INTEGRA-7 Editor Ver.

2 Owner’s Manual

Copyright © 2014 ROLAND CORPORATION

All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION. 01
 Contents
About INTEGRA-7 Editor Ver.2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

How the Screens Are Organized . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

How the Editor Is Organized . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
[STUDIO SET] tab. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
[TONE] tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
[MOTIONAL SURROUND] tab. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
[EFFECTS] tab. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
[SYSTEM] tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
[EXPANSION] tab. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
[UTILITY] button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Loading a Studio Set (READ). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Loading a Studio Set. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Saving the Studio Set and Tones. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Saving a Studio Set. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Saving a Tone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

About INTEGRA-7 Editor Ver.2

INTEGRA-7 Editor Ver.2 can be plugged into a DAW that supports VST instruments (VSTi) or Audio Units (AU), allowing you to edit the INTEGRA-7’s studio sets, tones,
and other parameters. Parameters that you edit in the editor are sent in real time to the INTEGRA-7 to apply your edits.
Since the content that you edit can be saved in the INTEGRA-7 itself, you can use the saved settings even when you create other projects on your DAW.

2
 How the Screens Are Organized
How the Editor Is Organized
You can switch the display between the studio sets, parts, or parameters that you’re editing.

The selection area consists of a pull-

Studio Set selection area down button for switching studio sets TYPE/ BANK/ CATEGORY/ TONE selection area Menu selection tabs
and tones, and an area that lets you view
Here you can select the studio set and edit the name of the corresponding Here you can switch types, banks, and categories, Here you can switch the items
that you want to edit. item. Pull-down button and choose a tone for the part you’ve selected. that are displayed for editing,
All settings change when you switch such as studio sets, tones, and
studio sets. effects.

PART selection area [READ] button

Select the part that you want to edit. This loads settings from the
INTEGRA-7 into the editor.
P. 1 1

Parameter list
The editable parameters and menu
[UTILITY] button
items are listed here.
This lets you save or initialize a
The contents that you see depend
studio set or tone.
on what you’ve selected in the menu
select tabs and other buttons, and P. 1 2
the type of tone that’s selected.

[PREVIEW] button
Click this to audition the edit-
Edit area
ed tone.
This area shows the values of the
parameters that you’ve selected in
the parameter list.

3
 How the Screens Are Organized

[STUDIO SET] tab

In the [STUDIO SET] tab you can edit overall settings for the entire studio set and make detailed settings for each part.

PART VIEW
For each part, you can select the tone and
adjust its level and pan to create the balance
for the entire studio set.
For an EX part, you can adjust the level of the
external input (INPUT jack).

STUDIO SET COMMON

Here you can adjust overall settings that apply
to the entire studio set, such as tempo, tone
control, and phase lock.

PART
Here you can make detailed adjustments to
parameters such as level, equalizer, pitch, and
scale for each part.

4
 How the Screens Are Organized

[TONE] tab
In the [TONE] tab you can select the instrument and partials that are the basis of the tone, and edit the parameters to modify the sound.

COMMON
These settings apply to the entire tone.
The parameters that are shown in the edit
area depend on the type of tone that’s select-
ed.

The parameters that are shown depend on

the type of tone that’s selected.

* This screen shows an example where a

SuperNATURAL acoustic tone is selected.

5
 How the Screens Are Organized

[MOTIONAL SURROUND] tab

In the [MOTIONAL SURROUND] tab you can control the stereo position and depth of each part.

COMMON
These settings edit the reverb type, room size,
and ambience.

CONTROL
Here you can specify the MIDI channel that
will control the parameters of the Ext part.

PART
Here you can adjust the stereo position and
depth of each part.
To make adjustments, drag the node that’s
labeled with the part number, or move the
sliders located above and at the right of the
graph.

6
 How the Screens Are Organized

[EFFECTS] tab
In the [EFFECTS] tab you can edit the settings of the effects used by the tone, part, or studio set.

TONE
Here you can specify the type and character
of effect (MFX) that’s applied to the tone.
You can also make MFX CONTROL (multi-effect
control) settings for using MIDI to control MFX
parameters.

PART EQ
For each part you can turn the equalizer on/
off, and adjust the cutoff frequency and gain.

STUDIO SET
Here you can edit the reverb, chorus, and
master EQ parameters.
For the rhythm part, you can apply a com-
pressor and equalizer specifically for drums,
and specify the output jacks from which the
sound is output.

7
 How the Screens Are Organized

[SYSTEM] tab
In the [SYSTEM] tab you can make settings for tuning and specify how MIDI messages are received.

SOUND
These settings specify the master level, master
tune, and key shift.

SYNC/TEMPO
These settings let you synchronize the INTEG-
RA-7 with another device.

MIDI
These settings specify how MIDI messages are
received.

MOTIONAL SURROUND
These settings specify how motional surround
is output.

CONTROL
These settings specify the MIDI messages
used to control parameters common to the
entire INTEGRA-7, such as volume and tone.

8
 How the Screens Are Organized

[EXPANSION] tab
In the [EXPANSION] tab you can load sound data into the INTEGRA-7’s virtual slots for use.

VIRTUAL SLOT
Select the sound data that is loaded into the
four virtual slots.
When you’ve made your selection, click the
[LOAD] button to load the data.

9
 How the Screens Are Organized

[UTILITY] button
By clicking the [UTILITY] button you can save the studio set and tone settings that you’ve edited, or initialize a studio set, tone, or partial.

STUDIO SET WRITE

This saves the edited studio set into the save-destination
that you specify. The saved studio set will be available for
selection in the STUDIO SET selection area.

TONE WRITE
This saves the edited tone into the save-destination that
you specify. The saved tone will be available for selection
in the TYPE/BANK/CATEGORY/TONE selection area.

STUDIO SET INIT/PART INIT/SOUND CTRL INIT/

TONE INIT/PARTIAL INIT
This initializes the settings of the selected studio set, part,
sound control, tone, or partial.

DEVICE
This lets you make settings for INTEGRA-7 Editor Ver.2.

MANUAL/VERSION
MANUAL: Displays this manual.
VERSION: Displays the version of the editor.

10
 Loading a Studio Set (READ)
A studio set saved in the INTEGRA-7 itself can be loaded into INTEGRA-7 Editor Ver.2 and edited.

Loading a Studio Set

1. On the INTEGRA-7, select the studio set that you want to edit in the
editor.

2. Start INTEGRA-7 Editor Ver.2, and click the [READ] button.

The [READ] dialog box appears.

3. Click the [OK] button to load the studio set.

* The time required to load the studio set de-
pends on your computer system and on the
studio set.

4. When you’re finished editing, save your

changes as described in “Saving the Studio Set and Tones” (p. 12).

11
 Saving the Studio Set and Tones
The studio set and tones you’ve edited are temporary. If you turn off the power of the INTEGRA-7 itself, or select another studio set or tone, the edited content is lost.
When you’re finished editing or want to pause for a while, be sure to save the edited content.

Saving a Studio Set Saving a Tone

1. In the “STUDIO SET selection area, ” click 1. In the “TONE selection area, ” click the
the studio set name. studio set name.
The [STUDIO SET RENAME] dialog box ap- The [TONE RENAME] dialog box appears.
pears.

2. Edit the studio set name, and click the 2. Edit the tone name, and click the [Re-
[Rename] button. name] button.
* If you’re using SONAR, turn on the [Key- * If you’re using SONAR, turn on the [Key-
stroke] button located in the upper right stroke] button located in the upper right
of the editor, and enter the name. of the editor, and enter the name.
3. Click the [UTILITY] button. 3. Click the [UTILITY] button.
The parameter list display changes. The parameter list display changes.
4. Click [STUDIO SET WRITE] to see the list of studio sets. 4. Click [TONE WRITE] to see the list of studio sets.
5. Click the [WRITE] button of the number in which you want to save the edited 5. Click the [WRITE] button of the number in which you want to save the edited
studio set. studio set.
The [STUDIO SET WRITE] dialog box appears. The [TONE WRITE] dialog box appears.
6. Click the [OK] button. 6. Click the [OK] button.
The studio set is saved in the number that is The tone is saved in the number that is
selected on the INTEGRA-7 itself. selected on the INTEGRA-7 itself.

N OT E N OTE
Do not turn off the power of the INTEGRA-7 itself while data is being Do not turn off the power of the INTEGRA-7 itself while data is being
saved. saved.

12