Switches

Catalog Data COOPER POWER

SERIES
Effective March 2024
CA008005EN Supersedes September 2023

D-73P disconnect and

bypass switches

Contents
Description Page
Contents
D-73P disconnect switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
D-73P3 bypass switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
D-73P-CD cutout disconnect switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
D-73P-LT distribution-class line tap disconnect switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
D-73P-VS distribution-class V-style crossarm switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
D-73P-TS distribution-class in-line disconnect switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Catalog Data CA008005EN D-73P disconnect and bypass switches
Effective March 2024

D-73P disconnect switch Application

Eaton has set the new standard of excellence for polymer The D-73P disconnect switch is a single-phase hookstick-operated
distribution-class disconnect switches with the introduction of its switch to sectionalize or isolate overhead lines on electrical
Cooper Power™ series UltraSIL™ polymer-insulated disconnect distribution systems up to 38 kV. The switch can be mounted in
switches. Eaton’s Cooper Power series D-73P distribution-class, a vertical, underhung, pole-mounted, or single/double crossarm
single throw disconnect switch provides a durable, rugged configuration. A variety of terminal connections are available to
lightweight switch for line sectionalizing or isolating equipment customize this switch to fit the user’s needs. Contact your Eaton
on distribution circuits up to 38 kV. These switches are quality representative for more information.
constructed to ensure stable high current capability and full
thermal capacity under the required duties of today’s load and
short circuit conditions.

Features and detailed description

Minimum current interchanges: Uniform

conductivity is assured through utilization
Contacts: High pressure line of hard drawn copper bar in forming one
type, both clip and hinge ends. piece stationary contacts and terminal pads.
Design reduces current interchange points
to a minimum.
Parallel groove clamp: Two-bolt
tinned bronze clamp secured with two
Loadbreak hooks (standard): Galvanized
galvanized steel bolts. Conductor range:
steel hooks to be used with portable
#6 solid to 397.5 MCM ASCR, 500 MCM
loadbreak tool.
Copper or 556 MCM Aluminum.
Blade design: Silver-plated copper in truss-type
construction with cross braces in front and back
of contacts provides secure force on contacts,
as well as superior rigidity, thus minimizing side
deflection and maintaining positive alignment
when closing the switch. The blade and latch
Recloser bypass studs: design provides for positive latch.
With hotline studs at both 90-degree stop pin: Pin included as standard option
ends of the switch, a recloser to provide blade opening stop at 90 degrees. Pin
needing maintenance can able to be removed in field for 180° opening.
be easily bypassed and
disconnected. This can be 150-degree latch: Optional positive stop for
done economically without providing blade latch at 150° opening.
disturbing continuity of
service and without the
use of special tools.

Insulators: Available in lightweight UltraSIL Captive bolts: Two captive stainless

silicone rubber polymer, 2.25 B.C., characteristics. steel carriage bolts. 1-3/4-inch long
Porcelain insulators also available. bolts, accepts compression terminals.

Terminal pad: NEMA® two hole terminal pad.

Capable of accepting wide selection of connectors.
See Table 1 for standard offering. 600 A ratings
have tin-plated pads to accommodate either
bronze or aluminum terminals. 900 A switch Switch base: Base and backstrap is rugged, hot
has silver-plated contacts. dipped galvanized 7 gauge steel that have a dead-
ending hole for conductor at each end. Rigidity of
base prevents distortion/twisting when bolting down.
Standard base offering comes equipped with 1-inch
diameter hole for dead-ending conductors.
Vertical or underhung
mounting: Easily adaptable
to single or double crossarm Backstrap: 15-inch backstrap with two mounting
construction. bolts, washers, lockwashers, and nuts standard.
Optional full length (25.25 inches) REA backstrap
also available with two or four mounting bolts.
Figure 1. D-73P disconnect switch with features

2 www.eaton.com/cooperpowerseries
 D-73P disconnect and bypass switches Catalog Data CA008005EN
Effective March 2024

.63”
(16 mm) 1.75”
(44.4 mm)

2X n.56

1.75”
(44.4 mm)
14.38”
(365 mm)

2X n.56

B
B
Figure 2. D-73P dimensional data .38
.38
1.56 1.56
1.25 7.00
Table 1. D-73P disconnect switch ratings 3.00 1.25 7.00 3.00
Ratings a Catalog number Dimensional data inches (mm) Insulator mechanical ratings

Switch
Insulation kV max. BIL Peak weight Tension, Torsion
material 4.38 design
3.50 kV kA 600 A 900 A A B C D Creep lb Cantilever pounds ft-lb

UltraSIL Polymer 15.5 110 65 D73P16S0 D73P19S0 26 (660) 15 (381) 8.4 (213) 14.38 (365) 20.2 (513) 26.5 1350 5000 350
UltraSIL Polymer 27 125 65 D73P26S0 D73P29S0 3.50 15 (381) 8.4 (213)
4.38 26 (660) 14.38 (365) 20.2 (513) 26.5 1350 5000 350
2X n1.00
UltraSIL
1.25 Polymer 27 150 65 D73P36S0 D73P39S0 29 (737) 1830.00
(457) 10.8 (274) 16.75 (425) 28 (711) 33 1350 5000 350
UltraSIL Polymer 38 150 65 D73P46S0 D73P49S0 29 (737) 18 (457) 10.8 (274) 16.75 (425) 28 (711) 33 1350 5000 350
UltraSIL Polymer 38 200 65 D73P56S0 D73P59S0 34 (859) 23 (580) 15.0 (381) 21.3 (542) 38 (965) 45 1350 5000 350
2X n1.00
1.25
a Meets IEEE Std C37.30.1™-2011 standard. Test reports available upon request. 30.00

www.eaton.com/cooperpowerseries 3
Catalog Data CA008005EN D-73P disconnect and bypass switches
Effective March 2024

6.75" 1.22"
.23" (171 mm) (31 mm)
(6 mm)

Note: Serrated slot base is supplied

4.35" with 3/8 inches by 9 inches long
(111 mm)
carriage bolt with square nuts and
flat washer.
3.00"
(76 mm)
Ø 1.00"
(25 mm)
Standard

A
Note: Smooth slotted base is supplied with
1/2-inch diameter by 9 inches long carriage bolt
B with square nuts and flat washer.

6.75"
(171 mm)
Table 2. Base channels
Dimensions in inches (mm)
BIL A B

Standard 110, 125,150 30.00 (762) 24.09 (612)

.50" 200 37.85 (961) 31.94 (811)

(13 mm)
Slotted 110,125,150 30.00 (762) 24.00 (610)
3.56" Ø 1.00"
(90 mm) (25 mm) 200 31.94 (811) 31.90(810)
Smooth slot base

Figure 3. D-73P bases

15.00" (381 mm)

10.88" (276 mm)

4.13" (105 mm)

3.00" (76 mm)

Standard backstrap

3.75" 3.00" 1.00"

(95 mm) (76 mm) (25 mm)
Note: Serrated slot base
is supplied with 3/8 inches
3.25" by 9 inches long carriage
(83 mm) bolt with square nuts and
1.25"
flat washer.
(32 mm)
2.56" 6.75"
(65 mm) (171 mm)

Table 3. REA backstrap

B Dimensions in inches (mm)
BIL A B
A
110,125,150 25.75 (654) 20.63 (524)

REA serrated slot backstrap 200 33.60 (853) 31.94(811.27)

Figure 4. D-73P backstraps

4 www.eaton.com/cooperpowerseries
D-73P disconnect and bypass switches Catalog Data CA008005EN
Effective March 2024

D-73P3 bypass switch

Eaton provides an economical way for bypassing and disconnecting
pole-mounted distribution-class reclosers and regulators, permitting
maintenance without disturbing continuity of service with its Cooper
Power series UltraSIL polymer-insulated D-73P3 bypass switch.

Normal position Bypass position

Figure 5. D-73P3 3-pull regulator/recloser bypass switch

Application
The D-73P3 bypass switch incorporates all the advanced design All switches have a positive blade lock to prevent opening under
features of the D-73P switch into a compact 3-pull bypass unit. It high momentary current. Easy opening and closing is assured by
consists of two hookstick-operated disconnect switches mounted bolted braces providing consistent forces behind and in front of
on a galvanized channel with a bypass blade connected across the front latch mechanism.
top terminals of each switch. The bypass blade can be arranged for The bypass blade is offset 30 degrees from the plane of the
either right-hand (standard) or left-hand operation (optional). disconnect blades, so that the bypass switch can be operated
One mounting channel supports the entire switch for ease of when the switch is mounted vertically.
installation and uncluttered appearance. The channel can be either
crossarm mounted with a backstrap or bolted directly
to a galvanized pole mounting bracket.

www.eaton.com/cooperpowerseries 5
Catalog Data CA008005EN D-73P disconnect and bypass switches
Effective March 2024

30 °

3.00" 3.00"
(76 (76
mm) mm)
B

7.90"
G (200.6 mm) F
E

C
I
H

Top view Side view

Figure 6. D-73P3 top and side view with dimensional data

Table 4. D-73P3 bypass switch ratings

Ratings Catalog number Dimensional data inches (mm)
Insulation kV max. BIL Peak Insulator Weight
material design kV kA 600 A 900 A creep (lb) A B C D E F G H I

20.2 26 30 25.95 8.4 9.1 13.45 15 17.75 12.75

UltraSIL Polymer 15.5 110 65 D73316S0 D73319S0 (513) 62 (660) (762) (659) (213) (231) (342) (381) (451) (324)
20.2 26 30 25.95 8.4 9.1 13.45 15 17.75 12.75
UltraSIL Polymer 27 125 65 D73326S0 D73329S0 (513) 62 (660) (762) (659) (213) (231) (342) (381) (451) (324)
28 29 30 28 10.8 13 15.75 18 20.75 15.75
UltraSIL Polymer 27 150 65 D73336S0 D73339S0 (711) 75 (660) (762) (711) (274) (330) (400) (457) (527) (400)
28 29 30 28 10.8 13 15.75 18 20.75 15.75
UltraSIL Polymer 38 150 65 D73346S0 D73349S0 (711) 75 (660) (762) (711) (274) (330) (400) (457) (427) (400)

9.375"
(238 mm)

2.125"
(54 mm)
H

1.41 REF ø.56 X 4.06 SLOT

(36 mm) 2 PLACES

3.00 REF
(76 mm)
1.500"
(38 mm)

15.00"
(381 mm)

Figure 7. Backstrap for crossarm mount (standard offering)

6 www.eaton.com/cooperpowerseries
D-73P disconnect and bypass switches Catalog Data CA008005EN
Effective March 2024

7.00"
(177.8 mm)
5.49" 1.63"
(139 mm) (41 mm)
4.00"
(101.6 mm)
A REF

13.25"
(336.5
mm)
11.25"
(285.7
mm)

Figure 8. Pole-mount bracket and extended pole-mount bracket

A REF

Figure 9. Cluster-mount bracket

Table 5. Pole-mount and cluster-mount brackets

Part Dimension A
Number (inches) Application

262400-S6 19.57 Pole mount

262400-E-S6 25.45 Pole mount
262400-2-S6 19.57 Cluster mount

www.eaton.com/cooperpowerseries 7
Catalog Data CA008005EN D-73P disconnect and bypass switches
Effective March 2024

Ordering information required

To order a D-73P disconnect or D-73P3 bypass switch, use the
catalog number noted in Table 6. Modify digits 4–9 to adapt the
unit to the specific application.

Table 6. Ordering information

1 2 3 4 5 6 7 8 9

D 7 3 P 1 6 S 0 P
BASE CATALOG
NUMBER

CODE VOLTAGE BIL CODE BASE

CODE SWITCH TYPE 1 15 kV, 110 BIL 0 a Serrated Slot
P Distribution-Class 2 27 kV, 125 BIL 2 Smooth Slot
Disconnect Switch a Digit 8 always “0” for D-73P3.
(D-73P) 3 27 kV, 150 BIL
3 Distribution-Class 4 38 kV, 150 BIL CODE OPTIONS
Recloser/Regulator
Bypass Switch 5a 38 kV, 200 BIL A 150-Degree Latch a
(D-73P3) a Digit 5 can only be “5” for D-73P.
B Bypass Studs (D-73P only) a
C Captive Bolts a
CODE CURRENT
D REA Backstrap (2-3/8" x 9" Bolts)
6 600 A (D-73P only) see Figure 4
9 900 A E REA Backstrap (4-3/8" x 9" Bolts)
(D-73P only) see Figure 4
L Left-Hand Operation
CODE INSULATOR (D-73P3 only)
MATERIAL
M Pole-mount Bracket b
S Silicone Rubber (D-73P3 only) see Figure 8
P Porcelain N Without 90° Stop Pin a
P Parallel Groove Clamp ac
R No Backstrap
S Stainless Steel Loadbreak Hook a
U Cluster Mounting Bracket
(D-73P3 only) see Figure 9
X Extended Pole-mount Bracket
(D-73P3 only) see Figure 8
a See Figure 1 on page 2 for additional details on
available options.
b 2-bolt backstrap standard for bypass switch.
c Conductor range: #6 solid to 397.5 MCM ASCR,
500 MCM Copper or 556 MCM Aluminum.
Note: Leave digit 9 blank if no option is required.

Example: 600 A, 15 kV, D-73P disconnect switch in silicone rubber with standard base and parallel
groove clamp = D73P16S0P

8 www.eaton.com/cooperpowerseries
D-73P disconnect and bypass switches Catalog Data CA008005EN
Effective March 2024

D-73P-CD cutout disconnect switch

Eaton’s Cooper Power series D-73P-CD single insulator cutout
disconnect switch is single-phase hookstick-operated switch
designed for operation at 600 A and 900 A on overhead distribution
circuits rated up to 38 kV, 150 kV BIL. The cutout disconnect style
switch is designed for riser pole applications where the switch is
easily installed with included crossarm bracket much like a standard
cutout. The lightweight switch package reduces the need of double
crossarm mounting when using cutout bracket.
The cutout disconnect style switch combines Eaton’s Cooper Power
series Type L cutout and the live parts of D-73P disconnect switch
to provide a rugged and reliable low-cost switching device. The field
proven blade design offers silver-plated truss-type construction with
cross braces in front and in back of contacts to minimize deflection,
maintain positive alignment, and ensure efficient current transfer
between blade and contacts.
The D-73P-CD switch comes standard with a loadbreak hook to be
used with the tool for opening the switch under load. Loadbreak
hooks also act as a blade alignment guide to help in safe, reliable
closing operation. The D-73P-CD switch is easy to install using
crossarm mounting bracket in the same manner as a cutout. Use a
D-73P‑CD switch where a lightweight switch package is required.

Figure 11. D-73P-CD disconnect switch with features

Bracket will accept

4.1 to 5.1 inches

Table 7. Ratings
Ratings Dimension
Max.
Catalog voltage Amperes Length "X"
number (kV) (A) BIL (kV) inches (mm) Creep

D73CD16S0 15.5 600 110 26 (660) 14.2 (362)

X
D73CD19S0 15.5 900 110 26 (660) 14.2 (362)
2.6 inches D73CD26S0 27 600 125 26 (660) 14.2 (362)
standard bracket,
5.9 inches D73CD29S0 27 900 125 26 (660) 14.2 (362)
extended bracket D73CD36S0 27 600 150 29.5 (749) 22.3 (566)
D73CD39S0 27 900 150 29.5 (749) 22.3 (566)
D73CD46S0 38 600 150 29.5 (749) 22.3 (566)
D73CD49S0 38 900 150 29.5 (749) 22.3 (566)

a X = total switch length

Figure 10. D-73P-CD disconnect switch with features

www.eaton.com/cooperpowerseries 9
Catalog Data CA008005EN D-73P disconnect and bypass switches
Effective March 2024

D-73P-LT distribution-class line tap

disconnect switch
Eaton’s Cooper Power series D-73P-LT single insulator line tap
disconnect switches are a single-phase hookstick-operated switch
designed for operation at 600 A and 900 A on distribution circuits to
38 kV, 150 kV BIL.
Line tap style disconnect switches provide a rugged and reliable
disconnect option for an assortment of cable-riser and crossover
applications. The silver-plated copper truss-type blade assembly
provides superior strength and smooth reliable latching mechanism.
The D-73P-LT switch comes standard with loadbreak hook to be
used with tool for opening switch under load. Loadbreak hooks
also act as a blade alignment guide to help in safe, reliable
closing operation.
Standard polymer insulators provide reduced weight and added
durability for easier installation and enhanced ruggedness in
the field. Many available options, accessories, and hanging Figure 12. D-73P-LT disconnect switch with features
configurations make the D-73P-LT switch a flexible solution to
any overhead line tap application.
Angled hanger set 3/4-inch diameter

3/4"

5.25"
.50"
Angled hanger set 1-inch diameter

1"

5.25"
.50"

Straight hanger set 1-inch diameter

1"

Figure 13. D-73P-LT disconnect switch with features 6.50"

.50"
Table 8. Catalog numbers and ratings
Ratings Dimensional data inches (mm)
Amperes
Catalog number Max. voltage (kV) (A) BIL (kV) A B C D E F G

D73LT16S0 15.5 600 110 10.5 (267) 8.375 (213) 28.0 (711) 27.25 (692) — 5.25 (133) 30.25 (768)
D73LT19S0 15.5 900 110 10.5 (267) 8.375 (213) 28.0 (711) 27.25 (692) — 5.25 (133) 30.25 (768)
D73LT26S0 27 600 125 10.5 (267) 8.375 (213) 28.0 (711) 27.25 (692) — 5.25 (133) 30.25 (768)
D73LT29S0 27 900 125 10.5 (267) 8.375 (213) 28.0 (711) 27.25 (692) — 5.25 (133) 30.25 (768)
D73LT36S0 27 600 150 13.5 (343) 10.75 (273) 31.0 (787) 30.625 (778) 6.50 (165) 5.25 (133) 33.625 (854)
D73LT39S0 27 900 150 13.5 (343) 10.75 (273) 31.0 (787) 30.625 (778) 6.50 (165) 5.25 (133) 33.625 (854)
D73LT46S0 38 600 150 13.5 (343) 10.75 (273) 31.0 (787) 30.625 (778) 6.50 (165) 5.25 (133) 33.625 (854)
D73LT49S0 38 900 150 13.5 (343) 10.75 (273) 31.0 (787) 30.625 (778) 6.50 (165) 5.25 (133) 33.625 (854)

10 www.eaton.com/cooperpowerseries
D-73P disconnect and bypass switches Catalog Data CA008005EN
Effective March 2024

D-73P-VS distribution-class V-style

crossarm switch
Eaton designs its Cooper Power series D-73P-VS distribution-class
V-style crossarm switches for operation at 600 A and 900 A on
distribution circuits rated up to 38 kV, 150 BIL.
The silver-plated copper truss-type blade assembly provides superior
strength and smooth reliable latching mechanism. The field proven
blade design offers silver-plated truss-type construction with cross
braces in front and in back of contacts to minimize deflection,
maintain positive alignment, and ensure efficient current transfer
between blade and contacts. D-73P-VS switches come standard
with a loadbreak hook to be used with tool for opening switch under
load. Loadbreak hooks also act as a blade alignment guide to help in
safe, reliable closing operation. Standard polymer insulators provide
reduced weight and added durability for easier installation and
enhanced ruggedness in the field.

Figure 14. D-73P-VS disconnect switch with HOM-style base

www.eaton.com/cooperpowerseries 11
Catalog Data CA008005EN D-73P disconnect and bypass switches
Effective March 2024

1"

0.44" dia.
4.75"

B
1.2" x 0.44" dia.

Rear Base View

Figure 15. D-73P-VS disconnect switch with HOM-style base

Table 9. Catalog numbers and ratings

Ratings Dimensions inches (mm)
Amperes
Catalog number Max. voltage (kV) (A) BIL (kV) Creep A B C

D73VS16S4 15.5 600 110 20.2 (513) 10.50 (267) 8.375 (213) 24.25 (616)
D73VS19S4 15.5 900 110 20.2 (513) 10.50 (267) 8.375 (213) 24.25 (616)
D73VS26S4 27 600 125 20.2 (513) 10.50 (267) 8.375 (213) 24.25 (616)
D73VS29S4 27 900 125 20.2 (513) 10.50 (267) 8.375 (213) 24.25 (616)
D73VS36S4 27 600 150 28.0 (711) 13.50 (343) 10.75 (273) 27.00 (686)
D73VS39S4 27 900 150 28.0 (711) 13.50 (343) 10.75 (273) 27.00 (686)
D73VS46S4 38 600 150 28.0 (711) 13.50 (343) 10.75 (273) 27.00 (686)
D73VS49S4 38 900 150 28.0 (711) 13.50 (343) 10.75 (273) 27.00 (686)

12 www.eaton.com/cooperpowerseries
D-73P disconnect and bypass switches Catalog Data CA008005EN
Effective March 2024

Ordering information required

To order a D-73 disconnect switch, use the catalog number noted in
Table 10. Modify configuration digits 4–10 as required to adapt the
unit to the specific application.

10.3
(260 mm)
8.9
(227 mm)
13.3
(339 mm)

12.0 2.6
(305 mm) (67 mm)

Figure 16. NEMA D bracket with standard L bracket only

Table 10. Ordering information

1 2 3 4 5 6 7 8 9 10

D 7 3 C D 1 6 S 0 X
BASE CATALOG
NUMBER
CODE VOLTAGE, BIL CODE INSULATOR
MATERIAL
1 15.5 kV, 110 BIL
CODE DESCRIPTION S Silicone Rubber
2 27 kV, 125 BIL
Cutout Disconnect
CD 3 27 kV, 150 BIL
Switch
LT Line Tap Switch 4 38 kV, 150 BIL
Crossarm Vertical
VS CODE BASE
Switch
CODE AMP
0 CD, LT
6 600 A
4 HOM Base for VS
9 900 A

CODE OPTION
A 150-Degree Latch b
C Captive Bolts (1.75" Long, SST) b
D NEMA D Bracket (for CD)
N No Mounting Bracket (for CD)
P Parallel Groove Connector b
X Extended Mounting Bracket (For CD)
H3 a 1" Straight Hanger (LT Type Only)
H4 1" Angled Hanger (LT Type Only)
Example: D73CD16S0X - 600 A, 15 kV, D73-CD switch with silicone rubber
insulators and extended mounting bracket. H5 3/4" Angled Hanger (LT Type Only)
a 1-inch straight hanger not available on switches with
option code 1 or 2 in digit 6.
b See Figure 1 for additional details on available options.

Note: Leave digit 10 blank if no option is required.

www.eaton.com/cooperpowerseries 13
Catalog Data CA008005EN D-73P disconnect and bypass switches
Effective March 2024

D-73P-TS distribution-class in-line

disconnect switch
Eaton's Cooper Power series D-73P-TS single insulator in-line
tension switches are single-phase hookstick-operated manual
switches designed for operation of overhead lines on distribution
circuits of 15 kV through 38 kV, 150 kV BIL or 200 kV BIL. The
D-73P-TS switches are rated at 600 A or 900 A continuous current
and may be applied directly into the line wherever line sectionalizing
is desired.
The in-line tension style switches provides a rugged and reliable
disconnect option for line sectionalizing. The silver-plated D73 type
copper truss-type blade assembly provides superior strength and
smooth reliable latching mechanism. The switches come standard
with loadbreak hook to be used with the appropriate tool for opening
the switches under load. Loadbreak hooks also act as a blade Figure 18. In-line tension switch in closed position
alignment guide to help in safe, reliable closing operation.
UltraSIL silicone rubber polymer insulator with crimped end fittings
provides reduced weight and added durability for easier installation
and enhanced ruggedness in the field. The extra long creep makes
the switch ideal for high pollution and coastal environments.
The switch is equipped with terminals providing NEMA® spacing in
several different directions. This allows for increased flexibility during
installation depending on the application requirements.

Table 11. Catalog numbers and ratings

Insulator Rated ultimate
Power Momentary Momentary creep distance tension strength
Base catalog Continuous frequency dry current current
number current (A) BIL (kV) 60 sec (kV) (rms kA) (Peak kA) (Inches) (mm) (lb) (N)

D73TS36S0 600 150 70 25 65 23.2 589 15,000 66,723

D73TS39S0 900
D73TS56S0 600 200 95 25 65 38.9 988 15,000 66,723
D73TS59S0 900

B See Detail A Below

8x Ø.57
(14.48)
For Electrical 2x Ø.69
3.75 Connection (17.53)
(95.25) 2.75 For Electrical
(69.85) Installation

6.60
(167.71)

Latch 150° Load Buster Hook

1.75
(44.45)

30.0°
1.75
(44.45)
Detail A

Figure 17. D-73P-TS in-line tension disconnect switch with features

14 www.eaton.com/cooperpowerseries
D-73P disconnect and bypass switches Catalog Data CA008005EN
Effective March 2024

Table 12. Dimensional information

Dimensional data in inches (mm)
Base catalog Continuous
number current (A) BIL (kV) A B C

D73TS36S0 600 150 24.1 (612) 22.1 (560) 13.3 (338)

D73TS39S0 900 150 24.1 (612) 22.1 (560) 13.3 (338)
D73TS56S0 600 200 29.1 (739) 27.1 (687) 18.3 (465)
D73TS59S0 900 200 29.1 (739) 27.1 (687) 18.3 (465)

Ordering information
To order a D-73P-TS in-line tension disconnect switch, use the base catalog
number noted in Table 12. Add options as required from Table 13.

Table 13. Options

Code Option

A 150-degree latch (see Figure 16)

P Parallel groove connectors a
Y Four SS terminal bolts with hardware
U 45-degree two-hole NEMA contact pad

a Conductor range: #6 solid to 397.5 MCM ASCR, 500 MCM copper or 556 MCM aluminum.

Coastal—corrosion-resistant switches
Eaton offers a selection of our most popular switch styles improved
for corrosion resistance. Switch styles with coastal corrosion
resistance options:
• D-73P single-phase disconnect
• D-73CD single-phase cutout disconnect

Coastal versions of the D-73 single-phase switches incorporate a

rugged stainless steel base, hardware, and load-buster hooks that
prevent pitting and corrosion in even the harshest environments.

Table 14. Ordering information

D 7 3 P 1 6 S 0 R -SS
BASE CATALOG
NUMBER
CODE VOLTAGE, BIL CODE CURRENT CODE CURRENT
1 15.5 kV, 110 BIL 0 Serrated Slot SS Stainless Steel -
CODE DESCRIPTION Coastal
2 27 kV, 125 BIL 2 Smooth Slot
Distribution-Class
P Disconnect Switch 3 27 kV, 150 BIL
(D-73P) CODE INSULATOR CODE OPTIONS
4 38 kV, 150 BIL
Cutout Disconnect MATERIAL
CD 5 38 kV, 200 BIL C Captive Bolts
(D-73CD) S Silicone Rubber
D REA Backstrap
(2-1/2" x 10" Bolts)
CODE AMP (D-73P only)
6 600 A N Without 90° Stop Pin
9 900 A R No Backstrap
U Cluster Mounting
bracket (D-73P only)
see Figure 9

www.eaton.com/cooperpowerseries 15
Catalog Data CA008005EN D-73P disconnect and bypass switches
Effective March 2024

Eaton
1000 Eaton Boulevard
Cleveland, OH 44122
United States
Eaton.com

Eaton’s Power Systems Division

2300 Badger Drive
Waukesha, WI 53188
United States
Eaton.com/cooperpowerseries

© 2024 Eaton
All Rights Reserved Eaton is a registered trademark.
Printed in USA For Eaton's Cooper Power series product
Publication No. CA008005EN / ZD28568 All other trademarks are property information, call 1-877-277-4636
Marh 2024 of their respective owners. or visit: www.eaton.com/cooperpowerseries.