ELECTRICAL & POWER CONTROL

SECTION
BODY CONTROL SYSTEM
BCS B

E
CONTENTS
BASIC INSPECTION .................................... 3 DOOR LOCK : CONSULT-III Function (BCM - F
DOOR LOCK) ..........................................................16
INSPECTION AND ADJUSTMENT ..................... 3
REAR WINDOW DEFOGGER ...................................17
ADDITIONAL SERVICE WHEN REPLACING G
REAR WINDOW DEFOGGER : CONSULT-III
CONTROL UNIT .......................................................... 3 Function (BCM - REAR DEFOGGER) .....................18
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Description .................................. 3 BUZZER .....................................................................18 H
ADDITIONAL SERVICE WHEN REPLACING BUZZER : CONSULT-III Function (BCM - BUZZ-
CONTROL UNIT : Special Repair Requirement ...... 3 ER) ..........................................................................18

INT LAMP ...................................................................18 I

TRANSIT MODE CANCEL OPERATION ........... 4
Description ................................................................ 4 INT LAMP : CONSULT-III Function (BCM - INT
Work Procedure ........................................................ 4 LAMP) ......................................................................19
J
HEADLAMP ...............................................................20
SYSTEM DESCRIPTION .............................. 5
HEADLAMP : CONSULT-III Function (BCM -
BODY CONTROL SYSTEM ................................ 5 HEAD LAMP) ...........................................................20
K
System Description ................................................... 5
WIPER ........................................................................22
Component Parts Location ........................................ 6 WIPER : CONSULT-III Function (BCM - WIPER)....22
COMBINATION SWITCH READING SYSTEM FLASHER ...................................................................23 L
..... 7 FLASHER : CONSULT-III Function (BCM -
System Diagram ........................................................ 7 FLASHER) ...............................................................23
System Description ................................................... 7 BCS
INTELLIGENT KEY ....................................................24
SIGNAL BUFFER SYSTEM ...............................11 INTELLIGENT KEY : CONSULT-III Function
System Diagram ...................................................... 11 (BCM - INTELLIGENT KEY) ....................................24
System Description ................................................. 11 N
COMB SW ..................................................................27
POWER CONSUMPTION CONTROL SYS- COMB SW : CONSULT-III Function (BCM -
TEM ....................................................................12 COMB SW) ..............................................................27 O
System Diagram ...................................................... 12
System Description ................................................. 12 BCM ...........................................................................28
Component Parts Location ...................................... 14 BCM : CONSULT-III Function (BCM - BCM) ...........28
P
DIAGNOSIS SYSTEM (BCM) ............................15 IMMU ..........................................................................28
IMMU : CONSULT-III Function (BCM - IMMU) ........28
COMMON ITEM ......................................................... 15
COMMON ITEM : CONSULT-III Function (BCM - BATTERY SAVER .....................................................29
COMMON ITEM) ..................................................... 15 BATTERY SAVER : CONSULT-III Function (BCM
- BATTERY SAVER) ...............................................29
DOOR LOCK ............................................................. 16

Revision: 2011 November BCS-1 2011 G Sedan

TRUNK ...................................................................... 30 COMBINATION SWITCH INPUT CIRCUIT ....... 39
TRUNK : CONSULT-III Function (BCM - TRUNK)... 30 Diagnosis Procedure ............................................... 39
THEFT ALM .............................................................. 30 COMBINATION SWITCH OUTPUT CIRCUIT ... 41
THEFT ALM : CONSULT-III Function (BCM - Diagnosis Procedure ............................................... 41
THEFT) ................................................................... 31
ECU DIAGNOSIS INFORMATION ............. 43
RETAIND PWR ......................................................... 31
RETAIND PWR : CONSULT-III Function (BCM - BCM (BODY CONTROL MODULE) .................. 43
RETAINED PWR) ................................................... 31 Reference Value ..................................................... 43
Wiring Diagram - BCM - .......................................... 67
SIGNAL BUFFER ...................................................... 32
Fail-safe .................................................................. 73
SIGNAL BUFFER : CONSULT-III Function (BCM
DTC Inspection Priority Chart ............................... 75
- SIGNAL BUFFER) ................................................ 32
DTC Index .............................................................. 76
AIR PRESSURE MONITOR ...................................... 32
AIR PRESSURE MONITOR : CONSULT-III Func-
SYMPTOM DIAGNOSIS ............................ 79
tion (BCM - AIR PRESSURE MONITOR) ............... 32 COMBINATION SWITCH SYSTEM SYMP-
DTC/CIRCUIT DIAGNOSIS ......................... 34 TOMS ................................................................. 79
Symptom Table ....................................................... 79
U1000 CAN COMM ............................................ 34
Description .............................................................. 34
NORMAL OPERATING CONDITION ................ 80
Description .............................................................. 80
DTC Logic ............................................................... 34
Diagnosis Procedure .............................................. 34 PRECAUTION ............................................ 81
U1010 CONTROL UNIT (CAN) ......................... 35 PRECAUTIONS ................................................. 81
DTC Logic ............................................................... 35 Precaution for Supplemental Restraint System
Diagnosis Procedure .............................................. 35 (SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
U0415 VEHICLE SPEED ................................... 36 SIONER" ................................................................. 81
Description .............................................................. 36
REMOVAL AND INSTALLATION .............. 82
DTC Logic ............................................................... 36
Diagnosis Procedure .............................................. 36 BCM (BODY CONTROL MODULE) .................. 82
Exploded View ........................................................ 82
B2562 LOW VOLTAGE ..................................... 37
Removal and Installation ......................................... 82
DTC Logic ............................................................... 37
Diagnosis Procedure .............................................. 37 COMBINATION SWITCH .................................. 83
Exploded View ........................................................ 83
POWER SUPPLY AND GROUND CIRCUIT ..... 38
Removal and Installation ......................................... 83
Diagnosis Procedure .............................................. 38

Revision: 2011 November BCS-2 2011 G Sedan

 INSPECTION AND ADJUSTMENT
< BASIC INSPECTION >
BASIC INSPECTION A
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
B
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description
INFOID:0000000006211041

Perform the system initialization when replacing BCM, replacing Intelligent Key or registering an additional C
Intelligent Key.
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Re- D
quirement INFOID:0000000006211042

Refer to the CONSULT-III operation manual for the initialization procedure.

E

BCS

Revision: 2011 November BCS-3 2011 G Sedan

 TRANSIT MODE CANCEL OPERATION
< BASIC INSPECTION >
TRANSIT MODE CANCEL OPERATION
Description INFOID:0000000007868415

• BCM is in transit mode if turn signal indicator on combination meter turns ON for 1 minute when ignition
switch is turned from OFF to ON.
• In this case, cancel operation must be performed.
NOTE:
Do not cancel transit mode during storage of the vehicle. Always cancel transit mode before delivery of the
vehicle to customer.
Work Procedure INFOID:0000000007868416

1.TRANSIT MODE CANCEL OPERATION

1. Turn ignition switch OFF.
2. Turn and hold front wiper switch to HI, and then operate turn signal switch to RH or LH.

>> GO TO 2.
2.TRANSIT MODE CANCEL CHECK
1. Turn front wiper switch and turn signal switch OFF.
2. Turn ignition switch ON.
3. Check that turn signal indicator on combination meter does not turn ON.

>> WORK END

Revision: 2011 November BCS-4 2011 G Sedan

 BODY CONTROL SYSTEM
< SYSTEM DESCRIPTION >
SYSTEM DESCRIPTION A
BODY CONTROL SYSTEM
System Description INFOID:0000000006211043
B

OUTLINE
• BCM (Body Control Module) controls the various electrical components. It inputs the information required to C
the control from CAN communication and the signal received from each switch and sensor.
• BCM has combination switch reading function for reading the operation status of combination switches (light,
turn signal, wiper and washer) in addition to a function for controlling the operation of various electrical com-
ponents. It also has the signal transmission function as the passed point of signal and the power saving con- D
trol function that reduces the power consumption with the ignition switch OFF.
• BCM is equipped with the diagnosis function that performs the diagnosis with CONSULT-III and various set-
tings. E
BCM control function list

System Refer to F
Combination switch reading system BCS-7, "System Diagram"
Signal buffer system BCS-11, "System Diagram"
G
Power consumption control system BCS-12, "System Diagram"
Auto light system EXL-11, "System Diagram"
Turn signal and hazard warning lamp system EXL-20, "System Diagram" H
Headlamp system EXL-7, "System Diagram"
Parking, license plate and tail lamps system EXL-22, "System Diagram"
I
Front fog lamp system EXL-18, "System Diagram"
Exterior lamp battery saver system EXL-24, "System Diagram"
Daytime running light system EXL-15, "System Diagram" J
Interior room lamp control system
Step lamp system INL-5, "System Diagram"
Trunk room lamp system K
Interior room lamp battery saver system INL-9, "System Diagram"
Front wiper and washer system WW-9, "WITHOUT RAIN SENSOR : System Diagram" L
Warning chime system WCS-5, "WARNING CHIME SYSTEM : System Diagram"
Door lock system DLK-11, "System Diagram"
Trunk open system DLK-47, "System Diagram" BCS
Infiniti Vehicle Immobilizer System (IVIS) - NATS SEC-17, "System Diagram"
Vehicle security system SEC-23, "System Diagram"
N
DLK-30, "REMOTE KEYLESS ENTRY FUNCTION : System De-
Panic alarm
scription"
ADP-14, "AUTOMATIC DRIVE POSITIONER SYSTEM : System
Automatic drive positioner system O
Diagram"
Rear window defogger system DEF-4, "System Diagram"
Door lock function P
Trunk open function
Remote keyless entry
Intelligent Key system/engine start system function DLK-16, "INTELLIGENT KEY SYSTEM : System Diagram"
Key reminder function
Warning function
Engine start function

Revision: 2011 November BCS-5 2011 G Sedan

 BODY CONTROL SYSTEM
< SYSTEM DESCRIPTION >
System Refer to
Power window system PWC-9, "System Diagram"
Retained accessory power (RAP) system PWC-9, "System Description"
Tire pressure monitor system (TPMS) - AIR PRESSURE MONI-
WT-8, "System Description"
TOR

Component Parts Location INFOID:0000000006211044

JPMIA0064ZZ

1. BCM
A. Dash side lower (passenger side)

Revision: 2011 November BCS-6 2011 G Sedan

 COMBINATION SWITCH READING SYSTEM
< SYSTEM DESCRIPTION >
COMBINATION SWITCH READING SYSTEM
A
System Diagram INFOID:0000000006211045

JMMIA0333GB

NOTE: G
• *1: TAIL LAMP switch links lighting switch 1ST position.
• *2: “FR WIP INT/AT” is FR WIPER INT/AUTO.
System Description INFOID:0000000006211046 H

OUTLINE
• BCM reads the status of the combination switch (light, turn signal, wiper and washer) and recognizes the I
status of each switch.
• BCM is a combination of 5 output terminals (OUTPUT 1 - 5) and 5 input terminals (INPUT 1 - 5). It reads a
maximum of 20 switch status.
J
COMBINATION SWITCH MATRIX
Combination switch circuit
K

BCS

JMMIA0334GB
P
NOTE:
• *1: TAIL LAMP switch links lighting switch 1ST position.
• *2: “FR WIP INT/AT” is FR WIPER INT/AUTO.

Revision: 2011 November BCS-7 2011 G Sedan

 COMBINATION SWITCH READING SYSTEM
< SYSTEM DESCRIPTION >
Combination switch INPUT-OUTPUT system list
System OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5
INPUT 1 — FR WASHER FR WIPER LOW TURN LH TURN RH
INPUT 2 FR WIPER HI — FR WIPER INT/AUTO PASSING HEADLAMP 1
INPUT 3 INT VOLUME 1 — — HEADLAMP 2 HI BEAM
INPUT 4 — INT VOLUME 3 AUTO LIGHT — TAIL LAMP
INPUT 5 INT VOLUME 2 — — FR FOG —
NOTE:
Headlamp has a dual system switch.

COMBINATION SWITCH READING FUNCTION

Description
• BCM reads the status of the combination switch at 10 ms interval normally.

JPMIA0067GB

NOTE:
BCM reads the status of the combination switch at 60 ms interval when BCM is controlled at low power con-
sumption mode.
• BCM operates as follows and judges the status of the combination switch.
- INPUT 1 - 5 outputs the voltage waveforms of 5 systems simultaneously.
- It operates the transistor on OUTPUT side in the following order: OUTPUT 5 → 4 → 3 → 2 → 1.
- The voltage waveform of INPUT corresponding to the formed circuit changes according to the operation of
the transistor on OUTPUT side if any (1 or more) switches are ON.
- It reads this change of the voltage as the status signal of the combination switch.

JPMIA0068GB

Revision: 2011 November BCS-8 2011 G Sedan

 COMBINATION SWITCH READING SYSTEM
< SYSTEM DESCRIPTION >
Operation Example
In the following operation example, the combination of the status signals of the combination switch is replaced A
as follows: INPUT 1 - 5 to “1 - 5” and OUTPUT 1 - 5 to “A - E”.
Example 1: When a switch (TURN RH switch) is turned ON
• The circuit between INPUT 1 and OUTPUT 5 is formed when the TURN RH switch is turned ON. B

G
JMMIA0335GB

• BCM detects the combination switch status signal “1E” when the signal of OUTPUT 5 is input to INPUT 1.
• BCM judges that the TURN RH switch is ON when the signal “1E” is detected. H
Example 2: When some switches (turn RH switch, front wiper LO switch) are turned ON
• The circuits between INPUT 1 and OUTPUT 5 and between INPUT 1 and OUTPUT 3 are formed when the
TURN RH switch and FR WIPER LOW switch are turned ON. I

BCS

N
JMMIA0336GB

• BCM detects the combination switch status signal “1CE” when the signals of OUTPUT 3 and OUTPUT 5 are
input to INPUT 1.
• BCM judges that the TURN RH switch and FR WIPER LOW switch are ON when the signal “1CE” is O
detected.
WIPER VOLUME DIAL POSITION
P
BCM judges the wiper volume dial 1 - 7 by the status of INT VOLUME 1, 2 and 3 switches.

Switch status
Wiper volume dial position
INT VOLUME 1 INT VOLUME 2 INT VOLUME 3
1 ON ON ON
2 ON ON OFF

Revision: 2011 November BCS-9 2011 G Sedan

 COMBINATION SWITCH READING SYSTEM
< SYSTEM DESCRIPTION >
Switch status
Wiper volume dial position
INT VOLUME 1 INT VOLUME 2 INT VOLUME 3
3 ON OFF OFF
4 OFF OFF OFF
5 OFF OFF ON
6 OFF ON ON
7 OFF ON OFF
NOTE:
For details of wiper volume dial position, refer to WW-9, "WITHOUT RAIN SENSOR : System Description".

Revision: 2011 November BCS-10 2011 G Sedan

 SIGNAL BUFFER SYSTEM
< SYSTEM DESCRIPTION >
SIGNAL BUFFER SYSTEM
A
System Diagram INFOID:0000000006211047

JPMIA1239GB

G
System Description INFOID:0000000006211048

OUTLINE H
BCM has the signal transmission function that outputs/transmits each input/received signal to each unit.
Signal transmission function list
I
Signal name Input Output Description
Inputs the push-button ignition
switch (push switch) signal and
J
• Ignition switch ON signal Push-button ignition switch • IPDM E/R (CAN)
transmits the ignition switch sta-
• Ignition switch signal (push switch) • Driver seat control unit (CAN)
tus judged with BCM via CAN
communication. K
• Combination meter (through
unified meter and A/C amp.) Inputs the door switch signal
Door switch signal Any door switch (CAN) and transmits it via CAN com-
• IPDM E/R (CAN) munication. L
• Driver seat control unit (CAN)
Inputs the trunk room lamp
Combination meter (through
switch signal and transmits the BCS
Trunk switch signal Trunk room lamp switch unified meter and A/C amp.)
trunk switch signal via CAN
(CAN)
communication.
Combination meter (through Transmits the received oil pres- N
Oil pressure switch signal IPDM E/R (CAN) unified meter and A/C amp.) sure switch signal via CAN
(CAN) communication.
Inputs the stop lamp switch 1
• Stop lamp switch signal and stop lamp switch 2 O
Stop lamp switch signal • ICC brake hold relay (with TCM (CAN) signal, and transmits the stop
ICC) lamp switch signal via CAN
communication.
P

Revision: 2011 November BCS-11 2011 G Sedan

 POWER CONSUMPTION CONTROL SYSTEM
< SYSTEM DESCRIPTION >
POWER CONSUMPTION CONTROL SYSTEM
System Diagram INFOID:0000000006211049

JPMIA0069GB

System Description INFOID:0000000006211050

OUTLINE
• BCM incorporates a power saving control function that reduces the power consumption according to the
vehicle status.
• BCM switches the status (control mode) by itself with the power saving control function. It performs the sleep
request to each unit [IPDM E/R, combination meter (unified meter and A/C amp.) and driver seat control unit]
that operates with the ignition switch OFF.
Normal mode (wake-up)
- CAN communication is normally performed with other units
- Each control with BCM is operating properly
CAN communication sleep mode (CAN sleep)
- CAN transmission is stopped
- Control with BCM only is operating
Low power consumption mode (BCM sleep)
- Low power consumption control is active
- CAN transmission is stopped
LOW POWER CONSUMPTION CONTROL WITH BCM
BCM reduces the power consumption with the following operation in the low power consumption mode.
• The reading interval of the each switches changes from 10 ms interval to 60 ms interval.
Sleep mode activation
• BCM receives the sleep-ready signal (ready) from IPDM E/R and unified meter and A/C amp. via CAN com-
munication.
• BCM transmits the sleep wake up signal (sleep) to each unit when all of the CAN sleep conditions are ful-
filled.
• Each unit stops the transmission of CAN communication with the sleep wake up signal. BCM is in CAN com-
munication sleep mode.
• BCM is in the low power consumption mode and perform the low power consumption control when all of the
BCM sleep conditions are fulfilled with CAN sleep condition.

Revision: 2011 November BCS-12 2011 G Sedan

 POWER CONSUMPTION CONTROL SYSTEM
< SYSTEM DESCRIPTION >
Sleep condition
CAN sleep condition BCM sleep condition A
• Receiving the sleep-ready signal (ready) from all units
• Ignition switch: OFF
• Vehicle security system and panic alarm: Not operation • Interior room lamp battery saver: Time out
B
• Warning chime: Not operation • RAP system: Not operation
• Intelligent Key system buzzer: Not operation • Power window switch communication: No transmission
• Trunk room lamp switch status: No change • Push-button ignition switch illumination: OFF
• Stop lamp switch: OFF • Infiniti Vehicle Immobilizer System (IVIS) - NATS: Not operation C
• ICC brake hold relay (with ICC): OFF • Remote keyless entry receiver communication status: No com-
• Key slot (card switch) status: No change munication
• Turn signal indicator lamp: Not operation • Tire pressure monitor system (TPMS) - AIR PRESSURE MON-
• Exterior lamp: OFF ITOR: Stop D
• Door lock status: No change • LOCK indicator lamp: OFF
• CONSULT-III communication status: Not communication • ACC indicator lamp: OFF
• Meter display signal: Non-transmission • ON indicator lamp: OFF
• Door switch status: No change E
• Rear window defogger: OFF

Wake-up operation
G
• BCM changes from the low power consumption mode to the CAN communication sleep mode when the any
of the BCM wake-up conditions is fulfilled. Only the control with BCM is activated.
• BCM transmits the sleep wake up signal (wake up) to each unit when any of the CAN wake-up conditions is
fulfilled. It changes from the low power consumption mode or the CAN communication sleep mode to the H
normal mode.
• Each unit starts the transmission of CAN communication with the sleep wake up signal. In addition, the uni-
fied meter and A/C amp. transmits the wake up signal to BCM via CAN communication to report the CAN I
communication start.
Wake-up condition
BCM wake-up condition CAN wake-up condition J
• Receiving the sleep-ready signal (Not-ready) from any units
• Key slot (key switch): OFF → ON, ON → OFF
• Push-button ignition switch (push switch): OFF→ ON
• Hazard switch: OFF → ON K
• PASSING switch: OFF → ON, ON → OFF
• TAIL LAMP switch: OFF → ON
• Driver door switch: OFF → ON, ON → OFF L
• Trunk lid opener switch: OFF → ON • Passenger door switch: OFF → ON, ON → OFF
• Power window switch communication: Receiving • Rear RH door switch: OFF → ON, ON → OFF
• Remote keyless entry receiver communication: Receiving • Rear LH door switch: OFF → ON, ON → OFF
• Trunk room lamp switch: OFF → ON, ON → OFF BCS
• Driver door request switch: OFF → ON
• Passenger door request switch: OFF → ON
• Trunk lid opener request switch: OFF → ON
• Stop lamp switch: ON N
• ICC brake hold relay (with ICC): ON
• Clutch interlock switch: OFF → ON

Revision: 2011 November BCS-13 2011 G Sedan

 POWER CONSUMPTION CONTROL SYSTEM
< SYSTEM DESCRIPTION >
Component Parts Location INFOID:0000000006211051

JPMIA0072ZZ

1. BCM 2. IPDM E/R 3. Unified meter and A/C amp.

4. Driver seat control unit
A. Dash side lower (passenger side) B. Engine room dash panel (RH) C. Behind Cluster lid C
D. Backside of the seat cushion (driver
seat)

Revision: 2011 November BCS-14 2011 G Sedan

 DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
A
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM) INFOID:0000000006211052
B
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
C
Diagnosis mode Function Description
Work Support Changes the setting for each system function.
D
Self Diagnostic Result Displays the diagnosis results judged by BCM.
Monitors the reception status of CAN communication viewed from BCM. Refer to CONSULT-III opera-
CAN Diag Support Monitor
tion manual.
E
Data Monitor The BCM input/output signals are displayed.
Active Test The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification The BCM part number is displayed. F
Configuration This function is not used even though it is displayed.

SYSTEM APPLICATION
G
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×: Applicable item H
Diagnosis mode
System Sub system selection item
Work Support Data Monitor Active Test
I
Door lock DOOR LOCK × × ×
Rear window defogger REAR DEFOGGER × ×
Warning chime BUZZER × × J
Interior room lamp timer INT LAMP × × ×
Exterior lamp HEAD LAMP × × ×
Wiper and washer WIPER × × ×
K

Turn signal and hazard warning lamps FLASHER × × ×

— AIR CONDITONER* L
• Intelligent Key system
INTELLIGENT KEY × × ×
• Engine start system
Combination switch COMB SW × BCS
Body control system BCM ×
IVIS - NATS IMMU × ×
Interior room lamp battery saver BATTERY SAVER × × × N
Trunk lid open TRUNK × ×
Vehicle security system THEFT ALM × × ×
O
RAP system RETAINED PWR ×
Signal buffer system SIGNAL BUFFER × ×
TPMS TPMS (AIR PRESSURE MONITOR) × × × P

NOTE:
*: This item is displayed, but is not used.

FREEZE FRAME DATA (FFD)

The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on
CONSULT-III.

Revision: 2011 November BCS-15 2011 G Sedan

 DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION >

CONSULT screen item Indication/Unit Description

Vehicle Speed km/h Vehicle speed of the moment a particular DTC is detected
Odo/Trip Meter km Total mileage (Odometer value) of the moment a particular DTC is detected
While turning BCM status from low power consumption mode to
SLEEP>LOCK
normal mode (Power supply position is “LOCK”)
While turning BCM status from low power consumption mode to
SLEEP>OFF
normal mode (Power supply position is “OFF”.)
LOCK>ACC While turning power supply position from “LOCK” to “ACC”
ACC>ON While turning power supply position from “ACC” to “IGN”
While turning power supply position from “RUN” to “ACC” (Vehicle
RUN>ACC
is stopping and selector lever is except P position.)
While turning power supply position from “CRANKING” to “RUN”
CRANK>RUN
(From cranking up the engine to run it)
While turning power supply position from “RUN“ to “ACC” (Emer-
RUN>URGENT
gency stop operation)
ACC>OFF While turning power supply position from “ACC” to “OFF”
OFF>LOCK While turning power supply position from “OFF” to “LOCK”
Power position status of
OFF>ACC While turning power supply position from “OFF” to “ACC”
Vehicle Condition the moment a particular
ON>CRANK DTC is detected While turning power supply position from “IGN” to “CRANKING”
While turning BCM status from normal mode (Power supply posi-
OFF>SLEEP
tion is “OFF”.) to low power consumption mode
While turning BCM status from normal mode (Power supply posi-
LOCK>SLEEP
tion is “LOCK”.) to low power consumption mode
Power supply position is “LOCK” (Ignition switch OFF with steer-
LOCK
ing is locked.)
Power supply position is “OFF” (Ignition switch OFF with steering
OFF
is unlocked.)
ACC Power supply position is “ACC” (Ignition switch ACC)
Power supply position is “IGN” (Ignition switch ON with engine
ON
stopped)
Power supply position is “RUN” (Ignition switch ON with engine
ENGINE RUN
running)
CRANKING Power supply position is “CRANKING” (At engine cranking)
The number of times that ignition switch is turned ON after DTC is detected
• The number is 0 when a malfunction is detected now.
IGN Counter 0 - 39 • The number increases like 1 → 2 → 3...38 → 39 after returning to the normal condition
whenever ignition switch OFF → ON.
• The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.

DOOR LOCK
DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK) INFOID:0000000006211053

BCM CONSULT-III FUNCTION

CONSULT-III performs the following functions via CAN communication with BCM.

Diagnosis mode Function Description

WORK SUPPORT Changes the setting for each system function.
DATA MONITOR The BCM input/output signals are displayed.
ACTIVE TEST The signals used to activate each device are forcibly supplied from BCM.

WORK SUPPORT

Revision: 2011 November BCS-16 2011 G Sedan

 DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION >

Monitor item Description A

Selective unlock function mode can be changed to operate (ON) or not operate (OFF) with this
DOOR LOCK-UNLOCK SET
mode.
Automatic door lock function mode can be selected from the following in this mode. B
AUTOMATIC DOOR LOCK SE- • VH SPD: All doors are locked when vehicle speed more than 24km/h (15MPH)
LECT • P RANGE*: All doors are locked when shifting the selector lever from P position to other than
the P position
C
Automatic door unlock function mode can be selected from the following in the mode.
• MODE 1: All doors are unlocked when the power supply position is changed from ON to OFF
• MODE 2*: All doors are unlocked when shifting the selector lever from any position other than
AUTOMATIC DOOR UNLOCK the P to P position D
SELECT • MODE 3: Driver side door is unlocked when the power supply position is changed from ON to
OFF
• MODE 4*: Driver side door is unlocked when shifting the selector lever from any position other
than the P to P position E
Automatic door lock/unlock function mode can be selected from the following in this mode.
• Off: non-operational
AUTOMATIC LOCK/UNLOCK
• Unlock Only: door unlock operation only F
SET
• Lock Only: door lock operation only
• Lock/Unlock: lock/unlock operation
*: P range interlock door lock can be selected for M/T models, but automatic door lock/unlock function does not operate.
G
DATA MONITOR

Monitor Item Contents H

REQ SW-DR Indicated [ON/OFF] condition of door request switch (driver side).
REQ SW-AS Indicated [ON/OFF] condition of door request switch (passenger side).
I
REQ SW-BD/TR Indicated [ON/OFF] condition of trunk lid opener request switch.
DOOR SW-DR Indicated [ON/OFF] condition of front door switch (driver side).
DOOR SW-AS Indicated [ON/OFF] condition of front door switch (passenger side). J
DOOR SW-RR Indicated [ON/OFF] condition of rear door switch RH.
DOOR SW-RL Indicated [ON/OFF] condition of rear door switch LH.
NOTE:
K
DOOR SW-BK
This item is displayed, but cannot be monitored.
CDL LOCK SW Indicated [ON/OFF] condition of lock signal from door lock unlock switch.
L
CDL UNLOCK SW Indicated [ON/OFF] condition of unlock signal from door lock unlock switch.
KEY CYL LK-SW Indicated [ON/OFF] condition of lock signal from door key cylinder.
KEY CYL UN-SW Indicated [ON/OFF] condition of unlock signal from door key cylinder. BCS
ACTIVE TEST

Test item Description

N

This test is able to check door lock/unlock operation.

• The all door lock actuators are locked when “ALL LCK” on CONSULT-III screen is touched.
• The all door lock actuators are unlocked when “ALL UNLK” on CONSULT-III screen is touched. O
• The door lock actuator (driver side) is unlocked when “DR UNLK” on CONSULT-III screen is
DOOR LOCK
touched.
• The door lock actuator (passenger side) is unlocked when “AS UNLK” on CONSULT- III screen
is touched. P
• The door lock actuator (other) is unlocked when “OTR ULK” on CONSULT-III screen is touched.

REAR WINDOW DEFOGGER

Revision: 2011 November BCS-17 2011 G Sedan

 DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION >
REAR WINDOW DEFOGGER : CONSULT-III Function (BCM - REAR DEFOGGER)
INFOID:0000000006211054

Data monitor

Monitor Item Description

REAR DEF SW This is displayed even when it is not equipped.
PUSH SW Indicates [ON/OFF] condition of push switch.

ACTIVE TEST

Test Item Description

This test is able to check rear window defogger operation. Rear window defogger operates when
REAR DEFOGGER
“ON” on CONSULT-III screen is touched.

BUZZER
BUZZER : CONSULT-III Function (BCM - BUZZER) INFOID:0000000006211055

CONSULT-III APPLICATION ITEMS

Test item Diagnosis mode Description

Data Monitor Displays BCM input data in real time.
BUZZER
Active Test Operation of electrical loads can be checked by sending driving signal to them.

DATA MONITOR

Display item
Description
[Unit]
VEH SPEED 1 Value of vehicle speed signal received from ABS actuator and electric unit (control unit) with CAN
[Km/h] communication line.
PUSH SW
Status of push button ignition switch judged by BCM.
[On/Off]
UNLK SEN-DR
Status of unlock sensor judged by BCM.
[On/Off]
KEY SW-SLOT
Status of key slot judged by BCM.
[On/Off]
TAIL LAMP SW
Status of each switch judged by BCM using the combination switch readout function.
[On/Off]
FR FOG SW
Status of front fog lamp switch judged by BCM.
[On/Off]
DOOR SW-DR
Status of driver side door switch judged by BCM.
[On/Off]

ACTIVE TEST

Display item
Description
[Unit]
IGN KEY WARN ALM The key warning chime operation can be checked by operating the relevant function (On/Off).
SEAT BELT WARN TEST The seat belt warning chime operation can be checked by operating the relevant function (On/Off).
ID REGIST WARNING The ID regist warning chime operation can be checked by operating the relevant function (On/Off).
LIGHT WARN ALM The light warning chime operation can be checked by operating the relevant function (On/Off).
RUN FLAT/T WARN BUZZER The run-flat tire warning chime operation can be checked by operating the relevant function (On/Off).

INT LAMP

Revision: 2011 November BCS-18 2011 G Sedan

 DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION >
INT LAMP : CONSULT-III Function (BCM - INT LAMP) INFOID:0000000006211056

A
WORK SUPPORT

JPLIA0093GB F

Service item Setting item Setting

ON* With the interior room lamp timer function G
SET I/L D-UNLCK INTCON
OFF Without the interior room lamp timer function
MODE 2 7.5 sec.
H
ROOM LAMP TIMER SET MODE 3* 15 sec. Sets the interior room lamp ON time. (Timer operating time)
MODE 4 30 sec.
MODE 1 0.5 sec. I
MODE 2* 1 sec.
ROOM LAMP ON TIME SET MODE 3 2 sec. Sets the interior room lamp gradual brightening time.
J
MODE 4 3 sec.
MODE 5 0 sec.
MODE 1 0.5 sec. K
MODE 2 1 sec.
ROOM LAMP OFF TIME SET Sets the interior room lamp gradual dimming time.
MODE 3 2 sec.
MODE 4* 3 sec. L
MODE 1* Interior room lamp timer activates with synchronizing all doors.
R LAMP TIMER LOGIC SET Interior room lamp timer activates with synchronizing the driver door
MODE 2 BCS
only.
*: Factory setting

DATA MONITOR N

Monitor item
Description
[Unit]
O
REQ SW-DR
The switch status input from request switch (driver side)
[On/Off]
REQ SW-AS P
The switch status input from request switch (passenger side)
[On/Off]
PUSH SW
The switch status input from push-button ignition switch
[On/Off]
ACC RLY-F/B NOTE:
[On/Off] The item is indicated, but not monitored.
KEY SW-SLOT
Key switch status input from key slot
[On/Off]

Revision: 2011 November BCS-19 2011 G Sedan

 DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION >
Monitor item
Description
[Unit]
DOOR SW-DR
The switch status input from front door switch (driver side)
[On/Off]
DOOR SW-AS
The switch status input from front door switch (passenger side)
[On/Off]
DOOR SW-RR
The switch status input from rear door switch RH
[On/Off]
DOOR SW- RL
The switch status input from rear door switch LH
[On/Off]
DOOR SW-BK NOTE:
[On/Off] The item is indicated, but not monitored.
CDL LOCK SW Lock switch status received from door lock/unlock switch by power window switch se-
[On/Off] rial link
CDL UNLOCK SW Unlock switch status received from door lock/unlock switch by power window switch
[On/Off] serial link
KEY CYL LK-SW Lock switch status received from key cylinder switch by power window switch serial
[On/Off] link
KEY CYL UN-SW Unlock switch status received from key cylinder switch by power window switch serial
[On/Off] link
TRNK/HAT MNTR
The switch status input from trunk room lamp switch
[On/Off]
RKE-LOCK
Lock signal status received from remote keyless entry receiver
[On/Off]
RKE-UNLOCK
Unlock signal status received from remote keyless entry receiver
[On/Off]

ACTIVE TEST

Test item Operation Description

Outputs the interior room lamp control signal to turn map lamp and personal lamp ON
On
INT LAMP (Map lamp switch is in DOOR position).
Off Stops the interior room lamp control signal to turn map lamp and personal lamp OFF.
On Outputs the step lamp control signal to turn step lamp ON.
STEP LAMP TEST
Off Stops the step lamp control signal to turn step lamp OFF.
On Outputs the trunk room lamp control signal to turn trunk room lamp ON.
LUGGAGE LAMP TEST
Off Stops the trunk room lamp control signal to turn trunk room lamp OFF.

HEADLAMP
HEADLAMP : CONSULT-III Function (BCM - HEAD LAMP) INFOID:0000000006211057

WORK SUPPORT

Service item Setting item Setting

On* With the exterior lamp battery saver function
BATTERY SAVER SET
Off Without the exterior lamp battery saver function

Revision: 2011 November BCS-20 2011 G Sedan

 DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION >
Service item Setting item Setting
A
MODE 1* 45 sec.
Without the func-
MODE 2
tion
B
MODE 3 30 sec.
MODE 4 60 sec. Sets delay timer function timer operation time.
ILL DELAY SET
(All doors closed)
MODE 5 90 sec. C
MODE 6 120 sec.
MODE 7 150 sec.
D
MODE 8 180 sec.
MODE 1* Normal

CUSTOM A/LIGHT SET- MODE 2 More sensitive setting than normal setting (Turns ON earlier than normal operation.) E
TING MODE 3 More sensitive setting than MODE 2 (Turns ON earlier than MODE 2.)
MODE 4 Less sensitive setting than normal setting (Turns ON later than normal operation.)
*: Factory setting F

DATA MONITOR
G
Monitor item
Description
[Unit]
PUSH SW
The switch status input from push-button ignition switch H
[On/Off]
ENGINE STATE
The engine status received from ECM with CAN communication
[Stop/Stall/Crank/Run]
I
VEH SPEED 1 The value of the vehicle speed received from unified meter and A/C amp. with CAN
[km/h] communication
KEY SW-SLOT
Key switch status input from key slot J
[On/Off]
TURN SIGNAL R
[On/Off]
K
TURN SIGNAL L
[On/Off]
TAIL LAMP SW
[On/Off] L
HI BEAM SW
[On/Off]
HEAD LAMP SW1 BCS
Each switch status that BCM judges from the combination switch reading function
[On/Off]
HEAD LAMP SW2
[On/Off] N
PASSING SW
[On/Off]
AUTO LIGHT SW O
[On/Off]
FR FOG SW
[On/Off] P
RR FOG SW NOTE:
[On/Off] The item is indicated, but not monitored.
DOOR SW-DR
The switch status input from driver side door switch
[On/Off]
DOOR SW-AS
The switch status input from passenger side door switch
[On/Off]

Revision: 2011 November BCS-21 2011 G Sedan

 DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION >
Monitor item
Description
[Unit]
DOOR SW-RR
The switch status input from rear door switch RH
[On/Off]
DOOR SW- RL
The switch status input from rear door switch LH
[On/Off]
DOOR SW-BK NOTE:
[On/Off] The item is indicated, but not monitored.
OPTICAL SENSOR
The value of exterior brightness voltage input from the optical sensor
[V]

ACTIVE TEST

Test item Operation Description

Transmits the position light request signal to IPDM E/R with CAN com-
On
TAIL LAMP munication to turn the tail lamp ON.
Off Stops the position light request signal transmission.
Transmits the high beam request signal with CAN communication to turn
Hi
the headlamp (HI).
HEAD LAMP Transmits the low beam request signal with CAN communication to turn
Low
the headlamp (LO).
Off Stops the high & low beam request signal transmission.
Transmits the front fog light request signal to IPDM E/R with CAN com-
On
FR FOG LAMP munication to turn the front fog lamp ON.
Off Stops the front fog light request signal transmission.
On NOTE:
RR FOG LAMP
Off The item is indicated, but cannot be tested.

On NOTE:
DAYTIME RUNNING LIGHT
Off The item is indicated, but cannot be tested.

RH
NOTE:
CORNERING LAMP LH
The item is indicated, but cannot be tested.
Off
On NOTE:
ILL DIM SIGNAL
Off The item is indicated, but cannot be tested.

WIPER
WIPER : CONSULT-III Function (BCM - WIPER) INFOID:0000000006211058

WORK SUPPORT

Service item Setting item Description

Linked with vehicle speed
On
WIPER SPEED (Front wiper intermittent time linked with the vehicle speed and wiper intermittent dial position)
SETTING*1 Not linked with vehicle speed
Off*2 (Front wiper intermittent time linked with the wiper intermittent dial position)
*1:Without rain sensor
*2:Initial setting

DATA MONITOR

Revision: 2011 November BCS-22 2011 G Sedan

 DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION >

Monitor Item A
Description
[Unit]
VEH SPEED 1 Displays the value of the vehicle speed signal received from unified meter and A/C amp. with
[km/h] CAN communication.
B
PUSH SW
The switch status input from push-button ignition switch.
[Off/On]
FR WIPER HI C
[Off/On]
FR WIPER LOW
[Off/On]
Status of each switch judged by BCM using the combination switch reading function D
FR WASHER SW
[Off/On]
FR WIPER INT
E
[Off/On]
FR WIPER STOP Displays the status of the front wiper stop position signal received from IPDM E/R with CAN
[Off/On] communication.
F
INT VOLUME
Status of each switch judged by BCM using the combination switch reading function
[1 − 7]

ACTIVE TEST G

Test item Operation Description

Transmits the front wiper request signal (HI) to IPDM E/R with CAN communication to H
Hi
operate the front wiper HI operation.
Transmits the front wiper request signal (LO) to IPDM E/R with CAN communication to
Lo
FRONT WIPER operate the front wiper LO operation. I
Transmits the front wiper request signal (INT) to IPDM E/R with CAN communication to
INT
operate the front wiper INT operation.
Off Stops transmitting the front wiper request signal to stop the front wiper operation. J
FLASHER
FLASHER : CONSULT-III Function (BCM - FLASHER) INFOID:0000000006211059 K

WORK SUPPORT
L
Service item Setting item Setting
Lock Only* With locking only
Sets the hazard warning lamp answer back function BCS
HAZARD ANSWER Unlk Only With unlocking only
when the door is lock/unlock with the request switch or
BACK Lock/Unlk With locking/unlocking the key fob.
Off Without the function N
*: Factory setting

DATA MONITOR
O
Monitor item
Description
[Unit]
REQ SW-DR P
The switch status input from the request switch (driver side)
[On/Off]
REQ SW-AS
The switch status input from the request switch (passenger side)
[On/Off]
PUSH SW
The switch status input from the push-button ignition switch
[On/Off]

Revision: 2011 November BCS-23 2011 G Sedan

 DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION >
Monitor item
Description
[Unit]
TURN SIGNAL R
[On/Off]
Each switch condition that BCM judges from the combination switch reading function
TURN SIGNAL L
[On/Off]
HAZARD SW
The switch status input from the hazard switch
[On/Off]
RKE-LOCK
Lock signal status received from the remote keyless entry receiver
[On/Off]
RKE-UNLOCK
Unlock signal status received from the remote keyless entry receiver
[On/Off]
RKE-PANIC
Panic alarm signal status received from the remote keyless entry receiver
[On/Off]

ACTIVE TEST

Test item Operation Description

RH Outputs the voltage to blink the right side turn signal lamps.
FLASHER LH Outputs the voltage to blink the left side turn signal lamps.
Off Stops the voltage to turn the turn signal lamps OFF.

INTELLIGENT KEY
INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY) INFOID:0000000006211060

WORK SUPPORT

Monitor item Description

CONFIRM KEY FOB ID It can be checked whether Intelligent Key ID code is registered or not in this mode.
Auto door lock time can be changed in this mode.
• MODE 1: 1 minute
AUTO LOCK SET • MODE 2: 5 minutes
• MODE 3: 30 seconds
• MODE 4: 2 minutes
Door lock/unlock function by door request switch (driver side and passenger side) mode can
LOCK/UNLOCK BY I-KEY
be changed to operate (ON) or not operate (OFF) in this mode.
Engine start function mode can be changed to operate (ON) or not operate (OFF) with this
ENGINE START BY I-KEY
mode.
Buzzer reminder function mode by trunk opener request switch can be changed to operate
TRUNK/GLASS HATCH OPEN
(ON) or not operate (OFF) with this mode.
Panic alarm button pressing time on Intelligent Key remote control button can be selected from
the following with this mode.
PANIC ALARM SET • MODE 1: 0.5 sec.
• MODE 2: Non-operation
• MODE 3: 1.5 sec.
Unlock button pressing time on Intelligent Key button can be selected from the following with
this mode.
PW DOWN SET • MODE 1: 3 sec.
• MODE 2: Non-operation
• MODE 3: 5 sec.
Trunk button pressing on Intelligent Key button can be selected as per the following in this
mode.
TRUNK OPEN DELAY • MODE 1: Press and hold
• MODE 2: Press twice
• MODE 3: Press and hold, or press twice

Revision: 2011 November BCS-24 2011 G Sedan

 DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION >
Monitor item Description
A
Intelligent Key low battery warning mode can be changed to operate (ON) or not operate
LO- BATT OF KEY FOB WARN
(OFF) with this mode.
Key reminder function mode can be changed to operate (ON) or not operate (OFF) with this
ANTI KEY LOCK IN FUNCTI B
mode.
Hazard reminder function mode can be selected from the following with this mode.
• LOCK ONLY: Door lock operation only
HAZARD ANSWER BACK • UNLOCK ONLY: Door unlock operation only C
• LOCK/UNLOCK: Lock/unlock operation
• OFF: Non-operation
Buzzer reminder function (lock operation) mode by door request switch (driver side and pas- D
senger side) can be selected from the following with this mode.
ANS BACK I-KEY LOCK • Horn chirp: Sound horn
• Buzzer: Sound Intelligent Key warning buzzer
• OFF: Non-operation E
Buzzer reminder function (unlock operation) mode by door request switch can be changed to
ANS BACK I-KEY UNLOCK
operate (ON) or not operate (OFF) with this mode.
Starter motor can operate during the times below. F
• 70 msec
SHORT CRANKING OUTPUT
• 100 msec
• 200 msec
G
INSIDE ANT DIAGNOSIS This function allows inside key antenna self-diagnosis.
Horn reminder function mode by Intelligent Key button can be changed to operate (ON) or not
HORN WITH KEYLESS LOCK
operate (OFF) with this mode.
H
SELF-DIAG RESULT
Refer to BCS-76, "DTC Index".
I
DATA MONITOR

Monitor Item Condition

J
REQ SW -DR Indicates [ON/OFF] condition of door request switch (driver side).
REQ SW -AS Indicates [ON/OFF] condition of door request switch (passenger side).
REQ SW -BD/TR Indicates [ON/OFF] condition of trunk opener request switch. K
PUSH SW Indicates [ON/OFF] condition of push-button ignition switch.
IGN RLY2 -F/B Indicates [ON/OFF] condition of ignition relay 2.
L
NOTE:
ACC RLY-FB
This item is displayed, but cannot be monitored.

CLUTCH SW*1 Indicates [ON/OFF] condition of clutch switch.

BCS
BRAKE SW 1 Indicates [ON/OFF]*2 condition of brake switch power supply.
BRAKE SW 2 Indicates [ON/OFF] condition of brake switch.
DETE/CANCL SW Indicates [ON/OFF] condition of P position. N
SFT PN/N SW Indicates [ON/OFF] condition of P or N position.
S/L -LOCK Indicates [ON/OFF] condition of steering lock unit (LOCK).
O
S/L -UNLOCK Indicates [ON/OFF] condition of steering lock unit (UNLOCK).
S/L RELAY -F/B Indicates [ON/OFF] condition of steering lock relay.
UNLK SEN -DR Indicates [ON/OFF] condition of driver door UNLOCK status. P
PUSH SW -IPDM Indicates [ON/OFF] condition of push-button ignition switch.
IGN RLY1 -F/B Indicates [ON/OFF] condition of ignition relay 1.
DETE SW -IPDM Indicates [ON/OFF] condition of P position.
SFT PN -IPDM Indicates [ON/OFF] condition of P or N position.
SFT P -MET Indicates [ON/OFF] condition of P position.

Revision: 2011 November BCS-25 2011 G Sedan

 DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION >
Monitor Item Condition
SFT N -MET Indicates [ON/OFF] condition of N position.
ENGINE STATE Indicates [STOP/STALL/CRANK/RUN] condition of engine states.
S/L LOCK-IPDM Indicates [ON/OFF] condition of steering lock unit (LOCK).
S/L UNLK-IPDM Indicates [ON/OFF] condition of steering lock unit (UNLOCK).
S/L RELAY-REQ Indicates [ON/OFF] condition of steering lock relay.
VEH SPEED 1 Display the vehicle speed signal received from combination meter by numerical value [Km/h].
VEH SPEED 2 Display the vehicle speed signal received from ABS or VDC or TCM by numerical value [Km/h].
DOOR STAT-DR Indicates [LOCK/READY/UNLOCK] condition of driver side door status.
DOOR STAT-AS Indicates [LOCK/READY/UNLOCK] condition of passenger side door status.
ID OK FLAG Indicates [SET/RESET] condition of key ID.
PRMT ENG STRT Indicates [SET/RESET] condition of engine start possibility.
NOTE:
PRMT RKE STRT
This item is displayed, but cannot be monitored.
KEY SW -SLOT Indicates [ON/OFF] condition of key slot.
TRNK/HAT MNTR Indicates [ON/OFF] condition of trunk lid.
RKE-LOCK Indicates [ON/OFF] condition of LOCK signal from Intelligent Key.
RKE-UNLOCK Indicates [ON/OFF] condition of UNLOCK signal from Intelligent Key.
RKE-TR/BD Indicates [ON/OFF] condition of TRUNK OPEN signal from Intelligent Key.
RKE-PANIC Indicates [ON/OFF] condition of PANIC button of Intelligent Key.
RKE-P/W OPEN Indicates [ON/OFF] condition of P/W DOWN signal from Intelligent Key.
RKE-MODE CHG Indicates [ON/OFF] condition of MODE CHANGE signal from Intelligent Key.
When remote keyless entry receiver receives the signal transmitted while operating on Intelli-
RKE OPE COUN1
gent Key, the numerical value start changing.
NOTE:
RKE OPE COUN2
This item is displayed, but cannot be monitored.

*1: It is displayed but does not operate on M/T models.

*2: OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.

ACTIVE TEST

Test item Description

This test is able to check interior room lamp operation.
BATTERY SAVER
The interior room lamp is activated after “ON” on CONSULT-III screen is touched.
This test is able to check power window down operation.
PW REMOTO DOWN SET
The power window down is activated after “ON” on CONSULT-III screen is touched.
This test is able to check Intelligent Key warning buzzer operation.
OUTSIDE BUZZER
The Intelligent Key warning buzzer is activated after “ON” on CONSULT-III screen is touched.
This test is able to check warning chime in combination meter operation.
• Take away warning chime sounds when “TAKE OUT” on CONSULT-III screen is touched.
INSIDE BUZZER
• Key warning chime sounds when “KEY” on CONSULT-III screen is touched.
• OFF position warning chime sounds when “KNOB” on CONSULT-III screen is touched.
This test is able to check warning lamp operation.
INDICATOR • “KEY” Warning lamp illuminates when “KEY ON” on CONSULT-III screen is touched.
• “KEY” Warning lamp blinks when “KEY IND” on CONSULT-III screen is touched.
This test is able to check interior room lamp operation.
INT LAMP
The interior room lamp is activated after “ON” on CONSULT-III screen is touched.

Revision: 2011 November BCS-26 2011 G Sedan

 DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION >
Test item Description
A
This test is able to check meter display information
• Engine start information displays when “BP N” on CONSULT-III screen is touched.
• Engine start information displays when “BP I” on CONSULT-III screen is touched.
• Key ID warning displays when “ID NG” on CONSULT-III screen is touched. B
• Steering lock information displays when “ROTAT” on CONSULT-III screen is touched.
• P position warning displays when “SFT P” on CONSULT-III screen is touched.
LCD • Intelligent Key insert information displays when “INSRT” on CONSULT-III screen is touched.
• Intelligent Key low battery warning displays when “BATT” on CONSULT-III screen is C
touched.
• Take away through window warning displays when “NO KY” on CONSULT-III screen is
touched.
• Take away warning display when “OUTKEY” on CONSULT-III screen is touched. D
• OFF position warning display when “LK WN” on CONSULT-III screen is touched.
This test is able to check trunk lid opener actuator open operation.
TRUNK/GLASS HATCH
This actuator opens when “OPEN” on CONSULT-III screen is touched. E
This test is able to check security hazard lamp operation.
FLASHER
The hazard lamps are activated after “LH/RH/OFF” on CONSULT-III screen is touched.

HORN
This test is able to check horn operation. F
The horn is activated after “ON” on CONSULT-III screen is touched.
This test is able to check A/T shift selector power supply
P RANGE
A/T shift selector power is supplied when “ON” on CONSULT-III screen is touched. G
This test is able to check push-ignition switch illumination operation.
ENGINE SW ILLUMI
Push-ignition switch illumination illuminates when “ON” on CONSULT-III screen is touched.
This test is able to check LOCK indicator in push-ignition switch operation. H
LOCK INDICATOR LOCK indicator in push-ignition switch illuminates when “ON” on CONSULT-III screen is
touched.
This test is able to check ACC indicator in push-ignition switch operation.
I
ACC INDICATOR ACC indicator in push-ignition switch illuminates when “ON” on CONSULT-III screen is
touched.
This test is able to check on indicator in push-ignition switch operation.
IGNITION ON IND J
ON indicator in push-ignition switch illuminates when “ON” on CONSULT-III screen is touched.
This test is able to check key slot illumination operation.
KEY SLOT ILLUMI
Key slot illumination blinks when “ON” on CONSULT-III screen is touched.
This test is able to check trunk lid opener actuator open operation.
K
TRUNK/BACK DOOR
This actuator opens when “OPEN” on CONSULT-III screen is touched.

COMB SW L
COMB SW : CONSULT-III Function (BCM - COMB SW) INFOID:0000000006211061

DATA MONITOR BCS

Monitor item [UNIT] Description

FR WIPER HI Displays the status of the FR WIPER HI switch in combination switch judged by BCM with the combination
N
[Off/On] switch reading function.
FR WIPER LOW Displays the status of the FR WIPER LOW switch in combination switch judged by BCM with the combination
[Off/On] switch reading function. O
FR WASHER SW Displays the status of the FR WASHER switch in combination switch judged by BCM with the combination
[Off/On] switch reading function.
FR WIPER INT Displays the status of the FR WIPER INT/AUTO switch in combination switch judged by BCM with the com- P
[Off/On] bination switch reading function.
FR WIPER STOP
Displays the status of the front wiper stop position signal received from IPDM E/R via CAN communication.
[Off/On]
INT VOLUME
Displays the status of wiper volume dial position judged by BCM with the combination switch reading function.
[1 - 7]

Revision: 2011 November BCS-27 2011 G Sedan

 DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION >
Monitor item [UNIT] Description
TURN SIGNAL R Displays the status of the TURN RH switch in combination switch judged by BCM with the combination switch
[Off/On] reading function.
TURN SIGNAL L Displays the status of the TURN LH switch in combination switch judged by BCM with the combination switch
[Off/On] reading function.
TAIL LAMP SW Displays the status of the TAIL LAMP switch in combination switch judged by BCM with the combination
[Off/On] switch reading function.
HI BEAM SW Displays the status of the HI BEAM switch in combination switch judged by BCM with the combination switch
[Off/On] reading function.
HEAD LAMP SW 1 Displays the status of the HEADLAMP 1 switch in combination switch judged by BCM with the combination
[Off/On] switch reading function.
HEAD LAMP SW 2 Displays the status of the HEADLAMP 2 switch in combination switch judged by BCM with the combination
[Off/On] switch reading function.
PASSING SW Displays the status of the PASSING switch in combination switch judged by BCM with the combination switch
[Off/On] reading function.
AUTO LIGHT SW Displays the status of the AUTO LIGHT switch in combination switch judged by BCM with the combination
[Off/On] switch reading function.
FR FOG SW Displays the status of the FR FOG switch in combination switch judged by BCM with the combination switch
[Off/On] reading function.
RR FOG SW NOTE:
[Off/On] The item is indicated, but not monitored.

BCM
BCM : CONSULT-III Function (BCM - BCM) INFOID:0000000006211062

WORK SUPPORT

Item Description
RESET SETTING VALUE Return a value set with Work Support of each system to a default value in factory shipment.

IMMU
IMMU : CONSULT-III Function (BCM - IMMU) INFOID:0000000006859197

DATA MONITOR

Monitor item Content

CONFRM ID ALL
CONFIRM ID4
Indicates [YET] at all time.
CONFIRM ID3
Switch to [DONE] when a registered Intelligent Key is inserted into the key slot.
CONFIRM ID2
CONFIRM ID1
TP 4
TP 3
Indicates the number of ID which has been registered.
TP 2
TP 1
PUSH SW Indicates [ON/OFF] condition of push-button ignition switch.
KEY SW -SLOT Indicates [ON/OFF] condition of key slot.

ACTIVE TEST

Revision: 2011 November BCS-28 2011 G Sedan

 DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION >

Test item Description A

This test is able to check security indicator lamp operation.
THEFT IND
The lamp will be turned on when “ON” on CONSULT-III screen touched.

BATTERY SAVER B

BATTERY SAVER : CONSULT-III Function (BCM - BATTERY SAVER) INFOID:0000000006859201

C
WORK SUPPORT

Service item Setting item Setting D

On* With the exterior lamp battery saver function
BATTERY SAVER SET
Off Without the exterior lamp battery saver function
E
On* With the interior room lamp battery saver function
ROOM LAMP BAT SAV SET
Off Without the interior room lamp battery saver function
MODE 1 30 min. F
Sets the interior room lamp battery saver timer operating
ROOM LAMP TIMER SET MODE 2 60 min.
time.
MODE 3* 15 min.
*: Factory setting G

DATA MONITOR
H
Monitor item
Description
[Unit]
REQ SW-DR
[On/Off]
The switch status input from request switch (driver side) I

REQ SW-AS
The switch status input from request switch (passenger side)
[On/Off]
J
REQ SW-RR
[On/Off] NOTE:
REQ SW-RL The item is indicated, but not monitored.
[On/Off] K
PUSH SW
The switch status input from push-button ignition switch
[On/Off]
L
ACC RLY-F/B NOTE:
[On/Off] The item is indicated, but not monitored.
KEY SW-SLOT
Key switch status input from key slot BCS
[On/Off]
UNLK SEN-DR
Driver door unlock status input from unlock sensor
[On/Off]
DOOR SW-DR N
The switch status input from front door switch (driver side)
[On/Off]
DOOR SW-AS
The switch status input from front door switch (passenger side)
[On/Off] O
DOOR SW-RR
The switch status input from rear door switch RH
[On/Off]
DOOR SW- RL P
The switch status input from rear door switch LH
[On/Off]
DOOR SW-BK NOTE:
[On/Off] The item is indicated, but not monitored.
CDL LOCK SW Lock switch status received from door lock/unlock switch by power window switch se-
[On/Off] rial link

Revision: 2011 November BCS-29 2011 G Sedan

 DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION >
Monitor item
Description
[Unit]
CDL UNLOCK SW Unlock switch status received from door lock/unlock switch by power window switch
[On/Off] serial link
KEY CYL LK-SW Lock switch status received from key cylinder switch by power window switch serial
[On/Off] link
KEY CYL UN-SW Unlock switch status received from key cylinder switch by power window switch serial
[On/Off] link
TRNK/HAT MNTR
The switch status input from trunk room lamp switch
[On/Off]
RKE-LOCK
Lock signal status received from remote keyless entry receiver
[On/Off]
RKE-UNLOCK
Unlock signal status received from remote keyless entry receiver
[On/Off]

ACTIVE TEST

Test item Operation Description

Off Cuts the interior room lamp power supply to turn interior room lamp OFF.
BATTERY SAVER
On Outputs the interior room lamp power supply to turn interior room lamp ON.*
*: Each lamp switch is in ON position.
TRUNK
TRUNK : CONSULT-III Function (BCM - TRUNK) INFOID:0000000006211065

BCM CONSULT-III FUNCTION

CONSULT-III performs the following functions via CAN communication with BCM.

Diagnosis mode Function Description

DATA MONITOR The BCM input/output signals are displayed.

DATA MONITOR

Monitor Item Contents

PUSH SW Indicates [ON/OFF] condition of push switch.
UNLK SEN -DR Indicates [ON/OFF] condition of unlock sensor.
VEH SPEED 1 Indicates [Km/h] condition of vehicle speed signal from combination meter.
NOTE:
KEY CYL SW-TR
This item is displayed, but cannot be monitored.
TR CANCEL SW Indicates [ON/OFF] condition of trunk lid opener cancel switch.
TR/BD OPEN SW Indicates [ON/OFF] condition of trunk lid opener switch.
TRNK/HAT MNTR Indicates [ON/OFF] condition of trunk room lamp switch.
RKE-TR/BD Indicates [ON/OFF] condition of trunk open signal from Intelligent Key remote controller button.
TRUNK/GLASS HATCH This test is able to check trunk lid opener actuator open operation.

ACTIVE TEST

Test item Description

This test is able to check trunk lid opener actuator open operation.
TRUNK/GLASS HATCH
This actuator opens when “OPEN” on CONSULT-III screen is touched.

THEFT ALM

Revision: 2011 November BCS-30 2011 G Sedan

 DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION >
THEFT ALM : CONSULT-III Function (BCM - THEFT) INFOID:0000000006859198

A
DATA MONITOR

Monitored Item Description B

REQ SW-DR Indicates [ON/OFF] condition of door request switch (driver side).
REQ SW-AS Indicates [ON/OFF] condition of door request switch (passenger side).
C
REQ SW-BD/TR Indicates [ON/OFF] condition of trunk opener request switch.
PUSH SW Indicates [ON/OFF] condition of push-button ignition switch
UNLK SEN-DR Indicates [ON/OFF] condition of driver door UNLOCK status. D
KEY SW -SLOT Indicates [ON/OFF] condition of key slot.
DOOR SW-DR Indicates [ON/OFF] condition of front door switch LH.
E
DOOR SW-AS Indicates [ON/OFF] condition of front door switch RH.
DOOR SW-RR Indicates [ON/OFF] condition of rear door switch RH.
DOOR SW-RL Indicates [ON/OFF] condition of rear door switch LH. F
DOOR SW-BK This is displayed even when it is not equipped.
CDL LOCK SW Indicates [ON/OFF] condition of lock signal from door lock/unlock switch LH and RH.
CDL UNLOCK SW Indicates [ON/OFF] condition of unlock signal from door lock/unlock switch LH and RH. G
KEY CYL LK-SW Indicates [ON/OFF] condition of lock signal from front door key cylinder switch.
KEY CYL UN-SW Indicates [ON/OFF] condition of unlock signal from front door key cylinder switch. H
KEY CYL SW-TR This is displayed even when it is not equipped.
TR/BD OPEN SW Indicates [ON/OFF] condition of trunk lid opener switch.
TRNK/HAT MNTR Indicates [ON/OFF] condition of trunk room lamp switch. I
RKE-LOCK Indicates [ON/OFF] condition of LOCK signal from Intelligent Key.
RKE-UNLOCK Indicates [ON/OFF] condition of UNLOCK signal from Intelligent Key.
J
RKE-TR/BD Indicates [ON/OFF] condition of TRUNK OPEN signal from Intelligent Key.

WORK SUPPORT
K
Test Item Description
SECURITY ALARM SET This mode is able to confirm and change security alarm ON-OFF setting.
L
The switch which triggered vehicle security alarm is recorded. This mode is able to confirm and
THEFT ALM TRG erase the record of vehicle security alarm. The trigger data can be erased by touching “CLEAR” on
CONSULT-III screen.
BCS
ACTIVE TEST

Test Item Description

N
This test is able to check security indicator lamp operation. The lamp will be turned on when “ON”
THEFT IND
on CONSULT-III screen is touched.
This test is able to check vehicle security horn operation. The horns will be activated for 0.5 sec-
VEHICLE SECURITY HORN O
onds after “ON” on CONSULT-III screen is touched.
This test is able to check vehicle security lamp operation. The headlamps will be activated for 0.5
HEADLAMP(HI)
seconds after “ON” on CONSULT-III screen is touched.
P
This test is able to check vehicle security hazard lamp operation. The hazard lamps will be activat-
FLASHER
ed after “ON” on CONSULT-III screen is touched.

RETAIND PWR
RETAIND PWR : CONSULT-III Function (BCM - RETAINED PWR) INFOID:0000000006211067

Data monitor

Revision: 2011 November BCS-31 2011 G Sedan

 DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION >

Monitor Item Description

DOOR SW-DR Indicates [ON/OFF] condition of driver side door switch.
DOOR SW-AS Indicates [ON/OFF] condition of passenger side door switch.

SIGNAL BUFFER
SIGNAL BUFFER : CONSULT-III Function (BCM - SIGNAL BUFFER) INFOID:0000000006211068

DATA MONITOR

Monitor item [UNIT] Description

PUSH SW
Displays the status of the push-button ignition switch (push switch) judged by BCM.
[Off/On]

ACTIVE TEST

Opera-
Test item Description
tion
Off OFF
OIL PRESSURE SW BCM transmits the oil pressure switch signal to the unified meter and A/C amp. via CAN com-
On
munication, which illuminates the oil pressure warning lamp in the combination meter.

AIR PRESSURE MONITOR

AIR PRESSURE MONITOR : CONSULT-III Function (BCM - AIR PRESSURE MONI-
TOR) INFOID:0000000006211069

WORK SUPPORT MODE

ID Read
The registered ID number is displayed.
ID Regist
Refer to WT-22, "Work Procedure".
SELF-DIAG RESULTS MODE
Operation Procedure
Refer to BCS-76, "DTC Index".
DATA MONITOR MODE
Screen of data monitor mode is displayed.
NOTE:
When malfunction is detected, CONSULT-III perform REAL-TIME DIAGNOSIS.
Also, any malfunction detected while in this mode will be displayed at real time.

Monitor item (Unit) Remark

AIR PRESS FL (kPa//kg/cm2/Psi)

AIR PRESS FR (kPa//kg/cm2/Psi)

Tire pressure
AIR PRESS RR (kPa//kg/cm2/Psi)

AIR PRESS RL (kPa//kg/cm2/Psi)

ID REGST FL1 (Green/Red)
ID REGST FR1 (Green/Red)
Registration ID
ID REGST RR1 (Green/Red)
ID REGST RL1 (Green/Red)

Revision: 2011 November BCS-32 2011 G Sedan

 DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION >
Monitor item (Unit) Remark
A
WARNING LAMP (On/Off) Low tire pressure warning lamp
BUZZER (On/Off) Buzzer in combination meter
NOTE: B
Before performing the self-diagnosis, be sure to register the ID, or erase the actual malfunction location may
be different from that displayed on CONSULT-III.
ACTIVE TEST MODE C
NOTE:
Before performing the self-diagnosis, be sure to register the ID, or erase the actual malfunction may be differ-
ent from that displayed on CONSULT-III. D
TEST ITEM LIST

Test item Content E

WARNING LAMP This test is able to check to check that the low tire pressure warning lamp turns on.
This test is able to check to check that the buzzer sounds or the low tire pressure warning lamp
ID REGIST WARNING
turns on. F
FLASHER This test is able to check to check that each turn signal lamp turns on.
HORN This test is able to check to check that the horn sounds.
G

BCS

Revision: 2011 November BCS-33 2011 G Sedan

 U1000 CAN COMM
< DTC/CIRCUIT DIAGNOSIS >
DTC/CIRCUIT DIAGNOSIS
U1000 CAN COMM
Description INFOID:0000000006211070

CAN (Controller Area Network) is a serial communication line for real time applications. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Modern
vehicle is equipped with many electronic control unit, and each control unit shares information and links with
other control units during operation (not independent). In CAN communication, control units are connected
with 2 communication lines (CAN H-line, CAN L-line) allowing a high rate of information transmission with less
wiring. Each control unit transmits/receives data but selectively reads required data only.
CAN Communication Signal Chart. Refer to LAN-26, "CAN Communication Signal Chart".
DTC Logic INFOID:0000000006211071

DTC DETECTION LOGIC

CONSULT-III display
DTC DTC Detection Condition Possible cause
description
When BCM cannot communicate CAN com-
U1000 CAN COMM munication signal continuously for 2 seconds CAN communication system
or more.

Diagnosis Procedure INFOID:0000000006211072

1.PERFORM SELF DIAGNOSTIC

1. Turn ignition switch ON and wait for 2 seconds or more.
2. Check “Self Diagnostic Result”.
Is DTC “U1000” displayed?
YES >> Refer to LAN-17, "Trouble Diagnosis Flow Chart".
NO >> Refer to GI-43, "Intermittent Incident".

Revision: 2011 November BCS-34 2011 G Sedan

 U1010 CONTROL UNIT (CAN)
< DTC/CIRCUIT DIAGNOSIS >
U1010 CONTROL UNIT (CAN)
A
DTC Logic INFOID:0000000006211073

DTC DETECTION LOGIC B

CONSULT-III display de-

DTC DTC Detection Condition Possible cause
scription C
U1010 CONTROL UNIT(CAN) BCM detected internal CAN communication circuit malfunction. BCM

Diagnosis Procedure INFOID:0000000006211074

D
1.REPLACE BCM
When DTC “U1010” is detected, replace BCM. E

>> Replace BCM. Refer to BCS-82, "Exploded View".

F

BCS

Revision: 2011 November BCS-35 2011 G Sedan

 U0415 VEHICLE SPEED
< DTC/CIRCUIT DIAGNOSIS >
U0415 VEHICLE SPEED
Description INFOID:0000000006211075

U0415 is displayed if any unusual condition is present in the reception status of the vehicle speed signal from
the ABS actuator and electric unit (control unit).
DTC Logic INFOID:0000000006211076

DTC DETECTION LOGIC

CONSULT-III display
DTC DTC Detection Condition Probable cause
description
When the vehicle speed signal received from
• ABS actuator and electric unit (control unit)
U0415 VEHICLE SPEED the ABS actuator and electric unit (control
• BCM
unit) remains abnormal for 2 seconds or more.

DTC CONFIRMATION PROCEDURE

1.DTC CONFIRMATION
1. Erase the DTC.
2. Turn ignition switch OFF.
3. Perform the “Self Diagnostic Result” of CONSULT-III, when passed 2 seconds or more after the ignition
switch is turned ON.
Is any DTC detected?
YES >> Refer to BCS-36, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis Procedure INFOID:0000000006211077

1.ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAG RESULTS

Perform “Self-Diagnostic Result” of ABS actuator and electric unit (control unit) with CONSULT-III. Refer to
BRC-26, "CONSULT-III Function".
Is any DTC detected?
YES >> Repair or replace the malfunctioning part.
NO >> Replace BCM. Refer to BCS-82, "Exploded View".

Revision: 2011 November BCS-36 2011 G Sedan

 B2562 LOW VOLTAGE
< DTC/CIRCUIT DIAGNOSIS >
B2562 LOW VOLTAGE
A
DTC Logic INFOID:0000000006211078

DTC DETECTION LOGIC B

CONSULT-III display
DTC DTC Detection Condition Possible cause
description C
When the power supply voltage to BCM remains less Harness or connector (power supply
B2562 LOW VOLTAGE
than 8.8 V for 120 seconds or more circuit)
D
DTC CONFIRMATION PROCEDURE
1.DTC CONFIRMATION
1. Erase DTC. E
2. Turn ignition switch OFF.
3. Perform the “Self Diagnostic Result” of CONSULT-III, when passed 120 seconds or more after the ignition
switch is turned ON. F
Is any DTC detected?
YES >> Refer to BCS-37, "Diagnosis Procedure".
NO >> INSPECTION END G
Diagnosis Procedure INFOID:0000000006211079

1.CHECK POWER SUPPLY CIRCUIT H

Check BCM power supply circuit. Refer to BCS-38, "Diagnosis Procedure".

Is the circuit normal?
I
YES >> Replace BCM. Refer to BCS-82, "Exploded View".
NO >> Repair the malfunctioning part.
J

BCS

Revision: 2011 November BCS-37 2011 G Sedan

 POWER SUPPLY AND GROUND CIRCUIT
< DTC/CIRCUIT DIAGNOSIS >
POWER SUPPLY AND GROUND CIRCUIT
Diagnosis Procedure INFOID:0000000006211080

1.CHECK FUSE AND FUSIBLE LINK

Check that the following fuse and fusible link are not blown.

Signal name Fuse and fusible link No.

K
Battery power supply
10
Is the fuse fusing?
YES >> Replace the blown fuse or fusible link after repairing the affected circuit if a fuse or fusible link is
blown.
NO >> GO TO 2.
2.CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connectors.
3. Check voltage between BCM harness connector and ground.

Terminals
(+) (−) Voltage
BCM (Approx.)

Connector Terminal
Ground
M118 1
Battery voltage
M119 11
Is the measurement value normal?
YES >> GO TO 3.
NO >> Repair harness or connector.
3.CHECK GROUND CIRCUIT
Check continuity between BCM harness connector and ground.

BCM
Continuity
Connector Terminal Ground
M119 13 Existed
Does continuity exist?
YES >> INSPECTION END
NO >> Repair harness or connector.

Revision: 2011 November BCS-38 2011 G Sedan

 COMBINATION SWITCH INPUT CIRCUIT
< DTC/CIRCUIT DIAGNOSIS >
COMBINATION SWITCH INPUT CIRCUIT
A
Diagnosis Procedure INFOID:0000000006211081

1.CHECK INPUT 1 - 5 SYSTEM CIRCUIT FOR OPEN B

1. Turn the ignition switch OFF.
2. Disconnect the BCM and combination switch connectors.
3. Check continuity between BCM harness connector and combination switch harness connector. C

BCM Combination switch

System Continuity
Connector Terminal Connector Terminal D
INPUT 1 107 11
INPUT 2 109 9
E
INPUT 3 M122 88 M33 7 Existed
INPUT 4 108 10
INPUT 5 87 13 F
Does continuity exist?
YES >> GO TO 2.
NO >> Repair the harnesses or connectors. G

2.CHECK INPUT 1 - 5 SYSTEM CIRCUIT FOR SHORT

Check for continuity between BCM harness connector and ground. H

BCM
System Continuity
Connector Terminal I
INPUT 1 107
INPUT 2 109 Ground
J
INPUT 3 M122 88 Not existed
INPUT 4 108
INPUT 5 87 K
Does continuity exist?
YES >> Repair the harnesses or connectors.
NO >> GO TO 3. L

3.CHECK BCM OUTPUT VOLTAGE

1. Connect the BCM connector. BCS
2. Check voltage between BCM harness connector and ground.

Terminals N
(+) (−) Voltage
System
BCM (Approx.)
O
Connector Terminal
INPUT 1 107
Ground
INPUT 2 109 P
Refer to BCS-
INPUT 3 M122 88 43, "Refer-
ence Value".
INPUT 4 108
INPUT 5 87
Is the measurement value normal?
YES >> GO TO 4.
NO >> Replace BCM. Refer to BCS-82, "Exploded View".

Revision: 2011 November BCS-39 2011 G Sedan

 COMBINATION SWITCH INPUT CIRCUIT
< DTC/CIRCUIT DIAGNOSIS >
4.CHECK BCM INPUT SIGNAL
1. Connect the combination switch connector.
2. Turn ON any switch in the system that is malfunctioning.
3. Check voltage between BCM harness connector and ground.

Terminals
(+) (−) Voltage
System
BCM (Approx.)

Connector Terminal
INPUT 1 107
Ground
INPUT 2 109
Refer to BCS-
INPUT 3 M122 88 43, "Refer-
ence Value".
INPUT 4 108
INPUT 5 87
Is the measurement value normal when any of the switches is turned ON?
YES >> Replace BCM. Refer to BCS-82, "Exploded View".
NO >> Replace the combination switch.

Revision: 2011 November BCS-40 2011 G Sedan

 COMBINATION SWITCH OUTPUT CIRCUIT
< DTC/CIRCUIT DIAGNOSIS >
COMBINATION SWITCH OUTPUT CIRCUIT
A
Diagnosis Procedure INFOID:0000000006211082

1.CHECK OUTPUT 1 - 5 SYSTEM CIRCUIT FOR OPEN B

1. Turn the ignition switch OFF.
2. Disconnect the BCM and combination switch connectors.
NOTE: C
BCM connector disconnects M123 only.
3. Check continuity between BCM harness connector and combination switch harness connector.
D
BCM Combination switch
System Continuity
Connector Terminal Connector Terminal
OUTPUT 1 143 12 E
OUTPUT 2 144 14
OUTPUT 3 M123 145 M33 5 Existed
F
OUTPUT 4 146 2
OUTPUT 5 142 8
Does continuity exist? G
YES >> GO TO 2.
NO >> Repair the harnesses or connectors.
2.CHECK OUTPUT 1 - 5 SYSTEM CIRCUIT FOR SHORT H

Check for continuity between BCM harness connector and ground.

I
BCM
System Continuity
Connector Terminal
OUTPUT 1 143 J
OUTPUT 2 144 Ground
OUTPUT 3 M123 145 Not existed
K
OUTPUT 4 146
OUTPUT 5 142
Does continuity exist? L
YES >> Repair the harnesses or connectors.
NO >> GO TO 3.
3.CHECK COMBINATION SWITCH INTERNAL CIRCUIT BCS

1. Connect the combination switch connector.

2. Turn ON any switch in the system that is malfunctioning.
N
3. Check voltage between combination switch harness connector and ground.
NOTE:
Check that the combination switch outputs a signal from combination switch input system.
O

Revision: 2011 November BCS-41 2011 G Sedan

 COMBINATION SWITCH OUTPUT CIRCUIT
< DTC/CIRCUIT DIAGNOSIS >

Terminals
(+) (−)
System Value (Approx.)
Combination switch
Connector Terminal
OUTPUT 1 12
OUTPUT 2 14
Ground
OUTPUT 3 5
OUTPUT 4 M33 2

OUTPUT 5 8 JPMIA0041GB

1.4 V
Is the measurement value normal when any of the switches is turned ON?
YES >> Replace BCM. Refer to BCS-82, "Exploded View".
NO >> Replace the combination switch.

Revision: 2011 November BCS-42 2011 G Sedan

 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION >
ECU DIAGNOSIS INFORMATION A
BCM (BODY CONTROL MODULE)
Reference Value INFOID:0000000006211083
B

VALUES ON THE DIAGNOSIS TOOL

CONSULT-III MONITOR ITEM C
Monitor Item Condition Value/Status
Other than front wiper switch HI Off
FR WIPER HI D
Front wiper switch HI On
Other than front wiper switch LO Off
FR WIPER LOW
Front wiper switch LO On
E
Front washer switch OFF Off
FR WASHER SW
Front washer switch ON On
Other than front wiper switch INT/AUTO Off F
FR WIPER INT
Front wiper switch INT/AUTO On
Front wiper is not in STOP position Off
FR WIPER STOP G
Front wiper is in STOP position On
Wiper volume dial posi-
INT VOLUME Wiper volume dial is in a dial position 1 - 7
tion
H
Other than turn signal switch RH Off
TURN SIGNAL R
Turn signal switch RH On
Other than turn signal switch LH Off I
TURN SIGNAL L
Turn signal switch LH On
Other than lighting switch 1ST and 2ND Off
TAIL LAMP SW J
Lighting switch 1ST or 2ND On
Other than lighting switch HI Off
HI BEAM SW
Lighting switch HI On K
Other than lighting switch 2ND Off
HEAD LAMP SW 1
Lighting switch 2ND On
L
Other than lighting switch 2ND Off
HEAD LAMP SW 2
Lighting switch 2ND On
Other than lighting switch PASS Off BCS
PASSING SW
Lighting switch PASS On
Other than lighting switch AUTO Off
AUTO LIGHT SW N
Lighting switch AUTO On
Front fog lamp switch OFF Off
FR FOG SW
Front fog lamp switch ON On
O
NOTE:
RR FOG SW Off
The item is indicated, but not monitored.
Driver door closed Off P
DOOR SW-DR
Driver door opened On
Passenger door closed Off
DOOR SW-AS
Passenger door opened On
Rear RH door closed Off
DOOR SW-RR
Rear LH door opened On

Revision: 2011 November BCS-43 2011 G Sedan

 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION >
Monitor Item Condition Value/Status
Rear LH door closed Off
DOOR SW-RL
Rear LH door opened On
NOTE:
DOOR SW-BK Off
The item is indicated, but not monitored.
Other than power door lock switch LOCK Off
CDL LOCK SW
Power door lock switch LOCK On
Other than power door lock switch UNLOCK Off
CDL UNLOCK SW
Power door lock switch UNLOCK On
Other than driver door key cylinder LOCK Off
KEY CYL LK-SW
Driver door key cylinder LOCK On
Other than driver door key cylinder UNLOCK Off
KEY CYL UN-SW
Driver door key cylinder LOCK On
NOTE:
KEY CYL SW-TR Off
The item is indicated, but not monitored.
Hazard switch is OFF Off
HAZARD SW
Hazard switch is ON On
NOTE:
REAR DEF SW Off
The item is indicated, but not monitored.
NOTE:
H/L WASH SW Off
The item is indicated, but not monitored.
Trunk lid opener cancel switch OFF Off
TR CANCEL SW
Trunk lid opener cancel switch ON On
Trunk lid opener switch OFF Off
TR/BD OPEN SW
While the trunk lid opener switch is turned ON On
Trunk lid closed Off
TRNK/HAT MNTR
Trunk lid opened On
LOCK button of the Intelligent Key is not pressed Off
RKE-LOCK
LOCK button of the Intelligent Key is pressed On
UNLOCK button of the Intelligent Key is not pressed Off
RKE-UNLOCK
UNLOCK button of the Intelligent Key is pressed On
TRUNK OPEN button of the Intelligent Key is not pressed Off
RKE-TR/BD
TRUNK OPEN button of the Intelligent Key is pressed On
PANIC button of the Intelligent Key is not pressed Off
RKE-PANIC
PANIC button of the Intelligent Key is pressed On
UNLOCK button of the Intelligent Key is not pressed Off
RKE-P/W OPEN
UNLOCK button of the Intelligent Key is pressed and held On
LOCK/UNLOCK button of the Intelligent Key is not pressed and held simulta-
Off
RKE-MODE CHG neously
LOCK/UNLOCK button of the Intelligent Key is pressed and held simultaneously On
Bright outside of the vehicle Close to 5 V
OPTICAL SENSOR
Dark outside of the vehicle Close to 0 V
Driver door request switch is not pressed Off
REQ SW -DR
Driver door request switch is pressed On
Passenger door request switch is not pressed Off
REQ SW -AS
Passenger door request switch is pressed On

Revision: 2011 November BCS-44 2011 G Sedan

 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION >
Monitor Item Condition Value/Status
A
NOTE:
REQ SW -RR Off
The item is indicated, but not monitored.
NOTE:
REQ SW -RL Off B
The item is indicated, but not monitored.
Trunk lid opener request switch is not pressed Off
REQ SW -BD/TR
Trunk lid opener request switch is pressed On
C
Push-button ignition switch (push switch) is not pressed Off
PUSH SW
Push-button ignition switch (push switch) is pressed On
Ignition switch in OFF or ACC position Off D
IGN RLY2 -F/B
Ignition switch in ON position On
NOTE:
ACC RLY -F/B Off E
The item is indicated, but not monitored.
The clutch pedal is not depressed Off
CLUCH SW
The clutch pedal is depressed On
F
The brake pedal is depressed when No. 7 fuse is blown Off
BRAKE SW 1 The brake pedal is not depressed when No. 7 fuse is blown, or No. 7 fuse is nor-
On
mal
G
The brake pedal is not depressed Off
BRAKE SW 2
The brake pedal is depressed On
• Selector lever in P position (Except M/T models) H
Off
• The clutch pedal is depressed (M/T models)
DETE/CANCL SW
• Selector lever in any position other than P (Except M/T models)
On
• The clutch pedal is not depressed (M/T models) I
Selector lever in any position other than P and N Off
SFT PN/N SW
Selector lever in P or N position On
J
Steering is unlocked Off
S/L -LOCK
Steering is locked On
Steering is locked Off K
S/L -UNLOCK
Steering is unlocked On
Ignition switch in OFF or ACC position Off
S/L RELAY-F/B L
Ignition switch in ON position On
Driver door is unlocked Off
UNLK SEN -DR
Driver door is locked On
BCS
Push-button ignition switch (push-switch) is not pressed Off
PUSH SW -IPDM
Push-button ignition switch (push-switch) is pressed On
Ignition switch in OFF or ACC position Off N
IGN RLY1 -F/B
Ignition switch in ON position On
Selector lever in any position other than P Off
DETE SW -IPDM O
Selector lever in P position On
• Selector lever in any position other than P and N (Except M/T models)
Off
• The clutch pedal is not depressed (M/T models)
SFT PN -IPDM P
• Selector lever in P or N position (Except M/T models)
On
• The clutch pedal is depressed (M/T models)
Selector lever in any position other than P Off
SFT P -MET
Selector lever in P position On
Selector lever in any position other than N Off
SFT N -MET
Selector lever in N position On

Revision: 2011 November BCS-45 2011 G Sedan

 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION >
Monitor Item Condition Value/Status
Engine stopped Stop
While the engine stalls Stall
ENGINE STATE
At engine cranking Crank
Engine running Run
Steering is unlocked Off
S/L LOCK-IPDM
Steering is locked On
Steering is locked Off
S/L UNLK-IPDM
Steering is unlocked On
Steering lock system is not the LOCK condition and the changing condition from
Off
LOCK to UNLOCK
S/L RELAY-REQ
Steering lock system is the LOCK condition or the changing condition from LOCK
On
to UNLOCK
Equivalent to speed-
VEH SPEED 1 While driving
ometer reading
Equivalent to speed-
VEH SPEED 2 While driving
ometer reading
Driver door is locked LOCK
DOOR STAT-DR Wait with selective UNLOCK operation (60 seconds) READY
Driver door is unlocked UNLOCK
Passenger door is locked LOCK
DOOR STAT-AS Wait with selective UNLOCK operation (60 seconds) READY
Passenger door is unlocked UNLOCK
Steering is locked Reset
ID OK FLAG
Steering is unlocked Set
The engine start is prohibited Reset
PRMT ENG STRT
The engine start is permitted Set
NOTE:
PRMT RKE STRT Reset
The item is indicated, but not monitored.
The Intelligent Key is not inserted into key slot Off
KEY SW -SLOT
The Intelligent Key is inserted into key slot On
Operation frequency of
RKE OPE COUN1 During the operation of the Intelligent Key
the Intelligent Key
NOTE:
RKE OPE COUN2 —
The item is indicated, but not monitored.
The key ID that the key slot receives is not recognized by any key ID registered
Yet
to BCM.
CONFRM ID ALL
The key ID that the key slot receives is recognized by any key ID registered to
Done
BCM.
The key ID that the key slot receives is not recognized by the fourth key ID regis-
Yet
tered to BCM.
CONFIRM ID4
The key ID that the key slot receives is recognized by the fourth key ID registered
Done
to BCM.
The key ID that the key slot receives is not recognized by the third key ID regis-
Yet
tered to BCM.
CONFIRM ID3
The key ID that the key slot receives is recognized by the third key ID registered
Done
to BCM.

Revision: 2011 November BCS-46 2011 G Sedan

 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION >
Monitor Item Condition Value/Status
A
The key ID that the key slot receives is not recognized by the second key ID reg-
Yet
istered to BCM.
CONFIRM ID2
The key ID that the key slot receives is recognized by the second key ID regis-
Done B
tered to BCM.
The key ID that the key slot receives is not recognized by the first key ID regis-
Yet
tered to BCM.
CONFIRM ID1 C
The key ID that the key slot receives is recognized by the first key ID registered
Done
to BCM.
The ID of fourth Intelligent Key is not registered to BCM Yet
TP 4 D
The ID of fourth Intelligent Key is registered to BCM Done
The ID of third Intelligent Key is not registered to BCM Yet
TP 3
The ID of third Intelligent Key is registered to BCM Done E
The ID of second Intelligent Key is not registered to BCM Yet
TP 2
The ID of second Intelligent Key is registered to BCM Done
The ID of first Intelligent Key is not registered to BCM Yet F
TP 1
The ID of first Intelligent Key is registered to BCM Done
Air pressure of front LH
AIR PRESS FL Ignition switch ON (Only when the signal from the transmitter is received) G
tire
Air pressure of front RH
AIR PRESS FR Ignition switch ON (Only when the signal from the transmitter is received)
tire
H
Air pressure of rear RH
AIR PRESS RR Ignition switch ON (Only when the signal from the transmitter is received)
tire
Air pressure of rear LH
AIR PRESS RL Ignition switch ON (Only when the signal from the transmitter is received) I
tire
ID of front LH tire transmitter is registered Done
ID REGST FL1
ID of front LH tire transmitter is not registered Yet
J
ID of front RH tire transmitter is registered Done
ID REGST FR1
ID of front RH tire transmitter is not registered Yet
ID of rear RH tire transmitter is registered Done K
ID REGST RR1
ID of rear RH tire transmitter is not registered Yet
ID of rear LH tire transmitter is registered Done
ID REGST RL1 L
ID of rear LH tire transmitter is not registered Yet
Tire pressure indicator OFF Off
WARNING LAMP
Tire pressure indicator ON On BCS
Tire pressure warning alarm is not sounding Off
BUZZER
Tire pressure warning alarm is sounding On
N

Revision: 2011 November BCS-47 2011 G Sedan

 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION >
TERMINAL LAYOUT

JPMIA0062ZZ

PHYSICAL VALUES

Revision: 2011 November BCS-48 2011 G Sedan

 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION >

Terminal No. Description A

(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ – Output
1 B
Ground Battery power supply Input Ignition switch OFF Battery voltage
(W)
2 P/W power supply
Ground Output Ignition switch OFF 12 V
(Y) (BAT) C
3 P/W power supply
Ground Output Ignition switch ON 12 V
(BG) (RAP)
Interior room lamp battery saver is activated. D
0V
(Cuts the interior room lamp power supply)
4 Interior room lamp Interior room lamp battery saver is not acti-
Ground Output
(LG) power supply vated.
12 V E
(Outputs the interior room lamp power sup-
ply)
UNLOCK (Actuator is acti-
12 V F
5 Passenger door UN- Passenger vated)
Ground Output
(P) LOCK door Other than UNLOCK) Ac-
0V
tuator is not activated
ON 0V G
7
Ground Step lamp Output Step lamp
(SB) OFF 12 V
LOCK
12 V H
8 All doors, fuel lid All doors, fuel (Actuator is activated)
Ground Output
(V) LOCK lid Other than LOCK
0V
(Actuator is not activated)
I
UNLOCK
12 V
9 Driver door, fuel lid Driver door, (Actuator is activated)
Ground Output
(G) UNLOCK fuel lid Other than UNLOCK
(Actuator is not activated)
0V J

UNLOCK
Rear RH door and Rear RH door 12 V
10 (Actuator is activated)
Ground rear LH door UN- Output and rear LH K
(P) Other than UNLOCK
LOCK door 0V
(Actuator is not activated)
11
Ground Battery power supply Input Ignition switch OFF Battery voltage L
(R)
13
Ground Ground — Ignition switch ON 0V
(B)
OFF 0V
BCS

NOTE:
When the illumination brighten-
ing/dimming level is in the neutral N
position
14 Push-button ignition
(W) Ground switch illumination Output Tail lamp
ground ON O

P
JSNIA0010GB

OFF (LOCK indicator is

15 Battery voltage
Ground ACC indicator lamp Output Ignition switch not illuminated)
(BG)
ACC 0V

Revision: 2011 November BCS-49 2011 G Sedan

 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION >
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ – Output
Turn signal switch OFF 0V

17 Turn signal RH Ignition switch

Ground Output
(W) (Front) ON Turn signal switch RH

PKID0926E

6.5 V
Turn signal switch OFF 0V

18 Ignition switch
Ground Turn signal LH (Front) Output
(BG) ON Turn signal switch LH

PKID0926E

6.5 V

19 Room lamp timer Interior room OFF 12 V

Ground Output
(V) control lamp ON 0V
Turn signal switch OFF 0V

20 Ignition switch
Ground Turn signal RH (Rear) Output
(V) ON Turn signal switch RH

PKID0926E

6.5 V
OPEN
(Trunk lid opener actuator 12 V
23 is activated)
Ground Trunk lid open Output Trunk lid
(LG) Other than OPEN
(Trunk lid opener actuator 0V
is not activated)
Turn signal switch OFF 0V

25
Ignition switch
(Y) Ground Turn signal LH (Rear) Output
ON Turn signal switch LH

PKID0926E

6.5 V

30 Trunk room ON 0V
Ground Trunk room lamp Output
(P) lamp OFF 12 V

Revision: 2011 November BCS-50 2011 G Sedan

 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION >
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ – Output

When Intelligent Key is in

the passenger compart- C
ment

JMKIA0062GB

34 Trunk room antenna Ignition switch

D
Ground Output
(SB) (−) OFF

E
When Intelligent Key is not
in the passenger compart-
ment
F
JMKIA0063GB

When Intelligent Key is in H

the passenger compart-
ment

JMKIA0062GB
I
35 Trunk room antenna Ignition switch
Ground Output
(V) (+) OFF
J

When Intelligent Key is not

in the passenger compart-
K
ment

JMKIA0063GB
L

BCS
When Intelligent Key is in
the antenna detection
area
N
When the trunk JMKIA0062GB
lid opener re-
38 Rear bumper anten-
Ground Output quest switch is
(B) na (−)
operated with
O
ignition switch
OFF
When Intelligent Key is not P
in the antenna detection
area

JMKIA0063GB

Revision: 2011 November BCS-51 2011 G Sedan

 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION >
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ – Output

When Intelligent Key is in

the antenna detection
area

When the trunk JMKIA0062GB

lid opener re-
39 Rear bumper anten-
Ground Output quest switch is
(W) na (+)
operated with
ignition switch
OFF
When Intelligent Key is not
in the antenna detection
area

JMKIA0063GB

47 Ignition relay (IPDM OFF or ACC 12 V

Ground Output Ignition switch
(Y) E/R) control ON 0V

50 Trunk room lamp Trunk room OFF (Trunk lid is closed)

Ground Input
(BG) switch lamp switch

JPMIA0011GB

11.8 V
ON (Trunk lid is opened) 0V
When selector lever is in P
Ignition switch 12 V
or N position
ON (A/T mod-
els) When selector lever is not
0V
52 in P or N position
Ground Starter relay control Output
(R) When the clutch pedal is
Ignition switch Battery voltage
depressed
ON (M/T mod-
els) When the clutch pedal is
0V
not depressed
ON (Pressed) 0V

Trunk lid open-

61 Trunk lid opener re-
Ground Input er request
(SB) quest switch OFF (Not pressed)
switch

JPMIA0016GB

1.0 V
Intelligent Key warn- Intelligent Key Sounding 0V
64
Ground ing buzzer (Engine Output warning buzzer
(G) Not sounding 12 V
room) (Engine room)

Revision: 2011 November BCS-52 2011 G Sedan

 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION >
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ – Output
Pressed 0V
B

67
Ground
Trunk lid opener
Input
Trunk lid open- C
(GR) switch er switch Not pressed

D
JPMIA0011GB

11.8 V

OFF (When rear RH door

closes) F
68 Rear RH door
Ground Rear RH door switch Input
(BG) switch
JPMIA0011GB

11.8 V G
ON (When rear RH door
0V
opens)
H

I
OFF (When rear LH door
69 Rear LH door closes)
Ground Rear LH door switch Input
(L) switch
J
JPMIA0011GB

11.8 V
ON (When rear LH door
0V K
opens)

L
When Intelligent Key is in
the passenger compart-
ment
BCS
JMKIA0062GB

72 Room antenna 2 (−) Ignition switch

Ground Output N
(R) (Center console) OFF

When Intelligent Key is not O

in the passenger compart-
ment

JMKIA0063GB
P

Revision: 2011 November BCS-53 2011 G Sedan

 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION >
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ – Output

When Intelligent Key is in

the passenger compart-
ment

JMKIA0062GB

73 Room antenna 2 (+) Ignition switch

Ground Output
(G) (Center console) OFF

When Intelligent Key is not

in the passenger compart-
ment

JMKIA0063GB

When Intelligent Key is in

the antenna detection
area

When the pas- JMKIA0062GB

senger door re-
74 Passenger door an-
Ground Output quest switch is
(SB) tenna (−)
operated with
ignition switch
OFF
When Intelligent Key is not
in the antenna detection
area

JMKIA0063GB

When Intelligent Key is in

the antenna detection
area

When the pas- JMKIA0062GB

senger door re-
75 Passenger door an-
Ground Output quest switch is
(BR) tenna (+)
operated with
ignition switch
OFF
When Intelligent Key is not
in the antenna detection
area

JMKIA0063GB

Revision: 2011 November BCS-54 2011 G Sedan

 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION >
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ – Output

When Intelligent Key is in

the antenna detection C
area

When the driv- JMKIA0062GB

76 Driver door antenna

er door request D
Ground Output switch is oper-
(V) (−)
ated with igni-
tion switch
OFF E
When Intelligent Key is not
in the antenna detection
area
F
JMKIA0063GB

When Intelligent Key is in H

the antenna detection
area

When the driv- JMKIA0062GB

I
er door request
77 Driver door antenna
Ground Output switch is oper-
(LG) (+)
ated with igni-
tion switch J
OFF
When Intelligent Key is not
in the antenna detection
K
area

JMKIA0063GB
L

BCS
When Intelligent Key is in
the passenger compart-
ment
N
JMKIA0062GB

78 Room antenna 1 (−) Ignition switch

Ground Output
(Y) (Instrument panel) OFF O

When Intelligent Key is not P

in the passenger compart-
ment

JMKIA0063GB

Revision: 2011 November BCS-55 2011 G Sedan

 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION >
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ – Output

When Intelligent Key is in

the passenger compart-
ment

JMKIA0062GB

79 Room antenna 1 (+) Ignition switch

Ground Output
(BR) (Instrument panel) OFF

When Intelligent Key is not

in the passenger compart-
ment

JMKIA0063GB

Ignition switch is pressed Just after pressing ignition

80 Input/
Ground NATS antenna amp. During waiting while inserting the Intelli- switch. Pointer of tester should
(GR) Output
gent Key into the key slot. move.
Ignition switch is pressed Just after pressing ignition
81 Input/
Ground NATS antenna amp. During waiting while inserting the Intelli- switch. Pointer of tester should
(W) Output
gent Key into the key slot. move.

82 Ignition relay [Fuse OFF or ACC 0V

Ground Output Ignition switch
(SB) block (J/B)] control ON 12 V

During waiting

JMKIA0064GB
Remote keyless entry
83 Input/
Ground receiver communica-
(Y) Output
tion

When operating either button on the Intelli-

gent Key

JMKIA0065GB

Revision: 2011 November BCS-56 2011 G Sedan

 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION >
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ – Output

All switches OFF

(Wiper volume dial 4) C

JPMIA0041GB

1.4 V D

E
87 Combination switch Combination Front fog lamp switch ON
Ground Input
(Y) INPUT 5 switch (Wiper volume dial 4)
F
JPMIA0037GB

1.3 V
G

Any of the conditions be-

low with all switches OFF
• Wiper volume dial 1
H
• Wiper volume dial 2
• Wiper volume dial 6
• Wiper volume dial 7
JPMIA0040GB
I
1.3 V

BCS

Revision: 2011 November BCS-57 2011 G Sedan

 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION >
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ – Output

All switches OFF

(Wiper volume dial 4)

JPMIA0041GB

1.4 V

Lighting switch HI
(Wiper volume dial 4)

JPMIA0036GB

88 Combination switch Combination 1.3 V

Ground Input
(BG) INPUT 3 switch

Lighting switch 2ND

(Wiper volume dial 4)

JPMIA0037GB

1.3 V

Any of the conditions be-

low with all switches OFF
• Wiper volume dial 1
• Wiper volume dial 2
• Wiper volume dial 3
JPMIA0040GB

1.3 V
Push-button ig- Pressed 0V
89 Push-button ignition
Ground Input nition switch
(BR) switch (Push switch) Not pressed Battery voltage
(push switch)
90 Input/
Ground CAN-L — —
(P) Output
91 Input/
Ground CAN-H — —
(L) Output
OFF 0V

92 Key slot illumi-

Ground Key slot illumination Output Blinking
(LG) nation

JPMIA0015GB

6.5 V
ON 12 V

Revision: 2011 November BCS-58 2011 G Sedan

 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION >
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ – Output
OFF (LOCK indicator is
93 Battery voltage B
Ground ON indicator lamp Output Ignition switch not illuminated)
(GR)
ON 0V

95 OFF 0V
Ground ACC relay control Output Ignition switch C
(BG) ACC or ON 12 V
A/T shift selector (De-
96
Ground tention switch) power Output — 12 V
(GR) D
supply

97 Steering lock condi- LOCK status 0V

Ground Input Steering lock
(L) tion No. 1 UNLOCK status 12 V E
98 Steering lock condi- LOCK status 12 V
Ground Input Steering lock
(P) tion No. 2 UNLOCK status 0V
Selector lever P posi- P position 0V F
tion switch (A/T mod- Selector lever
els) Any position other than P 12 V

OFF (Clutch pedal is de- G

ASCD clutch switch 0V
99 ASCD clutch pressed)
(M/T models without
(R)*1 Ground Input switch ON (Clutch pedal is not
ICC) 12 V
(BR)*2 depressed) H
OFF (Clutch pedal is de-
0V
ICC clutch switch (M/ ICC clutch pressed)
T models with ICC) switch ON (Clutch pedal is not I
12 V
depressed)
ON (Pressed) 0V
J

Passenger
100 Passenger door re-
Ground Input door request K
(Y) quest switch OFF (Not pressed)
switch

JPMIA0016GB L
1.0 V
ON (Pressed) 0V
BCS

101 Driver door request Driver door re-

Ground Input N
(P) switch quest switch OFF (Not pressed)

JPMIA0016GB O
1.0 V

102 Blower fan motor re- OFF or ACC 0V

Ground Output Ignition switch P
(BG) lay control ON 12 V
Remote keyless entry
103
Ground receiver power sup- Output Ignition switch OFF 12 V
(P)
ply

106 Steering lock unit OFF or ACC 12 V

Ground Output Ignition switch
(SB) power supply ON 0V

Revision: 2011 November BCS-59 2011 G Sedan

 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION >
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ – Output

All switches OFF

JPMIA0041GB

1.4 V

Turn signal switch LH

JPMIA0037GB

1.3 V

Combination
107 Combination switch switch
Ground Input Turn signal switch RH
(LG) INPUT 1 (Wiper volume
dial 4)

JPMIA0036GB

1.3 V

Front wiper switch LO

JPMIA0038GB

1.3 V

Front washer switch ON

JPMIA0039GB

1.3 V

Revision: 2011 November BCS-60 2011 G Sedan

 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION >
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ – Output

All switches OFF

(Wiper volume dial 4) C

JPMIA0041GB

1.4 V D

E
Lighting switch AUTO
(Wiper volume dial 4)
F
JPMIA0038GB

108 Combination switch Combination 1.3 V

Ground Input G
(R) INPUT 4 switch

Lighting switch 1ST

H
(Wiper volume dial 4)

JPMIA0036GB
I
1.3 V

J
Any of the conditions be-
low with all switches OFF
• Wiper volume dial 1
K
• Wiper volume dial 5
• Wiper volume dial 6
JPMIA0039GB

1.3 V L

BCS

Revision: 2011 November BCS-61 2011 G Sedan

 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION >
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ – Output

All switches OFF

JPMIA0041GB

1.4 V

Lighting switch PASS

JPMIA0037GB

1.3 V

Combination
109 Combination switch switch
Ground Input Lighting switch 2ND
(W) INPUT 2 (Wiper volume
dial 4)

JPMIA0036GB

1.3 V

Front wiper switch INT/

AUTO

JPMIA0038GB

1.3 V

Front wiper switch HI

JPMIA0040GB

1.3 V
ON 0V

110
Ground Hazard switch Input Hazard switch
(G) OFF

JPMIA0012GB

1.1 V

Revision: 2011 November BCS-62 2011 G Sedan

 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION >
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ – Output
LOCK status 12 V
B

C
LOCK or UNLOCK
111 Steering lock unit Input/
Ground Steering lock
(Y) communication Output D
JMKIA0066GB

For 15 seconds after UN-

LOCK
12 V E
15 seconds or later after
0V
UNLOCK
F

G
112 Light and rain sensor Input/
Ground Ignition switch ON
(R) serial link Output

H
JPMIA0156GB

8.7 V
When bright outside of the
Close to 5 V I
113 Ignition switch vehicle
Ground Optical sensor Input
(BG) ON When dark outside of the
Close to 0 V
vehicle
OFF (Clutch pedal is not
J
0V
114 Clutch interlock Clutch interlock depressed)
Ground Input
(R) switch switch ON (Clutch pedal is de-
Battery voltage
pressed) K
116
Ground Stop lamp switch 1 Input — Battery voltage
(SB)
OFF (Brake pedal is not L
0V
Stop lamp switch 2 Stop lamp depressed)
(Without ICC) switch ON (Brake pedal is de-
Battery voltage
118 pressed) BCS
Ground Input
(BR) Stop lamp switch OFF (Brake pedal is not
0V
Stop lamp switch 2 depressed) and ICC brake hold relay OFF
(With ICC) Stop lamp switch ON (Brake pedal is de- N
Battery voltage
pressed) or ICC brake hold relay ON

LOCK status
(Unlock sensor switch
Front door lock as- OFF) P
119
Ground sembly driver side Input Driver door
(SB)
(Unlock sensor)
JPMIA0012GB

1.1 V
UNLOCK status
(Unlock switch sensor 0V
ON)

Revision: 2011 November BCS-63 2011 G Sedan

 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION >
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ – Output
When the Intelligent Key is inserted into key
12 V
121 slot
Ground Key slot switch Input
(SB) When the Intelligent Key is not inserted into
0V
key slot

123 OFF or ACC 0V

Ground IGN feedback Input Ignition switch
(V) ON Battery voltage

124 Passenger door Passenger OFF (Door close)

Ground Input
(R) switch door switch

JPMIA0011GB

11.8 V
ON (Door open) 0V

Trunk lid open- CANCEL

129 Trunk lid opener can-
Ground Input er cancel
(BG) cel switch
switch
JPMIA0012GB

1.1 V
ON 0V

132 Power window switch Input/ Ignition switch ON

Ground
(V) communication Output

JPMIA0013GB

10.2 V
Ignition switch OFF or ACC 12 V
ON (Tail lamps OFF) 9.5 V
NOTE:
The pulse width of this wave is
varied by the illumination bright-
ening/dimming level.
Push-button ig-
133 Push-button ignition
Ground Output nition switch il- ON (Tail lamps ON)
(L) switch illumination
lumination

JPMIA0159GB

OFF 0V

134 LOCK indicator OFF Battery voltage

Ground LOCK indicator lamp Output
(LG) lamp ON 0V
137 Receiver and sensor
Ground Input Ignition switch ON 0V
(BG) ground

Revision: 2011 November BCS-64 2011 G Sedan

 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION >
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ – Output

138 Receiver and sensor OFF 0V

(V)
Ground
power supply
Output Ignition switch B
ACC or ON 5.0 V

Standby state

139 Tire pressure receiv- Input/ Ignition switch OCC3881D

Ground
(L) er communication Output ON E

When receiving the signal

from the transmitter F

OCC3880D G
140 Selector lever P/N P or N position 12 V
Ground Input Selector lever
(B) position Except P and N positions 0V
H
ON 0V

141 Security indica-

Ground Security indicator Output Blinking
(W) tor
J

JPMIA0014GB

11.3 V
K
OFF 12 V
All switches OFF 0V
Lighting switch 1ST L
Lighting switch HI
Combination
142
Combination switch switch Lighting switch 2ND
(BR) Ground Output BCS
OUTPUT 5 (Wiper volume
dial 4)
Turn signal switch RH
JPMIA0031GB N
10.7 V
All switches OFF
0V
(Wiper volume dial 4)
O
Front wiper switch HI
(Wiper volume dial 4)
143 Combination switch Combination Any of the conditions be- P
Ground Output
(P) OUTPUT 1 switch low with all switches OFF
• Wiper volume dial 1
• Wiper volume dial 2
• Wiper volume dial 3
• Wiper volume dial 6 JPMIA0032GB
• Wiper volume dial 7 10.7 V

Revision: 2011 November BCS-65 2011 G Sedan

 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION >
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ – Output
All switches OFF
0V
(Wiper volume dial 4)
Front washer switch ON
(Wiper volume dial 4)
144 Combination switch Combination
Ground Output
(G) OUTPUT 2 switch Any of the conditions be-
low with all switches OFF
• Wiper volume dial 1
• Wiper volume dial 5
• Wiper volume dial 6 JPMIA0033GB

10.7 V
All switches OFF 0V
Front wiper switch INT/
AUTO
Combination
Front wiper switch LO
145 Combination switch switch
Ground Output
(L) OUTPUT 3 (Wiper volume
dial 4)
Lighting switch AUTO
JPMIA0034GB

10.7 V
All switches OFF 0V
Front fog lamp switch ON
Lighting switch 2ND
Combination
146 Combination switch switch Lighting switch PASS
Ground Output
(SB) OUTPUT 4 (Wiper volume
dial 4)
Turn signal switch LH
JPMIA0035GB

10.7 V

150 Driver door OFF (Door close)

Ground Driver door switch Input
(GR) switch

JPMIA0011GB

11.8 V
ON (Door open) 0V

151 Rear window defog- Rear window Active 0V

Ground Output
(G) ger relay control defogger Not activated Battery voltage
• *1: A/T models
• *2: M/T models

Revision: 2011 November BCS-66 2011 G Sedan

 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION >
Wiring Diagram - BCM - INFOID:0000000006211084

BCS

JCMWM9738GB
P

Revision: 2011 November BCS-67 2011 G Sedan

 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION >

JCMWM9739GB

Revision: 2011 November BCS-68 2011 G Sedan

 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION >

BCS

JCMWM9740GB

Revision: 2011 November BCS-69 2011 G Sedan

 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION >

JCMWM9741GB

Revision: 2011 November BCS-70 2011 G Sedan

 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION >

BCS

JCMWM9742GB

Revision: 2011 November BCS-71 2011 G Sedan

 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION >

JCMWM9743GB

Revision: 2011 November BCS-72 2011 G Sedan

 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION >

BCS

JCMWM9744GB

P
Fail-safe INFOID:0000000006211085

FAIL-SAFE CONTROL BY DTC

BCM performs fail-safe control when any DTC are detected.

Revision: 2011 November BCS-73 2011 G Sedan

 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION >

Display contents of CONSULT Fail-safe Cancellation

B2013: ID DISCORD BCM-S/L Inhibit engine cranking Erase DTC
B2014: CHAIN OF S/L-BCM Inhibit engine cranking Erase DTC
B2190: NATS ANTENNA AMP Inhibit engine cranking Erase DTC
B2191: DIFFERENCE OF KEY Inhibit engine cranking Erase DTC
B2192: ID DISCORD BCM-ECM Inhibit engine cranking Erase DTC
B2193: CHAIN OF BCM-ECM Inhibit engine cranking Erase DTC
B2195: ANTI-SCANNING Inhibit engine cranking Ignition switch ON → OFF
When normal vehicle speed signals are received from ABS actua-
B2557: VEHICLE SPEED Inhibit steering lock
tor and electric unit (control unit) for 500 ms
500 ms after the following CAN signal communication status be-
comes consistent
B2560: STARTER CONT RELAY Inhibit engine cranking
• Starter control relay signal
• Starter relay status signal
500 ms after the following signal reception status becomes consis-
tent
B2601: SHIFT POSITION Inhibit steering lock
• Selector lever P position switch signal
• P range signal (CAN)
5 seconds after the following BCM recognition conditions are ful-
filled
B2602: SHIFT POSITION Inhibit steering lock • Ignition switch is in the ON position
• Selector lever P position switch signal: Except P position (12 V)
• Vehicle speed: 4 km/h (2.5 MPH) or more
500 ms after the following BCM recognition conditions are fulfilled
• Ignition switch is in the ON position
B2603: SHIFT POSI STATUS Inhibit steering lock
• Selector lever P position switch signal: Except P position (12 V)
• Selector lever P/N position signal: Except P and N positions (0 V)
500 ms after any of the following BCM recognition conditions are
fulfilled
• Status 1
- Ignition switch is in the ON position
- Selector lever P/N position signal: P and N position (12 V)
B2604: PNP/CLUTCH SW Inhibit steering lock
- P range signal or N range signal (CAN): ON
• Status 2
- Ignition switch is in the ON position
- Selector lever P/N position signal: Except P and N positions (0 V)
- P range signal and N range signal (CAN): OFF
500 ms after any of the following BCM recognition conditions are
fulfilled
• Status 1
- Ignition switch is in the ON position
- Selector lever P/N position signal: Except P and N positions (0 V)
B2605: PNP/CLUTCH SW Inhibit steering lock
- Interlock/PNP switch signal (CAN): OFF
• Status 2
- Ignition switch is in the ON position
- Selector lever P/N position signal: P or N position (12 V)
- PNP switch signal (CAN): ON
500 ms after the following CAN signal communication status be-
comes consistent
B2606: S/L RELAY Inhibit engine cranking
• Steering lock relay signal (Request signal)
• Steering lock relay signal (Condition signal)
500 ms after the following CAN signal communication status has
becomes consistent
B2607: S/L RELAY Inhibit engine cranking
• Steering lock relay signal (Request signal)
• Steering lock relay signal (Condition signal)

Revision: 2011 November BCS-74 2011 G Sedan

 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION >
Display contents of CONSULT Fail-safe Cancellation
A
500 ms after the following signal communication status becomes
consistent
B2608: STARTER RELAY Inhibit engine cranking
• Starter motor relay control signal
• Starter relay status signal (CAN) B
When the following steering lock conditions agree
• Inhibit engine cranking • BCM steering lock control status
B2609: S/L STATUS
• Inhibit steering lock • Steering lock condition No. 1 signal status
• Steering lock condition No. 2 signal status
C
500 ms after the following conditions are fulfilled
• IGN relay (IPDM E/R) control signal: OFF (12 V)
B260A: IGNITION RELAY Inhibit engine cranking D
• Ignition ON signal (CAN to IPDM E/R): OFF (Request signal)
• Ignition ON signal (CAN from IPDM E/R): OFF (Condition signal)
Maintains the power supply When any of the following conditions are fulfilled
B260F: ENG STATE SIG LOST position attained at the time • Power position changes to ACC E
of DTC detection • Receives engine status signal (CAN)
When any of the following conditions are fulfilled
• Steering lock unit status signal (CAN) is received normally
B2612: S/L STATUS
• Inhibit engine cranking
• The BCM steering lock control status matches the steering lock
F
• Inhibit steering lock
status recognized by the steering lock unit status signal (CAN
from IPDM E/R)
1 second after the starter motor relay control inside BCM becomes G
B2617: BCM Inhibit engine cranking
normal
1 second after the ignition relay (IPDM E/R) control inside BCM be-
B2618: BCM Inhibit engine cranking
comes normal H
1 second after the steering lock unit power supply output control in-
B2619: BCM Inhibit engine cranking
side BCM becomes normal
B261E: VEHICLE TYPE Inhibit engine cranking BCM initialization I
When any of the following BCM recognition conditions are fulfilled
• Status 1
- Clutch switch signal (CAN from ECM): ON J
B26E8: CLUTCH SW Inhibit engine cranking - Clutch interlock switch signal: OFF (0 V)
• Status 2
- Clutch switch signal (CAN from ECM): OFF
- Clutch interlock switch signal: ON (Battery voltage) K
When BCM transmits the LOCK request signal to steering lock unit,
and receives LOCK response signal from steering lock unit, the fol-
• Inhibit engine cranking
B26E9: S/L STATUS lowing conditions are fulfilled L
• Inhibit steering lock
• Steering condition No. 1 signal: LOCK (0 V)
• Steering condition No. 2 signal: LOCK (12 V)

DTC Inspection Priority Chart INFOID:0000000006211086 BCS

If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.
N
Priority DTC
1 B2562: LOW VOLTAGE
O
• U1000: CAN COMM
2
• U1010: CONTROL UNIT(CAN)
• B2190: NATS ANTENNA AMP
• B2191: DIFFERENCE OF KEY
P
3 • B2192: ID DISCORD BCM-ECM
• B2193: CHAIN OF BCM-ECM
• B2195: ANTI-SCANNING

Revision: 2011 November BCS-75 2011 G Sedan

 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION >
Priority DTC
• B2013: ID DISCORD BCM-S/L
• B2014: CHAIN OF S/L-BCM
• B2553: IGNITION RELAY
• B2555: STOP LAMP
• B2556: PUSH-BTN IGN SW
• B2557: VEHICLE SPEED
• B2560: STARTER CONT RELAY
• B2601: SHIFT POSITION
• B2602: SHIFT POSITION
• B2603: SHIFT POSI STATUS
• B2604: PNP/CLUTCH SW
• B2605: PNP/CLUTCH SW
• B2606: S/L RELAY
• B2607: S/L RELAY
• B2608: STARTER RELAY
• B2609: S/L STATUS
• B260A: IGNITION RELAY
4 • B260B: STEERING LOCK UNIT
• B260C: STEERING LOCK UNIT
• B260D: STEERING LOCK UNIT
• B260F: ENG STATE SIG LOST
• B2612: S/L STATUS
• B2614: BCM
• B2615: BCM
• B2616: BCM
• B2617: BCM
• B2618: BCM
• B2619: BCM
• B261A: PUSH-BTN IGN SW
• B261E: VEHICLE TYPE
• B26E8: CLUTCH SW
• B26E9: S/L STATUS
• B26EA: KEY REGISTRATION
• C1729: VHCL SPEED SIG ERR
• U0415: VEHICLE SPEED
• C1704: LOW PRESSURE FL
• C1705: LOW PRESSURE FR
• C1706: LOW PRESSURE RR
• C1707: LOW PRESSURE RL
• C1708: [NO DATA] FL
• C1709: [NO DATA] FR
5 • C1710: [NO DATA] RR
• C1711: [NO DATA] RL
• C1716: [PRESSDATA ERR] FL
• C1717: [PRESSDATA ERR] FR
• C1718: [PRESSDATA ERR] RR
• C1719: [PRESSDATA ERR] RL
• C1734: CONTROL UNIT
• B2621: INSIDE ANTENNA
6 • B2622: INSIDE ANTENNA
• B2623: INSIDE ANTENNA

DTC Index INFOID:0000000006211087

NOTE:
The details of time display are as follows.
• CRNT: A malfunction is detected now.
• PAST: A malfunction was detected in the past.
IGN counter is displayed on Freeze Frame Data. For details of Freeze Frame Data, refer to BCS-15, "COM-
MON ITEM : CONSULT-III Function (BCM - COMMON ITEM)".

Revision: 2011 November BCS-76 2011 G Sedan

 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION >

Freeze Frame Data A

Tire pressure
•Vehicle Speed Intelligent Key Refer-
CONSULT display Fail-safe monitor warning
•Odo/Trip Meter warning lamp ON ence page
lamp ON
•Vehicle condition
B
No DTC is detected.
further testing — — — — —
may be required.
U1000: CAN COMM — — — — BCS-34 C
U1010: CONTROL UNIT(CAN) — — — — BCS-35
U0415: VEHICLE SPEED — — — — BCS-36
D
B2013: ID DISCORD BCM-S/L × × — — SEC-55
B2014: CHAIN OF S/L-BCM × × — — SEC-56
B2190: NATS ANTENNA AMP × — — — SEC-47 E
B2191: DIFFERENCE OF KEY × — — — SEC-50
B2192: ID DISCORD BCM-ECM × — — — SEC-51
F
B2193: CHAIN OF BCM-ECM × — — — SEC-53
B2195: ANTI-SCANNING × — — — SEC-54
B2553: IGNITION RELAY — × — — PCS-49 G
B2555: STOP LAMP — × — — SEC-59
B2556: PUSH-BTN IGN SW — × × — SEC-61
H
B2557: VEHICLE SPEED × × × — SEC-63
B2560: STARTER CONT RELAY × × × — SEC-64
B2562: LOW VOLTAGE — × — — BCS-37 I
B2601: SHIFT POSITION × × × — SEC-65
B2602: SHIFT POSITION × × × — SEC-68
B2603: SHIFT POSI STATUS × × × — SEC-70 J
B2604: PNP/CLUTCH SW × × × — SEC-73
B2605: PNP/CLUTCH SW × × × — SEC-75
K
B2606: S/L RELAY × × × — SEC-77
B2607: S/L RELAY × × × — SEC-78
B2608: STARTER RELAY × × × — SEC-80 L
B2609: S/L STATUS × × × — SEC-82
B260A: IGNITION RELAY × × × — PCS-51
BCS
B260B: STEERING LOCK UNIT — × × — SEC-86
B260C: STEERING LOCK UNIT — × × — SEC-87
B260D: STEERING LOCK UNIT — × × — SEC-88 N
B260F: ENG STATE SIG LOST × × × — SEC-89
B2612: S/L STATUS × × × — SEC-94
O
B2614: BCM — × × — PCS-53
B2615: BCM — × × — PCS-55
B2616: BCM — × × — PCS-57 P
B2617: BCM × × × — SEC-98
B2618: BCM × × × — PCS-59
B2619: BCM × × × — SEC-100
B261A: PUSH-BTN IGN SW — × × — PCS-60
× (Turn ON for 15
B261E: VEHICLE TYPE × × — SEC-101
seconds)

Revision: 2011 November BCS-77 2011 G Sedan

 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION >
Freeze Frame Data
Tire pressure
•Vehicle Speed Intelligent Key Refer-
CONSULT display Fail-safe monitor warning
•Odo/Trip Meter warning lamp ON ence page
lamp ON
•Vehicle condition
B2621: INSIDE ANTENNA — × — — DLK-59
B2622: INSIDE ANTENNA — × — — DLK-61
B2623: INSIDE ANTENNA — × — — DLK-63
B26E8: CLUTCH SW × × × — SEC-90
× (Turn ON for 15
B26E9: S/L STATUS × × — SEC-92
seconds)
× (Turn ON for 15
B26EA: KEY REGISTRATION — × — SEC-93
seconds)
C1704: LOW PRESSURE FL — — — ×
C1705: LOW PRESSURE FR — — — ×
WT-24
C1706: LOW PRESSURE RR — — — ×
C1707: LOW PRESSURE RL — — — ×
C1708: [NO DATA] FL — — — ×
C1709: [NO DATA] FR — — — ×
WT-26
C1710: [NO DATA] RR — — — ×
C1711: [NO DATA] RL — — — ×
C1716: [PRESSDATA ERR] FL — — — ×
C1717: [PRESSDATA ERR] FR — — — ×
WT-29
C1718: [PRESSDATA ERR] RR — — — ×
C1719: [PRESSDATA ERR] RL — — — ×
C1729: VHCL SPEED SIG ERR — — — × WT-30
C1734: CONTROL UNIT — — — × WT-31

Revision: 2011 November BCS-78 2011 G Sedan

 COMBINATION SWITCH SYSTEM SYMPTOMS
< SYMPTOM DIAGNOSIS >
SYMPTOM DIAGNOSIS A
COMBINATION SWITCH SYSTEM SYMPTOMS
Symptom Table INFOID:0000000006211088
B

1. Perform “Data Monitor” of CONSULT-III to check for any malfunctioning item.

2. Check the malfunction combinations. C
Malfunction item: ×
Data monitor item

HEAD LAMP SW 1

HEAD LAMP SW 2
D

AUTO LIGHT SW
FR WASHER SW

TURN SIGNAL R

TURN SIGNAL L
FR WIPER LOW

TAIL LAMP SW
FR WIPER INT

PASSING SW
FR WIPER HI

INT VOLUME

HI BEAM SW

FR FOG SW
Malfunction
combination
E

A × × × × F
B × × × ×
C × × ×
G
D × × ×
E × ×
F × × H
G × ×
H × × ×
I × × × × I
J × × × ×
K All Items J
L If only one item is detected or the item is not applicable to the combinations A to K

3. Identify the malfunctioning part from the agreed combination and repair or replace the part.
K
Malfunction
Malfunctioning part Repair or replace
combination
L
A Combination switch INPUT 1 circuit
B Combination switch INPUT 2 circuit
Inspect the combination switch input circuit applicable to the malfunctioning
C Combination switch INPUT 3 circuit BCS
part. Refer to BCS-39, "Diagnosis Procedure".
D Combination switch INPUT 4 circuit
E Combination switch INPUT 5 circuit
F Combination switch OUTPUT 1 circuit N
G Combination switch OUTPUT 2 circuit
Inspect the combination switch output circuit applicable to the malfunction-
H Combination switch OUTPUT 3 circuit
ing part. Refer to BCS-41, "Diagnosis Procedure". O
I Combination switch OUTPUT 4 circuit
J Combination switch OUTPUT 5 circuit
K BCM Replace BCM. Refer to BCS-82, "Exploded View" P
L Combination switch Replace the combination switch.

Revision: 2011 November BCS-79 2011 G Sedan

 NORMAL OPERATING CONDITION
< SYMPTOM DIAGNOSIS >
NORMAL OPERATING CONDITION
Description INFOID:0000000007868417

TRANSIT MODE
• Transit mode inhibits battery power consumption during transportation or storage of the vehicle.
• BCM is set to transit mode before delivery.
• In transit mode, remote keyless entry function, headlamp ON/OFF function, theft warning alarm function,
and other BCM control functions do not operate normally.
• Therefore, cancel operation must be performed so that the vehicle is used in normal status.
• For transit mode cancel operation, refer to BCS-4, "Description".
NOTE:
Do not cancel transit mode during storage of the vehicle. Always cancel transit mode before delivery of the
vehicle to customer.

Revision: 2011 November BCS-80 2011 G Sedan

 PRECAUTIONS
< PRECAUTION >
PRECAUTION A
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT B
PRE-TENSIONER" INFOID:0000000006211089

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along C
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted. D
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING: E
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
F
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”. G
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors. H
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation. I
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing J
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
K

BCS

Revision: 2011 November BCS-81 2011 G Sedan

 BCM (BODY CONTROL MODULE)
< REMOVAL AND INSTALLATION >
REMOVAL AND INSTALLATION
BCM (BODY CONTROL MODULE)
Exploded View INFOID:0000000006211090

JPMIA0063ZZ

1. BCM

Removal and Installation INFOID:0000000006211091

REMOVAL
1. Remove dash side finisher (passenger side). Refer to INT-15, "Exploded View".
2. Remove bolt and nut.
3. Remove BCM and disconnect the connector.
INSTALLATION
Install in the reverse order of removal.

Revision: 2011 November BCS-82 2011 G Sedan

 COMBINATION SWITCH
< REMOVAL AND INSTALLATION >
COMBINATION SWITCH
A
Exploded View INFOID:0000000006211092

JPLIA0050ZZ

1. Combination switch 2. Combination switch connector G

Removal and Installation INFOID:0000000006211093

H
REMOVAL
1. Remove steering column cover. Refer to IP-12, "A/T MODELS : Exploded View".
2. Remove screws. I
3. Disconnect the connector.
4. Pull up the combination switch to remove it.
J
INSTALLATION
Install in the reverse order of removal.
K

BCS

Revision: 2011 November BCS-83 2011 G Sedan