Conforms to Regulation (EC) No.

1907/2006 (REACH), Annex II, as amended by Regulation (EU)

No. 2015/830

SAFETY DATA SHEET

Date of issue/Date of revision : 3 February 2020 Version : 1.03

SECTION 1: Identification of the substance/mixture and of the company/

undertaking
1.1 Product identifier
Product name : SIGMA EP 159 SEALER BASE
Product code : 00239839
Product type : Liquid.
Other means of identification
Not available.

1.2 Relevant identified uses of the substance or mixture and uses advised against
Product use : Professional applications, Used by spraying.
Use of the substance/ : Coating.
mixture
Uses advised against : Product is not intended, labelled or packaged for consumer use.

1.3 Details of the supplier of the safety data sheet

Sigma Paint Saudi Arabia Ltd.
PO Box 7509
Dammam 31472
Saudi Arabia
Tel: 00966 138 47 31 00
Fax: 00966 138 47 17 34

e-mail address of person : [email protected]

responsible for this SDS

1.4 Emergency telephone : 00966 138473100 extn 1001

number

SECTION 2: Hazards identification

2.1 Classification of the substance or mixture
Product definition : Mixture
Classification according to Regulation (EC) No. 1272/2008 [CLP/GHS]
Flam. Liq. 3, H226
Skin Irrit. 2, H315
Eye Dam. 1, H318
Skin Sens. 1, H317
STOT SE 3, H335
The product is classified as hazardous according to Regulation (EC) 1272/2008 as amended.
See Section 16 for the full text of the H statements declared above.
See Section 11 for more detailed information on health effects and symptoms.

2.2 Label elements

Hazard pictograms :

English (GB) United Arab Emirates 1/14

Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II
Code : 00239839 Date of issue/Date of revision : 3 February 2020
SIGMA EP 159 SEALER BASE

SECTION 2: Hazards identification

Signal word : Danger
Hazard statements : Flammable liquid and vapour.
Causes serious eye damage.
Causes skin irritation.
May cause an allergic skin reaction.
May cause respiratory irritation.
Precautionary statements
Prevention : Wear protective gloves. Wear protective clothing. Wear eye or face protection.
Keep away from heat, hot surfaces, sparks, open flames and other ignition sources.
No smoking. Avoid breathing vapour.
Response : IF INHALED: Remove person to fresh air and keep comfortable for breathing. IF ON
SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water.
IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses,
if present and easy to do. Continue rinsing.
Storage : Store in a well-ventilated place. Keep cool.
Disposal : Not applicable.
Hazardous ingredients : xylene
Epoxy Resin (700<MW<=1100)
2-methylpropan-1-ol
Supplemental label : Not applicable.
elements
Annex XVII - Restrictions : Not applicable.
on the manufacture,
placing on the market and
use of certain dangerous
substances, mixtures and
articles
Special packaging requirements
Containers to be fitted : Not applicable.
with child-resistant
fastenings
Tactile warning of danger : Not applicable.

2.3 Other hazards

Product meets the criteria : This mixture does not contain any substances that are assessed to be a PBT or a
for PBT or vPvB vPvB.
Other hazards which do not : Prolonged or repeated contact may dry skin and cause irritation.
result in classification

SECTION 3: Composition/information on ingredients

3.2 Mixtures : Mixture
Classification
Product/ingredient name Identifiers % by weight Regulation (EC) No. Type
1272/2008 [CLP]
xylene REACH #: 01-2119488216-32 ≥25 - ≤49 Flam. Liq. 3, H226 [1] [2]
EC: 215-535-7 Acute Tox. 4, H312
CAS: 1330-20-7 Acute Tox. 4, H332
Index: 601-022-00-9 Skin Irrit. 2, H315
Eye Irrit. 2, H319
STOT SE 3, H335
Asp. Tox. 1, H304
Epoxy Resin (700<MW<=1100) CAS: 25036-25-3 ≥25 - ≤50 Skin Irrit. 2, H315 [1]
Eye Irrit. 2, H319
English (GB) United Arab Emirates 2/14
Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II
Code : 00239839 Date of issue/Date of revision : 3 February 2020
SIGMA EP 159 SEALER BASE

SECTION 3: Composition/information on ingredients

Skin Sens. 1, H317
2-methylpropan-1-ol REACH #: 01-2119484609-23 ≥5.0 - ≤10 Flam. Liq. 3, H226 [1] [2]
EC: 201-148-0 Skin Irrit. 2, H315
CAS: 78-83-1 Eye Dam. 1, H318
Index: 603-108-00-1 STOT SE 3, H335
STOT SE 3, H336
ethylbenzene REACH #: 01-2119489370-35 ≥5.0 - ≤8.8 Flam. Liq. 2, H225 [1] [2]
EC: 202-849-4 Acute Tox. 4, H332
CAS: 100-41-4 STOT RE 2, H373
Index: 601-023-00-4 (hearing organs)
Asp. Tox. 1, H304
Hydrocarbons, C10-C13, n- REACH #: 01-2119457273-39 ≥1.0 - ≤5.0 Asp. Tox. 1, H304 [1]
alkanes, isoalkanes, cyclics, < 2% EC: 918-481-9 EUH066
aromatics CAS: 64742-48-9 (EC
918-481-9)
toluene REACH #: 01-2119471310-51 ≤0.30 Flam. Liq. 2, H225 [1] [2]
EC: 203-625-9 Skin Irrit. 2, H315
CAS: 108-88-3 Repr. 2, H361d (Unborn
Index: 601-021-00-3 child)
STOT SE 3, H336
STOT RE 2, H373
Asp. Tox. 1, H304
See Section 16 for the full text of the H statements declared above.
There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations
applicable, are classified as hazardous to health or the environment, are PBTs, vPvBs or Substances of equivalent
concern, or have been assigned a workplace exposure limit and hence require reporting in this section.
Type
[1] Substance classified with a health or environmental hazard
[2] Substance with a workplace exposure limit
[3] Substance meets the criteria for PBT according to Regulation (EC) No. 1907/2006, Annex XIII
[4] Substance meets the criteria for vPvB according to Regulation (EC) No. 1907/2006, Annex XIII
[5] Substance of equivalent concern
[6] Additional disclosure due to company policy
Occupational exposure limits, if available, are listed in Section 8.
SUB codes represent substances without registered CAS Numbers.

SECTION 4: First aid measures

4.1 Description of first aid measures
Eye contact : Check for and remove any contact lenses. Immediately flush eyes with running water
for at least 15 minutes, keeping eyelids open. Seek immediate medical attention.
Inhalation : Remove to fresh air. Keep person warm and at rest. If not breathing, if breathing is
irregular or if respiratory arrest occurs, provide artificial respiration or oxygen by
trained personnel.
Skin contact : Remove contaminated clothing and shoes. Wash skin thoroughly with soap and
water or use recognised skin cleanser. Do NOT use solvents or thinners.
Ingestion : If swallowed, seek medical advice immediately and show the container or label. Keep
person warm and at rest. Do NOT induce vomiting.
Protection of first-aiders : No action shall be taken involving any personal risk or without suitable training. If it is
suspected that fumes are still present, the rescuer should wear an appropriate mask
or self-contained breathing apparatus. It may be dangerous to the person providing
aid to give mouth-to-mouth resuscitation. Wash contaminated clothing thoroughly
with water before removing it, or wear gloves.

4.2 Most important symptoms and effects, both acute and delayed
Potential acute health effects

English (GB) United Arab Emirates 3/14

Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II
Code : 00239839 Date of issue/Date of revision : 3 February 2020
SIGMA EP 159 SEALER BASE

SECTION 4: First aid measures

Eye contact : Causes serious eye damage.
Inhalation : May cause respiratory irritation.
Skin contact : Causes skin irritation. Defatting to the skin. May cause an allergic skin reaction.
Ingestion : No known significant effects or critical hazards.
Over-exposure signs/symptoms
Eye contact : Adverse symptoms may include the following:
pain
watering
redness
Inhalation : Adverse symptoms may include the following:
respiratory tract irritation
coughing
Skin contact : Adverse symptoms may include the following:
pain or irritation
redness
dryness
cracking
blistering may occur
Ingestion : Adverse symptoms may include the following:
stomach pains

4.3 Indication of any immediate medical attention and special treatment needed
Notes to physician : Treat symptomatically. Contact poison treatment specialist immediately if large
quantities have been ingested or inhaled.
Specific treatments : No specific treatment.

SECTION 5: Firefighting measures

5.1 Extinguishing media
Suitable extinguishing : Use dry chemical, CO₂, water spray (fog) or foam.
media

Unsuitable extinguishing : Do not use water jet.

media

5.2 Special hazards arising from the substance or mixture

Hazards from the : Flammable liquid and vapour. Runoff to sewer may create fire or explosion hazard.
substance or mixture In a fire or if heated, a pressure increase will occur and the container may burst, with
the risk of a subsequent explosion.
Hazardous combustion : Decomposition products may include the following materials:
products carbon oxides
metal oxide/oxides

5.3 Advice for firefighters

Special precautions for fire- : Promptly isolate the scene by removing all persons from the vicinity of the incident if
fighters there is a fire. No action shall be taken involving any personal risk or without suitable
training. Move containers from fire area if this can be done without risk. Use water
spray to keep fire-exposed containers cool.
Special protective : Fire-fighters should wear appropriate protective equipment and self-contained
equipment for fire-fighters breathing apparatus (SCBA) with a full face-piece operated in positive pressure
mode. Clothing for fire-fighters (including helmets, protective boots and gloves)
conforming to European standard EN 469 will provide a basic level of protection for
chemical incidents.

English (GB) United Arab Emirates 4/14

Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II
Code : 00239839 Date of issue/Date of revision : 3 February 2020
SIGMA EP 159 SEALER BASE

SECTION 6: Accidental release measures

6.1 Personal precautions, protective equipment and emergency procedures
For non-emergency : No action shall be taken involving any personal risk or without suitable training.
personnel Evacuate surrounding areas. Keep unnecessary and unprotected personnel from
entering. Do not touch or walk through spilt material. Shut off all ignition sources.
No flares, smoking or flames in hazard area. Do not breathe vapour or mist. Provide
adequate ventilation. Wear appropriate respirator when ventilation is inadequate.
Put on appropriate personal protective equipment.
For emergency responders : If specialised clothing is required to deal with the spillage, take note of any
information in Section 8 on suitable and unsuitable materials. See also the
information in "For non-emergency personnel".

6.2 Environmental : Avoid dispersal of spilt material and runoff and contact with soil, waterways, drains
precautions and sewers. Inform the relevant authorities if the product has caused environmental
pollution (sewers, waterways, soil or air).

6.3 Methods and material for containment and cleaning up

Small spill : Stop leak if without risk. Move containers from spill area. Use spark-proof tools and
explosion-proof equipment. Dilute with water and mop up if water-soluble.
Alternatively, or if water-insoluble, absorb with an inert dry material and place in an
appropriate waste disposal container. Dispose of via a licensed waste disposal
contractor.
Large spill : Stop leak if without risk. Move containers from spill area. Use spark-proof tools and
explosion-proof equipment. Approach the release from upwind. Prevent entry into
sewers, water courses, basements or confined areas. Wash spillages into an
effluent treatment plant or proceed as follows. Contain and collect spillage with non-
combustible, absorbent material e.g. sand, earth, vermiculite or diatomaceous earth
and place in container for disposal according to local regulations. Dispose of via a
licensed waste disposal contractor. Contaminated absorbent material may pose the
same hazard as the spilt product.
6.4 Reference to other : See Section 1 for emergency contact information.
sections See Section 8 for information on appropriate personal protective equipment.
See Section 13 for additional waste treatment information.

SECTION 7: Handling and storage

The information in this section contains generic advice and guidance. The list of Identified Uses in Section 1 should be
consulted for any available use-specific information provided in the Exposure Scenario(s).
7.1 Precautions for safe handling
Protective measures : Put on appropriate personal protective equipment (see Section 8). Eating, drinking
and smoking should be prohibited in areas where this material is handled, stored and
processed. Workers should wash hands and face before eating, drinking and
smoking. Remove contaminated clothing and protective equipment before entering
eating areas. Do not ingest. Avoid contact with eyes, skin and clothing. Avoid
breathing vapour or mist. Use only with adequate ventilation. Wear appropriate
respirator when ventilation is inadequate. Do not enter storage areas and confined
spaces unless adequately ventilated. Keep in the original container or an approved
alternative made from a compatible material, kept tightly closed when not in use.
Store and use away from heat, sparks, open flame or any other ignition source. Use
explosion-proof electrical (ventilating, lighting and material handling) equipment. Use
non-sparking tools. Take precautionary measures against electrostatic discharges.
To avoid fire or explosion, dissipate static electricity during transfer by earthing and
bonding containers and equipment before transferring material. Empty containers
retain product residue and can be hazardous. Do not reuse container.

English (GB) United Arab Emirates 5/14

Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II
Code : 00239839 Date of issue/Date of revision : 3 February 2020
SIGMA EP 159 SEALER BASE

SECTION 7: Handling and storage

Advice on general : Eating, drinking and smoking should be prohibited in areas where this material is
occupational hygiene handled, stored and processed. Workers should wash hands and face before eating,
drinking and smoking. Remove contaminated clothing and protective equipment
before entering eating areas. See also Section 8 for additional information on
hygiene measures.

7.2 Conditions for safe : Store between the following temperatures: 0 to 35°C (32 to 95°F). Store in
storage, including any accordance with local regulations. Store in a segregated and approved area. Store
incompatibilities in original container protected from direct sunlight in a dry, cool and well-ventilated
area, away from incompatible materials (see Section 10) and food and drink. Store
locked up. Eliminate all ignition sources. Separate from oxidizing materials. Keep
container tightly closed and sealed until ready for use. Containers that have been
opened must be carefully resealed and kept upright to prevent leakage. Do not store
in unlabelled containers. Use appropriate containment to avoid environmental
contamination. See Section 10 for incompatible materials before handling or use.

7.3 Specific end use(s)

See Section 1.2 for Identified uses.
Recommendations : Not available.
Industrial sector specific : Not available.
solutions

SECTION 8: Exposure controls/personal protection

The information in this section contains generic advice and guidance. The list of Identified Uses in Section 1 should be
consulted for any available use-specific information provided in the Exposure Scenario(s).
8.1 Control parameters
Occupational exposure limits
Product/ingredient name Exposure limit values

xylene EU OEL (Europe, 2/2017). Absorbed through skin.

STEL: 442 mg/m³ 15 minutes.
STEL: 100 ppm 15 minutes.
TWA: 221 mg/m³ 8 hours.
TWA: 50 ppm 8 hours.
2-methylpropan-1-ol ACGIH TLV (United States, 3/2019).
TWA: 152 mg/m³ 8 hours.
TWA: 50 ppm 8 hours.
ethylbenzene EU OEL (Europe, 2/2017). Absorbed through skin.
STEL: 884 mg/m³ 15 minutes.
STEL: 200 ppm 15 minutes.
TWA: 442 mg/m³ 8 hours.
TWA: 100 ppm 8 hours.
toluene EU OEL (Europe, 2/2017). Absorbed through skin.
STEL: 384 mg/m³ 15 minutes.
STEL: 100 ppm 15 minutes.
TWA: 192 mg/m³ 8 hours.
TWA: 50 ppm 8 hours.
Recommended monitoring : If this product contains ingredients with exposure limits, personal, workplace
procedures atmosphere or biological monitoring may be required to determine the effectiveness
of the ventilation or other control measures and/or the necessity to use respiratory
protective equipment. Reference should be made to monitoring standards, such as
the following: European Standard EN 689 (Workplace atmospheres - Guidance for
the assessment of exposure by inhalation to chemical agents for comparison with
limit values and measurement strategy) European Standard EN 14042 (Workplace
atmospheres - Guide for the application and use of procedures for the assessment of
exposure to chemical and biological agents) European Standard EN 482
English (GB) United Arab Emirates 6/14
Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II
Code : 00239839 Date of issue/Date of revision : 3 February 2020
SIGMA EP 159 SEALER BASE

SECTION 8: Exposure controls/personal protection

(Workplace atmospheres - General requirements for the performance of procedures
for the measurement of chemical agents) Reference to national guidance
documents for methods for the determination of hazardous substances will also be
required.

8.2 Exposure controls

Appropriate engineering : Use only with adequate ventilation. Use process enclosures, local exhaust
controls ventilation or other engineering controls to keep worker exposure to airborne
contaminants below any recommended or statutory limits. The engineering controls
also need to keep gas, vapour or dust concentrations below any lower explosive
limits. Use explosion-proof ventilation equipment.
Individual protection measures
Hygiene measures : Wash hands, forearms and face thoroughly after handling chemical products, before
eating, smoking and using the lavatory and at the end of the working period.
Appropriate techniques should be used to remove potentially contaminated clothing.
Contaminated work clothing should not be allowed out of the workplace. Wash
contaminated clothing before reusing. Ensure that eyewash stations and safety
showers are close to the workstation location.
Eye/face protection : Chemical splash goggles and face shield.
Skin protection
Hand protection : Chemical-resistant, impervious gloves complying with an approved standard should
be worn at all times when handling chemical products if a risk assessment indicates
this is necessary. Considering the parameters specified by the glove manufacturer,
check during use that the gloves are still retaining their protective properties. It
should be noted that the time to breakthrough for any glove material may be
different for different glove manufacturers. In the case of mixtures, consisting of
several substances, the protection time of the gloves cannot be accurately estimated.
When prolonged or frequently repeated contact may occur, a glove with a protection
class of 6 (breakthrough time greater than 480 minutes according to EN 374) is
recommended. When only brief contact is expected, a glove with a protection class
of 2 or higher (breakthrough time greater than 30 minutes according to EN 374) is
recommended. The user must check that the final choice of type of glove selected
for handling this product is the most appropriate and takes into account the particular
conditions of use, as included in the user's risk assessment.
Gloves : butyl rubber
Body protection : Personal protective equipment for the body should be selected based on the task
being performed and the risks involved and should be approved by a specialist
before handling this product. When there is a risk of ignition from static electricity,
wear anti-static protective clothing. For the greatest protection from static discharges,
clothing should include anti-static overalls, boots and gloves. Refer to European
Standard EN 1149 for further information on material and design requirements and
test methods.
Other skin protection Appropriate footwear and any additional skin protection measures should be
selected based on the task being performed and the risks involved and should be
approved by a specialist before handling this product.
Respiratory protection : Respirator selection must be based on known or anticipated exposure levels, the
hazards of the product and the safe working limits of the selected respirator. If
workers are exposed to concentrations above the exposure limit, they must use
appropriate, certified respirators. Use a properly fitted, air-purifying or air-fed
respirator complying with an approved standard if a risk assessment indicates this is
necessary.
Environmental exposure : Emissions from ventilation or work process equipment should be checked to ensure
controls they comply with the requirements of environmental protection legislation. In some
cases, fume scrubbers, filters or engineering modifications to the process equipment
will be necessary to reduce emissions to acceptable levels.

English (GB) United Arab Emirates 7/14

Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II
Code : 00239839 Date of issue/Date of revision : 3 February 2020
SIGMA EP 159 SEALER BASE

SECTION 9: Physical and chemical properties

9.1 Information on basic physical and chemical properties
Appearance
Physical state : Liquid.
Colour : Not available.
Odour : Characteristic.
Odour threshold : Not available.
pH : insoluble in water.
Melting point/freezing point : May start to solidify at the following temperature: -54°C (-65.2°F) This is based on
data for the following ingredient: Hydrocarbons, C10-C13, n-alkanes, isoalkanes,
cyclics, < 2% aromatics . Weighted average: -92.01°C (-133.6°F)
Initial boiling point and boiling : >37.78°C
range
Flash point : Closed cup: 28°C
Evaporation rate : Highest known value: 0.84 (ethylbenzene) Weighted average: 0.7compared with
butyl acetate
Flammability (solid, gas) : liquid
Upper/lower flammability or : Greatest known range: Lower: 1.7% Upper: 10.9% (2-methylpropan-1-ol)
explosive limits
Vapour pressure : Highest known value: <1.6 kPa (<12 mm Hg) (at 20°C) (2-methylpropan-1-ol).
Weighted average: 0.93 kPa (6.98 mm Hg) (at 20°C)
Vapour density : Highest known value: 3.7 (Air = 1) (xylene). Weighted average: 3.55 (Air = 1)
Relative density : 1
Solubility(ies) : Insoluble in the following materials: cold water.
Partition coefficient: n-octanol/ : Not applicable.
water
Auto-ignition temperature : Lowest known value: >230°C (>446°F) (Hydrocarbons, C10-C13, n-alkanes,
isoalkanes, cyclics, < 2% aromatics ).
Decomposition temperature : Stable under recommended storage and handling conditions (see Section 7).
Viscosity : Kinematic (room temperature): >4 cm 2/s
Kinematic (40°C): >0.21 cm 2/s
Viscosity : 60 - 100 s (ISO 6mm)
Explosive properties : Product does not present an explosion hazard.
Oxidising properties : Product does not present an oxidizing hazard.

9.2 Other information

No additional information.

SECTION 10: Stability and reactivity

10.1 Reactivity : No specific test data related to reactivity available for this product or its ingredients.

10.2 Chemical stability : The product is stable.

10.3 Possibility of : Under normal conditions of storage and use, hazardous reactions will not occur.
hazardous reactions

10.4 Conditions to avoid : When exposed to high temperatures may produce hazardous decomposition
products.
Refer to protective measures listed in sections 7 and 8.

English (GB) United Arab Emirates 8/14

Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II
Code : 00239839 Date of issue/Date of revision : 3 February 2020
SIGMA EP 159 SEALER BASE

SECTION 10: Stability and reactivity

10.5 Incompatible materials : Keep away from the following materials to prevent strong exothermic reactions:
oxidising agents, strong alkalis, strong acids.

10.6 Hazardous : Depending on conditions, decomposition products may include the following
decomposition products materials: carbon oxides metal oxide/oxides

SECTION 11: Toxicological information

11.1 Information on toxicological effects
Acute toxicity
Product/ingredient name Result Species Dose Exposure
xylene LD50 Dermal Rabbit >1.7 g/kg -
LD50 Oral Rat 4.3 g/kg -
Epoxy Resin (700<MW<=1100) LD50 Dermal Rat >2000 mg/kg -
LD50 Oral Rat >2000 mg/kg -
2-methylpropan-1-ol LC50 Inhalation Vapour Rat 24.6 mg/l 4 hours
LD50 Dermal Rabbit 2460 mg/kg -
LD50 Oral Rat 2830 mg/kg -
ethylbenzene LC50 Inhalation Vapour Rat 17.8 mg/l 4 hours
LD50 Dermal Rabbit 17.8 g/kg -
LD50 Oral Rat 3.5 g/kg -
Hydrocarbons, C10-C13, n-alkanes, LD50 Dermal Rabbit >5000 mg/kg -
isoalkanes, cyclics, < 2% aromatics
LD50 Oral Rat >6 g/kg -
toluene LC50 Inhalation Vapour Rat 49 g/m³ 4 hours
LD50 Dermal Rabbit 8.39 g/kg -
LD50 Oral Rat 5580 mg/kg -
Conclusion/Summary : There are no data available on the mixture itself.
Acute toxicity estimates
Route ATE value
Dermal 2916.39 mg/kg
Inhalation (vapours) 26.28 mg/l
Irritation/Corrosion
Product/ingredient name Result Species Score Exposure Observation
xylene Skin - Moderate irritant Rabbit - 24 hours 500 mg -

Conclusion/Summary
Skin : There are no data available on the mixture itself.
Eyes : There are no data available on the mixture itself.
Respiratory : There are no data available on the mixture itself.
Sensitisation
Conclusion/Summary
Skin : There are no data available on the mixture itself.
Respiratory : There are no data available on the mixture itself.
Mutagenicity
Conclusion/Summary : There are no data available on the mixture itself.
Carcinogenicity
Conclusion/Summary : There are no data available on the mixture itself.
Reproductive toxicity
Conclusion/Summary : There are no data available on the mixture itself.
Teratogenicity
English (GB) United Arab Emirates 9/14
Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II
Code : 00239839 Date of issue/Date of revision : 3 February 2020
SIGMA EP 159 SEALER BASE

SECTION 11: Toxicological information

Conclusion/Summary : There are no data available on the mixture itself.
Specific target organ toxicity (single exposure)
Product/ingredient name Category Route of Target organs
exposure
xylene Category 3 Not applicable. Respiratory tract irritation
2-methylpropan-1-ol Category 3 Not applicable. Narcotic effects
Category 3 Not applicable. Respiratory tract irritation
toluene Category 3 Not applicable. Narcotic effects
Specific target organ toxicity (repeated exposure)
Product/ingredient name Category Route of Target organs
exposure
ethylbenzene Category 2 Not determined hearing organs
toluene Category 2 Not determined Not determined
Aspiration hazard
Product/ingredient name Result
xylene ASPIRATION HAZARD - Category 1
ethylbenzene ASPIRATION HAZARD - Category 1
Hydrocarbons, C10-C13, n-alkanes, isoalkanes, cyclics, < 2% ASPIRATION HAZARD - Category 1
aromatics
toluene ASPIRATION HAZARD - Category 1
Information on likely : Not available.
routes of exposure
Potential acute health effects
Inhalation : May cause respiratory irritation.
Ingestion : No known significant effects or critical hazards.
Skin contact : Causes skin irritation. Defatting to the skin. May cause an allergic skin reaction.
Eye contact : Causes serious eye damage.
Symptoms related to the physical, chemical and toxicological characteristics
Inhalation : Adverse symptoms may include the following:
respiratory tract irritation
coughing
Ingestion : Adverse symptoms may include the following:
stomach pains
Skin contact : Adverse symptoms may include the following:
pain or irritation
redness
dryness
cracking
blistering may occur
Eye contact : Adverse symptoms may include the following:
pain
watering
redness
Delayed and immediate effects as well as chronic effects from short and long-term exposure
Short term exposure
Potential immediate : Not available.
effects
Potential delayed effects : Not available.
Long term exposure

English (GB) United Arab Emirates 10/14

Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II
Code : 00239839 Date of issue/Date of revision : 3 February 2020
SIGMA EP 159 SEALER BASE

SECTION 11: Toxicological information

Potential immediate : Not available.
effects
Potential delayed effects : Not available.
Potential chronic health effects
Not available.

Conclusion/Summary : Not available.

General : Prolonged or repeated contact can defat the skin and lead to irritation, cracking and/
or dermatitis. Once sensitized, a severe allergic reaction may occur when
subsequently exposed to very low levels.
Carcinogenicity : No known significant effects or critical hazards.
Mutagenicity : No known significant effects or critical hazards.
Teratogenicity : No known significant effects or critical hazards.
Developmental effects : No known significant effects or critical hazards.
Fertility effects : No known significant effects or critical hazards.
Other information : Not available.
There are no data available on the mixture itself. The mixture has been assessed following the conventional method of
the CLP Regulation (EC) No 1272/2008 and is classified for toxicological properties accordingly. See Sections 2 and 3
for details.

Exposure to component solvent vapour concentrations in excess of the stated occupational exposure limit may result in
adverse health effects such as mucous membrane and respiratory system irritation and adverse effects on the kidneys,
liver and central nervous system. Symptoms and signs include headache, dizziness, fatigue, muscular weakness,
drowsiness and, in extreme cases, loss of consciousness.
Solvents may cause some of the above effects by absorption through the skin. Repeated or prolonged contact with the
mixture may cause removal of natural fat from the skin, resulting in non-allergic contact dermatitis and absorption
through the skin.
If splashed in the eyes, the liquid may cause irritation and reversible damage.
Ingestion may cause nausea, diarrhea and vomiting.
This takes into account, where known, delayed and immediate effects and also chronic effects of components from
short-term and long-term exposure by oral, inhalation and dermal routes of exposure and eye contact.

Contains Epoxy Resin (700<MW<=1100). May produce an allergic reaction.

SECTION 12: Ecological information

12.1 Toxicity
Product/ingredient name Result Species Exposure
2-methylpropan-1-ol Acute EC50 1100 mg/l Daphnia 48 hours
ethylbenzene Acute LC50 150 to 200 mg/l Fish 96 hours
Fresh water
Conclusion/Summary : There are no data available on the mixture itself.

12.2 Persistence and degradability

Conclusion/Summary : There are no data available on the mixture itself.
Product/ingredient name Aquatic half-life Photolysis Biodegradability
xylene - - Readily
ethylbenzene - - Readily
toluene - - Readily

12.3 Bioaccumulative potential

English (GB) United Arab Emirates 11/14

Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II
Code : 00239839 Date of issue/Date of revision : 3 February 2020
SIGMA EP 159 SEALER BASE

SECTION 12: Ecological information

Product/ingredient name LogPow BCF Potential
xylene 3.16 7.4 to 18.5 low
2-methylpropan-1-ol 0.76 - low
ethylbenzene 3.15 79.43 low
toluene 2.73 8.32 low

12.4 Mobility in soil

Soil/water partition : Not available.
coefficient (KOC)
Mobility : Not available.

12.5 Results of PBT and vPvB assessment

This mixture does not contain any substances that are assessed to be a PBT or a vPvB.

12.6 Other adverse effects : No known significant effects or critical hazards.

SECTION 13: Disposal considerations

The information in this section contains generic advice and guidance. The list of Identified Uses in Section 1 should be
consulted for any available use-specific information provided in the Exposure Scenario(s).
13.1 Waste treatment methods
Product
Methods of disposal : The generation of waste should be avoided or minimised wherever possible.
Disposal of this product, solutions and any by-products should at all times comply
with the requirements of environmental protection and waste disposal legislation and
any regional local authority requirements. Dispose of surplus and non-recyclable
products via a licensed waste disposal contractor. Waste should not be disposed of
untreated to the sewer unless fully compliant with the requirements of all authorities
with jurisdiction.
Hazardous waste : Yes.
European waste catalogue (EWC)
Waste code Waste designation
08 01 11* waste paint and varnish containing organic solvents or other hazardous substances

Packaging
Methods of disposal : The generation of waste should be avoided or minimised wherever possible. Waste
packaging should be recycled. Incineration or landfill should only be considered
when recycling is not feasible.
Type of packaging European waste catalogue (EWC)
Container 15 01 06 mixed packaging

Special precautions : This material and its container must be disposed of in a safe way. Care should be
taken when handling emptied containers that have not been cleaned or rinsed out.
Empty containers or liners may retain some product residues. Vapour from product
residues may create a highly flammable or explosive atmosphere inside the
container. Do not cut, weld or grind used containers unless they have been cleaned
thoroughly internally. Avoid dispersal of spilt material and runoff and contact with
soil, waterways, drains and sewers.

English (GB) United Arab Emirates 12/14

Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II
Code : 00239839 Date of issue/Date of revision : 3 February 2020
SIGMA EP 159 SEALER BASE

SECTION 14: Transport information

ADR/RID IMDG IATA
14.1 UN number UN1263 UN1263 UN1263
14.2 UN proper PAINT PAINT PAINT
shipping name
14.3 Transport 3 3 3
hazard class(es)
14.4 Packing group III III III
14.5 No. No. No.
Environmental
hazards
Marine pollutant Not applicable. Not applicable. Not applicable.
substances

Additional information
ADR/RID : This class 3 viscous liquid is not subject to regulation in packagings up to 450 L according to
2.2.3.1.5.1.
Tunnel code : (D/E)
IMDG : This class 3 viscous liquid is not subject to regulation in packagings up to 450 L according to
2.3.2.5.
IATA : None identified.

14.6 Special precautions for : Transport within user’s premises: always transport in closed containers that are
user upright and secure. Ensure that persons transporting the product know what to do in
the event of an accident or spillage.

14.7 Transport in bulk : Not applicable.

according to Annex II of
Marpol and the IBC Code

SECTION 15: Regulatory information

15.1 Safety, health and environmental regulations/legislation specific for the substance or mixture
EU Regulation (EC) No. 1907/2006 (REACH)
Annex XIV - List of substances subject to authorisation
Annex XIV
None of the components are listed.
Substances of very high concern
None of the components are listed.
Annex XVII - Restrictions : Not applicable.
on the manufacture,
placing on the market and
use of certain dangerous
substances, mixtures and
articles
Other national and international regulations.
Ozone depleting substances (1005/2009/EU)
Not listed.

15.2 Chemical safety : No Chemical Safety Assessment has been carried out.
assessment

English (GB) United Arab Emirates 13/14

Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II
Code : 00239839 Date of issue/Date of revision : 3 February 2020
SIGMA EP 159 SEALER BASE

SECTION 16: Other information

Indicates information that has changed from previously issued version.
Abbreviations and acronyms : ATE = Acute Toxicity Estimate
CLP = Classification, Labelling and Packaging Regulation [Regulation (EC) No.
1272/2008]
DNEL = Derived No Effect Level
EUH statement = CLP-specific Hazard statement
PNEC = Predicted No Effect Concentration
RRN = REACH Registration Number
Full text of abbreviated H : H225 Highly flammable liquid and vapour.
statements H226 Flammable liquid and vapour.
H304 May be fatal if swallowed and enters airways.
H312 Harmful in contact with skin.
H315 Causes skin irritation.
H317 May cause an allergic skin reaction.
H318 Causes serious eye damage.
H319 Causes serious eye irritation.
H332 Harmful if inhaled.
H335 May cause respiratory irritation.
H336 May cause drowsiness or dizziness.
H361d Suspected of damaging the unborn child.
H373 May cause damage to organs through prolonged or repeated exposure.
Full text of classifications : Acute Tox. 4, H312 ACUTE TOXICITY (dermal) - Category 4
[CLP/GHS] Acute Tox. 4, H332 ACUTE TOXICITY (inhalation) - Category 4
Asp. Tox. 1, H304 ASPIRATION HAZARD - Category 1
EUH066 Repeated exposure may cause skin dryness or cracking.
Eye Dam. 1, H318 SERIOUS EYE DAMAGE/EYE IRRITATION - Category 1
Eye Irrit. 2, H319 SERIOUS EYE DAMAGE/EYE IRRITATION - Category 2
Flam. Liq. 2, H225 FLAMMABLE LIQUIDS - Category 2
Flam. Liq. 3, H226 FLAMMABLE LIQUIDS - Category 3
Repr. 2, H361d REPRODUCTIVE TOXICITY (Unborn child) - Category 2
Skin Irrit. 2, H315 SKIN CORROSION/IRRITATION - Category 2
Skin Sens. 1, H317 SKIN SENSITISATION - Category 1
STOT RE 2, H373 SPECIFIC TARGET ORGAN TOXICITY - REPEATED
EXPOSURE - Category 2
STOT SE 3, H335 SPECIFIC TARGET ORGAN TOXICITY - SINGLE
EXPOSURE (Respiratory tract irritation) - Category 3
STOT SE 3, H336 SPECIFIC TARGET ORGAN TOXICITY - SINGLE
EXPOSURE (Narcotic effects) - Category 3
History
Date of issue/ Date of : 3 February 2020
revision
Date of previous issue : 3 November 2019
Prepared by : EHS
Version : 1.03
Disclaimer
The information contained in this data sheet is based on present scientific and technical knowledge. The purpose of this
information is to draw attention to the health and safety aspects concerning the products supplied by us, and to
recommend precautionary measures for the storage and handling of the products. No warranty or guarantee is given in
respect of the properties of the products. No liability can be accepted for any failure to observe the precautionary
measures described in this data sheet or for any misuse of the products.

English (GB) United Arab Emirates 14/14