Scribd
Upload
2 views

LTspice

Uploaded by

Samyak Anand
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
2 views

LTspice

Uploaded by

Samyak Anand
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 7

EE698W

Department of Electrical Engineering, IIT Kanpur

Tutorial on LTspice
1. Adding library file to LTspice editor:
a) Open LTspice and click on .op (right top corner) and type .lib and then click OK.
b) Next right click on .lib two times and then browse for the model file saved in your
machine (PC)

Fig: 1. Opening Command Prompt in LTSpice

Fig 2. Adding Library File or Model file to Editor

2. Changing Transistor Model Name:


a) Select any transistor from component list (lets say nmos4)
b) Ctrl + Right click on transistor
c) Then change NMOS to model name of transistor which was added earlier.
d) Open model file and see name of transistor. Here its CMOSN. Change NMOS to CMOSN
as shown in Fig 3.

EE698W Tutorial on LTspice


e) Cross mark (X) will give you an option to visible that parameter along with the instance
in the editor

Fig 3. Changing Model name of Transitor

3. DC Operating Point Analysis:


a) To perform DC operating point analysis, go to Edit and click on Spice Analysis.
Select “dc op pnt” and type .op (or Simply click on .op (right top corner) and type
.op)
b) Next go to Simulate and click on Run
c) To see the DC operating points, go to View and click on SPICE Error Log
(Shortcut: Ctrl + L)

Fig 4. DC operating point of Transistor and different capacitor definitions

EE698W Tutorial on LTspice


This capacitor definitions can get from Operation and Modelling of MOS
Transistor by Tsividis, 3e - Page No: 416.

4. Performing Parametric Analysis:


a) First define a variable on which you would like to do parametric analysis.
b) Let’s say I would like to vary width of the transistor and define that as w = w1
c) Add command .step param w1 1u 10 2u
d) It means w1 is varying from 1um to 10um with a step of 2um

Fig 5. Example of Parametric analysis command

5. Input and output characteristic of NMOS:


To obtain input characteristics connect the circuit as shown in Fig 6.

Fig 6. Circuit diagram to get input characteristics

a) Go to Edit and click on Spice analysis


b) Go to DC Sweep and enter values of Vgs in 1st Source
c) To get id vs Vgs plot for different values of Vds, enter values of Vds in 2nd Source.
.dc Vgs 0 1V 0.001V Vds 0.8V 1V 0.2V

d) Then Run simulation

EE698W Tutorial on LTspice


e) Select Current of transistor (place the cursor at drain of transistor until you get black
colour probe symbol. It indicates current. If its simple red pen type symbol then it
indicates node voltage)

How to get gm plot from ID vs Vgs plot?


a) Got to Plot Settings and click on Add trace (Shortcut: Ctrl + A)
b) In expression field write d(Id(M1)) and click OK.
c) d() indicates that differentiating a parameter with respect to X-axis, since X-axis
𝑑𝐼𝑑
is Vgs. => = 𝑔𝑚
𝑑𝑉𝑔𝑠

Fig 7. Plotting gm from ID vs Vgs plot

EE698W Tutorial on LTspice


To obtain output characteristics of Fig 6, add command as follows
a) Go to Edit and click on Spice analysis
b) Go to DC Sweep and enter values of Vds in 1st Source
c) To get id vs Vds plot for different values of Vgs, enter values of Vgs in 2nd Source.
.dc Vds 0 1V 0.001V Vgs 0.6V 0.8V 0.1V

d) Then Run simulation and Select Current of transistor


e) gds plot can be obtained from ID vs Vgs by doing as follow
→ Press Ctrl+A and write d(Id(M1))
→ Then you will get plot gds vs Vds

6. Obtaining gm vs Current density plot:


Connect the circuit and enter the commands as shown in Fig 8

a) Command .param is used to assign value to defined variable.


b) Here, sweeping parameter is I0 (Id/w1 = Current density) and it will come in X-axis.

Fig 8. Circuit diagram to characterise NMOS

c) Run the simulation


d) Press Ctrl + A and write d(Id(M1))/d(V(vgs)) in expression field. Then you will get
gm vs Current density.
e) Suppose if you write simply d(Id(M1) in expression field, that means you are
differentiating Id of M1 transistor with respect to Current density.

EE698W Tutorial on LTspice


Fig 9. Plotting gm with respect to current density

7. Noise Analysis:
Output Noise voltage of transistor can be plotted as follows

a) Go to Edit and click on Spice analysis


b) Go to Noise and write V[Vout] in Output field. Here, at the drain of transistor we
would like to find noise voltage. Node voltage should keep inside the V[]
c) Enter input voltage, since Vgs
d) Select type of sweep and enter frequency range (let 1Hz to 10G with 50 per decade)
e) The overall command will be as follows
.noise V[Vout] Vgs dec 50 1 10G

EE698W Tutorial on LTspice


f) Run the Simulation and select Vout the
g) Export the plot to text file and plot it in Matlab or simply right click on Y-axis of
the plot and change it to logarithmic.

Fig 10. Output noise voltage at drain of transistor.

Note:

→ You can export the plot to text file and then can plot it in Matlab. Refer Fig 11
→ Select the parameters which you want to export

Fig 11. Exporting different plots to text file

EE698W Tutorial on LTspice

You might also like