade disappears from Web Tools when the CP blade became faulty.
Feature:
Feature WebMgmt Function:
Function Switch Explorer/Switch View
Probability:
Probability Medium
Found in Release:
Release FOS6.2.0 Service Request
Request ID:
ID 399755

Defect ID:
ID DEFECT000263500 Technical Severity:
Severity Medium
Summary:
Summary After using ipaddrset, incorrect CP hostname is displayed on standby CP
Symptom:
Symptom Login prompt of StandbyCP show incorrectly after set Host name of CP Blade by ipaddrset -cp
command
Feature:
Feature Field Escalation Function:
Function OS: Infrastructure
Probability:
Probability High
Found in Release:
Release FOS6.2.1 Service Request ID:
ID 399361
Where Else Fixed: FOS6.2.2 a

Defect ID:
ID DEFECT000263704 Technical Severity:
Severity Medium
Summary:
Summary Byte Streaming support on 7500/FR4-18i does not work with 3rd party Optimizers
Symptom:
Symptom 1250 panics when running byte streaming code when connected through a 3rd party optimizer.
Feature:
Feature Legacy FCIP (7500/FR4-18i) Function:
Function FCIP I/O
Probability:
Probability Low
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000263889 Technical Severity:
Severity Medium
Summary:
Summary Brocade 200E and 4G based embedded platform speed negotiation fails when lock port as
G_Port
Symptom:
Symptom Switch port cannot come on line when reboot connected server sometimes. This applies to
Brocade 200E and 4G embedded platforms only.
Feature:
Feature Field Escalation Function:
Function ASIC Driver
Probability:
Probability Low
Found in Release:
Release FOS6.2.1 Service Request ID:
ID 400493
Where Else Fixed: FOS6.2.2

Fabric OS v6.3.1c Release Notes v1.0 Page 53 of 84

 Closed with Code Change in Fabric OS v6.3.1

Defect ID:
ID DEFECT000263930 Technical Severity:
Severity Medium
Summary:
Summary portbeacon command is not found
Symptom:
Symptom User cannot turn on/off port beacon on FOS v6.3.0x
Feature:
Feature 4G Platform Services Function:
Function Sys-Control/Environment Monitor
Probability:
Probability High
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000264548 Technical Severity:
Severity Medium
Summary:
Summary CALD failed, but no failover happened – cald stuck as <defunct>
Symptom:
Symptom CALD panic occurred at customer site, CPs became out of sync, and a manual reboot was
required of the active CP to recover. The ps output still contains cald, however it is in a
<defunct> state. 4 0 30056 2497 16 0 0 0 - Z ? 0:01 \_ cald <defunct>
Workaround:
Workaround Manually reboot.
Feature:
Feature Field Escalation Function:
Function Management Services
Probability:
Probability Low
Found in Release:
Release FOS6.2.0 Service Request ID
ID: 400805
Where Else Fixed: FOS6.2.2

Defect ID:
ID DEFECT000265119 Technical Severity:
Severity Medium
Summary:
Summary Rebooting backbone host is unable to discover common zone target in the edge fabric.
Symptom:
Symptom Timing window exists where a SID zone miss could drop a frame. Initiator that does not retry
PLOGI will fail to discover targets of edge fabric.
Workaround:
Workaround Workaround (recovery) is to disable/enable the target.
Feature:
Feature Striker/Spike Platform Services Function:
Function VEX
Probability:
Probability Medium
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000265165 Technical Severity:
Severity Medium
Summary:
Summary DCX/DCX-S4 experiences repeat assert panic on emd during high temperature testing.
Symptom:
Symptom During power off/on switch test with DCX/DCX-4S under stressed environment condition, switch
experienced panic rather than blade fault. This could happen when blades get too hot, or there
is a bad temperature sensor, or a spurious sensor reading.
Feature:
Feature Field Escalation Function:
Function EM / Hil / Sysctrl
Probability:
Probability Low
Found in Release:
Release FOS6.2.0

Fabric OS v6.3.1c Release Notes v1.0 Page 54 of 84

 Closed with Code Change in Fabric OS v6.3.1

Defect ID:
ID DEFECT000265327 Technical Severity:
Severity Medium
Summary:
Summary Observe C2-5464/5465 errors every time power cycling switch with FCoE ports.
Symptom:
Symptom Cold reboot switch, observe internal raslog flood due logical port to FCoE virtual user port
mapping error.
Feature:
Feature 8G ASIC Driver Function:
Function C2 ASIC driver
Probability:
Probability Medium
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000265647 Technical Severity:
Severity Medium
Summary:
Summary Bottleneck configurations are not backed up in AG
Symptom:
Symptom Configuration back up on AG does not have the bottleneck configurations.
Feature:
Feature FC Services Function:
Function Bottleneck Management
Probability:
Probability Low
Found in Release:
Release FOS6.4.0

Defect ID:
ID DEFECT000265865 Technical Severity:
Severity Medium
Summary:
Summary ARB(ff) usage as fill words for 8Gb connectivity does not abide by the standards
Symptom:
Symptom IDLE/ARBFF mode 2 is now available and added mode 3 which will perform mode 1
(ARBF/ARBFF) via hardware state machine; Depends on device behavior, different modes are
configurable.
Feature:
Feature 8G ASIC Driver Function:
Function ASIC Driver
Probability:
Probability Low
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000267596 Technical Severity:
Severity Medium
Summary:
Summary When port cfgdefault is issued on VE port, error messages are POSTED on DP and CP
Symptom:
Symptom portcfgdefault 4/22: Port 182 NPIV Limit Set to 126! Unknown Error
Workaround:
Workaround Do not issue the portCfgDefault command on FX8-24/7800 VE ports.
Feature:
Feature FCIP Function:
Function FCIP Port
Probability:
Probability Medium
Found in Release:
Release FOS6.4.0

Defect ID:
ID DEFECT000267637 Technical Severity
Severity:
ity Medium
Summary:
Summary Access Gateway responding to misdirected LOGO on 48-port blade.
Symptom:
Symptom When AG switch is connecting to a secondary port on FC4-48 or FC8-48. If the primary port
goes down, some frames might be wrongly routed to the AG switch's secondary port, AG
respond to these frame with ACC rather than drop.
Workaround:
Workaround Do not put AG switch at the secondary port on 48-port blades
Feature:
Feature Field Escalation Function:
Function Access Gateway
Probability:
Probability Low
Found in Release:
Release FOS6.1.1 Service Request ID:
ID 404527

Fabric OS v6.3.1c Release Notes v1.0 Page 55 of 84

 Closed with Code Change in Fabric OS v6.3.1

Defect ID:
ID DEFECT000268665 Technical Severity:
Severity Medium
Summary:
Summary During reboot, the NPIV device is sending the explicit logout. Switch does not clean up route
properly.
Symptom:
Symptom NPIV tape devices may not be seen by any of the hosts
Feature:
Feature FC Services Function:
Function NPIV
Probability:
Probability Low
Found in Release:
Release FOS6.3.0 Service Request ID:
ID 405453
Where Else Fixed: FOS6.2.2 a

Defect ID:
ID DEFECT000268808 Technical Severity:
Severity Medium
Summary:
Summary portlog parameters are not persistent after hafailover
Symptom
Symptom: After hafailover, the portlog parameters "debug" and "Portlog events enable" goes back to
default, or setting in previous reboot rather than the new setting before hafailover.
Feature:
Feature Infrastructure Function:
Function Config Download
Probability:
Probability Low
Found in Release:
Release FOS6.3.0 Service Request ID:
ID 405519

Defect ID:
ID DEFECT000268938 Technical Severity:
Severity Medium
Summary:
Summary After reboot Brocade 8000 switch, monitored flood of internal RASLOG message on FCOE/NPIV
port.
Symptom:
Symptom WWN entries are actually logged into the switch but observe flood of FCOE-5026 internal raslog
meesage as: WARNING, Brocade8000, fcoe_process_login_rsp: AVL entry deleted for WWN :
10:00:88:88:33:00:00:02 , fcoe_login.c, line 1840. No other functional impact.
Feature:
Feature CEE-FCOE Function:
Function FCOE DRIVER
Probability:
Probability Low
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000269267 Technical Severity:
Severity Medium
Summary:
Summary After upgrade from FOS v6.2.x to FOS v6.3.0b/c and then downgrade back down to FOSv6.2.0x,
observe critical message "BKSW-5002 " swd_drv.c, line: 1323
Symptom:
Symptom Observed kSWD: SWDIoctl: pid=480 request unknown IOCTL type 1074026240 after
downgrade due to a new file descriptor introduced in FOS v6.3.0b/c.
Feature:
Feature High Availability Function:
Function HA infrastructure
Probability:
Probability Medium
Found
Found in Release:
Release FOS6.3.0

Fabric OS v6.3.1c Release Notes v1.0 Page 56 of 84

 Closed with Code Change in Fabric OS v6.3.1

Defect ID:
ID DEFECT000269632 Technical Severity:
Severity Medium
Summary:
Summary FCIP tunnel bounce with impairment test..
Symptom:
Symptom Observe tunnel bounce while testing with following impairment test: * 100msec latency *
corrupt 1 byte in 1 frame in 200k * drop 1 frame in 500k frames
Workaround:
Workaround Identify and fix cause of TCP Network retransmissions. Reduce tunnel maximum data rate to
level that does not experience packet loss or corruption on the network.
Feature:
Feature FCIP Function:
Function FCP TCP/IP Stack
Probability:
Probability Low
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000269691 Technical Severity:
Severity Medium
Summary:
Summary Support for arrays that support SPC-2 - LSN identification
Symptom:
Symptom Some array, although it supports SPC-3 but indicates in the standard inquiry data that it
supports SPC-2. This causes the LUN to show up with a different LUN number on a different
path.
Feature:
Feature Data Security Function:
Function Disk Encryption
Probability:
Probability Low
Found in Release:
Release FOS6.4.0

Defect ID:
ID DEFECT000269935 Technical Severity
Severity:
rity Medium
Summary:
Summary Loop port takes long time to come up in IM2/IM3 mode
Symptom:
Symptom There is a time window during ELP process, it can cause a loop port to take more than 15 to 20
sec to come up
Feature:
Feature FC Services Function:
Function Fabric
Probability:
Probability Low
Found in Release:
Release FOS6.4.0

Defect ID:
ID DEFECT000270065 Technical Severity:
Severity Medium
Summary:
Summary Observed VE tunnel bounce after a hareboot on edge switch on Brocade 7800
Symptom:
Symptom iswitchd disable port due to fspf timeout prematurely during hafailover under heavy load.
Feature:
Feature 8G FCR Function:
Function FCR Daemon
Probability:
Probability Low
Found in Release:
Release FOS6.3.0

Fabric OS v6.3.1c Release Notes v1.0 Page 57 of 84

 Closed with Code Change in Fabric OS v6.3.1

Defect ID:
ID DEFECT000270325 Technical Severity:
Severity Medium
Summary:
Summary Switch no longer shows the error message to indicate an invalid zone name and enforcement of
64 characters on zone name is conflicting.
Symptom:
Symptom zonecreate 3zone2,"1,1" no longer report error. There is no other functional impact as the zone
is not enabled. cfgcreate/zonecreate is also updated to prevent the creation of a cfg/zone
name greater than with 64 chars but allow zone/alias names greater than 64 chars in the list.
Feature:
Feature Field Escalation Function:
Function Fabric Services
Probability:
Probability Low
Found in Release:
Release FOS6.2.1 Service Request ID:
ID 404027

Defect ID:
ID DEFECT000270381 Technical Severity:
Severity Medium
Summary:
Summary Configure terminal/config terminal 0 fails sometimes with message IMISH DEBUG CONNECT
Symptom:
Symptom When tests does '<telnet session open> => cmsh => configure terminal => <does some
configuration>=> <close telnet session>' sequence repeatedly to configure/unconfigure the
DUT, sometimes, the 'configure terminal' command fails, and the 'config' prompt was not
obtained.
Feature:
Feature CEE-MANAGEABILITY Function:
Function CLI
Probability:
Probability Low
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000270683 Technical Severity:
Severity Medium
Summary:
Summary LDAP 2008 support
Symptom:
Symptom User name/password authentication may fail.
Feature:
Feature FOS Security Function:
Function LDAP
Probability:
Probability Low
Found in Release:
Release FOS6.4.0
Where Else Fixed: FOS6.2.2 a

Defect ID:
ID DEFECT000272519 Technical Severity
Severity:
everity Medium
Summary:
Summary Change requirement to remove trial license before allowing non-trial license installation.
Symptom:
Symptom Customer need to remove trial licenses prior to installing permanent license for same feature.
Feature:
Feature License Function:
Function License
Probability:
Probability High
Found in Release:
Release FOS6.3.0

Fabric OS v6.3.1c Release Notes v1.0 Page 58 of 84

 Closed with Code Change in Fabric OS v6.3.1

Defect ID:
ID DEFECT000272635 Technical Severity:
Severity Medium
Summary:
Summary After setting the SNMPv3 by "snmpconfig --set snmpv3", the
"snmp.snmpv3Keys.*.usmPrivKeySize:" parameter does not begin from a new line
Symptom:
Symptom switch failed configDownload with following message: snmp.snmpv3Usm.0.usmPrivProtocol:6
Invalid Value. Process function of configdownload failed for filter snmp, lrc = -1
Feature:
Feature Field Escalation Function:
Function SNMP
Probability:
Probability High
Found in Release
Release:
ase FOS6.2.1 Service Request ID:
ID 405179
Where Else Fixed: FOS6.2.2 a

Defect ID:
ID DEFECT000273580 Technical Severity:
Severity Medium
Summary:
Summary "lscfg --show" on FS8-18 reports problem on port number higher than 15
Symptom:
Symptom “ASIC not ready” errors after the blade removal and insertion of the FS8-18 Blade. Obaserve
FW-5002 in internal raslog when this happens.
Feature:
Feature FC4-16IP Platform Services Function:
Function FC4-16IP Blade Driver
Probability:
Probability High
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000274458 Technical Severity:
Severity Medium
Summary:
Summary Handle command timeout for cvlm/cvlc commands and CAL call optimization to address
weblinker crash
Symptom:
Symptom Blade faulted and weblinker crash when blade is stressed with heavy IO and constant stats
gathering
Feature:
Feature Data Security Function:
Function Disk Encryption
Probability:
Probability Medium
Found in Release:
Release FOS6.4.0

Defect ID:
ID DEFECT000274882 Technical Severity:
Severity Medium
Summary:
Summary DCX doesn't output FW-1003/FW-1004 after hafailover/reboot if user sets fwsettocustom.
Symptom:
Symptom DCX could not output FW-1003/FW-1004 after hafailover/reboot if user sets the
fwsettocustom. This cause customer does not get notified on temperature etc event change
when it's over threshold value.
Feature:
Feature Field Escalation Function:
Function High Availability
Probability:
Probability High
Found in Release:
Release FOS6.2.2 Service Request ID:
ID 413945
Where Else Fixed: FOS6.2.2 a

Fabric OS v6.3.1c Release Notes v1.0 Page 59 of 84

 Closed with Code Change in Fabric OS v6.3.1

Defect ID:
ID DEFECT000275158 Technical Severity:
Severity Medium
Summary:
Summary Observed CALD panic in 256 ports switch after stress test switchdisable/switchenable
Symptom:
Symptom Switch panic observed when large number of F_Port has top talkers installed on the switch.
Feature:
Feature Mgmt Embedded - CAL Function:
Function Other
Probability:
Probability Medium
Found in Release:
Release FOS6.4.0

Defect ID:
ID DEFECT000275255 Technical Severity:
Severity Medium
Summary:
Summary ssmd is crashing when certain cli is executed
Symptom:
Symptom clearing counters of acl's whose name starts with numeric value or just a numeric value will
cause crashing of ssm. For example: sw0# clear counters access-list mac 2acl_std or
sw0#clear counters access-list mac 10 Now ssm will get crashed.
Feature:
Feature CEE-SYSTEM SERVICES Function:
Function ACL
Probability:
Probability Medium
Found in Release:
Release FOS6.3.1_cee

Defect ID:
ID DEFECT000277671 Technical Severity:
Severity Medium
Summary:
Summary FW-1434 message when systemverification or portloopbacktest run on DCX
Symptom:
Symptom During diag test, switch report: 2009/12/02-15:02:50, [FW-1434], 5, SLOT 7 | FID 128,
WARNING, sw0, Switch status change contributing factor Blade: 1 blade failures (MARGINAL).
Once diag test complete, Fabric Watch reports switch is healthy.
Feature:
Feature Field Escalation Function:
Function Management Services
Probability:
Probability High
Found in Release:
Release FOS6.2.2 Service Request ID:
ID 413595
Where Else Fixed: FOS6.2.2 a

Defect ID:
ID DEFECT000278326 Technical Severity:
Severity Medium
Summary:
Summary DCX 8-Link ICL license only brings up 4 Links when connected to DCX-4S
Symptom:
Symptom Based on the way the physical connections are made on an ICL between a DCX and DCX-4S,
only half of the expected E-Ports (links) are coming online when a 8-Link ICL license is installed.
Feature:
eature FC Services Function:
Function Fabric
Probability:
Probability Medium
Found in Release:
Release FOS6.4.0

Fabric OS v6.3.1c Release Notes v1.0 Page 60 of 84

Closed with Code Change in Fabric OS v6.3.0d
This section lists the defects with Critical, High and Medium Technical Severity closed with a code change as
of March 22, 2010 in Fabric OS v6.3.0d.

Defect ID:
ID DEFECT000274646 Technical Severity:
Severity High
Summary:
Summary Brocade 8000 installed with FOS v6.3.0 through v6.3.0c, v6.3.1 and v6.3.1a panics doing
firmwaredownload.
Symptom:
Symptom Switch panic reported during firmware download. This only applies to Brocade 8000s factory
installed with FOS v6.3.0 through v6.3.0c, v6.3.1 and v6.3.1a.
Workaround:
Workaround Before upgrading from FOS v6.3.0 through v6.3.0c, v6.3.1 or v6.3.1a, check if /dev/altera is
present in secondary partition. If not present, copy it from primary partition via "cp
/dev/altera /mnt/dev/altera".
Feature:
Feature CEE-Infrastructure Function:
Function Zues Driver
Probability:
Probability High
Found in Release:
Release FOS6.4.0

Defect ID:
ID DEFECT000283637 Technical Severity:
Severity High
Summary:
Summary During hot code load, HA recover time is very long.
Symptom:
Symptom Under race condition, when extensive writing to compact flash happens during hafailover,
observe long HA recover time on switch. This could cause link reset or frame drop when
connecting switch did not see credit being returned in time. This is observed more often in, but
not limited to, VF environment and connecting switch is operating under single virtual channel
credit model. It applies to both director and switch platforms.
Feature:
Feature Infrastructure Function:
Function PDM/PortCfg
Probability:
Probability Low
Found in Release:
Release FOS6.4.0

Defect ID:
ID DEFECT000286104 Technical Severity:
Severity High
Summary:
Summary Ports on the FC8-48 become persistently disabled after upgrading from FOS v6.2.x to FOS
v6.3.x.
Symptom:
Symptom After upgrading from FOS v6.2.x to FOS v6.3.x on systems with FC8-48 blades installed, VF
disabled and fmsmode enabled, all ports on the FC8-48 blades to become persistently disabled
without warning.
Workaround:
Workaround Manually re-enable ports, no other viable workaround at this time
Feature:
Feature Field Escalation Function:
Function FICON
Probability:
Probability High
Found in Release:
Release FOS6.3.0 Service Request ID:
ID 423415

Fabric OS v6.3.1c Release Notes v1.0 Page 61 of 84

 Closed with Code Change in Fabric OS v6.3.0d

Defect ID:
ID DEFECT000289029 Technical Severity:
Severity High
Summary:
Summary DCX reboots continuously as Access Gateway config file is corrupt on FOS v6.3.0x
Symptom:
Symptom Under very rare condition, access gateway configuration files are corrupted and caused switch
bring up to timeout. Switch is reboot repeatedly by HA manager in an attempt to recover switch
with raslog: [HAM-1007]…, Need to reboot the system for recovery, reason: System bring up
timed out, … [HAM-1008]…,Rebooting the system for recovery - auto-reboot is enabled, This only
applies to FOS v6.3.0x and non-AG platforms. It does not apply to FOS v6.3.1 and later, or Pre-
FOSv6.3.0 releases.
Workaround
Workaround:
rkaround Follow the procedure show below to remove the corrupted files and upgrade to a version of
FOS that incorporates a fix for this problem
1. Execute the following commands to stop the recover reboot process on both CPs
a. touch /etc/fabos/config/no_reboot_recover
b. touch /mnt/etc/fabos/config/no_reboot_recover
2. Execute the following commands remove the corrupted AG files on both CPs
a. rm /etc/fabos/persistent_NPIV_config
b. rm /mnt/etc/fabos/persistent_NPIV_config
3. Reboot the switch
4. After the switch comes back up use the commands list below to remove the recover file again
on both CPs.
a. rm /etc/fabos/config/no_reboot_recover
b. rm /mnt/etc/fabos/config/no_reboot_recover
5. Upgrade the switch to FOS v6.3.0d or v6.3.1 and later.
Feature:
Feature Access Gateway Services Function
Function:
tion Daemon
Probability:
Probability Low
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000270261 Technical Severity:
Severity Medium
Summary:
Summary CP/switch fails to boot on DCX, DCX-4s and Brocade 5300.
Symptom:
Symptom The CP or switch fails to reboot, boot up on power up or fails during hafailover. The following CF
access error message, "HDA: drive not ready" is usually seen on the console when this occurs.
Feature:
Feature OS Services Function:
Function Linux Kernal
Probability:
Probability Low
Found in Release:
Release FOS6.2.0
Where Else Fixed: FOS6.2.2 b, FOS6.3.1 a

Fabric OS v6.3.1c Release Notes v1.0 Page 62 of 84

 Closed with Code Change in Fabric OS v6.3.0d

Defect ID:
ID DEFECT000284472 Technical Severity:
Severity Medium
Summary:
Summary State Change Registration (SCR) value is not properly registered in the name server.
Symptom:
Symptom When performing a firmware upgrade from Fabric OS v6.2.x to Fabric OS v6.3.0 through v6.3.0c
or v6.3.1 the SCR registration inside the Name Server is lost at the time of upgrade. As a result,
devices attached to the upgraded switch are not notified of changes to other devices in common
zones or other changes to the zoning configuration. This impacts all platforms with FC ports in
both FICON and non-FICON environment.
Workaround:
Workaround There are no non-disruptive workarounds to correct this problem. The customers may choose
to perform the following disruptive action. Perform a portdisable/portenable on all the
affected ports within the zone. However, because of its disruptive nature, Brocade does not
recommend this procedure.
Feature:
Feature Field Escalation Function:
Function Fabric Services
Probability:
Probability High
Found in Release:
Release FOS6.3.0 Service Request
Request ID:
ID 421925
Where Else Fixed: FOS6.3.1 a

Fabric OS v6.3.1c Release Notes v1.0 Page 63 of 84

Closed with Code Change in Fabric OS v6.3.0c
This section lists the defects with Critical, High and Medium Technical Severity closed with a code change as
of December 18, 2009 in Fabric OS v6.3.0c.

Defect ID:
ID DEFECT000265272 Technical Severity:
Severity Critical
Summary:
Summary Brocade 48000 with FR4-18i cannot see new device across LSAN after upgrade from FOS v5.x
non-disruptively all the way to FOS v6.2.x.
Symptom:
Symptom Customer unable to bring new devices on line, bounce host port causes path lose between host
and target. internal raslog has: [BL-5238], , Pinball Consistency check failure: error = -2, rsc = 1,
data1 = -1, data2 = 11, OID:0x43310881, marathon_fcr.c, line: 2296, comp:emd,
ltime:2009/09/17-18:47:02:676934; This only applies 4G routers and problem only shows
after upgrade to FOS v6.2.x.
Feature:
Feature Field Escalation Function:
Function ASIC Driver
Probability:
Probability High
Found in Release:
Release FOS6.2.0 Service Request ID:
ID 402497
Where Else Fixed:
Fixed FOS6.2.2

Defect ID:
ID DEFECT000270541 Technical Severity:
Severity Critical
Summary:
Summary On DCX, FCR fails to route traffic on 8G EX ports after code upgrade from FOS v6.1 to FOS v6.2,
followed by hafailover and ports activities
Symptom:
Symptom DCX running FOS v6.1 with 8G EX ports (Integrated routing, IR) as pre-condition, upgrade to
FOSv6.2 based code, if there is additional hafailover, then add new device, bounce device ports
could trigger route problem, cause host cannot see device.
Feature:
Feature Field Escalation Function:
Function FCR
Probability:
Probability High
Found in Release
Release: FOS6.2.0 Service Request ID:
ID 409197
Where Else Fixed: FOS6.2.2

Defect ID:
ID DEFECT000269315 Technical Severity:
Severity High
Summary:
Summary Switch panic occurred when 3rd party management application performed repeat FCP LUN
emulation queries.
Symptom:
Symptom When a 3rd party device gives a bad response to a FCP LUN request, or does not respond at all,
FCPD will retry query and stuck the thread. Any new FCP LUN request that comes in from
management application will spawn a new thread to handle it. Eventually, FCPD spawns up to
the maximum number of allowed threads and the switch panics.
Feature:
Feature Field Escalation Function:
Function Fabric Services
Probability:
Probability Low
Found in Release:
Release FOS6.2.1 Service Request ID:
ID 407027
Where Else Fixed: FOS6.2.2

Fabric OS v6.3.1c Release Notes v1.0 Page 64 of 84

 Closed with Code Change in Fabric OS v6.3.0c

Defect ID:
ID DEFECT000270712 Technical Severity:
Severity High
Summary:
Summary Host failed to discover tapes due to a VI/VT database mismatch between the switches that are
part of the same Encryption Group
Symptom:
Symptom Host will not able to discovery Tape devices that are part of the same EG
Workaround:
Workaround Issue "cryptocfg --commit" again to sync up the VT/VI database across nodes in the EG.
Feature:
Feature Data Security Function:
Function Tape Encryption
Probability:
Probability Low
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000271290 Technical Severity:
Severity High
Summary:
Summary Brocade 5424 - SERDES settings do not get push correctly on v6.3.0x
Symptom:
Symptom Incorrect SERDES settings used.
Feature:
Feature Embedded Platform Services Function:
Function Superhawk2
Probability:
Probability Medium
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000273043 Technical Severity
Severity:
erity High
Summary:
Summary When running FCoE feature related scripts over multiple SMIA clients the Common Access
Library Daemon (CALD) detects a memory increase on the Brocade 8000 switch. Other FOS
based products do not exhibit the same behavior when running the same scripts.
Symptom:
Symptom 34MB memory increase seen in Common Access Library Daemon (CALD) when running 10 SMIA
clients over FCoE.
Feature:
Feature CEE-MANAGEABILITY Function:
Function CAL INTERFACE
Probability:
Probability Low
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000267497 Technical Severity:
Severity Medium
Summary:
Summary When CP restarts DPC-0, sassvrd sees ECONNRESET on DPC1 connection and BP freezes for 10
seconds
Symptom:
Symptom On one DPC failure, second DPC on the same switch also experience disruption.
Feature:
Feature FA4-18 Platform Services Function:
Function MISC
Probability:
Probability Low
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000268872 Technical Severity:
Severity Medium
Summary:
Summary The command fcoe loginshow displays unexpected values when a third party CNA is moved
between switches.
Symptom:
Symptom Unexpected values are seen in response to the loginshow command.
Feature:
Feature CEE-FCOE Function:
Function FCOE DRIVER
Probability:
Probability High
Found in Release:
Release FOS6.3.0

Fabric OS v6.3.1c Release Notes v1.0 Page 65 of 84

 Closed with Code Change in Fabric OS v6.3.0c

Defect ID:
ID DEFECT000269956 Technical Severity:
Severity Medium
Summary:
Summary OPT 322202 - IPC failure message displayed on one of the nodes when using the cryptocfg --
show -groupmember -all command
Symptom:
Symptom Customer will not be able to use "cryptocfg --show -groupmember -all" CLI to know the health of
the EG, EEs in the EG when this very remote corner case is hit. However there is no impact to
health of EG or EE states in the EG and no impact to any datapath. The health of EG can be
determined alternately by issuing "cryptocfg --show -groupcfg" and "cryptocfg --show -localEE"
CLIs on each of the Node in the EG
Workaround
Workaround:
und Issue "cryptocfg --show -groupcfg" and "cryptocfg --show -localEE" commands instead to know
the health of EG
Feature:
Feature Data Security Function:
Function Tape Encryption
Probability:
Probability Low
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000270309 Technical Severity
Severity:
ity Medium
Summary:
Summary Running FOS commands give error: shmInit: shmget failed: No space left on device
Symptom:
Symptom Unable to execute FOS commands on default switch after performing multiple cfgenable with TI
zones
Feature:
Feature FC Services Function:
Function Name Server
Probability:
Probability Low
Found in Release:
Release FOS6.3.0
Where Else Fixed: FOS6.2.2

Defect ID:
ID DEFECT000270368 Technical Severity:
Severity Medium
Summary:
Summary 1GB FCIP tunnel with 2 rate limited circuits is unable to move full I/O workload to remaining
circuit when 1 circuit fails.
Symptom:
Symptom In a multi circuit FCIP tunnel configuration circuit failover over 1G tunnels may not failover to
other available circuits.
Feature:
Feature FCIP Function:
Function FCIP Performance
Probability:
Probability Medium
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000270562 Technical Severity:
Severity Medium
Summary:
Summary FICON XRC Emulation - READTRACK_STATUS_ACCEPT flag cleared on Tunnel Down and Selective
Reset causes Abort Sequences later
Symptom:
Symptom Slow read track performance when XRC emulation is enabled, MVS IO errors are generated when
an invalid selective reset frame is sent to the controller.
Workaround:
Workaround Disable FICON XRC Emulation
Feature:
Feature FCIP Function:
Function FCIP Performance
Probability:
Probability High
Found in Release:
Release FOS6.2.0

Fabric OS v6.3.1c Release Notes v1.0 Page 66 of 84

 Closed with Code Change in Fabric OS v6.3.0c

Defect ID:
ID DEFECT000271177 Technical Severity
Severity: Medium
Summary:
Summary Additional information of the EE status in the current command that displays the overall status
of the EG, nodes and RKM(cryptocfg --show --groupcfg)
Symptom:
Symptom Customer will have to invoke "cryptocfg --show -groupcfg", "cryptocfg --show -groupmember -all"
or "cryptocfg --show -localEE" on all nodes to know the overall state of EG including EE state
across EG. There is no one place where Customer will get the EE state across EG in the same
command which provides the EG health
Feature:
Feature Data Security Function:
Function Infrastructure
Probability:
Probability Low
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000271220 Technical Severity:
Severity Medium
Summary:
Summary Unexpected termination of raslogd triggered switch panic or hafailover.
Symptom:
Symptom When auditing is on for security class, a race condition in raslogd triggered switch to panic.
Workaround:
Workaround disable auditing via: Auditcfg --disable
Feature:
Feature Field Escalation Function:
Function RAS Logging / Tracing
Probability:
Probability Low
Found in Release:
Release FOS6.1.0 Service Request ID:
ID 409971

Defect ID:
ID DEFECT000272183 Technical Severity:
Severity Medium
Summary:
Summary IFCCs encountered when processing Read Channel Extender Capabilities with XRC Emulation
Symptom:
Symptom IFCCs when IPLing systems with SDM LPARs
Workaround:
Workaround Disable FICON XRC Emulation
Feature
Feature:
re FCIP Function:
Function FCIP I/O
Probability:
Probability Low
Found in Release:
Release FOS6.2.0

Defect ID:
ID DEFECT000272203 Technical Severity:
Severity Medium
Summary:
Summary RNID frame type field from the host is corrupted internally when the host is connected over FCIP.
Symptom:
Symptom Corrupted RNID request is received from the host and rejected. As a result, the switch is unable
to get FICON CHPID online to VSM (Virtual Tape Subsystem) over an emulated or non-emulated
VE tunnel. E-Port between switches functions correctly.
Workaround:
Workaround Disable FICON Tape Emulation
Feature:
Feature FCIP Function:
Function FCIP Port
Probability:
Probability Low
Found in Release:
Release FOS6.3.0

Fabric OS v6.3.1c Release Notes v1.0 Page 67 of 84

 Closed with Code Change in Fabric OS v6.3.0c

Defect ID:
ID DEFECT000272842 Technical Severity:
Severity Medium
Summary:
Summary Switch does not broadcast Unsolicited FIP Discovery Advertisements
Symptom:
Symptom If the CNA expects UAs from the FCF even if the solicited advertisement had the “D” bit set, it will
logout of the FCF after about 20 seconds.( Tomcat does not logout, Emulex logs out)
Feature:
Feature CEE-FCOE Function:
Function FCOE Daemon
Probability:
Probability Low
Found in Release
Release:
ease FOS6.3.1

Defect ID:
ID DEFECT000274208 Technical Severity:
Severity Medium
Summary:
Summary After upgrade to FOS v6.2.x, 4G AP blade observes credit problem on virtual channel 0
Symptom:
Symptom Customer after upgrade to FOS v6.2.x, experience frame drop on SAS, FCIP, FC FastWrite and
observe host cannot see target, FCIP tunnel do not come up problems.
Workaround:
Workaround Port bounce, POR of Brocade 7600. If it is 48K with an FA4-18 blade then port bounce,
slotpower off/on of FA4-18 or POR.
Feature:
Feature Field Escalation Function:
Function ASIC Driver
Probability:
Probability High
Found in Release:
Release FOS6.2.1 Service Request ID:
ID 412817

Defect ID:
ID DEFECT000274953 Technical Severity:
Severity Medium
Summary:
Summary Rekey sessions supposed to be pending cannot be persisted when the EE hosting node fails
over
Symptom:
Symptom Customer will have to restart the rekey individually for those LUNs for which the rekey sessions
could not be automatically started if HA Cluster failover happens before keys were successfully
created for all LUNs under rekey.
Workaround:
Workaround Start the rekey sessions for LUNs on individual basis
Feature:
Feature Data Security Function:
Function Re-key
Probability:
Probability Low
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000275108 Technical Severity:
Severity Medium
Summary:
Summary Restore Master Key from recovery cards does not put EE Online when all EEs in the EG were
zeroized
Symptom:
Symptom When a customer zeroizes all EEs in the EG and restores the Master Key from recovery smart
cards will not put EE online
Workaround:
Workaround Restore MK the second time.
Feature:
Feature Data Security Function:
Function Security Processor
Probability:
Probability Low
Found in Release:
Release FOS6.3.0

Fabric OS v6.3.1c Release Notes v1.0 Page 68 of 84

Closed with Code Change in Fabric OS v6.3.0b
This section lists the defects with Critical, High and Medium Technical Severity closed with a code change as
of December 7, 2009 in Fabric OS v6.3.0b.

Defect
Defect ID:
ID DEFECT000259050 Technical Severity:
Severity Critical
Summary:
Summary FICON emulation failing.
Symptom:
Symptom MVS IOS444I error messages when trying to vary paths online to extended DASD devices.
Workaround:
Workaround Disable FICON XRC Emulation
Feature:
Feature Field Escalation Function
Function:
tion FCIP
Probability:
Probability Low
Found in Release:
Release FOS6.2.0 Service Request ID:
ID 389217
Where Else Fixed: FOS6.3.0

Defect ID:
ID DEFECT000261125 Technical Severity:
Severity High
Summary:
Summary In a large fabric with 50+ switches, firmware download (HCL) on Brocade DCX failed on the
standby CP.
Symptom:
Symptom In a large fabric with 50+ switches, non-disruptive Firmwaredownload may fail on a standby CP
of a DCX switch.
Workaround:
Workaround Run firmwaredownload again.
Feature:
Feature FIRMWARE DOWNLOAD Function:
Function Firmware Download
Probability:
Probability Low
Found in Release:
Release FOS6.3.0
Where Else Fixed: FOS6.2.2

Defect ID:
ID DEFECT000261231 Technical Severity:
Severity High
Summary:
Summary RASLOG flood occurs with internal RASLOG with following weblinkerfcg message on multiple
switches in fabric: "weblinkerfcg:1024 attempts to send message type(26) to invalid
dest(IPSIPC:1024/0), comm.c, line: 453, comp:weblinker, ltime:2009/07/28-11:39:
Symptom:
Symptom Due to excessive internal messages from one of the applications, other important RASLOG
messages may be lost from the limited log space on each switch.
Feature:
Feature FCIP Function:
Function FCIP CP
Probability:
Probability High
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000261418 Technical Severity:
Severity High
Summary:
Summary Panic Reboot on Brocade DCX after using fwshow command.
Symptom:
Symptom Switch reboot occurs after running the command "fwshow --disable --port".
Feature:
Feature Field Escalation Function:
Function Management Services
Probability:
Probability High
Found in Release:
Release FOS6.2.0 Service Request ID:
ID 394347
Where Else Fixed: FOS6.2.2, FOS6.2.1 b

Fabric OS v6.3.1c Release Notes v1.0 Page 69 of 84

 Closed with Code Change in Fabric OS v6.3.0b

Defect ID:
ID DEFECT000261593 Technical Severity:
Severity High
Summary:
Summary Switch went to faulty state after which supportsave takes very long time to complete
Symptom:
Symptom Brocade 7600 becomes faulty and supportSave takes very long time.
Feature:
Feature FA4-18 Platform Services Function:
Function ASIC Driver
Probability:
Probability High
Found in Release:
Release FOS6.2.1

Defect ID:
ID DEFECT000261797 Technical Severity:
Severity High
Summary:
Summary Brocade SMI failed to discover all switches over EX port
Symptom:
Symptom After hafailover, application fails to discover some switches over EX port due to, SMI reports
"LOGIN FAILED" after GPL2 query targeted to translate domain is rejected.
Feature:
Feature Field Escalation Function:
Function FCR
Probability:
Probability Medium
Found in Release:
Release FOS6.2.0 Service Request ID:
ID 392369
Where Else Fixed: FOS6.2.2, FOS6.2.1 a

Defect ID:
ID DEFECT000261946 Technical Severity:
Severity High
Summary:
Summary Upgrade from 6.2.0g to 6.3.0 ldap certificates are missing
Symptom:
Symptom Customer may not be able to log into switch when using LDAP authentication.
Workaround:
Workaround Log into serial console and reimport the ldap certificate(s). The degree to which the user will
be locked out would depend on how the LDAP environment was setup.
Feature:
Feature FOS Security Function:
Function LDAP
Probability:
Probability High
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000263464 Technical Severity
Severity:
rity High
Summary:
Summary Device connectivity lost when zone enabled on Brocade 7800
Symptom:
Symptom Lost device connectivity
Feature:
Feature Striker/Spike Platform Services Function:
Function Routing
Probability:
Probability High
Found in Release:
Release FOS6.3.1

Defect ID:
ID DEFECT000264398 Technical
Technical Severity:
Severity High
Summary:
Summary Common Access Layer Daemon (CALD) panics due to segmentation fault
Symptom:
Symptom A fabric that contains switches running firmware older then FOS v5.2.x could send an internal
query to directors that was not properly set up to handle switches with more than 256 ports.
This query can result in the switch with greater than 256 ports.
Feature:
Feature Field Escalation Function:
Function Management Embedded
Probability:
Probability Medium
Found in Release:
Release FOS6.2.0
Where Else Fixed: FOS6.2.2, FOS6.2.1 b

Fabric OS v6.3.1c Release Notes v1.0 Page 70 of 84

 Closed with Code Change in Fabric OS v6.3.0b

Defect ID:
ID DEFECT000265414 Technical Severity:
Severity High
Summary:
Summary Kernel panic when performing POR on DCX
Symptom:
Symptom Switch crash and reboot.
Feature:
Feature 8G ASIC Driver Function:
Function C2 ASIC driver
Probability:
Probability Low
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000265511 Technical Severity:
Severity High
Summary:
Summary Brocade 7800 DP crashed after connecting 10G ports to Anue impairment box
Symptom:
Symptom Tunnel does not come up.
Feature:
Feature FCIP Function:
Function FCP TCP/IP Stack
Probability:
Probability Low
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000265695 Technical Severity:
Severity High
Summary:
Summary Strict fabric wide policy conflict occurs after HA failover
Symptom:
Symptom Switch segmented out of fabric.
Feature:
Feature FC Services Function:
Function ESS
Probability:
Probability Low
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000265697 Technical Severity:
Severity High
Summary:
Summary Block port is not being displayed in IPL file after host blocks port in-band
Symptom:
Symptom IPL file is not updated.
Feature:
Feature FICON Function:
Function Ficud
Probability:
Probability Low
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000265834 Technical Severity:
Severity High
Summary:
Summary RLIR in IM2 fabric is using domain with offset stripped
Symptom:
Symptom RLIR or DRLIR generated by FOS did not contain domain offset of 0x60 in PID & TAG fields when
running IM2 mode.
Feature:
Feature FICON Function:
Function MS-FICON
Probability:
Probability High
Found in Release:
Release FOS6.3.0

Fabric OS v6.3.1c Release Notes v1.0 Page 71 of 84

 Closed with Code Change in Fabric OS v6.3.0b

Defect ID:
ID DEFECT000267476 Technical Severity:
Severity High
Summary:
Summary 7800 panic during overnight workload
Symptom:
Symptom 7800 switch crashed and FCIP I/O stopped.
Feature:
Feature Striker/Spike Platform Services Function:
Function Blade Driver
Probability:
Probability Low
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000267481 Technical Severity:
Severity High
Summary:
Summary Internal FICON error when doing port swap.
Symptom:
Symptom Internal FICON error
Feature:
Feature FICON Function:
Function Other
Probability:
Probability Low
Found
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000269111 Technical Severity:
Severity High
Summary:
Summary No NPIV devices (including AG) can log into ports of the 7800 when port is changed from EX port
to NPIV after non-disruptive upgrade
Symptom:
Symptom NPIV ports cannot login.
Feature:
Feature Striker/Spike Platform Services Function:
Function Spike Platform Module
Probability:
Probability Low
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000269604 Technical Severity:
Severity High
Summary:
Summary FICON Emulation not handling Abort Sequence correctly and causing DSO FICON CRC Errors
Symptom:
Symptom IO Errors during XRC RRS processing and eventual suspend of the session that encounters the
error.
Workaround:
Workaround Disable FICON XRC Emulation
Feature:
Feature FCIP Function:
Function FCIP I/O
Probability:
Probability Low
Found in Release:
Release FOS6.2.0

Defect
Defect ID:
ID DEFECT000246346 Technical Severity:
Severity Medium
Summary:
Summary During stress testing, after multiple VLAN configuration changes, logins from the CNA are
unsuccessful.
Symptom:
Symptom Multiple VLAN configuration changes result in FLOGI being ignored.
Feature:
Feature CEE-FCOE Function:
Function FCOE Daemon
Probability:
Probability Medium
Found in Release:
Release FOS6.1.3_cee

Fabric OS v6.3.1c Release Notes v1.0 Page 72 of 84

 Closed with Code Change in Fabric OS v6.3.0b

Defect ID:
ID DEFECT000246883 Technical Severity:
Severity Medium
Summary:
Summary Pre-FIP LOGO with Invalid WWNN (non-existent fabric device) is accepted
Symptom:
Symptom Incorrect device logout.
Feature:
Feature CEE-FCOE Function:
Function FCOE DRIVER
Probability:
Probability High
Found in Release:
Release FOS6.1.3_cee

Defect ID:
ID DEFECT000247639 Technical Severity:
Severity Medium
Summary:
Summary Switch responds to FIP FLOGI when SP bit is on and FP bit is off
Symptom:
Symptom Incorrect FIP FLOGI response sent by switch.
Feature:
Feature CEE-FCOE Function:
Function FCOE DRIVER
Probability:
Probability Low
Found in Release:
Release FOS6.1.3_cee

Defect ID:
ID DEFECT000248213 Technical Severity:
Severity Medium
Summary:
Summary FIP FLOGI accepted when host supports only spma
Symptom:
Symptom Incorrect FIP FLOGI request is accepted rather than rejected.
Feature:
Feature CEE-FCOE Function:
Function FCOE DRIVER
Probability:
Probability Low
Found in Release:
Release FOS6.1.3_cee

Defect ID:
ID DEFECT000255703 Technical Severity:
Severity Medium
Summary:
Summary Brocade 8000 floods FCP traffic on two ports to CNAs
Symptom:
Symptom Brocade 8000 sends FCP traffic to the wrong CNA.
Feature:
Feature CEE-FCOE Function:
Function FCOE DRIVER
Probability:
Probability High
Found in Release:
Release FOS6.1.2_cee Service Request ID:
ID 384593

Defect ID:
ID DEFECT000257211 Technical Severity:
Severity Medium
Summary:
Summary Weblinker.fcg terminates several times during third party host scan.
Symptom:
Symptom When third party host scan was run, http daemon died and restart several times may trigger
temporary management service interruption.
Feature:
Feature Field Escalation Function:
Function Web Management
Probability:
Probability Medium
Found in Release:
Release FOS6.2.0 Service Request ID:
ID 386535
Where Else Fixed: FOS6.2.2

Fabric OS v6.3.1c Release Notes v1.0 Page 73 of 84

 Closed with Code Change in Fabric OS v6.3.0b

Defect ID:
ID DEFECT000258696 Technical Severity:
Severity Medium
Summary:
Summary Switch responds with advertisement to solicitation with SP bit on
Symptom:
Symptom Customer will see a response to a solicitation with SP bit on.
Feature:
Feature CEE-FCOE Function:
Function FCOE DRIVER
Probability:
Probability Low
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000259855 Technical Severity:
Severity Medium
Summary:
Summary When FCoE max login has been reached, need to change debug log to customer visible RASLOG,
to indicate FCoE login has been reached.
Symptom:
Symptom Customer may not know the reason for login reject in case FCoE login limit has been reached.
Feature:
Feature CEE-FCOE Function:
Function FCOE DRIVER
Probability:
Probability Medium
Found
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000261132 Technical Severity:
Severity Medium
Summary:
Summary In a large fabric with more than 56 switches, edge Brocade DCX panics due to termination of
msd during fabric reconfiguration.
Symptom:
Symptom While doing switchdisable; agshow; switchenable loop on a large fabric with AG device, switch
panics.
Feature:
Feature Fabric Infrastructure Function:
Function MANAGEMENT SERVER
Probability:
Probability Low
Found in Release:
Release FOS6.3.0
Where Else Fixed: FOS6.2.2, FOS6.2.1 a

Defect ID:
ID DEFECT000261754 Technical
Technical Severity:
Severity Medium
Summary:
Summary Observing ffdc data files during continuous interface flap
Symptom:
Symptom Interface flapping/ bad cable shows to many ras log messages
Workaround:
Workaround Shut down the port and replace the faulty cable and enable the port
Feature:
Feature CEE-Infrastructure Function:
Function ANVIL DRIVER
Probability:
Probability High
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000263948 Technical Severity:
Severity Medium
Summary:
Summary FIP: when CNA send FIP ver=0, switch should not validate MAC descriptor field for backwards
compatibility
Symptom:
Symptom Switch rejects login due to backward incompatibility.
Feature:
Feature CEE-FCOE Function:
Function FCOE DRIVER
Probability:
Probability Medium
Found in Release:
Release FOS6.3.1

Fabric OS v6.3.1c Release Notes v1.0 Page 74 of 84

 Closed with Code Change in Fabric OS v6.3.0b

Defect ID:
ID DEFECT000264578 Technical Severity:
Severity Medium
Summary:
Summary Supportsave did not remove ffdc files. Continued to get ffdc files warning
Symptom:
Symptom Supportsave command did not clear FFDC files. FFDC file warning message persisted until a
second support save was taken.
Feature:
Feature RAS Function:
Function FFDC/Supportsave
Probability:
Probability Low
Found in Release:
Release FOS6.3.0 Service Request ID:
ID 399193
Where Else Fixed: FOS6.2.2

Defect ID:
ID DEFECT000265225 Technical Severity:
Severity Medium
Summary:
Summary Unsupported SFP amber flashing state is cleared by plugging an optical cable into the SFP.
Actual port status is not affected.
Symptom:
Symptom An unsupported SFP installed in an FX8-24 can have the amber LED extinguished if a cable is
plugged into the SFP. The actual port status is not changed but the visible indication of a fault
(flashing amber) is extinguished.
Feature:
Feature Striker/Spike Platform Services Function:
Function Spike Platform Module
Probability:
Probability Medium
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000265396 Technical Severity:
Severity Medium
Summary:
Summary Web Tools shows iodset off but CLI shows it is enabled.
Symptom:
Symptom Incorrect IOD configuration state is displayed through Web Tools.
Workaround:
Workaround Using CLI to view the configured IOD state when IOD is enabled with Lossless DLS
Feature:
Feature WebMgmt Function:
Function WT Platform Support
Probability:
Probability Low
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000265398 Technical Severity:
Severity Medium
Summary:
Summary Brocade Encryption Switch went faulty during rekey operation
Symptom:
Symptom Brocade Encryption Switch faulted, rekey failed and required a power cycle.
Feature:
Feature Data Security Function:
Function Re-key
Probability:
Probability Low
Found in Release:
Release FOS6.2.1 Service Request ID:
ID 401091

Defect ID:
ID DEFECT000265399 Technical Severity:
Severity Medium
Summary:
Summary BES did not rejoin Encryption Group after reboot
Symptom:
Symptom Encryption switch cannot rejoin Encryption Group resulting in split.
Feature
Feature:
re Data Security Function:
Function Infrastructure
Probability:
Probability Low
Found in Release:
Release FOS6.2.1 Service Request ID:
ID 401091

Fabric OS v6.3.1c Release Notes v1.0 Page 75 of 84

 Closed with Code Change in Fabric OS v6.3.0b

Defect ID:
ID DEFECT000265530 Technical Severity:
Severity Medium
Summary:
Summary I/O traffic get flooded in to port 16
Symptom:
Symptom Incorrect port showing I/O traffic.
Feature:
Feature CEE-Infrastructure Function:
Function ANVIL DRIVER
Probability:
Probability Medium
Found in Release:
Release FOS6.3.1

Defect ID:
ID DEFECT000265563 Technical Severity:
Severity Medium
Summary:
Summary Web Tools launch fails with license error/doget failed from DCFM
Symptom:
Symptom While launching the Web tools, in some corner cases HTTP request for authentication may result
in failure. A subsequent Web tools session clears this issue.
Feature:
Feature WebMgmt Function:
Function Webstart
Probability:
Probability Medium
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000265753 Technical Severity:
Severity Medium
Summary:
Summary Improve BES error handling when the backend tape target is not responsive
Symptom:
Symptom Host cannot recover if backend tape target become not responsive during BES initiated
commands.
Feature:
Feature Data Security Function:
Function Tape Encryption
Probability:
Probability Medium
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000267358 Technical Severity:
Severity Medium
Summary:
Summary sfpshow: smart data is not refreshed by polling loop for GE type ports
Symptom:
Symptom Newer smart data (for GE type ports) such as SFP temperature and power are not updated by
the automatic polling loop that occurs roughly every 5 minutes.
Feature:
Feature Striker/Spike Platform Services Function:
Function Spike Platform Module
Probability:
Probability High
Found in Release:
Release FOS6.3.0

Defect
Defect ID:
ID DEFECT000267415 Technical Severity:
Severity Medium
Summary:
Summary Supportsave does not capture all the FID with index greater than 3
Symptom:
Symptom Information for FID with index greater than 3 is not captured in supportSave.
Feature:
Feature VF Infrastructure Function:
Function LS Config CLI
Probability:
Probability Medium
Found in Release:
Release FOS6.3.0

Fabric OS v6.3.1c Release Notes v1.0 Page 76 of 84

 Closed with Code Change in Fabric OS v6.3.0b

Defect ID:
ID DEFECT000268955 Technical Severity:
Severity Medium
Summary:
Summary links on the AG (port 19) went into a disabled state with the reason: "NPIV not supported by
Fabric port". However, the edge switch port (7/27) had NPIV enabled.
Symptom:
Symptom port on AG switch become disabled.
Feature:
Feature Access Gateway Services Function:
Function Daemon
Probability:
Probability Low
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000269138 Technical Severity:
Severity Medium
Summary:
Summary In the Element Manager, under switch admin, we selected FCoE Login and got an error message
of "FCoE Login Management is disabled in the switch; make sure you enable it to view the
chassis".
Symptom:
Symptom "FCoE Login" tab name causes confusion. It needs to be changed to "FCoE Login Group".
Feature:
Feature WebMgmt Function:
Function WT Platform Support
Probability:
Probability High
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000269286 Technical Severity:
Severity Medium
Summary:
Summary portdisable xge0 did not actually disable the port although RAS log and switchshow show it is
disabled, the FCIP tunnels are still up and running.
Symptom:
Symptom xge0 port on FX8-24 is not properly disabled when running portdisable CLI.
Feature:
Feature Striker/Spike Platform Services Function:
Function BFOS
Probability:
Probability Medium
Found in Release
Release:
se FOS6.3.1

Fabric OS v6.3.1c Release Notes v1.0 Page 77 of 84

Closed with Code Change in Fabric OS v6.3.0a
This section lists the defects with Critical, High and Medium Technical Severity closed with a code change as
of September 28, 2009 in Fabric OS v6.3.0a.

Defect ID:
ID DEFECT000263579 Technical Severity
Severity:
verity Critical
Summary:
Summary Switch panic occurred when management application performed repeat FCP LUN emulation
queries through SMI interface or application polling a switch that had password changed
multiple times.
Symptom:
Symptom Switch panic is experienced. Switch console logs Out of Memory kill.
Workaround:
Workaround Disable SMI agents.
Feature:
Feature Field Escalation Function:
Function Panic / OOM
Probability:
Probability High
Found in Release:
Release FOS6.2.1 Service Request ID:
ID 399773

Defect ID:
ID DEFECT000247761 Technical Severity:
Severity High
Summary
Summary:
ary Sysshutdown on Brocade 5480 may cause panic and reboots
Symptom:
Symptom Switch panic during sysshutdown
Workaround:
Workaround Use CLI "shutdown" command.
Feature:
Feature Embedded Platform Services Function:
Function Bulova
Probability:
Probability High
Found in Release:
Release FOS6.2.0 Service Request
Request ID:
ID 375389

Defect ID:
ID DEFECT000254576 Technical Severity:
Severity High
Summary:
Summary Brocade FR4-18i heartbeat dead causes reboot.
Symptom:
Symptom Processor on FR4-18i blade reboots while traffic is running over FCIP links. May cause CP
failover to take place, only traffic on the FR4-18i blade is disrupted.
Feature:
Feature Field Escalation Function:
Function FCIP Flipper/ASIC
Probability:
Probability Low
Found in Release:
Release FOS6.2.0 Service Request ID:
ID 374539

Defect ID:
ID DEFECT000259327 Technical Severity:
Severity High
Summary:
Summary After changing domain offset followed by 'hafailover'-"Unknown LSR type" messages started
scrolling continuously on console log for Brocade DCX-4S, DCX and 48000 switches running in
Interopmode2.
Symptom:
Symptom After changing the domain offset, followed by 'hafailover' on CP1, CP0 immediately started
posting "Unknown LSR type" messages continuously on console log.
Workaround:
Workaround Run hafailover to failover to other CP.
Feature:
Feature FC Services Function:
Function FSPF
Probability:
Probability Low
Found in Release:
Release FOS6.3.0

Fabric OS v6.3.1b Release Notes v1.0 Page 78 of 84

 Closed with Code Change in Fabric OS v6.3.0a

Defect ID:
ID DEFECT000262164 Technical Severity:
Severity High
Summary:
Summary Under heavy traffic on 10G tunnel, continuous tunnel modification can cause traffic to halt
Symptom:
Symptom FCIP I/O traffic disruption during tunnel modification.
Workaround:
Workaround Slot power off/on the Brocade FX8-24 blade.
Feature
Feature:
ture FCIP Function:
Function Compression
Probability:
Probability Medium
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000262167 Technical Severity:
Severity High
Summary:
Summary I/O fails to across VE link when failover is done on a trunked EX port
Symptom:
Symptom Medusa I/O on a host connected to storage across a VE link times out and stops when
replication software I/O is running across the same link.
Feature:
Feature Striker/Spike Platform Services Function:
Function VEX
Probability:
Probability High
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000262247 Technical
Technical Severity:
Severity High
Summary:
Summary Zoning fails with "Transaction Commit failed. Loss of an E-port to a neighboring Mi10k in the
middle of a zone push operation caused the zoning request to fail. Zoning fails with
"Transaction Commit failed. Reason code 2 (26) - "Aca Was Rejected: Remote Switch Busy,
Retry in a few seconds"
Symptom: Zoning fails with "Transaction Commit failed. Reason code 2 (26) - "Aca Was Rejected: Remote
Switch Busy, Retry in a few seconds"
Workaround:
Workaround FC Services
Feature:
Feature Zoning Function
Function: Low
Probability:
Probability 396077 Risk of Fix:
Fix (Not Checked)
Found in Release:
Release v6.2.0d Service Request ID:
ID FOS6.2.0
Publications

Defect ID:
ID DEFECT000262261 Technical Severity:
Severity High
Summary:
Summary Traffic cannot run across edge to edge topology when compression and FastWrite are enabled.
Symptom:
Symptom I/O traffic is unable to run.
Feature:
Feature FCIP Function:
Function FCIP I/O
Probability:
Probability High
Found in Release:
Release FOS6.3.0

Fabric OS v6.3.1c Release Notes v1.0 Page 79 of 84

 Closed with Code Change in Fabric OS v6.3.0a

Defect ID:
ID DEFECT000262333 Technical Severity:
Severity High
Summary:
Summary SFP power supply values are not displayed correctly after doing a non-disruptive firmware
upgrade to FOS v6.2.1 or FOS v6.3.0
Symptom:
Symptom SFP voltage may show incorrect values
Workaround:
Workaround Execute the same command again to get the correct values.
Feature:
Feature 8G Platform Services Function:
Function FOS Kernel Drivers
Probability:
Probability Medium
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000262419 Technical Severity:
Severity High
Summary:
Summary Under impairment, network configuration with high compressible data may result in tunnel
bounce
Symptom:
Symptom FCIP tunnel may go up and down in an impairment network configuration with highly
compressible data I/O.
Workaround:
Workaround Tunnel will recover after going down.
Feature:
Feature FCIP Function:
Function FCP TCP/IP Stack
Probability:
Probability Medium
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000262516 Technical
Technical Severity:
Severity High
Summary:
Summary Tunnel did not come up due to configuration mismatch for tape pipelining, one side shows
"Write only" and other side shows "Write/Read"
Symptom:
Symptom VE tunnel configuration not coming up.
Feature:
Feature FCIP Function:
Function FCIP CLI
Probability
Probability:
ility Medium
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000262891 Technical Severity:
Severity High
Summary:
Summary Ports go offline with link reset
Symptom:
Symptom High CPU load from external SAN management application such as doing supportsave from
Brocade DCFM is causing laser flt / link reset on port.
Feature:
Feature 4G ASIC Driver Function:
Function PORT
Probability:
Probability High
Found in Release:
Release FOS6.2.1 Service Request ID:
ID 397469

Fabric OS v6.3.1c Release Notes v1.0 Page 80 of 84

 Closed with Code Change in Fabric OS v6.3.0a

Defect ID:
ID DEFECT000263397 Technical Severity:
Severity High
Summary:
Summary Brocade DCX running FOS v6.2.1 & M6140 running M-EOS v9.9.0 - Nameserver database
counts do not match for FOS and M-EOS switches in same fabric
Symptom:
Symptom Host cannot see device due to name server has no entries about the device. This happens
when there is a HBA capable of RHBA command and EOS (McDATA) switch in the same fabric.
Feature:
Feature FC Services Function:
Function FDMI
Probability:
Probability Medium
Found in Release:
Release FOS6.2.1 Service Request ID:
ID 398757

Defect ID:
ID DEFECT000264566 Technical Severity:
Severity High
Summary:
Summary Switch panic triggered by size-64 kernel message buffer being used up in virtual fabric with
logical ISL configured
Symptom:
Symptom Switch panic will be observed. Configuration requires VF with LISL configured. Prior to panic,
cat /proc/slabinfo as root will show a large number on size-64 block: slabinfo: size-64
7583624 7583624
Workaround:
Workaround Configure only DISLs between switches.
Feature:
Feature Logical Fabric Function:
Function Kernel Driver
Probability:
Probability High
Found in Release:
Release FOS6.2.1

Defect ID:
ID DEFECT000264640 Technical Severity:
Severity High
Summary:
Summary Configdownload does download some of the FCoE setting in FOS v6.3.0 that prevents factory
install
Symptom:
Symptom Prohibit factory install; missing entries are: fcoe.et.cfg:0x0, fcoe.fcmap:0x0
fcoe.fip.advintvl:0x0, fcoe.lg:0x0, fcoe.rcs.gen_number:0x0
Feature:
Feature CEE-FCOE Function:
Function FCOE PROTOCOL
Probability:
Probability High
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000264650 Technical Severity:
Severity High
Summary:
Summary History Buffer is updated according to Port Address rather than Port Number
Symptom:
Symptom Port reference provided to FICON host by the Director History Buffer for port parameter changes
is incorrect. In reading the switch configuration to gather updates for port parameter changes,
FICON host may reference a different port than the one that has changed state.
Feature:
Feature FICON Function:
unction Ficud
Probability:
Probability High
Found in Release:
Release FOS6.3.1

Fabric OS v6.3.1c Release Notes v1.0 Page 81 of 84

 Closed with Code Change in Fabric OS v6.3.0a

Defect ID:
ID DEFECT000247754 Technical Severity:
Severity Medium
Summary:
Summary Brocade switch gets nsd panic in interopmode 3 when running FOS v6.2.
Symptom:
Symptom Customer may notice NSd panic
Feature:
Feature Field Escalation Function:
Function Fabric Services
Probability:
Probability High
Found in Release:
Release FOS6.2.0

Defect ID:
ID DEFECT000253083 Technical Severity:
Severity Medium
Summary:
Summary Transient detected error on internal link causes blade to be faulted
Symptom:
Symptom Port blade will be faulted with "reason=5"
Workaround:
Workaround Slotpoweroff and slotpoweron clears the fault
Feature:
Feature 8G ASIC Driver Function:
Function C2 ASIC driver
Probability:
Probability Medium
Found in Release:
Release FOS6.2.0 Service Request ID:
ID 378361

Defect ID:
ID DEFECT000260664 Technical Severity:
Severity Medium
Summary:
Summary After downgrading from FOS v6.3.0 to 6.2.0x, the bit count in fwconfigure – Eport –
StateChange is 63.
Symptom:
Symptom Once the user has a specific Eport StateChange configuration, if the command “fwconfigure –
eport – ST” is run after downgrading FOS v6.3.0 to 6.2.0x, the threshold is set at 63. This value
is not allowable in FOS v6.2.x since port fencing does not support State change in FOS v6.2.x.
Feature:
Feature Fabric Infrastructure Function:
Function Fabric Watch
Probability:
Probability Low
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000261654 Technical Severity:
Severity Medium
Summary:
Summary During non-disruptive upgrade of FOS v6.3.0 on a Brocade5300 switch, "Software 'verify' error
seen on console
Symptom:
Symptom Software verify error when upgrading between two firmware versions.
Feature:
Feature Fabric Infrastructure Function:
Function Fabric Watch
Probability:
Probability Low
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000261978 Technical Severity:
Severity Medium
Summary:
Summary Retransmit and Out of order counters in portshow fciptunnel output do not show correct values.
Symptom:
Symptom Portshow fciptunnel dose not show correct counter value.
Feature:
Feature FCIP Function:
Function FCIP CLI
Probability:
Probability High
Found in Release:
Release FOS6.3.0

Fabric OS v6.3.1c Release Notes v1.0 Page 82 of 84

 Closed with Code Change in Fabric OS v6.3.0a

Defect ID:
ID DEFECT000261982 Technical Severity:
Severity Medium
Summary:
Summary For some reason, if the first tunnel, the first circuit is not numbered 0, portshow fciptunnel all -c
will add the line with "16 0 unknwn Disable ----- 0s 0.00 0.00 0 0/0 0"
Symptom:
Symptom Incorrect tunnel/circuit number shown.
Feature:
Feature FCIP Function:
Function FCIP CLI
Probability:
Probability Medium
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000262329 Technical Severity:
Severity Medium
Summary:
Summary Configdefault does not delete the FCIP configurations even after chassis reboot.
Symptom:
Symptom FCIP configuration cannot be restored to the default setting via configdefault.
Feature:
Feature FCIP Function:
Function FCIP CP
Probability:
Probability Medium
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000263562 Technical Severity:
Severity Medium
Summary:
Summary Brocade switch drops frames received from host when the switch is unable to determine a valid
state for the back end tape
Symptom:
Symptom Frames from host to tape device are dropped by the switch.
Feature:
Feature Field Escalation Function:
Function Encryption
Probability:
Probability Medium
Found in Release:
Release FOS6.2.0

Defect ID:
ID DEFECT000263775 Technical Severity:
Severity Medium
Summary
Summary:
ary Switch View:In Striker face plate image, 10GE ports should be renamed as XGE ports.
Symptom:
Symptom Different naming for the same port may mislead the user.
Feature:
Feature WebMgmt Function:
Function Switch Explorer/Switch View
Probability:
Probability High
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000263805 Technical Severity:
Severity Medium
Summary:
Summary Ifname for xGIGE ports should show as in CLI.
Symptom:
Symptom The ifName value returned for xGIGE port does not match with the CLI output.
Feature:
Feature Mgmt Embedded - SNMP Function:
Function Other
Probability
Probability:
ability Medium
Found in Release:
Release FOS6.3.1

Fabric OS v6.3.1c Release Notes v1.0 Page 83 of 84

 Closed with Code Change in Fabric OS v6.3.0a

Defect ID:
ID DEFECT000264469 Technical Severity:
Severity Medium
Summary:
Summary Support of large ITL nexus in tape to handle multiplex/multistream environment
Symptom:
Symptom If the IT (target containers with initiator) is greater than 200, decreased performance is seen for
some containers.
Workaround:
Workaround Reduce the number of IT configuration (target containers with initiators) to 200.
Feature:
Feature OS Services Function:
Function Linux Kernal
Probability:
Probability Medium
Found in Release:
Release FOS6.3.0 Service
Service Request ID:
ID 394589

Defect ID:
ID DEFECT000264871 Technical Severity:
Severity Medium
Summary:
Summary NS does not send subsequent PLOGI ACC following a sequence where NPIV device sends LOGO
before link down.
Symptom:
Symptom NPIV tape devices may not be seen by any of the hosts
Feature:
Feature FC Services Function:
Function Name Server
Probability:
Probability Medium
Found in Release:
Release FOS6.3.0 Service Request ID:
ID 397897

Defect ID:
ID DEFECT000264971 Technical Severity:
Severity Medium
Summary:
Summary Unlike FC ports, GE ports will stick at No_Sync when you swap Invalid/Non-Brocade branded
SFP to Valid Brocade SFP.
Symptom:
Symptom GE ports will not come on line if unsupported SFP have been plugged in previously.
Workaround:
Workaround Portdisable and portenable after inserting supported SFP.
Feature:
Feature Striker/Spike Platform Services Function:
Function BFOS
Probability:
Probability Medium
Found in Release:
Release FOS6.3.0

Defect ID:
ID DEFECT000265149 Technical Severity:
Severity Medium
Summary:
Summary SFP hot-plug: Copper SFP can get into illegal state: Port State=Online and Port Phys=No_Light
and link led=OFF
Symptom:
Symptom Copper SFP on 7800 shows no LED light, while port is online and working.
Feature:
Feature Striker/Spike Platform Services Function:
Function Spike Platform Module
Probability:
Probability Low
Found in Release:
Release FOS6.3.0

Fabric OS v6.3.1c Release Notes v1.0 Page 84 of 84