DIGITAL READOUTS

Operation Manual
2007.5.19

SINO L . DIGITAL LTD

 Dear Users:
Thank you for your purchase of the SINO Digital Display Meter, of
which the main purpose is provide detection and positioning functions
for machine tool processing. Before use, please read the following
safety instructions and precautions for safety operation of the new
digital display meter device.
When using the manual:
• • Chapters and sections are listed in the table of contents( see P5~6
ahead).
• • •This
• manual includes some instructions for panel keys of SDS6 digital
display meter and other series, including.
the readout used for 2 axis milling machine and
SDS6-2V
grinding machine and lathe machine
the readout used for 3 axis milling machine and
SDS6-3V
lathe machine and discharging processing

It is recommended that:
• • • •Instructions for panel keys of the SDS6 digital display meter that is
applicable to this manual are listed in P1~4 of the above Section 1.
• • Read through follow safety precautions and Section 2( see
P100~104), which are very important to the safe operation of your digital
display meter.

Safety Precautions:
Caution:
• • Do not dampen or splash coolant directly onto the unit to avoid electric
shock or fire.
Warning:
• • • •Do not open the enclosure optionally to avoid electric shock, there is no
element repairable by the user inside. Turn to appointed technician for
repair.
• • • •If the unit is not used for along time, the chargeable lithium batteries for
data retention inside the digital display meter will be damaged. Please
contact SINO Company, agent or professional technicians for battery
 replacement when using it again.
Notes:
• • • •Disconnect power plug promptly if the digital display meter emits smog
or peculiar smells, when an electric shock or fire may be caused when
continuing to use it. Please contact SINO Company or dealer and never
attempt to repair it by yourself.
• • • •The digital display meter constitutes a precision detection device with an
optical electronic ruler. Once the connecting wires between the two parts
are broken or damaged of surface during use, error in detection data
might be caused, to which the user should pay special attention.
• • • •Do not repair or refit the digital display by yourself, otherwise a fault or
damage might be caused. In the case of abnormality, please contact SINO
Company or dealer.
• • • •Once the optical electronic ruler used in the digital display meter is
damaged, do not replace it with rulers of other brands, because products
of different companies have their respective characteristics, indicators
and wiring. Never make wiring without the guide of professional
technicians, otherwise the digital display meter might get into fault.
This digital display device conforms to the Standard-European
Electric Appliance Safety CC Standard.

Our company is awarded the certification of ISO9001 International

Standard Quality System(Ver. 2000) issued by the British Would
Company (an international Certifying company)

Awarded the manufacturing permit “ 00000174” for measuring

instruments issued by the Government of China.
 Illustration of Panel and Keyboard

••••••••••••••••••••••••••••••••••••

SEL
• •
• • ••
SEL
•• ••
•• • •

SEL •• •• •• • •
••
•• •• • • ••
••

•••••••••••••••••••••••••••••••••••

SEL •
• •
• • ••
SEL
• •• ••
•• • •
•
•• •• •• • •

• ••
•• •• • • ••
••

1
 Illustration of Panel and Keyboard

Caption of the Keyboard of SDS6

Keys for Axis selection

•• •• •• •• ••
Entry keys for digits
5 6 7 •• 9

•• •• × ÷ = Operation Key (in Calculation

function key)

Calculation function key

(in Calculation function key)

Input (calculation result)

canceling key(in Calculation
function key)

Key for “Inverting”

TrigonometricFunctions
(in Calculation function key)

—
Square root calculating key
(in Calculation function key)

Entry keys for decimal point

• •
Entry key plus or minus symbol

Key for entering data

2
 Illustration of Panel and Keyboard

Key for cleaning the displayed

value to zero

Function key for getting one half

Key for the conversion the

meter System/ British system
display

Function key for Sleep

Function key for 200 zero

Position

••

R angular ARC function key

(ARC Function key)

Function key for circle equally

Dividing (PCD Function key)

Function key for drilling holes

along an oblique line

Angular surface processing

function key; In calculation
function as sine trigonometric
function key

Progressive inner chamber

processing function key; In
calculation function as cosine
trigonometric function key

3
 Illustration of Panel and Keyboard

Tool compensation function key;

In calculation function as
tangent trigonometric function
key

Key for the conversion of

relative/absolute display

Key for the selection of

upper/lower term or plane
procession

Key for taper measure function

Key for calling 200 tool

storeroom

TOOL
Key for input 200 tool storeroom
Key for radius

Function key for machine output

(EDM)
• o• nly SDS6-3V readout has• •

Function key for data filtration

• •only SDS6-2V readout has• •

4
 Catalogue

Catalogue

A. Basic Functions …………………………………………………………. 1

B. Smooth R ……………………………………………………………….. 15
(Be the same with: MIIL_MS • MIIL_M)

C. Simple R ………………………………………………………………... 27
(Be the same with: 2V-MIIL_MS • 2V-MIIL_M)

D. Hole Drilling Along An Oblique Line ………………………………… 34

(Be the same with: MIIL_MS)

E1. The Function For 200 Point Subsidiary Zero Position ……………... 38
(Be the same with: MIIL_MS• MIIL_M• EDM)

E2. The Function For 200 Point Subsidiary Zero Position ……………... 47
(Be the same with: LATHE)

E3. The Function For 200 Point Subsidiary Zero Position ……………... 55
(Be the same with: 2V-GRIND)

F. PCD Circle Equally Dividing Holes …………………………………... 62

(Be the same with: MIIL_MS• MIIL_M• EDM)

G. Angular Surface Processing ……………………………………………66

(Be the same with: MIIL_MS)

H. The Function-Calculator Function ………………………………….. 71

(Be the same with: MIIL_MS)

5
 Catalogue

I. Tool Diameter Compensation ………………………………………… 74

(Be the same with: 3V-MIIL_MS)

J. 200 Tool Storeroom……………………………………………………. 77

(Be the same with: LATHE)

K. The Function Of Measure For Taper ……………………………….. 81

(Be the same with: LATHE)

L. (EDM)Matching Output Function ………………………………….. 83

(Be the same with: 3V-EDM)

M. Digital Filter Function ………………………………….…………… 93

(Be the same with: 2V-GRIND)

N. N3 Function ………………………………….…………….. …………95

(Be the same with: 2V-MIIL_MS)

O. The Progressive Progressing of rectangular Inner chamber ………. 99

(Be the same with: 2V-MIIL_MS)

P. Additional sheet……………………………………………………….. 102

6
 A. Basic Function

A.

Basic Functions

1
 A. Basic Function

We take pleasure to tell you that this machine tool optical digital display ruler
device you are using is the one most popular in Europe.
You will be able to use this device easily after you have read this manual
thoroughly. Thank you!

I. Usage

1. Start, Self check Model

1) Selecting the power voltage, SEL

switching the power on Special mark for

milling machine
Number of axes SEL

2) Self check of the meter

SEL

Display resolution

3) Self check finished, SEL

Message screen displays

enter working mode "ALE" or "INC" or "ZER"
SEL

Note: Two axial readout only has

X-axis and Y-axis, three axial
SEL

readout has X-axis, Y-axis and Z-axis. The lathe machine readout
display “LATHE”; the grinding machine readout display “GRIND”;
the multifunctional milling machine readout display “MILL_MS”; the
universal milling machine readout display “MILL_M”; the discharging
processing readout display “EDM”.

2. Setting of System
In process of self check, key , then the system enter setting mode after self
check finished.
1) Setting axis X resolution. SEL

Setting different resolution according to keying different numbers.

Number key 0 1 2 5 7 8 9
Resolution(um) 10 1 2 5 0.1 0.2 0.5
Key , next step

2) Setting axis Y resolution.

Setting method alike axis X SEL

Key , next step

3) Setting axis Z resolution.

Setting method alike axis X. SEL

2
 A. Basic Function

Key , next step

4) Setting counts direction of axis X linear encoder.

Key • • as positive direction count. SEL

Key •• as reverse direction count.

Key , next step

5) Setting counts direction of axis Y linear encoder.

Setting method alike axis X.

Key , next step

SEL

6) Setting count direction of axis Z linear encoder.

Setting method alike axis X.
SEL

Key , next step

7)choose machine type

SDS6-3V readout• •
• • multifunctional milling machine readout

• • universal milling machine readout

• • discharging processing readout

• • lathe machine readout

SDS6-2V readout• •
•• multifunctional milling machine readout
• • universal milling machine readout

• • grinding machine readout

• • lathe machine readout

key • •next step

8)choose whether integrate Y-axis with Z-axis

press • • or • • can realize the conversion
“NONE” means no integration
“INGREAT” means integration and the integrated

3
 A. Basic Function

value displays in Y-axis LED.

Press • n• ext step
Note: only 3 axis lathe machine has this function.

9) choose compensation type

• • choose line error compensation “LINEAR”;

• • choose Segmented error compensation “SEGMENT”;

Press • n• ext step

10) Self test.

Key twice, the Self-test program started ALE

then key to quit.

(Note: Setting of axis Z only applies to three axis digital readout.)

3. Returning the displayed Value to zero

1) It is possible to return to zero any
point, take the example of X axis SEL

display.

2) Key SEL

4. Presetting data
A B C
1) As shown in the figure, after the processing
of Hole A finished, the position of the
working piece has been adjusted, Hole B
is to be processed.
••
••••
2) Align the Tool with Hole A. ••••

3) Select the key for axis, key .

SEL

4) Key 5 ,Enter the value(If the entered value

is wrong, key and enter the correct one
again) SEL

5) Key , (If any mistake is found now, repeat

SEL

4
 A. Basic Function

steps 3~5).

6) Move the machine table to the position

of 13, and the processing at Point B can SEL

start.

5. Absolute/relative/user coordinate display

mode. D

10
C E

Key , the absolute/relative display 10

B

20
mode will convert one the other, following are A

10
M
10
operations. 30
50

1) Let the Tool point to Point M

reset under the absolute mode. SEL

Key or
Key
SEL

2) Move the machine tool to

Position A.
SEL

SEL

3) Move the machine tool to

Position. B. SEL

SEL

4) Key
SEL

SEL

5) Move the machine tool to

Position C. SEL

SEL

6) Move the machine tool to

Position D. SEL

SEL

7) Return to the absolute mode SEL

SEL

5
 E2. The Function For 200 Point(Be the same with: LATHE)

E2

The Function For 200 Point

Subsidiary Zero Positions
(Be the same with: LATHE)

47
 E2. The Function For 200 Point(Be the same with: LATHE)

200 subsidiary zero position function:

200 auxiliary zero position function: also is called 200 user Coordinate
System(UCS) function.

ALE: Absolute Coordinate System.

ALE is the “reference” system. All 200 UCS are defined relative to the ALE.
ALE is confirmed in the initialization of the work piece process, which doesn’t
change if the work piece no changed.
UCS: User Coordinate System.
In the processing of moulds, often it would not work with only one reference
zero position, normally, a lot of subsidiary zero positions is necessary. In the
processing of a large or medium lot of complicated drilling/milling fittings with
multi point dimensions, it is also necessary to have a lot of fixed point positions in
order to perform the processing of a series of structures with dimensions referred
to these point position. In these cases, if there is only one reference point, the
working efficiency will be rather low, as you have to find out the correct position
point by point, more over, it may be very difficult for complicated moulds or
molding fittings to do in such a way. The function 200 point subsidiary zero
positions is specially provided as a good resolution for this problem.

• . The operator must know the following two key points before
making use of this function.
1. Every subsidiary zero position is equivalently the original point of one UCS.
Once entering the display mode of such UCS, the display of every point will
take the subsidiary zero position as the original point.
2. There is relation between every subsidiary zero position and the zero position is
the absolute mode. After a subsidiary zero position is set, it will keep the
position relation between it and the zero position in the absolute mode in
memory, once the zero position in the absolute mode changes, the subsidiary
zero position will also change by the same distance and angle.

• . The operator may fully make use this function as the

following:
1. Set the zero position in absolute mode (ALE lamp on) at the main reference
point of the working piece, for example, Point O in Fig. (1) in next page. Set
subsidiary zero positions at subsidiary reference points of the working piece, for

48
 E2. The Function For 200 Point(Be the same with: LATHE)

example, Points 1• 2• and 3 in Fig. (1). It is possible to enter the display mode of
every UCS taking a subsidiary zero position as its original points to perform the
processing when need.
2. In the display mode of every UCS, processing with various special function can
be performed.

• . The setting of subsidiary zero position

There are two methods of setting subsidiary zero position: the one is entering
the position of the subsidiary zero position directly, the other is resetting once a
subsidiary zero position is reached.
Method 1: Directly Entering, under the UCS display mode, key
Number keys .
Take Fig. (1) as example: After turning the machine on, move the machine
tool to the center point O in Fig.(1), Enter the absolute display mode.
••••••••••••

Y/Z
• •71
• •40

• •40
• •60

• •20

40

• • • • • • • • • • • • • • •25
••
70 ••
10 • • • • • • • • • • • • • •••••••••••••• • • • • • • • • • • •
155 Fig. (1)

In the following content take Y axis as an example

Reset, set the zero position in the absolute mode at the main reference of the
working piece.
SEL

Z
Z0
SEL

1) After setting the zero position in the absolute mode, the system automatically
perform a keeping in memory operation, in order that once a power interruption
happen in the course the zero position may be tracked back.

49
 E2. The Function For 200 Point(Be the same with: LATHE)

2) Enter the UCS display mode. (Two Method)

Method 1:
Key
Key

Method 2:
Key
Key ••

3) Enter the position of the first subsidiary zero position.

Key •• ••

• • 7 ••

4) Enter the position of the second UCS.

Key or
Key ••

5) Enter the position of the second zero position.

Key •• ••

• • •• •• ••

6) Enter the display mode of the third UCS.

Key or
Key ••

7) Enter the display mode of the third zero position.

Key •• ••

• • •• •• ••

The setting of all the subsidiary zero positions of the working piece shown in
Fig. (1) has been finished.

50
 E2. The Function For 200 Point(Be the same with: LATHE)

Why the direction of each coordinate of your input auxiliary zero position
opposite to that of the display result? As the above example illustrates, under the
user coordinate display mode, if your enter the coordinate of auxiliary zero
position on the position of the zero position under absolute state, the display result
will be the position of absolute state zero position in this user coordinate. Because
the user coordinate display mode uses each auxiliary zero position as the origin of
user coordinate. Seeing from Fig. 1, Point O is exactly located at the position of
Point 1(-20, 70), the position of Point 2 (-30, 120) and that of to Point 3 (-20, 130).
If the operator enters the coordinate of auxiliary zero point at any other point than
the zero point under absolute state, the display result will be the position of this
point in this user coordinate.
Method 2: Clearing when the position is reached. When the machine tool is at
the position of the subsidiary zero point, key .
Method 2 is not suited to operations on lathe. The instructions for lathe are
not given in details in this manual.

• . The usage of subsidiary zero positions.

After entering the display mode of the UCS, the corresponding subsidiary
zero positions may be used to help in the processing.
It is possible to enter a UCS display mode using key • • or .
When using keys and , you may key or continuously until
entering the desired UCS.
When using key just key and under the prompt “ZERO No” enter the
number of the desired UCS. For the related operations, the operator may refer to
“5 Absolute/relative/user coordinate display mode” under “• •.Usage” of “A. Basic
Function”.
Take the spare part shown in Processing Fig. (2) as an example, operator can
use the 200 point auxiliary zero-point function in grinding and turning.

51
 E2. The Function For 200 Point(Be the same with: LATHE)

••••••
•••••• •••••• ••••••••••••
Y/Z

• •••
• •••

• •••

• •••

• •••
•• •• ••••
••••••• •• •••• ••
••••••
Fig.(2)
The work piece has been roughly turned, and has to be semi subtly turned.
The unilateral allowance through rough turning is 0.05, the subtle turning
will the surface of the work piece to meet the roughness requirements.
First set the absolute coordinate origin at Point A, then directly the position
of the auxiliary zero point according to the setting method I for auxiliary zero
point to set up the user coordinate system. We have set the first auxiliary zero
point at the point (10, -40), the second at the point (20.05, -70) and the point
(30.05, -120).

1) After checking the cutting tool, enter the first user coordinate system.

Key

2) Enter the code

Key • • SEL

3) Process the encircle • •20

Start cutting until the displays on

both X axis and Y turn out 0.

4) Enter the second user coordinate system.

Key

52
 E2. The Function For 200 Point(Be the same with: LATHE)

5) Process the encircle • •40

start cutting until the displays on
X axis and Y turn out 0.

6) Enter the third user coordinate system.

Key

7) Process the encircle • •60

Start cutting until the displays on

X axis and Y turn out 0.

8) Return to absolute state

Keep pressing until “ALE” is
displayed.

9) Switch the work piece to the other side of its, for turning of such other end
encircle • •40.

• . The Clearing of Subsidiary Zero Positions and Other

Related Problems.

1. The Clearing of Subsidiary zero positions

In absolute state (ALE state), key 10 times continuously, the memory
about all the subsidiary zero positions will be cleared, the 200 subsidiary zero
positions will become the same point of the zero position in the absolute state.

53
 E2. The Function For 200 Point(Be the same with: LATHE)

2. Reset during a subsidiary zero position is being used

A subsidiary zero position is being used of course under the display mode of
the corresponding UCS, resetting in this state is actually to reset a new subsidiary
zero position. The point at which the resetting operation act become the new
subsidiary zero position, and the new subsidiary zero position replacing the
original subsidiary zero position.

3. Turn to one half during a subsidiary zero position is being used

“1/2” function may be used under UCS display mode. Turning to one half
under the UCS display mode using a subsidiary zero position is actually also
resetting a new subsidiary zero position. After the operation of turning to one half
act, the original subsidiary zero position will be replaced by the new subsidiary
zero position is center between the original subsidiary zero position and the point
at which the operation act.

54
 J. 200 Tool Storeroom(Be the same with: LATHE)

J.

200 Tool Storeroom

(Be the same with: LATHE)

77
 J. 200 Tool Storeroom(Be the same with: LATHE)

200 tool storeroom:

It will need to use different tools when turning different work pieces or
different surface of work pieces, so it is necessary to uninstall and adjust the tools,
SDS6 digital readout has the function of 200 tools storeroom, which makes the
operation simple.

Notice: The function of 200 tools storeroom can’t be used but the lathe has
the frame of adjusting tool. Please don’t use this function if you
haven’t the frame of adjusting tool.

1. Set a base tool. In the state of “ALE”, ••••

••••
to clear the display value of the X axis Tool 1
Tool 2
or the Y axis when moving the base Base Tool

•••

•••
tool to touch the frame of adjusting tool.

2. Ensure the other tool position relative to

the base tool position, which is also the zero ••••••
point of “ALE” coordinate system, as the figure (a) shows, the relative position
of the second tool is:
X-axis 25-30=-5, Y-axis 20-10=10.

3. Number the tool, and store the relative position to the base tool into the
digital readout.

4. In process, the operator can input the numbers

of using tool, the digital readout will display
••

the relative position dimension of using tool

to the zero point of “ALE” coordinate system,
Tool 1
moving the lathe platform to make the Tool 2
••••
display of X axis and Y axis become zero.

5. The tool storeroom can store datum of 200

tools.
Tool 2

6. If the function of 200 tools storeroom is opened, you can lock this function after
you continue to touch the key • • 10 times.

If the function of 200 tools is locked, you can unlock this function after you
continue touch the key • • 10 times. In the state of “ALE”.
Means close tool storeroom• •
Means open tool storeroom• •

78
 J. 200 Tool Storeroom(Be the same with: LATHE)

Notes: the Y-axis value mentioned above is the integrated value of Y-axis
with Z-axis, namely the Z/Z0-axis in the former lathe machine readout.

The operation of inputting the datum of tools and calling tool:

1) Please input the datum of tools, in the X

“ALE” coordinate system, clear the

Y
display value when moving the base
tool to touch the frame of adjusting tool, Z
set the first tool to the base tool.

2) Enter the inputting stare.

Key TOOL

3) Input the datum of next tool. X

Key ••
Y
••

Key

4) Input the numbers of tool

Key • •

Key

5) Input the datum of tool. X

Key • • 5
Y
•• ••

6) Key continue to input the datum of next tool.

Key TOOL quit the inputting state.

You can operate the tool storeroom as below after you input the datum of
tools, first install the second tool.

1) Enter the using state. SEL

Key

2) Ensure the base tool. SEL

Key

79
 J. 200 Tool Storeroom(Be the same with: LATHE)

Default the first tool as the base tool, you

can also set the other tool as the base tool, key number is OK. Key
can call other tools.
3) Call the second tool. SEL

Key ••

X
4) Exit ALE

Key ALE
Y

Move the flat-from to make the display value of X axis and Z/Z0 axis become
zero.
The second tool has reached the datum mark, in like manner, the operator can
input and call 200 tools.

Notice: You can clear the display value to zero in “ALE” coordinate system
only when using the base tool, you can clear the display value to zero
in “INC” coordinate system when using other tools.

80
 K. The Function Of Measure For Taper(Be the same with: LATHE)

K.

The Function Of Measure For Taper

(Be the same with: LATHE)

81
 K. The Function Of Measure For Taper(Be the same with: LATHE)

The Function of measure for taper: 90

0 10
90
0 10

80

80 20

20
70

70
30

30
The taper of work piece can be measured
40 40
60 60
50 50

when turning the taper work piece.

A B
AB

Operation:
As figure shows, the nod of lever meter
is touched the position A of work piece surface. 60• 8.5
•
Pressing it to make the lever meter point to zero. A
B

4.907
1) Then entering the function of measure
for taper.
X
Key ALE

Y
ALE

2) Move the lever meter to position B of X

work piece surface, press it to make the ALE

lever meter point to zero. Y

ALE

3) Compute. X
ALE

Key ALE
Y

The display value of X axis is taper.

The display value of Y axis is angle.

4) Quit
Key

82
 Additional sheet

Additional sheet:
• . What the user must know:
1. The digital display box must be handle carefully.
2. The box must be grounded properly.
3. Power voltage selection: AC 80V~260V ±15%
50 Hz~60 Hz
4. Power consumption: 25VA
5. Working temperature: 0• •~45• •
6. Storage temperature: -30• •~70• •
7. Relative humidity: <90%(20±5• )•
8. Weight: 3.2 kg
9. There must not obviously be corrosive gases around the box.
10. Number of coordinates: 2 coordinates, 3 coordinates.
11. Display: 7 digit with plus and minus symbol display (2 axes or 3 axes),
the message window displays by means of 8 star character
display device.
12. Frequency multiplication: 4X
13. Allowable input signal: TTL square wave.
14. Allowable input signal frequency: • •5M Hz
15. Length resolution: 5µm, 1µm,10µm, 0.1µm, 0.2µm, 0.5µm.
16. Operation keyboard: Sealed diaphragm touch keys.
17. Optical Ruler: Grating aperture: 0.02 mm; power voltage: +5V; signal:
TTL square signals are send out from two channels with
aphase difference of 90° (with zero position signal);
current: 50 m A; accuracy: ±3µm, ±5µm, ±10µm.

• . Trouble shooting and handling:

102
 Additional sheet

Troubleshooting of Grating Ruler and Digital display Meter

The following troubleshooting is primary only. If there are still
problems, do not dismantle them by yourself, seek help from our company
or corresponding agents.

Symptom of
Source of failure Troubleshooting
failure
Digital 1. Is it connected to power 1. Check power wire, then
display supply? switch on power supply.
meter does 2. Is power switch closed? 2. Close the power switch.
not display 3. Is appropriate mains voltage 3. Mains voltage should be
used? within 60~260V.
4. Shorting of power supply 4. Disconnect plug of grating
inside grating ruler. ruler.
Enclosure 1. Is enclosure of machine tool 1. Well ground enclosure of
of digital and digital display meter well machine tool and digital
display grounded? display meter
meter is 2. Is there electric leakage from 2. Check 220V power supply.
charged. 220V power supply to the
ground?
1. Exchange with the grating 1. If counting is normal failure
ruler on the other axis, and of grating ruler.
then operate to see if it no If counting is abnormal failure
longer counts. of digital display meter.

One axis of
digital
display
meter does 2. Is digital display meter in 2. Exit special function.
not count. some special function?

103
 Additional sheet

Symptom of
Source of failure Troubleshooting
failure
Grating 1. Grating ruler falls outside the 1. Repair the grating ruler.
ruler does usable range of length,
not count reading head cracked up.
2. Reading head of grating ruler 2. Repair the grating ruler.
rubs ruler enclosure, and
aluminum chips piled up.
3. Too much gap between 3. Repair the grating ruler.
reading head of grating ruler
and ruler body.
4. Metal hose parts of grating 4. Repair the grating ruler.
ruler (plugs, hoses,
connectors) burnt, squeezed,
broken to cause shorting or
breaking of inner circuits.
5. Time of service of grating ruler 5. Repair the grating ruler.
too long, some inner parts or
components go wrong.
1. Carriage body of grating ruler 1. Repair the grating ruler.
apart from friction ball.

2. Some part of small grating 2. Repair the grating ruler.

piece inside reading head of
grating ruler wears out.
Grating
ruler does
not count 3. There is dirt on some part of 3. Repair the grating ruler.
sometimes. grating inside enclosure of
grating ruler.

4. Insufficient elasticity of 4. Repair the grating ruler.

carriage steel wire inside
reading head of grating ruler.

104
 Additional sheet

• . Structural principle
Our linear encoder and digital readout are high technologic
production that is combined with photo electronic technology, precision
mechanical technology, microelectronic technology and computer
technology, and so on. The customer without being trained may not repair
this system. The structural principle is as follows.

Produce pulse Counter Enter digital

Move Digital
by phonics pulse of readout
linear principle readout
position

Disposal Display
value of position dimension
counter

• . Install figure
1.old DRO Install figure
1 19 280
1 65

4 3.2
270

491
52

105
 Additional sheet

2.new DRO Install figure

50 308

193
301

36
53.5

52 456

notice: 1• •cliping the power and signal wire to avoid stumbling.

2• i•nstall height is 1350mm from the operator standing floor.

• •. product packaging bill

1• a
• piece of SDS6 series digital readout
2• a
• piece of power wire
3• a
• copy of operating instruction
4• A
• copy of verified certificate
5• A
• piece of dustproof cover
6• a
• piece of wire clip
7• a
• piece of bracket

106
SINO L . DIGITAL LTD http//:WWW.Sino-ld.com
Service on-line: 020-81591008