0% found this document useful (0 votes)
39 views9 pages

NA Final QB-2024-25

Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
39 views9 pages

NA Final QB-2024-25

Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 9

Department of Electronics and Communication Engineering

Network Analysis
Question Bank (2024-25)

MODULE -1
RBT
Q. No Question
Level
1. Derive an expression for star to delta transformation and delta to star L2
transformation.
2. Identify the equivalent resistance between A & B for the figure shown below.

L3

3. Solve for equivalent resistance across AB terminals in the below figure.

L3
4. In the circuit shown in below determine the currents i1; i2 and i3 using mesh
analysis.

L3

5. Make use of mesh analysis to find the current through branch a-b.

L3

6. For the circuit shown in the figure determine the current through 30Ω resistance
using Mesh analysis.

L3

7. Write the mesh equation for the circuit shown in below figure and determine
mesh currents using mesh analysis.

L3

8. Make use of source transformation to find I1 that gives V2 =6.5V in the circuit
shown in the circuit show in below figure.

L3
9. Calculate the current through 2 ohms resistor in the network shown below by
source transformation method.

L3

10. For the network shown in the figure determine the voltage V using source shift
and/or source transformation techniques only.

L3

11. In the network shown in Figure determine the node voltages using nodal
analysis.

L3

12. Make use of nodal analysis to find the current through each resistor of the circuit
shown in the figure

L3

13. For the circuit shown in below find the branch current I1, I2, I3 and node voltage
V1, V2

L3
MODULE -2
RBT
Q. No Question
Level
1. State and Prove reciprocity theorem with relevant circuit diagram L2
2. State and Prove Norton’s theorem L2
3. State and prove Thevenin’s theorem with relevant circuit diagram L2
4. Verify the reciprocity theorem for the voltage V and current I in the network
shown in below figure

L2

5. Use millman’s theorem to find the current through the 10Ω resistance in the
circuit of below figure.

L3

6. For the circuit shown below, determine the current I0 using Superposition
theorem.

L3

7. Determine the current through RL=7.5Ω using Superposition theorem in the


network shown below.

L3

8. Determine ix and hence verify Reciprocity theorem for the network shown
below.

L3
9. Make use of Norton’s theorem, to find the current through the load impedance
ZL.

L3

10. Determine the current through branch ‘b-e' using Norton’s theorem.

L3

11. Obtain the current Ix by Thevenin’s theorem.

L3

12. Obtain the Thevenin’s equivalent of network shown in the figure between
terminal x and y. Also find V0

L3

13. For the circuit shown in figure determine value of R that will deliver maximum
power to the load. Also find the power.

L3
MODULE -3
RBT
Q. No Question
Level
1. Define attenuation. Express attenuation in terms of nepers and decibels L2
2. Design lattice attenuator L3
3. Design t-type and 𝜋-type attenuator L3
4. Design t-type and ladder type attenuator. L3
5. Derive an expression for insertion loss. L3
6. Design an L-type attenuator to operate into a resistance of 500Ω and to provide L3
an attenuation of 15dB
7. Design 𝜋-type attenuator with characteristic impedance of 500Ω and
attenuation 20dB L3

8. Define filter. Explain the filter fundamentals. L2


9. Design constant K-low pass filter. L3
10. Design constant K-high pass filter. L3
11. Design constant K-band pass filter and band elimination filter L3

MODULE -4
RBT
Q. No Question
Level
1. Mention the characteristics of resonance and derive the equation for resonant
L2
frequency of series resonant circuit.
2. Show that the resonant frequency is geometric mean of two half power
L2
frequencies.
3. Define bandwidth and selectivity. Drive an expression for bandwidth. L2
4. Derive the expressions for a resonant frequency for a parallel circuit containing L2
resistance in both branches.
5. A series RLC circuit consists of R=100Ω, L=0.02H and C=0.02µF calculate
L3
frequency of resonance, Q-factor and half power frequencies.
6. A coil is connected in series with variable capacitor across v(t)=10cos1000t, the
capacitor is varied and the current is maximum when C=10μf. When C=12.5μf the L3
current is 0.707 times the maximum value. Find L, R and Q of the coil.
7. A parallel circuit has a fixed capacitor and variable inductor having constant
quality by factor of 4. Find value of inductance and capacitance for circuit
L3
impedance of 1000Ω at resonating frequency 2.4mhz. What is the bandwidth of
the circuit?
8. Find out the laplace transform of i) f(t)=e-at for t>=0, ii) f(t)=sin⍵t for t>=0 L2
9. Define and explain laplace transform of standard functions
i. Step function
L2
ii. Ramp function
iii. Impulse function
10. Obtain the laplace transform of sawtooth waveform show in below figure

L3

11. Obtain the laplace transform of square wave train show in below figure

L3

MODULE -5
RBT
Q. No Question
Level
1. Define Z and ABCD parameters and derive expression for transmission L2
parameters and draw its equivalent circuit.
2. Obtain H parameters in terms of Z and Y Parameters L2
3. Obtain Y parameters in terms of ABCD and H Parameters. L2
4. Determine y-parameters of the two-port network shown below

L3

5. For the network shown obtain the O.C impedance parameters L3


6. Determine the transmission parameters for the network shown below

L3

7. Determine the transmission parameters for the network shown below

L3

8. The Z parameters of a two-port network are Z11=20Ω, Z22=30Ω, Z12=Z21=10Ω


L3
Find ABCD and Y parameters.

9. Find Z-parameters of the two-port network shown below.

L3

10. Find Y-parameters of the two-port network shown below

L3

11. Find H-parameters of the two-port network shown below.

L3
12. Two networks have been shown in below figure obtain the transmission
parameters of the resulting circuit when both the circuit are cascade.

L3

You might also like