Scribd
Upload
12 views

Surface Texture 2

The Taylor–Hobson Talysurf is an electronic instrument used for measuring surface roughness, capable of operating in various environments. It utilizes a stylus and an armature system to detect surface irregularities, with outputs recorded and analyzed for roughness values. Alternative methods for measuring surface roughness include pneumatic methods, light interference microscopes, and the Mecrin instrument, each with unique principles and applications.

Uploaded by

nabasurjya14
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
12 views

Surface Texture 2

The Taylor–Hobson Talysurf is an electronic instrument used for measuring surface roughness, capable of operating in various environments. It utilizes a stylus and an armature system to detect surface irregularities, with outputs recorded and analyzed for roughness values. Alternative methods for measuring surface roughness include pneumatic methods, light interference microscopes, and the Mecrin instrument, each with unique principles and applications.

Uploaded by

nabasurjya14
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Taylor–Hobson Talysurf

The Taylor–Hobson talysurf works on the


same principle as that of the Tomlinson
surface meter. However, unlike the surface
meter, which is purely a mechanical
instrument, the talysurf is an electronic
instrument. This factor makes the talysurf a
more versatile instrument and can be used in
any condition, be it a metrology laboratory or
the factory shop floor. Fig. 10 Taylor–Hobson talysurf

.
Figure 10 illustrates the cross section of the measuring head. The stylus is attached to an
armature, which pivots about the centre of piece of an E-shaped stamping

The outer legs of the E-shaped stamping are wound with electrical coils. A predetermined value
of alternating current (excitation current) is supplied to the coils. The coils form part of a bridge
circuit. A skid or shoe provides the datum to plot surface roughness. The measuring head can
be traversed in a linear path by an electric motor. The motor, which may be of a variable speed
type or provided with a gear box, provides the required speed for the movement of the
measuring head.

As the stylus moves up and down due to


surface irregularities, the armature is also
displaced. This causes variation in the air
gap, leading to an imbalance in the bridge
circuit. The resulting bridge circuit output
consists of only modulation.

This is fed to an amplifier and a pen recorder


is used to make a permanent record (Fig. 11).
The instrument has the capability to calculate
and display the roughness value according to
a standard formula.
Profilometer

A profilometer is a compact device that can be used for the direct measurement of surface
texture. A finely pointed stylus will be in contact with the workpiece surface. An electrical
pickup attached to the stylus amplifies the signal and feeds it to either an indicating unit or a
recording unit. The stylus may be moved either by hand or by a motorized mechanism. The
profilometer is capable of measuring roughness together with waviness and any other surface
flaws. It provides a quick-fix means of conducting an initial investigation before attempting a
major investigation of surface quality.

WAVELENGTH, FREQUENCY, AND CUT-OFF

The complete traverse length of the stylus instrument


is called the measuring traverse length. It is divided
into several sampling lengths. The sampling length is
chosen based on the surface under test. Generally,
results of all the samples in the measuring traverse
length are averaged out by the instrument to give the
final result.

Skids simplify surface assessment while using stylus


instruments. However, there is a distortion because of
phase relationship between the stylus and the skid. Fig. 12 Phase relationship between the skid and
stylus
This aspect is illustrated in Fig.12. In case A, the stylus and the skid are in phase. Therefore,
roughness (the primary texture) will be relatively undistorted. In case B, the two are out of
phase. In this situation, waviness superimposes on the roughness reading and is misleading. In
case C also, the stylus and skid are out of phase, resulting in an unrealistic interpretation of
roughness value.

Thus, since the skid, like the stylus, is also rising and falling according to the surface asperities,
stylus height measurement may be distorted. Therefore, care must be exercised for the selection
of sampling length.
Cut-off Wavelength

The frequency of the stylus movement as it rises up and down the workpiece surface is
determined by the traversing speed. Assuming that f is the frequency of the stylus movement,
λ is the surface wavelength, and v is the traverse speed, one gets the following equation:

f = v/λ

Therefore, f ∝ 1/λ, if v remains constant.

For surfaces produced by single-point cutting tools, a simple guideline for selecting cut-off

wavelength is that it should not exceed one feed spacing. However, for many fine irregular

surfaces, a cut-off length of 0.8mm is recommended. Table 1 illustrates the recommended

cut-off wavelengths for machining processes.

Table 1 Recommended wavelengths for machining processes

Finishing processes Superfinishing, lapping, Cut-off length (mm)


honing, diamond boring, polishing, and buffing 0.25–0.8
Grinding 0.25–0.8
Turning, reaming, and broaching 0.8–2.5
Boring, milling, and shaping 0.8–8.0
Planning 2.5–25

OTHER METHODS FOR MEASURING SURFACE ROUGHNESS

In addition to the stylus-based methods of surface roughness measurement explained above


this section presents in brief some of the alternative methods used in the industry.
Pneumatic Method

The air leakage method is often used for assessing surface texture. A pneumatic comparator is
used for conducting mass inspection of parts. Compressed air is discharged from a self-aligning
nozzle held close to the surface being inspected. Depending on height variations in the surface
irregularities, the gap between the nozzle tip and the workpiece surface varies. This results in

the variation of flow rate of air, which in turn varies the rotation speed of a rotameter. Rotation
of the rotameter is an indication of surface irregularities. Alternatively, a float can also be used
to measure surface deviations. The comparator is initially set using reference gauges.
Light Interference Microscopes

The light interference technique offers a non-contact method of assessing surface texture.
Advantages of this method are that it allows an area of the workpiece surface to be examined,
a wide range of magnifications to be used, and the opportunity for making a permanent record
of the fringe pattern using a camera. Good magnification capability allows good resolution up
to a scratch spacing of 0.5µm.

A monochromatic light passing through an optical flat and falling on the workpiece surface
generates the fringe pattern. However, assessment of surface irregularities cannot be directly
related to the Ra value. Master specimens are used to generate a reference fringe pattern, which
is compared with the fringe pattern of the workpiece in order to arrive at a conclusion regarding
surface quality. This method provides a viable alternative for inspecting soft or thin surfaces,
which normally cannot be examined using stylus instruments.

Mecrin Instrument

The Mecrin instrument assesses surface irregularities through frictional properties and the
average slope of the irregularities. This gauge is suited for surfaces manufactured by processes
such as grinding, honing, and lapping, which have low Ra values in the range 3–5 µm. Figure
13 illustrates the working principle of this instrument.

A thin metallic blade is pushed


against the workpiece surface at a
certain angle. The blade may slide
or buckle, depending on the surface
roughness and the angle of attack.
At lower angles of attack, the blade
tip will slide over the surface of the
workpiece. As the angle of attack is Fig.13 Principle of the Mecrin instrument

increased, a critical value is reached at which the blade starts to buckle. This critical angle is a
measure of the degree of roughness of the surface. The instrument is provided with additional
features for easier handling. A graduated dial will directly give the reading of roughness value.

You might also like