Scribd
Upload
19 views

QRT configurition

QRT configure

Uploaded by

shahzadasadat8
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
19 views

QRT configurition

QRT configure

Uploaded by

shahzadasadat8
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
You are on page 1/ 3

To configure a **MikroTik QRT device** using **Winbox** (a MikroTik configuration

tool), follow these steps:

---

### **Prerequisites:**
- **MikroTik QRT device** installed and powered on.
- A **computer** connected to the QRT device via Ethernet.
- **Winbox** installed on your computer (download it from MikroTik's official
website).

---

### **Step-by-Step Configuration Guide for MikroTik QRT in Winbox:**

#### **Step 1: Connect to the QRT Device**


1. Open **Winbox** on your computer.
2. Connect your computer to the QRT device via Ethernet cable.
3. In Winbox, you will see your QRT device listed under **"Neighbors"** if it's
properly connected and powered on.
4. Click on the **MAC address** of the QRT device under the **Neighbors** tab and
click **Connect**.
- Username: **admin** (default)
- Password: **(leave blank)** by default.

---

#### **Step 2: Basic Configuration**


Once connected, you'll be in the **RouterOS interface** of the QRT device.

1. **Change Default Admin Password**:


- In the **System** menu, go to **Users**.
- Select **admin**, then click **Edit**.
- Set a new password to secure your device.

2. **Set IP Address**:
- Go to **IP** > **Addresses**.
- Click the **+** to add a new IP address.
- Set an IP address for your QRT device (e.g., `192.168.88.1/24`) on the
Ethernet interface.
- Apply and save the configuration.

---

#### **Step 3: Configure Wireless Settings**


1. Go to **Wireless** > **Interface**.
2. Select the wireless interface (e.g., **wlan1**).
3. Set the following parameters:
- **Mode**: Choose **AP Bridge** or **Station** depending on whether you want to
set the QRT as an access point or as a client.
- **Frequency**: Select the channel or frequency band (5 GHz for QRT devices,
typically).
- **SSID**: Set a name for your wireless network (if using **AP Bridge** mode).
- **Wireless Protocol**: Choose **802.11a** (for 5 GHz devices).
- **Security Profiles**: You can configure WPA2 security for your wireless
network.

4. For **Station Mode** (if connecting to another AP):


- Set the **Mode** to **Station**.
- Click **Scan** to find available networks and select the desired one.
- Enter the **WPA/WPA2 key** if required to connect to the remote AP.

---

#### **Step 4: Set up IP Routing (Optional)**


1. If you want to route traffic through the QRT device, configure IP routing:
- Go to **IP** > **Routes**.
- Add the default route pointing to the gateway (if necessary).

---

#### **Step 5: Configure NAT and Firewall (If Using for Internet Access)**
1. If you're using the QRT for internet access, you need to configure **NAT**
(Network Address Translation):
- Go to **IP** > **Firewall**.
- Under the **NAT** tab, click **+** to add a new rule.
- Set **Chain** to **srcnat**, and in **Out. Interface**, select the Ethernet or
wireless interface connected to the internet.
- Set **Action** to **masquerade** to allow the QRT device to share the internet
connection.

---

#### **Step 6: Monitor and Test the Connection**


1. Go to **Wireless** > **Registration** to check which devices are connected if
using **AP Bridge** mode.
2. Go to **Tools** > **Ping** to test the connection between the QRT device and
other devices in your network or the internet.
3. If using **Station Mode**, ensure the QRT device is successfully connected to
the remote access point and has internet access (if desired).

---

### **Step 7: Save Configuration**


After completing the configuration, save your changes:
- Go to **System** > **Reboot** to reboot the device if needed.

---

### **Optional: Update Firmware**


It's always a good practice to check for new RouterOS versions and update the
firmware:
1. Go to **System** > **Packages** > **Check for Updates**.
2. Download the latest version if available and upgrade the device firmware.

---

### **Troubleshooting Tips:**


- If you cannot connect to the QRT device, ensure it's powered and properly
connected to your network.
- If wireless connection issues arise, check the frequency settings and SSID
configurations.
- Verify that firewall and NAT rules are set correctly if the device is acting as a
gateway or router.

---

This should help you get started with configuring your MikroTik QRT device using
Winbox. Let me know if you need more detailed instructions on any specific
configuration!

You might also like