Version 01_09_18

Belimo Energy Valve™

Technical Documentation

> Learn more

www.energyvalve.com

Cloud Delta T Energy

Optimization Management Monitoring
Table of Contents
Component Identification
Small Valve (½” to 2”) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Large Valve (2½” to 6”) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Flow Characteristics and Tolerances . . . . . . . . . . . . . . . . . . . . . . . . 4
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Nomenclature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Set Up Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Product Range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Control Mode Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Installation
Piping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Remote Sensor Installation . . . . . . . . . . . . . . . . . . . . . . . . . 12
Actuator, Temperature, and Flow Sensor Replacement. . . . . . . . . . . . 13
Orientation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Insulation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Flange Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Wiring Diagrams. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Control Mode Sequence of Operation
Flow Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Power Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Position Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Delta T Manager Options. . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Web View
Connecting Energy Valve to Ethernet. . . . . . . . . . . . . . . . . . . . . 18
Compatible Browsers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Login. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Web View User Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Date and Time Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
IP Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Version Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Data Logging. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
User Administration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
BACnet MP-Slave and Modus Settings. . . . . . . . . . . . . . . . . . . . 24
BACnet IP Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
BACnet MS/TP Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Modbus TCP Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Modbus RTU Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Cloud Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Cloud Connectivity Quick Start Guide . . . . . . . . . . . . . . . . . . . . 28
Cloud Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

2
 Table of Contents Continued
Field Programming and Commissioning Options. . . . . . . . . . . . . . . . . 33
Web View Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
ZTH US . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Actuator Adaptation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Belimo Data Analysis Tool. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Downloading Coil Data from Web View . . . . . . . . . . . . . . . . . . . 39
Dashboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Delta T Determination. . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Actuator and Valve Specifications
Valve Specifications (½” to 2”). . . . . . . . . . . . . . . . . . . . . . . . 41
ANSI 125 Valve Specifications (2½” to 6”). . . . . . . . . . . . . . . . . . 42
ANSI 250 Valve Specifications (2½” to 6”). . . . . . . . . . . . . . . . . . 43
Actuator Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Flow Pressure Characteristics
Flow Reduction Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Input Signal Scaling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
BACnet Protocol (PICS Statement) . . . . . . . . . . . . . . . . . . . . . . . . 47
BACnet Object Description List . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Modbus Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Modbus Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Modbus Registers/Address. . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

3
Energy Valve
Component Identification

Overview
Ultrasonic flow meter with temperature and glycol compensation
is wet calibrated to obtain published accuracy specifications. The
Belimo Energy Valve is now an IoT device with a suite of cloud based
services which can benchmark coil performance, analyze glycol 1 3
concentration, store energy data, send alerts and commission for
optimal performance.
The Energy Valve is a pressure independent valve that measures
and manages coil energy by using an embedded ultrasonic flow 2 5
meter, along with supply and return water temperature sensors.
The Energy Valve also has the patented Power Control and Belimo
Delta T Manager™ logics built-in that monitors coil performance and
optimizes the available energy of the coil by maintaining the Delta
T. In addition to the standard analog signal and feedback wiring, it
communicates its data to the Building Management System (BMS)
4
via BACnet MS/TP or BACnet IP as well as Modbus RTU and Modbus
TCP/IP. The built-in web server collects up to 13 months of data that
can be downloaded to external tools for further optimization.

3 Large Valve (2 ½” – 6”)

1 • 1 Non-spring return or electronic fail-safe actuator with analog
input and output
• 2 2-way characterized control valve with tight close-off 0% leakage
4 4
2 (not available on -250 models)
• 3 Flow sensor: Magnetic
• 4 Supply temperature sensor: with thermowell
• 5 Return temperature sensor: embedded

Small Valve (½” - 2”)

• 1 Non-spring return or electronic fail-safe actuator with analog
input and output
• 2 2-way characterized control valve with tight close-off 0%

Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

leakage
• 3 Ultrasonic flow meter with temperature and glycol compensation
is wet calibrated to obtain published accuracy specifications
• 4 Supply and return temperature sensors with thermowells and
pipe fittings

Curve 1:40

Flow Characteristics and Tolerances

Flow Measurement Tolerance +2% of the actual Flow.
Flow Control Tolerance of the EV: +5% of the actual Flow.
V’nom = flow rating of valve as listed in catalog
The EV has an equal percentage flow curve.
The equal percentage curve offers a more stable control
for heating and cooling applications.

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

4
 Energy Valve
Features

The Energy Valve is an energy metering pressure independent characterized

control valve that optimizes, documents and proves water coil performance.
Features
IoT Capability - Advanced System Optimization through cloud technology.
BELIMO
Pressure ENERGY
Glycol Monitoring - A feature exclusive to the Energy valve that provides the ability Flow VALVE

to determine glycol content. By utilizing advanced algorithms in the Belimo designed

ultrasonic flow meter the glycol concentration can be provided. A minimum flow rate is
provided automatically if glycol content is too low which will prevent system freezing and
damage.

Flow Control / Pressure Independent - Accurate and automatic pressure independent flow control is achieved through the Energy Valve’s electromagnetic or
ultrasonic flow sensor. The valve reacts to changes in pressure and modulates the actuator to maintain the flow setpoint.

Power Control - Allows you to set your heat transfer thermal power output to a maximum full load value with a linear heat transfer response throughout the entire
load range. Coil and valve characteristics become irrelevant making the valve pressure and temperature independent.

True Flow - Unlike mechanical pressure independent valves that provide an approximated/calculated flow, the built-in electronic flow meter provides True Flow as
feedback. Flow verification is simple, troubleshooting is fast, and True Flow can be shared with the DDC system.

Dynamic Balancing - Coil is always perfectly balanced without the need for any time consuming balancing effort regardless of hydronic pressure variations or
piping changes. Occupant comfort is improved by eliminating hunting and cycling of the valve that eliminates overflows and increases equipment longevity.

Energy Meter - Thermal heat transfer energy data is transparent allowing users the ability to see and document system performance during commissioning and
over time. Energy waste is identified and eliminated by modifying settings within the Energy Valve logic and by sharing the data with an Energy Management
Control System.

Belimo Delta T Manager™ - Continuously monitors the coil ∆T and compares this value with the dT setpoint. If the actual ∆T is below the dT setpoint, the logic
will reduce valve flow to bring ∆T back to the setpoint.

Live Data - Data such as delta T, flow, valve position, and heat transfer thermal power can be viewed live or shared with the DDC system. Commissioning,
troubleshooting, and integration to DDC systems is fast and reliable.

Coil History - Live data as well as many other performance parameters are stored for up to 13 months in the actuator. Belimo provides an Excel based Data
Analysis Tool that is free to download. This data allows operators to benchmark and better understand system performance.
Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

Characterized Control Valve (CCV) Technology* - High rangeability delivers superior light load flow control, eliminates “opening jump”, and on-off control
response at low flow. The ball valve is self-cleaning which eliminates debris buildup and clogging.

Zero Leakage / High Close-off* - Wasteful “ghost energy” flow losses are eliminated which saves energy cost and improves occupant comfort.

Low Minimum Pressure Drop - Valve flow output is pressure independent with as low as 1 psid operating differential pressure. Designers can now size valves and
pumps to operate at 3 - 4 psid that reduces pump head and allows for smaller pump selection.

Field Configuration - Small hand held tool or web browser users now can make field adjustments. Additional system integration and control with Modbus RTU
and TCP/IP proving users with a wide range of options for integration including, BTL listed BACnet MSTP and BACnet IP, Analog and Belimo MP bus, BACnet MS/
TP or IP.

Commissioning Report - Provides a report of the valve settings for historical records and operation allowing for a confirmation of valve operation and set up. Save
and reload setting: easily save settings from one valve configuration and load in another allowing for fast and accurate integration.

5-Year Warranty - Without cloud integration.

7-Year Warranty - With connection to cloud.**

*Not available on -250 models.

**The following provision supplements the applicable Terms and Conditions of Sale for the Energy Valve 3.0. The 5-year warranty foreseen in the Terms and
Conditions of Sale shall be replaced by a 7-year warranty, provided the following conditions are fulfilled:
• The Cloud-connection on the respective BELIMO device is activated
• The respective BELIMO device has been allocated to a Cloud-Account
• At the time of the warranty claim the connection ratio between the BELIMO device and the BELIMO-Cloud is at least 90% (the connection ratio is
determined by the amount of hours of Cloud-connection of the BELIMO device divided by its operating hours).

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

5
 Energy Valve Nomenclature

EV 250S -127 +ARB 24 -EV

Energy Valve Size Flow Rate Pressure Actuator Type Power

Valve 050 = ½” 1.65 - 713 GPM Rating Non-Spring Return Supply EV = ½” to 6” -L = 2½”
NPT 2-way 075 = ¾” Refer to valve Blank = ANSI 125 LRB, LRX 24 = 24 VAC/DC to 3”*
(½” to 2”) pages for a -250 = ANSI 250 NRB, NRX -B = 4”
100 = 1”
Flanged 2-way full list ARB, ARX to 6”*
125 = 1¼” GRB, GRX
(2½” to 6”) -G = Glycol
150 = 1½” EVX* Measurement
200 = 2” Electronic Fail-Safe
250 = 2½” AKRB, AKRX
300 = 3” GKRB, GKRX
400 = 4” AVKX*
500 = 5”
600 = 6” “X” models are customizable.
Refer to page 6-3 for programming options.
S = Stainless
Steel Ball and
Stem

*ANSI 250 models only

Energy Valve Set Up Options- Default Ordering Example

The Energy Valve can be ordered two different ways once the valve and actuator are selected in the
valve section starting on page 6-10.
1. Default. The product is shipped already programmed with the default settings below. The default

Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

models use actuators that contain a B in the actuator part number i.e. EV250S-127+ARB24-EV.
2. Programmed. The product will ship to the specific settings ordered by the customer using the
Program Codes in steps 1 through 7 on the next page. The programmed models use actuators that
contain an X in the actuator part number i.e. EV250S-127+ARX24-EV.
NOTE: If no specific settings are selected, the product will ship with the default settings below.

DEFAULT SETTINGS
Installation Control and
Maximum Flow Delta T Manager Delta T Setpoint Actuator Setup
Position Feedback Signal
Maximum flow of Return Off 10°F [5.6°C] Non-Spring Return- Control Signal (Y)
the valve Normally Closed (NC) DC 2 to 10V
Electronic Fail-Safe- Feedback Signal (U)
Normally Closed (NC) / DC 2 to 10V
Fail Closed (FC)

COMPLETE DEFAULT ORDERING EXAMPLE:

EV250S-127+ARB24-EV

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

6
 Energy Valve Set Up Options
Programmed Ordering Example

Follow steps 1 through 7.

1. SELECT CODE FOR MAXIMUM FLOW
The maximum GPM can be factory set to the values below. Select the flow code for the desired GPM of the corresponding valve size.

2” 2”
Flow Code ½” GPM ¾” GPM 1” GPM 1¼” GPM 1½” GPM 2½” GPM 3” GPM 4” GPM 5” GPM 6” GPM
(76.1 GPM) (100 GPM)
30 1.65 3.1 5.5 8.6 11.9 22.8 30 38 54 95 149 214
37 2 3.8 6.7 10.5 14.7 28.2 37 47 67 117 183 264
45 2.5 4.6 8.2 12.8 17.8 34.2 45 57 81 143 223 321
55 3 5.7 10 15.7 21.8 41.9 55 70 99 174 272 392
63 3.5 6.5 11.5 18 24.9 47.9 63 80 113 200 312 449
65 3.6 6.7 11.8 18.5 25.7 49.5 65 83 117 206 322 463
68 3.7 7 12.4 19.4 26.9 51.7 68 86 122 216 337 485
71 3.9 7.3 12.9 20.2 28.1 54 71 90 128 225 351 506
72 4 7.4 13.1 20.5 28.5 54.8 72 91 130 228 356 513
75 4.1 7.7 13.7 21.4 29.7 57.1 75 95 135 238 371 535
76 4.2 7.8 13.8 21.7 30.1 57.8 76 97 137 241 376 542
78 4.3 8 14.2 22.2 30.9 59.4 78 99 140 247 386 556
80 4.4 8.2 14.6 22.8 31.7 60.9 80 102 144 254 396 570
82 4.5 8.4 14.9 23.4 32.5 62.4 82 104 148 260 406 585
83 4.6 8.5 15.1 23.7 32.9 63.2 83 105 149 263 411 592
85 4.7 8.8 15.5 24.2 33.7 64.7 85 108 153 269 421 606
87 4.8 9 15.8 24.8 34.5 66.2 87 110 157 276 431 620
89 4.9 9.2 16.2 25.4 35.2 67.7 89 113 160 282 441 635
91 5 9.4 16.6 25.9 36 69.3 91 116 164 288 450 649
93 5.1 9.6 16.9 26.5 36.8 70.8 93 118 167 295 460 663
95 5.2 9.8 17.3 27.1 37.6 72.3 95 121 171 301 470 677
97 5.3 10 17.7 27.6 38.4 73.8 97 123 175 307 480 692
00 5.5 10.3 18.2 28.5 39.6 76.1 100 127 180 317 495 713

2. SELECT CODE FOR INSTALLATION POSITION 3. SELECT CODE FOR DELTA T MANAGER STATUS
Where the Energy Valve is installed in a system either on the supply or return. The Delta T Manager provides a fixed delta T setpoint.
Delta T Scaling varies the setpoint.
Code Description
Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

Code Description
A Supply
0 OFF
Z Return
1 ON Delta T Manager
2 ON Delta T Scaling

4. SELECT CODE FOR DELTA T SETPOINT

This is the Delta T limit of the coil

Code Description Code Description Code Description Code Description Code Description Code Description Code Description
02 02°F / 1.1°C 17 17°F / 9.4°C 32 32°F / 17.8°C 47 47°F / 26.1°C 62 62°F/ 34.4°C 77 77°F/ 42.7°C 92 92°F/ 51.1°C

03 03°F / 1.7°C 18 18°F / 10.0°C 33 33°F / 18.3°C 48 48°F / 26.7°C 63 63°F/ 35.0°C 78 78°F/ 43.3°C 93 93°F/ 51.6°C

04 04°F / 2.2°C 19 19°F / 10.6°C 34 34°F / 18.9°C 49 49°F / 27.2°C 64 64°F/ 35.5°C 79 79°F/ 43.8°C 94 94°F/ 52.2°C
05 05°F / 2.8°C 20 20°F / 11.1°C 35 35°F / 19.4°C 50 50°F / 27.8°C 65 65°F/ 36.1°C 80 80°F/ 44.4°C 95 95°F/ 52.7°C
06 06°F / 3.3°C 21 21°F / 11.7°C 36 36°F / 20.0°C 51 51°F / 28.3°C 66 66°F/ 36.6°C 81 81°F/ 45.0°C 96 96°F/ 53.3°C
07 07°F / 3.9°C 22 22°F / 12.2°C 37 37°F / 20.6°C 52 52°F / 28.9°C 67 67°F/ 37.2°C 82 82°F/ 45.5°C 97 97°F/ 53.8°C
08 08°F / 4.4°C 23 23°F / 12.8°C 38 38°F / 21.1°C 53 53°F / 29.4°C 68 68°F/ 37.7°C 83 83°F/ 46.1°C 98 98°F/ 54.4°C
09 09°F / 5.0°C 24 24°F / 13.3°C 39 39°F / 21.7°C 54 54°F / 30.0°C 69 69°F/ 38.3°C 84 84°F/ 46.6°C 99 99°F/ 55.0°C
10 10°F / 5.6°C 25 25°F / 13.9°C 40 40°F / 22.2°C 55 55°F / 30.6°C 70 70°F/ 38.8°C 85 85°F/ 47.2°C 100 100°F/ 55.5°C
11 11°F / 6.1°C 26 26°F / 14.4°C 41 41°F / 22.8°C 56 56°F / 31.1°C 71 71°F/ 39.4°C 86 86°F/ 47.7°C
12 12°F / 6.7°C 27 27°F / 15.0°C 42 42°F / 23.3°C 57 57°F / 31.7°C 72 72°F/ 40.0°C 87 87°F/ 48.3°C
13 13°F / 7.2°C 28 28°F / 15.6°C 43 43°F / 23.9°C 58 58°F / 32.2°C 73 73°F/ 40.5°C 88 88°F/ 48.8°C
14 14°F / 7.8°C 29 29°F / 16.1°C 44 44°F / 24.4°C 59 59°F / 32.8°C 74 74°F/ 41.1°C 89 89°F/ 49.4°C
15 15°F / 8.3°C 30 30°F / 16.7°C 45 45°F / 25.0°C 60 60°F / 33.3°C 75 75°F/ 41.6°C 90 90°F/ 50.0°C
16 16°F / 8.9°C 31 31°F / 17.2°C 46 46°F / 25.6°C 61 61°F/ 33.8°C 76 76°F/ 42.2°C 91 91°F/ 50.5°C
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

7
Energy Valve Set Up Options
Programmed Ordering Example Continued

5. SELECT CODE FOR ACTUATOR SETUP 6. SELECT CODE FOR CONTROL AND FEEDBACK SIGNAL

NON-SPRING RETURN Code Description

Code Description 0 Control Signal (Y)
DC 0.5 to 10V
1 NO
Feedback Signal (U)
2 NC DC 0.5 to 10V
ELECTRONIC FAIL-SAFE 2 Control Signal (Y)
Code Description DC 2 to 10V

3 NO/FO Feedback Signal (U)

DC 2 to 10V
4 NO/FC
This selection does not affect BACnet functions.
5 NC/FO
6 NC/FC

7. DOES THE ORDER REQUIRE TAGGING?

Part number for tagging: 99981-00101
Valves may be tagged per customer specification. ($10.00 charge per tag)
Example: AHU-1
FCU-2

Part Number for tagging:

99981-00101

COMPLETE PROGRAMMED ORDERING EXAMPLE

EV250S-127+ARX24-EV(00, Z,0,10, 2, 2)

Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

2 - Control and Feedback Signal, 2 to 10V
2 - Normally Closed
10 - Delta T Setpoint, 10°F [5.6°C]
0 - Delta T Manager, OFF
Z - Installed on Return Side
00 - Maximum Flow, 127 GPM

COMPLETE DEFAULT ORDERING EXAMPLE:

EV250S-127+ARB24-EV

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

8
 Control Valve Product Range
Energy Valve Product Range

Valve Nominal
Type Suitable Actuators
Size
DN Non-Spring Electronic
GPM Range Inches 2-way
[mm] Return Fail-Safe
Equal Percentage
1.65 - 5.5* ½ 15 EV050S-055
EV Characteristic

LRB(X)24-EV(-G)
Mode of Operation
3.1 - 10.3* ¾ 20 EV075S-103 The Energy Valve is an energy metering pressure independent
control valve that optimizes, documents, and proves water coil
performance.
5.5 - 18.2* 1 25 EV100S-182
Product Features
Measures Energy: using its built-in electronic flow sensor and
supply and return temperature sensors.

NRB(X)24-EV(-G)
NPT

8.6 - 28.5* 1¼ 32 EV125S-285 Controls Power: with its Power Control logic, providing linear

AKRB(X)24-EV(-G)
heat transfer regardless of temperature and pressure variations.
Manages Delta T: by solving Low Delta T Syndrome. In addition,
11.9 - 39.6* 1½ 40 EV150S-396 it reduces pumping costs while increasing chiller/boiler efficiency
by optimizing coil efficiency.

22.8 - 76.1* 2 50 EV200S-761 Actuator Specifications

Control type modulating
Manual override LR, NR, AR, GR, AKR, GKR, EV, AVK
ARB(X)24-EV(-G)

30-100* 2 50 EV200S-1000** Electrical connection 3 ft. [1 m] cable with ½” conduit fitting

Valve Specifications
38 - 127* 2½ 65 EV250S-127 Service chilled or hot water, 60% glycol
(open loop and steam not allowed)
Flow characteristic equal percentage/linear
54 - 180* 3 80 EV300S-180 Controllable flow range 75°
Flanged ANSI 125

Action stem up - open A to AB

Sizes ½”, ¾”, 1”, 1¼”, 1½”, 2”, 2½’’, 3’’, 4’’, 5’’, 6’’
95 - 317* 4 100 EV400S-317 End fitting NPT female (½”- 2”)
GKRB(X)24-EV
GRB(X)24-EV

pattern to mate with ANSI 125 or 250 flange (2½”- 6”)

Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

Materials
149 - 495* 5 125 EV500S-495 Body
Valve forged brass, nickel plated (½”- 2”)
cast iron - GG25 (2½”- 6”)
Sensor housing forged brass, nickel plated (½”- 2”)
214 - 713* 6 150 EV600S-713
ductile iron - GGG50 (2½”- 6”)
Ball stainless steel
Stem stainless steel
AVKX24-EV-L

38 - 127* 2½ 65 EV250S-127-250
EVX24-EV-L

Plug stainless steel (-250)

Seats Teflon® PTFE, stainless steel (-250)
Characterizing disc Tefzel® (½”- 2”)
stainless steel (2½”- 6”)
54 - 180* 3 80 EV300S-180-250
Flanged ANSI 250

Stem packing EPDM (lubricated), NLP (-250)

Media temp range 14°F to 250°F [-10°C to +120°C],
39°F to 250°F [4°C to 120°C](EV200S-1000)
95 - 317* 4 100 EV400S-317-250 Body pressure rating 360 psi (½”- 2”), ANSI 125, Class B (2½”- 6”)
AVKX24-EV-B

ANSI 250 (2½”-6”) (-250)

EVX24-EV-B

Close-off pressure 200 psi (½”- 2”), 100 psi (2½”- 6”),
149 - 495* 5 125 EV500S-495-250 varies by size (-250)
Differential pressure
range (∆P) see application pages
214 - 713* 6 150 EV600S-713-250 Leakage 0%, ANSI Class IV (-250)
Inlet length to meet
*V’nom = Maximum flow for each valve body size. specified measurement
** Media temperature range is 39°F to 250°F [4­°C to 120°C] accuracy 5x nominal pipe size (NPS)
Communication BACnet IP, BACnet MS/TP, listed by BTL, web
server, Modbus RTU/IP, Belimo MP-Bus
Remote temperature
sensor length
½”- 2” 2 ft. 7.5 in. [0.8 m] short, 9.8 ft. [3 m] long
2½”- 6” 32.8 ft. [10 m]

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

9
Energy Valves
Operation/Installation

SET-UP - Specify Upon Ordering

2-WAY VALVE
NON-SPRING RETURN

LRX...Series NC: Normally Closed- NO: Normally Open-

NRX...Series valve will open as voltage valve will close as voltage
STAYS IN LAST
POSITION

ARX...Series increases. increases.

Y Signal controls the valve position.
GRX...Series
Y Signal
Y Signal controls
controls the
the valve
valve position.
position.
EVX...Series
STAYS IN FAIL-SAFE POSITION

AKRX...Series NO/FO Valve: Normally NO/FC Valve: Normally NC/FO Valve: Normally NC/FC Valve: Normally
ELECTRONIC FAIL-SAFE

GKRX...Series Open-valve will close as Open-valve will close as Closed-valve will open as Closed-valve will open
AVKX...Series voltage increases. voltage increases. voltage increases. as voltage increases.
Y Signal controls the flow.
Fail Action: Will fail open Fail Action: Will fail Fail Action: Will fail open Fail Action: Will fail
Y Signal controls the flow.
upon power loss. closed uponcontrols
Y Signal powertheloss.
flow. upon power loss. closed upon power
loss.
T2
*Feedback signal is always NC Valve is set up at the factory based on customer needs,
T2
see ordering example on page 6-3.
T2

T1
T1
T1
FUNCTIONALITY Y Signal controls the coil thermal power
The Energy Valve offers different operating modes which can be selected using the Web(BTU/hr
setpoint
Y Signal View or
controls orkW).
the ZTHthermal
coil US. power
Y Signal (BTU/hr
setpoint controlsor
thekW).
coil thermal power
setpoint (BTU/hr or kW).
Delta T Manager OFF Delta T Manager ON
T2
Position Control T2 Position Control + Delta T Manager
T2
The Energy Valve works as a normal The Energy Valve works as a pressure
Position Control

pressure dependent valve. The dependent valve. If the measured ∆T is lower

actuator is positioned based on the T1 than the ∆T setpoint the flow will be reduced
DDC control signal. T1 by the Delta T Manager logic to achieve the
T1
setpoint, regardless of the control signal Y.
Y Signal controls the valve position as long
Y
asSignal
the ∆Tcontrols
is abovethe
thevalve position as long Note: In position control, only ∆T Manager can be

Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

Y Signal controls the valve position. ∆T setpoint.
YY Signal Y the ∆Tcontrols
asSignal is abovethe
thevalve
∆T setpoint.
position as long selected, ∆T Manager Scaling will not be available.
Signal controls the valve
controls the valveposition.
position.
as the ∆T is above the ∆T setpoint.

T2
Pressure Independent Flow Control T2 Pressure Independent Flow Control+
The Energy Valve works as an ePIV T2 Delta T Manager
Flow Control

(Electronic Pressure Independent The Energy Valve works as an ePIV. However,

Valve). The valve reacts to any T1
if the measured ∆T is lower than the ∆T
change in pressure and modulates T1 setpoint, the flow will be reduced by the Delta
the actuator to maintain the flow T1 T Manager logic to achieve the ∆T setpoint,
Y Signal controls the flow. setpoint based on the DDC control regardless of the control signal Y.
Y Signal controls the flow as long as the ∆T
Y
is Signal
above controls the flow as long as the ∆T
YY Signal
Signal controls
controls the
the flow.
flow. signal. the ∆T setpoint.
is above the
Y Signal ∆T setpoint.
controls the flow as long as the ∆T
is above the ∆T setpoint.
T2
Power Control Power Control + Delta T Manager
T2 T2
T2 The Energy Valve adjusts flow to T2 The Energy Valve adjusts flow to maintain
maintain the thermal power setpoint. T2 the thermal power setpoint. If the measured
Power Control

If the measured coil power is below coil power is below setpoint, flow will be
T1
setpoint, flow will be increased. If increased. If the measured coil power is
T1 T1
T1
the measured coil power is above T1 above setpoint, flow will be decreased as long
setpoint, flow will be decreased as T1
as the defined V’max is not exceeded. If the
Y Signal controls the coil thermal power
setpoint long as the defined V’max is not measured ∆T is lower than the ∆T setpoint,
Y Signal(BTU/hr
controlsorthekW).
coil thermal power Y Signal controls the thermal power
Ysetpoint
Signal (BTU/hr
controlsorthekW).
coil thermal power exceeded. Y Signal as
setpoint controls
long asthethe
thermal power the ∆T
∆T is above flow will be reduced by the Delta T Manager
setpoint as long as the ∆T is above the ∆T
setpoint (BTU/hr or kW). setpoint.
Y Signal
setpoint. controls the thermal power logic and will override the thermal power
setpoint as long as the ∆T is above the ∆T control setpoint.
T2 setpoint.
Note: When in Power Control T2
mode, a failure in any temperature sensor will cause the valve to operate in Flow Control mode. A failure in the flow sensor, will cause the
valve to operate in Position TControl
2 mode. When the situation is rectified, the valve will revert to its Control Mode setting.

T1
T1

T1
Y Signal controls the valve position as long
as
Y Signal 800-543-9038
the ∆Tcontrols
is above thevalve
the ∆T setpoint.USA
position as long 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN
as the ∆T is above the ∆T setpoint.
10 Y Signal controls the valve position as long
as the ∆T is above the ∆T setpoint.
 Energy Valve
Installation

Piping
The Energy Valve is recommended to be installed on the
return side of the coil. This diagram illustrates a typical
application. Consult engineering specification and drawings
for particular circumstances.

For 2½” through 6” valves, install the provided thermowell

on the other side of the coil (T1). For ½” through 2” valves,
both temperature sensors are remote and are supplied with
female NPT threaded pipe body. The (T2) sensor should be
installed downstream in the direction of flow after the valve
assembly. The (T1) sensor should be installed on the other
side of the coil.

Belimo recommends installing one strainer per system. If

the system has multiple branches, it is recommended to install
one strainer per branch.

Installation

Inlet Length ½” - 2” [DN15-DN50]

The Energy Valve requires a section of straight pipe on the valve inlet to
achieve the flow accuracy specified. This section should be
at least 5 pipe diameters long with respect to the size of the valve.
Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

½” [DN15] 5 x nominal pipe size = 2.5” [64 mm] 5 x Nominal Pipe Size (NPS)

¾” [DN20] 5 x nominal pipe size = 3.75” [95 mm]

1” [DN25] 5 x nominal pipe size = 5” [127 mm]
2½” - 6” [DN65-DN150]
1¼” [DN32] 5 x nominal pipe size = 6.25” [159 mm] ANSI 125
1½” [DN40] 5 x nominal pipe size = 7.5” [191 mm]
2” [DN50] 5 x nominal pipe size = 10” [254 mm]
5 x Nominal Pipe Size (NPS)

2½” [DN65] 5 x nominal pipe size = 12.5” [317 mm]

3” [DN80] 5 x nominal pipe size = 15” [381 mm]
4” [DN100] 5 x nominal pipe size = 20” [508 mm]
5” [DN125] 5 x nominal pipe size = 25” [635 mm]
2½” - 6” [DN65-DN150]
6” [DN150] 5 x nominal pipe size = 30” [762 mm] ANSI 250

Outlet Length
No requirements for outlet length.
Elbows can be installed directly after the valve.
5 x Nominal Pipe Size (NPS)

Handling
Lift the Energy Valve from the valve body. Do not lift this product by
the actuator. Lifting the product by the actuator can break the linkage
and void the warranty.

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

11
Energy Valve
Installation

Remote Sensor Installation:

½” [DN 15] to 2” [DN 50]
Two remote sensors with female NPT pipe bodies are provided with the Energy Valve and must be installed on opposite sides of the coil.
Temperature Sensor 1 (T1) is equipped with a longer sensor cable than Temperature Sensor 2 (T2). It is recommended that the Energy Valve is
installed on the return side of the coil. The T1 sensor will be on the supply side and the T2 sensor will be on the return. The T2 sensor should be
installed upstream in the direction of the flow after the valve.

Female NPT Dimensions

IN DN [mm] A B C D E
½ 15 ½” NPT 0.6” 2.06” 0.62” 0.76”
¾ 20 ¾” NPT 0.65” 2.24” 0.82” 0.63”
1 25 1” NPT 0.76” 2.54” 1.02” 0.53”
1¼ 32 1¼” NPT 0.85” 2.77” 1.29” 1.61”
1½ 40 1½” NPT 0.87” 2.77” 1.61” 1.77”
2 50 2” NPT 1.04” 3.16” 2.00” 2.00”

2½” [DN 65] to 6” [DN 150]

A thermowell is provided with the remote temperature sensor. The well should be installed on the pipe prior to installing the remote temperature
sensor. The remote temperature sensor should be installed on the opposite pipe entering the coil from where the Energy Valve is installed. A ½”
NPT female union should be welded on the pipe to allow the installation of the thermowell. The Energy Valve is equipped with a 32 ft. [10 m] cable
for the remote sensor. If a shorter remote sensor cable is required, the cable is also available in the following sizes: 4.9 ft. [1.5 m], 9.8 ft. [3 m], or
16.4 ft. [5 m]. Order the appropriate size for the application.

Note: If a different sensor with a different cable length has been installed, the change must be applied to the Energy Valve Web View Settings.

Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

Refer to Web View Settings table on page 33.
Do not cut sensor cables, this will produce inaccurate data. Belimo offers different sensor cabling lengths options.

Remote Well Installation Dimensional Parameters

IN DN [mm] EL ET L max.
2½ 65 3.66” [93] 2.36” [60] 1.18” [30]
3 80 3.66” [93] 2.36” [60] 1.18” [30]
4 100 3.66” [93] 2.36” [60] 1.18” [30]
5 125 3.66” [93] 2.36” [60] 1.18” [30]
6 150 3.66” [93] 2.36” [60] 1.18” [30]

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

12
 Energy Valve
Installation

Actuator, Temperature & Flow Sensor Replacement

The actuator, temperature sensors, and the flow sensor can be removed from the valve, if needed. Actuator and flow sensor must be replaced
together. Either temperature sensor can be removed without draining the system; each temperature sensor is inserted in a thermowell.

½” to 2” Energy Valves
The flow sensor is part of the flow unit. The flow unit consists of the ultrasonic flow sensor and housing.
The flow sensor cannot be separated from its flow housing. To separate the flow unit from the valve
assembly, unthread the coupler/union that connects the flow housing to the control valve assembly.
Note: The coupler thread is a straight pipe thread.

2½” to 6” Energy Valves (Electromagnetic)

The flow sensor can be separated from its flow housing. To remove the flow sensor from the housing,
loosen the threaded plastic locking nut. To assemble, ensure the O-ring and flange locking ring are in
place. Hand tighten the threaded plastic locking nut. Note: The flanged sensor housing and flanged
valve bodies do not need to be disassembled.

IMPORTANT: The flow sensor is directly embedded in the flow housing. Before removing the flow
sensor, the system must be relieved of pressure, drained and or closed directly upstream and downstream of the valve to circumvent any system
leakage. The valve must not be lifted from the flow sensor or actuator. Disassembly and or lifting by the actuator or flow sensor will damage the
assembly and void warranty.

Note: If a different sensor with a different cable length has been installed, the change must be applied to the Energy Valve Web View Settings.
Refer to Web View Settings table on page 33.
Do not cut sensor cables, this will produce inaccurate data. Belimo offers different sensor cabling lengths options.

Orientation
Energy Valve shall be installed with flow in the direction of the arrow on the valve body.
Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

The valve assembly can be installed in a vertical or horizontal arrangement, as long as the actuator is positioned to avoid
condensation from dripping onto the actuator.

(Not for use with weather shields)

Insulation Insulation

The insulation should be below the actuator.

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

13
Energy Valve
Installation

Installation

1. Inspect shipping package, valve, linkage, and actuator for physical Valve should not be used for combustible gas applications. Gas leaks
damage. If shipping damage has occurred, notify appropriate and explosions may result.
carrier. Do not install. Do not install in systems, which exceed the ratings of the valve.
2. If a replacement, remove existing valve, linkage and actuator from • Avoid installations where valve may be exposed to excessive
the piping system. moisture, corrosive fumes, vibration, high ambient temperatures,
3. If actuator and linkage are removed, they must be reinstalled elements, or high traffic areas with potential for mechanical
correctly. The actuator must be rotated so that the valve seats damage.
properly close off. • Valve assembly location must be within ambient ratings of actuator.
4. Install valve with the proper ports as inlets and outlets. Check that If temperature is below -22°F, a heater is required.
inlet and outlet of 2-way valves are correct. Flow direction arrows • Valve assembly will require heat shielding, thermal isolation, or
must be correct. cooling if combined effect of medium and ambient temperatures
5. Blow out all piping and thoroughly clean before valve installation. – conduction, convection, and radiation– is above 122°F for
6. Clean flanges with wire brush and rag. Clean pipes, flanges, and prolonged periods at the actuator.
valve flanges before installation; check for any foreign material • Visual access must be provided. Assembly must be accessible for
that can become lodged in trim components. Strainers should be routine schedule service. Contractor should provide unions for
cleaned after initial startup. removal from line and isolation valves.
7. Valve must be installed with the stem towards the vertical, not below • Avoid excessive stresses. Mechanical support must be provided
horizontal. See Orientation on page 15. where reducers have been used and the piping system may have
8. These valves are designed to be installed between ANSI Class less structural integrity than full pipe sizes.
125/150 flanges only. • Sufficient upstream piping runs must be provided to ensure proper
9. -250 models are designed to be installed between ANSI Class valve capacity and flow response. See installation section for details.
250/300 flanges only. • Life span of valve stems and O-rings is dependent on maintaining
10. Carefully follow installation using ANSI piping practices. non-damaging conditions. Poor water treatment or filtration,
corrosion, scale, other particulate can result in damage to trim
components. A water treatment specialist should be consulted.
• It is not necessary to install one strainer per unit. Belimo
recommends installing one strainer per system. If the system has
multiple branches, it is recommended to install one strainer per
branch.

Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

14
 Energy Valve
Wiring Diagrams

Wiring Diagrams

A Actuators with appliance cables are numbered. 24 VAC Transformer A 2 3 7 18

2 CAUTION Equipment damage! Blk (1) Common
T
Line
Actuators may be connected in parallel.
Volts Red (2) Hot +
Power consumption and input impedance must be observed.
Wht (3) Y-Input

Cable 1
3 Actuators may also be powered by 24 VDC. (4 to 20 mA)
Org (5) U-Output
A 500 Ω resistor converts the 4 to 20 mA control signal to 2 Pnk (6) C1BACnet MS/TP -
7 to 10 VDC. C1 Modbus RTU +
Gry (7) C2 BACnet MS/TP +
Actuators with plenum rated cable do not have numbers on C2 Modbus RTU +
18 wires; use color codes instead.

Cable T2 Cable T1
Wht (1) S T

Red (2) S1

Meets cULus requirements without the need of an electrical Wht (1) S T

ground connection Red (2) S2

WARNING Live Electrical Components!

During installation, testing, servicing and troubleshooting of this 4-20 mA
product, it may be necessary to work with live electrical components. Have a
qualified licensed electrician or other individual who has been properly
trained in handling live electrical components perform these tasks. Failure to
follow all electrical safety precautions when exposed to live electrical
components could result in death or serious injury.

NOTE: BACnet set point writing will deactivate Analog Signal input.
Valve power must be cycled to reactivate its response to analog signal.

System Ground
2 to 10 VDC Control
24 VAC Transformer A 2 3 18
In cases where the valve body is electrically isolated
from the water pipe, an earth ground should be
Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

Line Blk (1) Common

T

Volts Red (2) Hot +

installed in order for the sensor to work properly.
Earth ground can be connected directly on the
Control Signal (-)
Cable 1

2 to 10 VDC (+) Wht (3) Y-Input

sensor body. A connection point is provided on the
(-) flange of the sensor body.
2 to 10 VDC
Feedback Signal (+) Org (5) U-Output

Pnk (6) C1 BACnet MS/TP -

C1 Modbus RTU -
Gry (7) C2 BACnet MS/TP +
C2 Modbus RTU +
Cable T1

Wht (1) S T

Red (2) S1
Cable T2

Wht (1) S T

Red (2) S2

RJ-45
Ethernet

BACnet IP
Modbus IP

2-10 VDC, BACnet MSTP/IP, Modbus RTU/IP

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

15
Energy Valve
Control Mode Sequence of Operation

Flow Control
performance. The valve will react to changes in system pressure and to
To set the Energy Valve to Flow Control, set the Control Mode to Flow changes in water differential temperature to match the power setpoint
Control in the Setting area of the Web View, under Configuration from the controller.
Control Function. Refer Web View settings table on page 33.
Power Control / Sequence of Operation
Flow Control Application The Energy Valve uses its ultrasonic or magnetic flow meter and logic
Use Flow Control to achieve pressure independent valve performance. to throttle its characterized control valve to maintain the power set
The valve will react to changes in system pressure to match the flow point. The valve will respond to the DDC power analog signal except
setpoint from the controller. when the current power is within ±5% of the signal.
When the Delta T Manager is enabled, it will activate its logic when the
Flow Control Sequence of Operation
actual ∆T drops 2°F below the dT setpoint. It does this by throttling
The Energy Valve uses its ultrasonic or magnetic flow meter and logic the valve close until the dT setpoint is reached. The Energy Valve will
to throttle its characterized control valve (CCV) to maintain the flow resume its normal operation based on the DDC signal; when the DDC
set point. The valve will respond to the DDC flow analog signal except setpoint drops 5% of V’max below the Delta T Manager’s current flow.
when the current flow is within ±5% of the signal. The Delta T Manager will not operate when the flow is below 30% of
When the Delta T Manager is enabled, it will activate its logic when the V’max. In addition, the Delta T Manager minimum flow will always be
actual ∆T drops 2°F below the dT Setpoint. It does that by throttling greater than 30% of V’max. The flow also needs to be above 30% of
the valve close until the dT setpoint is reached. The Energy Valve will v’max for 5 minutes before the Delta T Manager will engage. 30% is
resume its normal operation based on the DDC signal when the DDC the default however for specific applications it is possible to operate
setpoint drops 5% of V’max below the Delta T Manager’s current flow. the Delta T Manager down to 10% of V’nom. This setting is available in
The Delta T Manager will not operate when the flow is below 30% of Webview on the settings tab under the Delta T Management section.
V’max. In addition, the Delta T Manager minimum flow will always be With Power Control, the Energy Valve is pressure and temperature
greater than 30% of V’max. The flow also needs to be above 30% of independent over its entire throttling range with available differential
v’max for 5 minutes before the Delta T Manager will engage. 30% is pressure from 1-50 psid. When the available differential pressure is
the default however for specific applications it is possible to operate less than 5 psid, refer to the Flow Reduction table on page 43 to verify
the Delta T Manager down to 10% of V’nom. This setting is available in adequate differential pressure to obtain desired V’max and associated
Webview on the settings tab under the Delta T Management section. P’max.
The Energy Valve is pressure independent over its entire throttling
range with available differential pressure from 1-50 psid. When the
available differential pressure is less than 5 psid, refer to the Flow Position Control
Reduction Chart to verify adequate differential pressure to obtain
desired V’max. To set the Energy Valve to Position Control, set the Control Mode

Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

to Position Control in the Settings area of the Web View, under
Configuration Control Function. Refer to the Web View Settings table
Power Control on page 33.

Position Control Application

To set the Energy Valve to Power Control, set the Control Mode
to Power Control in the Settings area of the Web View, under Use Position Control to achieve pressure dependent valve performance
Configuration Control Function. Refer to Web View Settings table on or to verify control response during installation, maintenance and
page 33. troubleshooting. The flow meter will report actual flow at all valve
positions.
Power Control Application
Use Power Control to achieve a precise linear power output of the heat
exchanger over its operating range. Power Control combines pressure
independent valve performance with temperature independent coil

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

16
 Energy Valve
Control Mode Sequence of Operation

Position Control Sequence of Operation Graphical dT Manager and dT Manager Scaling Operation
The Energy Valve uses position feedback and logic to throttle its In the graphs shown below, the blue and red data points were captured
characterized control valve to maintain the valve position. The valve by allowing the Energy Valve to operate with the Delta T Manager
will respond to the DDC position analog signal except when the disable and under normal operating conditions for a sufficient period
position is within ±5% of the signal. to collect data ranging from light to full load.
Unrestricted flow shown with blue data points occur when the dT
manager is inactive. Restricted flow shown with red data points would
Delta T Manager Options be eliminated when dT Manager is active.

To configure the Delta T Manager options, set the Configuration dT-

Manager in the Settings area of the Web View. Refer to the Web View
Settings table on page 29.
The Delta T Manager monitors the ∆T across the coil. When the ∆T
drops below the set point, the Delta T Manager logic throttles the valve
close to increase ∆T above the setpoint. When the Delta T Manager is
enabled, it will activate its logic when the actual ∆T drops 2°F below
the dT Setpoint. It does that by throttling the valve close until the dT
setpoint is reached. The Energy Valve will resume its normal operation
based on the DDC signal when the DDC setpoint drops 5% of V’max
below the Delta T Manager’s current flow. The Delta T Manager will
not operate when the flow is below 30% of V’max. In addition, the
Delta T Manager minimum flow will always be greater than 30% of
V’max. The flow also needs to be above 30% of v’max for 5 minutes
before the Delta T Manager will engage. Two Delta T Manager options
are available: dT Manager and dT Manager Scaling. 30% is the default
however for specific applications it is possible to operate the Delta T
Manager down to 10% of V’nom. This setting is available in Webview Typical Representation of dT Manager Function with Flow Control
on the settings tab under the Delta T Management section. or Power Control
dT Manager Application
Use dT Manager to assure circuit overflow is eliminated below the
Delta T Limit Value. Limiting function can be applied to all Control
Modes of operation; Flow, Power and Position. Belimo suggests using
Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

this mode with changing air mass flow rate.

Sequence of Operation
This logic when activated will limit the heat exchanger ∆T to a fixed dT
setpoint by reducing valve flow. The dT setpoint is equal to the Delta T
Limiting Value found in Web View settings.

dT Manager Scaling Application

This limiting function can be applied to all control modes of operation:
flow and power. Building operators are assured circuit overflow is
eliminated below the scaled (variable) dT setpoint. Belimo suggests
using this mode with changing temperature of the inlet air flow or inlet
water supply. Typical Representation of dT Manager Scaling Function with Flow
Control or Power Control
Sequence of Operation
This logic when activated will limit the heat exchanger ∆T to a scaled
(variable) dT setpoint by reducing valve flow. The dT setpoint =
(Delta T Limit Value /Flow Saturation Value)* (actual flow). The Flow
Saturation Value found in Web View is a required setting for this logic.

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

17
Energy Valve
Web View

The Energy Valve Web View is a built-in web server that is used to configure the valve settings and view current and historical data.
It can be accessed from a computer with a web browser. The Energy Valve must be connected to a TCP/IP network.

Connecting the Energy

Valve to Ethernet
To configure the Energy Valve using
Web View the Energy Valve must be
connected to a TCP/IP network. If
connecting the Energy Valve to a
laptop computer directly using a static
connection without connecting to a
LAN, configure the laptop IP address
to 192.168.0.200 before connecting
to the Energy Valve. Then open a web
browser and type in the following
address in the web browser address bar:
http://192.168.0.10:8080

If connecting the Energy Valve to a

laptop computer directly using a
dynamic peer to peer connection without connecting to a LAN, no laptop IP configuration is required, open a web browser and
type in the following address in the web browser address bar: http://belimo.local:8080

This address is printed on the side of the Energy Valve actuator.

Compatible Browsers

Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

Browsers must be capable of running Javascript.
• Internet Explorer 8 or newer
• Firefox 27 or newer
• Chrome 33 or newer
• Safari 5.17 or newer
• Android browser
• Windows Phone

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

18
 Energy Valve
Web View

Login
•• Access to the actuator is protected by the
user name and password.
• Three default user types are available to
login. Each user type has different security
rights to the Web View. Refer to Web View
user table below.
• Belimo cannot recover IP address. IP
address can be viewed with ZTH US tool.

Web View User Table Username: Guest Maintenance Admin

Password*: guest belimo Contact
Belimo Tech
Support
Web View Page
Dashboard Read Read Read
Overview Read Read/Write Read/Write
Override and Trend Read Read/Write Read/Write
Control
Data Log Chart Read Read Read/Write
Settings Read Read Read/Write
Status Read Read/Write Read/Write
Date & Time Settings -- Read/Write Read/Write
IP Settings -- Read/Write Read/Write
Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

Version Information -- Read/Write Read/Write

Mobile Read Read Read/Write
Data Logging Read Read Read/Write
BACnet / MP Settings Read Read Read/Write
*Password is case sensitive

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

19
Energy Valve
Web View

The Energy Valve Web View is a graphical user interface accessed via a network or internet to set up, calibrate and change the
parameters of the Belimo Energy Valve. The Web View consists of the following page views:

Overview
The overview page allows you to see the
setpoint, flow, valve position, glycol percentage
if activated, Delta T, and mode of operation.
Double click on a heading item to see a
historical trend of the data.

Data
An analytical view of the
historical data with the ability
to select the type of data to
analyze; primarily used for
maintenance and

Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

troubleshooting.

This view also, provides key

performance indicators In
addition this view also has
the Delta T set point suggestion
integrated. To calculate press
the coil characteristic button
below x axis.

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

20
 Energy Valve
Web View

Status

Status provides an error count by type and time elapsed

of last occurrence. More details provides additional
information with informational buttons on the possible
solution to the error.

These errors can be reset to zero and should be reset

after commissioning to clear any errors that may have
occurred due to the valve and system not being fully
operational.

Settings

Access and adjust the operating settings. Refer to

Web View Settings table on page 33.
Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

21
Energy Valve
Web View
Configuration Options
Date and Time Settings
Provides different ways to set the date and time. It allows the
time to be entered manually, synchronized through a computer,
or synchronized with a Time Server.
If BACnet communication is enabled, Local Client Date and Time
will be automated through BACnet.

IP Settings

To configure the valve communication on a TCP/IP network. It

allows the valve to have a dynamic IP address (requires an active
DHCP server) or a static IP address (requires an IP address,
Network Mask and Gateway address from IT manager). The
Broadcast address will be generated automatically.

The DNS Servers are listed here for default. If different are

Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

preferred they will need to be assigned by the customer IT
infrastructure responsible for the Energy Valve installation.

Version Information
Displays current software version.

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

22
 Energy Valve
Web View
Data Logging
Location to download all the historical data in a spreadsheet (.csv) that
can be uploaded to the Data Analysis Tool™ for further analysis. See Data
Analysis Tool™ page.

User Administration
Add, delete and edit including password management for users. See Webview
User table for User profiles.

Maintenance
Maintenance: Configuration Import /Export
This feature allows the Energy Valve settings
to be downloaded (export configuration) from
one valve and imported to another valve via an
Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

XML file format. The valve size and actuator

type need to be the same for this function.
Activation Codes: This feature is for uploading
a code for additional features such as glycol
monitoring. This code and pricing can be
provided by Belimo Technical support.
Update: Last Update indicates the status
of updates for security and operational
performance.
No Updates applied – none of available have
been executed.
Update available in cloud.
No new updates available
Apply Available Updates
Executes downloaded updates
Upload and Apply Update File
Downloads available updates and executes

Misc: Reboot - Performs the function of power cycling the actuator for a restart. Factory Reset restores the Energy Valve actuator
settings to settings when it left the Belimo factory.

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

23
Energy Valve
Web View

BACnet, MP-Slave and Modbus Settings

This page is used to set the type of communication and settings for the
Energy Valve. All BACnet configurations must be set prior to connecting to the
BACnet network to avoid communication and settings problems.
• BACnet is a building automation communication protocol worldwide standard.
• MP is a Belimo protocol that allows for communication to multiple Belimo
devices at the same time.
• Modbus is also a building automation communication protocol
• None is the default value, when selected the valve will not communicate via BACnet.

BACnet IP Settings
Port: The UDP port value defaulted to 47808
Simple/Foreign Device: A Simple Device requires communication
only on its own IP subnet, or there is a BBMD device on its subnet
to handle routing of broadcast messages between subnets. A
Foreign Device communicates to devices on subnets other than
its own and to do so, must register with a BBMD device on a remote
subnet.
Instance ID: A unique ID number for the EV device object on the
BACnet network (between 0 and 4194303). This is *not* a read only
value.
Device Name: Name used to represent the device in the BACnet
system.
Device Description: General detail of the device.

Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

System Status: Indicates that the valve is operational. A read only
value. 0 is operational, 1 is not operational.
Protocol Version and Revision: These are read only values to show
the BACnet protocol version and revision that the communication
software follows.
IP BBMD: IP address entered must be the address of the BBMD
router on a different subnet.
Time to Live: The time in seconds between updated registrations
with the BBMD router. If your BBMD router has a TTL setting, this
value should match the router’s.

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

24
 Energy Valve
Web View

BACnet MS/TP Settings

Baud Rate: The transmission speed within the MS/TP
network. All devices on the same network must be set to
the same baud rate. Available rates: 9600, 19200, 38400,
76800, 115200.
MAC: The MAC address on the MS/TP network. This number
must be unique within the network. Available values range
from 1 to 127.
Max Master: Max_Master must be large enough that all
MS/TP MAC addresses are within it. If unsure, set to 127.
120 Ohm Termination: MS/TP networks require termination
resistors on end-of-line devices. Turning on this setting
will provide the required 120 Ohm termination on this
BACnet device. Use this setting with great caution as adding
termination resistance on a device in the middle of a network
can cause significant network problems.
Instance ID: A unique ID number for the EV device object on
the BACnet network (between 0 and 4194303). This is *not* a
read only value.
Device Name: Name used to represent the device in the
BACnet system.
System Status: Indicates that the valve is operational. A read
only value. 0 is operational, 1 is not operational.
Protocol Version and Revision: These are read only values
to show the BACnet protocol version and revision that the
communication software follows.
Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

MS/TP Device Load: The MS/TP interface on the Energy

Valve will create a 5/8 unit load on the network. This is a combination of local biasing resistors and a 1/8 load
EIA-485 driver chip. Please keep this load figure in mind while determining network device limits and repeater requirements. For
reference, the EIA-485 specification allows for a total of 32 device loads on a network without using repeaters. The transceiver is
isolated, but the isolated reference is not exposed due to lack of pins 47K pull up resistors are connected from the isolated common
to – and isolated 5v to + and is fail safe.

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

25
Energy Valve
Web View
Modbus TCP Settings
TCP Unit ID: Each device in a network is assigned a unique unit address from
1 to 247.
Default Value: 1

TCP Port: Modbus is a serial communications protocol for client-server

communication between a switch (server) and a device in the network running
Modbus client software (client), A client sends a message to a TCP port on the
switch.
The listening TCP port 502 is reserved for Modbus communications. It is
mandatory to listen by default on that port. However, some markets or
applications might require that another port is dedicated to Modbus over TCP.
This is the case when interoperability is required with non =S=products, such as in Building Control. For that reason, it is highly
recommended that the clients and the servers give the possibility to the user to parameterize the Modbus over TCP port number. It is
important to note that even if another TCP server port is configured for Modbus service in certain applications, TCP server port 502
must still be available in addition to any application specific ports.

Keep Open timeout [seconds]: How long a device can take to respond before it is considered a timeout
Default Value: 30 seconds

Modbus RTU Settings

Modbus Address: Each device in a network is assigned a unique unit address

Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

from 1 to 247.
Default Value: 1
Range: 1 -247
Baud rate: The transmission speed within the Modbus RTU network. All devices
on the same network must be set to the same baud rate.
Default Value: 38400
Range: 9600, 19200, 38400, 76800, 115200
Parity: The transmission format used by Modbus that indicates the start buts,
data bits, parity and stop bits.
Default Value: 1-8-N-2
Range:
1-8-N-1 (1 start, 8 data, no parity, 1 stop bit)
1-8-N-2 (1 start, 8 data, no parity, 2 stop bit)
1-8-E-1 (1 start, 8 data, even parity, 1 stop bit)
1-8-O-1 (1 start, 8 data, odd parity, 1 stop bit)

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

26
 Energy Valve
Cloud Settings
Cloud Setting
Datalog Service Connection Status: The status of the cloud connection.
Cloud Server: The address of the connected host Server.
MAC Address: The MAC address of the connected Energy Valve.
Datalog Service: Allows for data transfer between the Energy Valve
and the cloud.
Task Service: Allows for automatic updating of the Energy Valve flow
and Delta T setpoints based on data captured by the valve in the cloud.
Update Mode: Allows for automatic updating of the Energy Valve flow
and Delta T setpoints based on data captured by the valve in the cloud.
Disabled: No updates are downloaded.
Device_Controlled: Updates are shown on the Maintenance page in
Webview and not installed automatically, they are offered.
Cloud_Controlled_Manual: The updates need to be released by the
device owner in the cloud. The device installs the update immediately
after release.
Cloud_Controlled Auto: The updates are released by Belimo and
propagated to the devices. The device installs the update immediately
after release.
Current owner: The individual that has current ownership of the device.
This is typically the name of the user that configured the cloud settings and corresponds to the email address provided on initial set
up.
Refresh Current owner: Simple refresh button to explicitly ask the cloud to tell us the current owner (for example after the product
was transferred in the cloud).
New owner: Used when starting a transfer from a current owner (or no owner yet) to a new owner which requires pressing the
Transfer device button after new owner is entered.
Additional Information: By clicking on the load button displays more ownership information and device details.
Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

Connection Status: Runs a routine that will help troubleshoot connection to the Belimo cloud.

Connection setup

Connectivity Requirements:
Customer provided Ethernet Cable
Dedicated Internet Connection

Requirements for cloud connection

Gateway IP Address that allows a route to the internet
In case of DNS restrictions: IP addresses of internal DNS servers
Communication details
Used protocol is https
Port of the server endpoint: 443
DNS address of cloud server: https://connect.g2bcc.com

Firewall rule to allow communication

Action: Pass / Allow
Address family: IPv4
Protocol: https over TCP
Source: IP address of device or subnet designated to EnergyValve devices
Destination: https://connect.g2bcc.com

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

27
Energy Valve
Cloud Settings
Daily Data Volume
Approximately 10MB

Communication between device and cloud

All communication between the device and the cloud is encrypted. The data is not readable without de-encryption.

Local configuration
In order to configure the device, the local webpage running on the integrated webserver has to be reached. The steps necessary
depend on the local network setup and can vary. The easiest way to open the webpage is a direct LAN connection with a laptop running
Windows and using the address http://belimo.local:8080 (the port number is 8080). Alternatives include, but are not limited to:
using a wireless access point that connects to the device by LAN cable, then use any portable device with a web browser to open the
webpage from any internal network location if the LAN setup, especially routing and switching settings are appropriate using a direct
LAN connection with the correct network settings (IP address and subnet mask) and accessing the device with its initial fixed IP (e.g.
http://192.168.0.1:8080)
The website asks for login credentials. In order to configure the device for cloud access including network settings an admin user type
is necessary. The login credentials for the admin user are not publicly available, but communicated through customer support. The
user is forced to change the admin password while completing the installation assistant.
There is an initial installation assistant as well as a manual method to configure the device to access the cloud. The following user data
is requested when the user wants to enable cloud functionality:
Mandatory data:
Cloud E-Mail Account (valid E-Mail address, note: no need that this E-Mail address already is a valid Belimo cloud account)

Cloud Connectivity Quick Start Guide

1. Locally Configure IP Settings on Actuator using LAN connection

and laptop via http://belimo.local:8080

Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

28
 Energy Valve
Cloud Settings
2. Ownership Information and acknowledgement of
cloud services.

When the actuator is powered up initially the

installation assistant is run and relevant cloud setup
information like device owner and email address is
entered as well as some valve set up information. To
ensure this is complete the set up assistant can be
started again by clicking the start wizard icon on
the submenu application under the settings menu
heading.

3. Once actuator has been locally configured with appropriate IP address, email address, device owner and acknowledgement of cloud
services, connect live Ethernet cable and log back into the actuator via the IP network and verify connection to the Belimo cloud.
Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

4. Go to cloud.belimo.com to create an account and allow

device entrance into the cloud. The email address entered
when completing the set up wizard will be required when
creating the cloud account.

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

29
Energy Valve
Cloud Settings
5. Once connected the following services will be available:

Delta T Optimization and Performance Reporting Lifetime Data Access

Flow Setpoints
Key performance indicators are Secure, single consolidated
Cloud analytics provide graphically illustrated showing repository that stores and
recommended Delta T and flow current and historical performance provides system data access for
setpoints which can be updated data of flow rates, energy usage, future optimization.
remotely or automatically to save Delta T, and other points of interest.
time and improve efficiency.

Online Tech Support Software Updates Extended Warranty

Belimo’s industry leading technical Latest software and security 5-year warranty is increased
support team available to assist updates automatically provided to 7- year with Belimo cloud
you remotely. for maximum productivity and connection.**
reliability.

**The following provision supplements the applicable Terms and Conditions of Sale for the Energy Valve 3.0. The 5-year warranty foreseen in the Terms and
Conditions of Sale shall be replaced by a 7-year warranty, provided the following conditions are fulfilled:
• The Cloud-connection on the respective BELIMO device is activated
• The respective BELIMO device has been allocated to a Cloud-Account
• At the time of the warranty claim the connection ratio between the BELIMO device and the BELIMO-Cloud is at least 90% (the connection ratio is
determined by the amount of hours of Cloud-connection of the BELIMO device divided by its operating hours).

Cloud Interface

Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

Overview Page
Status of Devices:
Provides Total Energy Valves for
associated account. Only valves for the
account will be displayed. Also indicated
here is if there are problems with the device
in terms of operation that may need attention
and if there are valves coming in or leaving
the cloud via transfer.

Devices:
Displays the device name which is assigned in Webview by the user, Health status, Serial Number of the Energy Valve and the current
device owner. Clicking on the action folder displays the Valve data points, ability to download data, Valve details and transfer capability.

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

30
 Energy Valve
Cloud Settings
Device Management Page
Provides a single page focused on managing the
Energy Valve in the cloud. Displays the device
name which is assigned in Webview by the user,
Health status, Serial Number of the Energy Valve
and the current device owner. There is also search
functionality that allows for search by serial
number or Energy Valve name.

Under the Action heading are 3 specific functions:

1. Transfer Energy Valve from one owner to

another by clicking on the orange arrow. To
have data available for the new owner, the
option of with data should be selected. This
appears once the transfer icon is clicked.
2. Display Valve data points, ability to download data, Valve details and transfer capability by clicking the action folder.
3. Delete the selected Energy valve from the cloud by clicking the trash can icon.

Settings Page
Provides page focused on the information for two main areas
Account Settings which includes information about the user/
owner including Name, Geographic information, Email address,
and current password as well as ability to change current
password. Also My User Groups which displays the current user
groups and ability to create a new group and add members to it.
Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

31
Energy Valve
Cloud Settings

Transfer Energy Valve From One Owner to Another or Group

Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

32
 Energy Valve
Cloud Settings
Support Page
Provides relevant support information,
Contact for Belimo Headquarters,
Support Request, API Developer
Documentation and Delta T Optimize
Request. For the Delta T Optimize
request it requires at least 2 months
of data for proper analysis.

Field Programming and 1

Commissioning Options 6

All Energy Valve actuators can be field

Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

programmed with either the ZTH US 2

handheld tool or with an Ethernet cable
connected to a computer with web
browser to access the actuator’s web
page (Web View). Refer to the table 7
below for a list of settings than can be 3
changed in the field.

8
4

9
5

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

33
Energy Valve
Cloud Settings

Web View Settings

TAB SETTING FUNCTION DEFAULT / RANGE

Valve Size Defines the full flow cataloged capacity (V’nom) of the valve. (Default factory set to the valve
1. General Information

size)
½” – 6” [DN 15 – DN 150]

Set Up Assistant A set up routine that runs on first power up to assist the installer with N/A
configuring the valve. Can also be run again by selecting here and any
changes made will be applied.

Import/ Export Allows the export of valve settings and Import into another valve in XML N/A
2. Functions

Format.
Comissioning Report Generates a PDF of valve configuration settings for records. N/A

Temperature Units: water supply, return, and delta T. Fahrenheit

Celsius, Kelvin
Flow Units: water flow rate through the valve. GPM
M3/s, M3/h, l/s, l/min, l/h
3. Units

Power Units: thermal power through the valve. kBTU/h

W, kW, BTU/h, Ton
Energy kBTU
J, kWh, MWh, kBTU, Ton H, MJ,
GJ
Installation Position Identify the installed water service location of the valve and its embedded Valve in Return Pipe
temperature sensor, or piped in series with the valve (T2). The sensor w/ Valve in Supply Pipe
longer cable is remote (T1) and will be assigned opposite the water service
of the valve.
Cable Length Remote Cable length selection (for proper operation do not cut cables). Remote 1/2” - 2” models
Temp Sensor sensor cable length settings adjusts wire resistance to accurately calculate 9.8ft. [3 M]

Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

4. Application

thermal power and energy. 4.9 ft. [1.5M]

2 1/2” - 6” models
32.8 ft. [10 M]
16.4 ft. [5 M]
9.8 ft. [3 M]
4.9 ft. [1.5 M]
Media Water or water/glycol composition used to accurately calculate: flow, Water
thermal power and energy. Monoethylene Glycol
Polyethylene Glycol

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

34
 Energy Valve
Cloud Settings

Web View Settings Continued

TAB SETTING FUNCTION DEFAULT / RANGE

Feedback Actuator analog feedback signal output on wire #5 u-signal. Flow
Power, T supply
T return, delta T
Valve position
Range Actuator analog feedback linear signal range. 2-10 V
0.5-10 V
0-10 V
5. Analog Feedback

Maximum Setting to equate 10 VDC or maximum feedback information. Setting must Flow
match the DDC range maximum setting. The grey box is an entry field and 0 to V’Nom
not the actual measured feedback and will hold the last value entered in it. Position
The factory setting on this is 0. 0 to 100%
(0-90 deg.)
Temperature
32°F to 212°F
0°C to 100°C
Power
0 to P’nom
Override functions Override functions to move the valve to a particluar point or position which
can be used for testing and commissoning purposes. All engaged overrides
stop and go back to normal operation automatically after two hours.
Auto Normal operation no override. Auto
Close Moves actuator to close valve. N/A
Open Moves actuator to open valve. N/A
6. Override

V’nom In flow control moves the actuator to full open position. N/A
V’max In fow control moves the actuator to V’max setting. N/A
Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

Motor Stop Stops the valve at current position. N/A

P’Nom In power control mode moves the actautor to P’nom position (full open). N/A
P’max In Power control mode moves the actautor to P’max setting. N/A
Simulated operation Engages simulation of flow and temperature that can be viewed on the N/A
overview page.
Setpoint Source Defines how the BMS valve set point is sent to the acuator either analog Analog
on wire 3 or via BACnet, Modbus or MP). Bus (BACnet, Modbus, MP)
Control Mode Controlled variable assigned to the actuator analog input y-signal, wire # 3. Flow Control
7. Control Settings

Power Control
Position Control
Invert Signal “No” valve modulates open when 10 VDC is received. “Yes” 10 VDC signal No
closes the valve. Yes
Signal Characteristic Setting when Controls modes are set to Flow or Position Equal Percentage
• Equal Percentage flow yields coil thermal power roughly Equal to the Linear
control signal.
• “linear” 50% controller command yields 50% flow output or position.
Vmax Used with Flow Control mode, this is the maximum flow setting of the valve V’Nom
and Limitation
8. Maximum

with a full flow output from the controller.

Vmin Used with Flow Control mode, this is the minimum flow setting of the valve 30% - 100% of V’nom
to maintain a minumum flow rate for particualar applications. Defined by size in Webview

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

35
Energy Valve
Cloud Settings

Web View Settings Continued

TAB SETTING FUNCTION DEFAULT / RANGE

Delta T Limiting Setting to disabled or enabled with limiting logic: dT Manger or dT Manager Disabled = “-“
Function Scaling. Both use settings“Delta T Limiting Value” but only dT Manager dT Manager
Scaling uses the “Flow Saturation Value. dT Manager Scaling
Delta T Limiting Value Low limit parameter for dT setpoint: 10°F
• For dT Manger this is the dT setpoint. 2°F to100°F
• For dT Manager Scaling this will reset so the dT setpoint is scaled, or 1.1°C to 55.5°C
variable. Default >30% of V’max
9. Delta T Manager

Option >10% of V’nom

The Data Analysis Tool may be used to help determine this value.
The grey box is an entry field and not the actual measured Delta T and will
hold the last value that is entered in it.
Flow Saturation Value Parameter used with dT Manager Scaling to reset the Delta T Limiting Value. (User defined)
When dT Manager Scaling is active: >30%-100% of V’max
• If actual flow is less than this parameter the dT setpoint will be reset
below the Delta T Limiting Value.
• If actual flow is equal to this parameter the dT setpoint will be equal to
Delta T Limiting Value.
• If actual flow is greater than this parameter the dT setpoint will be reset
above the Delta T Limiting Value.
The Data Analysis Tool may be used to help determine this value.

Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

36
 Operating Instructions
ZTH US

The ZTH US is a tool created to easily adapt the

flow settings of the Energy Valve in the field. It
directly connects to the Belimo actuator.

CONNECTION PROCESS:

Technical Information
Supply 24 VAC/DC
Communication PP
Used with actuator types LR, NR, AR, GR, AKR, GKR, EV,
AVK

LR, NR, AR, GR, AKR, GKR, EV, AVK Series

Use the interface on the top of the actuator.
Quarter turn to lock in place. Connect the
other end of the cable into the ZTH US. The
actuator must be powered for the ZTH US
to function.(Leave all of the wires of the
Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

actuator installed.)

RE-PROGRAMMING PROCESS:

Initial Screen Screen 1

When connected the display will show “Startup Progress” this Start Energy Valve process by pressing the down arrow.
process will take approximately 30 seconds. The first screen displays setpoint relative in % (SpRel).
Press the down arrow to advance.

Startup Progress SpRel

50%

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

37
Operating Instructions
ZTH US

ZTH US SETTINGS
Move through the displays. The chart below shows the complete list.
Setting Description Range and UOM Capability
SpRel Analog Input signal as a % of full signal 0 – 100% Read Only
RelPos Valve position as a % of full opening 0 – 100% Read Only
RelFlow Current flow as % of V’max 0 – 100% Read Only
AbsFlow Flow in GPM GPM Read Only
T1 remote Temperature opposite valve side F Read Only
T2 embedded Temperature at valve F Read Only
DeltaT Supply and return temperature differential F Read Only
RelPower Current power as % of P’max % Read Only
Abs power Current power output KBTU/hr Read Only
Cooling Energy Total cooling power since last reset KBTU Read Only
Heating Energy Total heating power since last reset KBTU Read Only
Override 1=Auto, 6=MotorStop, 1-9 Write Only
2=Close, 7=P’nom,
3=Open, 8=P’max,
4=V’nom, 9=Set Point Position Override
5=V’max,
SpPos Override 0 – 100% Write Only
Mode (0 = 0.5 – 10 V, 1= 2 – 10 V) 0-1 Write Only
ModeY Inv (0 = not inverted, 1= inverted) 0-1 Write Only
V’max Can be a percentage or flow. 30 – 100% Write Only
0 – 1000GPM
P’max Can be a percentage or power 1 – 100% Write Only
1 – 15000KBTU/hr

Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

Control Mode 0=Position Control, 0-2 Write Only
1=Flow Control,
2=Power Control
Install Pos 0= Return Flow, 0-1 Write Only
1= Supply Flow
IP-Address Valve IP on LAN Read Only
DeltaT Limit 0 = Disabled, 0-2 Write Only
1 = dT-Manager,
2 = dT-Manager Scaling
SpDeltaT Delta T Limiting Valve 2 – 100 F Write Only
SpFlowDeltaT Flow Saturation Value 0 – 1000 GPM Write Only
SensorStatus 0 = OK, 0-2 Read Only
1 = Not OK,
2 = OK Air bubbles
Glycol Concentration % Glycol concentration % reported by the 0-100% Read Only
Energy Valve only shown if activated

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

38
 Energy Valve

Actuator Adaptation
The actuator adaptation button calibrates the input signal range (2-10V)
to the actuator angle of rotation range by driving the actuator to the
mechanical end stops. Completion of the cycle, the actuator will follow
the current input signal. By default, the actuator will run the adaptation
cycle after the first power up. Belimo recommends performing a manual
adaptation to the actuator if the actuator has been replaced. The manual
adaptation can be activated by pressing the translucent “Adaptation” LED
button for three seconds.

Belimo Data Analysis Tool

Data Analysis Tool is used to analyze imported data from the “Web View Data Logging”. The Data Analysis Tool can be
downloaded from the Energy Valve web page (www. energyvalve.com).
• View power and delta T curves for different flows for a coil.
• View and diagnose system behavior based on delta T, flow, and power data collected for 13 months.
• Help in the continuous commissioning of the Energy Valve. It does this by suggesting optimized delta T and flow saturation
set points to be configured in the Energy Valve.

Compatibility:
The Data Analysis Tool runs with Microsoft Excel. There are two versions of the data analysis tool available. Please select the
Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

correct version to match the version of Excel you are running.

• Data analysis tool 2003 version; to be used with Microsoft Excel 2003 only.
• Data analysis tool 2007_2010 version; to be used with Microsoft Excel 2007 and 2010.

Constant Commissioning of the Energy Valve:

This tool can be used to constantly commission the Energy Valve.
Note: Keep a record of settings changes with date and time. This data can serve as a coil performance or maintenance record.

To use the Data Analysis Tool, the Energy Valve needs to collect data for a period that will represent full or close to full coil
saturation. Use the following steps to import the data into the tool:
A. Download the coil data (CSV files) from the Energy Valve’s Web View to your computer.
B. Import the .csv files in to the Data Analysis Tool. Multiple files can be imported at once.
C. Select the Delta T Determination tab. Then, click the Calculate button to determine the optimized Delta T and Flow Saturation
set points if the coil data shows close to saturation.
D. Log onto the Energy Valve Web View. Enter the delta T Setpoint (Delta T Limit Value) and Flow Saturation (Flow Saturation
Limit Value) set points in the Web View Setting page.
Belimo recommends performing this commissioning at least once annually to maximize system energy efficiency.

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

39
Energy Valve
Data Analysis Tool

Downloading Coil Data from Web View

• Select time frame for exporting data
• Short Term data is captured every 30 seconds.
• Long Term data is captured for a period of 15 minutes
and up to 2 hours.
• Data can be directly imported into data analysis tool. Files export
in .csv format.

Delta T Determination

Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

A. Click to import Data Logging files generated by the Energy Valve Web View.
B. Click to calculate the optimum delta T and flow saturation for the coil.
C. Delta T Setpoint and Flow Saturation are calculated based on the provided data. These values are then entered
into the Energy Valve Web View Settings area. The new settings will provide optimized delta T performance.
D. Flow saturation point.

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

40
 Energy Valve
Troubleshooting

Problem Field Observations Possible Solution

Actuator will not move. Actuator green LED is not on or flashing. Verify the power supply and control signal are
wired and operating correctly. If the actuator
wiring is correct and the Green LED is not
blinking the actuator has failed.
Note: the LED is solid green while booting up.
Actuator green LED is flashing but the valve will Valve may have debris.
not move. Depress the black gear release button on the
side of the actuator and use the override handle
to clear any debris that may have clogged the
valve. If the valve does not move, then remove
the actuator from valve and try to manually
operate the valve stem.
Actuator does not modulate with the control Valve throttles to either full open or closed. Verify the hydronic circuit is filled, water is
signal as expected. flowing, and isolation valves are opened. When
Mode of Control is set to Flow or Power, any
control signal greater than 0.5 or 2 VDC means
there is a flow command. The flow or power
logic will open the valve to satisfy the demand.
Delta T Manager may be active.
Valve is yielding low flow but cannot be Valve is partially open but will not move to a full If the Delta T Manager is enabled it may be
commanded to the full flow setting. open position with a full signal command. regulating the ∆T. Disable Delta T Manager until
the chiller or boiler is operating correctly.
Flow is lower than expected. Example: 50% flow signal is yielding 20% flow. If equal percentage is the setting for the Control
Signal Characteristic this is normal. For a
correlation between flow and input signal, see
the Equal Percentage Flow table on page 41.
Requested flow cannot be reached; actual Valve is full open. If the valve is fully open and flow feedback
flow is lower than commanded flow. is 5% lower than flow set point this event is
captured in the Status Summary in Web View.
Increase the pump differential pressure to
resolve low flow problems.
Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

Flow measurements are not stable. Air may be in the system. Check for air in the system. Remove air from
the system to solve the problem.
Flow Control, Power Control, and dT Manager Flow calculation is 0 GPM. See any flow error listed on the Status area of
Scaling are not working. the Web View or use the ZTH US.
Temperature sensor does not work. Web View Indication: Remove remote sensor wires from the terminals
-15°F > Temp. > 300°F and verify resistance with an ohm meter, replace
-26°C > Temp. > 149°C if damaged. Below are typical PT 1000 readings:
176°F [80°C] = 1347 ohms
68°F [20°C] = 1078 ohms
50°F [10°C] = 1039 ohms
ZTH: Sensor status not OK Web View status page: Check flow sensor to see if it is reading flow
Flow Sensor Error Counter > 0 when valve is open.
If it is not, contact Technical Support.
Device running slow when viewed in BACnet Device busy or slow. Reduce the number of points being pulled in
front end. BACnet system and or reduce the polling rate.
Valve does not respond to analog control signal. 2-10 analog signal is modulated but the actuator Once Object SpRel has been written to via
does not respond. BACnet the valve will no longer respond to
analog signal. The only way to restore the valve
responding to the analog control signal is to
power cycle the actuator.
Flow Sensor does not work properly. For 2½” through 6” - Flow sensor reading is Replace sensor.
below 3mA or higher than 20.5mA.
For ½”through 2” - Error byte communicates
failure status.
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

41
EV... Series Energy Valve
Stainless Steel Ball, NPT Female Ends
Application
Water-side control of heating and cooling systems for AHUs and water coils.
Equal Percentage / Linear: heating / cooling applications.

Mode of Operation
The Energy Valve is an energy metering pressure independent control valve
that optimizes, documents and proves water coil performance.

From Production Date

Product Features
EV The Energy Valve measures energy using its built-in electronic flow sensor
and supply and return temperature sensors. Controls power with its Power
Valve Specifications Control logic providing linear heat transfer regardless of temperature
Service chilled or hot water, 60% glycol max (open and pressure variations. Manages Low Delta T Syndrome with its built in
loop/steam not allowed) Delta T Manager. Measures glycol with advanced algorithms in its built in
Flow characteristic equal percentage/linear flow sensor. An IoT device utilizing cloud-based technology to optimize
Size ½”, ¾”, 1”, 1¼”, 1½”, 2” performance.
Type of end fitting NPT female ends
Materials
Body Dimensions
Valve forged brass, nickel plated E F A

EV_Dim
Sensor housing forged brass, nickel plated
Ball stainless steel
Stem stainless steel
Seat Teflon® PTFE C D
Characterizing disc Tefzel®
O-ring EPDM
Packing EPDM
Body pressure rating 360 psi
Media temperature range 14°F to 250°F [-10°C to +120°C]
39°F to 250°F [4°C to 120°C]** B

Maximum sound level <35 dB(A) I I

Leakage 0% G G

Close-off pressure 200 psi

Differential pressure range(∆P) 1 to 50 psi*, 5 to 50 psi, 8 to 50 psi** Valve
Inlet length required to meet Nominal Size Dimensions (Inches [mm])
specified measurement accuracy 5x nominal pipe size (NPS) DN
Humidity <95% RH non-condensing In. A B C D E F G I
[mm]
Flow metering technology ultrasonic with temperature and glycol 14.64" 7.50" 6.85" 6.29" 1.55" 1.55" 2.05” 3.15”

Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

½” 15
compensation [372] [191] [174] [160] [39] [39] [52] [80.1]
Flow control tolerance ±5% 14.92" 8.00" 7.02" 6.37" 1.55” 1.55” 2.25” 3.15”
¾” 20
Flow measurement tolerance ±2% [379] [203] [178] [162] [39] [39] [57] [80.1]
Flow measurement repeatability ±0.5% 15.43" 9.1" 7.29" 6.49" 1.55” 1.55” 2.50” 3.23”
1” 25 [165] [39] [39] [64] [82]
Glycol Monitoring Tolerance ±5% [392] [231] [185]
Temperature sensors PT1000 insertion sensors w/NPT pipe body 16.45" 10.00" 7.54" 6.61" 1.73" 1.73" 2.77” 3.39”
1¼” 32
Remote temperature sensor length 2 ft. 7.5 in. [0.8 m] short, 9.8 ft. [3 m] long [418] [254] [192] [168] [44] [44] [70.5] [86]
16.84" 10.78" 7.87" 6.77" 1.73” 1.73” 2.77” 3.70”
Temperature measurement According to PT1000 DIN EN60751 Class B. 1½” 40
[428] [274] [200] [172] [44] [44] [70.5] [94]
tolerance
Resolution of temperature 0.18°F (0.1°C) 17.12” 11.18” 8.26” 6.96 1.73” 1.73” 3.15” 4.13”
2” 50 [177] [44] [44] [80.1] [105]
[435] [284] [210]
sensor
Rated impulse voltage actuator/sensor: 0.8 kV (in accordance with Valve Nominal Type Actuator
EN 60730-1) Size Type
Flow Sensor Enclosure NEMA 1, IP54, UL enclosure type 1
Design Inches DN 2-way Non-Spring Electronic
Quality standard ISO 9001 Flow [mm] Female NPT Return Fail-Safe
Agency listings UL 60730-1/2-14, 2-18, CE according to Range
2004/108/EC and 2006/95/EC GPM
All flow tolerances are @ 68°F (20°C) & water.
*See flow reduction chart on page 43. 1.65-5.5 ½ 15 EV050S-5.5 LRB, LRX AKRB, AKRX
** Applies to 2” EV model EV200S-1000 only.
3.1-10.3 ¾ 20 EV075S-10.3 LRB, LRX AKRB, AKRX
Valve Nominal Size Weights
5.5-18.2 1 25 EV100S-18.2 LRB, LRX AKRB, AKRX
Inches DN [mm] Pounds [kg]
½” 15 5 [2.2] 8.6-28.5 1¼ 32 EV125S-28.5 NRB, NRX AKRB, AKRX
¾” 20 5.5 [2.5] 11.9-39.6 1½ 40 EV150S-39.6 NRB, NRX AKRB, AKRX
1” 25 6.5 [2.9]
1¼” 32 8.5 [3.8] 22.8-76.1 2 50 EV200S-76.1 ARB, ARX AKRB, AKRX
1½” 40 10 [4.5] 30-100 2 50 EV200S-1000 ARB, ARX AKRB, AKRX
2” 50 13.5 [6]

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

42
 EV... Series Energy Valve
Stainless Steel Ball, ANSI 125 Flange

Application
Water-side control of heating and cooling systems for AHUs and water coils.
Equal Percentage / Linear: heating / cooling applications.

From Production Date

EV Mode of Operation
The Energy Valve is an energy metering pressure independent control valve
that optimizes, documents and proves water coil performance.
Valve Specifications
Service chilled or hot water, 60% glycol max (open Product Features
loop/steam not allowed) The Energy Valve measures energy using its built-in electronic flow sensor
Flow characteristic equal percentage/linear and supply and return temperature sensors. Controls power with its Power
Size 2½”, 3”, 4”, 5”, 6” Control logic providing linear heat transfer regardless of temperature and
Type of end fitting pattern to mate with ANSI 125 flange
pressure variations. Manages Low Delta T Syndrome with its built in Delta
Materials
T Manager. An IoT device utilizing cloud-based technology to optimize
Body
performance.
Valve cast iron - GG25
Sensor housing ductile iron - GGG50
Ball stainless steel
Seat PTFE
Characterizing disc stainless steel Dimensions
Packing 2 EPDM O-rings, lubricated

D1341
Body pressure rating according to ANSI 125, standard class B H2 E F
Media temperature range 14°F to 250°F [-10°C to +120°C] H1
Maximum sound level 70 dBA
Conductivity of media min. 20uS/cm

D
Leakage 0%

I
Close-off pressure 100 psi

C
Differential pressure range(∆P) 1 to 50 psi*, 5 to 50 psi
Inlet length required to meet
specified measurement accuracy 5x nominal pipe size (NPS) B

G
Humidity <95% RH non-condensing A
Valve
Flow metering technology electromagnetic Nominal Size Dimensions (Inches [mm])GRB24-EV, GRX24-EV
ARB24-EV, ARX24-EV,
Flow control tolerance ±5% DN
Flow measurement tolerance ±2% In. A B C D E F G I
[mm]
Flow measurement repeatability ±0.5% 17.9” 17.9” 11.2” 7.9” 3.64” 3.64” 5.50” 0.75”
Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

2½” 65 [201] [92] [92] [140] [19]

Temperature sensors 32.8 ft. [10m] [454] [454] [284]
PT1000 insertion senors 19.7” 19.7” 11.8” 7.9” 3.94” 3.94” 6.07” 0.75”
3” 80
Thermal well ½ NPT [499] [499] [300] [201] [100] [100] [154] [19]
Remote temperature sensor length 22.85” 22.85” 12.8” 8.3” 3.75” 3.75” 7.50” 0.75”
4” 100 [211] [95] [95] [190.5] [19]
Standard 32.8 ft. [10 m] [581] [581] [325]
Optional 4.9 ft. [1.5m], 9.8 ft. [3m], 16.4 ft. [5m] 25.18” 25.18” 14.4” 9.4” 5” 5” 8.50” 0.88”
5” 125
Temperature measurement According to PT1000 DIN EN60751 Class B. [640] [640] [366] [239] [127] [127] [215.9] [22]
tolerance 30.2” 30.2” 15.4” 10.4” 5.5” 5.5” 9.50” 0.88”
6” 150
Resolution of temperature 0.18°F (0.1°C) [767] [767] [391] [264] [140] [140] [241.3] [22]
sensor
Rated impulse voltage actuator/sensor: 0.8 kV (in accordance with
EN 60730-1)
Flow sensor enclosure NEMA 1, IP54, UL enclosure type 1 Available Flow Rates
Quality standard ISO 9001
Agency listings UL 60730-1/2-14, 2-18, CE according to Valve Nominal Type Actuator
2004/108/EC and 2006/95/EC Size Type
All flow tolerances are @ 68°F (20°C) & water.
* See flow reduction table on page 43. Design
Flow DN 2-way Non-Spring Electronic
Inches
Range [mm] Flanged Return Fail-Safe
Valve Nominal Size Weights GPM
Inches DN [mm] Pounds [kg]
38-127 2½ 65 EV250S-127 ARB, ARX AKRB, AKRX
2½” 65 52 [23.6]
3” 80 63 [28.7] 54-180 3 80 EV300S-180 ARB, ARX AKRB, AKRX
4” 100 89 [40.5]
95-317 4 100 EV400S-317 GRB, GRX AKRB, AKRX
5” 125 120 [54.7]
6” 150 154 [70.0] 149-495 5 125 EV500S-495 GRB, GRX GKRB, GKRX
214-713 6 150 EV600S-713 GRB, GRX GKRB, GKRX

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

43
EV... Series Energy Valve
Stainless Steel Plug and Seat, ANSI 250 Flange

Application
Water-side control of heating and cooling systems for AHUs and water coils.
Equal Percentage / Linear: heating / cooling applications.

Mode of Operation

From Production Date

The Energy Valve is an energy metering pressure independent control valve
EV that optimizes, documents and proves water coil performance.

Product Features
Valve Specifications The Energy Valve measures energy using its built-in electronic flow sensor
Service chilled or hot water, 60% glycol max (open and supply and return temperature sensors. Controls power with its Power
loop/steam not allowed) Control logic providing linear heat transfer regardless of temperature and
Flow characteristic equal percentage/linear pressure variations. Manages Low Delta T Syndrome with its built in Delta
Size 2½”, 3”, 4”, 5”, 6” T Manager. An IoT device utilizing cloud-based technology to optimize
Type of end fitting pattern to mate with ANSI 250 flange performance.
Materials
Body cast iron
Stem stainless steel
Sensor housing ductile iron GGG50 Dimensions
Seat and Plug stainless steel E F
Packing NLP (no lip packing)
Body pressure rating according to ANSI 250, standard class B
Media temperature range 14°F to 250°F [-10°C to +120°C]
Maximum sound level 70 dBA
D
Conductivity of media min. 20uS/cm
C
Leakage ANSI Class IV
Differential pressure range(∆P) 7.5 to 50 psid or 1 to 50 psid with flow
reductions
Maximum inlet pressure (water) 300 psi
Maximum differential pressure 50 psi
Inlet length required to meet 5x nominal pipe size (NPS)
specified measurement accuracy
Humidity <95% RH non-condensing A, B
Flow metering technology electromagnetic
Flow control tolerance ±5% Valve
Flow measurement tolerance ±2% Nominal Size Dimensions (Inches [mm])

Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

Flow measurement repeatability ±0.5% DN
Inches A B C D E F
Temperature sensors PT1000 insertion senors with thermal well [mm]
22.2” 22.2” 20.4” 18.25” 4.5” 4.5”
Remote temperature sensor length 2½” 65
[564] [564] [516] [464] [114] [114]
Standard 32.8 ft. [10 m]
23.81” 23.81” 20.99” 19.18” 4.5” 4.5”
Optional 4.9 ft. [1.5m], 9.8 ft. [3m], 16.4 ft. [5m] 3” 80
[605] [605] [533] [487] [114] [114]
Temperature measurement According to PT1000 DIN EN60751 Class B
28.27” 28.27” 22.73” 20.37” 4.5” 4.5”
tolerance 4” 100
[718.1] [718.1] [577.3] [517] [114] [114]
Resolution of temperature 0.18°F (0.1°C)
31.5” 31.5” 20.99” 20.87” 4.5” 4.5”
sensor 5” 125
[800] [800] [533] [530] [114] [114]
Rated impulse voltage actuator/sensor: 0.8 kV (in accordance with
36.37” 36.37” 25.12” 21.25” 4.5” 4.5”
EN 60730-1) 6” 150
[924] [924] [638] [540] [114] [114]
Flow sensor enclosure NEMA 1, IP54, UL enclosure type 1
Quality standard ISO 9001
All flow tolerances are @ 68°F (20°C) & water. Available Flow Rates
* See flow reduction table on page 43. Valve Nominal
Type Actuator Type
Size
Close-off Pressures
Design
Flow DN Non-Spring Electronic
Valve Nominal Size Actuators Weights Inches 2-way Flanged
Range [mm] Return Fail-Safe
Inches DN [mm] EV AVK Pounds [kg] GPM
2½ 65 310 psi 310 psi 54 [24.5] 38-127 2½ 65 EV250S-127-250 EVX AVKX
3 80 310 psi 310 psi 63 [28.7] 54-180 3 80 EV300S-180-250 EVX AVKX
4 100 310 psi 290 psi 99 [44.9] 95-317 4 100 EV400S-317-250 EVX AVKX
5 125 296 psi 202 psi 126 [57.2] 149-495 5 125 EV500S-495-250 EVX AVKX
6 150 215 psi 135 psi 173 [78.5] 214-713 6 150 EV600S-713-250 EVX AVKX

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

44
 EV...Series Energy Valve
Non-Spring Return and Electronic Fail-Safe Actuator Series
Operation
The actuator is electronically protected against overload.
Wiring Diagrams
The actuators use a brushless DC motor, which is controlled by an
Application Specific Integrated Circuit (ASIC). The ASIC monitors and
controls the actuators rotation and provides a digital rotation sensing
(DRS) function to prevent damage to the actuator in a stall condition. A Actuators with appliance cables are numbered.
Power consumption is reduced in a holding mode.
2 CAUTION Equipment damage!
Add-on auxiliary switches or feedback potentiometers are easily fastened Actuators may be connected in parallel.
directly onto the actuator body for signaling and switching functions. Power consumption and input impedance must be observed.

Non-Spring Return LR, NR, GR, AR and Electronic 3 Actuators may also be powered by 24 VDC.
Fail-Safe Actuators AKR and GKR Actuators with plenum rated cable do not have numbers on
Actuator Specifications
18 wires; use color codes instead.
Power supply 24 VAC ± 20%
24 VDC ± 10%
Electric frequency 50/60 Hz
Meets cULus requirements without the need of an electrical
Power consumption ground connection
LR Series 4W
NR Series 5W WARNING Live Electrical Components!
GR Series 8W During installation, testing, servicing and troubleshooting of this
AR Series 5W (½” to 2”), 7W (2½” to 6”) product, it may be necessary to work with live electrical components. Have a
AKR Series 14W (½” to 2”), 16W (2½” to 6”) qualified licensed electrician or other individual who has been properly
GKR Series 17W trained in handling live electrical components perform these tasks. Failure to
follow all electrical safety precautions when exposed to live electrical
Transformer sizing
components could result in death or serious injury.
LR Series 7 VA (class 2 power source)
NR Series 8 VA (class 2 power source)
GR Series 12 VA (class 2 power source) 2 to 10 VDC Control
AR Series 8 VA (½” to 6”), 11 VA (2½” to 6”) (class 2 24 VAC Transformer A 2 3 18
power source) Line Blk (1) Common
T

AKR Series 23 VA (½” to 2”), 26VA (2½” to 6”) (class 2 Volts Red (2) Hot +

power source) Control Signal (-)

Cable 1
2 to 10 VDC (+)
GKR Series 29 VA (class 2 power source) Wht (3) Y-Input

(-)
Electrical connection 18 GA, plenum rated cable 2 to 10 VDC
Feedback Signal (+) Org (5) U-Output
½” conduit connector Pnk (6) C1 BACnet MS/TP -
protected NEMA 2 (IP54) 3 ft. [1 m] cable C1 Modbus RTU -
Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

Gry (7) C2 BACnet MS/TP +

Overload protection electronic throughout 0° to 90° rotation C2 Modbus RTU +

Cable T1
Wht (1) S
Operation range Y 2 to 10 VDC (default) VDC variable
T

Red (2) S1
Control modulating

Cable T2
Wht (1) S
Input impedance 100 kΩ (0.1 mA), 500Ω
T

Red (2) S2

Flow Feedback 2 to 10 VDC (default), VDC variable RJ-45

Ethernet
Communication BACnet IP, BACnet MS/TP, Listed by BTL, web BACnet IP
Modbus IP
server, Belimo MP-Bus
Direction of rotation motor electronically variable
2-10 VDC
fail-safe reversible with built-in switch
Manual override external push button
Running time normal operation 90 seconds FC FO
Running time fail-safe 35 seconds A – AB = 0% A – AB = 100%
Humidity 5 to 95% RH, non-condensing
POP POP
Ambient temperature -22°F to 122°F [-30°C to 50°C]
10% 90% 10% 90%
Storage temperature -40°F to 176°F [-40°C to 80°C] FO FC
FO FC
Housing NEMA 1, IP54, UL enclosure type 1
Noise level <45dB(A) at 90 seconds
Servicing maintenance free
Quality standard ISO 9001 Fail-Safe Power-Off Position, AKRB, AKRX, GKRB, GKRX
Agency listings UL 60730-1/2-14, 2-18, CE according to
2004/108/EC and 2006/95/EC
System Ground

The Energy Valve is based on Belimo patent and patent pending technology:
In cases where the valve body is electrically isolated from the water pipe, an
earth ground should be installed in order for the sensor to work properly.
•• US-Patent: 6,039,304: Ball valve with modified characteristics.
•• US-Patent Pending: 2011/0153089: HVAC actuator comprising a network interface, data
store and a processor.
•• US-Patent Pending: 2009/0009115: Control of sensor less and brushless DC-Motor.
The Energy Valve incorporates additional technology – Powered by Optimum Energy™.

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

45
EV...Series Energy Valve
Non-Spring Return and Electronic Fail-Safe Actuator Series
Operation
Wiring Diagrams
The actuator is electronically protected against overload.
The actuators use a brushless DC motor, which is controlled by an
Application Specific Integrated Circuit (ASIC). The ASIC monitors and
controls the actuators rotation and provides a digital rotation sensing A Actuators with appliance cables are numbered.
(DRS) function to prevent damage to the actuator in a stall condition. CAUTION Equipment damage!
2
Power consumption is reduced in a holding mode. Actuators may be connected in parallel.
Add-on auxiliary switches or feedback potentiometers are easily fastened Power consumption and input impedance must be observed.
directly onto the actuator body for signaling and switching functions. Actuators may also be powered by 24 VDC.
3
Non-Spring Return EV and
Actuators with plenum rated cable do not have numbers on
Electronic Fail-Safe Actuators AVK 18 wires; use color codes instead.
Actuator Specifications
Power supply 24 VAC ± 20%
24 VDC ± 10%
Meets cULus requirements without the need of an electrical
Electric frequency 50/60 Hz ground connection
Power consumption
EV Series 6 W running, 3.5 W holding WARNING Live Electrical Components!
AVK Series 12 W running, 3 W holding During installation, testing, servicing and troubleshooting of this
Transformer sizing product, it may be necessary to work with live electrical components. Have a
EV Series 7 VA (class 2 power source) qualified licensed electrician or other individual who has been properly
AVK Series 21 VA (class 2 power source) trained in handling live electrical components perform these tasks. Failure to
follow all electrical safety precautions when exposed to live electrical
Electrical connection 18 GA, plenum rated cable
components could result in death or serious injury.
½” conduit connector
protected NEMA 2 (IP54) 3 ft. [1 m] cable
Overload protection electronic throughout full stroke 2 to 10 VDC Control
Electrical Protection actuators are double insulated 24 VAC Transformer A 2 3 18
Operation range Y 2 to 10 VDC (default), variable VDC Line Blk (1) Common
T

Control modulating Volts Red (2) Hot +

Input impedance 100 kΩ (0.1 mA) for 2-10 VDC, 500Ω for Control Signal (-)

Cable 1
2 to 10 VDC (+)
4 to 20 mA Wht (3) Y-Input

(-)
Feedback output U 2 to 10 VDC 2 to 10 VDC
Feedback Signal (+) Org (5) U-Output

Stroke Pnk (6) C1 BACnet MS/TP -

C1 Modbus RTU -
EV Series 2” [50 mm] Gry (7) C2 BACnet MS/TP +
C2 Modbus RTU +

AVK Series 1.25” [32 mm]

Cable T1
Wht (1) S T

Linear force Red (2) S1

Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

EV Series 562 lbf [2500 N]
Cable T2
Wht (1) S T

AVK Series 450 lbf [2000 N] Red (2) S2

Direction of rotation motor reversible with built-in switch RJ-45

Ethernet

BACnet IP

fail-safe reversible with switch Modbus IP

Position indication stroke indicator on bracket

Manual override 5 mm hex crank (3/16” Allen), supplied 2-10 VDC
Running time motor 90 seconds (default), variable (90 to 150 sec)
FC FO
fail-safe 35 seconds A – AB = 0% A – AB = 100%
Humidity 5 to 95% RH, non-condensing
Ambient temperature -22°F to 122°F [-30°C to 50°C]
Storage temperature -40°F to 176°F [-40°C to 80°C]
Housing NEMA 1, IP42, UL enclosure type 1 POP POP
Housing material aluminum die cast and plastic casing 90% 10% 90% 10%
Noise level <60 dB(A)
Servicing maintenance free
Quality standard ISO 9001
Fail-Safe Power-Off Position, AVKX
Weight
EV Series 9 lbs System Ground
AVK Series 15.9 lbs
In cases where the valve body is electrically isolated from the water pipe, an
Agency listings cULus acc. to UL60730-1A/-2-14, CAN/CSA
E60730-1:02, CE acc. to 2004/108/EC and earth ground should be installed in order for the sensor to work properly.
2006/95/EC
Bridging time (AVK Series) 2 second delay before fail-safe activates
Pre-charging time (AVK Series) 5 to 20 seconds Use flexible metal conduit. Push the Listed conduit fitting device over the actuator’s cable to butt against
the enclosure. Screw in conduit connector. Jacket the actuators input wiring with Listed flexible conduit.
The Energy Valve is based on Belimo patent and patent pending technology, US-Patent 6,039,304: Ball valve Properly terminate the conduit in a suitable junction box. Rated impulse Voltage 800V. Type of action 1.
with modified characteristics. US-Patent Pending: 2011/0153089: HVAC actuator comprising a network Control Pollution Degree 3.
interface, data store and a processor. US-Patent Pending: 2009/009115: Control of sensor less and brushless In cases where the valve body is electrically isolated from the water pipe, an earth ground should be
DC-Motor. The Energy Valve incorporates additional technology - Powered by Optimum EnergyTM. installed in order for the sensor to work properly. Earth ground can be connected directly on the sensor
body. A connection point is provided on the flange of the sensor body.

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

46
 Energy Valve
Flow Pressure Characteristics

Flow Reduction Chart

MAXIMUM FLOW BASED ON MINIMUM DIFFERENTIAL PRESSURE FOR ANSI 125 NPT MODELS
Size
8 psi 5 psi* 4 psi 3 psi 2 psi 1 psi
Inches DN [mm]
½ 15 5.5 GPM 5.5 GPM 5.5 GPM 5.5 GPM 4.8 GPM 3.4 GPM
¾ 20 10.3 GPM 10.3 GPM 10.3 GPM 9.9 GPM 8.1 GPM 5.7 GPM
1 25 18.2 GPM 18.2 GPM 18.2 GPM 17.2 GPM 14.1 GPM 9.9 GPM
1¼ 32 28.5 GPM 28.5 GPM 28.5 GPM 28.5 GPM 23.3 GPM 16.5 GPM
1½ 40 39.6 GPM 39.6 GPM 39.6 GPM 39.6 GPM 34.9 GPM 24.7 GPM
2 50 100 GPM** 76.1 GPM 74 GPM 64.1 GPM 52.3 GPM 37 GPM
2½ 65 127 GPM 127 GPM 93 GPM 81 GPM 66 GPM 47 GPM
3 80 180 GPM 180 GPM 138 GPM 120 GPM 97 GPM 69 GPM
4 100 317 GPM 317 GPM 235 GPM 203 GPM 166 GPM 117 GPM
5 125 495 GPM 495 GPM 367 GPM 318 GPM 260 GPM 183 GPM
6 150 713 GPM 713 GPM 550 GPM 476 GPM 389 GPM 275 GPM

* Select valve based on a minimum of 5 PSI differential.

** Applies to 2” EPIV models P2200S-800 through P2200S-1000 only.

MAXIMUM FLOW BASED ON MINIMUM DIFFERENTIAL PRESSURE FOR ANSI 250 FLANGED MODELS
Size
7.5 psi*** 5 psi 4 psi 3 psi 2 psi 1 psi
Inches DN [mm]
2½ 65 127 GPM 109 GPM 98 GPM 85 GPM 69 GPM 49 GPM
3 80 180 GPM 153 GPM 137 GPM 118 GPM 97 GPM 68 GPM
4 100 317 GPM 280 GPM 251 GPM 217 GPM 177 GPM 125 GPM
5 125 495 GPM 436 GPM 390 GPM 337 GPM 275 GPM 195 GPM
6 150 713 GPM 593 GPM 531 GPM 460 GPM 375 GPM 265 GPM
Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

*** Select valve based on a minimum of 7.5 PSI differential.

Input Signal Scaling

FLOW CONTROL: EQUAL PERCENTAGE FLOW RESPONSE POWER CONTROL: LINEAR POWER RESPONSE OR FLOW CONTROL:
TO INPUT SIGNAL (Y) LINEAR FLOW RESPONSE TO INPUT SIGNAL (Y)
0.5-10 VDC Signal 2-10 VDC Signal Water Flow in % of V’max Power in % of P’max
0.5-10 VDC Signal 2-10 VDC Signal or Water Flow in %
0.5 2 0%
of V’max
3.16 4.24 10%
0.5 2 0%
5.25 6 20%
1.45 2.8 10%
6.49 7.04 30%
2.40 3.60 20%
7.29 7.72 40%
3.35 4.40 30%
7.95 8.28 50%
4.30 5.20 40%
8.48 8.72 60%
5.25 6 50%
8.96 9.12 70%
6.20 6.80 60%
9.34 9.44 80%
7.15 7.60 70%
9.66 9.73 90%
8.10 8.40 80%
10 10 100%
9.05 9.20 90%
10 10 100%

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

47
Energy Valve
BACnet
BACnet Protocol Implementation Conformance Statement
Date: February 24, 2017
Vendor ID: 423
Vendor Name: BELIMO Automation AG
Product Name: P..W..EV-BAC
Product Model Number: N/A
Application Software Version: 3.01-0000 Firmware Revision: 12.25 BACnet Protocol Revision: 1.12
Product Description:
The device is an electronic pressure independent characterized control valve (CCV) with adjustable flow rate, sensor-operated flow control and
monitoring of power and energy. The set-point, configuration parameters and feedback values are communicated via BACnet/IP or BACnet MS/TP.
The commissioning of the device (BACnet Device Address, IP Address settings, Foreign Device settings, MS/TP) is done via the integrated web-server.

BACnet Standardized Device Profile (Annex L):

þ BACnet Application Specific Controller (B-ASC)

List all BACnet Interoperability Building Blocks Supported (Annex K): Data Sharing - ReadProperty-B (DS-RP-B)
Data Sharing - ReadPropertyMultiple-B (DS-RPM-B)
Data Sharing - ReadProperty-B (DS-RP-B)
Data Sharing - WriteProperty-B (DS-WP-B)
Data Sharing - COV-B (DS-COV-B)
Device Management - DynamicDeviceBinding-B (DM-DDB-B)
Device Management - DynamicObjectBinding-B (DM-DOB-B)
Device Management - DeviceCommunicationControl-B (DM-DCC-B)

Segmentation Capability:þ No
Standard Object Types Supported:

BACnet Protocol Implementation Conformance Statement Continued

Data Link Layer Options:
þ BACnet IP, (Annex J)

Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

þ BACnet IP, (Annex J), Foreign Device
þ MS/TP master (Clause 9), baud rate(s): 115K,76.8K, 38.4K,19.2K,9.6K
Device Address Binding:
Is static device binding supported? (This is currently necessary for two-way communication with MS/TP slaves and certain other devices.)
o Yes þ No
Networking Options:
o BACnet/IP Broadcast Management Device (BBMD)

Character Sets Supported:

þ ISO 10646 (UTF-8)

1
Only if object commandable
• The properties Object_Name and Location of the Device Object support up to 255 characters (all other character strings are read-only).
• The device does not support the CreateObject and DeleteObject service.
• The writable Present_Value of Value objects may be changed in different ways: web page, service tool and BACnet service.
The value stored in the Present_Value represents the last value written via BACnet and doesn't reflect the actual setting in use.
Service processing
• The device supports DeviceCommunicationControl service. No password is required.

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

48
 Energy Valve
BACnet Object Description List

Object Name Object Type /Instance Description Values Default Capability

Device_Name Device [x]
Setpoint Source The actutaor has the possibility
to be controlled from an analog input and at
the same time being intergrated in BACnet
SpSource Multi-state Value [122] (for monitoring). Depending on this setting Analog Bus Analog Read/Write
the setpoint by bus or analog is valid. Analog:
Setpoint from analog signal 0.5...10V on wire
3. Bus: Setpoint from BACnet AO [1]
1- Auto
2- Close
3- Open
4- V'nom
Override Multi-state Output [1] Override Control Auto Read/Write
5- V'max
6- MotStop
7- P'nom
8- P'max
RelPos Analog Input [1] Relative Postion in % 0…100 - Read Only
Glycol Concentration in % . If measurement is
GlycolConcentr Analog Input [60] 0…100 - Read Only
locked will display a constant value -1
AbsPos Analog Input [2] Absolute Position in ° 0…90 - Read Only
No
SpPosReached Binary Input [1] Setpoint Position reached - Read Only
Yes
1- Not Selected
2- Standby
DeltaTMgrStatus Multi-state Input [102] Delta T Manager Status 3- Active - Read Only
4- Scaling standby
5- Scaling Active
RelFlow Analog Input [10] Relative Flow in % 0...100 - Read Only
AbsFlow_SI1 Analog Input [11] Absolute Flow in l/min 0...100,000 - Read Only
AbsFlow_SI2 Analog Input [12] Absolute Flow in m3/h 0...600 - Read Only
Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

AbsFlow_SI3 Analog Input [14] Absolute Flow in l/s 0...100,000 - Read Only
AbsFlow_SI4 Analog Input [15] Absolute Flow in l/h 0…100,000 - Read Only
AbsFlow_US Analog Input [13] Absolute Flow in gpm 0...100,000 - Read Only
SpAbsFlow_ls Analog Input [114] Setpoint Absolute Flow in l/s 0…100,000 - Read Only
SpAbsFlow_lmin Analog Input [111] Setpoint Absolute Flow in l/min 0…100,000 - Read Only
SpAbsFlow_lh Analog Input [115] Setpoint Absolute Flow in l/h 0…600 - Read Only
SpAbsFlow_m3h Analog Input [112] Setpoint Absolute Flow in m3/h 0…600 - Read Only
SpAbsFlow_gpm Analog Input [113] Setpoint Absolute Flow in gpm 0…100,000 - Read Only
SpAnalog_V Analog Input [5] Setpoint Analog in Volt 0…10.00 - Read Only
T1_SI Analog Input [20] Temperature 1 (remote) in °C -10...+120 - Read Only
T1_US Analog Input [25] Temperature 1 (remote) in °F 14...248 - Read Only
T2_SI Analog Input [21] Temperature 2 (embedded) in °C -10...+120 - Read Only
T2_US Analog Input [26] Temperature 2 (embedded) in °F 14...248 - Read Only
DeltaT_K Analog Input [22] Delta Temperature in K 0...+500 - Read Only
DeltaT_US Analog Input [27] Delta Temperature in °F -500...+500 - Read Only
RelPower Analog Input [40] Relative Power in % 0...300 - Read Only
AbsPower_SI Analog Input [30] Power in kW 0...2.147e+9 - Read Only
AbsPower_US1 Analog Input [35] Power in kBTU/h 0...2.147e+9 - Read Only

New Energy Valve 3 are in bold.

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

49
Energy Valve
BACnet Object Description List
Object Name Object Type /Instance Description Values Default Capability
AbsPower_US2 Analog Input [45] Power in RT 0...2.147e+9 - Read Only
E_Cooling_SI Analog Input [31] Cooling Energy in kWh 0...2.147e+9 - Read Only
E_Cooling_US1 Analog Input [36] Cooling Energy in kBTU 0...2.147e+9 - Read Only
E_Cooling_US2 Analog Input [46] Cooling Energy in ton.h 0...2.147e+9 - Read Only
E_Cooling_US3 Analog Input [33] Cooling Energy in MJ 0…2.147e+9 - Read Only
E_Heating_US3 Analog Input [34] Heating Energy in MJ 0…2.147e+9 - Read Only
E_Heating_SI Analog Input [32] Heating Energy in kWh 0...2.147e+9 - Read Only
E_Heating_US1 Analog Input [37] Heating Energy in kBTU 0...2.147e+9 - Read Only
E_Heating_US2 Analog Input [47] Heating Energy in ton.h 0...2.147e+9 - Read Only
Vmax Analog Value [100] Maximum Flow Limit in % 0...100 100 Write Only
Vmax_SI Analog Value [90] Maximum Flow Limit in l/min 0...4000 - Write Only
Vmax_US Analog Value [91] Maximum Flow Limit in gpm 0...1000 - Write Only
Vnom_SI Analog Value [101] Nominal Volume Flow in l/min (read-only) 0...100,000 - Read Only
Vnom_US Analog Value [102] Nominal Volume Flow in gpm (read-only) 0...100,000 - Read Only
Pmax Analog Value [105] Maximum Power Limit in % 0...100 100 Write Only
Pmax_SI Analog Value [95] Maximum Power Limit in kW 0...5000 - Write Only
Pmax_US Analog Value [96] Maximum Power Limit in kBTU/h 0...15,000 - Write Only
Pnom_SI Analog Value [106] Nominal Power Limit in kW (read-only) 0...2.147e+9 - Read Only
Pnom_US Analog Value [107] Nominal Power Limit in kBTU/h (read-only) 0...2.147e+9 - Read Only
Control Mode 1- PosCtrl
ControlMode Multi-state Value [100] The value defines the interpretation of 2- FlowCtrl FlowCtrl Read/Write
the setpoint. 3- PowerCtrl
1- Disabled
DeltaT_Limitation Multi-state Value [101] Delta T Limitation 2- dT-Manager Disabled Read/Write
3- dT-Mgr scaling
SpDeltaT_K Analog Value [103] Setpoint DeltaT in K 256...311 4 Write Only

Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

SpDeltaT_US Analog Value [104] Setpoint DeltaT in °F 2...100 7 Write Only
Setpoint Flow at DeltaT in l/min (Flow satura-
SpFlow_DeltaT_SI Analog Value [108] 0...4000 0 Write Only
tion value)
Setpoint Flow at DeltaT in gpm (Flow saturation
SpFlow_DeltaT_US Analog Value [109] 0...1000 0 Write Only
value)
ErrorState Analog Input [100] Error State see table below - Read Only
None
RstErrCount Binary Value [100] Reset Error Counters None Read/Write
Reset
Summary Status OK
SummaryStatus BI [101] - R
Summarizes all status from MI 103 - 107 Not OK
StatusSensor MI [103] Status Sensor OK - R
Indicates informations within the flow sensor Flow Sensor not OK
and both temperature sensors T1 not OK
T2 not OK
StatusFlow MI [104] Status Flow OK - R
Setpoint cannot be reached within 3 min during Reverse flow detected
flow control Flow not reached
Flow is measured but position of valve is closed Flow in closed position
Reverse flow is detected
StatusMedia MI [105] Status Media OK - R
Airbubbles in the hydronic system Airbubbles
Freeze warning

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

50
 Energy Valve
BACnet Object Description List

Object Name Object Type /Instance Description Values Default Capability

StatusActuator MI [106] Status Actuator OK - R
Mechanical overload due to blocked valve, etc. Actuator cannot move
Gear disengaged button pressed Gear disengaged
StatusPower MI [107] Status Power OK - R
Setpoint cannot be reached within 3 min during Power not reached
power control
Setpoint Relative in %
The set point is related either to the position,
SpRel Analog Output [1] 0…100 0 Read/Write
the flow (Vmax) or the power (Pmax).
See ControlMode for more information.

Error State Translation

Bit 0: (1) Error Sensor T1
Bit 1: (2) Error Sensor T2
Bit 2: (4) Error Flow Sensor
Bit 3: (8) Actuator cannot move
Bit 4: (16) Flow with closed valve
Bit 5: (32) Air bubbles
Bit 6: (64) Flow not reached
Bit 7: (128) Power not realized
Bit 8: (256) Gear disengaged
Bit 9: (512) Watchdog triggered

Example: “Flow not reached” + “Gear disengaged” = 64 + 256 = 320

Energy Valve -Modbus Description

Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

Modbus General Notes

General information Protocol: Modbus RTU / RS-485
Number of nodes: Max. 32 (without repeater)
Transmission formats: 1-8-N-2, 1-8-N-1, 1-8-E-1, 1-8-O-1, Default: 1-8-N-2
Baud rate: 9,600, 19,200, 38,400, 76,800, Default: 38,400 Baud 115,200
Baud
Terminating resistor: 120 Ω (to be done with external resistor)
Parameterization: through the integrated web server
Register implementation All data is arranged in a table and addressed by 1..n (register) or 0..n-1 (address). No
distinction is made between data types (Discrete Inputs, Coils, Input Registers and Holding
Registers). As a consequence, all data can be accessed with the two commands for Holding
Register. The commands for Discrete Inputs and Input Registers can be used as an alterna-
tive.
Standard commands Read Holding Registers [3]
Write Single Register [6]
Read Discrete Inputs [2]
Read Input Registers [4]
Write Multiple Registers [16]

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

51
Energy Valve
Modbus Description

Command “Read Discrete Inputs” The command reads one or more bits and can alternatively be used for Register No. 105
(Malfunction and Service information). Example: The start address to be used is
1664 104 (Register Address) * 16 (Bit) =1664
Interpret values in the registers All values in the register are unsigned integer with exception of Register No. 17/19/22.
Signed integers are represented as two’s complement.

Example unsigned integer: Read (Function 03, 1 Register) Value Register No. 12 =
0001’1010’1100’10002 = 6,85610
Actual Value = Value * Scaling factor * Unit = 6,856 * 0.01 * m3/h = 68.56 m3/h
Example signed integer Read (Function 03, 1 Register) Value Register No. 17 =
1111’1101’1111’00102 = -52610
Actual Value = Value * Scaling factor * Unit = -526 * 0.01 * °C = -5.26 °C
32-Bit Values in two registers Values that exceed 65,535 are stored in two consecutive Registers and have to be
interpreted as “little endian” / LSW (Least Significant Word) first.

Example: Register No. 10 (AbsFlow LowByte) = 14,55110 = 0011’1000’1101’01112

Register No. 11 (AbsFlow HighByte) = 1910 = 0000’0000’0001’00112
AbsFlow = 0000’0000’0001’0011’0011’1000’1101’01112 = 1,259,73510
= 1259.735 l/h
AbsFlow High Byte AbsFlow Low Byte
19 14,551
0000’0000’0001’0011 0011’1000’1101’0111
Math formula:
AbsFlow = ( AbsFlow HighByte * 65,536 ) + AbsFlow LowByte

Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

AbsFlow = ( 19 * 65,536 ) + 14,551 = 1,259,735 = 1259.735 l/h

Modbus Overview

Number Address Register R/W

1 0 Setpoint [%] R/W
2 1 Override control R/W
3 2 - R
4 3 Actuator type R
5 4 Relative position [%] R
6 5 Absolute position [ °] R
7 6 Relative Flow [%] R
8 7 Absolute flow [UnitSel] LData R
9 8 HData
10 9 Absolute flow [l/s] LData R
11 10 HData
12 11 Absolute flow [gpm] LData R
13 12 HData

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

52
 Energy Valve
Modbus Overview
Modbus Overview Continuation
Number Address Register R/W
14 13 Setpoint Absolute Flow [UnitSel] LData R
15 14 HData
16 15 Setpoint Analog [V] R
17 16 Temperature 1 [°C] R
18 17 Temperature 1 [°F] R
19 18 Temperature 2 [°C] R
20 19 Temperature 2 [°F] R
21 20 Delta Temperature [K] R
22 21 Delta Temperature [°F] R
23 22 Glycol Concentration [%] R
24 23 Relative power [%] R
25 24 Absolute Power [UnitSel] LData R
26 25 HData
27 26 Absolute Power [kW] LData R
28 27 HData
29 28 Absolute Power [kBTU/h] LData R
30 29 HData
31 30 Energy Cooling [UnitSel] LData R
32 31 HData
33 32 Energy Cooling [kWh] LData R
34 33 HData
35 34 Energy Cooling [kBTU] LData R
Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

36 35 HData
37 36 Energy Heating [UnitSel] LData R
38 37 HData
39 38 Energy Heating [kWh] LData R
40 39 HData
41 40 Energy Heating [kBTU] LData R
42 41 HData
101 100 Series number 1st part R
102 101 Series number 2nd part
103 102 Series number 4th part
104 103 Firmware version R
105 104 Malfunction & Service information R
106 105 Vmax [%] R/W
107 106 Absolute Vmax [l/s] LData R/W
108 107 HData

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

53
Energy Valve
Modbus Overview

Modbus Overview Continuation

Number Address Register R/W

109 108 Absolute Vmax [gpm] LData R/W
110 109 HData
111 110 Absolute Vnom [UnitSel] LData R
112 111 HData
113 112 Absolute Vnom [l/s] LData R
114 113 HData
115 114 Absolute Vnom [gpm] LData R
116 115 HData
117 116 Pmax [%] R/W
118 117 Absolute Pmax [kW] LData R/W
119 118 HData
120 119 Absolute Pmax [kBTU/h] LData R/W
121 120 HData
122 121 Absolute Pnom [UnitSel] LData R
123 122 HData
124 123 Absolute Pnom [kW] LData R
125 124 HData
126 125 Absolute Pnom [kBTU/h] LData R
127 126 HData
128 127 - R
129 128 - R

Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

130 129 - R
131 130 DeltaT Limitation [K] R/W
132 131 DeltaT Manager Status R
133 132 Setpoint DeltaT [K] R/W
134 133 Setpoint DeltaT [°F] R/W
135 134 Setpoint Flow at DeltaT [l/s] LData R/W
136 135 HData
137 136 Setpoint Flow at DeltaT [gpm] LData R/W
138 137 HData
139 138 - R
140 139 - R
141 140 Control Mode R/W
142 141 Unit Selection Flow R/W
143 142 Unit Selection Power R/W
144 143 Unit Selection Energy R/W
145 144 Setpoint Source R/W

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

54
 Energy Valve
Modbus Overview

Modbus Registers/Address

Modbus Object Register Register Description Values Default Capability Scale

Name Number Address
Setpoint [%] 1 0 Setpoint Relative in % The setpoint is 0…1000 0 Read/Write 0.01
related either to the position, the flow
(vMax) or the power (Pmax). See Con-
trol mode for more information.
Setpoint Source 145 144 The actuator has the possibility to be 0- Analog, 0 Read/Write
controlled from an analog input even 1-Bus
when integrated through BACnet. De-
pending on this setting the setppoint by
bus or analog will be followed. Analog:
Setpoint from analog signal 0…10V
on wire 3 Bus: Setpoint from BACnet,
register Number 1
Override 2 1 Override Control 1- Auto Auto Read/Write
2- Close
3- Open
4- V’ nom
5- V’ max
6- Motor Stop
7- P’nom
8- P’max
Relative 5 4 Relative Position in % 0…100 - Read Only 0.01
Position [%]
Absolute 6 5 Absolute Position in ° 0…90 - Read Only 0.01
Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

Position [°]
DeltaT_Mgr_ 132 131 Delta T Manager Status 0- Not Selected 0- Read Only
Status 1- Standby Not
Se-
2- Active lected
3- Scaling
Standby
4- Scaling Ac-
tive
Relative Flow 7 6 Relative Flow in % 0…100 0 Read Only 0.01
[%]
Absolute Flow 8/9 7/8 Absolute Flow Unit select related to unit 0…100,000 Read Only
[UnitSel] in Register 142
Absolute Flow 10/11 9/10 Absolute Flow in l/s 0…100,000 - Read Only 0.001
[l/s]
Absolute Flow 12/13 11/12 Absolute Flow in gpm 0…100,000 - Read Only 0.001
[gpm]
Setpoint 14/15 13/14 Setpoint Absolute Flow Unit select - Read Only 0.001
Absolute Flow related to unit in Register 142
[UnitSel]

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

55
Energy Valve
Modbus Overview

Modbus Object Register Register Description Values Default Capability Scale

Name Number Address
Set point 16 15 Setpoint Analog in Volt 0.000…10.00V - Read Only
Analog [V]
Temperature 1 17 16 Temperature 1 (remote) in °C -10…+120 - Read Only 0.01
[°C]
Temperature 1 18 17 Temperature 1 (remote) in °F 14…248 - Read Only 0.01
[°F]
Temperature 2 19 18 Temperature 2 (embedded) in °C -10…+120 - Read Only 0.01
[°C]
Temperature 2 20 19 Temperature 2 (embedded) in °F 14…248 - Read Only 0.01
[°F]
Delta 21 20 Delta Temperature in °C -500…+500 - Read Only 0.01
Temperature °C
Delta 22 21 Delta Temperature in °F -500…+500 - Read Only 0.01
Temperature °F
Glycol 23 22 Glycol Concentration in % 0…100 - Read Only 0.01
Concentration
[%]
Relative Power 24 23 Relative Power in % 0…100 - Read Only 0.01
[%]
Absolute Power 25/26 24/25 Absolute Power for Unit Selected in - Read Only 0.001
[UnitSel] Power Register 143
Absolute Power 27/28 26/27 Power in kW 0…2.147e+9 - Read Only 0.001
[kW]
Absolute Power 29/30 28/29 Power in kBTU/h 0…2.147e+9 - Read Only 0.001
[kBTU/h]

Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

Energy Cooling 31/32 30/31 Cooling Energy unit which is selected in - Read Only 1
[UnitSel] Register 144
Energy Cooling 33/34 32/33 Cooling Energy in kWh 0…2.147e+9 - Read Only 1
[kWh]
Energy Cooling 35/36 34/35 Cooling Energy in kBTU 0…2.147e+9 - Read Only 1
[kBTU]
Energy Heating 37/38 36/37 Heating Energy unit which is selected in 0…2.147e+9 - Read Only 1
[UnitSel] Register 144
Energy Heating 39/40 38/39 Heating Energy in kWh 0…2.147e+9 - Read Only 1
[kWh]
Energy Heating 41/42 40/41 Heating Energy in MJ 0…2.147e+9 - Read Only 1
[kBTU]
Vmax [%] 106 105 Maximum Flow Limit in % 0…100 100 Read/Write 0.01
Vmax [l/s] 107/108 106/107 Maximum Flow Limit in l/s 0…4000 - Read/Write 0.001
Vmax [gpm] 109/110 108/109 Maximum Flow Limit in gpm 0…1000 - Read/Write 0.001
Vnom [UnitSel] 111/112 110/111 Nominal volume which is selected in - - Read Only 0.001
Register 142
Vnom [l/s] 113/114 112/113 Nominal Volume in l/min 0…100,000 - Read Only 0.001
Vnom [gpm] 115/116 114/115 Nominal Volume in gpm 0…100,000 - Read Only 0.001

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

56
 Energy Valve
Modbus Overview

Modbus Object Register Register Description Values Default Capability Scale

Name Number Address
Pmax [%] 117 116 Maximum Power Limit in % 0…100 100 Read/Write 0.01
Pmax [kW] 118/119 117/118 Maximum Power Limit in kW 0…5000 - Read/Write 0.001
Pmax [kBTU/h] 120/121 119/120 Maximum Power Limit in kBTU/h 0…15,000 - Read/Write 0.1
Pnom [UnitSel] 122/123 121/122 Nominal Power Unit which is selected in - Read Only 0.001
Register 143
Pnom [kW] 124/125 123/124 Nominal Power in kW 0…2.147e+9 - Read Only 0.001
Pnom [kBTU/h] 126/127 125/126 Nominal Powerin kBTU/h 0…2.147e+9 - Read Only 0.001
ControlMode 141 140 The value defines the interpretation of 0- PosCtrl Flow- Read/Write 1
the setpoint 1- FlowCtrl Ctrl
2- PowerCtrl
DeltaT_ 131 130 Delta T Limitation 0- Disabled (off) Dis- Read/Write 1
Limitation 1- dT- Manager abled
2- dT Manager
Scaling
Set point DeltaT 133 132 Setpoint Delta T in K 0…+500 4 Read/Write 0.01
[K]
Set point DeltaT 134 133 Setpoint Delta T in °F 2…100 10 Read/Write 0.01
[°F]
Set point Flow_ 135/136 134/135 Setpoint Flow at Delta T in l/s (Flow 0…4000 0 Read/Write 0.001
DeltaT [l/s] saturation value)
Set point Flow_ 137/138 136/137 Setpoint Flow at Delta T in gpm (Flow 0…1000 0 Read/Write 0.001
DeltaT [gpm] saturation value)
Unit Select Flow 142 141 Selection of flow Unit Defines Registers 0- m3/s gpm Read/Write
8/9, 14/15, 111/112
Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

1- m3/h
2- l/s
3- l/min
4- l/h
5- gpm
Unit Select 143 142 Selection of Power unit defines unit 0- W kBTU/h Read/Write
Power Register No. 25/26, 122/123 1- kW
2- BTU/h
3- kBTU/h
4- Tons
Unirt Select 144 143 Selection of Energy unit defines unit 0- J kBTU Read/Write
Energy Register No. 31/32, 37/38 1- kWh
2- MWh
3- kBTU
4- tonh
5- MJ
6- GJ
ErrorState 105 104 Error State

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

57
Energy Valve
Terms and Conditions of Sale and Warranty

Terms and Conditions by the carrier’s agent and file with the carrier within 15 days after
receipt of product and notify Seller of the same. Seller is not
General liable for consequential damage to Client’s property or a third-
1.1. The following Terms and Conditions of Sale (“Terms”) apply party’s property resulting from the installation of damaged
to the sale of products described in this Product Guide Products.
(“Products”). As used herein, “Seller” or “Belimo” refers to
Belimo Aircontrols (USA) Inc. or Belimo Aircontrols (CAN) Inc., VI. Delivery
as applicable, and “Client” refers to the individual or business 6.1. Seller undertakes to make every attempt to adhere to its
entity that purchases the Products from Seller. These Terms stated delivery parameters and to make a timely delivery of the
shall apply unless the parties mutually agree to different terms Products but does not guarantee any delivery specifications.
and memorialize such agreement in writing signed by both Each contract entered into for the purchase of Products is not
Client and Seller. cancelable nor is Seller liable for any direct or indirect losses
that may arise, for any reason whatsoever, due to Seller’s failure
II. Price to meet any stated or assumed delivery schedules.
2.1. The Seller’s price for Products (the “Price”) is net, F.O.B.
Point of Origin, and is calculated in US currency for sales made VII. Return of Goods
by Belimo Aircontrols (USA), Inc. and calculated in Canadian 7.1. Products received by Client cannot be returned unless: (i)
currency for sales made by Belimo Aircontrols (CAN) Inc. Client alerts Seller that it intends to return such Products, (ii)
2.2. The Price, unless otherwise agreed upon, does not include Seller agrees to accept the return of such Products, (iii) Client
freight and packaging (wooden crates, pallets, etc), the costs of obtains a Return Material Authorization (“RMA”) number from
which will be charged to Client at cost for each shipment and Seller for the return of such Products, and (iv) Client follows all
shall be payable with payment of the Price. return instructions provided by the Seller. The RMA number
2.3. Orders for Products with a net value of less than US $300 must be clearly written on the outside of all packaging for any
(CAN $300) will be subject to a US $20 (CAN $20) handling fee returned Products. Only Products returned to the proper
(the “Handling Fee”). The Handling Fee will not be charged for location as instructed by Seller and identified with an RMA
orders of Products with a net value equal to or greater than number will be considered for credit.
US $300 (CAN $300) or for Products ordered through Seller’s 7.2. Only Products that are returned in original packaging may
eCommerce ordering system at: www.belimo.com. be accepted for return. All returned Products must be shipped
2.4. Seller reserves the right to make partial deliveries of orders to Seller at Client’s cost. Such returned Products must be
of Products, each of which deliveries may be invoiced received within 1 yr. from original sale date, in as-new condition,
separately by Seller. adequate for resale as new Products to qualify for credit. Client
2.5. The Price does not include charges for wiring diagrams, will be responsible for payment of a restocking charge for all
installation, and commissioning, which will be charged to Client returned Products in an amount no less than 20% of the invoice
separately and will be payable on demand. value of the Products (“Restocking Charges”). Product received
damaged or showing evidence of having been installed will be
III. Payment refused or assessed a higher restocking charge. Custom kits
3.1. Invoices are payable in US currency for sales made by designed to a Client’s unique specifications are not returnable.
Belimo Aircontrols (USA), Inc. and in Canadian currency for If Client requests product to be returned to them, the Client will
sales made by Belimo Aircontrols (CAN) Inc. and are due no be responsible for return shipping charges. See specific product

Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

later than 30 days from the date of invoice, without any literature for exclusions or exceptions.
deductions. 7.3. Returns that result from Seller errors will be credited in full
3.2. If Client fails to pay the entire invoice balance within 60 days and will not be subject to Restocking Charges.
from the date of the invoice, Client will be subject to an interest
charge of 2% per month (or the maximum rate permitted by law, VIII. Warranty
whichever is less) on the outstanding unpaid balance due to VIII.A 5-year Warranty
Seller. 8.1. Products that are listed in this Product Guide as carrying a
3.3. Clients who maintain outstanding balances for 45 days or 5-year warranty to a location in the United States or Canada
more after the date of invoice may be subject to restricted shall carry a 5-year warranty. The 5-year warranty is unconditional
shipments of Products or may be required to pay for all future for the first two years from the date of production of the
deliveries of Products on a cash-on-delivery basis. Products. After the first two years from the date of Sale, the
warranty shall be conditional and the warranty coverage shall
IV. Title and Risk not apply to damage to Products caused by ordinary wear and
4.1. Title to all Products shall remain with Seller and shall not tear, negligence or improper use by Client, or other causes
pass to Client until Seller has received full payment for the beyond the control of the Seller. Product specific terms of
Products. warranty with regard to warranty period or conditions of
warranty may apply to certain specified Products as stated in
V. Damage or Loss in Transit the documentation for those Products.
5.1. Seller assumes no liability for damage or loss of shipment
of Products, which risk shall at all times remain with the carrier. VIII.B 2-year Conditional warranty
All shipments must be unpacked and examined by Client 8.2. Products that are listed in this Product Guide as carrying a
immediately upon receipt. Any external evidence of loss or 2-year warranty to a location in the United States or Canada
damage must be noted on the freight bill accompanying the shall carry a 2-year warranty. The 2-year warranty is conditional
shipment of Products or carrier’s receipt and signed by the and the warranty coverage shall not apply to damage to
carrier’s agent at the time of delivery. Failure to do so will result Products caused by ordinary wear and tear, negligence or
in the carrier’s refusal to honor any claim relating to damage of improper use by Client, or other causes beyond the control of
Products. Client must also notify Seller of such damage by the Seller. Product specific terms of warranty with regard to
providing Seller with a copy of the freight bill or damage report warranty period or conditions of warranty may apply to certain
so that Seller can file a claim for loss or damage in transit with specified Products as stated in the documentation for those
the carrier. If the damage does not become apparent until the Products.
shipment is unpacked, Client must make a request for inspection

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

58
 Energy Valve
Terms and Conditions of Sale and Warranty

VIII.C General Warranty Terms IX. No Warranty for Non-HVAC Application

8.3. Seller’s warranty may be null and void in the event of any: 9.1. All Seller warranties shall extend only to HVAC use of the
(a) modification or unauthorized repairs of Products by Client, Products. If Products are used in non-HVAC applications (e.g.,
(b) unauthorized incorporation or integration of Products into or aircraft, industrial processes, etc.), Seller’s warranties shall not
with Client’s equipment, (c) use of Products in an unauthorized cover such Products. Client will be solely responsible for any
manner, or (d) damage to Products not caused by Seller. damage to or malfunction of Products or for any damage result-
8.4. Client must promptly notify Seller of Products’ alleged ing from such use of Products.
defect and provide Seller with other evidence and documenta-
tion reasonably requested by Seller. Before removing Products X. Liability Disclaimer
from service, Client should contact a Seller-authorized support 10.1. These Terms constitute the entire understanding and
technician by calling Belimo customer service. The contact agreement between Seller and Client regarding the warranties
information for Belimo customer service is listed on the back that cover Products and supersedes all previous understand-
page of Belimo’s Product Guide and Price List (“PGPL”) or may ings, agreements, communications and representations. Seller
be found at www.belimo.com. Belimo customer service will shall not be responsible for and Client does not have any right
work with field technicians to troubleshoot problems. Many to make any claim for damage that occurs to any property other
problems can be resolved over the phone. than Products. Seller shall in no way be responsible for any
8.5. If a problem cannot be resolved over the phone, an RMA costs incurred by Client in the determination of the causes of
number will be issued by Seller for return of the Products. Prior damage to any of Client’s property, for expert opinions, or for
to returning any Products under a warranty, Client must obtain any punitive or special, incidental or consequential damages of
an RMA number from Seller, along with shipping instructions for any kind whatsoever. Seller’s warranty is extended to the Client
the return. The RMA number must be clearly written on the only and is non-transferrable.
outside of the box containing the returned Products. Only
Products returned to the proper location and identified with an 10.2. Seller shall not be liable for any damage resulting from or
RMA number will be accepted by the Seller. contributed by Client or third parties acting within the scope of
8.6. All returned Products should be packaged appropriately to responsibility of Client or such third party when:
prevent further damage. Seller reserves the right to refuse any 1. Products are used for non-HVAC applications, such as in
returned material if improperly packaged or labeled (without an aircrafts, industrial processes, etc.;
RMA number). Products returned without proper RMA docu- 2. Client uses the Products without complying with applicable
mentation will void Seller’s warranty. law or institutional regulations or Belimo data and installation
8.7. Products found to be defective for which a warranty is sheets or Client uses the Products without following good
applicable will either be replaced or repaired at the Seller’s dis- industry practice;
cretion. Seller is not responsible for charges that Client may 3. Products are used by personnel who have not received
incur as a result of the removal or replacement of Products. suitable instruction; or
8.8. Repaired or replacement Products are shipped from Seller 4. Products are modified or repaired without the written
via ground shipment. Other shipping methods are available at approval of Seller.
the sole expense of the Client. When requested to do so, Client shall immediately release Seller
8.9. Repaired, replaced or exchanged Products will carry a war- in full from any possible third party claims resulting in connec-
ranty for a period of time equal to the greater of: (i) the remain- tion with the circumstances listed above. This also applies to
der of the original 5-year warranty or 2-year warranty that was claims in connection with product liability.
applicable to the repaired, replaced or exchanged Products, or 10.3. If Client becomes aware that any third party has made or
Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

(ii) six months, effective from the date the repaired, exchanged appears likely to make any claim regarding Products (including,
or replaced Products are shipped by Seller (the “Replacement without limitation, regarding Product defects or rights infringed
Warranty Period”). by Products), then Client shall immediately inform Seller and
8.10. Advanced replacement Products for Products covered afford to Seller all assistance that Seller may require to enforce
under warranty may be obtained from Seller after the Belimo its rights and defend such claim.
customer service troubleshooting process has been completed.
For industrial products (such as butterfly valves), a purchase XI. Proper Law and Jurisdiction
order is required. The purchase order will be credited upon the 11.1. All sales of Products under these Terms and the warran-
receipt and verification by Seller of the returned defective ties described herein shall be governed by the laws of the State
Products. For non-industrial products, an invoice will be issued of Connecticut, and the parties agree to submit to the exclusive
and shall be due and payable if the returned Products are not jurisdiction of the Federal and state courts located in the State
received by Seller within 60 days from the date that the replace- of Connecticut with respect to any dispute arising from the sub-
ment Products are shipped. Additional charges may apply if the ject matter hereof. The parties hereby waive all rights to a jury
nature of the problem has been misrepresented by Client. trial in connection with any claims relating to the subject matter
8.11. Both the conditional and unconditional warranties cover hereof.
the Products only, and do NOT cover labor associated with the
troubleshooting, removal or replacement of such Products.
8.12. New Products ordered in an attempt to circumvent the
warranty process may NOT be reimbursed if, upon receipt of
returned Products, it is determined that the defect in the
returned Products is actually field related, or the Products have
been returned for cosmetic reasons only.
8.13. Advanced replacement Products for butterfly valve actua-
tors may not be new, but have been verified by the Seller for
electrical and mechanical operation. Such Products carry the
full warranty for the entire Replacement Warranty Period.

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

59
Energy Valve
Glossary of Terms

∆T dT Manager Scaling
Measured differential temperature between water supply and return. An option in the Delta T Manager logic that produces a variably scaled
dT setpoint.
Analog
A linear signal from one device to another. It used to move or read delta T (∆T)
values. It is used by a controller to modulate an actuator. Typical The difference in the supply and return temperatures of a coil.
analog signal range is 2-10 VDC, 0-10 VDC, or 4-20 mA.
dT setpoint
BACnet The set point used by the Delta T Manager logic. When used with dT
A standard world-wide communication protocol that is used in building Manager it is a fixed setting. When used with dT Manager Scaling it
automation. BACnet uses two common communication mechanisms, becomes a calculated variable over a scaled range.
BACnet IP which communicates over Ethernet networks. BACnet MS/
TP communicates over 2 or 3-wire RS485 networks. Flow Saturation Limit Value / Flow Saturation
A setting used with dT Manager Scaling to reset the Delta T Limiting
BMS (Building Management System) Value and create a variable, dT setpoint.
A computer-based control system installed in buildings to control and
monitor the building’s mechanical and electrical equipment. Ghost Energy
Leaky control valves can create ghost heating and cooling demand
CCV (Characterized Control Valve) and excess ventilation, which comes with a need to dehumidify or
A Belimo patented ball valve with characterizing disc that provides preheat. Also, there is ghost pumping for the additional chilled water
equal percentage flow characteristic with high rangeability, zero and heating water flows along with ghost heating and cooling. A 1%
leakage, and high close-off. leakage creates a 5 to 10% loss of energy.

DDC (Direct Digital Control) MP-Bus (MP)

A controller with software to operate control valves, dampers and A Belimo communication protocol. The ZTH US tool uses this protocol
other devices. to view and change actuator settings.

Delta T Limit Value P’max

A setting used by the Delta T Manager to limit coil overflow. The maximum thermal power setting.

Delta T Manager P’nom

A patented flow limiting logic applied to the Energy Valve Control The maximum thermal power of the heat exchanger.
Modes.
V’max
dT Manager The maximum valve flow setting.
An option in the Delta T Manager logic that produces a fixed dT

Tech.Doc - 01/18 - Subject to change. © Belimo Aircontrols (USA), Inc.

setpoint. V’nom
The maximum valve flow.

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

60
www.EnergyValve.com

Belimo Americas
USA, Latin America, and the Caribbean: www.belimo.us
Canada: www.belimo.ca
Brazil: www.belimo.br

Belimo Worldwide: www.belimo.com