SERVICE BULLETIN

REVISION TRANSMITTAL SHEET

AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX FRANCE
Tel : (33) 5 61 93 33 33
Telex : AIRBU 530526F
Fax : (33) 5 61 93 42 51

ATA SYSTEM : 00

TITLE : GENERAL - DESIGN WEIGHTS - INCREASE MTOW TO 77 TONS

MODIFICATION No. : 23264K3065, 23932K3484, 26059K4841

This page transmits Revision No. 63 of Service Bulletin No. A320-00-1013

ADDITIONAL WORK

No additional work is required by this revision for aircraft modified by any previous issue.

REASON

Revision No. 63 issued to add aircraft MSN 1697 and 1732 for operator BMA.

CHANGES

SUMMARY :

- EFFECTIVITY

. Operators updated.

- CONCURRENT REQUIREMENTS

. Effectivity updated.

PLANNING INFORMATION :

- EFFECTIVITY

. 1.A. Effectivity updated.

- CONCURRENT REQUIREMENTS

. 1.B. Effectivity updated.

FILING INSTRUCTIONS

This Service Bulletin has been generated electronically and is reissued as a complete document.
Replace the complete document.

Put this Revision Transmittal Sheet in front of the Service Bulletin.

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 1 of 5

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN
REVISION TRANSMITTAL SHEET

HISTORY OF PREVIOUS REVISIONS

This is only applicable for Revision No. 25 and subsequent. If information is required for Revisions
issued previous to this, please check your copies of Revision Transmittal Sheets or contact AIRBUS.

Revision No. 25 issued to inform DA of the addition of aircraft MSN 1156 and 1235 for operator JEU.

Revision No. 26 issued to inform DA of the addition of aircraft MSN 0235 for operator VLE and aircraft
MSN 0243, 0249, 0250, 0251, 0334, 0335 and 0440 for operator SAA.

Revision No. 27 issued to inform DA of the addition of aircraft MSN 0414 and 0430 for operator I2L.

Revision No. 28 issued to add aircraft MSN 0951, 0999, 1138, 1168, 1217, 1226, 1473 and 1480 for
operator AZA, and aircraft MSN 1489 for operator EEZ.

Revision No. 29 issued to add aircraft MSN 0407 for operator RJA.

Revision No. 30 issued to add aircraft MSN 1411 for operator SSV.

Revision No. 31 issued to add aircraft MSN 0288 and 0331 for operator AAA, aircraft MSN 1413, 1439
and 1450 for operator S2A and aircraft MSN 0087, 0088 and 0569 for operator RJA.

Revision No. 32 NOT EXISTING

Revision No. 33 issued to add aircraft MSN 0234 for operator TAP.

Revision No. 34 issued to add aircraft for operator ACA.

Revision No. 35 issued to add aircraft MSN 0870 for operator F2I, aircraft MSN 0640 for operator
I2L and aircraft MSN 0676 for operator MEA.

Revision No. 36 issued to add aircraft MSN 0142 for operator P2C.

Second presentation issued to add kit A08R00 for aircraft MSN 0142.

Revision No. 37 issued to add aircraft MSN 0565 and 0661 for operator AWE.

Revision No. 38 issued to add aircraft MSN 0112, 2158 and 2166 for operator ABY.

Revision No. 39 issued to add aircraft MSN 0204 for operator JET.

Revision No. 40 issued to add aircraft MSN 2278, 2349 for operator ABY and aircraft MSN 0293 for
operator AMC.

Revision No. 41 issued to add aircraft MSN 0030 for operator EGN.

Revision No. 42 issued to add aircraft MSN 0420 and 0436 for operator G2X.

Revision No. 43 issued to add aircraft MSN 0024 for operator LAO and aircraft MSN 0026 for operator
MHS.

Revision No. 44 issued to add aircraft MSN 0244 for operator AFR and aircraft MSN 0726 for operator
RNV.
DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 2

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN
REVISION TRANSMITTAL SHEET

Revision No. 45 issued to add aircraft MSN 0215 for operator AFR.

Revision No. 46 issued to add aircraft MSN 1924 and 1949 for operator AFR.

Revision No. 47 issued to add aircraft MSN 1992 and 2016 for operator HEJ.

Revision No. 48 issued to add aircraft MSN 0667 for operator NLY.

Revision No. 49 issued to add aircraft MSN 2390 and 2425 for operator RZO.

Revision No. 50 issued to add aircraft MSN 0140 and 0157 for operator LBT.

Revision No. 51 issued to add aircraft MSN 0441 for operator TNA and delete aircraft MSN 0024, 0026
and 0030 from the effectivity.

Revision No. 52 issued to add aircraft MSN 1054 for operator THY.

Revision No. 53 issued to add aircraft MSN 0768, 0776, 1137 and 1150 for operator AUA.

Revision No. 54 issued to add aircraft MSN 0138 and 0148 for operator ANA.

Revision No. 55 issued to add aircraft MSN 2540, 2596 and 2623 for operator VLG and MSN 1063
for operator CLI.

Revision No. 56 issued to add aircraft MSN 1189 and 1478 for operator AUA and aircraft MSN 3040
for operator VLG.

Revision No. 57 issued to add aircraft MSN 1484 for operator IBE.

Revision No. 58 issued to add aircraft MSN 0580 for operator 86Z.

Revision No. 59 issued to add aircraft MSN 0934 for operator D2F and aircraft MSN 1200 for operator
VLK.

Revision No. 60 issued to add aircraft MSN 1379 for operator IBE.

Revision No. 61 issued to add aircraft MSN 3769 and 3883 for operator TAP.

Revision No. 62 issued to add MSN 1454 for operator IBE and remove MSN 0313, 0363 and 0445
for operator 31V.

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 3

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN
REVISION TRANSMITTAL SHEET

REVISION SEQUENCE

ORIGINAL : Mar 10/93

REVISION No. : 01 - Jan 18/95
REVISION No. : 02 - May 18/95
REVISION No. : 03 - Jun 14/95
REVISION No. : 04 - Jul 10/95
REVISION No. : 05 - Aug 08/95
REVISION No. : 06 - Sep 19/95
REVISION No. : 07 - Oct 16/95
REVISION No. : 08 - Nov 11/95
REVISION No. : 09 - Jun 06/96
REVISION No. : 10 - Sep 30/96
REVISION No. : 11 - Oct 15/96
REVISION No. : 12 - Apr 18/97
REVISION No. : 13 - Sep 12/97
REVISION No. : 14 - Dec 12/97
REVISION No. : 15 - Apr 07/98
REVISION No. : 16 - Jun 03/98
REVISION No. : 17 - Jul 24/98
REVISION No. : 18 - Aug 31/98
REVISION No. : 19 - Dec 16/98
REVISION No. : 20 - Feb 26/99
REVISION No. : 21 - Sep 24/99
REVISION No. : 22 - Dec 13/99
REVISION No. : 23 - Mar 28/00
REVISION No. : 24 - May 31/00
REVISION No. : 25 - Jul 11/00
REVISION No. : 26 - Nov 30/00
REVISION No. : 27 - Feb 14/01
REVISION No. : 28 - Sep 17/01
REVISION No. : 29 - Dec 21/01
REVISION No. : 30 - Feb 25/02
REVISION No. : 31 - Apr 26/02
REVISION No. : 32 - Aug 22/02
REVISION No. : 33 - Oct 25/02
REVISION No. : 34 - Feb 10/03
REVISION No. : 35 - Sep 25/03
REVISION No. : 36 - Mar 02/04
REVISION No. : 37 - Mar 18/04
REVISION No. : 38 - Jun 07/04
REVISION No. : 39 - Jul 29/04
REVISION No. : 40 - Sep 06/04
REVISION No. : 41 - Dec 17/04
REVISION No. : 42 - Mar 02/05
REVISION No. : 43 - Apr 28/05
REVISION No. : 44 - Dec 07/05
REVISION No. : 45 - Jan 26/06
REVISION No. : 46 - Apr 05/06
REVISION No. : 47 - May 05/06
REVISION No. : 48 - Jul 26/06
REVISION No. : 49 - Aug 22/06

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 4

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN
REVISION TRANSMITTAL SHEET

REVISION No. : 50 - Oct 18/06

REVISION No. : 51 - Apr 05/07
REVISION No. : 52 - Sep 18/07
REVISION No. : 53 - May 28/08
REVISION No. : 54 - Jun 26/08
REVISION No. : 55 - Sep 04/08
REVISION No. : 56 - Oct 10/08
REVISION No. : 57 - Dec 19/08
REVISION No. : 58 - Apr 30/09
REVISION No. : 59 - Jun 26/09
REVISION No. : 60 - Sep 21/09
REVISION No. : 61 - Oct 27/09
REVISION No. : 62 - Feb 24/10
REVISION No. : 63 - Apr 01/10

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 5

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

This Page Intentionally Left Blank

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 6

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN
SUMMARY

AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX FRANCE
Tel : (33) 5 61 93 33 33
Telex : AIRBU 530526F
Fax : (33) 5 61 93 42 51

This summary is for information only and is

not approved for modification of the aircraft

ATA SYSTEM : 00

TITLE : GENERAL - DESIGN WEIGHTS - INCREASE MTOW TO 77 TONS

MODIFICATION No. : 23264K3065, 23932K3484, 26059K4841

REASON/DESCRIPTION/OPERATIONAL CONSEQUENCES

This Service Bulletin is issued further to an operator’s request.

This Service Bulletin certifies A320-200 aircraft at the following weights :

- Maximum Take Off Weight (MTOW) is increased from 73.5 T or 75.5 T to 77.0 T

- Maximum Landing Weight (MLW) remains unchanged at 64.5 T

- Maximum Zero Fuel Weight (MZFW) remains unchanged at :

. 60.5 T for aircraft on which Mod. No. 23900K3471 (INCREASE DESIGN WEIGHT TO 61 T MZFW)
is not embodied

. 61.0 T for aircraft on which Mod. No. 23900K3471 (INCREASE DESIGN WEIGHT TO 61 T MZFW) or
Service Bulletin No. A320-00-1030 is embodied.

This Service Bulletin also replaces the tyre pressure placards on the Main Landing Gear (MLG) and on the
Nose Landing Gear (NLG) to show the new MTOW and the related tyre pressure.

Accomplishment of this Service Bulletin will satisfy the operator’s request.

EVALUATION TABLE

COMPLIANCE Optional CANCELS INSPECTION SB No

POTENTIAL AD No A/C OPERATION AFFECTED Yes

RELIABILITY AFFECTED No PAX COMFORT AFFECTED No

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 1 of 6

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN
SUMMARY

EVALUATION TABLE

COST SAVING No ETOPS AFFECTED No

STRUCTURAL LIFE EXTN No VENDOR SB INVOLVED No

KIT PRICE (USD) See SB

MODIFICATION CLASSIFICATION

MAJOR 23264K3065 23932K3484

MINOR 26059K4841

As per EASA IR 21, a minor change is one that has no appreciable effect on the mass, balance, structural
strength, reliability, operational characteristics affecting the airworthiness of the product. All other changes
are major changes.

EFFECTIVITY

This Service Bulletin is applicable to this (these) operator(s) :

47Y 50X 51X 66X 69X 76U 82U 86Z 98X AAF AAN ABQ ABY ACA AFR AHY ALK ART AUA AWW AZA
BGH BIE BMA BTV C9G CSA CYP D2F ETD F2I FHY G2X GFA HEJ I2L IAC IBE IRA ISR JBU JET KKK
KZR LBT LZB MDL MLD MON MXA OHY RYW RZO SBI SDM SHY SSV STZ SUD SVR TAE TAM TAP TAS
TCW TCX UDC USA VLG VLK XLF

NOTE : This Service Bulletin is written for the operators listed above. The modification in this Service
Bulletin can be done by other operators.
If other operators want to do this modification, use the RFC/RMO procedure and write to :

AIRBUS
CUSTOMER SERVICES DIRECTORATE
SC Department
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX
FRANCE

CONCURRENT REQUIREMENTS

For MSN 0204 0215 0244 0525

Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment of the following
Service Bulletin(s) :

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 2

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN
SUMMARY

Service Bulletin No. A320-00-1019

For MSN 2540 2596 2623 3040

Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment of the following
Service Bulletin(s) :

Service Bulletin No. A320-00-1203

For MSN 0138 0148

Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment of the following
Service Bulletin(s) :

Service Bulletin No. A320-00-1206

For MSN 0087 0088 0112 0132 0140 0142 0157 0163 0164 0168 0169 0174 0175 0179 0183 0186 0187
0189 0190 0193 0203 0210 0220-0222 0228 0230-0235 0242 0243 0248-0251 0253-0256 0265 0277 0279
0283 0284 0288-0290 0293-0295 0299 0301 0302 0305 0309-0311 0316 0324 0325 0330 0331 0333-0335
0341-0343 0345 0348-0350 0354 0357 0359 0362 0375 0378 0384 0391-0395 0403 0404 0407 0411 0414
0415 0419 0420 0421 0424-0426 0428-0430 0436 0437-0438 0440 0441 0443 0444 0447-0449 0453 0455
0459-0461 0466 0471 0476 0478 0496 0497 0527 0537 0543 0565 0569 0580 0640 0661 0667 0676 0726
0768 0776 0795 0870 0934 0951 0999 1054 1063 1137 1138 1150 1156 1168 1189 1200 1217 1226 1235
1379 1411 1413 1439 1450 1454 1473 1478 1480 1484 1489 1697 1719 1732 1864 1874 1924 1949
2016 2158 2166 2278 2349 2390 2425 3769 3883

Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment of the following
Service Bulletin(s) :

Service Bulletin No. None

REFERENCES/REPERCUSSIONS

TFU : None

OEB : None

AOT : None

SIL : None

LIFE LIMIT : None

LINE MAINTENANCE AFFECTED : No

OTHERS : None

NATURE OF THE WORK

AIRCRAFT : YES

EQUIPMENT : NO

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 3

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN
SUMMARY

HARD : NO

SOFT : NO

OBRM : NO

MANPOWER

Config. 01, Config. 06, Config. 09

TOTAL MANHOURS 3.0

ELAPSED TIME (HOURS) 3.0

Config. 02 thru Config. 05, Config. 07, Config. 10 thru Config. 11

TOTAL MANHOURS 1.0

ELAPSED TIME (HOURS) 1.0

Config. 08

TOTAL MANHOURS 0.5

ELAPSED TIME (HOURS) 0.5

MATERIAL INFORMATION

AIRCRAFT DATA

Config. 01 and Config. 02

Kit 001013A01R21

Placards

Config. 03

Kit 001013A02R06

Placards

Config. 04

Kit 001013A03R05

Placards

Config. 05

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 4

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN
SUMMARY

Kit 001013A04R08

Placards

Config. 06 and Config. 07

Kit 001013A05R05

Placards

Config. 08

Kit 001013A06R00

Placards

Config. 09 and Config. 11

Kit 001013A07R00

Placards

Config. 10

Kit 001013A08R00

Placards

APPENDICES

None

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 5

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN
SUMMARY

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 6

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX FRANCE
Tel : (33) 5 61 93 33 33
Telex : AIRBU 530526F
Fax : (33) 5 61 93 42 51

ATA SYSTEM : 00

TITLE : GENERAL - DESIGN WEIGHTS - INCREASE MTOW TO 77 TONS

MODIFICATION No. : 23264K3065, 23932K3484, 26059K4841

This document contains AIRBUS PROPRIETARY INFORMATION and shall at all times remain the property
of AIRBUS; no intellectual property right or licence is granted by AIRBUS in connection with any information
contained in it. It is delivered on the express condition that said document and the information contained in
it shall be treated as confidential, shall not be used for any purpose other than that for which it is hereby
delivered. It shall not be disclosed in whole or in part to third parties and shall not be duplicated in any
manner (except for the purposes of performing the tasks described hereunder and provided that any recipient
of such document shall comply with the conditions herein), without AIRBUS’ prior written consent.

1. PLANNING INFORMATION

A. EFFECTIVITY

(1) Models

320-211 320-212 320-214 320-231 320-232 320-233

(2) Aircraft

(a) Effectivity by MSN

This Service Bulletin is applicable to aircraft MSN :

0087 0088 0112 0132 0138 0140 0142 0148 0157 0163 0164 0168 0169 0174
0175 0179 0183 0186 0187 0189 0190 0193 0203 0204 0210 0215 0220-0222
0228 0230-0235 0242-0244 0248-0251 0253-0256 0265 0277 0279 0283 0284
0288-0290 0293-0295 0299 0301 0302 0305 0309-0311 0316 0324 0325 0330 0331
0333-0335 0341-0343 0345 0348-0350 0354 0357 0359 0362 0375 0378 0384
0391-0395 0403 0404 0407 0411 0414 0415 0419-0421 0424-0426 0428-0430
0436-0438 0440 0441 0443 0444 0447-0449 0453 0455 0459-0461 0466 0471 0476
0478 0496 0497 0525 0527 0537 0543 0565 0569 0580 0640 0661 0667 0676 0726
0768 0776 0795 0870 0934 0951 0999 1054 1063 1137 1138 1150 1156 1168 1189
1200 1217 1226 1235 1379 1411 1413 1439 1450 1454 1473 1478 1480 1484 1489
1697 1719 1732 1864 1874 1924 1949 2016 2158 2166 2278 2349 2390 2425 2540
2596 2623 3040 3769 3883

NOTE : Mod. No. 23932K3484 is only applicable to aircraft models 320-232/233.

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 1 of 55

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

NOTE : Mod. No. 23264K3065 is applicable to all aircraft listed above except
aircraft MSN 0455 and 0471.

NOTE : Mod. No. 26059K4841 is only applicable to aircraft on which Mod. No.
22269K2319 (INCREASE DESIGN WEIGHT TO 75.5 T) is embodied.

(b) Effectivity by Operator

The Operator/MSN relationship is provided for information only and is correct at the
time of issue in accordance with the information available to AIRBUS. Any future
changes resulting from transfer of an aircraft from one operator to another will not be
reflected in this list unless the Service Bulletin is revised for another reason.

OPERATOR MSN

47Y 0394

50X 0543 0661

51X 0375

66X 0426

69X 0444

76U 0302

82U 0438

86Z 0466

98X 0342

AAF 0244

AAN 0430 0527

ABQ 0443

ABY 2158 2166 2278 2349

ACA 0174 0175 0183 0210 0231 0232 0233 0242 0248 0253 0254
0255 0265 0277 0284 0290 0309 0324 0330 0341 0378 0403
0404 1719 1864 1874

AFR 0186 0187 0228 0235 1924 1949

AHY 0331

ALK 0169

ART 0142 0310 0311 0359 0726

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 2

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

OPERATOR MSN

AUA 0768 0776 1137 1150 1189 1478

AWW 0393 0414

AZA 0951 0999 1138 1168 1217 1226 1473 1480 1489

BGH 0221 0294 0305 0349

BIE 0293

BMA 1697 1732

BTV 0168 0441 0449 0460 0461

C9G 0453

CSA 1439 1450

CYP 0256 0295 0316

D2F 0299 0407

ETD 0350

F2I 0193 0283

FHY 0132 0288 0580

G2X 0234 0289

GFA 0325 0419 0459 0497 0537

HEJ 0087 0088

I2L 0496

IAC 0354 0362 0411 0478

IBE 1454

IRA 0345

ISR 0333 0384

JBU 1156 1235

JET 0163 0204 0215 0421

KKK 0640 0676

KZR 2016
DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 3

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

OPERATOR MSN

LBT 0112 0222 0301 0348

LZB 2540 2596

MDL 0279 0391

MLD 0249

MON 0392

MXA 0164 0179 0357 0415 0428 0447

OHY 0455 0471

RYW 0569

RZO 0795 2390 2425

SBI 2623

SDM 0525

SHY 0138 0148

SSV 1411

STZ 0190 0420 0436

SUD 3040

SVR 0140 0157 0203 0220 1063 1484

TAE 0934

TAM 0243 0250 0251 0334 0335 0440

TAP 0395 0870 3769 3883

TAS 0667 1054

TCW 0425

TCX 0424 0429 0437 0476

UDC 0230

USA 0448 0565

VLG 1413

VLK 1200 1379

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 4

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

OPERATOR MSN

XLF 0189 0343

(c) Effectivity by MSN and Kit/Configuration

The Kits and configurations applicable to these MSNs are given at the end of this list

0132 0186-0187 0204 0215 0228 0234 0244 0256 0295 0316 0395 0420 0436 0440
1063 1200 1379 1454 1473 1480 1484 1489 1924 1949 2016

KIT No. QTY PER A/C CONFIGURATION

001013A01R21 1 01

The Kits and configurations applicable to these MSNs are given at the end of this list

0087-0088 0112 0140 0157 0163-0164 0168-0169 0174-0175 0179 0183 0193 0203
0210 0220-0222 0230-0233 0242-0243 0248-0251 0253-0255 0265 0277 0279
0283-0284 0288-0290 0293-0294 0299 0301-0302 0305 0309-0311 0324-0325
0330-0331 0333-0335 0341-0343 0345 0348-0350 0359 0362 0375 0378 0384
0391-0392 0403-0404 0414 0419 0421 0424 0426 0428-0430 0437-0438 0459 0466
0497 0537 0569 0580 0640 0676 0768 0776 0795 0870 0934 1054 1137 1150 1189
1411 1413 1439 1450 1478 1697 1719 1732 1864 1874 2158 2166 2278 2349 2390
2425 2540 2596 2623 3040 3769 3883

KIT No. QTY PER A/C CONFIGURATION

001013A01R21 1 02

The Kits and configurations applicable to these MSNs are given at the end of this list

0425 0441 0448 0453 0460-0461

KIT No. QTY PER A/C CONFIGURATION

001013A02R06 1 03

The Kits and configurations applicable to these MSNs are given at the end of this list

0189-0190 0235 0407 0449

KIT No. QTY PER A/C CONFIGURATION

001013A03R05 1 04

The Kits and configurations applicable to these MSNs are given at the end of this list

0354 0357 0393-0394 0411 0415 0443-0444 0447 0476 0478

KIT No. QTY PER A/C CONFIGURATION

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 5

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

001013A04R08 1 05

The Kits and configurations applicable to these MSNs are given at the end of this list

0525

KIT No. QTY PER A/C CONFIGURATION

001013A05R05 1 06

The Kits and configurations applicable to these MSNs are given at the end of this list

0138 0148 0496 0527 0543 0565 0661 1156 1235

KIT No. QTY PER A/C CONFIGURATION

001013A05R05 1 07

The Kits and configurations applicable to these MSNs are given at the end of this list

0455 0471

KIT No. QTY PER A/C CONFIGURATION

001013A06R00 1 08

The Kits and configurations applicable to these MSNs are given at the end of this list

0951 0999 1138 1168 1217 1226

KIT No. QTY PER A/C CONFIGURATION

001013A07R00 1 09

The Kits and configurations applicable to these MSNs are given at the end of this list

0667

KIT No. QTY PER A/C CONFIGURATION

001013A07R00 1 11

The Kits and configurations applicable to these MSNs are given at the end of this list

0142 0726

KIT No. QTY PER A/C CONFIGURATION

001013A08R00 1 10

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 6

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

NOTE : Config. 01 concerns the replacement of the tyre pressure placards for
aircraft with metric units, with 46X17-R20 Main Landing Gear (MLG)
tyres, and with Tyre Pressure Indicating System (TPIS) installed.

NOTE : Config. 02 concerns the replacement of the tyre pressure placards for
aircraft with metric units, with 46X17-R20 Main Landing Gear (MLG)
tyres, and without Tyre Pressure Indicating System (TPIS).

NOTE : Config. 03 concerns the replacement of the tyre pressure placards for
aircraft with US units, with 49X17-20 Main Landing Gear (MLG) tyres,
and without Tyre Pressure Indicating System (TPIS).

NOTE : Config. 04 concerns the replacement of the tyre pressure placards for
aircraft with metric units, with 45X16-R20 Main Landing Gear (MLG)
tyres, and without Tyre Pressure Indicating System (TPIS).

NOTE : Config. 05 concerns the replacement of the tyre pressure placards for
aircraft with metric units, with 49X17-20 Main Landing Gear (MLG) tyres,
and without Tyre Pressure Indicating System (TPIS).

NOTE : Config. 06 concerns the replacement of the tyre pressure placards for
aircraft with US units, with 46X17-R20 Main Landing Gear (MLG) tyres,
and with Tyre Pressure Indicating System (TPIS) installed.

NOTE : Config. 07 concerns the replacement of the tyre pressure placards for
aircraft with US units, with 46X17-R20 Main Landing Gear (MLG) tyres,
and without Tyre Pressure Indicating System (TPIS).

NOTE : Config. 08 concerns the replacement of the tyre pressure placards for
aircraft with US units, with 46X17-R20 Main Landing Gear (MLG) and
without Tyre Pressure Indicating System (TPIS).

NOTE : Config. 09 concerns the replacement of the tyre pressure placards for
aircraft with metric units, with 49X18-22 Main Landing Gear (MLG) tyres,
and with Tyre Pressure Indicating System (TPIS) installed.

NOTE : Config. 10 concerns the replacement of the tyre pressure placards for
aircraft with metric units, with 49X19-20 Main Landing Gear (MLG) tyres,
and without Tyre Pressure Indicating System (TPIS).

NOTE : Config. 11 concerns the replacement of the tyre pressure placards for
aircraft with metric units, with 49X18-22 Main Landing Gear (MLG) tyres,
and without Tyre Pressure Indicating System (TPIS).

(3) Spares

None

B. CONCURRENT REQUIREMENTS

For MSN 0204 0215 0244 0525

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 7

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment of

the following Service Bulletin(s) :

Service Bulletin No. A320-00-1019

For MSN 2540 2596 2623 3040

Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment of

the following Service Bulletin(s) :

Service Bulletin No. A320-00-1203

For MSN 0138 0148

Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment of

the following Service Bulletin(s) :

Service Bulletin No. A320-00-1206

For MSN 0087 0088 0112 0132 0140 0142 0157 0163 0164 0168 0169 0174 0175 0179 0183
0186 0187 0189 0190 0193 0203 0210 0220-0222 0228 0230-0235 0242 0243 0248-0251
0253-0256 0265 0277 0279 0283 0284 0288-0290 0293-0295 0299 0301 0302 0305 0309-0311
0316 0324 0325 0330 0331 0333-0335 0341-0343 0345 0348-0350 0354 0357 0359 0362 0375
0378 0384 0391-0395 0403 0404 0407 0411 0414 0415 0419 0420 0421 0424-0426 0428-0430
0436 0437-0438 0440 0441 0443 0444 0447-0449 0453 0455 0459-0461 0466 0471 0476 0478
0496 0497 0527 0537 0543 0565 0569 0580 0640 0661 0667 0676 0726 0768 0776 0795 0870
0934 0951 0999 1054 1063 1137 1138 1150 1156 1168 1189 1200 1217 1226 1235 1379 1411
1413 1439 1450 1454 1473 1478 1480 1484 1489 1697 1719 1732 1864 1874 1924 1949 2016
2158 2166 2278 2349 2390 2425 3769 3883

Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment of

the following Service Bulletin(s) :

Service Bulletin No. None

C. REASON

(1) History

This Service Bulletin is issued further to an operator’s request.

(2) Objective/Action

This Service Bulletin certifies A320-200 aircraft at the following weights :

- Maximum Take Off Weight (MTOW) is increased from 73.5 T or 75.5 T to 77.0 T

- Maximum Landing Weight (MLW) remains unchanged at 64.5 T

- Maximum Zero Fuel Weight (MZFW) remains unchanged at :

. 60.5 T for aircraft on which Mod. No. 23900K3471 (INCREASE DESIGN WEIGHT TO
61 T MZFW) is not embodied
DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 8

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

. 61.0 T for aircraft on which Mod. No. 23900K3471 (INCREASE DESIGN WEIGHT TO
61 T MZFW) or Service Bulletin No. A320-00-1030 is embodied.

This Service Bulletin also replaces the tyre pressure placards on the Main Landing Gear
(MLG) and on the Nose Landing Gear (NLG) to show the new MTOW and the related
tyre pressure.

(3) Advantages

Accomplishment of this Service Bulletin will satisfy the operator’s request.

(4) Operational/Maintenance Consequences

- The operational/maintenance consequences of this Service Bulletin are covered by the

update of the affected publications detailed in PLANNING INFORMATION paragraph K.

- This Service Bulletin is based on the aircraft configuration as known by AIRBUS (first
aircraft delivery configuration and modified by the reported incorporation of AIRBUS
Service Bulletins).

Prior to Service Bulletin embodiment, the operator is reminded to pay specific attention
to structural damage which may exist and to repairs which were performed on the aircraft
because they may be affected by the Service Bulletin. Operators must verify that all
allowable damage limits and repairs performed (both in accordance with the SRM
and outside of the SRM) are still applicable and effective to the new Service Bulletin
configuration. There may be additional or modified maintenance requirements, such
as temporary limits or additional inspections, that apply with respect to the Service
Bulletin configuration.

AIRBUS disclaims any liability for the effect which the Service Bulletin may have on
repairs performed on the aircraft before embodiment of the Service Bulletin.

If the post Service Bulletin repair status is no more covered by the SRM and for repairs
outside of the SRM covered by a RAS issued by AIRBUS, the operator should contact
AIRBUS Customer Services Repair Engineering Support (SEER). Repair review will be
done by AIRBUS at conditions of the Customer Services Catalogue.

D. DESCRIPTION

To accomplish this Service Bulletin it is necessary to :

(1) Config. 01

(a) Replace the tyre pressure placards on the NLG

(b) Replace the tyre pressure placards on the MLG

(c) Modify the wiring in the FWD Electronics Rack 90VU

(2) Config. 02

(a) Replace the tyre pressure placards on the NLG

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 9

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

(b) Replace the tyre pressure placards on the MLG

(3) Config. 03

(a) Replace the tyre pressure placards on the NLG

(b) Replace the tyre pressure placards on the MLG

(4) Config. 04

(a) Replace the tyre pressure placards on the NLG

(b) Replace the tyre pressure placards on the MLG

(5) Config. 05

(a) Replace the tyre pressure placards on the NLG

(b) Replace the tyre pressure placards on the MLG

(6) Config. 06

(a) Replace the tyre pressure placards on the NLG

(b) Replace the tyre pressure placards on the MLG

(c) Modify the wiring in the FWD Electronics Rack 90VU

(7) Config. 07

(a) Replace the tyre pressure placards on the NLG

(b) Replace the tyre pressure placards on the MLG

(8) Config. 08

(a) Install the tyre pressure placards on the MLG

(9) Config. 09

(a) Replace the tyre pressure placards on the NLG

(b) Replace the tyre pressure placards on the MLG

(c) Modify the wiring in the FWD Electronics Rack 90VU

(10) Config. 10

(a) Replace the tyre pressure placards on the NLG

(b) Replace the tyre pressure placards on the MLG

(11) Config. 11
DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 10

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

(a) Replace the tyre pressure placards on the NLG

(b) Replace the tyre pressure placards on the MLG

E. COMPLIANCE

(1) Classification

Optional

(2) Accomplishment Timescale

In accordance with operators’ maintenance schedule.

F. APPROVAL

Approved under EASA Design Organisation Approval No. EASA.21J.031.

If an aircraft listed in the effectivity has a modification or repair embodied that is not of AIRBUS
origin, and which affects the content of this Service Bulletin, the operator is responsible for
obtaining approval by its airworthiness authority for any adaptation necessary before incorporation
of the Service Bulletin.

G. MANPOWER

The manpower estimates given in this Service Bulletin are based on the direct labor cost to do the
work. These estimates assume that the work will be done by experienced personnel, and may
need to be revised upwards to suit operators’ circumstances. The estimates do not include the
time to prepare, plan or inspect the work. Manufacture and procurement of parts and tools, drying
times for paints, sealants, etc., and general administration work are also not included.

Config. 01 , Config. 06 , Config. 09

Get access 0.5

Replace the placards 1.0

Modify the wiring 0.5

Test 0.5

Close-up 0.5

TOTAL MANHOURS 3.0

ELAPSED TIME (HOURS) 3.0

Config. 02 thru Config. 05 , Config. 07 , Config. 10 thru Config. 11

Replace the placards 1.0

TOTAL MANHOURS 1.0

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 11

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

ELAPSED TIME (HOURS) 1.0

Config. 08

Replace the placards 0.5

TOTAL MANHOURS 0.5

ELAPSED TIME (HOURS) 0.5

H. WEIGHT AND BALANCE

Not changed

I. ELECTRICAL LOAD DATA

Not changed

J. REFERENCES

Aircraft Maintenance Manual (AMM) : 12-14-32 12-34-24 24-41-00 26-17-34

31-32-00 32-31-71 32-41-00 32-42-34
32-49-00 32-49-34 52-10-00 52-41-00

Consumable Material List (CML)

Elec. Std. Practices Manual (ESPM) : 20-33-00 20-52-21 20-55-00

Service Bulletin No. A320-00-1019

Service Bulletin No. A320-00-1030

Service Bulletin No. A320-00-1203

Service Bulletin No. A320-00-1206

Service Bulletin No. A320-32-1007

K. PUBLICATIONS AFFECTED

Aircraft Maintenance Manual (AMM) : 11-22-32 12-14-32 32-41-00

Illustrated Parts Catalog (IPC) : 11-22-32

Aircraft Schematic Manual (ASM) : 32-49-00

Aircraft Wiring Manual (AWM) : 32-49-05

Weight and Balance Manual (WBM) : Chapter LIMITATIONS

Flight Manual (FM)

Flight Crew Operating Manual (FCOM) : Vol. 3

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 12

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

This Service Bulletin has an operational impact. Please inform AIRBUS, at least four weeks in
advance, in case you need your operational documentation to be amended by an intermediate
revision prior to SB embodiment.

For this purpose, please request the intermediate revision by fax, telex or mail to :

SEDCC, AIRBUS - Customer Services Directorate

Fax No. 33 (0) 5 61 93 28 06
Sita No. TLSBP7X
E-mail [email protected]

These amendments will be confirmed by the next normal revision of operational documentation,
once your Service Bulletin accomplishment report has been sent, as usual, to our Customer
Services Directorate (SEDCC).

L. INTERCHANGEABILITY/MIXABILITY

Not applicable

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 13

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

This Page Intentionally Left Blank

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 14

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

2. MATERIAL INFORMATION

A. MATERIAL - PRICE AND AVAILABILITY

(1) Material

The Material Kit is included in the commercial offer of the Letter Agreement, and as such
will be supplied by AIRBUS Upgrade Services.

To facilitate the Material Kit reception, Airline Customers are requested to send a Customer
Purchase Order to :

AIRBUS UPGRADE SERVICES

Attn FCO Manager

(2) Price and Availability

Sales terms must be agreed between the Customers and AIRBUS in accordance with the
RFC (or RFC/RMO) procedure.

B. INDUSTRY SUPPORT INFORMATION

Refer to paragraph 2.A.(2): Price and Availability.

C. LIST OF COMPONENTS

Kit 001013A01R21

ITEM NEW PART No. QTY UM KEYWORD ITEM OLD PART No. INT INST DISP

1 D1121005027000 2 Placard (1) D1121005023400

D1121005026000
2 D1121005027800 2 Placard (2) D1121005023500
D1121005025900

Kit 001013A02R06

ITEM NEW PART No. QTY UM KEYWORD ITEM OLD PART No. INT INST DISP

5 D1121005026800 2 Placard (5) D1121005023700

D1121005026100
6 D1121005027700 2 Placard (6) D1121005024300
D1121005026500

Kit 001013A03R05

ITEM NEW PART No. QTY UM KEYWORD ITEM OLD PART No. INT INST DISP

1 D1121005027000 2 Placard (1) D1121005023400

D1121005026000
7 D1121005027300 2 Placard (7) D1121005024800

Kit 001013A04R08
DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 15

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

ITEM NEW PART No. QTY UM KEYWORD ITEM OLD PART No. INT INST DISP

1 D1121005027000 2 Placard (1) D1121005023400

D1121005026000
3 D1121005027600 2 Placard (3) D1121005026600

Kit 001013A05R05

ITEM NEW PART No. QTY UM KEYWORD ITEM OLD PART No. INT INST DISP

5 D1121005026800 2 Placard (5) D1121005023700

D1121005026100
8 D1121005027400 2 Placard (8) D1121005026900
D1121005026200
D1121005023800

Kit 001013A06R00

ITEM NEW PART No. QTY UM KEYWORD ITEM OLD PART No. INT INST DISP

8 D1121005027400 2 Placard (8) D1121005026900

D1121005026200
D1121005023800

Kit 001013A07R00

ITEM NEW PART No. QTY UM KEYWORD ITEM OLD PART No. INT INST DISP

1 D1121005027000 2 Placard (1) D1121005023400

D1121005026000
4 D1121005028500 2 Placard (4) D1121005027900

Kit 001013A08R00

ITEM NEW PART No. QTY UM KEYWORD ITEM OLD PART No. INT INST DISP

1 D1121005027000 2 Placard (1) D1121005023400

D1121005026000
9 D0041044620400 2 Placard (9) D1121005023600
D0041044620000

D. LIST OF MATERIALS - OPERATOR SUPPLIED

(1) Consumable Materials

DESCRIPTION REFERENCE TO CML QTY PER A/C INST/DISP

MAT No.

Internal Polyurethane Varnish Mat. No. 07-017 As required

Epoxy Adhesive Mat. No. 08-010 As required
Corrosion Inhibiting Fillet Mat. No. 09-016 As required
Consistency
Solvent General Purpose Mat. No. 11-026 As required
DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 16

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

DESCRIPTION REFERENCE TO CML QTY PER A/C INST/DISP

MAT No.

Lint-Free Cotton Cloth Mat. No. 19-003 As required

(2) Components

None

E. PARTS TO BE RE-IDENTIFIED BY THE OPERATOR

None

F. TOOLING - PRICE AND AVAILABILITY

None

G. SPECIAL TOOLS

None

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 17

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

This Page Intentionally Left Blank

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 18

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

3. ACCOMPLISHMENT INSTRUCTIONS

A. GENERAL

WARNING : MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.

CAUTION : ALWAYS OBEY THE PRECAUTIONS THAT FOLLOW TO KEEP ELECTRICAL

WIRING IN A SATISFACTORY CONDITION (ELECTRICALLY AND MECHANICALLY
SERVICEABLE). WHEN YOU DO MAINTENANCE WORK, REPAIRS OR
MODIFICATIONS, ALWAYS KEEP ELECTRICAL WIRING, COMPONENTS AND
THE WORK AREA AS CLEAN AS POSSIBLE. TO DO THIS:

- PUT PROTECTION, SUCH AS PLASTIC SHEETING, CLOTHS, ETC. AS

NECESSARY ON WIRING AND COMPONENTS

- REGULARLY REMOVE ALL SHAVINGS, UNWANTED MATERIAL AND OTHER

CONTAMINATION.

THESE PRECAUTIONS WILL DECREASE THE RISK OF CONTAMINATION AND

DAMAGE TO THE ELECTRICAL WIRING INSTALLATION.

IF THERE IS CONTAMINATION, REFER TO ESPM 20-55-00.

(1) Preparation

(a) Config. 01 , Config. 06 , Config. 09

1 Make sure that the aircraft is electrically grounded (Refer to AMM 12-34-24,
Page block 201).

2 Put the access platform(s) in position.

3 Open the passenger/crew door 831 (Refer to AMM 52-10-00, Page block 201).

4 Open the avionics door 811 (Refer to AMM 52-41-00, Page block 201).

5 Open, safety and tag this circuit breaker :

PANEL DESIGNATION FIN LOCATION

121VU HYDRAULIC/TYRE/PRESS 1GV 31 M

(b) Config. 02 thru Config. 05 , Config. 07 , Config. 08 , Config. 10 thru Config. 11

1 Make sure that the aircraft is electrically grounded (Refer to AMM 12-34-24,
Page block 201).

(2) Standard Practices

(a) For the specification of the materials (Mat. No.) that you must use in this Service
Bulletin, refer to Consumable Materials List (CML).

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 19

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

(b) Use a nonmetallic spatula to remove the adhesive.

(c) Clean the work area with Solvent General Purpose (Mat. No. 11-026) and a
Lint-Free Cotton Cloth (Mat. No. 19-003).

(d) Do a continuity test of the modified wires (Refer to ESPM 20-52-21).

(e) Obey the instructions for the general installation of electrical wire harnesses (Refer
to ESPM 20-33-00).

B. MODIFICATION

(1) Config. 01

NOTE : Make sure that the Nose Landing Gear (NLG) and Main Landing Gear (MLG)
tyres are approved for 77.0T Maximum Take Off Weight (MTOW) operations
in relation to Service Bulletin No. A320-32-1007.

(a) Replace the tyre pressure placards on the NLG

Refer to Kit 001013A01R21
Refer to Figure 1

1 Remove :
2 Placard D1121005023400 Item (1)

or

2 Placard D1121005026000 Item (1)

2 Use a nonmetallic scraper, Solvent General Purpose (Mat. No. 11-026) and a
Lint-Free Cotton Cloth (Mat. No. 19-003) to remove the unwanted adhesive
from the NLG.

3 Clean the surfaces of the placards to which you will apply the adhesive with
Solvent General Purpose (Mat. No. 11-026) and a Lint-Free Cotton Cloth
(Mat. No. 19-003).

4 Install :
2 Placard D1121005027000 Item 1

5 Bond the placards with Two Component Epoxy Adhesive (Mat. No. 08-010).

6 Apply a fillet of Corrosion Inhibiting Fillet Consistency (Mat. No. 09-016) around
the edges of the placards, Item 1, and let the sealant dry.

7 Remove the unwanted sealant with Solvent General Purpose (Mat. No. 11-026)
and a Lint-Free Cotton Cloth (Mat. No. 19-003).

8 Apply Internal Polyurethane Varnish (Mat. No. 07-017) as a protection to

the placards, Item 1.

(b) Replace the tyre pressure placards on the MLG

Refer to Kit 001013A01R21
DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 20

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

Refer to Figure 2

1 Remove :
2 Placard D1121005023500 Item (2)

or

2 Placard D1121005025900 Item (2)

2 Use a nonmetallic scraper, Solvent General Purpose (Mat. No. 11-026) and a
Lint-Free Cotton Cloth (Mat. No. 19-003) to remove the unwanted adhesive
from the MLG.

3 Clean the surfaces of the placards to which you will apply the adhesive with
Solvent General Purpose (Mat. No. 11-026) and a Lint-Free Cotton Cloth
(Mat. No. 19-003).

4 Install :
2 Placard D1121005027800 Item 2

5 Bond the placards with Two Component Epoxy Adhesive (Mat. No. 08-010).

6 Apply a fillet of Corrosion Inhibiting Fillet Consistency (Mat. No. 09-016) around
the edges of the placards, Item 2, and let the sealant dry.

7 Remove the unwanted sealant with Solvent General Purpose (Mat. No. 11-026)
and a Lint-Free Cotton Cloth (Mat. No. 19-003).

8 Apply Internal Polyurethane Varnish (Mat. No. 07-017) as a protection to

the placards, Item 2.

(c) Modify the wiring in the FWD Electronics Rack 90VU

Refer to Figures 10, 11
(Refer to AMM 26-17-34, Page block 401)
(Refer to AMM 32-31-71, Page block 401)
(Refer to AMM 32-42-34, Page block 401)
(Refer to AMM 32-49-34, Page block 401)

1 Remove all the computers installed on the Shelf 94VU :

(Refer to AMM 26-17-34, Page block 401)
(Refer to AMM 32-31-71, Page block 401)
(Refer to AMM 32-42-34, Page block 401)
(Refer to AMM 32-49-34, Page block 401)

FIN 10WQ

1 SDCU Retain

FIN 5GA2

1 LGCIU Retain

FIN 10GG
DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 21

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

1 BSCU Retain

FIN 2GV

1 TPIS Retain

NOTE : You must install these computers again in ACCOMPLISHMENT

INSTRUCTIONS paragraph B.(1)(c) 10.

2 Disconnect the bonding braid.

3 Remove the attachment hardware from the shelf.

NOTE : Retain the hardware.

4 Remove the Shelf 94VU.

5 For aircraft with 46X16-20 or 46X17-R20 tyres installed

a Modify the connection of the wires shown on the lines 1 thru 4 (Refer
to Figure 11).

6 Install the Shelf 94VU on aircraft.

7 Do the electrical bonding on the shelf attachment.

8 Attach the Shelf 94VU and connect the bonding braid with the hardware retained
in ACCOMPLISHMENT INSTRUCTIONS paragraph B.(1)(c) 3.

9 Connect the related connectors.

10 Install all the computers on the Shelf 94VU :

(Refer to AMM 26-17-34, Page block 401)
(Refer to AMM 32-31-71, Page block 401)
(Refer to AMM 32-42-34, Page block 401)
(Refer to AMM 32-49-34, Page block 401)

FIN 10WQ

1 SDCU

FIN 5GA2

1 LGCIU

FIN 10GG

1 BSCU

FIN 2GV

1 TPIS

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 22

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

NOTE : These computers were retained in ACCOMPLISHMENT

INSTRUCTIONS paragraph B.(1)(c) 1.

(2) Config. 02

NOTE : Make sure that the Nose Landing Gear (NLG) and Main Landing Gear (MLG)
tyres are approved for 77.0T Maximum Take Off Weight (MTOW) operations
in relation to Service Bulletin No. A320-32-1007.

(a) Replace the tyre pressure placards on the NLG

Refer to Kit 001013A01R21
Refer to Figure 1

1 Remove :
2 Placard D1121005023400 Item (1)

or

2 Placard D1121005026000 Item (1)

2 Use a nonmetallic scraper, Solvent General Purpose (Mat. No. 11-026) and a
Lint-Free Cotton Cloth (Mat. No. 19-003) to remove the unwanted adhesive
from the NLG.

3 Clean the surfaces of the placards to which you will apply the adhesive with
Solvent General Purpose (Mat. No. 11-026) and a Lint-Free Cotton Cloth
(Mat. No. 19-003).

4 Install :
2 Placard D1121005027000 Item 1

5 Bond the placards with Two Component Epoxy Adhesive (Mat. No. 08-010).

6 Apply a fillet of Corrosion Inhibiting Fillet Consistency (Mat. No. 09-016) around
the edges of the placards, Item 1, and let the sealant dry.

7 Remove the unwanted sealant with Solvent General Purpose (Mat. No. 11-026)
and a Lint-Free Cotton Cloth (Mat. No. 19-003).

8 Apply Internal Polyurethane Varnish (Mat. No. 07-017) as a protection to

the placards, Item 1.

(b) Replace the tyre pressure placards on the MLG

Refer to Kit 001013A01R21
Refer to Figure 2

1 Remove :
2 Placard D1121005023500 Item (2)

or

2 Placard D1121005025900 Item (2)

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 23

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

2 Use a nonmetallic scraper, Solvent General Purpose (Mat. No. 11-026) and a
Lint-Free Cotton Cloth (Mat. No. 19-003) to remove the unwanted adhesive
from the MLG.

3 Clean the surfaces of the placards to which you will apply the adhesive with
Solvent General Purpose (Mat. No. 11-026) and a Lint-Free Cotton Cloth
(Mat. No. 19-003).

4 Install :
2 Placard D1121005027800 Item 2

5 Bond the placards with Two Component Epoxy Adhesive (Mat. No. 08-010).

6 Apply a fillet of Corrosion Inhibiting Fillet Consistency (Mat. No. 09-016) around
the edges of the placards, Item 2, and let the sealant dry.

7 Remove the unwanted sealant with Solvent General Purpose (Mat. No. 11-026)
and a Lint-Free Cotton Cloth (Mat. No. 19-003).

8 Apply Internal Polyurethane Varnish (Mat. No. 07-017) as a protection to

the placards, Item 2.

(3) Config. 03

NOTE : Make sure that the Nose Landing Gear (NLG) and Main Landing Gear (MLG)
tyres are approved for 77.0T Maximum Take Off Weight (MTOW) operations
in relation to Service Bulletin No. A320-32-1007.

(a) Replace the tyre pressure placards on the NLG

Refer to Kit 001013A02R06
Refer to Figure 3

1 Remove :
2 Placard D1121005023700 Item (5)

or

2 Placard D1121005026100 Item (5)

2 Use a nonmetallic scraper, Solvent General Purpose (Mat. No. 11-026) and a
Lint-Free Cotton Cloth (Mat. No. 19-003) to remove the unwanted adhesive
from the NLG.

3 Clean the surfaces of the placards to which you will apply the adhesive with
Solvent General Purpose (Mat. No. 11-026) and a Lint-Free Cotton Cloth
(Mat. No. 19-003).

4 Install :
2 Placard D1121005026800 Item 5

5 Bond the placards with Two Component Epoxy Adhesive (Mat. No. 08-010).

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 24

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

6 Apply a fillet of Corrosion Inhibiting Fillet Consistency (Mat. No. 09-016) around
the edges of the placards, Item 5, and let the sealant dry.

7 Remove the unwanted sealant with Solvent General Purpose (Mat. No. 11-026)
and a Lint-Free Cotton Cloth (Mat. No. 19-003).

8 Apply Internal Polyurethane Varnish (Mat. No. 07-017) as a protection to

the placards, Item 5.

(b) Replace the tyre pressure placards on the MLG

Refer to Kit 001013A02R06
Refer to Figure 4

1 Remove :
2 Placard D1121005024300 Item (6)

or

2 Placard D1121005026500 Item (6)

2 Use a nonmetallic scraper, Solvent General Purpose (Mat. No. 11-026) and a
Lint-Free Cotton Cloth (Mat. No. 19-003) to remove the unwanted adhesive
from the MLG.

3 Clean the surfaces of the placards to which you will apply the adhesive with
Solvent General Purpose (Mat. No. 11-026) and a Lint-Free Cotton Cloth
(Mat. No. 19-003).

4 Install :
2 Placard D1121005027700 Item 6

5 Bond the placards with Two Component Epoxy Adhesive (Mat. No. 08-010).

6 Apply a fillet of Corrosion Inhibiting Fillet Consistency (Mat. No. 09-016) around
the edges of the placards, Item 6, and let the sealant dry.

7 Remove the unwanted sealant with Solvent General Purpose (Mat. No. 11-026)
and a Lint-Free Cotton Cloth (Mat. No. 19-003).

8 Apply Internal Polyurethane Varnish (Mat. No. 07-017) as a protection to

the placards, Item 6.

(4) Config. 04

NOTE : Make sure that the Nose Landing Gear (NLG) and Main Landing Gear (MLG)
tyres are approved for 77.0T Maximum Take Off Weight (MTOW) operations
in relation to Service Bulletin No. A320-32-1007.

(a) Replace the tyre pressure placards on the NLG

Refer to Kit 001013A03R05
Refer to Figure 1

1 Remove :
DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 25

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

2 Placard D1121005023400 Item (1)

or

2 Placard D1121005026000 Item (1)

2 Use a nonmetallic scraper, Solvent General Purpose (Mat. No. 11-026) and a
Lint-Free Cotton Cloth (Mat. No. 19-003) to remove the unwanted adhesive
from the NLG.

3 Clean the surfaces of the placards to which you will apply the adhesive with
Solvent General Purpose (Mat. No. 11-026) and a Lint-Free Cotton Cloth
(Mat. No. 19-003).

4 Install :
2 Placard D1121005027000 Item 1

5 Bond the placards with Two Component Epoxy Adhesive (Mat. No. 08-010).

6 Apply a fillet of Corrosion Inhibiting Fillet Consistency (Mat. No. 09-016) around
the edges of the placards, Item 1, and let the sealant dry.

7 Remove the unwanted sealant with Solvent General Purpose (Mat. No. 11-026)
and a Lint-Free Cotton Cloth (Mat. No. 19-003).

8 Apply Internal Polyurethane Varnish (Mat. No. 07-017) as a protection to

the placards, Item 1.

(b) Replace the tyre pressure placards on the MLG

Refer to Kit 001013A03R05
Refer to Figure 5

1 Remove :
2 Placard D1121005024800 Item (7)

2 Use a nonmetallic scraper, Solvent General Purpose (Mat. No. 11-026) and a
Lint-Free Cotton Cloth (Mat. No. 19-003) to remove the unwanted adhesive
from the MLG.

3 Clean the surfaces of the placards to which you will apply the adhesive with
Solvent General Purpose (Mat. No. 11-026) and a Lint-Free Cotton Cloth
(Mat. No. 19-003).

4 Install :
2 Placard D1121005027300 Item 7

5 Bond the placards with Two Component Epoxy Adhesive (Mat. No. 08-010).

6 Apply a fillet of Corrosion Inhibiting Fillet Consistency (Mat. No. 09-016) around
the edges of the placards, Item 7, and let the sealant dry.

7 Remove the unwanted sealant with Solvent General Purpose (Mat. No. 11-026)
and a Lint-Free Cotton Cloth (Mat. No. 19-003).
DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 26

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

8 Apply Internal Polyurethane Varnish (Mat. No. 07-017) as a protection to

the placards, Item 7.

(5) Config. 05

NOTE : Make sure that the Nose Landing Gear (NLG) and Main Landing Gear (MLG)
tyres are approved for 77.0T Maximum Take Off Weight (MTOW) operations
in relation to Service Bulletin No. A320-32-1007.

(a) Replace the tyre pressure placards on the NLG

Refer to Kit 001013A04R08
Refer to Figure 1

1 Remove :
2 Placard D1121005023400 Item (1)

or

2 Placard D1121005026000 Item (1)

2 Use a nonmetallic scraper, Solvent General Purpose (Mat. No. 11-026) and a
Lint-Free Cotton Cloth (Mat. No. 19-003) to remove the unwanted adhesive
from the NLG.

3 Clean the surfaces of the placards to which you will apply the adhesive with
Solvent General Purpose (Mat. No. 11-026) and a Lint-Free Cotton Cloth
(Mat. No. 19-003).

4 Install :
2 Placard D1121005027000 Item 1

5 Bond the placards with Two Component Epoxy Adhesive (Mat. No. 08-010).

6 Apply a fillet of Corrosion Inhibiting Fillet Consistency (Mat. No. 09-016) around
the edges of the placards, Item 1, and let the sealant dry.

7 Remove the unwanted sealant with Solvent General Purpose (Mat. No. 11-026)
and a Lint-Free Cotton Cloth (Mat. No. 19-003).

8 Apply Internal Polyurethane Varnish (Mat. No. 07-017) as a protection to

the placards, Item 1.

(b) Replace the tyre pressure placards on the MLG

Refer to Kit 001013A04R08
Refer to Figure 6

1 Remove :
2 Placard D1121005026600 Item (3)

2 Use a nonmetallic scraper, Solvent General Purpose (Mat. No. 11-026) and a
Lint-Free Cotton Cloth (Mat. No. 19-003) to remove the unwanted adhesive
from the MLG.

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 27

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

3 Clean the surfaces of the placards to which you will apply the adhesive with
Solvent General Purpose (Mat. No. 11-026) and a Lint-Free Cotton Cloth
(Mat. No. 19-003).

4 Install :
2 Placard D1121005027600 Item 3

5 Bond the placards with Two Component Epoxy Adhesive (Mat. No. 08-010).

6 Apply a fillet of Corrosion Inhibiting Fillet Consistency (Mat. No. 09-016) around
the edges of the placards, Item 3, and let the sealant dry.

7 Remove the unwanted sealant with Solvent General Purpose (Mat. No. 11-026)
and a Lint-Free Cotton Cloth (Mat. No. 19-003).

8 Apply Internal Polyurethane Varnish (Mat. No. 07-017) as a protection to

the placards, Item 3.

(6) Config. 06

NOTE : Make sure that the Nose Landing Gear (NLG) and Main Landing Gear (MLG)
tyres are approved for 77.0T Maximum Take Off Weight (MTOW) operations
in relation to Service Bulletin No. A320-32-1007.

(a) Replace the tyre pressure placards on the NLG

Refer to Kit 001013A05R05
Refer to Figure 3

1 Remove :
2 Placard D1121005023700 Item (5)

or

2 Placard D1121005026100 Item (5)

2 Use a nonmetallic scraper, Solvent General Purpose (Mat. No. 11-026) and a
Lint-Free Cotton Cloth (Mat. No. 19-003) to remove the unwanted adhesive
from the NLG.

3 Clean the surfaces of the placards to which you will apply the adhesive with
Solvent General Purpose (Mat. No. 11-026) and a Lint-Free Cotton Cloth
(Mat. No. 19-003).

4 Install :
2 Placard D1121005026800 Item 5

5 Bond the placards with Two Component Epoxy Adhesive (Mat. No. 08-010).

6 Apply a fillet of Corrosion Inhibiting Fillet Consistency (Mat. No. 09-016) around
the edges of the placards, Item 5, and let the sealant dry.

7 Remove the unwanted sealant with Solvent General Purpose (Mat. No. 11-026)
and a Lint-Free Cotton Cloth (Mat. No. 19-003).
DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 28

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

8 Apply Internal Polyurethane Varnish (Mat. No. 07-017) as a protection to

the placards, Item 5.

(b) Replace the tyre pressure placards on the MLG

Refer to Kit 001013A05R05
Refer to Figure 7

1 Remove :
2 Placard D1121005026200 Item (8)

or

2 Placard D1121005026900 Item (8)

or

2 Placard D1121005023800 Item (8)

2 Use a nonmetallic scraper, Solvent General Purpose (Mat. No. 11-026) and a
Lint-Free Cotton Cloth (Mat. No. 19-003) to remove the unwanted adhesive
from the MLG.

3 Clean the surfaces of the placards to which you will apply the adhesive with
Solvent General Purpose (Mat. No. 11-026) and a Lint-Free Cotton Cloth
(Mat. No. 19-003).

4 Install :
2 Placard D1121005027400 Item 8

5 Bond the placards with Two Component Epoxy Adhesive (Mat. No. 08-010).

6 Apply a fillet of Corrosion Inhibiting Fillet Consistency (Mat. No. 09-016) around
the edges of the placards, Item 8, and let the sealant dry.

7 Remove the unwanted sealant with Solvent General Purpose (Mat. No. 11-026)
and a Lint-Free Cotton Cloth (Mat. No. 19-003).

8 Apply Internal Polyurethane Varnish (Mat. No. 07-017) as a protection to

the placards, Item 8.

(c) Modify the wiring in the FWD Electronics Rack 90VU

Refer to Figures 10, 11
(Refer to AMM 26-17-34, Page block 401)
(Refer to AMM 32-31-71, Page block 401)
(Refer to AMM 32-42-34, Page block 401)
(Refer to AMM 32-49-34, Page block 401)

1 Remove all the computers installed on the Shelf 94VU :

(Refer to AMM 26-17-34, Page block 401)
(Refer to AMM 32-31-71, Page block 401)
(Refer to AMM 32-42-34, Page block 401)
(Refer to AMM 32-49-34, Page block 401)

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 29

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

FIN 10WQ

1 SDCU Retain

FIN 5GA2

1 LGCIU Retain

FIN 10GG

1 BSCU Retain

FIN 2GV

1 TPIS Retain

NOTE : You must install these computers again in ACCOMPLISHMENT

INSTRUCTIONS paragraph B.(6)(c) 10.

2 Disconnect the bonding braid.

3 Remove the attachment hardware from the shelf.

NOTE : Retain the hardware.

4 Remove the Shelf 94VU.

5 For aircraft with 46X16-20 or 46X17-R20 tyres installed

a Modify the connection of the wires shown on the lines 1 thru 4 (Refer
to Figure 11).

6 Install the Shelf 94VU on aircraft.

7 Do the electrical bonding on the shelf attachment.

8 Attach the Shelf 94VU and connect the bonding braid with the hardware retained
in ACCOMPLISHMENT INSTRUCTIONS paragraph B.(6)(c) 3.

9 Connect the related connectors.

10 Install all the computers on the Shelf 94VU :

(Refer to AMM 26-17-34, Page block 401)
(Refer to AMM 32-31-71, Page block 401)
(Refer to AMM 32-42-34, Page block 401)
(Refer to AMM 32-49-34, Page block 401)

FIN 10WQ

1 SDCU

FIN 5GA2

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 30

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

1 LGCIU

FIN 10GG

1 BSCU

FIN 2GV

1 TPIS

NOTE : These computers were retained in ACCOMPLISHMENT

INSTRUCTIONS paragraph B.(6)(c) 1.

(7) Config. 07

NOTE : Make sure that the Nose Landing Gear (NLG) and Main Landing Gear (MLG)
tyres are approved for 77.0T Maximum Take Off Weight (MTOW) operations
in relation to Service Bulletin No. A320-32-1007.

(a) Replace the tyre pressure placards on the NLG

Refer to Kit 001013A05R05
Refer to Figure 3

1 Remove :
2 Placard D1121005023700 Item (5)

or

2 Placard D1121005026100 Item (5)

2 Use a nonmetallic scraper, Solvent General Purpose (Mat. No. 11-026) and a
Lint-Free Cotton Cloth (Mat. No. 19-003) to remove the unwanted adhesive
from the NLG.

3 Clean the surfaces of the placards to which you will apply the adhesive with
Solvent General Purpose (Mat. No. 11-026) and a Lint-Free Cotton Cloth
(Mat. No. 19-003).

4 Install :
2 Placard D1121005026800 Item 5

5 Bond the placards with Two Component Epoxy Adhesive (Mat. No. 08-010).

6 Apply a fillet of Corrosion Inhibiting Fillet Consistency (Mat. No. 09-016) around
the edges of the placards, Item 5, and let the sealant dry.

7 Remove the unwanted sealant with Solvent General Purpose (Mat. No. 11-026)
and a Lint-Free Cotton Cloth (Mat. No. 19-003).

8 Apply Internal Polyurethane Varnish (Mat. No. 07-017) as a protection to

the placards, Item 5.

(b) Replace the tyre pressure placards on the MLG

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 31

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

Refer to Kit 001013A05R05

Refer to Figures 7

1 Remove :
2 Placard D1121005026200 Item (8)

or

2 Placard D1121005026900 Item (8)

or

2 Placard D1121005023800 Item (8)

2 Use a nonmetallic scraper, Solvent General Purpose (Mat. No. 11-026) and a
Lint-Free Cotton Cloth (Mat. No. 19-003) to remove the unwanted adhesive
from the MLG.

3 Clean the surfaces of the placards to which you will apply the adhesive with
Solvent General Purpose (Mat. No. 11-026) and a Lint-Free Cotton Cloth
(Mat. No. 19-003).

4 Install :
2 Placard D1121005027400 Item 8

5 Bond the placards with Two Component Epoxy Adhesive (Mat. No. 08-010).

6 Apply a fillet of Corrosion Inhibiting Fillet Consistency (Mat. No. 09-016) around
the edges of the placards, Item 8, and let the sealant dry.

7 Remove the unwanted sealant with Solvent General Purpose (Mat. No. 11-026)
and a Lint-Free Cotton Cloth (Mat. No. 19-003).

8 Apply Internal Polyurethane Varnish (Mat. No. 07-017) as a protection to

the placards, Item 8.

(8) Config. 08

NOTE : Make sure that the Nose Landing Gear (NLG) and Main Landing Gear (MLG)
tyres are approved for 77.0T Maximum Take Off Weight (MTOW) operations
in relation to Service Bulletin No. A320-32-1007.

(a) Replace the tyre pressure placards on the MLG

Refer to Kit 001013A06R00
Refer to Figure 7

1 Remove :
2 Placard D1121005026200 Item (8)

or

2 Placard D1121005026900 Item (8)

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 32

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

or

2 Placard D1121005023800 Item (8)

2 Use a nonmetallic scraper, Solvent General Purpose (Mat. No. 11-026) and a
Lint-Free Cotton Cloth (Mat. No. 19-003) to remove the unwanted adhesive
from the MLG.

3 Clean the surfaces of the placards to which you will apply the adhesive with
Solvent General Purpose (Mat. No. 11-026) and a Lint-Free Cotton Cloth
(Mat. No. 19-003).

4 Install :
2 Placard D1121005027400 Item 8

5 Bond the placards with Two Component Epoxy Adhesive (Mat. No. 08-010).

6 Apply a fillet of Corrosion Inhibiting Fillet Consistency (Mat. No. 09-016) around
the edges of the placards, Item 8, and let the sealant dry.

7 Remove the unwanted sealant with Solvent General Purpose (Mat. No. 11-026)
and a Lint-Free Cotton Cloth (Mat. No. 19-003).

8 Apply Internal Polyurethane Varnish (Mat. No. 07-017) as a protection to

the placards, Item 8.

(9) Config. 09

NOTE : Make sure that the Nose Landing Gear (NLG) and Main Landing Gear (MLG)
tyres are approved for 77.0T Maximum Take Off Weight (MTOW) operations
in relation to Service Bulletin No. A320-32-1007.

(a) Replace the tyre pressure placards on the NLG

Refer to Kit 001013A07R00
Refer to Figure 1

1 Remove :
2 Placard D1121005023400 Item (1)

or

2 Placard D1121005026000 Item (1)

2 Use a nonmetallic scraper, Solvent General Purpose (Mat. No. 11-026) and a
Lint-Free Cotton Cloth (Mat. No. 19-003) to remove the unwanted adhesive
from the NLG.

3 Clean the surfaces of the placards to which you will apply the adhesive with
Solvent General Purpose (Mat. No. 11-026) and a Lint-Free Cotton Cloth
(Mat. No. 19-003).

4 Install :
2 Placard D112005027000 Item 1
DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 33

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

5 Bond the placards with Two Component Epoxy Adhesive (Mat. No. 08-010).

6 Apply a fillet of Corrosion Inhibiting Fillet Consistency (Mat. No. 09-016) around
the edges of the placards, Item 1, and let the sealant dry.

7 Remove the unwanted sealant with Solvent General Purpose (Mat. No. 11-026)
and a Lint-Free Cotton Cloth (Mat. No. 19-003).

8 Apply Internal Polyurethane Varnish (Mat. No. 07-017) as a protection to

the placards, Item 1.

(b) Replace the tyre pressure placards on the MLG

Refer to Kit 001013A07R00
Refer to Figure 8

1 Remove :
2 Placard D1121005027900 Item (4)

2 Use a nonmetallic scraper, Solvent General Purpose (Mat. No. 11-026) and a
Lint-Free Cotton Cloth (Mat. No. 19-003) to remove the unwanted adhesive
from the MLG.

3 Clean the surfaces of the placards to which you will apply the adhesive with
Solvent General Purpose (Mat. No. 11-026) and a Lint-Free Cotton Cloth
(Mat. No. 19-003).

4 Install :
2 Placard D1121005028500 Item 4

5 Bond the placards with Two Component Epoxy Adhesive (Mat. No. 08-010).

6 Apply a fillet of Corrosion Inhibiting Fillet Consistency (Mat. No. 09-016) around
the edges of the placards, Item 4, and let the sealant dry.

7 Remove the unwanted sealant with Solvent General Purpose (Mat. No. 11-026)
and a Lint-Free Cotton Cloth (Mat. No. 19-003).

8 Apply Internal Polyurethane Varnish (Mat. No. 07-017) as a protection to

the placards, Item 4.

(c) Modify the wiring in the FWD Electronics Rack 90VU

Refer to Figures 12, 13
(Refer to AMM 26-17-34, Page block 401)
(Refer to AMM 32-31-71, Page block 401)
(Refer to AMM 32-42-34, Page block 401)
(Refer to AMM 32-49-34, Page block 401)

1 Remove all the computers installed on the Shelf 94VU :

(Refer to AMM 26-17-34, Page block 401)
(Refer to AMM 32-31-71, Page block 401)
(Refer to AMM 32-42-34, Page block 401)
(Refer to AMM 32-49-34, Page block 401)

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 34

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

FIN 10WQ

1 SDCU Retain

FIN 5GA2

1 LGCIU Retain

FIN 10GG

1 BSCU Retain

FIN 2GV

1 TPIS Retain

NOTE : You must install these computers again in ACCOMPLISHMENT

INSTRUCTIONS paragraph B.(9)(c) 10.

2 Disconnect the bonding braid.

3 Remove the attachment hardware from the shelf.

NOTE : Retain the hardware.

4 Remove the Shelf 94VU.

5 For aircraft with 49X18-22 or 1270X455-R22 tyres installed

a Modify the connection of the wires shown on the lines 1 thru 4 (Refer
to Figure 13).

6 Install the Shelf 94VU on aircraft.

7 Do the electrical bonding on the shelf attachment.

8 Attach the Shelf 94VU and connect the bonding braid with the hardware retained
in ACCOMPLISHMENT INSTRUCTIONS paragraph B.(9)(c) 3.

9 Connect the related connectors.

10 Install all the computers on the Shelf 94VU :

(Refer to AMM 26-17-34, Page block 401)
(Refer to AMM 32-31-71, Page block 401)
(Refer to AMM 32-42-34, Page block 401)
(Refer to AMM 32-49-34, Page block 401)

FIN 10WQ

1 SDCU

FIN 5GA2

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 35

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

1 LGCIU

FIN 10GG

1 BSCU

FIN 2GV

1 TPIS

NOTE : These computers were retained in ACCOMPLISHMENT

INSTRUCTIONS paragraph B.(9)(c) 1.

(10) Config. 10

NOTE : Make sure that the Nose Landing Gear (NLG) and Main Landing Gear (MLG)
tyres are approved for 77.0T Maximum Take Off Weight (MTOW) operations
in relation to Service Bulletin No. A320-32-1007.

(a) Replace the tyre pressure placards on the NLG

Refer to Kit 001013A08R00
Refer to Figure 1

1 Remove :
2 Placard D1121005023400 Item (1)

or

2 Placard D1121005026000 Item (1)

2 Use a nonmetallic scraper, Solvent General Purpose (Mat. No. 11-026) and a
Lint-Free Cotton Cloth (Mat. No. 19-003) to remove the unwanted adhesive
from the NLG.

3 Clean the surfaces of the placards to which you will apply the adhesive with
Solvent General Purpose (Mat. No. 11-026) and a Lint-Free Cotton Cloth
(Mat. No. 19-003).

4 Install :
2 Placard D1121005027000 Item 1

5 Bond the placards with Two Component Epoxy Adhesive (Mat. No. 08-010).

6 Apply a fillet of Corrosion Inhibiting Fillet Consistency (Mat. No. 09-016) around
the edges of the placards, Item 1, and let the sealant dry.

7 Remove the unwanted sealant with Solvent General Purpose (Mat. No. 11-026)
and a Lint-Free Cotton Cloth (Mat. No. 19-003).

8 Apply Internal Polyurethane Varnish (Mat. No. 07-017) as a protection to

the placards, Item 1.

(b) Replace the tyre pressure placards on the MLG

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 36

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

Refer to Kit 001013A08R00

Refer to Figure 9

1 Remove :
2 Placard D1121005023600 Item (9)

or

2 Placard D0041044620000 Item (9)

2 Use a nonmetallic scraper, Solvent General Purpose (Mat. No. 11-026) and a
Lint-Free Cotton Cloth (Mat. No. 19-003) to remove the unwanted adhesive
from the MLG.

3 Clean the surfaces of the placards to which you will apply the adhesive with
Solvent General Purpose (Mat. No. 11-026) and a Lint-Free Cotton Cloth
(Mat. No. 19-003).

4 Install :
2 Placard D0041044620400 Item 9

5 Bond the placards with Two Component Epoxy Adhesive (Mat. No. 08-010).

6 Apply a fillet of Corrosion Inhibiting Fillet Consistency (Mat. No. 09-016) around
the edges of the placards, Item 9, and let the sealant dry.

7 Remove the unwanted sealant with Solvent General Purpose (Mat. No. 11-026)
and a Lint-Free Cotton Cloth (Mat. No. 19-003).

8 Apply Internal Polyurethane Varnish (Mat. No. 07-017) as a protection to

the placards, Item 9.

(11) Config. 11

NOTE : Make sure that the Nose Landing Gear (NLG) and Main Landing Gear (MLG)
tyres are approved for 77.0T Maximum Take Off Weight (MTOW) operations
in relation to Service Bulletin No. A320-32-1007.

(a) Replace the tyre pressure placards on the NLG

Refer to Kit 001013A07R00
Refer to Figure 1

1 Remove :
2 Placard D1121005023400 Item (1)

or

2 Placard D1121005026000 Item (1)

2 Use a nonmetallic scraper, Solvent General Purpose (Mat. No. 11-026) and a
Lint-Free Cotton Cloth (Mat. No. 19-003) to remove the unwanted adhesive
from the NLG.

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 37

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

3 Clean the surfaces of the placards to which you will apply the adhesive with
Solvent General Purpose (Mat. No. 11-026) and a Lint-Free Cotton Cloth
(Mat. No. 19-003).

4 Install :
2 Placard D1121005027000 Item 1

5 Bond the placards with Two Component Epoxy Adhesive (Mat. No. 08-010).

6 Apply a fillet of Corrosion Inhibiting Fillet Consistency (Mat. No. 09-016) around
the edges of the placards, Item 1, and let the sealant dry.

7 Remove the unwanted sealant with Solvent General Purpose (Mat. No. 11-026)
and a Lint-Free Cotton Cloth (Mat. No. 19-003).

8 Apply Internal Polyurethane Varnish (Mat. No. 07-017) as a protection to

the placards, Item 1.

(b) Replace the tyre pressure placards on the MLG

Refer to Kit 001013A07R00
Refer to Figure 8

1 Remove :
2 Placard D1121005027900 Item (4)

2 Use a nonmetallic scraper, Solvent General Purpose (Mat. No. 11-026) and a
Lint-Free Cotton Cloth (Mat. No. 19-003) to remove the unwanted adhesive
from the MLG.

3 Clean the surfaces of the placards to which you will apply the adhesive with
Solvent General Purpose (Mat. No. 11-026) and a Lint-Free Cotton Cloth
(Mat. No. 19-003).

4 Install :
2 Placard D1121005028500 Item 4

5 Bond the placards with Two Component Epoxy Adhesive (Mat. No. 08-010).

6 Apply a fillet of Corrosion Inhibiting Fillet Consistency (Mat. No. 09-016) around
the edges of the placards, Item 4, and let the sealant dry.

7 Remove the unwanted sealant with Solvent General Purpose (Mat. No. 11-026)
and a Lint-Free Cotton Cloth (Mat. No. 19-003).

8 Apply Internal Polyurethane Varnish (Mat. No. 07-017) as a protection to

the placards, Item 4.

C. TEST

(1) Config. 01 , Config. 06

(a) Job Set-up

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 38

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

1 Remove the safety clip and tag and close this circuit breaker :

PANEL DESIGNATION FIN LOCATION

121VU HYDRAULIC/TYRE/PRESS 1GV 31 M

2 Energize the aircraft electrical circuits (Refer to AMM 24-41-00, Page block 201).

(b) Tests

1 Do a functional test of the Tyre Pressure Indicating System (TPIS) (Refer

to AMM 32-49-00, Page block 501).

2 Do the test after the removal/installation of the Smoke Detection Control Unit
(SDCU) (10WQ) (Refer to AMM 26-17-34, Page block 401).

3 Do the test after the removal/installation of the Landing Gear Control and
Interface Unit (LGCIU) (5GA1, 5GA2) (Refer to AMM 32-31-71, Page block 401).

4 Do the test after the removal/installation of the Braking/Steering Control Unit

(BSCU) (10GG) (Refer to AMM 32-42-34, Page block 401).

5 Do a check of the pressure of the tyres (Refer to AMM 32-41-00, Page block 601).

6 Do the operational test of the TPIS

WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN

POSITION ON THE LANDING GEAR.

WARNING : MAKE SURE THAT ALL THE CIRCUITS IN MAINTENANCE

ARE ISOLATED BEFORE YOU SUPPLY ELECTRICAL POWER
TO THE AIRCRAFT.

a Job Set-up

- On the Panel 400VU, make sure that the L/G normal control lever
is set to DOWN.

- On the MCDU, get the SYSTEM REPORT/TEST L/G page (Refer to

AMM 31-32-00, Page block 201).

- Put the warning notice(s) in position on the L/G normal control lever to tell
persons not to move it.

b Procedure

ACTION RESULT
1. On the MCDU, push the line key adjacent to the - The TPIS page comes into view.
TPIS indication.
2. On the TPIS page, push the line key adjacent to - The REF PRESSURE page comes into view.
the REF PRESSURE indication.

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 39

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

ACTION RESULT
- Make sure that the values of the reference
pressures in relation to the pin programming are
correct :
M.G. PRESSURE : 210

N.G. PRESSURE : 178

3. Push the line key adjacent to the RETURN
indication until the MCDU menu page comes into
view.

c Close-up

- On the MCDU, push the line key adjacent to the RETURN indication until
the CFDS menu page comes into view.

- Remove the warning notice(s).

(2) Config. 02 thru Config. 05 , Config. 07 , Config. 08 , Config. 10 thru Config. 11

(a) Do a check of the pressure of the tyres (Refer to AMM 32-41-00, Page block 601).

(3) Config. 09

(a) Job Set-up

1 Remove the safety clip and tag and close this circuit breaker :

PANEL DESIGNATION FIN LOCATION

121VU HYDRAULIC/TYRE/PRESS 1GV 31 M

2 Energize the aircraft electrical circuits (Refer to AMM 24-41-00, Page block 201).

(b) Tests

1 Do a functional test of the Tyre Pressure Indicating System (TPIS) (Refer

to AMM 32-49-00, Page block 501).

2 Do the test after the removal/installation of the Smoke Detection Control Unit
(SDCU) (10WQ) (Refer to AMM 26-17-34, Page block 401).

3 Do the test after the removal/installation of the Landing Gear Control and
Interface Unit (LGCIU) (5GA1, 5GA2) (Refer to AMM 32-31-71, Page block 401).

4 Do the test after the removal/installation of the Braking/Steering Control Unit

(BSCU) (10GG) (Refer to AMM 32-42-34, Page block 401).

5 Do a check of the pressure of the tyres (Refer to AMM 32-41-00, Page block 601).

6 Do the operational test of the TPIS

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 40

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN

POSITION ON THE LANDING GEAR.

WARNING : MAKE SURE THAT ALL THE CIRCUITS IN MAINTENANCE

ARE ISOLATED BEFORE YOU SUPPLY ELECTRICAL POWER
TO THE AIRCRAFT.

a Job Set-up

- On the Panel 400VU, make sure that the L/G normal control lever
is set to DOWN.

- On the MCDU, get the SYSTEM REPORT/TEST L/G page (Refer to

AMM 31-32-00, Page block 201).

- Put the warning notice(s) in position on the L/G normal control lever to tell
persons not to move it.

b Procedure

ACTION RESULT
1. On the MCDU, push the line key adjacent to the - The TPIS page comes into view.
TPIS indication.
2. On the TPIS page, push the line key adjacent to - The REF PRESSURE page comes into view.
the REF PRESSURE indication.
- Make sure that the values of the reference
pressures in relation to the pin programming are
correct:
M.G. PRESSURE : 178

N.G. PRESSURE : 178

3. Push the line key adjacent to the RETURN
indication until the MCDU menu page comes into
view.

c Close-up

- On the MCDU, push the line key adjacent to the RETURN indication until
the CFDS menu page comes into view.

- Remove the warning notice(s).

D. CLOSE UP

(1) Config. 01 , Config. 06 , Config. 09

(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 41

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

(b) Make sure that the MLG and NLG tyres are inflated to the pressure shown on the
new placards (Refer to AMM 12-14-32, Page block 301).

(c) De-energize the aircraft electrical circuits (Refer to AMM 24-41-00, Page block 201).

(d) Close the avionics door 811 (Refer to AMM 52-41-00, Page block 201).

(e) Close the passenger/crew door 831 (Refer to AMM 52-10-00, Page block 201).

(f) Remove the access platform(s).

(g) Restore the systems and the aircraft to normal operating condition.

(2) Config. 02 thru Config. 05 , Config. 07 , Config. 08 , Config. 10 , Config. 11

(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.

(b) Make sure that the MLG and NLG tyres are inflated to the pressure shown on the
new placards (Refer to AMM 12-14-32, Page block 301).

(c) Restore the systems and the aircraft to normal operating condition.

E. DOCUMENTATION

Write in the applicable aircraft records that you have done all the work given in the Service Bulletin.

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 42

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

Figure 1, Sheet 1
Config. 01, 02, 04, 05, 09, 10, 11:Installation of the Tyre Pressure Placards on the NLG

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 43

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

Figure 2, Sheet 1
Config. 01 thru 02:Installation of the Tyre Pressure Placards on the MLG

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 44

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

Figure 3, Sheet 1
Config. 03, 06, 07:Installation of the Tyre Pressure Placards on the NLG

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 45

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

Figure 4, Sheet 1
Config. 03:Installation of the Tyre Pressure Placards on the MLG

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 46

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

Figure 5, Sheet 1
Config. 04:Installation of the Tyre Pressure Placards on the MLG

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 47

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

Figure 6, Sheet 1
Config. 05:Installation of the Tyre Pressure Placards on the MLG

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 48

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

Figure 7, Sheet 1
Config. 06 thru 08:Installation of the Tyre Pressure Placards on the MLG

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 49

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

Figure 8, Sheet 1
Config. 09, 11:Installation of the Tyre Pressure Placards on the MLG

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 50

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

Figure 9, Sheet 1
Config. 10:Installation of the Tyre Pressure Placards on the MLG

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 51

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

Figure 10, Sheet 1

Config. 01, 06:Modification to the Wiring in the FWD Electronics Rack 90VU

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 52

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

Figure 11, Sheet 1

Config. 01, 06:Hook-up Chart

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 53

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

Figure 12, Sheet 1

Config. 09:Modification to the Wiring in the FWD Electronics Rack 90VU

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 54

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

Figure 13, Sheet 1

Config. 09:Hook-up Chart

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 55

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN

This Page Intentionally Left Blank

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 56

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN
REPORTING SHEET

TITLE : GENERAL - DESIGN WEIGHTS - INCREASE MTOW TO 77 TONS

MODIFICATION No. : 23264K3065, 23932K3484, 26059K4841

Please complete the appropriate item (A or B):

A - SB WILL BE embodied .................................................................. YES/NO (if NO please comment)

If YES, aircraft concerned (as per SB effectivity by default) and planned dates (month/year) of embodiement:
.............................................................................................................................................................................
.............................................................................................................................................................................

B - SB HAS BEEN embodied on aircraft: ............................................................................................................

.............................................................................................................................................................................
.............................................................................................................................................................................

Operator comments:............................................................................................................................................
.............................................................................................................................................................................
.............................................................................................................................................................................

From Airline: ........................................................................................................................................................

Name/Title: ..........................................................................................................................................................
Signature:..................... Date: .....................................................

If operational documentation is affected (see Paragraph 1.K of this SB): If information is needed prior to next
normal revision or prior to SB embodiment, please indicate required service(s):
Either : Advance data................................................................................... YES/NO
Or : Intermediate/Temporary revision ..................................................... YES/NO

Important Information: This SB will only be incorporated in your maintenance and operational documentation
if this sheet is returned to Airbus and signed by a duly authorised representative. With the next feasible
revision, this will result in
- updating of maintenance documentation to show pre and post SB data.
- updating of maintenance and operational documentation to show post SB data
after embodiment.

If this SB requires previous or simultaneous accomplishment of other SBs, Airbus shall automatically include
them in the manual revisions. Refer to SIL 00-037 for detailed information.
Please return this completed sheet to:

AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX FRANCE

Attn: SEDCC1 Technical Data and Documentation Services

FAX: (+33) 5 61 93 28 06
e-mail: [email protected]
Or via your Resident Customer Support Office.

Alternatively, SB lists via letters or fax are also accepted.

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 1 of 1

Printed in France © AIRBUS 2008 All rights reserved

 SERVICE BULLETIN
REPORTING QUALITY

TITLE : GENERAL - DESIGN WEIGHTS - INCREASE MTOW TO 77 TONS

MODIFICATION No. : 23264K3065, 23932K3484, 26059K4841

Use this form to tell us what is your perception of the quality of this Service Bulletin.The reported data that you
provide us will be used to analyse areas of difficulties and to take corrective action to futher improve the quality
of our Service Bulletins.
We thank you for the time you have taken in completing this form.

(Please rate on a scale of 1 to 4, with 4 being the highest score)

-Quality rating of this SB 4 3 2 1

-Quality rating of the Accomplishment Instructions 4 3 2 1

-Quality rating of the Illustrations 4 3 2 1

-Is this SB easy to understand ? Y/N

If you have had difficulties in the accomplishment of this SB please quote below the area(s) and give a short
description of the issue.

Planning Material Instructions

X Effectivity X Kit Content X Preparation
X Reason X List of Materials X Mod/Inspection
X Manpower Operator Supplied X Test
X References X Re-identification X Close-up
X Publication X Tooling X Illustrations

Comments :

Operator : Date:

Name/Title :

Please return this form to:

AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX FRANCE

Attn: SEMB Service Bulletins Management

FAX: (+33) 5 61 93 42 51
Or via your Resident Customer Support Office.

DATE : Mar 10/93 SERVICE BULLETIN No. : A320-00-1013

REVISION No. : 63 - Apr 01/10 Page : 1 of 1

Printed in France © AIRBUS 2008 All rights reserved