DX-905

Clean fluids work better and last longer

DESIGN AND
OPERATING FEATURES

Manual-cleaning
Excellent media-free filtration
Wear protection liner and inserts
Product feed pump and pre-filter,
designed to be fed from headers pressure
or its own pump
Light and heavy phase centripetal pumps
Back pressure valve on heavy phase and
light phase discharge pipe for fine tuning
of separation
NEMA 12-control panel w/Allen
Bradley PLC and Touchscreen
Integral sludge/tramp oil tank with waste
pump
Set of regulating rings
Mounting isolators
Set of tools

Get Results With Your Select the Program That is

Industrial Fluids Right for You
The DX-905 is designed to efficiently remove High-speed centrifugation is available for
solids, insoluble contaminants, and tramp oil purchase, or rental with the Purification
from water-based fluids, as well as water Service agreement. With the nation’s largest
and solids from straight oils. The unit privately-owned fleet of purification
produces a very high peripheral centrifugal modules, a large service staff and hundreds
force for the removal of fine particles (0.1 to of years of combined experience in
50 microns) and the efficient separation of separation technologies, Trucent has
two immiscible liquids (e.g. tramp oil from unparalleled capabilities and response time.
water-based metalworking fluids). Modules And, with the Purification Service, you will
are custom designed for your particular fluid experience all the benefits of clean industrial
issues. The removal of contaminants greatly fluids without capital expenditure, without
BEFORE AFTER
improves fluid performance and longevity. long-term commitments and without any
For straight oils, this means removal of solids service obligations. Trucent takes care of the
and free water. For coolants, efficient machine for you, including all parts and all
Note the difference in both
removal of fines, tramp oil, and bacteria has labor and with our rapid response promise,
a tremendous positive impact, such as free upgrades and even machine
color of product and removal of
longer life, reduced chemical purchases and replacement if necessary. You reap the oil layer
disposal costs, reduced biocide usage, better benefits, we’ll take care of the rest.
finish and size control, and better tool life. It
is all available without capital investment or
long-term commitment.

CLEAN FLUIDS WORK BETTER

trucent.com 877.280.7212 7400 Newman Blvd, Dexter, MI 48130
AND LAST LONGER.
 DX-905
Dimensions and Specifications

Working This DX-905 permits the separation between

solids/tramp oil and industrial or in-process
DIMENSIONS AND WEIGHTS
Length 52 in
Principle fluids. The separation takes place in the bowl of
the separator, rotating at a speed of 10,200
rpm. The product flows (fig 3.1) into the bowl
Width 32 in

through a feed pipe (1) and into the distributor Height 75 in

(2) undergoing acceleration until it reaches the Gross Weight 2,000 lbs
CENTRASEP DX-905 bowl rotating speed. The distributor (2)
PURIFICATION MODULE conveys the product to the disk stack (3) where TECHNICAL DATA
the separation between solids/tramp oil and in-
process fluid takes place. Disks divide the Hydraulic Capacity 396 gph
internal space of the bowl into many thin Solids Chamber .14 gal
layers. A greater number of disks, along with Capacity
other factors, increase separation efficiency. Bowl Speed 10,200 rpm
The tramp oil, or light phase, flows toward the
Motor 2 hp
center of the bowl and leaves the disk
assembly via its inner edge. The in-process Centrifugal Force 14,200 g-forces
fluid, or heavy phase, flows toward the bowl 440 volts
periphery. Both phases rise in the disk stack to
3 phase
reach the two upper chambers of the bowl.
Here two fixed centripetal pumps (4-5) convey Utility Requirements 60 hertz
them separately under pressure to their
30 amps
respective outlets (6-7). Simultaneously, the
psi
solid impurities (9) collect on the interior of the 29
waterline
disks. T h e y a r e continually forced to the
periphery of the bowl body (8) where they *Actual capacity contingent on the characteristics of the product
must be removed manually. Valves and to be treated (solids, density, etc.) and on the required degree of
purity of clarified phases
instrumentation needed to control and
regulate the separator are located on inlet and
outlet pipelines.

CLEAN FLUIDS WORK BETTER

trucent.com 877.280.7212 7400 Newman Blvd, Dexter, MI 48130
AND LAST LONGER.