1.

1 Motion
Speed

N4 Speed

Speed is the distance travelled by an object per second (usually expressed in metres per
second, m/s or ms-1).
Average Speed
The average speed of an object is the average for the whole journey
(total distance travelled divided by time taken).
e.g. Sports presenters on T.V. measure the average speed of a footballer’s shot at goal

Instantaneous Speed
The instantaneous speed of an object is its speed at one particular point during the journey.
e.g. speed cameras measure the speed of a vehicle at a particular point in a journey to ensure
that it is within the speed limit.

Speed during a journey

During a journey the instantaneous speed of a vehicle will change. For example at one point
a car may be travelling along a street at 30 mph and when it is stopped at traffic lights its
speed is 0 mph. These speeds can be very different from the average speed which may be
something like 8 mph.

N4 Speed, Distance and Time Equation

From the definition: speed = distance Quantity Symbol SI Unit

time m/s or
speed v
In symbol form: v = d d=vt t= d ms-1
t v distance d m
time t s
Example: Calculate the average speed of a car which takes 3 minutes to travel 1000m.
List Equation d=vt (as written in data book)
d= 1000 m Substitute 1000 = v x 180
v=? Answer & units v = 5.56 ms-1
t = 3 minutes = 180 s
N4 Measuring Average Speed (v)

 Measure distance (d) travelled with a measuring tape.

 Measure time (t) taken for the vehicle to travel the distance (d) with a timer.
 Use the equation v = d to calculate the average speed (v).
t

vehicle timer
d

N4 Measuring Instantaneous Speed (v)

 Measure the length of the vehicle (or card attached to the vehicle) (d) with a measuring
tape.
 Measure time (t) taken for the vehicle to pass a point with a light gate connected to a
timer.
 Use the equation v = d to calculate the instantaneous speed (v).
t
timer
light
gate

light
d gate

Example: Calculate the speed of a car as it passes through the traffic lights. The car is 4m long
and takes 0.75s to pass the traffic lights.
List Equation d=vt
d= 4m Substitute 4 = v x 0.75
v=? Answer & units v = 5.33ms-1
t = 0.75s
 Vectors and Scalars

N5 Classifying Vectors and Scalars

Physical quantities can be divided into two groups:

 a scalar quantity is completely described by stating its magnitude (size) only.
 a vector quantity is completely described by stating its magnitude and direction.

Which quantities are scalars and which are vectors?

Scalars Vectors
distance displacement
speed velocity
mass force
time acceleration
energy

N5 Vector Diagrams

In order to carry out any calculations we need to know how to calculate the resultant of two
vector quantities. This is illustrated in the examples below.

In a straight line N
The resultant vector
= 4 – 3 = 1 m (090) or 1 m (due East)
3m 4m

At right angles
Hints 4m N 4m
 Ensure all vectors are
Ѳ
drawn tip to tail
3m 3m
 Draw a North line at
the start point Use Pythagoras to calculate the magnitude of
the vector
 Draw the resultant
x2 = 32 + 42
vector from the start to
x = 5m
the end point
Use Tan Ѳ = opp / adj to find angle Ѳ
 All bearings are
measured clockwise Tan Ѳ = 4 / 3
from the North line to Ѳ = 53.1o bearing = 90 – 53.1 = 36.9
the resultant vector. Resultant vector = 5 m (036.9)
N5 Vector Diagrams and Calculations (ctd)

Distance and Displacement

Distance is the total distance travelled regardless of the direction.
Displacement is the length measured from the start point to the end point in a straight line. Its
direction must be stated.

Speed and Velocity

As stated previously, speed is defined as the distance travelled per second.
Velocity can be defined as the displacement (s) of an object per second (t) measured in ms -1.

Speed and velocity are described by the equations below:

speed = distance velocity = displacement

time time Quantity Symbol SI Unit
m/s or
In symbol form the velocity equation is: velocity v
ms-1
v= s s=vt t= s
displacement s m
t v
time t s
Velocity is a vector quantity and speed is scalar.
The direction of the velocity will be the same as the direction of the displacement.

Example: A woman walks 3 m due North and then 4 m due East. She takes 10 seconds.
a) Find the (i) distance she has walked and (ii) her displacement.
b) Calculate her (i) average speed and (ii) velocity.

Solution
We will represent her walk by drawing a vector diagram. 4m

3m
s
N Ѳ
a) (i) The distance she has travelled is 3 + 4 = 7 m
(ii) Her displacement can be calculated using Pythagoras:
s2 = 32 + 42
s=5m
The angle Ѳ is calculated using
Tan Ѳ = 4 / 3
Ѳ = 53o
s = 5 m (053)

b) (i) d = 7 m d= v t
v=? 7 = v x 10
t = 10 s v = 0.7 ms-1

(ii) s = 5 m s = vt
v=? 5 = v x 10
t = 10 s v = 0.5 ms-1 (053) Remember that velocity is a vector and requires a
bearing = bearing of the displacement.
 Acceleration
N4 N5 Acceleration

Acceleration is the change in speed (or velocity) every second and is measured in metres per
second per second (ms-2).

It can be calculated using the formula:

Quantity Symbol SI Unit

acceleration = final velocity – initial velocity
m/s/s or
time acceleration a
ms-2
In symbol form: a=v–u final velocity v ms-1
t Initial velocity u ms-1
time t s
A common form of the equation worth remembering
is v = u + at

Example:
1. Calculate the acceleration of a vehicle travelling from rest to 12 ms-1 in 5 s.
a=? a=v-u
-1
v = 12 ms t
u = 0 (at rest) a = 12 - 0
t=5s 5
a = 2.4 ms-2

2. A car accelerates at 4 ms-2 for 10 s from rest. Calculate the sped of the car after 10 s. N5
a = 4 ms-2 a=v-u
v=? t
u = 0 (at rest) v = u + at
t = 10 s v = 0 + (4 x 10)
v = 40 ms-1

3. Calculate the deceleration of a train which travels from 30 ms-1 to 16 ms-1 in a time of 1
minute. N5
a=? a=v-u
-1
v = 16 ms t
-1
u = 30 ms a = 16 - 30
t = 1 minute = 60 s 60
a = - 0.47 ms-2 deceleration = 0.47 ms-2
 Graphs
N4 Speed – Time Graphs
A speed-time graph is a useful way of describing the motion of an object.
Since speed is a scalar quantity, a speed-time graph considers motion in one direction only.

The graphs below illustrate the 3 types of motion you will study.

v/ms-1 v/ms-1 v/ms-1

o t/s o t/s o t/s

constant speed increasing speed decreasing speed
(constant acceleration) (constant deceleration)
The steeper the line (larger gradient) the greater the acceleration

Example: The motion of a car over 50 s is described in the speed-time graph below.

v/ms-1

1 2 3

0 10 40 50 t/s

a) Calculate the acceleration of the car during the first 10 s.

b) Calculate the distance travelled by the car for the entire 50 s.

Solution
a) a = ? a=v-u
v = 8 ms-1 t
u = 0 (at rest) a= 8-0
t = 10 s 10
a = 0.8 ms-2

b) To calculate the distance travelled we cannot use d = vt as the speed is not

constant throughout the journey.
The distance travelled = area under the speed-time graph
Area 1 = ½ (10 x 8) = 40 (area of right angled triangle)
Area 2 = 30 x 8 = 240 (area of rectangle)
Area 3 = ½ (10 x 8) = 40 (area of right angled triangle)

Total area = 40 + 240 + 40 = 320 so distance travelled = 320m

N5 Velocity – Time Graphs
A velocity-time graph is a useful way of describing the motion of an object.
Since velocity is a vector quantity, a velocity-time graph can consider motion in two directions.

The graphs below illustrate the 3 types of motion you will study.

v/ms-1 v/ms-1 v/ms-1

o t/s o t/s o t/s

constant velocity increasing velocity decreasing velocity
(constant acceleration) (constant deceleration)
The steeper the line (larger gradient) the greater the acceleration

Example: The motion of a car over 40 s is described in the velocity-time graph below.

3
v/ms-1
10
8

1 2 4 5
0 t/s
5 10 30 40
a) During which stage of the journey is the acceleration of the car the greatest?
b) Calculate the deceleration of the car between 30 and 40 s.
c) Calculate the displacement of the car for the entire 40 s.

Solution
a) Between 0 and 5 s. (the gradient of the line is greater than 5 s to 10 s)
b) a = ? a=v-u
v=0 t
-1
u = 10ms a = 0- 10
t = 10s 5
a = -2 ms-2 deceleration = 2ms-2

c) Displacement = area under the velocity-time graph

Area 1 = ½ (5 x 8) = 20 Area 4 = 20 x 10 = 200
Area 2 = 5 x 8 = 40 Area 5 = ½ (10 x 10) = 50
Area 3 = ½ (5 x 2) = 5

Total area = 20 + 40 + 5 + 200 + 50 = 315 so the displacement = 315 m

 1.2 Forces
N4 Effects of Forces

Forces can only be detected by their effects.

They can change:
• the shape of an object e.g. squeezing plasticine
• the speed of an object e.g. kicking a football from rest
• the direction of movement of an object e.g. hitting a tennis ball with a racquet.
����� ���� ���� ���� ���� ���� ���
����� ���� ���� ���� ���� ���� ���
����� ���� ���� ���� ���� ���� ���
����� ���� ���� ���� ���� ���� ���
����� ���� ���� ���� ���� ���� ���
����� ���� ���� ���� ���� ���� ���
����� ���� ���� ���� ���� ���� ���

N4 N5 Measurement of Forces

Forces are measured in units called newtons (N). Force is a Vector quantity.
Forces can be measured with a newton balance. This instrument depends on the effect of a
force on the shape (length) of a spring.
 The force to be measured is
����� ���� ���� ���� ���� ���� ���
����� ���� ���� ���� ���� ���� ���
����� ���� ���� ���� ���� ���� ���

applied to the hook which is

attached to the spring.
marker  The force causes the spring to
stretch.
 The greater the force, the
scale greater the stretch of the spring
spring
and the further the marker
moves across the scale.

hook
Force to be measured
is applied here
 Friction

N4 Introduction to Friction

Friction is a resistive force, which opposes the direction of motion of an object. This means that
it acts in the opposite direction to motion.

direction
friction of motion

Friction acts between any two surfaces in contact.

When one surface moves over another, the force of friction acts between the surfaces and the
size of the force depends on the surfaces, e.g. a rough surface will give a lot of friction.

Air friction is usually called air resistance or drag. It depends mainly on two factors:
• the shape and size of the object
• the speed of the moving object.
Air resistance increases as the speed of movement increases (as the object accelerates).

����������������������������
����������������������������
����������������������������
N4 Increasing Friction
����������������������������
����������������������������
Where friction is used to slow an object down, it should be increased.
����������������������������
This can be achieved by:
����������������������������
• choosing surfaces which cause high friction e.g. sections of road before traffic lights
have higher friction than normal roads
• increasing the surface area and choosing a shape to increase air friction,
e.g. parachute.

Decreasing Friction

Where friction is making movement difficult, friction should be reduced.

This can be achieved by:
• lubricating the surfaces with oil or grease
• separating the surfaces with air, e.g. a hovercraft
• making the surfaces roll instead of slide, e.g. use ball bearings
• streamlining the shape of the object to reduce air friction (aerodynamic teardrop
shape).

����������������������������
����������������������������
����������������������������
����������������������������
����������������������������
����������������������������
����������������������������
 Newton’s Laws of Motion (1 and 2)
Balanced Forces
N4

A force is a vector quantity because to describe it properly requires a direction as well as size.

Two forces which are equal in size which act in opposite directions are called balanced forces.
engine
friction
force

When the engine force = friction on the car the forces are balanced.

Balanced forces have the same effect as having no forces acting at all.
����������������������������
����������������������������
����������������������������
���������������������������� Newton’s 1st Law of Motion
N4 N5
����������������������������
����������������������������
An object will remain at rest or travel in a straight line at a constant velocity (or speed) if the
forces are balanced. ����������������������������
����������������������������
���������������������������� engine
friction
����������������������������force
����������������������������
����������������������������

 If we consider the car moving in a straight line. If the engine force = friction, it will
continue to move at a constant velocity (or speed) in the same direction.
 If the same car is stationary (not moving) and all forces acting on it are balanced (same
as no force at all) the car will not move.

N4 Free Body Diagrams

We can use free body diagrams to analyse the forces on an object. This allows us to determine
the motion of the object.
Example: If the bus is travelling with an engine thrust of 12kN and all forces acting on the bus
are balanced
a) calculate the size of the frictional force acting
b) determine the motion of the bus.

Solution a) Draw the free body diagram

friction 12kN Since the forces are balanced
friction = 12kN

b) constant velocity (or speed) since the forces are balanced.

���������������������������
 Newton’s 2nd Law of Motion
N4 N5

This law deals with situations when there is an unbalanced force acting on the object.
The velocity cannot remain constant and the acceleration produced will depend on:
 the mass (m) of the object (a α 1/m) - if m increases a decreases and vice versa
 the unbalanced force (F) (a α F) - if F increases a increases and vice versa

This law can be summarised by the equation F = ma

T

N4 N5
Force, Mass and Acceleration Equation
����������������������������
A newton is defined as the force which makes a 1 kg mass accelerate at 1ms-2
����������������������������
����������������������������
����������������������������
From the definition: acceleration = unbalanced force
����������������������������
mass Quantity Symbol SI Unit
In symbol form: a = F F = ma m=F unbalanced
F N
force
m a
mass m kg

Example: Calculate the unbalanced force acting on a acceleration a ms-2

10000 kg bus accelerating at 3.5 ms-2.
F=? F = ma
m = 10000 kg F = 10000 x 3.5
-2
a = 3.5ms F = 35000 N

N5 Resultant Forces (1)

When several forces act on one object, they can be replaced by one force which has the same
effect. This single force is called the resultant or unbalanced force.

Example: Horizontal
A motorcycle and rider of combined mass 650 kg provide an engine force of 1200 N. The
friction between the road and motorcycle is 100N and the drag value = 200N.
Calculate:
a) the unbalanced force acting on the motorcycle
b) the acceleration of the motorcycle
200
N 1200N
Solution
100
a) Draw a free body diagram
N

F = 1200 - (200 + 100)

F = 900 N This 900 N force is the resultant of the 3 forces

b) F = 900 N F = ma Resultant Forces (2) in the vertical

a=? 900 = 650 x a direction will be considered in the
m = 650 kg a = 1.38 ms-2 Space Exploration section
xv
����������������������������F
 N5 Motion During Free Fall and Terminal Velocity

Free fall is the term used when an object is being acted upon only by the force of gravity
(weight).

However, free fall will cause the object to accelerate and from the section Introduction to
Friction, it states that:
air resistance will increase as an object accelerates

so we have to look at air resistance as well as weight to study motion during free fall.

Example: If we consider a sky diver jumping out of an aeroplane

A As he jumps B During Free Fall C Terminal Velocity

����������������������������
air resistance = 0 air resistance air resistance
����������������������������
����������������������������
����������������������������
����������������������������

weight weight weight

one force acting down weight > air resistance weight = air resistance

Unbalanced Force Unbalanced Force

downwards downwards Balanced Forces
(Newton’s 2nd law) (Newton’s 2nd law) (Newton’s 1st Law)

maximum decreasing acceleration = o

acceleration acceleration (constant velocity)

As the skydiver accelerates downwards, air resistance increases upwards until the value of air
resistance = the skydiver’s weight. This results in the two forces having the same value acting in
opposite directions. According to Newton’s 1st Law of Motion the skydiver will now travel at a
constant velocity. This velocity is known as Terminal Velocity.
 N5 Motion During Free Fall and Terminal Velocity (ctd)

The motion of the skydiver in the example is best illustrated in a velocity – time graph.
Refer to the previous page to fully understand what happens at points A, B and C.

����������������������������
v/ms-1
����������������������������
����������������������������
���������������������������� C
����������������������������
B

0 t/s

What do you think has happened to cause the motion represented by the dotted lines?
(Hint: How does the sky diver land on the ground safely?)
 Forces and Energy
N5 Energy

Energy cannot be destroyed, but it can be changed from one form into another. All forms of
energy are measured in the same unit: the joule (J).

When a force causes movement, some energy is changed from one form to another (it is
transformed) and we say that work is done.
For example, the force of friction causes kinetic energy to be transformed into heat.

N5 Work Done

The work done is a measure of the energy transformed. It is equal to the force multiplied by
the displacement (or distance) the force moves. The force and displacement (or distance) must
be measured in the same direction.

����������������������������

N5 Work, Force and Displacement Equation

From the definition:

Quantity Symbol SI Unit
Work done = force x displacement
work Ew J
force F N
In symbol form: s = Ew Ew = Fs F = Ew
displacement s m
F s

Example: A car of mass 700 kg brakes to a halt 15 m after the driver hits the brake.
If the breaking force = 1000 N, calculate the energy transferred (work done) by the
brakes.

Solution
Ew = ? Ew = F s
F = 1000 N Ew = 1000 x 15
s = 15 m Ew = 15000 J.
 Weight and Mass

N4 Weight

Weight is a force caused by gravity acting on an object’s mass. On Earth, it measures the
pull of the Earth on the object. It is measured in newtons (N).

Mass
Mass measures the amount of matter in an object. It is measured in kilograms (kg).
The value of mass does not change from place to place.

N4 N5 Weight, Mass and Gravitational Field Strength Equation

Weight always acts vertically downwards. Its size does not just depend on the mass of the
object, but on the strength of gravity at that place.
The strength of gravity in a particular place is called the gravitational field strength (g) and is
defined as the weight per unit mass. It is measured in Nkg-1. On Earth, g = 10 Nkg-1.

From the definition: Quantity Symbol SI Unit

gravitational field strength = weight weight W N
mass
mass m kg
In symbol form: g = W W = mg m=W gravitational
m g field g Nkg-1
strength

Example: A girl has a mass of 70 kg on Earth (g = 9.8 Nkg-1)

a) Calculate her weight on i) Earth and ii) the moon where g = 1.6 Nkg-1.
b) What is her mass on the moon?

Solution
a) i) W = ? W = mg ii) W = ? W = mg
m = 70 kg W = 70 x 9.8 m = 70 kg W = 70 x 1.6
g = 9.8 Nkg-1 W = 686 N -1
g = 1.6 Nkg W = 112 N

b) m = 70 kg (mass does not change)

 N5 W = m g Calculations - During Interplanetary Flight

The value for g is not always constant. It changes as you travel:

 further away from the centre of the earth;
 to a different planet, moon or star.

Every planet, moon and star has their own gravitational field strength.

Planet, Moon or Star Value for g / Nkg-1

Mercury 4
Venus 9
Earth 9.8
Earth’s Moon 1.6
Mars 4
Jupiter 26
Saturn 11
Uranus 11
Neptune 12
Sun 270

Example: An un-manned space rocket of mass 20000 kg travels from Earth to Mars, Jupiter,
Saturn and Uranus.
a) Calculate the rocket’s weight on Mars.
b) What is the mass of the rocket on Jupiter?
c) Of the 4 planets (including Earth) visited by the rockets, on which planets would the
weight of the rocket be the same? Explain your answer.

Solution
a) ) W = ? W = mg
m = 20000 kg W = 20000 x 4
g = 4 Nkg-1 W = 80000 N

b) m = 20000 kg
c) Saturn and Uranus. The values for g on both planets are the same with the mass of the
rocket remaining constant.

During interplanetary flight there is no need for the engines to be kept on. Since space is a
vacuum there is no friction acting on the space vehicle. With no unbalanced forces acting on
the vehicle it will continue to move at a steady velocity (Newton’s First Law of Motion).
 Newton’s Laws of Motion (3)

N5 Newton’s 3rd law of Motion

Newton noticed that forces occur in pairs. He called one force the action and the other the
reaction. These two forces are always equal in size, but opposite in direction. They do not
both act on the same object (do not confuse this with balanced forces).

Newton’s Third Law can be stated as:

If an object A exerts a force (the action) on object B, then object B will exert an equal,
but opposite force (the reaction) on object A.

For example:

a) Kicking a ball b) Rocket flight

Action Reaction

Action: The foot exerts a Action: The rocket pushes gases

force on the ball to out the back
the right Reaction: The gases push the rocket
Reaction: The ball exerts an in the opposite direction.
equal force on the
left to the foot
 1.3 Satellites and Projectiles
Satellites

N4 Satellites - Introduction

A satellite is an object which orbits another object.

The Moon is a natural satellite which orbits earth and Sputnik is a man made satellite as it was
put into an orbit of the earth.

The period of a satellite is the time taken for the satellite to complete one orbit.

The period of a satellite depends on the height of the satellite above the object it is orbiting.
The higher the orbit of the satellite the greater the period and vice versa.

N4 Geostationary Satellite

A geostationary satellite is a satellite which:

 has a period of 24 hours
 orbits at roughly 36000 km above the earth’s surface which is much higher than other
satellites
 stays above the same point on the earth’s surface at all times.

N4 Satellite Communication

Ground stations send microwave signals to the satellite using a curved dish transmitter to
transmit a strong signal. At the satellite the signal is collected by a curved dish receiver, then
amplified and finally retransmitted (at a different frequency) back to the ground using
another curved dish transmitter. The transmitting and receiving aerials are placed at the focal
point of the curved reflector.

The signal is sent at a speed of 300 000 000 ms-1. This allows the equation d = vt to be used
with satellite communication.
satellite

ground
ground station
station
 N4
Satellite Communication – Parabolic (Curved) Reflectors

Receiving the signal Transmitting the signal

receiving transmitting
aerial aerial

curved
reflector curved
reflector
Curved reflectors are used to Curved reflectors are also used
increase the strength of a on certain transmitters to
received signal from a satellite or transmit a strong, parallel signal
other source. The curved shape beam. In a dish transmitter the
of the reflector collects the signal transmitting aerial is placed at
over a large area and brings it to the focus and the curved shape
a focus. The receiving aerial is of the reflector produces a
placed at the focus so that it parallel signal beam.
receives a strong signal.

N4 Applications of Satellites

Satellites are being used by many countries in different ways. For example:
 Sending a television or radio signal across the country or to another country
The Olympic Games can be beamed around the world using satellite communication.
Three geostationary satellites, placed in orbit above the equator permits worldwide
communication with satellites communicating with ground stations in different
continents.
 Navigation
There are many Global Positioning Satellite (G.P.S) systems available to put in a car so
that you don’t get lost. This uses the basic equation d = vt to establish your position.
 Weather monitoring
The weather satellite is a type of satellite that is primarily used to monitor the weather
and climate of the Earth.
 N4 N5 Using Satellites to Monitor Global Change

Global environmental change is one of the most pressing international concerns of the 21st
century. For many years, various types of satellites have been used to detect and monitor
worldwide changes including:
 the effects of global warming
 depletion in the ozone layer and
 large scale changes in land cover.

These changes have been down to both:

 natural occurrences and
 as a consequence of the impact of our actions.

Satellites which are used to monitor such events orbit at heights much smaller than 36000 km
and do not stay above the same point on the Earth’s surface. This allows continuous
observation and monitoring of the Earth's land, atmosphere, oceans and ice caps.
For example, the 2002 oil spill off the northwest coast of Spain was watched carefully by the
European ENVISAT satellite, which, though not a weather satellite, flies an instrument (ASAR)
which can see changes in the sea surface. It orbits at a height of approximately 800 km. With
this information collected by the satellite, rescue teams and environmental agencies can attend
the scene quickly and minimise the damage caused.
Other disasters, both natural and otherwise can be detected and monitored in a similar way.
 Projectiles

N5 Projectile Motion

A projectile is an object which has been given a forward motion through the air, but which is
also pulled downward by the force of gravity.
This results in the trajectory (path) of the projectile being curved.
For example, a cannon firing a cannonball will result in the cannonball following a curved
trajectory as shown below.

A projectile has two separate motions at right angles to each other - horizontal and vertical.
Each motion is independent of the other.

Points to note:
 The horizontal motion is at a constant velocity since there are no forces acting
horizontally if air resistance can be ignored (Newton’s first law of motion).
Horizontal displacement = horizontal velocity x time in the air (s = v t)
 The vertical motion is one of constant acceleration, equal to the value of g.
For projectiles which are projected horizontally, the initial vertical velocity is zero.
For vertical calculations, use v = u + at, where u = 0 and a = g (= 9.8ms-2 on Earth).

Example: Using formulae

A ball is kicked horizontally at 5 ms-1 from a cliff top as shown below. It takes 2 seconds to
reach the ground.

a) How far does the ball travel horizontally in 2 seconds?

b) What was its vertical velocity just before it hit the ground?

Solution
a) Horizontal b) Vertical
s =? v=?
v = 5ms-1 u=0
t=2s a = 9.8 ms-2 (= g on Earth)
t = 2s (time is the same for vertical and horizontal motion)

s=vt v = u + at
s=5x2 v = 0 + (9.8 x 2)
s = 10 m v = 19.6 ms-1
 N5 Projectile Motion (ctd)

Example: Using Graphs

A bird flying horizontally at a constant velocity drops a fish it is carrying into a lake.
The velocity - time graphs for both the horizontal and vertical motion of the fish from when it
is dropped until it hits the water are shown below.
Horizontal Vertical
-1 -1
v/ms v/ms
20

0 4 t/s 0 4 t/s
Calculate
a) The horizontal velocity when it hits the water.
b) The vertical velocity when it hits the water.
c) The horizontal displacement of the fish travelled after it was dropped.
d) The height the osprey was flying when it dropped the fish.

Solution

a) Horizontal velocity = 20 ms-1 (horizontal velocity remains constant throughout).

b) Vertical
v=? v = u + at
u=0 v = 0 + (9.8 x 4)
a = 10 ms-2 v = 39.2 ms-1
t=3s

c) Horizontal displacement = area under the horizontal velocity - time graph

= area of rectangle
= 20 x 4
= 80 m.

d) Height = area under the vertical velocity - time graph

= area of triangle
= ½ x 40 x 4
= 80 m.

N5 Satellites – An Application of Projectile Motion

Satellite motion is an application of projectile motion. A satellite is continually accelerating

vertically towards the ground just like any other projectile. However, the satellite is moving so
fast horizontally that the Earth curves away from it as quickly as it falls. This means that the
satellite never reaches the earth but continues to move in orbit.
 1.4 Cosmology
The Universe
N4 Cosmic Definitions

There are many different bodies moving around in the universe. Below is a list of some of them
with a definition of what they are:
 Star A hot ball of matter which is undergoing nuclear fusion emitting
light. The sun is an example of a star.

 Planet A spherical ball of rock and / or gas which orbits a star.

Earth is an example of a planet.

 Moon A lump of matter which orbits a planet.

Our moon orbits Earth. Deimos which orbits Mars is another
example of a moon.

 Solar System A solar system consists of a star and all the objects orbiting it as
well as all the material in that system.
Our Solar System includes the Sun together with the eight planets
and their moons as well as all other celestial bodies that orbit the
sun.

 Galaxy A large cluster of stars, some of which have planets orbiting them.
The Milky Way is an example of a galaxy.

 Exo Planet A planet outside our Solar System.

(or Extrasolar In 2009, there were between 220 and 350 reported exo planets
Planet) depending on the criteria used by the counting organisation.

 The Universe Consists of many Galaxies separated by empty space.

 N4 Life on an Exo Planet?

If you consider the growing population and dwindling resources of our home planet, some
scientists believe that finding exo planets capable of sustaining life should be a top priority.
Scientists need to consider the basic needs of life and if these needs can be delivered by an exo
plant.
The basic needs for human life are:
 Oxygen
 Water
 Food
 Shelter
 Warmth.

In our search for a new home scientists need to identify an exo planet which has:
 A similar atmosphere to ours
 The potential to build shelter
 The potential to grow and nurture a sustainable food source.

The next problem once the exo planet has been identified is how to get there!

N4 N5 Light Year

Contrary to the name, a light year is a measure of distance and not time.

1 light year is the distance light travels in 1 year.

Light is an electromagnetic wave which travels at a speed of 300 000 000 ms -1.

Question
How far does light travel in one year?
d=? d=vt
v = 300 000 000 ms-1 d = 300 000000 x 31 536 000
t = 1 x 365 x 24 x 60 x 60 = 31 536 000 s d = 9 460 800 000 000 000 m

one light year = 9 460 800 000 000 000 m

As the distances in the universe are very large we need to use the term light year instead of
metres or even miles. Below are distances you will be required to know.

Approximate distance from Earth to:

 The Sun – 0.000016 light years (or 8.3 light minutes)
 Proxima Centauri (nearest star outside the solar system) – 4.2 light years
 Canis Major Dwarf (nearest galaxy to the Milky Way) – 25000 light years
 The edge of the known Universe – 46 billion light years.
 Cosmogony
N5 The Big Bang Theory (The Theory of the Origin of the Universe)

Most astronomers believe the Universe began in a Big Bang about 14 billion years ago. At that
time, the entire Universe was inside a bubble that was thousands of times smaller than a
pinhead. It was hotter and denser than anything we can imagine.

Contrary to the name, astronomers believe that there was no explosion. The ‘bubble’ began to
expand and the Universe that we know was born. Time, space and matter all began with the Big
Bang. In a fraction of a second, the Universe grew from smaller than a single atom to bigger
than a galaxy and it kept on growing at a fantastic rate. It is still expanding today.

As the Universe expanded and cooled, energy changed into particles of matter and antimatter.
These two opposite types of particles largely destroyed each other. But some matter survived.
More stable particles called protons and neutrons started to form when the Universe was one
second old.

Over the next three minutes, the temperature dropped below 1 billion degrees Celsius. It was
now cool enough for the protons and neutrons to come together, forming hydrogen and helium
nuclei.

After 300 000 years, the Universe had cooled to about 3000 degrees. Atomic nuclei could finally
capture electrons to form atoms. The Universe filled with clouds of hydrogen and helium gas.
From these clouds, galaxies and solar systems formed.

N5 Evidence to Support the Big Bang Theory

Scientists are reasonably certain that the universe had a beginning. This is the basis of the Big
Bang Theory. To support this argument scientists have discovered that:
 Galaxies appear to be moving away from us at speeds proportional to their distance.
This observation supports the expansion of the universe and suggests that the universe
was once compacted.
 If the universe was initially very, very hot as the Big Bang suggests, we should be able to
find some small remains of this heat. In 1965, Radio astronomers discovered Cosmic
Microwave Background radiation (CMB) which spread throughout parts of the
observable universe. This is thought to be the small remains which scientists were
looking for.
 Finally, the abundance of the "light elements" Hydrogen and Helium found in the
observable universe are thought to support the Big Bang model of origins.

As mentioned above, the Big Bang occurred about 14 billion years ago. Scientists estimate this
by:
 Looking for the oldest stars
 Measuring the expansion of the universe.
 The Electromagnetic Spectrum

N5 Electromagnetic Radiations

There is a group of radiations which have given astronomers a vast amount of information on
the Universe. These radiations make up The Electromagnetic Spectrum.

Like all the notes on a piano, they are grouped in an order according to their frequency.

In unit 3 you will learn what frequency and wavelength means in Physics but all you have to
know in unit 1 is the order in which these radiations fall in terms of their frequency and
wavelength.

All these radiations travel at the speed of light = 300 000 000 ms-1.

The 7 radiations are listed below:

Radio and TV waves

Micro waves

Infra Red (heat)

Increasing Increasing
wavelength frequency
Visible light

Ultra Violet

X-Rays

Gamma rays

How do I remember this?

Rabbits Mate In Very Unusual eXpensive Gardens

Can you think of your own pneumonic to remember The Electromagnetic Spectrum?
 N5 Detectors of Electromagnetic Radiations

Humans can detect some of the electromagnetic radiations e.g. the eyes can detect visible light,
infra red can be detected by skin and sun burn is a consequence of the skin being over exposed
to ultra violet radiation from the sun.

However, energy is given out by objects in space (e.g. stars or galaxies) over the whole range of
the electro-magnetic spectrum so to fully understand the universe we must collect information
at all these wavelengths. Different kinds of telescope are therefore required to detect different
wavelengths of radiation as one as alone cannot detect them all.

Below is a list of detectors for each radiation in the spectrum.

Radiation Detector Use

Gives information on
Radio and T.V Aerial different planets e.g.
distance from the Earth
The detection of Cosmic
Microwave Background
Micro waves Diode probe
consolidated the belief the
Big Bang occurred
Infra red is used to detect
Blackened
Infra Red objects just outside the
thermometer
visible spectrum
Gives information on planets
Visible Light Photographic film and stars including
temperature and size
Used to study star formation
Ultra Violet Fluorescent paint – most “young” stars emit
ultra violet radiation
Used to detect the presence
X-Rays Photographic film
of black holes
Used to detect the presence
Gamma rays Geiger-Muller tube
of black holes and supernova
 Spectroscopy

N5 Continuous and Line Spectra

Astronomers can find out information about stars from the light the star emits using an
instrument called a spectroscope.
The spectroscope splits up the light to produce a spectrum.
There are two types of spectra:

 Continuous – produced by light from solids, liquids and gases at high pressure and at
high temperature. Each colour in the spectrum has a different frequency and
wavelength

 Line – produced by hot gases at low pressure and gases which have an electric current
passed through them. Each line in the spectrum corresponds to a particular frequency
and wavelength.

Line spectra are extremely useful for astronomers because every chemical element has its own
unique spectrum (like D.N.A or fingerprints). This allows astronomers to identify elements
present in distant stars.

You may find this easier to understand after looking at the example on the next page.
 N5
Stellar Detectives

Example: Identify the elements that make up the unknown star from the line spectra below.
The line spectra for hydrogen, helium, sodium and calcium are given below to help you.

Unknown star

Hydrogen

Helium

Sodium

Calcium

Answer : Hydrogen and Helium.

All spectral lines present in Hydrogen and Helium are present in the unknown star.
 1.5 Space Exploration
Heading into Space

N4 N5 What We Have Learned by Heading into Space?

Read any debate about space exploration, and this question will invariably come up.

“Why should we be spending money exploring space when there are so many problems here on
Earth that we need to solve first?”
It’s a tricky one.

One answer is that reaching for new heights often creates new solutions, new opportunities
and elevates hope back on the ground.

We have learned so much about our own planet and the expanding universe by exploring space.
If mankind had not explored space and used telescopes then we would not have found out the
following about:

The Earth
 A greater understanding about the rotation of the Earth, the orbit of the Earth around
the Sun and how this affects time on earth. e.g. one rotation of the Earth is one day, one
orbit of the Sun by the Earth is one year etc.
 It has allowed meteorologists to predict and monitor of the weather. Satellites have
been put into orbit to monitor the Earth’s weather systems and allows us to predict
natural disasters e.g. tsunamis and hurricanes
 Allowed the monitoring of the polar ice caps and enabled a plan to be put in place to
minimise their erosion and prepare for the consequences of the erosion i.e. rising water
levels and the destruction of natural habitats for polar animals.

The Universe
 Greater understanding of the origin of the Universe
 The Universe is still expanding
 Estimate the age of the universe

Through exploration our understanding of the Universe has changed. There were a few
misconceptions before our understanding shaped our belief of the expanding universe and the
model of it we have today. Scientists at certain times thought:

 The Earth was thought to be flat - it's round.

 The Earth was thought to be the centre of the Universe (see diagram below) - it's not.
 The Sun was thought to be the centre of the Universe - it's not.
 The Milky Way was thought to be the centre of the Universe - It's not.
 The centre of the Universe was thought to have a definite location - it doesn't.
 N5 Evidence to Support our Understanding of the Universe

From an earlier section titled ‘The Big Bang Theory’, it is stated that Physicists thought that at
one second old, stable particles called protons and neutrons started to form. These particles
form our model of the nucleus of the atom. However, something was missing from that model
called the Higgs Boson. Professor Higgs, a British physicist wrote in 1969 that the Higgs Boson's
role is to give the particles that make up atoms their mass. Without this mass, they would zip
around the cosmos, unable to bind together to form the atoms that make stars and planets –
and people.
On 4th July 2012, Physicists working at CERN at the world’s largest particle accelerator – The
Large Hadron Collider – announced the discovery of the Higgs Boson – further evidence to
support our understanding of the universe.
Some Physicists relate this finding to other landmarks in Scientific history e.g. Neil Armstrong
walking on the moon.
 The Space Rocket

N5 Resultant Forces (2)

Resultant forces in the horizontal direction was studied in the Forces section (1.2).
In this section we will consider resultant forces in the vertical direction in the context of a space
rocket launching. In this section we will also consider the forces acting on the rocket during
flight and when landing. This involves Newton’s 1st, 2nd and 3rd laws of motion and the weight
of the rocket (W = mg).

Example 1 - Launching

At launch, a rocket of mass 20 000 kg accelerates off the ground at 12 ms-2 (ignore air
resistance)
a) Use Newton’s 3rd law of motion to explain how the rocket gets off the ground.
b) Draw a free body diagram to show all the vertical forces acting on the rocket as it
accelerates upwards.
c) Calculate the engine thrust of the rocket which causes the acceleration of 12ms-2.

Solutions
a) The rocket pushes the gas out the back downwards (action) and the gas pushes the
rocket upwards (reaction).
b)

Engine thrust

Weight
c) Calculate F and W
F=ma
F = 20 000 x 12 Engine thrust = ?
F = 240 000 N

W=mg
W = 20 000 x 9.8
F = ma
W = 196 000 N m = 20000 kg

F = upward force (thrust) – downwards force (Weight)

240 000 = thrust – 196 000
thrust = 436 000 N
W = mg
 N5 Resultant Forces (2) (ctd)

Example 2 – During Flight

The same rocket reaches a speed of 10 000 ms-1 as it accelerates away from earth.
a) Can you suggest 3 reasons why the acceleration of the rocket will increase? (Hint: this
time take into consideration air resistance)
b) When the rocket is in space there is negligible gravity acting on it. Use all of Newton’s
laws of motion to explain how the rocket moves in space.

Solution
a)
 Decrease in mass due to fuel being used up
 Decrease in air resistance as there is less air particles the further away from the
surface of the Earth
 Decrease in the value of g the further away from the centre of the Earth

b) Travelling at a constant speed – all thrusters are switched off and forces or both forward
and backward thrusters are on applying the same force. In both situations the forces are
balanced (1st Law)
Accelerating – forward thrusters on and the forces are unbalanced in the forward
direction (2nd law)
Decelerating – backward thrusters on and the forces are unbalanced in the backward
direction (2nd law)
When the thrusters are on they propel the gases out (action) which applies a force to
the rocket in the opposite direction (reaction) (3rd law)

Example 3 – Landing

On returning from space the rocket has to overcome two major hurdles:
 Re-enter the Earth’s atmosphere
 Land safely on the ground

a) As the rocket enters the earth’s atmosphere what happens to it’s velocity?
b) Explain your answer to part a)
c) What is the main energy change during re-entry (think back to S1 Energy topic)?
d) When the rocket touches down on the ground, explain in terms of forces why a
parachute is activated out the back of the rocket to bring it to a safe stop.

Solution
a) It decreases
b) The rocket is travelling so fast (at around 8000 ms-1) as it passes into the atmosphere air
so a large frictional force will act against it.
c) Kinetic to heat
d) When the parachute opens, the force due to air resistance (drag) drastically increases
and causes an unbalanced force acting backwards against motion. This will result in the
rocket decelerating and eventually coming to a safe stop.
 Space Technology

N5 Made in Space for Us – The Benefits of Space Exploration

Space technology is not limited to be used in space. There are many items that benefit us in our
day to day lives which have evolved from equipment used and created for use in space
exploration.
The following pieces of equipment have been developed and improved upon as a result of
space exploration:
 Artificial limbs - Innovations in robotics and shock-absorption/comfort materials are
inspiring and enable the private sector to create new and better solutions for animal and
human artificial limbs.
 Ear thermometers - A thermometer which weighs only 8 ounces was developed which
uses infrared astronomy technology to measure the amount of heat energy emitted by
the eardrum, the same way the temperature of stars and planets is measured.
 Water purification - This system, makes use of available resources by turning
wastewater from respiration, sweat, and urine into drinkable water. Commercially, this
system is benefiting people all over the world who need affordable, clean water.
 Heat resistant paints - The spacecraft Apollo’s heat shield was coated with a material
whose purpose was to burn and thus dissipate energy during re-entry while charring, to
form a protective coating to block heat penetration. This led to the development of
other applications of the heat shield, such as fire-retardant paints and foams for aircraft.
 Re-entry

N5 Changes of State

Energy added

freezing condensing

Solid Liquid Gas

melting evaporating
(fusing)

Energy given out

 During a change of state, energy is either added or given out as shown in the diagram
above
 During a change of state, there is no change in temperature until the change of state of
state is complete.

N5 Specific Heat Capacity

The specific heat capacity of a material is defined as the amount of energy required or given out
when 1 kg of a substance changes in temperature by 1 oC without changing the state of the
substance.

Specific Latent Heat of Vapourisation

The specific latent heat of vapourisation is defined as the amount of energy required or given
out when 1 kg of a substance changes state from a liquid to a gas or a gas to a liquid without
changing the temperature of the substance.

Specific Latent Heat of Fusion

The specific latent heat of fusion is defined as the amount of energy required or given out when
1 kg of a substance changes state from a solid to a liquid or a liquid to a solid without changing
the temperature of the substance.

Latent heat will be studied in more detail in the Electricity and Energy unit.
 N5 Specific Heat Capacity, Energy, Mass and Change in
Temperature Equation

From the definition specific heat capacity = heat energy

mass x change in temperature

In symbol form : c = EH EH = c m ∆T m = EH ∆T = EH
m ∆T c ∆T cm

Quantity Symbol SI Unit

Heat Energy EH J
Specific Heat
c J kg-1 oC-1
Capacity
mass m kg
Change in o
∆T C
temperature

Example: How much heat is required to increase the temperature of 1.5 kg of concrete from
30 oC to 50 oC? (cconcrete = 800 Jkg-1 oC-1)
Solution:
EH = ? EH = c m ∆T
-1 o -1
c = = 800 Jkg C EH = 800 x 1.5 x 20
m = 1.5 kg EH = 24 000 J
o
∆T = 50 – 30 = 20 C

N5 Challenges During Re-entry

When a space craft returns from space it re-enters the Earth’s atmosphere.
There are many challenges associated with re-entry and two are listed below:
 Rise in temperature due to friction
The craft is travelling at around 8000ms-1 so a large frictional force acts on it due to the
air in the atmosphere. This results in the space craft
slowing down. The frictional force causes a rise in
temperature which is a problem for the craft. The
space craft uses special silica tiles to protect it
and the bottom and leading edge are covered with
black reinforced carbon. These materials which make
up the Thermal Protection System are designed
to absorb large quantities of heat without increasing
their temperature very much. In other words, they have a high specific heat capacity.
The peak skin temperature, on the underside of the wings close to the leading
edges, is around 1600°C - hot enough to melt steel.
 The angle of re-entry
If the angle of approach is too steep, frictional heating will be too fast and burn the
spacecraft up. If the angle of approach is too shallow the spacecraft will skip off the
atmosphere into a highly elliptical orbit which will take it far from the Earth (think about
skipping a stone across a pond). There is thus an optimum angle for re-entry.
 Risks Associated with Space Exploration

N5 Risks

Human spaceflight is both risky and expensive. From the crash landing of the first manned
Soyuz spacecraft in 1967 to the explosion of the shuttle orbiter Columbia in 2003, 18 people
died during spaceflights. Providing the systems to support people while in orbit adds significant
additional costs to a space mission, and ensuring that the launch, flight, and re-entry are carried
out as safely as possible also requires highly reliable and thus costly equipment, including both
spacecraft and launchers.