Scribd
Upload
25 views1 page

DS 2in - 150# BV - FB - FE - Chem-03

This data sheet provides specifications for FE ball valves, including sizes (10" and 2" NB), ANSI rating (150#), and design standards (API 6D). It details material specifications, construction design, testing requirements, and painting specifications, along with operational requirements like gear operator and actuator needs. The document is intended for the Replacement and Revamping of Pipeline Network at Oil Jetties Area, Kandla, under MECON's Technical Specification No. MEC/TS/05/21/002.

Uploaded by

Sachin Kumar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
25 views1 page

DS 2in - 150# BV - FB - FE - Chem-03

This data sheet provides specifications for FE ball valves, including sizes (10" and 2" NB), ANSI rating (150#), and design standards (API 6D). It details material specifications, construction design, testing requirements, and painting specifications, along with operational requirements like gear operator and actuator needs. The document is intended for the Replacement and Revamping of Pipeline Network at Oil Jetties Area, Kandla, under MECON's Technical Specification No. MEC/TS/05/21/002.

Uploaded by

Sachin Kumar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
You are on page 1/ 1

DATA SHEET FOR FE BALL VALVES

1.0 Valve Manufacturer :

2.0 Valve Size (NB), mm (inch) : 10" & 2" NB ANSI Rating : 150# Design Standard : API 6D

3.0 MECON's Technical Specification No. : MEC/TS/05/21/002, Rev-1, Ed-1

4.0 Connecting Pipeline Design Pressure, bar : 19 Design Temperature, °C : -29°C to + 65°C

5.0 Connecting Pipe Specification : N. A.


5.1 Material
5.2 Diameter (OD), mm (inch)
5.3 Thickness, mm

6.0 Valve Construction Design


6.1. Configuration : Reduced Bore Full Bore √
6.2. End Connections : Flanged as per ASME B16.5 √ Butt Welded as per ASME B16.25
6.3. Flanges (wherever applicable) : a) RF √ FF RT NA
b) Serrated Smooth (125 to 200 microinches AARH) √ NA
6.4 Ball Mounting : Trunion Mounted type for 10" Valves and Floating Ball type for 2" Valves
6.5 Valve body type : Fully Welded Two/Three Piece Bolted Either √

7.0 Valve Material Specification


Part Specified Material Material Offered (Equivalent or superior)
7.1 Body ASTM A 351 GR.CF8M / ASTM A 182 GR.F316
7.2 Ball SS304/ SS316
Body Seat Rings AISI 410
7.3 (No Casting)
7.4 Seat Seal RPTFE
7.5 Stem (No casting) AISI 410 / SS304/ SS316
7.6 Stem Seals GRAFOIL
7.7 Stud Bolts/ Nuts ASTM A 193 Gr. B7/ A194 Gr. 2H

8.0 Corrosion Allowance : 1.5 mm Service : Chemicals

9.0 Location : Above Ground √ Buried

10.0 Stem Extension Requirement : Yes No √ Length of Stem Extension, m : NA

11.0 Gear Operator Requirement : Yes √ (for 10") No √ (for 2")

12.0 Actuator Requirement : Yes No √

13.0 Fire Resistant Design Requirement : Type test as per API 6 FA/ API 607

14.0 Valve Testing Requirement

Test Pressure (min.), kg/cm2(g) Minimum Duration, minutes


For 10" For 2"
14.1 Hydrostatic Test Body 32 5 2
Seat 23 5 2
14.2 Air Test 5.6-7 2 2

15.0 Anti-Static Testing Requirement : As per Standard API 6D (Latest Ed.)

16.0 Valve Painting Specification


16.1 Surface preparation by Short Blasting as per grade SA 2 1/2, Swedish Standard SIS-055 909.
16.2 For above ground installation-Three coats of corrosion resistant paint shall be applied with minimum thickness of 300 micron
( Permissible thickness in each coat shall be within 80 to 120 micron). Colour of paint shade shall be RAL-7038, however any change in colour
shall be finalized during drawing approval stage.
17.0 Lock Open/ Lock Close/Normally Close Requirement : N. A.
Notes:
1. This Valve Data Sheet shall be read in conjunction with MECON's Technical Specification No. MEC/TS/05/21/002,Rev 1 ,Ed. 1
2. Inspection and Testing shall be as per attached QAP, this Data Sheet, MECON's T.S., API 6D and other relevant standards.
3. Stops shall be provided for positive alignment of ball with ports and ensure proper installation of handle.
4. Short pattern valves (as per API 6D or otherwise) are not permitted. Only long pattern valves are to be supplied.
5. Charpy V-notch & Hardness test for body, body adaptor, end flanges, ball, body seat rings, stem & studs / nuts shall be conducted
as per Cl. 3.4 & 3.6 of TS respectively or as per relevant material code.
6. Compressed asbestos fibre (CAF) shall not be used for body sealing / gasket materials.
7. Material for body shall have a guaranteed minimum yield strength of 35000 psi. In case the same cannot be guaranteed, valves shall
be provided with a 500 mm pup piece (integrally welded to the valve on each side) with strength equivalent to that of the connecting pipe. - N.A.
8. For welding end, the out of roundness (i. e. difference between maximum and minimum ID at pipe end) shall not be more than 0.5% of pipe OD - N.A.
9. Valves shall be inspected and approved by Purchaser before despatch.
10 Support foot & lifting lugs shall be provided as per Cl. 4.16 of the TS for Ball Valves
REV. NO. DATE ZONE DESCRIPTIONS BY APPRD
REVISIONS REFERENCES DRG. NO.
SECTION PROCESS & PIPING CLIENT : DEENDAYAL PORT TRUST
NAME DATE CHKD DATE SUPPLIER :
DSGN Sachin 22.11.217 Harsh 22.11.2017 SUB SUPPLIER : MECON LIMITED
PROJECT : Replacement and Revamping of Pipeline
DRWN Network at Oil Jetties Area, Kandla
SCALE : REV
APPROVED Anil Kumar,DGM DATA SHEET FOR BALL VALVES DATA SHEET NO.: MEC/Q7F2/05/28/M/001/DS/BV/03 0
(NB ≥ 2")

You might also like