Scribd
Upload
170 views2 pages

NCT-196 Setup

Uploaded by

Michael Karantzias
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
170 views2 pages

NCT-196 Setup

Uploaded by

Michael Karantzias
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

4.

5 NCT-196N DSC/NBDP Modem


4.5.1 Self ID, Navigation and Radiotelephone Setting
The settings described in this section have been made prior to shipment from the factory.

ATTENTION
To enable setting adjustment, remove the cover of the NCT-196N DSC/NBDP MODEM
and insert the switch(S1)-No.3 into the OFF. When adjustment is complete, re-insert
the switch(S1)-No.3 into the ON and replace the cover.

S1 S1

8
7

7
6

6
5

5
4

4
3

3
2

2
OFF

OFF
1

1
Insert the S1-3 to Re-insert the
OFF at the time of S1-3 to ON after
Self-ID setting. Self-ID setting.

Note Dip switch setting

Switch No. Function Default setting


S1-1 Modem function ON: DSC only, OFF: DSC and NBDP OFF
S1-2 EEPROM initialize ON: Disenable, OFF: Enable (expect ID) ON
S1-3 EEPROM writing ON: Disenable, OFF: Enable ON
S1-4 TEST signal sending ON: Disenable, OFF: Enable OFF
S1-5 AF signal wait ON: Normal, OFF: Factory setting ON
S1-6 HT signal using ON: Not use, OFF: Use ON
S1-7 - ON
S1-8 - ON

Procedure
(a) Both press MENU and “POWER SWITCH” to access the following the “INSTALLATIONSETUP”
menu.

INSTALLATION SETUP
Self-ID : 111111111
Group-ID : 022222222
Navigation : NMEA0183

Serial cont: ON
Data clear : OFF
SPACE signal send
MARK signal send
DOT signal send
70-TIME MESSAGE send
WKR frequency : 2,187.5
WKR step test
History

54
(b) Select “Self-ID” using ▼ / ▲ , input the Self-ID (9-digit) using the number keys and
press ENT .

(c) If a Group-ID is assigned, select “Group-ID” using ▼ / ▲ , input the Group-ID (8-digit) and
press ENT .

(d) Select “Navigation” using ▼ / ▲ , specify the navigation data format using / and
press ENT .

ATTENTION
There are two types of navigation data formats, NMEA 0183 and JRC format. For
normal operation, specify NMEA 0183.

NMEA0183 format
(A) Transmission format
Transmission method: Asynchronous
baud rate : 4800bps
Start bit : 1bit
Data bit : 8bit
Stop bit : 1bit
Parity : None
(B) Data format
GLL : Position data ( Lat / Lon ) and UTC time data (IEC61162-1)
Position data ( Lat / Lon ) (NMEA Version 1.5)
ZDA : UTC time data and date ( year, month, day ) data (IEC61162-1)
ZLZ : UTC time data (NMEA Version 1.5)
ZZU : UTC time data (NMEA Version 1.5)
VHW : Water speed and heading data (IEC61162-1)
VTG : Course over ground and ground speed (IEC61162-1)
RMC : Position data ( Lat / Lon ), UTC time data,
and ( year, month, day ) data (IEC61162-1)

JRC format
(A) Transmission format
Transmission method: Asynchronous
baud rate : 1200bps
Start bit : 1bit
Data bit : 8bit
Stop bit : 2bit
Parity : None

(B) Data format


“F” or “D” +80H : Position ( Lat / Lon ), date ( year, month, day ) data and time data, “@”
+80H.
Note If a time difference is set on JRC format navigation equipment, local time, not UTC
time, is output. Set the time difference to zero or use the NMEA0183 format.

(e) Select “Serial cont” using ▼ / ▲ , specify “ON” using / and press ENT .

(f) Press FUNC and then 9 (SAVE). The contents of the settings are written to memory
(saved) and the “DSC watching” display returns. This completes the operation setting.

Note Press FUNC and then 4 (QUIT) to cancel the set contents and end the setting operation.

55

You might also like