ntroduction to Mechatronics

Dr. Shimi S.L

Associate Professor
Electrical Engineering Department
Punjab Engineering College
Chandigarh
Course Name : Introduction to Mechatronics
Course Code : ES 2304
Credits : 04
L T P : 3-0-2
Course Objectives:
The objective of the course content is to:

1. Impart knowledge and information about mechatronics system.

2. Understand the concepts of signal conditioning and data acquisition for
intelligent systems.
3. Develop the basics for mechatronic product design
Course Outcomes:
By the end of this course, the student will be able:

CO1: To understand the basic concepts, applications and components of

mechatronic system.
CO2: To analyze sensing, signal conditioning and data acquisition circuits.
CO3: To design product and systems theoretically as well as practically with
Intelligence.
CO4: To apply the knowledge of mechatronic system for industrial applications.
Topic Hr
Chapter 1 - Introduction to Mechatronics : Introduction, Elements 6
of Mechatronics system, Classification of Mechatronics system,
Mechatronic system intelligence, Components involved in
intelligent system design and development, measurements and
control system as a part of mechatronics system, Application of
Mechatronic systems
Chapter 2 - Sensors and transducers : Introduction, Performance 8
characteristics of transducers, Transducer for displacement
(Potentiometer, strain-gauge, Optical encoder, LVDT, Hall effect
sensor); velocity (Tachogenerator), force (load cell), pressure
(Piezoelectric sensors, Tactile sensor), liquid level ( Floats,
Differential pressure), Temperature (Bimetallic strips, RTDs,
Thermistors, Thermocouples) and light sensor (Photovoltaic-
transducer, LDR, Photodiode, Photo Transistor).
Chapter 3 - Signal conditioning: Operational amplifier 7
(Inverting, Non-inverting, Summing, Integrating,
Differential amplifiers, comparator), protection,
filtering, digital signals (R-2R ladder DAC and
Successive Approximation ADC), Concepts of
multiplexers
Chapter 4 - Controllers: Basics of number system, binary, 7
octal and hexadecimal systems with their conversion from
one system to other. Boolean algebra, logic gates, ICs,
flip-flops & counters.
Microprocessor, Microcontroller, PLC & their
Architectures, Working Principle, Software Programs
(Assembly/High Level), Interfacing Aspects
Flipped Learning (NPTEL MOOCs) - https://nptel.ac.in/courses/112107298)
Basics of number, binary, octal and hexadecimal systems with their
conversion from one system to other. Boolean algebra, logic gates, ICs,
flip-flops. (Unit 5 Lecture 21&22) PLC Controller (Unit 7 Lecture 33)
Chapter 5 - Actuators and mechanisms: 8
Pneumatic and hydraulic actuation systems: Directional
control valves, Pressure control valves, cylinders
Mechanical actuation systems: Kinematic chain, cam,
gear, clutches, ratchet and pawl, belt and chain drive,
bearings
Electrical actuation systems: Relays, Solid-state Switches
(Diode, Thyristor, Triac, BJT, FET), DC and AC motors,
brushless dc motor, stepper motors, servo motors
Flipped Learning (NPTEL MOOCs) - https://nptel.ac.in/courses/112107298)
Mechanical actuation systems: Kinematic chain, cam, gear, ratchet and pawl,
belt and chain drive, bearings (Unit 3 Lecture 11)
Pneumatic and hydraulic actuation systems: Directional control valves, Pressure
control valves, cylinders (Unit 3 Lecture 12)
Chapter 6 - Robotics: Types of motions, Function, 6
Governing Laws, Classification, Features and Components
of Robots, System Automation
 Reference Books
Year of
Sr. No. Name of Book/ Authors/ Publisher Publication/
Reprint

Mechatronics by W Bolton , 6th edition,

1 2019
Pearson Education
Mechatronics by Tilak Thakur 2st edition,
2 2023
Oxford University Press
Mechatronics by Dan Necsulescu, Pearson
3 2001
Education
4 Mechatronics by H M T Limited, TMH 2017

Mechatronics Principles, Concepts &

5 2017
Applications by Nitaigour P Mahalik, TMH
S.No. Link of Journals, Magazines, websites and Research
Papers
1. Mechatronics, Prof. Pushparaj Mani Pathak | IIT Roorkee
https://onlinecourses.nptel.ac.in/noc21_me27/preview
https://archive.nptel.ac.in/courses/112/107/112107298/
2. Design of Mechatronic Systems, Prof. Prasanna Gandhi, IIT
Bombay
https://onlinecourses.nptel.ac.in/noc21_me129/preview
3. Mechatronics and Manufacturing Automation, IIT Guwahati ,
Dr. Shrikrishna N. Joshi
https://nptel.ac.in/courses/112103174
 Unit-1
Understanding Mechatronics
S. Content Detail P Learning Objectives Teaching Learning Source / Book
No. L aids/Methods
1 Introduction to 2 (i)Understand the concept of Mechatronics, its Black board, PPT, Mechatronics by W
Mechatronics,
interdisciplinary nature, and the integration Video, animation /
Elements of Bolton and
Mechatronics system, of mechanical, electrical, computer science,(i) Lecture
Classification of Mechatronics by Tilak
and control engineering principles. (ii) & (v) cooperative
Mechatronics system,
(ii)Identify and classify the key elements learning strategy - Thakur
constituting a Mechatronics system Jigsaw Method
https://nptel.ac.in/courses
(iii)Analyze and evaluate the components /112107298
involved in designing intelligent

2 Mechatronic system 2 Mechatronic systems. PPT, Mechatronics by W

intelligence, (iv)Comprehend measurement techniques and video, animation / Bolton and
Components involved
in intelligent system control system methodologies utilized in (iii)Lecture / Mechatronics by Tilak
design and Mechatronics. Discussion Thakur
development,
(v)Explore real-world applications of https://nptel.ac.in/courses
Mechatronic systems across various /112107298
industries such as automotive, aerospace,
robotics, healthcare, and manufacturing.
3 Measurements and 2 Understand how Mechatronics principles PPT, Mechatronics by W
control system as a are integrated into practical scenarios to
solve complex engineering problems. video, animation / Bolton and Mechatronics
part of mechatronics
(iv)PBL
system, Application by Tilak Thakur
(i)to (v)
of Mechatronic
Gamification https://nptel.ac.in/courses
systems
(Unit Quiz) /112107298
Input Signal Conditioning Output Signal Conditioning

Intelligent
Smart Sensors Controllers

Intelligent Actuators

Plant

Plant / system
 Matching
Components and
devices for
communication
Analog / Digital Input Signal

Controller (µP, µC,

Sensors Conditioning

FPGA, PLC)
Plant/
System

Analog / Digital Output Signal

Actuators Conditioning

Basic Elements of Mechatronic System

 Mechatronic System (Intelligent )

• A Mechatronics system is a synergistic

integration of mechanical with electrical,
electronics, and intelligent computer
control technologies.
• With the intersection of mechanics,
electronics, and computing, mechatronics
specialists create simpler and smarter
(intelligent) systems.
 Evolution
The term mechatronics was first introduced by
Tetsuro Muri, a Japanese engineer of Yasakawa
Electric Corporation in 1969. However, it was
introduced in academics first in 1996 after related
publication in the refereed and reputed journals of
IEEE and ASME Transactions on Mechatronics.
Evolution of Mechatronic System
 Definitions Of Mechatronics
• In 1996, Yasakawa defined mechatronics as
follows: ‘The word mechatronics is composed
of “mecha” from mechanism and the “tronics”
from electronics’.
• Harashima, Tomzreka, and Kudads defined it
as ‘the synergetic integration of mechanical
engineering with electronics and intelligent
computer control to design and manufacture
industrial products and processes’ in 1996.
• In the same year, Auslandar and Kempf
defined it as follows: ‘Mechatronics is the
application of complex design making to the
operation of physical systems’.
• In 1997, Shetty and Kolk defined it as
follows: ‘Mechatronics is the
methodology used for the optimal
design of electromechanical products’.
• W. Bolton defined it as follows: ‘A
mechatronic system is not just
marriage of electrical and mechanical
systems and is more than just a
control system; it is complete
integration of all of them’.
Individual Integration of Different Disciplines
In
i c s s, Te form
on nic c
hn ati

Sy mo tom olog e
c t r o ol on
r

st de a y
E l e t
c r og

em ll tic
l e
e we ics, y
o

Au chn wa

th ing
icr Po ron s,

eo
te oft AI
M t or s

ry
c r
El Sens ato
e

S
c tu
A

r
Mechatronics

Mechanical
Elements, Electrical
Elements, Machines
Mechanics and
electro mechanics
 Control
Systems

μ-processors Electronic
Controls
Computer Electronics &
Mechatronics Electrical Eng.
Science
Design & Sensors &
Modeling Actuators

Mechanical
Engineering
Key Elements Of Mechatronics
Sensors Response of dynamic
Mechanics of solid system, Root locus
Linear & Rotational Translational and method, Frequency
Acceleration, Force rotational systems, response method, Design
torque and Pressure, Fluid, Electrical
Flow, Temperature, of digital filter, Optimal
Micro and Thermal, Physical control design, NN, Fuzzy,

Ph
nano-sensors Systems State variable method,

mod system
y
Se ctu

s
Intelligent control,

i
ns ato
Actuator

cal
A

e
or rs

l
Identification and control

l
sa

i
Electro-mechanical,

ng
nd
motor, piezoelectric
actuator, Pneumatic n d System
a
and hydraulic, relays Signals
data Mechatronics
a re and
Softw quisition
ac Digital logic, communication
system, fault- direction, logic
and
Data acquisition system, Comp ystem
transducer and measurement system design, asynchronous
e r
s
t

system, A/D conversion and and synchronous sequential

u
logic

D/A conversion, Amplifier and logic, computer architecture

signal conditioning, Computer and microprocessor, system
based instrument system, interface, PLC, Embedded
Software engineering, Data control computer
 Matching
Components and
devices for
communication
Analog / Digital Input Signal

Controller (µP, µC,

Sensors Conditioning

FPGA, PLC)
Plant/
System

Analog / Digital Output Signal

Actuators Conditioning

Basic Elements of Mechatronic System

 • Various components (parts) interact
interdependently such that an output
System corresponding to input is obtained.
• Same or different i/p , o/p in same or
different environment.
Classification of Systems
Single i/p Single o/p • Mechanistic systems
Components
Inside • Ecological systems
Multi i/p
• Social system
Same/ • Animate system
Surrounding Different o/p
Environment
 Climate, river, mountain,
cloud, atmosphere

Society, school,
Mechanisitic System Corporation, etc.

Animate System

Animal, bird,
Machine, conveyer, car,
Human, etc
motor, robot, etc.

Social System

Ecological System
• Mechanistic system purposeless system (no self purpose)
No choice of components it works on physical laws eg. Fountain pens
operate on the principle of capillary action
• Social System:
•Purposeful have defined goals, intentions, or functions. They exist to
fulfill certain societal needs, maintain order, and facilitate human
interactions.
•Choice of Components Exist: People can actively participate in
shaping social structures, norms, and institutions.
• Animate System:
•Purposeful - survival, growth, and reproduction
•No Choice of Components Exist: organs, cells, etc develop according
to genetic instructions and environmental influences.
• Ecological System
•most purposeless system (no self purpose) they follow natural laws
and interactions based on physical and atmospheric conditions.
•choice or adaptation among the components for the overall
balance and functioning of the system
Input Signal Conditioning Output Signal Conditioning

Intelligent
Smart Sensors Controllers

Intelligent Actuators

Plant

Plant / system
 1.Mechatronic System(Intelligent )

People desire to have their most of

SYSTEMS (machine, toys, vehicles, home
ect.) to be Smart and Intelligent enough
,which is Capable to Talk(audio) / Walk(action)
/Report(display) / Inform Etc. as per operating
/functioning Environment and Situations of the
system through UNILATERAL OR
BILATERAL COMMUNICATION link.
1.IC Engine System / Electric
motor with control
2. Power Transmission System /
Drive train – flywheels, clutch,
gear, CVT (Automatic)
3. Brake System - Anti-lock
Brakes and Power Brakes
4. Steering, Suspension and
Tires
5. Electrical System – Battery,
Fuses and Connectors, Car
Computer(ECU)
6. Exhaust System - Catalytic
Converter, Silencer
7. Car Cooling System - water
pump, thermostat, radiator, fan
and other smaller components.
 Sensor translate
measurable quantities
(current, voltage,
temperature, speed,
torque, and flux) into
electric signals through the
interface circuitry.
Signals conditioned to the
appropriate level before
fed into processor.
Then amplified via the
interface circuitry to drive
power devices of the
power converter
 Smart (Intelligent) System

• SYSTEMS: Know the system operation and control parameters.

• ENVIRONMENT AND SITUATIONS: Translate the situation(s)
to respective signal using sensor(s) & transducer(s).
• CAPABILITY to COMMUNICATE: Design for capability to
communicate the translated signal using signal conditioning devices
to controller.
• CONTROLLER: Which controls communication and coordination
among all components through computation and comparison to issue
command signal to implement action.
• ACTION/OUTPUT: Implement controller command using
actuator(s).
 Mechatronics represents a process that blends
. mechanics and electronics with use of precision
engineering, computer science, information
technology, control system theory, and sensor
and actuator technology to design improved
products and processes.
 Classification of Mechanistic Systems
Based on type of input energy, type of control
applied, mathematical model used, and level of
Intelligence.
1. Input Energy based Classification
• Type of input energy - Electrical, hydraulic,
pneumatic, mechanical, chemical, nuclear and
optical
Electrical System Fluid System
Thermal System Chemical System
Mechanical System Nuclear System
 Electrical Systems
• Input is Electrical Energy
• Output may be
Motor
mechanical, electrical,
chemical, etc.

Fan
Transformer
 Thermal Systems
• Input is Thermal Energy
• Output may be
mechanical, electrical,
Furnace
chemical, etc.

Thermocouple
Mechanical Systems Nuclear Systems

• Input is mechanical • Input is nuclear Energy

Energy • Output may be
• Output may be mechanical, electrical,
mechanical, electrical, heat, motion etc.
etc.
Lathe machines Electricity generation
through nuclear fission
Turbines
heat, Nuclear weapons
Automobiles atomic bomb
 Fluid Systems Chemical Systems
• Input is fluid Energy • Input is chemical Energy
• Output may be • Output may be
mechanical, electrical, mechanical, electrical,
etc. etc.

Pelton wheel turbine

Battery
Air compressor
Electrolytic process
Water jet cutting
2. Mathematical Model based Classification
• Equations to establish input-output
relationship
Dynamic System
Static System
Linear System
Nonlinear
Distributed
Lumped
Probabilistic
Deterministic
Dynamic System – the components and system are
represented to give an output with a time constraint.
Represented by integral or differential equation. The
dynamic system depends on past, future or a
combination with present y(t)=x(t-1)+x(t) or y(t) =
x(t+1)
Eg. .An electric circuit containing inductors and (or)
capacitors
Static System - the components and system are
represented to give an output without a time
constraint. y(t)= 2x(t)
Eg. Purely resistive electrical circuits, where the
output is proportional to the input
Linear System - linear relationship
between input and output. Obey the
principle of homogeneity and principle of
superposition.
Amplifiers, Differentiators, Integrators,
Linear electronic filters, Circuits composed
exclusively of ideal resistors, linear
capacitors, inductors (air core or iron core
in linear region), op-amps (in the
"non-saturated" region), and other
"linear" circuit elements
Nonlinear – does not show linear relationship
between input and output
•Circuits that operate in a nonlinear way, such
as mixers, modulators, rectifiers, radio receiver
detectors and digital logic circuits.
•Loads that generate harmonic currents, such
as motor controllers, inverters, welding
equipment, MRI scanner, rectifiers, UPS
systems, computers, printers, TVs and
electronic lighting ballasts.
•Elements that have nonlinear behavior, such
as diodes, transformers, transistors, iron core
inductors, etc.
Distributed – parameters are distributed
along space and time. Developed using
partial differential equation.
Lumped – parameters are functions of time
and are concentrated at a singular point.
Developed using differential equation.
Homogeneous and consistent system can be
lumped not heterogeneous.
Deterministic – Constituted by a unique set
of variable system parameters with previous
state values. Its results are dependent on the
initial values of the variables. Next state can
be perfectly predicted.
• A ball rolling down a slope without any
external forces acting on it.
• A pendulum swinging back and forth.
• A clock ticking.
Probabilistic / stochastic – Constituted
by random variables’ states instead of
unique set of values. Represented using
probabilistic distribution. The occurrence
of events cannot be perfectly predicted.
• The stock market .
• The weather.
• The outcome of a coin toss.
 3. Function based Classification
• Measurement system and control system
Digital data
D0-D7 i/p to CPU
Digital
CH0 Analog data
CH1 data D0-D7
Amplifier CH2
Thermocouple

MULTIPLEXER
+Filter Microprocessor
ADC Or
E/C PPI CS
temperature

Strain Amplifier 8255 A0 Microcontroller

gauge +Filter A1 Or
0 PC0 S/C PLC
RD
Pressure 0 PC1
0 PC2 WR
Machine/ CH7
Plant/ Process/
System Actuator DAC OUT
Final control
S/C : Start Conversion
E/C : End Conversion
Programmable Peripheral Interface (PPI)
AD590 IC (Temp transducer) gives digital output
chip
• Sensor responds to the energy received from
physical quantity. The output is converted to
an electrical analog signal by a transducer.
• Signal conditioner amplification, filtering,
rectification, analog to digital converter
(ADC)/ Digital to analog (DAC), etc.
• Data transmitter data received after signal
conditioning are transmitted to
components/device for further processing for
measurement or control. Important for
computer control or remote control.
• Data Processor (calculation, calibration,
comparison, etc) done by computer /
calculating device for displaying an
output or performing computer control.
• Data presentation data are presented for
interaction through display devices such
as monitors, LCD, prints, etc.
• Measurement system and control system
used to control some phenomenon or action
Types – Open loop or Closed loop system
(i) Open loop system
Power Power
Motor
Supply Converter

Duty cycle of power switches

Signal Conditioning (optocouplers and
System has no
Driver Circuit) feedback of actual
measured value to
(PWM Algorithm)
Keyboard Microcontroller input. Thus o/p of
the system does not
affect the i/p.
(ii) Closed loop system
Speed
measurement
encoder disc

Power Power
Motor
Supply Converter

Duty cycle of power switches

Signal Conditioning (optocouplers and
Feedback
Driver Circuit)
Measured Speed (Nm)
Error
(PWM Algorithm) Counter Digital encoder
+
Microcontroller
- Reference Speed (Nr)

The o/p from the system is feedback to the input level of the
system such that the error is reduced.
Automatic and intelligent mechatronics system are closed
loop and feedback control systems (FCS)
• Closed loop system regulates the output to a certain
value based on the feedback provided by a
measuring device.
• A self regulating system is fully automatic.
• Elements of closed Loop system
i) Elements for comparison :
Error = Desired/set/reference value – measured value

Error is generated by negative feedback, positive

feedback and bipolar feedback.
Negative feedback is used to control a system.
Negative feedback gives a reduced output, positive
feedback gives a increased output value bipolar gives
either of both.
• In control systems, negative feedback is desired for a
number of reasons that are:
• Stability
• Correction of Errors
• Robustness
• Reduces the effects of non-linearity
• Acceptance of Uncertainty
• Reduces Unrestricted Growth
• Controlling System Saturation
• Improvements to Control Performance
ii) Control Elements: Take an action based on the error
signal. Controls the process according to algorithm.
iii) Correction element : Minimize the error based on
the control signal issued by controller. A switch
(effector/ actuator/ final control element) to turn ON or
OFF AC/fan for cooling room.
iv) Process element : Combination of various functions
of different system controlled using closed loop control.
v) Measurement element : Output a value of signal
corresponding to input physical variable parameter
under measurement. Measured value is compared with
required value. Error processed to issue control signal
command for correction.
 Developing closed loop system from
open loop system
Manual control of furnace by operator based on
furnace temperature.
Reference/
desired value
+ Error signal Control µP, Furnace Valve
Furnace System
Amplification PLC, etc (Fuel control)

- Control signal Manipulated

Error signal to fuel valve fuel flow
Measured
temperature
value

Input/ feedback Temperature

signal conditioning transducer

Temperature control of furnace

• Control Unit : Operator behave like a control unit and
control the temperature.
• Correction Unit : Switch to be made ON/OFF of heating
process
• Process : Furnace heated using electricity
• Measuring Device : Thermocouple/ Thermistor, etc.
• Comparison element : Open loop operator compare.
In closed loop feedback control is required
• Reference Value: Desired furnace temperature
• Controlled value : It is the furnace temperature
• Error Signal : Difference between reference and
measured value of temperature. In closed loop human
is replace by computer / PLC/ µP, µC, etc.
 Advantages and Disadvantages of
closed loop control systems
• Advantages:
More accurate, More flexible control, easier
to use, more informative, more intelligent,
more useful than manual control
• Disadvantages:
More complex mechanism, complex
hardware, More prone to breakdown or
damage, Newly developed components may
outdate existing one.
What type of control is used in traffic light
system? How can we convert it from one form
of control to another form?

What are the input and output of a toaster? Is

it an open loop or closed loop system? How can
we transform an open loop system to closed
loop system?

What type of control is used in automatic

washing machine How can we convert it from
one form of control to another form?
Examples of closed-loop control systems in daily life include:
• Automatic Electric Iron – Heating elements are controlled by
the output temperature of the iron.
• Servo Voltage Stabilizer – Voltage controller operates
depending upon the output voltage of the system.
• Water Level Controller – Input water is controlled by the water
level of the reservoir.
• Missile Launched and Auto Tracked by Radar – The direction of
the missile is controlled by comparing the target and position
of the missile.
• An Air Conditioner – An air conditioner functions depending
upon the temperature of the room.
• Cooling System in Car – It operates depending upon the
temperature which it controls.
Examples of open-loop control systems in daily life include:
• Electric Hand Drier – Hot air (output) comes out as long as you
keep your hand under the machine, no matter how much hand is
dried.
• Automatic Washing Machine – This machine runs according to the
pre-set time irrespective of washing is completed or not.
• Bread Toaster – This machine runs as per adjusted time
irrespective of toasting is completed or not.
• Automatic Tea/Coffee Maker – These machines also function for
pre-adjusted time only.
• Timer Based Clothes Drier – Machine dries wet clothes for
pre-adjusted time, no matter how much the clothes are dried.
• Light Switch – Lamps glow whenever the light switch is on
irrespective of light is required or not.
• Volume on Stereo System – Volume is adjusted manually
irrespective of output volume level.
 Mechatronic System Intelligence
• Advancement in Semiconductor technology
and IT let to new generation equipment and
machinery – smart or intelligent product/
device/ system
• Sensing device, memory, data-processing
device, reasoning device, communication
devices and effectors/ actuators
• Artificial Intelligence (AI)
 Properties of Intelligent System
• Unique identification
• Capability to communicate effectively with its
devices and environment
• Capability to store, inform, and use
data/information regarding its components,
system, and environment
• Facility to display its features, requirements, etc.
• Communicate and coordinate with users,
components and environment for decision making
• Continuously monitor their status and
environment
• Perception is the process of interpreting
sensory information from the environment
• Cognition refers to the mental processes
involved in acquiring, processing, and
storing information, such as attention,
memory, language, and problem-solving.
• Execution, also known as action, is the
process of carrying out a task or behavior
based on the information processed by
perception and cognition.
Level of Intelligent Sub system System Components Examples
Intelligence system class ability
Dumb Cannot No Table, glass of
Level 0 interact with components water
self or
environment
Perception + Identification Sensors, Automatic
Level 1 Self regulating execution ( analog and decision iron, Auto
digital signal mechanism + focusing
as effector camera
information) No software
Small SDs/ Perception + Identification Sensors, refrigerator
Level 2 Lower execution +reasoning decision with
Intelligence with for accessing mechanism + thermostat,
knowledge knowledge effector washing
(Opamps, machine
logic gates,
flip flops and
timers)
 Big SDs/ Lower Perception + Identification Sensors, Cars with an
Level 3 Intelligence cognition+ +reasoning decision by electronic
execution for accessing processor transmission
knowledge (Hardware system (ETS)
+Learning+ and [ changing
communicati software)+ road
on effector condition,
ice,
obstacles
etc]
Advance Perception + Identification Sensors, Anthropoid
Level 4 intelligence/ cognition+ +reasoning decision by robots
Wisdom level execution for accessing processor (ASIMO)
knowledge (Hardware
+Learning+ and
communicati software)+AN
on + history N+ Deep
track for Learning
pattern effector
recognition
 Human Intelligence system
• Hardware Components
Sensing Elements
Data processing Elements
End effectors / Actuators
Software components
Future generation system intelligence
level - IoT
Expressing System Intelligence
•Information handling
Intelligence•Problem Reporting
Model 1 Level •Decision making
• Outside the system
Intelligence (service network)
Model 2
Location • Inside the system
(embedded)

Communication • Component(s)
Model 3
uniformity • Container

Expressing System Intelligence

• A container is a software unit that contains all
of the code, system libraries, system settings,
and elements needed to operate in a
computing environment. Containers can be
deployed, and ran wherever needed —
including on personal laptops, private data
centers, or in a public cloud.
 Components Involved in Intelligent
System Design and Development
Type 1 : Mechanical system incorporated
with electronic components in order to
increase the functional aspects of product –
Variable speed Drive, CNC machine
Type 2 : Mechanical product working on
traditional concept, but their internal
components were updated by electronic
parts – sewing machines and automated
manufacturing systems.
Type 3: Products and systems whose
functionality remained similar to those of
traditional, even after replacing internal
part by electronic components – digital
clocks
Type 4: Products and systems working
through synergistic integration with
mechanical and electronic components –
photocopiers, intelligent washers and
dryers, rice cookers, and automatic ovens.
Class category based on JSPMI – Japan society
for promotion of machine Industry (1970 )
• Electrical Components and Systems
• Mechanical components and systems
Information processing components and systems
Basic Hardware Software Soft
components computing
tool
Data, µP, µC, Machine language program For
information, DSP, FPGA, (simple systems), assembly advanced
policies, Computer language program (smart and intelligent
procedures, Computing intelligent systems; 8085, systems :
purposes, devices, 8086, 8051, etc. Fuzzy
communication data microprocessors), high-level Logic, NN,
networks processors, language program (intelligent GA, PSO,
etc complex systems; 8086, 386, etc.
486, Pentium I, II, III, IV), data
processors FORTRAN,
PASCAL, COBOL, BASIC, C,
C++, MATLAB, LabVIEW,
DSpace, etc.
 Mechatronics for all
(Applications of Mechatronics)
Mechatronics has bridged the gap between
traditional/conventional mechanical, electrical, and
control engineering after advances in semiconductor
technology, especially microchips and computer
technology. It responds to the industries’ increasing
demand for engineers who are able to work across
boundaries of conventional engineering. Mechatronic
engineers identify and utilize the interdisciplinary
knowledge and proper combinations of technologies
to provide optimal solutions for increasing engineering
problems.
• Application of such knowledge and technology
leads to the development of more efficient,
intelligent, cost-effective product designs to
meet the growing market demand.
• In particular, the development of microprocessors
and microcomputers encouraged engineers to
integrate interdisciplinary areas and apply them
to various products from all walks of life, such as
in the fields of consumer product design,
manufacturing, instrumentation, motion control,
industrial processes, robotics, aircraft, traction,
defence, automated diagnostic systems,
medicines, and biotechnology
 Application of Mechatronics
• Robotics
• Defence
• Biomedical and Surgery
Robotic Surgery
Laparoscopy
• Agriculture – Automatic Weed controller
• Automation
Industrial Automation
Automation in Automobile Industry
Civil Engineering: Electric Shovel, Building
material mixing and loading ,etc
Metallurgical: Automatic and intelligent
control of metallurgical processes ,etc.
Aerospace: Flight control ,Drone design
,etc.
Chemical: Automatic and intelligent
control of chemical processes, etc
Architecture: Automatic design of a
structure ,3D Printing ,etc.
Medical :Robotic surgery, Biomedicine,etc
Robotics: Snake, ASIMO, SOFIA,etc.
Defense: Guided missile ,tank ,unmanned
vehciles ,etc
Agriculture: Automatic weed controller,
crop plantation ,etc
 8.Bio-mechatronics
*Application of mechatronic approaches in the
field of bio-engineering to design and develop
SMART and Intelligent devices and system for
diagnostics purposes and human/animal organ
replacement and control .
*Doctors and engineers work together to design
and develop such devices and systems
Role of Mechanical ,Electrical & Electronics and
Computer Engineering in Intelligent product
design
• Mechanical:Sensors, Actuators design,
mechanics etc.
• Electrical :Sensors, Actuators design, etc.
• Electronics: Sensors, Controllers
,Communication and switching, interfacing
,networking, etc.
• Computer :Controller , communication,
software design, intelligent control, etc.
THANKS