Scribd
Upload
14 views7 pages

PTS-Task-4-Written-test-Performance-test-performance-criteria-Demonstration-with-questioning-checklist (1)

Uploaded by

neckyjulia94
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
14 views7 pages

PTS-Task-4-Written-test-Performance-test-performance-criteria-Demonstration-with-questioning-checklist (1)

Uploaded by

neckyjulia94
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 7

School heading

WRITTEN TEST

Identifications:
Direction: Identify the of what is being asked: write your answer
on the space provided for:

1. _____________ is a device used to emit a stream of hot air, usually at


temperatures100 °C and 550 °C used to bend PVC pipe
2. _____________is a type of tool used by plumbers/electrician to cut
metal pipe
3. ____________a holding device attached to a workbench; has two jaws
to hold work piece firmly in place.
4. ____________ is a bender normally used for RSC, RMC, and IMC
conduits.
5. ______________is an adjustable wrench used for turning soft iron
pipes and fittings with a rounded surface.
6. A ______________________ is an electromechanical data storage device
that uses magnetic storage to store and retrieve digital
information using one or more rigid rapidly rotating disks
(platters) coated with magnetic material.
7. _________________ is a TV system in which signals are not publicly
distributed but are monitored, primarily for surveillance
and security purposes.
8. _____________ cable consists of a solid or stranded center conductor
(wire) surrounded by a heavy layer of dielectric
(insulation).
9. _________ cable is available which combines an RG-59 coax cable w/
2 18 gauge twisted pair conductors in the same
jacket.
10.The primary function of a ______________ is to convert electric current from a
source to the correct voltage, current, and frequency to power the load.
School heading

ANSWER KEY TO WRITTEN TEST

1. heat gun
2. pipe cutter
3. Bench vise
4. Hickey
5. pipe wrench
6. Hard disk drive
7. CCTV (closed-circuit television)
8. Coax
9. Siamese
10.power supply
School heading

PERFORMANCE
TEST

SPECIFIC INSTRUCTION FOR THE


CANDIDATE
QUALIFICATION Electrical Installation and Maintenance
NC II
Title of PBAs : “How to Use the hydraulic pipe bender”
Unit of Perform roughing-in activities, wiring
Competency and cabling works for single phase
Covered distribution, power, lighting and
auxiliary systems”
PLEASE READ CAREFULLY:
Given the necessary tools, materials and equipment, you are required to
assemble computer hardware in accordance with the accepted
institutional/industry standard. (Allotted time: 1hour)
1. Prepare the workplace.
2. Gather tools, materials and equipment needed.
3. Perform anti-static discharge.
4. Assemble computer hardware.
5. Connect the computer peripherals.
6. Power on the computer.
7. Observe safety precautions while working.
8. Apply 5S before, during, and after performing the task.

Steps/Procedure:
1.Connect your hydraulic pipe bender to your hydraulic pump. This is done
by taking the end of the hose and pulling back the speed ring on
the brass fastener's end.
2.Hold the ring back,
3.Slide the fastener over the hydraulic pipe bender's nozzle and let the
speed ring slide back in place.
4.Pull carefully the hose to find out that it is locked in place.
5.Set the pin on the tube bender for the pipe that you need to bend as per
its size. This will hold the pipe in place. It also gives a pivot point
for the tube as it is being bent.
6.Use a measuring tape to measure the length of the pipe where you need
the bend to be.
7.Slide the pipe on the hydraulic pipe bender. Using locking arm, lock the
pipe into position so that the pipe does not slide while the bending
is done.
School heading

8.Switch on the hydraulic pump and then activate the hydraulic tube
bender. Keep your hands away while the bender is operating.
9.Close the bender when the bend process is completed. Now you can
unlock the locking mechanism.
10. The above steps need to be repeated for each bend and when you
have completed the work, shut off the hydraulic pump and the bender. The
hydraulic hose is then carefully disconnected from the bender. This is done
by pulling back on the speed ring and pulling bender's hose. Remember that
the hose is now under pressure, so you have to be very careful when
removing it from the bender.

EQUIPMENT
QUANTITY DESCRIPTIO
N
1 piece Hydraulic pipe bender
1 piece Vise/vice
1 piece Bench vice
1 piece Chain pipe vice
1 piece Vise/vice

1 piece Pipe wrench


1 piece Portable electric threader machine
1 piece Heat gun
TOOLS
QUANTITY DESCRIPTION
1 piece hydraulic pipe bender
1 piece hydraulic pump
1 piece Pie cutter
1 piece Hack saw
1 piece Pvc pipe cutter
1 piece Electrical pipe bender
1 piece Pipe wrench
School heading

ASSESSMENT METHOD: Use performance criteria checklist

PERFORMANCE
CRITERIA
CHECKLIST

SPECIFIC INSTRUCTION FOR THE CANDIDATE YES NO

1. Selected the correct PPE?

2. Connected correctly the hose correctly?

3. Checked the hydraulic fluid?

4. Set the pin on the tube bender?

5. Disconnected the hose?

6. Cleaned the hydraulic pipe bender?


School heading

DEMONSTRATION WITH
QUESTIONING
CHECKLIST
Trainee Name:

Trainer Name:
Qualification: Electrical Installation and Maintenance
NC II
Unit of Competency: Perform roughing-in activities, wiring and
cabling works for single phase
distribution, power, lighting and auxiliary
systems
Date of Assessment:
Time of Assessment:
Instructions for Demonstration
Given the necessary tools, the candidate will be able to demonstrate
Performing roughing-in activities, wiring and cabling works for
single phase distribution, power, lighting and auxiliary systems
following standard procedures within 1hr.
Check to show
DEMONSTRATION if evidence is
demonstrated
During the demonstration of skills, did Yes No N/A
the candidate:
1. Identify the correct quantities of conduit, fittings
and accessories as per job requirements
2. Selected tools, equipment’s, and personal protective
equipment as per job requirement
3. Installed electrical metallic /non- metallic (PVC
conduit)
4. Installed wire ways and cable tray
School heading

5. Installed auxiliary terminal cabinet and distribution


panel
6. Prepared for cable pulling and installation
7. Performed wiring and cabling lay out
8. Safety procedures are followed in line with
standard operating procedures (SOPs)

The candidate’s demonstration was:

Satisfactory Not Satisfactory

You might also like